Merge tag 'armsoc-fixes-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC fixes from Arnd Bergmann:
 "This is a bit larger than normal, as we had not managed to send out a
  pull request before traveling for a week without my signing key.

  There are multiple code fixes for older bugs, all of which should get
  backported into stable kernels:

   - tango: one fix for multiplatform configurations broken on other
     platforms when tango is enabled

   - arm_scmi: device unregistration fix

   - iop32x: fix kernel oops from extraneous __init annotation

   - pxa: remove a double kfree

   - fsl qbman: close an interrupt clearing race

  The rest is the usual collection of smaller fixes for device tree
  files, on the renesas, allwinner, meson, omap, davinci, qualcomm and
  imx platforms.

  Some of these are for compile-time warnings, most are for board
  specific functionality that fails to work because of incorrect
  settings"

* tag 'armsoc-fixes-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (30 commits)
  ARM: tango: Improve ARCH_MULTIPLATFORM compatibility
  firmware: arm_scmi: provide the mandatory device release callback
  ARM: iop32x/n2100: fix PCI IRQ mapping
  arm64: dts: add msm8996 compatible to gicv3
  ARM: dts: am335x-shc.dts: fix wrong cd pin level
  ARM: dts: n900: fix mmc1 card detect gpio polarity
  ARM: dts: omap3-gta04: Fix graph_port warning
  ARM: pxa: ssp: unneeded to free devm_ allocated data
  ARM: dts: r8a7743: Convert to new LVDS DT bindings
  soc: fsl: qbman: avoid race in clearing QMan interrupt
  arm64: dts: renesas: r8a77965: Enable DMA for SCIF2
  arm64: dts: renesas: r8a7796: Enable DMA for SCIF2
  arm64: dts: renesas: r8a774a1: Enable DMA for SCIF2
  ARM: dts: da850: fix interrupt numbers for clocksource
  dt-bindings: imx8mq: Number clocks consecutively
  arm64: dts: meson: Fix mmc cd-gpios polarity
  ARM: dts: imx6sx: correct backward compatible of gpt
  ARM: dts: imx: replace gpio-key,wakeup with wakeup-source property
  ARM: dts: vf610-bk4: fix incorrect #address-cells for dspi3
  ARM: dts: meson8m2: mxiii-plus: mark the SD card detection GPIO active-low
  ...

arch/arm/boot/dts/am335x-shc.dts

@@ -215,7 +215,7 @@ &mmc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins>;
 	bus-width = <0x4>;
-	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
 	cd-inverted;
 	max-frequency = <26000000>;
 	vmmc-supply = <&vmmcsd_fixed>;

arch/arm/boot/dts/da850.dtsi

@@ -476,7 +476,7 @@ i2c1: i2c@228000 {
 		clocksource: timer@20000 {
 			compatible = "ti,da830-timer";
 			reg = <0x20000 0x1000>;
-			interrupts = <12>, <13>;
+			interrupts = <21>, <22>;
 			interrupt-names = "tint12", "tint34";
 			clocks = <&pll0_auxclk>;
 		};

arch/arm/boot/dts/imx6q-pistachio.dts

@@ -103,7 +103,7 @@ gpio-keys {
 		power {
 			label = "Power Button";
 			gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
-			gpio-key,wakeup;
+			wakeup-source;
 			linux,code = <KEY_POWER>;
 		};
 	};

arch/arm/boot/dts/imx6sll-evk.dts

@@ -309,7 +309,7 @@ &usdhc3 {
 	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
 	cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
 	keep-power-in-suspend;
-	enable-sdio-wakeup;
+	wakeup-source;
 	vmmc-supply = <&reg_sd3_vmmc>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6sx.dtsi

@@ -467,7 +467,7 @@ flexcan2: can@2094000 {
 			};
 
 			gpt: gpt@2098000 {
-				compatible = "fsl,imx6sx-gpt", "fsl,imx31-gpt";
+				compatible = "fsl,imx6sx-gpt", "fsl,imx6dl-gpt";
 				reg = <0x02098000 0x4000>;
 				interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SX_CLK_GPT_BUS>,

arch/arm/boot/dts/meson.dtsi

@@ -274,7 +274,7 @@ ethmac: ethernet@c9410000 {
 			compatible = "amlogic,meson6-dwmac", "snps,dwmac";
 			reg = <0xc9410000 0x10000
 			       0xc1108108 0x4>;
-			interrupts = <GIC_SPI 8 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
 			status = "disabled";
 		};

arch/arm/boot/dts/meson8b-ec100.dts

@@ -205,8 +205,7 @@ sd_card_slot: slot@1 {
 		cap-sd-highspeed;
 		disable-wp;
 
-		cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-		cd-inverted;
+		cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 		vmmc-supply = <&vcc_3v3>;
 	};

arch/arm/boot/dts/meson8b-odroidc1.dts

@@ -221,7 +221,6 @@ mdio {
 		/* Realtek RTL8211F (0x001cc916) */
 		eth_phy: ethernet-phy@0 {
 			reg = <0>;
-			eee-broken-1000t;
 			interrupt-parent = <&gpio_intc>;
 			/* GPIOH_3 */
 			interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
@@ -273,8 +272,7 @@ sd_card_slot: slot@1 {
 		cap-sd-highspeed;
 		disable-wp;
 
-		cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-		cd-inverted;
+		cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 		vmmc-supply = <&tflash_vdd>;
 		vqmmc-supply = <&tf_io>;

arch/arm/boot/dts/meson8m2-mxiii-plus.dts

@@ -206,8 +206,7 @@ sd_card_slot: slot@1 {
 		cap-sd-highspeed;
 		disable-wp;
 
-		cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-		cd-inverted;
+		cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 		vmmc-supply = <&vcc_3v3>;
 	};

arch/arm/boot/dts/motorola-cpcap-mapphone.dtsi

@@ -105,7 +105,7 @@ cpcap_usb2_phy: phy {
 			interrupts-extended = <
 				&cpcap 15 0 &cpcap 14 0 &cpcap 28 0 &cpcap 19 0
 				&cpcap 18 0 &cpcap 17 0 &cpcap 16 0 &cpcap 49 0
-				&cpcap 48 1
+				&cpcap 48 0
 			>;
 			interrupt-names =
 				"id_ground", "id_float", "se0conn", "vbusvld",

arch/arm/boot/dts/omap3-gta04.dtsi

@@ -714,11 +714,7 @@ &venc {
 
 	vdda-supply = <&vdac>;
 
-	#address-cells = <1>;
-	#size-cells = <0>;
-
 	port {
-		reg = <0>;
 		venc_out: endpoint {
 			remote-endpoint = <&opa_in>;
 			ti,channels = <1>;

arch/arm/boot/dts/omap3-n900.dts

@@ -814,7 +814,7 @@ &mmc1 {
 	/* For debugging, it is often good idea to remove this GPIO.
 	   It means you can remove back cover (to reboot by removing
 	   battery) and still use the MMC card. */
-	cd-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>; /* 160 */
+	cd-gpios = <&gpio6 0 GPIO_ACTIVE_LOW>; /* 160 */
 };
 
 /* most boards use vaux3, only some old versions use vmmc2 instead */

arch/arm/boot/dts/omap3-n950-n9.dtsi

@@ -370,6 +370,19 @@ onenand@0,0 {
 		compatible = "ti,omap2-onenand";
 		reg = <0 0 0x20000>;	/* CS0, offset 0, IO size 128K */
 
+		/*
+		 * These timings are based on CONFIG_OMAP_GPMC_DEBUG=y reported
+		 * bootloader set values when booted with v4.19 using both N950
+		 * and N9 devices (OneNAND Manufacturer: Samsung):
+		 *
+		 *   gpmc cs0 before gpmc_cs_program_settings:
+		 *   cs0 GPMC_CS_CONFIG1: 0xfd001202
+		 *   cs0 GPMC_CS_CONFIG2: 0x00181800
+		 *   cs0 GPMC_CS_CONFIG3: 0x00030300
+		 *   cs0 GPMC_CS_CONFIG4: 0x18001804
+		 *   cs0 GPMC_CS_CONFIG5: 0x03171d1d
+		 *   cs0 GPMC_CS_CONFIG6: 0x97080000
+		 */
 		gpmc,sync-read;
 		gpmc,sync-write;
 		gpmc,burst-length = <16>;
@@ -379,26 +392,27 @@ onenand@0,0 {
 		gpmc,device-width = <2>;
 		gpmc,mux-add-data = <2>;
 		gpmc,cs-on-ns = <0>;
-		gpmc,cs-rd-off-ns = <87>;
-		gpmc,cs-wr-off-ns = <87>;
+		gpmc,cs-rd-off-ns = <122>;
+		gpmc,cs-wr-off-ns = <122>;
 		gpmc,adv-on-ns = <0>;
-		gpmc,adv-rd-off-ns = <10>;
-		gpmc,adv-wr-off-ns = <10>;
-		gpmc,oe-on-ns = <15>;
-		gpmc,oe-off-ns = <87>;
+		gpmc,adv-rd-off-ns = <15>;
+		gpmc,adv-wr-off-ns = <15>;
+		gpmc,oe-on-ns = <20>;
+		gpmc,oe-off-ns = <122>;
 		gpmc,we-on-ns = <0>;
-		gpmc,we-off-ns = <87>;
-		gpmc,rd-cycle-ns = <112>;
-		gpmc,wr-cycle-ns = <112>;
-		gpmc,access-ns = <81>;
+		gpmc,we-off-ns = <122>;
+		gpmc,rd-cycle-ns = <148>;
+		gpmc,wr-cycle-ns = <148>;
+		gpmc,access-ns = <117>;
 		gpmc,page-burst-access-ns = <15>;
 		gpmc,bus-turnaround-ns = <0>;
 		gpmc,cycle2cycle-delay-ns = <0>;
 		gpmc,wait-monitoring-ns = <0>;
-		gpmc,clk-activation-ns = <5>;
-		gpmc,wr-data-mux-bus-ns = <30>;
-		gpmc,wr-access-ns = <81>;
-		gpmc,sync-clk-ps = <15000>;
+		gpmc,clk-activation-ns = <10>;
+		gpmc,wr-data-mux-bus-ns = <40>;
+		gpmc,wr-access-ns = <117>;
+
+		gpmc,sync-clk-ps = <15000>; /* TBC; Where this value came? */
 
 		/*
 		 * MTD partition table corresponding to Nokia's MeeGo 1.2

arch/arm/boot/dts/omap5-l4.dtsi

@@ -1046,8 +1046,6 @@ SYSC_OMAP2_SOFTRESET |
 					<SYSC_IDLE_SMART>,
 					<SYSC_IDLE_SMART_WKUP>;
 			ti,syss-mask = <1>;
-			ti,no-reset-on-init;
-			ti,no-idle-on-init;
 			/* Domains (V, P, C): core, core_pwrdm, l4per_clkdm */
 			clocks = <&l4per_clkctrl OMAP5_UART3_CLKCTRL 0>;
 			clock-names = "fck";

arch/arm/boot/dts/r8a7743.dtsi

@@ -1681,15 +1681,12 @@ vsp@fe938000 {
 
 		du: display@feb00000 {
 			compatible = "renesas,du-r8a7743";
-			reg = <0 0xfeb00000 0 0x40000>,
-			      <0 0xfeb90000 0 0x1c>;
-			reg-names = "du", "lvds.0";
+			reg = <0 0xfeb00000 0 0x40000>;
 			interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 724>,
-				 <&cpg CPG_MOD 723>,
-				 <&cpg CPG_MOD 726>;
-			clock-names = "du.0", "du.1", "lvds.0";
+				 <&cpg CPG_MOD 723>;
+			clock-names = "du.0", "du.1";
 			status = "disabled";
 
 			ports {
@@ -1704,6 +1701,33 @@ du_out_rgb: endpoint {
 				port@1 {
 					reg = <1>;
 					du_out_lvds0: endpoint {
+						remote-endpoint = <&lvds0_in>;
+					};
+				};
+			};
+		};
+
+		lvds0: lvds@feb90000 {
+			compatible = "renesas,r8a7743-lvds";
+			reg = <0 0xfeb90000 0 0x1c>;
+			clocks = <&cpg CPG_MOD 726>;
+			power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
+			resets = <&cpg 726>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					lvds0_in: endpoint {
+						remote-endpoint = <&du_out_lvds0>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					lvds0_out: endpoint {
 					};
 				};
 			};

arch/arm/boot/dts/sun6i-a31.dtsi

@@ -216,6 +216,7 @@ osc24M: clk-24M {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <24000000>;
+			clock-output-names = "osc24M";
 		};
 
 		osc32k: clk-32k {

arch/arm/boot/dts/sun8i-h3-beelink-x2.dts

@@ -53,7 +53,7 @@ / {
 
 	aliases {
 		serial0 = &uart0;
-		/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+		ethernet0 = &emac;
 		ethernet1 = &sdiowifi;
 	};
 

arch/arm/boot/dts/vf610-bk4.dts

@@ -110,11 +110,11 @@ &dspi3 {
 	bus-num = <3>;
 	status = "okay";
 	spi-slave;
+	#address-cells = <0>;
 
-	slave@0 {
+	slave {
 		compatible = "lwn,bk4";
 		spi-max-frequency = <30000000>;
-		reg = <0>;
 	};
 };
 

arch/arm/mach-iop32x/n2100.c

@@ -75,8 +75,7 @@ void __init n2100_map_io(void)
 /*
  * N2100 PCI.
  */
-static int __init
-n2100_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+static int n2100_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
 {
 	int irq;
 

arch/arm/mach-tango/pm.c

@@ -3,6 +3,7 @@
 #include <linux/suspend.h>
 #include <asm/suspend.h>
 #include "smc.h"
+#include "pm.h"
 
 static int tango_pm_powerdown(unsigned long arg)
 {
@@ -24,10 +25,7 @@ static const struct platform_suspend_ops tango_pm_ops = {
 	.valid = suspend_valid_only_mem,
 };
 
-static int __init tango_pm_init(void)
+void __init tango_pm_init(void)
 {
 	suspend_set_ops(&tango_pm_ops);
-	return 0;
 }
-
-late_initcall(tango_pm_init);

arch/arm/mach-tango/pm.h

+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifdef CONFIG_SUSPEND
+void __init tango_pm_init(void);
+#else
+#define tango_pm_init NULL
+#endif

arch/arm/mach-tango/setup.c

@@ -2,6 +2,7 @@
 #include <asm/mach/arch.h>
 #include <asm/hardware/cache-l2x0.h>
 #include "smc.h"
+#include "pm.h"
 
 static void tango_l2c_write(unsigned long val, unsigned int reg)
 {
@@ -15,4 +16,5 @@ DT_MACHINE_START(TANGO_DT, "Sigma Tango DT")
 	.dt_compat	= tango_dt_compat,
 	.l2c_aux_mask	= ~0,
 	.l2c_write_sec	= tango_l2c_write,
+	.init_late	= tango_pm_init,
 MACHINE_END

arch/arm/plat-pxa/ssp.c

@@ -190,8 +190,6 @@ static int pxa_ssp_remove(struct platform_device *pdev)
 	if (ssp == NULL)
 		return -ENODEV;
 
-	iounmap(ssp->mmio_base);
-
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	release_mem_region(res->start, resource_size(res));
 
@@ -201,7 +199,6 @@ static int pxa_ssp_remove(struct platform_device *pdev)
 	list_del(&ssp->node);
 	mutex_unlock(&ssp_lock);
 
-	kfree(ssp);
 	return 0;
 }
 

arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts

@@ -188,6 +188,7 @@ axp803: pmic@3a3 {
 		reg = <0x3a3>;
 		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */
 	};
 };
 

arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi

@@ -390,7 +390,7 @@ tcon1_out_hdmi: endpoint@1 {
 		};
 
 		video-codec@1c0e000 {
-			compatible = "allwinner,sun50i-h5-video-engine";
+			compatible = "allwinner,sun50i-a64-video-engine";
 			reg = <0x01c0e000 0x1000>;
 			clocks = <&ccu CLK_BUS_VE>, <&ccu CLK_VE>,
 				 <&ccu CLK_DRAM_VE>;

arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi

@@ -187,8 +187,7 @@ &sd_emmc_b {
 	max-frequency = <100000000>;
 	disable-wp;
 
-	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 	vmmc-supply = <&vddao_3v3>;
 	vqmmc-supply = <&vddio_boot>;

arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts

@@ -305,8 +305,7 @@ &sd_emmc_b {
 	max-frequency = <200000000>;
 	disable-wp;
 
-	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 	vmmc-supply = <&vddio_ao3v3>;
 	vqmmc-supply = <&vddio_tf>;

arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts

@@ -238,8 +238,7 @@ &sd_emmc_b {
 	max-frequency = <100000000>;
 	disable-wp;
 
-	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 	vmmc-supply = <&vddao_3v3>;
 	vqmmc-supply = <&vddio_card>;

arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts

@@ -258,8 +258,7 @@ &sd_emmc_b {
 	max-frequency = <100000000>;
 	disable-wp;
 
-	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 	vmmc-supply = <&tflash_vdd>;
 	vqmmc-supply = <&tf_io>;

arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi

@@ -196,8 +196,7 @@ &sd_emmc_b {
 	max-frequency = <100000000>;
 	disable-wp;
 
-	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 	vmmc-supply = <&vddao_3v3>;
 	vqmmc-supply = <&vddio_card>;

arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi

@@ -154,8 +154,7 @@ &sd_emmc_b {
 	max-frequency = <100000000>;
 	disable-wp;
 
-	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 	vmmc-supply = <&vcc_3v3>;
 };

arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi

@@ -211,8 +211,7 @@ &sd_emmc_b {
 	max-frequency = <100000000>;
 	disable-wp;
 
-	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 	vmmc-supply = <&vddao_3v3>;
 	vqmmc-supply = <&vcc_3v3>;

arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts

@@ -131,8 +131,7 @@ &sd_emmc_b {
 	max-frequency = <100000000>;
 	disable-wp;
 
-	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 	vmmc-supply = <&vddao_3v3>;
 	vqmmc-supply = <&vddio_card>;

arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts

@@ -238,8 +238,7 @@ &sd_emmc_b {
 	max-frequency = <100000000>;
 	disable-wp;
 
-	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 	vmmc-supply = <&vcc_3v3>;
 	vqmmc-supply = <&vcc_card>;

arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts

@@ -183,8 +183,7 @@ &sd_emmc_b {
 	max-frequency = <100000000>;
 	disable-wp;
 
-	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 	vmmc-supply = <&vddao_3v3>;
 	vqmmc-supply = <&vddio_card>;

arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi

@@ -137,8 +137,7 @@ &sd_emmc_b {
 	max-frequency = <100000000>;
 	disable-wp;
 
-	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 	vmmc-supply = <&vddao_3v3>;
 	vqmmc-supply = <&vddio_boot>;

arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts

@@ -356,8 +356,7 @@ &sd_emmc_b {
 	max-frequency = <100000000>;
 	disable-wp;
 
-	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 	vmmc-supply = <&vddao_3v3>;
 	vqmmc-supply = <&vddio_boot>;

arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts

@@ -147,8 +147,7 @@ &sd_emmc_b {
 	max-frequency = <100000000>;
 	disable-wp;
 
-	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 	vmmc-supply = <&vddao_3v3>;
 	vqmmc-supply = <&vddio_boot>;

arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts

@@ -170,8 +170,7 @@ &sd_emmc_b {
 	max-frequency = <100000000>;
 	disable-wp;
 
-	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 	vmmc-supply = <&vddao_3v3>;
 	vqmmc-supply = <&vddio_boot>;

arch/arm64/boot/dts/qcom/msm8996.dtsi

@@ -404,7 +404,7 @@ tcsr: syscon@7a0000 {
 		};
 
 		intc: interrupt-controller@9bc0000 {
-			compatible = "arm,gic-v3";
+			compatible = "qcom,msm8996-gic-v3", "arm,gic-v3";
 			#interrupt-cells = <3>;
 			interrupt-controller;
 			#redistributor-regions = <1>;

arch/arm64/boot/dts/renesas/r8a774a1.dtsi

@@ -1011,6 +1011,9 @@ scif2: serial@e6e88000 {
 				 <&cpg CPG_CORE R8A774A1_CLK_S3D1>,
 				 <&scif_clk>;
 			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x13>, <&dmac1 0x12>,
+			       <&dmac2 0x13>, <&dmac2 0x12>;
+			dma-names = "tx", "rx", "tx", "rx";
 			power-domains = <&sysc R8A774A1_PD_ALWAYS_ON>;
 			resets = <&cpg 310>;
 			status = "disabled";

arch/arm64/boot/dts/renesas/r8a7796.dtsi

@@ -1262,6 +1262,9 @@ scif2: serial@e6e88000 {
 				 <&cpg CPG_CORE R8A7796_CLK_S3D1>,
 				 <&scif_clk>;
 			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x13>, <&dmac1 0x12>,
+			       <&dmac2 0x13>, <&dmac2 0x12>;
+			dma-names = "tx", "rx", "tx", "rx";
 			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
 			resets = <&cpg 310>;
 			status = "disabled";

arch/arm64/boot/dts/renesas/r8a77965.dtsi

@@ -1068,6 +1068,9 @@ scif2: serial@e6e88000 {
 				 <&cpg CPG_CORE R8A77965_CLK_S3D1>,
 				 <&scif_clk>;
 			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x13>, <&dmac1 0x12>,
+			       <&dmac2 0x13>, <&dmac2 0x12>;
+			dma-names = "tx", "rx", "tx", "rx";
 			power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
 			resets = <&cpg 310>;
 			status = "disabled";

drivers/firmware/arm_scmi/bus.c

@@ -119,6 +119,11 @@ void scmi_driver_unregister(struct scmi_driver *driver)
 }
 EXPORT_SYMBOL_GPL(scmi_driver_unregister);
 
+static void scmi_device_release(struct device *dev)
+{
+	kfree(to_scmi_dev(dev));
+}
+
 struct scmi_device *
 scmi_device_create(struct device_node *np, struct device *parent, int protocol)
 {
@@ -138,6 +143,7 @@ scmi_device_create(struct device_node *np, struct device *parent, int protocol)
 	scmi_dev->dev.parent = parent;
 	scmi_dev->dev.of_node = np;
 	scmi_dev->dev.bus = &scmi_bus_type;
+	scmi_dev->dev.release = scmi_device_release;
 	dev_set_name(&scmi_dev->dev, "scmi_dev.%d", id);
 
 	retval = device_register(&scmi_dev->dev);
@@ -156,9 +162,8 @@ scmi_device_create(struct device_node *np, struct device *parent, int protocol)
 void scmi_device_destroy(struct scmi_device *scmi_dev)
 {
 	scmi_handle_put(scmi_dev->handle);
-	device_unregister(&scmi_dev->dev);
 	ida_simple_remove(&scmi_bus_id, scmi_dev->id);
-	kfree(scmi_dev);
+	device_unregister(&scmi_dev->dev);
 }
 
 void scmi_set_handle(struct scmi_device *scmi_dev)

drivers/soc/fsl/qbman/qman.c

@@ -1143,18 +1143,19 @@ static void qm_mr_process_task(struct work_struct *work);
 static irqreturn_t portal_isr(int irq, void *ptr)
 {
 	struct qman_portal *p = ptr;
-
-	u32 clear = QM_DQAVAIL_MASK | p->irq_sources;
 	u32 is = qm_in(&p->p, QM_REG_ISR) & p->irq_sources;
+	u32 clear = 0;
 
 	if (unlikely(!is))
 		return IRQ_NONE;
 
 	/* DQRR-handling if it's interrupt-driven */
-	if (is & QM_PIRQ_DQRI)
+	if (is & QM_PIRQ_DQRI) {
 		__poll_portal_fast(p, QMAN_POLL_LIMIT);
+		clear = QM_DQAVAIL_MASK | QM_PIRQ_DQRI;
+	}
 	/* Handling of anything else that's interrupt-driven */
-	clear |= __poll_portal_slow(p, is);
+	clear |= __poll_portal_slow(p, is) & QM_PIRQ_SLOW;
 	qm_out(&p->p, QM_REG_ISR, clear);
 	return IRQ_HANDLED;
 }

include/dt-bindings/clock/imx8mq-clock.h

@@ -350,7 +350,7 @@
 #define IMX8MQ_CLK_VPU_G2_ROOT			241
 
 /* SCCG PLL GATE */
-#define IMX8MQ_SYS1_PLL_OUT			232
+#define IMX8MQ_SYS1_PLL_OUT			242
 #define IMX8MQ_SYS2_PLL_OUT			243
 #define IMX8MQ_SYS3_PLL_OUT			244
 #define IMX8MQ_DRAM_PLL_OUT			245
@@ -372,24 +372,24 @@
 /* txesc clock */
 #define IMX8MQ_CLK_DSI_IPG_DIV                  256
 
-#define IMX8MQ_CLK_TMU_ROOT			265
+#define IMX8MQ_CLK_TMU_ROOT			257
 
 /* Display root clocks */
-#define IMX8MQ_CLK_DISP_AXI_ROOT		266
-#define IMX8MQ_CLK_DISP_APB_ROOT		267
-#define IMX8MQ_CLK_DISP_RTRM_ROOT		268
+#define IMX8MQ_CLK_DISP_AXI_ROOT		258
+#define IMX8MQ_CLK_DISP_APB_ROOT		259
+#define IMX8MQ_CLK_DISP_RTRM_ROOT		260
 
-#define IMX8MQ_CLK_OCOTP_ROOT			269
+#define IMX8MQ_CLK_OCOTP_ROOT			261
 
-#define IMX8MQ_CLK_DRAM_ALT_ROOT		270
-#define IMX8MQ_CLK_DRAM_CORE			271
+#define IMX8MQ_CLK_DRAM_ALT_ROOT		262
+#define IMX8MQ_CLK_DRAM_CORE			263
 
-#define IMX8MQ_CLK_MU_ROOT			272
-#define IMX8MQ_VIDEO2_PLL_OUT			273
+#define IMX8MQ_CLK_MU_ROOT			264
+#define IMX8MQ_VIDEO2_PLL_OUT			265
 
-#define IMX8MQ_CLK_CLKO2			274
+#define IMX8MQ_CLK_CLKO2			266
 
-#define IMX8MQ_CLK_NAND_USDHC_BUS_RAWNAND_CLK	275
+#define IMX8MQ_CLK_NAND_USDHC_BUS_RAWNAND_CLK	267
 
-#define IMX8MQ_CLK_END				276
+#define IMX8MQ_CLK_END				268
 #endif /* __DT_BINDINGS_CLOCK_IMX8MQ_H */