Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (119 commits)
  MIPS: Delete unused function add_temporary_entry.
  MIPS: Set default pci cache line size.
  MIPS: Flush huge TLB
  MIPS: Octeon: Remove SYS_SUPPORTS_HIGHMEM.
  MIPS: Octeon: Add support for OCTEON II PCIe
  MIPS: Octeon: Update PCI Latency timer and enable more error reporting.
  MIPS: Alchemy: Update cpu-feature-overrides
  MIPS: Alchemy: db1200: Improve PB1200 detection.
  MIPS: Alchemy: merge Au1000 and Au1300-style IRQ controller code.
  MIPS: Alchemy: chain IRQ controllers to MIPS IRQ controller
  MIPS: Alchemy: irq: register pm at irq init time
  MIPS: Alchemy: Touchscreen support on DB1100
  MIPS: Alchemy: Hook up IrDA on DB1000/DB1100
  net/irda: convert au1k_ir to platform driver.
  MIPS: Alchemy: remove unused board headers
  MTD: nand: make au1550nd.c a platform_driver
  MIPS: Netlogic: Mark Netlogic chips as SMT capable
  MIPS: Netlogic: Add support for XLP 3XX cores
  MIPS: Netlogic: Merge some of XLR/XLP wakup code
  MIPS: Netlogic: Add default XLP config.
  ...

Fix up trivial conflicts in arch/mips/kernel/{perf_event_mipsxx.c,
traps.c} and drivers/tty/serial/Makefile

arch/mips/Kconfig

@@ -719,7 +719,6 @@ config CAVIUM_OCTEON_SIMULATOR
 	select DMA_COHERENT
 	select SYS_SUPPORTS_64BIT_KERNEL
 	select SYS_SUPPORTS_BIG_ENDIAN
-	select SYS_SUPPORTS_HIGHMEM
 	select SYS_SUPPORTS_HOTPLUG_CPU
 	select SYS_HAS_CPU_CAVIUM_OCTEON
 	select HOLES_IN_ZONE
@@ -735,7 +734,6 @@ config CAVIUM_OCTEON_REFERENCE_BOARD
 	select DMA_COHERENT
 	select SYS_SUPPORTS_64BIT_KERNEL
 	select SYS_SUPPORTS_BIG_ENDIAN
-	select SYS_SUPPORTS_HIGHMEM
 	select SYS_SUPPORTS_HOTPLUG_CPU
 	select SYS_HAS_EARLY_PRINTK
 	select SYS_HAS_CPU_CAVIUM_OCTEON
@@ -764,7 +762,6 @@ config NLM_XLR_BOARD
 	depends on EXPERIMENTAL
 	select BOOT_ELF32
 	select NLM_COMMON
-	select NLM_XLR
 	select SYS_HAS_CPU_XLR
 	select SYS_SUPPORTS_SMP
 	select HW_HAS_PCI
@@ -779,6 +776,7 @@ config NLM_XLR_BOARD
 	select CEVT_R4K
 	select CSRC_R4K
 	select IRQ_CPU
+	select ARCH_SUPPORTS_MSI
 	select ZONE_DMA if 64BIT
 	select SYNC_R4K
 	select SYS_HAS_EARLY_PRINTK
@@ -786,6 +784,33 @@ config NLM_XLR_BOARD
 	  Support for systems based on Netlogic XLR and XLS processors.
 	  Say Y here if you have a XLR or XLS based board.
 
+config NLM_XLP_BOARD
+	bool "Netlogic XLP based systems"
+	depends on EXPERIMENTAL
+	select BOOT_ELF32
+	select NLM_COMMON
+	select SYS_HAS_CPU_XLP
+	select SYS_SUPPORTS_SMP
+	select HW_HAS_PCI
+	select SWAP_IO_SPACE
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_64BIT_KERNEL
+	select 64BIT_PHYS_ADDR
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_SUPPORTS_HIGHMEM
+	select DMA_COHERENT
+	select NR_CPUS_DEFAULT_32
+	select CEVT_R4K
+	select CSRC_R4K
+	select IRQ_CPU
+	select ZONE_DMA if 64BIT
+	select SYNC_R4K
+	select SYS_HAS_EARLY_PRINTK
+	help
+	  This board is based on Netlogic XLP Processor.
+	  Say Y here if you have a XLP based board.
+
 endchoice
 
 source "arch/mips/alchemy/Kconfig"
@@ -1416,51 +1441,36 @@ config CPU_CAVIUM_OCTEON
 config CPU_BMIPS3300
 	bool "BMIPS3300"
 	depends on SYS_HAS_CPU_BMIPS3300
-	select DMA_NONCOHERENT
-	select IRQ_CPU
-	select SWAP_IO_SPACE
-	select SYS_SUPPORTS_32BIT_KERNEL
-	select WEAK_ORDERING
+	select CPU_BMIPS
 	help
 	  Broadcom BMIPS3300 processors.
 
 config CPU_BMIPS4350
 	bool "BMIPS4350"
 	depends on SYS_HAS_CPU_BMIPS4350
-	select CPU_SUPPORTS_32BIT_KERNEL
-	select DMA_NONCOHERENT
-	select IRQ_CPU
-	select SWAP_IO_SPACE
+	select CPU_BMIPS
 	select SYS_SUPPORTS_SMP
 	select SYS_SUPPORTS_HOTPLUG_CPU
-	select WEAK_ORDERING
 	help
 	  Broadcom BMIPS4350 ("VIPER") processors.
 
 config CPU_BMIPS4380
 	bool "BMIPS4380"
 	depends on SYS_HAS_CPU_BMIPS4380
-	select CPU_SUPPORTS_32BIT_KERNEL
-	select DMA_NONCOHERENT
-	select IRQ_CPU
-	select SWAP_IO_SPACE
+	select CPU_BMIPS
 	select SYS_SUPPORTS_SMP
 	select SYS_SUPPORTS_HOTPLUG_CPU
-	select WEAK_ORDERING
 	help
 	  Broadcom BMIPS4380 processors.
 
 config CPU_BMIPS5000
 	bool "BMIPS5000"
 	depends on SYS_HAS_CPU_BMIPS5000
-	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_BMIPS
 	select CPU_SUPPORTS_HIGHMEM
-	select DMA_NONCOHERENT
-	select IRQ_CPU
-	select SWAP_IO_SPACE
+	select MIPS_CPU_SCACHE
 	select SYS_SUPPORTS_SMP
 	select SYS_SUPPORTS_HOTPLUG_CPU
-	select WEAK_ORDERING
 	help
 	  Broadcom BMIPS5000 processors.
 
@@ -1475,6 +1485,19 @@ config CPU_XLR
 	select CPU_SUPPORTS_HUGEPAGES
 	help
 	  Netlogic Microsystems XLR/XLS processors.
+
+config CPU_XLP
+	bool "Netlogic XLP SoC"
+	depends on SYS_HAS_CPU_XLP
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_64BIT_KERNEL
+	select CPU_SUPPORTS_HIGHMEM
+	select CPU_HAS_LLSC
+	select WEAK_ORDERING
+	select WEAK_REORDERING_BEYOND_LLSC
+	select CPU_HAS_PREFETCH
+	help
+	  Netlogic Microsystems XLP processors.
 endchoice
 
 if CPU_LOONGSON2F
@@ -1521,6 +1544,15 @@ config CPU_LOONGSON2
 	select CPU_SUPPORTS_64BIT_KERNEL
 	select CPU_SUPPORTS_HIGHMEM
 
+config CPU_BMIPS
+	bool
+	select CPU_MIPS32
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select DMA_NONCOHERENT
+	select IRQ_CPU
+	select SWAP_IO_SPACE
+	select WEAK_ORDERING
+
 config SYS_HAS_CPU_LOONGSON2E
 	bool
 
@@ -1608,6 +1640,9 @@ config SYS_HAS_CPU_BMIPS5000
 config SYS_HAS_CPU_XLR
 	bool
 
+config SYS_HAS_CPU_XLP
+	bool
+
 #
 # CPU may reorder R->R, R->W, W->R, W->W
 # Reordering beyond LL and SC is handled in WEAK_REORDERING_BEYOND_LLSC
@@ -1995,6 +2030,9 @@ config CPU_HAS_SMARTMIPS
 config CPU_HAS_WB
 	bool
 
+config XKS01
+	bool
+
 #
 # Vectored interrupt mode is an R2 feature
 #

arch/mips/Makefile

@@ -157,6 +157,7 @@ ifeq (,$(findstring march=octeon, $(cflags-$(CONFIG_CPU_CAVIUM_OCTEON))))
 cflags-$(CONFIG_CPU_CAVIUM_OCTEON) += -Wa,-march=octeon
 endif
 cflags-$(CONFIG_CAVIUM_CN63XXP1) += -Wa,-mfix-cn63xxp1
+cflags-$(CONFIG_CPU_BMIPS)	+= -march=mips32 -Wa,-mips32 -Wa,--trap
 
 cflags-$(CONFIG_CPU_R4000_WORKAROUNDS)	+= $(call cc-option,-mfix-r4000,)
 cflags-$(CONFIG_CPU_R4400_WORKAROUNDS)	+= $(call cc-option,-mfix-r4400,)

arch/mips/alchemy/Kconfig

@@ -2,6 +2,10 @@
 config ALCHEMY_GPIOINT_AU1000
 	bool
 
+# au1300-style GPIO/INT controller
+config ALCHEMY_GPIOINT_AU1300
+	bool
+
 # select this in your board config if you don't want to use the gpio
 # namespace as documented in the manuals.  In this case however you need
 # to create the necessary gpio_* functions in your board code/headers!
@@ -22,43 +26,29 @@ config MIPS_MTX1
 	select SYS_SUPPORTS_LITTLE_ENDIAN
 	select SYS_HAS_EARLY_PRINTK
 
-config MIPS_BOSPORUS
-	bool "Alchemy Bosporus board"
-	select ALCHEMY_GPIOINT_AU1000
-	select DMA_NONCOHERENT
-	select SYS_SUPPORTS_LITTLE_ENDIAN
-	select SYS_HAS_EARLY_PRINTK
-
 config MIPS_DB1000
-	bool "Alchemy DB1000 board"
+	bool "Alchemy DB1000/DB1500/DB1100 boards"
 	select ALCHEMY_GPIOINT_AU1000
 	select DMA_NONCOHERENT
 	select HW_HAS_PCI
-	select SYS_SUPPORTS_LITTLE_ENDIAN
-	select SYS_HAS_EARLY_PRINTK
-
-config MIPS_DB1100
-	bool "Alchemy DB1100 board"
-	select ALCHEMY_GPIOINT_AU1000
-	select DMA_NONCOHERENT
+	select MIPS_DISABLE_OBSOLETE_IDE
+	select SYS_SUPPORTS_BIG_ENDIAN
 	select SYS_SUPPORTS_LITTLE_ENDIAN
 	select SYS_HAS_EARLY_PRINTK
 
 config MIPS_DB1200
-	bool "Alchemy DB1200 board"
+	bool "Alchemy DB1200/PB1200 board"
 	select ALCHEMY_GPIOINT_AU1000
 	select DMA_COHERENT
 	select MIPS_DISABLE_OBSOLETE_IDE
 	select SYS_SUPPORTS_LITTLE_ENDIAN
 	select SYS_HAS_EARLY_PRINTK
 
-config MIPS_DB1500
-	bool "Alchemy DB1500 board"
-	select ALCHEMY_GPIOINT_AU1000
-	select DMA_NONCOHERENT
-	select HW_HAS_PCI
+config MIPS_DB1300
+	bool "NetLogic DB1300 board"
+	select ALCHEMY_GPIOINT_AU1300
+	select DMA_COHERENT
 	select MIPS_DISABLE_OBSOLETE_IDE
-	select SYS_SUPPORTS_BIG_ENDIAN
 	select SYS_SUPPORTS_LITTLE_ENDIAN
 	select SYS_HAS_EARLY_PRINTK
 
@@ -66,27 +56,11 @@ config MIPS_DB1550
 	bool "Alchemy DB1550 board"
 	select ALCHEMY_GPIOINT_AU1000
 	select HW_HAS_PCI
-	select DMA_NONCOHERENT
+	select DMA_COHERENT
 	select MIPS_DISABLE_OBSOLETE_IDE
 	select SYS_SUPPORTS_LITTLE_ENDIAN
 	select SYS_HAS_EARLY_PRINTK
 
-config MIPS_MIRAGE
-	bool "Alchemy Mirage board"
-	select DMA_NONCOHERENT
-	select ALCHEMY_GPIOINT_AU1000
-	select SYS_SUPPORTS_LITTLE_ENDIAN
-	select SYS_HAS_EARLY_PRINTK
-
-config MIPS_PB1000
-	bool "Alchemy PB1000 board"
-	select ALCHEMY_GPIOINT_AU1000
-	select DMA_NONCOHERENT
-	select HW_HAS_PCI
-	select SWAP_IO_SPACE
-	select SYS_SUPPORTS_LITTLE_ENDIAN
-	select SYS_HAS_EARLY_PRINTK
-
 config MIPS_PB1100
 	bool "Alchemy PB1100 board"
 	select ALCHEMY_GPIOINT_AU1000
@@ -96,14 +70,6 @@ config MIPS_PB1100
 	select SYS_SUPPORTS_LITTLE_ENDIAN
 	select SYS_HAS_EARLY_PRINTK
 
-config MIPS_PB1200
-	bool "Alchemy PB1200 board"
-	select ALCHEMY_GPIOINT_AU1000
-	select DMA_NONCOHERENT
-	select MIPS_DISABLE_OBSOLETE_IDE
-	select SYS_SUPPORTS_LITTLE_ENDIAN
-	select SYS_HAS_EARLY_PRINTK
-
 config MIPS_PB1500
 	bool "Alchemy PB1500 board"
 	select ALCHEMY_GPIOINT_AU1000

arch/mips/alchemy/Makefile

+obj-$(CONFIG_MIPS_GPR) += board-gpr.o
+obj-$(CONFIG_MIPS_MTX1) += board-mtx1.o
+obj-$(CONFIG_MIPS_XXS1500) += board-xxs1500.o

arch/mips/alchemy/Platform

@@ -4,62 +4,31 @@
 platform-$(CONFIG_MIPS_ALCHEMY)	+= alchemy/common/
 
 
-#
-# AMD Alchemy Pb1000 eval board
-#
-platform-$(CONFIG_MIPS_PB1000)	+= alchemy/devboards/
-cflags-$(CONFIG_MIPS_PB1000)	+= -I$(srctree)/arch/mips/include/asm/mach-pb1x00
-load-$(CONFIG_MIPS_PB1000)	+= 0xffffffff80100000
-
 #
 # AMD Alchemy Pb1100 eval board
 #
 platform-$(CONFIG_MIPS_PB1100)	+= alchemy/devboards/
-cflags-$(CONFIG_MIPS_PB1100)	+= -I$(srctree)/arch/mips/include/asm/mach-pb1x00
 load-$(CONFIG_MIPS_PB1100)	+= 0xffffffff80100000
 
 #
 # AMD Alchemy Pb1500 eval board
 #
 platform-$(CONFIG_MIPS_PB1500)	+= alchemy/devboards/
-cflags-$(CONFIG_MIPS_PB1500)	+= -I$(srctree)/arch/mips/include/asm/mach-pb1x00
 load-$(CONFIG_MIPS_PB1500)	+= 0xffffffff80100000
 
 #
 # AMD Alchemy Pb1550 eval board
 #
 platform-$(CONFIG_MIPS_PB1550)	+= alchemy/devboards/
-cflags-$(CONFIG_MIPS_PB1550)	+= -I$(srctree)/arch/mips/include/asm/mach-pb1x00
 load-$(CONFIG_MIPS_PB1550)	+= 0xffffffff80100000
 
 #
-# AMD Alchemy Pb1200 eval board
-#
-platform-$(CONFIG_MIPS_PB1200)	+= alchemy/devboards/
-cflags-$(CONFIG_MIPS_PB1200)	+= -I$(srctree)/arch/mips/include/asm/mach-pb1x00
-load-$(CONFIG_MIPS_PB1200)	+= 0xffffffff80100000
-
-#
-# AMD Alchemy Db1000 eval board
+# AMD Alchemy Db1000/Db1500/Db1100 eval boards
 #
 platform-$(CONFIG_MIPS_DB1000)	+= alchemy/devboards/
 cflags-$(CONFIG_MIPS_DB1000)	+= -I$(srctree)/arch/mips/include/asm/mach-db1x00
 load-$(CONFIG_MIPS_DB1000)	+= 0xffffffff80100000
 
-#
-# AMD Alchemy Db1100 eval board
-#
-platform-$(CONFIG_MIPS_DB1100)	+= alchemy/devboards/
-cflags-$(CONFIG_MIPS_DB1100)	+= -I$(srctree)/arch/mips/include/asm/mach-db1x00
-load-$(CONFIG_MIPS_DB1100)	+= 0xffffffff80100000
-
-#
-# AMD Alchemy Db1500 eval board
-#
-platform-$(CONFIG_MIPS_DB1500)	+= alchemy/devboards/
-cflags-$(CONFIG_MIPS_DB1500)	+= -I$(srctree)/arch/mips/include/asm/mach-db1x00
-load-$(CONFIG_MIPS_DB1500)	+= 0xffffffff80100000
-
 #
 # AMD Alchemy Db1550 eval board
 #
@@ -68,42 +37,35 @@ cflags-$(CONFIG_MIPS_DB1550)	+= -I$(srctree)/arch/mips/include/asm/mach-db1x00
 load-$(CONFIG_MIPS_DB1550)	+= 0xffffffff80100000
 
 #
-# AMD Alchemy Db1200 eval board
+# AMD Alchemy Db1200/Pb1200 eval boards
 #
 platform-$(CONFIG_MIPS_DB1200)	+= alchemy/devboards/
 cflags-$(CONFIG_MIPS_DB1200)	+= -I$(srctree)/arch/mips/include/asm/mach-db1x00
 load-$(CONFIG_MIPS_DB1200)	+= 0xffffffff80100000
 
 #
-# AMD Alchemy Bosporus eval board
-#
-platform-$(CONFIG_MIPS_BOSPORUS) += alchemy/devboards/
-cflags-$(CONFIG_MIPS_BOSPORUS)	 += -I$(srctree)/arch/mips/include/asm/mach-db1x00
-load-$(CONFIG_MIPS_BOSPORUS)	 += 0xffffffff80100000
-
-#
-# AMD Alchemy Mirage eval board
+# NetLogic DBAu1300 development platform
 #
-platform-$(CONFIG_MIPS_MIRAGE)	+= alchemy/devboards/
-cflags-$(CONFIG_MIPS_MIRAGE)	+= -I$(srctree)/arch/mips/include/asm/mach-db1x00
-load-$(CONFIG_MIPS_MIRAGE)	+= 0xffffffff80100000
+platform-$(CONFIG_MIPS_DB1300)	+= alchemy/devboards/
+cflags-$(CONFIG_MIPS_DB1300)	+= -I$(srctree)/arch/mips/include/asm/mach-db1x00
+load-$(CONFIG_MIPS_DB1300)	+= 0xffffffff80100000
 
 #
-# 4G-Systems eval board
+# 4G-Systems MTX-1 "MeshCube" wireless router
 #
-platform-$(CONFIG_MIPS_MTX1)	+= alchemy/mtx-1/
+platform-$(CONFIG_MIPS_MTX1)	+= alchemy/
 load-$(CONFIG_MIPS_MTX1)	+= 0xffffffff80100000
 
 #
 # MyCable eval board
 #
-platform-$(CONFIG_MIPS_XXS1500)	+= alchemy/xxs1500/
+platform-$(CONFIG_MIPS_XXS1500)	+= alchemy/
 load-$(CONFIG_MIPS_XXS1500)	+= 0xffffffff80100000
 
 #
 # Trapeze ITS GRP board
 #
-platform-$(CONFIG_MIPS_GPR)	+= alchemy/gpr/
+platform-$(CONFIG_MIPS_GPR)	+= alchemy/
 load-$(CONFIG_MIPS_GPR)		+= 0xffffffff80100000
 
 # boards can specify their own <gpio.h> in one of their include dirs.

arch/mips/alchemy/gpr/platform.c → arch/mips/alchemy/board-gpr.c

 /*
- * GPR board platform device registration
+ * GPR board platform device registration (Au1550)
  *
  * Copyright (C) 2010 Wolfgang Grandegger <wg@denx.de>
  *
@@ -18,16 +18,89 @@
  * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
  */
 
+#include <linux/delay.h>
 #include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
 #include <linux/platform_device.h>
+#include <linux/pm.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/physmap.h>
 #include <linux/leds.h>
 #include <linux/gpio.h>
 #include <linux/i2c.h>
 #include <linux/i2c-gpio.h>
-
+#include <asm/bootinfo.h>
+#include <asm/reboot.h>
 #include <asm/mach-au1x00/au1000.h>
+#include <prom.h>
+
+const char *get_system_type(void)
+{
+	return "GPR";
+}
+
+void __init prom_init(void)
+{
+	unsigned char *memsize_str;
+	unsigned long memsize;
+
+	prom_argc = fw_arg0;
+	prom_argv = (char **)fw_arg1;
+	prom_envp = (char **)fw_arg2;
+
+	prom_init_cmdline();
+
+	memsize_str = prom_getenv("memsize");
+	if (!memsize_str)
+		memsize = 0x04000000;
+	else
+		strict_strtoul(memsize_str, 0, &memsize);
+	add_memory_region(0, memsize, BOOT_MEM_RAM);
+}
+
+void prom_putchar(unsigned char c)
+{
+	alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
+}
+
+static void gpr_reset(char *c)
+{
+	/* switch System-LED to orange (red# and green# on) */
+	alchemy_gpio_direction_output(4, 0);
+	alchemy_gpio_direction_output(5, 0);
+
+	/* trigger watchdog to reset board in 200ms */
+	printk(KERN_EMERG "Triggering watchdog soft reset...\n");
+	raw_local_irq_disable();
+	alchemy_gpio_direction_output(1, 0);
+	udelay(1);
+	alchemy_gpio_set_value(1, 1);
+	while (1)
+		cpu_wait();
+}
+
+static void gpr_power_off(void)
+{
+	while (1)
+		cpu_wait();
+}
+
+void __init board_setup(void)
+{
+	printk(KERN_INFO "Trapeze ITS GPR board\n");
+
+	pm_power_off = gpr_power_off;
+	_machine_halt = gpr_power_off;
+	_machine_restart = gpr_reset;
+
+	/* Enable UART1/3 */
+	alchemy_uart_enable(AU1000_UART3_PHYS_ADDR);
+	alchemy_uart_enable(AU1000_UART1_PHYS_ADDR);
+
+	/* Take away Reset of UMTS-card */
+	alchemy_gpio_direction_output(215, 1);
+}
 
 /*
  * Watchdog
@@ -152,7 +225,7 @@ static struct i2c_gpio_platform_data gpr_i2c_data = {
 	.scl_is_open_drain	= 1,
 	.udelay			= 2,		/* ~100 kHz */
 	.timeout		= HZ,
- };
+};
 
 static struct platform_device gpr_i2c_device = {
 	.name			= "i2c-gpio",
@@ -184,7 +257,7 @@ static int gpr_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
 	else if ((slot == 0) && (pin == 2))
 		return AU1550_PCI_INTB;
 
-	return -1;
+	return 0xff;
 }
 
 static struct alchemy_pci_platdata gpr_pci_pd = {

arch/mips/alchemy/mtx-1/platform.c → arch/mips/alchemy/board-mtx1.c

 /*
- * MTX-1 platform devices registration
+ * MTX-1 platform devices registration (Au1500)
  *
  * Copyright (C) 2007-2009, Florian Fainelli <florian@openwrt.org>
  *
@@ -19,6 +19,8 @@
  */
 
 #include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
 #include <linux/platform_device.h>
 #include <linux/leds.h>
 #include <linux/gpio.h>
@@ -27,8 +29,85 @@
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/physmap.h>
 #include <mtd/mtd-abi.h>
-
+#include <asm/bootinfo.h>
+#include <asm/reboot.h>
+#include <asm/mach-au1x00/au1000.h>
 #include <asm/mach-au1x00/au1xxx_eth.h>
+#include <prom.h>
+
+const char *get_system_type(void)
+{
+	return "MTX-1";
+}
+
+void __init prom_init(void)
+{
+	unsigned char *memsize_str;
+	unsigned long memsize;
+
+	prom_argc = fw_arg0;
+	prom_argv = (char **)fw_arg1;
+	prom_envp = (char **)fw_arg2;
+
+	prom_init_cmdline();
+
+	memsize_str = prom_getenv("memsize");
+	if (!memsize_str)
+		memsize = 0x04000000;
+	else
+		strict_strtoul(memsize_str, 0, &memsize);
+	add_memory_region(0, memsize, BOOT_MEM_RAM);
+}
+
+void prom_putchar(unsigned char c)
+{
+	alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
+}
+
+static void mtx1_reset(char *c)
+{
+	/* Jump to the reset vector */
+	__asm__ __volatile__("jr\t%0" : : "r"(0xbfc00000));
+}
+
+static void mtx1_power_off(void)
+{
+	while (1)
+		asm volatile (
+		"	.set	mips32					\n"
+		"	wait						\n"
+		"	.set	mips0					\n");
+}
+
+void __init board_setup(void)
+{
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+	/* Enable USB power switch */
+	alchemy_gpio_direction_output(204, 0);
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
+
+	/* Initialize sys_pinfunc */
+	au_writel(SYS_PF_NI2, SYS_PINFUNC);
+
+	/* Initialize GPIO */
+	au_writel(~0, KSEG1ADDR(AU1000_SYS_PHYS_ADDR) + SYS_TRIOUTCLR);
+	alchemy_gpio_direction_output(0, 0);	/* Disable M66EN (PCI 66MHz) */
+	alchemy_gpio_direction_output(3, 1);	/* Disable PCI CLKRUN# */
+	alchemy_gpio_direction_output(1, 1);	/* Enable EXT_IO3 */
+	alchemy_gpio_direction_output(5, 0);	/* Disable eth PHY TX_ER */
+
+	/* Enable LED and set it to green */
+	alchemy_gpio_direction_output(211, 1);	/* green on */
+	alchemy_gpio_direction_output(212, 0);	/* red off */
+
+	pm_power_off = mtx1_power_off;
+	_machine_halt = mtx1_power_off;
+	_machine_restart = mtx1_reset;
+
+	printk(KERN_INFO "4G Systems MTX-1 Board\n");
+}
+
+/******************************************************************************/
 
 static struct gpio_keys_button mtx1_gpio_button[] = {
 	{
@@ -195,7 +274,6 @@ static struct platform_device mtx1_pci_host = {
 	.resource	= alchemy_pci_host_res,
 };
 
-
 static struct __initdata platform_device * mtx1_devs[] = {
 	&mtx1_pci_host,
 	&mtx1_gpio_leds,
@@ -213,6 +291,12 @@ static int __init mtx1_register_devices(void)
 {
 	int rc;
 
+	irq_set_irq_type(AU1500_GPIO204_INT, IRQ_TYPE_LEVEL_HIGH);
+	irq_set_irq_type(AU1500_GPIO201_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO202_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO203_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO205_INT, IRQ_TYPE_LEVEL_LOW);
+
 	au1xxx_override_eth_cfg(0, &mtx1_au1000_eth0_pdata);
 
 	rc = gpio_request(mtx1_gpio_button[0].gpio,
@@ -226,5 +310,4 @@ static int __init mtx1_register_devices(void)
 out:
 	return platform_add_devices(mtx1_devs, ARRAY_SIZE(mtx1_devs));
 }
-
 arch_initcall(mtx1_register_devices);

arch/mips/alchemy/xxs1500/platform.c → arch/mips/alchemy/board-xxs1500.c

 /*
- * XXS1500 board platform device registration
+ * BRIEF MODULE DESCRIPTION
+ *	MyCable XXS1500 board support
  *
- * Copyright (C) 2009 Manuel Lauss
+ * Copyright 2003, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
@@ -18,10 +20,85 @@
  * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
  */
 
+#include <linux/kernel.h>
 #include <linux/init.h>
+#include <linux/interrupt.h>
 #include <linux/platform_device.h>
-
+#include <linux/gpio.h>
+#include <linux/delay.h>
+#include <linux/pm.h>
+#include <asm/bootinfo.h>
+#include <asm/reboot.h>
 #include <asm/mach-au1x00/au1000.h>
+#include <prom.h>
+
+const char *get_system_type(void)
+{
+	return "XXS1500";
+}
+
+void __init prom_init(void)
+{
+	unsigned char *memsize_str;
+	unsigned long memsize;
+
+	prom_argc = fw_arg0;
+	prom_argv = (char **)fw_arg1;
+	prom_envp = (char **)fw_arg2;
+
+	prom_init_cmdline();
+
+	memsize_str = prom_getenv("memsize");
+	if (!memsize_str || strict_strtoul(memsize_str, 0, &memsize))
+		memsize = 0x04000000;
+
+	add_memory_region(0, memsize, BOOT_MEM_RAM);
+}
+
+void prom_putchar(unsigned char c)
+{
+	alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
+}
+
+static void xxs1500_reset(char *c)
+{
+	/* Jump to the reset vector */
+	__asm__ __volatile__("jr\t%0" : : "r"(0xbfc00000));
+}
+
+static void xxs1500_power_off(void)
+{
+	while (1)
+		asm volatile (
+		"	.set	mips32					\n"
+		"	wait						\n"
+		"	.set	mips0					\n");
+}
+
+void __init board_setup(void)
+{
+	u32 pin_func;
+
+	pm_power_off = xxs1500_power_off;
+	_machine_halt = xxs1500_power_off;
+	_machine_restart = xxs1500_reset;
+
+	alchemy_gpio1_input_enable();
+	alchemy_gpio2_enable();
+
+	/* Set multiple use pins (UART3/GPIO) to UART (it's used as UART too) */
+	pin_func  = au_readl(SYS_PINFUNC) & ~SYS_PF_UR3;
+	pin_func |= SYS_PF_UR3;
+	au_writel(pin_func, SYS_PINFUNC);
+
+	/* Enable UART */
+	alchemy_uart_enable(AU1000_UART3_PHYS_ADDR);
+	/* Enable DTR (MCR bit 0) = USB power up */
+	__raw_writel(1, (void __iomem *)KSEG1ADDR(AU1000_UART3_PHYS_ADDR + 0x18));
+	wmb();
+}
+
+/******************************************************************************/
 
 static struct resource xxs1500_pcmcia_res[] = {
 	{
@@ -57,6 +134,20 @@ static struct platform_device *xxs1500_devs[] __initdata = {
 
 static int __init xxs1500_dev_init(void)
 {
+	irq_set_irq_type(AU1500_GPIO204_INT, IRQ_TYPE_LEVEL_HIGH);
+	irq_set_irq_type(AU1500_GPIO201_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO202_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO203_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO205_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO207_INT, IRQ_TYPE_LEVEL_LOW);
+
+	irq_set_irq_type(AU1500_GPIO0_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO1_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO2_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO3_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO4_INT, IRQ_TYPE_LEVEL_LOW); /* CF irq */
+	irq_set_irq_type(AU1500_GPIO5_INT, IRQ_TYPE_LEVEL_LOW);
+
 	return platform_add_devices(xxs1500_devs,
 				    ARRAY_SIZE(xxs1500_devs));
 }

arch/mips/alchemy/common/Makefile

@@ -6,9 +6,7 @@
 #
 
 obj-y += prom.o time.o clocks.o platform.o power.o setup.o \
-	sleeper.o dma.o dbdma.o
-
-obj-$(CONFIG_ALCHEMY_GPIOINT_AU1000) += irq.o
+	sleeper.o dma.o dbdma.o vss.o irq.o
 
 # optional gpiolib support
 ifeq ($(CONFIG_ALCHEMY_GPIO_INDIRECT),)

arch/mips/alchemy/common/dbdma.c

@@ -148,6 +148,50 @@ static dbdev_tab_t au1200_dbdev_tab[] __initdata = {
 	{ DSCR_CMD0_ALWAYS,   DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
 };
 
+static dbdev_tab_t au1300_dbdev_tab[] __initdata = {
+	{ AU1300_DSCR_CMD0_UART0_TX, DEV_FLAGS_OUT, 0, 8,  0x10100004, 0, 0 },
+	{ AU1300_DSCR_CMD0_UART0_RX, DEV_FLAGS_IN,  0, 8,  0x10100000, 0, 0 },
+	{ AU1300_DSCR_CMD0_UART1_TX, DEV_FLAGS_OUT, 0, 8,  0x10101004, 0, 0 },
+	{ AU1300_DSCR_CMD0_UART1_RX, DEV_FLAGS_IN,  0, 8,  0x10101000, 0, 0 },
+	{ AU1300_DSCR_CMD0_UART2_TX, DEV_FLAGS_OUT, 0, 8,  0x10102004, 0, 0 },
+	{ AU1300_DSCR_CMD0_UART2_RX, DEV_FLAGS_IN,  0, 8,  0x10102000, 0, 0 },
+	{ AU1300_DSCR_CMD0_UART3_TX, DEV_FLAGS_OUT, 0, 8,  0x10103004, 0, 0 },
+	{ AU1300_DSCR_CMD0_UART3_RX, DEV_FLAGS_IN,  0, 8,  0x10103000, 0, 0 },
+
+	{ AU1300_DSCR_CMD0_SDMS_TX0, DEV_FLAGS_OUT, 4, 8,  0x10600000, 0, 0 },
+	{ AU1300_DSCR_CMD0_SDMS_RX0, DEV_FLAGS_IN,  4, 8,  0x10600004, 0, 0 },
+	{ AU1300_DSCR_CMD0_SDMS_TX1, DEV_FLAGS_OUT, 8, 8,  0x10601000, 0, 0 },
+	{ AU1300_DSCR_CMD0_SDMS_RX1, DEV_FLAGS_IN,  8, 8,  0x10601004, 0, 0 },
+
+	{ AU1300_DSCR_CMD0_AES_RX, DEV_FLAGS_IN ,   4, 32, 0x10300008, 0, 0 },
+	{ AU1300_DSCR_CMD0_AES_TX, DEV_FLAGS_OUT,   4, 32, 0x10300004, 0, 0 },
+
+	{ AU1300_DSCR_CMD0_PSC0_TX, DEV_FLAGS_OUT,  0, 16, 0x10a0001c, 0, 0 },
+	{ AU1300_DSCR_CMD0_PSC0_RX, DEV_FLAGS_IN,   0, 16, 0x10a0001c, 0, 0 },
+	{ AU1300_DSCR_CMD0_PSC1_TX, DEV_FLAGS_OUT,  0, 16, 0x10a0101c, 0, 0 },
+	{ AU1300_DSCR_CMD0_PSC1_RX, DEV_FLAGS_IN,   0, 16, 0x10a0101c, 0, 0 },
+	{ AU1300_DSCR_CMD0_PSC2_TX, DEV_FLAGS_OUT,  0, 16, 0x10a0201c, 0, 0 },
+	{ AU1300_DSCR_CMD0_PSC2_RX, DEV_FLAGS_IN,   0, 16, 0x10a0201c, 0, 0 },
+	{ AU1300_DSCR_CMD0_PSC3_TX, DEV_FLAGS_OUT,  0, 16, 0x10a0301c, 0, 0 },
+	{ AU1300_DSCR_CMD0_PSC3_RX, DEV_FLAGS_IN,   0, 16, 0x10a0301c, 0, 0 },
+
+	{ AU1300_DSCR_CMD0_LCD, DEV_FLAGS_ANYUSE,   0, 0,  0x00000000, 0, 0 },
+	{ AU1300_DSCR_CMD0_NAND_FLASH, DEV_FLAGS_IN, 0, 0, 0x00000000, 0, 0 },
+
+	{ AU1300_DSCR_CMD0_SDMS_TX2, DEV_FLAGS_OUT, 4, 8,  0x10602000, 0, 0 },
+	{ AU1300_DSCR_CMD0_SDMS_RX2, DEV_FLAGS_IN,  4, 8,  0x10602004, 0, 0 },
+
+	{ AU1300_DSCR_CMD0_CIM_SYNC, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+
+	{ AU1300_DSCR_CMD0_UDMA, DEV_FLAGS_ANYUSE,  0, 32, 0x14001810, 0, 0 },
+
+	{ AU1300_DSCR_CMD0_DMA_REQ0, 0, 0, 0, 0x00000000, 0, 0 },
+	{ AU1300_DSCR_CMD0_DMA_REQ1, 0, 0, 0, 0x00000000, 0, 0 },
+
+	{ DSCR_CMD0_THROTTLE, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+	{ DSCR_CMD0_ALWAYS,   DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+};
+
 /* 32 predefined plus 32 custom */
 #define DBDEV_TAB_SIZE		64
 
@@ -1019,8 +1063,7 @@ static int __init dbdma_setup(unsigned int irq, dbdev_tab_t *idtable)
 	dbdma_gptr->ddma_inten = 0xffff;
 	au_sync();
 
-	ret = request_irq(irq, dbdma_interrupt, IRQF_DISABLED, "dbdma",
-			  (void *)dbdma_gptr);
+	ret = request_irq(irq, dbdma_interrupt, 0, "dbdma", (void *)dbdma_gptr);
 	if (ret)
 		printk(KERN_ERR "Cannot grab DBDMA interrupt!\n");
 	else {
@@ -1038,6 +1081,8 @@ static int __init alchemy_dbdma_init(void)
 		return dbdma_setup(AU1550_DDMA_INT, au1550_dbdev_tab);
 	case ALCHEMY_CPU_AU1200:
 		return dbdma_setup(AU1200_DDMA_INT, au1200_dbdev_tab);
+	case ALCHEMY_CPU_AU1300:
+		return dbdma_setup(AU1300_DDMA_INT, au1300_dbdev_tab);
 	}
 	return 0;
 }

arch/mips/alchemy/common/gpiolib.c

@@ -27,6 +27,7 @@
  *	 CONFIG_ALCHEMY_GPIO_INDIRECT=n, otherwise compilation will fail!
  *	au1000 SoC have only one GPIO block : GPIO1
  *	Au1100, Au15x0, Au12x0 have a second one : GPIO2
+ *	Au1300 is totally different: 1 block with up to 128 GPIOs
  */
 
 #include <linux/init.h>
@@ -35,6 +36,7 @@
 #include <linux/types.h>
 #include <linux/gpio.h>
 #include <asm/mach-au1x00/gpio-au1000.h>
+#include <asm/mach-au1x00/gpio-au1300.h>
 
 static int gpio2_get(struct gpio_chip *chip, unsigned offset)
 {
@@ -115,6 +117,43 @@ struct gpio_chip alchemy_gpio_chip[] = {
 	},
 };
 
+static int alchemy_gpic_get(struct gpio_chip *chip, unsigned int off)
+{
+	return au1300_gpio_get_value(off + AU1300_GPIO_BASE);
+}
+
+static void alchemy_gpic_set(struct gpio_chip *chip, unsigned int off, int v)
+{
+	au1300_gpio_set_value(off + AU1300_GPIO_BASE, v);
+}
+
+static int alchemy_gpic_dir_input(struct gpio_chip *chip, unsigned int off)
+{
+	return au1300_gpio_direction_input(off + AU1300_GPIO_BASE);
+}
+
+static int alchemy_gpic_dir_output(struct gpio_chip *chip, unsigned int off,
+				   int v)
+{
+	return au1300_gpio_direction_output(off + AU1300_GPIO_BASE, v);
+}
+
+static int alchemy_gpic_gpio_to_irq(struct gpio_chip *chip, unsigned int off)
+{
+	return au1300_gpio_to_irq(off + AU1300_GPIO_BASE);
+}
+
+static struct gpio_chip au1300_gpiochip = {
+	.label			= "alchemy-gpic",
+	.direction_input	= alchemy_gpic_dir_input,
+	.direction_output	= alchemy_gpic_dir_output,
+	.get			= alchemy_gpic_get,
+	.set			= alchemy_gpic_set,
+	.to_irq			= alchemy_gpic_gpio_to_irq,
+	.base			= AU1300_GPIO_BASE,
+	.ngpio			= AU1300_GPIO_NUM,
+};
+
 static int __init alchemy_gpiochip_init(void)
 {
 	int ret = 0;
@@ -127,6 +166,9 @@ static int __init alchemy_gpiochip_init(void)
 		ret = gpiochip_add(&alchemy_gpio_chip[0]);
 		ret |= gpiochip_add(&alchemy_gpio_chip[1]);
 		break;
+	case ALCHEMY_CPU_AU1300:
+		ret = gpiochip_add(&au1300_gpiochip);
+		break;
 	}
 	return ret;
 }

arch/mips/alchemy/common/platform.c

@@ -82,6 +82,12 @@ static struct plat_serial8250_port au1x00_uart_data[][4] __initdata = {
 		PORT(AU1000_UART0_PHYS_ADDR, AU1200_UART0_INT),
 		PORT(AU1000_UART1_PHYS_ADDR, AU1200_UART1_INT),
 	},
+	[ALCHEMY_CPU_AU1300] = {
+		PORT(AU1300_UART0_PHYS_ADDR, AU1300_UART0_INT),
+		PORT(AU1300_UART1_PHYS_ADDR, AU1300_UART1_INT),
+		PORT(AU1300_UART2_PHYS_ADDR, AU1300_UART2_INT),
+		PORT(AU1300_UART3_PHYS_ADDR, AU1300_UART3_INT),
+	},
 };
 
 static struct platform_device au1xx0_uart_device = {
@@ -122,10 +128,12 @@ static unsigned long alchemy_ohci_data[][2] __initdata = {
 	[ALCHEMY_CPU_AU1100] = { AU1000_USB_OHCI_PHYS_ADDR, AU1100_USB_HOST_INT },
 	[ALCHEMY_CPU_AU1550] = { AU1550_USB_OHCI_PHYS_ADDR, AU1550_USB_HOST_INT },
 	[ALCHEMY_CPU_AU1200] = { AU1200_USB_OHCI_PHYS_ADDR, AU1200_USB_INT },
+	[ALCHEMY_CPU_AU1300] = { AU1300_USB_OHCI0_PHYS_ADDR, AU1300_USB_INT },
 };
 
 static unsigned long alchemy_ehci_data[][2] __initdata = {
 	[ALCHEMY_CPU_AU1200] = { AU1200_USB_EHCI_PHYS_ADDR, AU1200_USB_INT },
+	[ALCHEMY_CPU_AU1300] = { AU1300_USB_EHCI_PHYS_ADDR, AU1300_USB_INT },
 };
 
 static int __init _new_usbres(struct resource **r, struct platform_device **d)
@@ -169,8 +177,8 @@ static void __init alchemy_setup_usb(int ctype)
 		printk(KERN_INFO "Alchemy USB: cannot add OHCI0\n");
 
 
-	/* setup EHCI0: Au1200 */
-	if (ctype == ALCHEMY_CPU_AU1200) {
+	/* setup EHCI0: Au1200/Au1300 */
+	if ((ctype == ALCHEMY_CPU_AU1200) || (ctype == ALCHEMY_CPU_AU1300)) {
 		if (_new_usbres(&res, &pdev))
 			return;
 
@@ -187,6 +195,25 @@ static void __init alchemy_setup_usb(int ctype)
 		if (platform_device_register(pdev))
 			printk(KERN_INFO "Alchemy USB: cannot add EHCI0\n");
 	}
+
+	/* Au1300: OHCI1 */
+	if (ctype == ALCHEMY_CPU_AU1300) {
+		if (_new_usbres(&res, &pdev))
+			return;
+
+		res[0].start = AU1300_USB_OHCI1_PHYS_ADDR;
+		res[0].end = res[0].start + 0x100 - 1;
+		res[0].flags = IORESOURCE_MEM;
+		res[1].start = AU1300_USB_INT;
+		res[1].end = res[1].start;
+		res[1].flags = IORESOURCE_IRQ;
+		pdev->name = "au1xxx-ohci";
+		pdev->id = 1;
+		pdev->dev.dma_mask = &alchemy_ohci_dmamask;
+
+		if (platform_device_register(pdev))
+			printk(KERN_INFO "Alchemy USB: cannot add OHCI1\n");
+	}
 }
 
 /* Macro to help defining the Ethernet MAC resources */

arch/mips/alchemy/common/power.c

@@ -126,6 +126,9 @@ void au_sleep(void)
 	case ALCHEMY_CPU_AU1200:
 		alchemy_sleep_au1550();
 		break;
+	case ALCHEMY_CPU_AU1300:
+		alchemy_sleep_au1300();
+		break;
 	}
 
 	restore_core_regs();

arch/mips/alchemy/common/sleeper.S

@@ -153,6 +153,79 @@ LEAF(alchemy_sleep_au1550)
 
 END(alchemy_sleep_au1550)
 
+/* sleepcode for Au1300 memory controller type */
+LEAF(alchemy_sleep_au1300)
+
+	SETUP_SLEEP
+
+	/* cache following instructions, as memory gets put to sleep */
+	la	t0, 2f
+	la	t1, 4f
+	subu	t2, t1, t0
+
+	.set	mips3
+
+1:	cache	0x14, 0(t0)
+	subu	t2, t2, 32
+	bgez	t2, 1b
+	 addu	t0, t0, 32
+
+	.set	mips0
+
+2:	lui	a0, 0xb400		/* mem_xxx */
+
+	/* disable all ports in mem_sdportcfga */
+	sw	zero, 0x868(a0)		/* mem_sdportcfga */
+	sync
+
+	/* disable ODT */
+	li	t0, 0x03010000
+	sw	t0, 0x08d8(a0)		/* mem_sdcmd0 */
+	sw	t0, 0x08dc(a0)		/* mem_sdcmd1 */
+	sync
+
+	/* precharge */
+	li	t0, 0x23000400
+	sw	t0, 0x08dc(a0)		/* mem_sdcmd1 */
+	sw	t0, 0x08d8(a0)		/* mem_sdcmd0 */
+	sync
+
+	/* auto refresh */
+	sw	zero, 0x08c8(a0)	/* mem_sdautoref */
+	sync
+
+	/* block access to the DDR */
+	lw	t0, 0x0848(a0)		/* mem_sdconfigb */
+	li	t1, (1 << 7 | 0x3F)
+	or	t0, t0, t1
+	sw	t0, 0x0848(a0)		/* mem_sdconfigb */
+	sync
+
+	/* issue the Self Refresh command */
+	li	t0, 0x10000000
+	sw	t0, 0x08dc(a0)		/* mem_sdcmd1 */
+	sw	t0, 0x08d8(a0)		/* mem_sdcmd0 */
+	sync
+
+	/* wait for sdram to enter self-refresh mode */
+	lui	t0, 0x0300
+3:	lw	t1, 0x0850(a0)		/* mem_sdstat */
+	and	t2, t1, t0
+	bne	t2, t0, 3b
+	 nop
+
+	/* disable SDRAM clocks */
+	li	t0, ~(3<<28)
+	lw	t1, 0x0840(a0)		/* mem_sdconfiga */
+	and	t1, t1, t0		/* clear CE[1:0] */
+	sw	t1, 0x0840(a0)		/* mem_sdconfiga */
+	sync
+
+	DO_SLEEP
+4:
+
+END(alchemy_sleep_au1300)
+
 
 	/* This is where we return upon wakeup.
 	 * Reload all of the registers and return.

arch/mips/alchemy/common/time.c

@@ -92,7 +92,7 @@ static struct clock_event_device au1x_rtcmatch2_clockdev = {
 
 static struct irqaction au1x_rtcmatch2_irqaction = {
 	.handler	= au1x_rtcmatch2_irq,
-	.flags		= IRQF_DISABLED | IRQF_TIMER,
+	.flags		= IRQF_TIMER,
 	.name		= "timer",
 	.dev_id		= &au1x_rtcmatch2_clockdev,
 };
@@ -178,6 +178,7 @@ static int alchemy_m2inttab[] __initdata = {
 	AU1100_RTC_MATCH2_INT,
 	AU1550_RTC_MATCH2_INT,
 	AU1200_RTC_MATCH2_INT,
+	AU1300_RTC_MATCH2_INT,
 };
 
 void __init plat_time_init(void)

arch/mips/alchemy/common/vss.c

+/*
+ * Au1300 media block power gating (VSS)
+ *
+ * This is a stop-gap solution until I have the clock framework integration
+ * ready. This stuff here really must be handled transparently when clocks
+ * for various media blocks are enabled/disabled.
+ */
+
+#include <linux/module.h>
+#include <linux/spinlock.h>
+#include <asm/mach-au1x00/au1000.h>
+
+#define VSS_GATE	0x00	/* gate wait timers */
+#define VSS_CLKRST	0x04	/* clock/block control */
+#define VSS_FTR		0x08	/* footers */
+
+#define VSS_ADDR(blk)	(KSEG1ADDR(AU1300_VSS_PHYS_ADDR) + (blk * 0x0c))
+
+static DEFINE_SPINLOCK(au1300_vss_lock);
+
+/* enable a block as outlined in the databook */
+static inline void __enable_block(int block)
+{
+	void __iomem *base = (void __iomem *)VSS_ADDR(block);
+
+	__raw_writel(3, base + VSS_CLKRST);	/* enable clock, assert reset */
+	wmb();
+
+	__raw_writel(0x01fffffe, base + VSS_GATE); /* maximum setup time */
+	wmb();
+
+	/* enable footers in sequence */
+	__raw_writel(0x01, base + VSS_FTR);
+	wmb();
+	__raw_writel(0x03, base + VSS_FTR);
+	wmb();
+	__raw_writel(0x07, base + VSS_FTR);
+	wmb();
+	__raw_writel(0x0f, base + VSS_FTR);
+	wmb();
+
+	__raw_writel(0x01ffffff, base + VSS_GATE); /* start FSM too */
+	wmb();
+
+	__raw_writel(2, base + VSS_CLKRST);	/* deassert reset */
+	wmb();
+
+	__raw_writel(0x1f, base + VSS_FTR);	/* enable isolation cells */
+	wmb();
+}
+
+/* disable a block as outlined in the databook */
+static inline void __disable_block(int block)
+{
+	void __iomem *base = (void __iomem *)VSS_ADDR(block);
+
+	__raw_writel(0x0f, base + VSS_FTR);	/* disable isolation cells */
+	wmb();
+	__raw_writel(0, base + VSS_GATE);	/* disable FSM */
+	wmb();
+	__raw_writel(3, base + VSS_CLKRST);	/* assert reset */
+	wmb();
+	__raw_writel(1, base + VSS_CLKRST);	/* disable clock */
+	wmb();
+	__raw_writel(0, base + VSS_FTR);	/* disable all footers */
+	wmb();
+}
+
+void au1300_vss_block_control(int block, int enable)
+{
+	unsigned long flags;
+
+	if (alchemy_get_cputype() != ALCHEMY_CPU_AU1300)
+		return;
+
+	/* only one block at a time */
+	spin_lock_irqsave(&au1300_vss_lock, flags);
+	if (enable)
+		__enable_block(block);
+	else
+		__disable_block(block);
+	spin_unlock_irqrestore(&au1300_vss_lock, flags);
+}
+EXPORT_SYMBOL_GPL(au1300_vss_block_control);

arch/mips/alchemy/devboards/Makefile

@@ -4,15 +4,10 @@
 
 obj-y += prom.o bcsr.o platform.o
 obj-$(CONFIG_PM)		+= pm.o
-obj-$(CONFIG_MIPS_PB1000)	+= pb1000/
-obj-$(CONFIG_MIPS_PB1100)	+= pb1100/
-obj-$(CONFIG_MIPS_PB1200)	+= pb1200/
-obj-$(CONFIG_MIPS_PB1500)	+= pb1500/
-obj-$(CONFIG_MIPS_PB1550)	+= pb1550/
-obj-$(CONFIG_MIPS_DB1000)	+= db1x00/
-obj-$(CONFIG_MIPS_DB1100)	+= db1x00/
-obj-$(CONFIG_MIPS_DB1200)	+= db1200/
-obj-$(CONFIG_MIPS_DB1500)	+= db1x00/
-obj-$(CONFIG_MIPS_DB1550)	+= db1x00/
-obj-$(CONFIG_MIPS_BOSPORUS)	+= db1x00/
-obj-$(CONFIG_MIPS_MIRAGE)	+= db1x00/
+obj-$(CONFIG_MIPS_PB1100)	+= pb1100.o
+obj-$(CONFIG_MIPS_PB1500)	+= pb1500.o
+obj-$(CONFIG_MIPS_PB1550)	+= pb1550.o
+obj-$(CONFIG_MIPS_DB1000)	+= db1000.o
+obj-$(CONFIG_MIPS_DB1200)	+= db1200.o
+obj-$(CONFIG_MIPS_DB1300)	+= db1300.o
+obj-$(CONFIG_MIPS_DB1550)	+= db1550.o

arch/mips/alchemy/devboards/bcsr.c

@@ -97,14 +97,9 @@ static void bcsr_csc_handler(unsigned int irq, struct irq_desc *d)
 	enable_irq(irq);
 }
 
-/* NOTE: both the enable and mask bits must be cleared, otherwise the
- * CPLD generates tons of spurious interrupts (at least on my DB1200).
- *	-- mlau
- */
 static void bcsr_irq_mask(struct irq_data *d)
 {
 	unsigned short v = 1 << (d->irq - bcsr_csc_base);
-	__raw_writew(v, bcsr_virt + BCSR_REG_INTCLR);
 	__raw_writew(v, bcsr_virt + BCSR_REG_MASKCLR);
 	wmb();
 }
@@ -112,7 +107,6 @@ static void bcsr_irq_mask(struct irq_data *d)
 static void bcsr_irq_maskack(struct irq_data *d)
 {
 	unsigned short v = 1 << (d->irq - bcsr_csc_base);
-	__raw_writew(v, bcsr_virt + BCSR_REG_INTCLR);
 	__raw_writew(v, bcsr_virt + BCSR_REG_MASKCLR);
 	__raw_writew(v, bcsr_virt + BCSR_REG_INTSTAT);	/* ack */
 	wmb();
@@ -121,7 +115,6 @@ static void bcsr_irq_maskack(struct irq_data *d)
 static void bcsr_irq_unmask(struct irq_data *d)
 {
 	unsigned short v = 1 << (d->irq - bcsr_csc_base);
-	__raw_writew(v, bcsr_virt + BCSR_REG_INTSET);
 	__raw_writew(v, bcsr_virt + BCSR_REG_MASKSET);
 	wmb();
 }
@@ -137,9 +130,9 @@ void __init bcsr_init_irq(int csc_start, int csc_end, int hook_irq)
 {
 	unsigned int irq;
 
-	/* mask & disable & ack all */
-	__raw_writew(0xffff, bcsr_virt + BCSR_REG_INTCLR);
+	/* mask & enable & ack all */
 	__raw_writew(0xffff, bcsr_virt + BCSR_REG_MASKCLR);
+	__raw_writew(0xffff, bcsr_virt + BCSR_REG_INTSET);
 	__raw_writew(0xffff, bcsr_virt + BCSR_REG_INTSTAT);
 	wmb();
 

arch/mips/alchemy/devboards/db1200/Makefile

-obj-y += setup.o platform.o

arch/mips/alchemy/devboards/db1200/setup.c

-/*
- * Alchemy/AMD/RMI DB1200 board setup.
- *
- * Licensed under the terms outlined in the file COPYING in the root of
- * this source archive.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/io.h>
-#include <linux/kernel.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include <asm/mach-db1x00/db1200.h>
-
-const char *get_system_type(void)
-{
-	return "Alchemy Db1200";
-}
-
-void __init board_setup(void)
-{
-	unsigned long freq0, clksrc, div, pfc;
-	unsigned short whoami;
-
-	bcsr_init(DB1200_BCSR_PHYS_ADDR,
-		  DB1200_BCSR_PHYS_ADDR + DB1200_BCSR_HEXLED_OFS);
-
-	whoami = bcsr_read(BCSR_WHOAMI);
-	printk(KERN_INFO "Alchemy/AMD/RMI DB1200 Board, CPLD Rev %d"
-		"  Board-ID %d  Daughtercard ID %d\n",
-		(whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf);
-
-	/* SMBus/SPI on PSC0, Audio on PSC1 */
-	pfc = __raw_readl((void __iomem *)SYS_PINFUNC);
-	pfc &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
-	pfc &= ~(SYS_PINFUNC_P1A | SYS_PINFUNC_P1B | SYS_PINFUNC_FS3);
-	pfc |= SYS_PINFUNC_P1C;	/* SPI is configured later */
-	__raw_writel(pfc, (void __iomem *)SYS_PINFUNC);
-	wmb();
-
-	/* Clock configurations: PSC0: ~50MHz via Clkgen0, derived from
-	 * CPU clock; all other clock generators off/unused.
-	 */
-	div = (get_au1x00_speed() + 25000000) / 50000000;
-	if (div & 1)
-		div++;
-	div = ((div >> 1) - 1) & 0xff;
-
-	freq0 = div << SYS_FC_FRDIV0_BIT;
-	__raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0);
-	wmb();
-	freq0 |= SYS_FC_FE0;	/* enable F0 */
-	__raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0);
-	wmb();
-
-	/* psc0_intclk comes 1:1 from F0 */
-	clksrc = SYS_CS_MUX_FQ0 << SYS_CS_ME0_BIT;
-	__raw_writel(clksrc, (void __iomem *)SYS_CLKSRC);
-	wmb();
-}
-
-static int __init db1200_arch_init(void)
-{
-	/* GPIO7 is low-level triggered CPLD cascade */
-	irq_set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
-	bcsr_init_irq(DB1200_INT_BEGIN, DB1200_INT_END, AU1200_GPIO7_INT);
-
-	/* insert/eject pairs: one of both is always screaming.  To avoid
-	 * issues they must not be automatically enabled when initially
-	 * requested.
-	 */
-	irq_set_status_flags(DB1200_SD0_INSERT_INT, IRQ_NOAUTOEN);
-	irq_set_status_flags(DB1200_SD0_EJECT_INT, IRQ_NOAUTOEN);
-	irq_set_status_flags(DB1200_PC0_INSERT_INT, IRQ_NOAUTOEN);
-	irq_set_status_flags(DB1200_PC0_EJECT_INT, IRQ_NOAUTOEN);
-	irq_set_status_flags(DB1200_PC1_INSERT_INT, IRQ_NOAUTOEN);
-	irq_set_status_flags(DB1200_PC1_EJECT_INT, IRQ_NOAUTOEN);
-	return 0;
-}
-arch_initcall(db1200_arch_init);

arch/mips/alchemy/devboards/db1x00/Makefile

-#
-#  Copyright 2000, 2008 MontaVista Software Inc.
-#  Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor DBAu1xx0 boards.
-#
-
-obj-y := board_setup.o platform.o

arch/mips/alchemy/devboards/db1x00/board_setup.c

-/*
- *
- * BRIEF MODULE DESCRIPTION
- *	Alchemy Db1x00 board setup.
- *
- * Copyright 2000, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- *
- *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
- *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
- *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
- *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
- *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
- *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
- *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- *  You should have received a copy of the  GNU General Public License along
- *  with this program; if not, write  to the Free Software Foundation, Inc.,
- *  675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/pm.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-au1x00/au1xxx_eth.h>
-#include <asm/mach-db1x00/db1x00.h>
-#include <asm/mach-db1x00/bcsr.h>
-#include <asm/reboot.h>
-
-#include <prom.h>
-
-#ifdef CONFIG_MIPS_BOSPORUS
-char irq_tab_alchemy[][5] __initdata = {
-	[11] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff }, /* IDSEL 11 - miniPCI  */
-	[12] = { -1, AU1500_PCI_INTA, 0xff, 0xff, 0xff }, /* IDSEL 12 - SN1741   */
-	[13] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, AU1500_PCI_INTC, AU1500_PCI_INTD }, /* IDSEL 13 - PCI slot */
-};
-
-/*
- * Micrel/Kendin 5 port switch attached to MAC0,
- * MAC0 is associated with PHY address 5 (== WAN port)
- * MAC1 is not associated with any PHY, since it's connected directly
- * to the switch.
- * no interrupts are used
- */
-static struct au1000_eth_platform_data eth0_pdata = {
-	.phy_static_config	= 1,
-	.phy_addr		= 5,
-};
-
-static void bosporus_power_off(void)
-{
-	while (1)
-		asm volatile (".set mips3 ; wait ; .set mips0");
-}
-
-const char *get_system_type(void)
-{
-	return "Alchemy Bosporus Gateway Reference";
-}
-#endif
-
-
-#ifdef CONFIG_MIPS_MIRAGE
-static void mirage_power_off(void)
-{
-	alchemy_gpio_direction_output(210, 1);
-}
-
-const char *get_system_type(void)
-{
-	return "Alchemy Mirage";
-}
-#endif
-
-
-#if defined(CONFIG_MIPS_BOSPORUS) || defined(CONFIG_MIPS_MIRAGE)
-static void mips_softreset(void)
-{
-	asm volatile ("jr\t%0" : : "r"(0xbfc00000));
-}
-
-#else
-
-const char *get_system_type(void)
-{
-	return "Alchemy Db1x00";
-}
-#endif
-
-
-void __init board_setup(void)
-{
-	unsigned long bcsr1, bcsr2;
-
-	bcsr1 = DB1000_BCSR_PHYS_ADDR;
-	bcsr2 = DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS;
-
-#ifdef CONFIG_MIPS_DB1000
-	printk(KERN_INFO "AMD Alchemy Au1000/Db1000 Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1500
-	printk(KERN_INFO "AMD Alchemy Au1500/Db1500 Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1100
-	printk(KERN_INFO "AMD Alchemy Au1100/Db1100 Board\n");
-#endif
-#ifdef CONFIG_MIPS_BOSPORUS
-	au1xxx_override_eth_cfg(0, &eth0_pdata);
-
-	printk(KERN_INFO "AMD Alchemy Bosporus Board\n");
-#endif
-#ifdef CONFIG_MIPS_MIRAGE
-	printk(KERN_INFO "AMD Alchemy Mirage Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1550
-	printk(KERN_INFO "AMD Alchemy Au1550/Db1550 Board\n");
-
-	bcsr1 = DB1550_BCSR_PHYS_ADDR;
-	bcsr2 = DB1550_BCSR_PHYS_ADDR + DB1550_BCSR_HEXLED_OFS;
-#endif
-
-	/* initialize board register space */
-	bcsr_init(bcsr1, bcsr2);
-
-#if defined(CONFIG_IRDA) && defined(CONFIG_AU1000_FIR)
-	{
-		u32 pin_func;
-
-		/* Set IRFIRSEL instead of GPIO15 */
-		pin_func = au_readl(SYS_PINFUNC) | SYS_PF_IRF;
-		au_writel(pin_func, SYS_PINFUNC);
-		/* Power off until the driver is in use */
-		bcsr_mod(BCSR_RESETS, BCSR_RESETS_IRDA_MODE_MASK,
-			 BCSR_RESETS_IRDA_MODE_OFF);
-	}
-#endif
-	bcsr_write(BCSR_PCMCIA, 0);	/* turn off PCMCIA power */
-
-	/* Enable GPIO[31:0] inputs */
-	alchemy_gpio1_input_enable();
-
-#ifdef CONFIG_MIPS_MIRAGE
-	{
-		u32 pin_func;
-
-		/* GPIO[20] is output */
-		alchemy_gpio_direction_output(20, 0);
-
-		/* Set GPIO[210:208] instead of SSI_0 */
-		pin_func = au_readl(SYS_PINFUNC) | SYS_PF_S0;
-
-		/* Set GPIO[215:211] for LEDs */
-		pin_func |= 5 << 2;
-
-		/* Set GPIO[214:213] for more LEDs */
-		pin_func |= 5 << 12;
-
-		/* Set GPIO[207:200] instead of PCMCIA/LCD */
-		pin_func |= SYS_PF_LCD | SYS_PF_PC;
-		au_writel(pin_func, SYS_PINFUNC);
-
-		/*
-		 * Enable speaker amplifier.  This should
-		 * be part of the audio driver.
-		 */
-		alchemy_gpio_direction_output(209, 1);
-
-		pm_power_off = mirage_power_off;
-		_machine_halt = mirage_power_off;
-		_machine_restart = (void(*)(char *))mips_softreset;
-	}
-#endif
-
-#ifdef CONFIG_MIPS_BOSPORUS
-	pm_power_off = bosporus_power_off;
-	_machine_halt = bosporus_power_off;
-	_machine_restart = (void(*)(char *))mips_softreset;
-#endif
-	au_sync();
-}
-
-static int __init db1x00_init_irq(void)
-{
-#if defined(CONFIG_MIPS_MIRAGE)
-	irq_set_irq_type(AU1500_GPIO7_INT, IRQF_TRIGGER_RISING); /* TS pendown */
-#elif defined(CONFIG_MIPS_DB1550)
-	irq_set_irq_type(AU1550_GPIO0_INT, IRQF_TRIGGER_LOW);  /* CD0# */
-	irq_set_irq_type(AU1550_GPIO1_INT, IRQF_TRIGGER_LOW);  /* CD1# */
-	irq_set_irq_type(AU1550_GPIO3_INT, IRQF_TRIGGER_LOW);  /* CARD0# */
-	irq_set_irq_type(AU1550_GPIO5_INT, IRQF_TRIGGER_LOW);  /* CARD1# */
-	irq_set_irq_type(AU1550_GPIO21_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
-	irq_set_irq_type(AU1550_GPIO22_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
-#elif defined(CONFIG_MIPS_DB1500)
-	irq_set_irq_type(AU1500_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
-	irq_set_irq_type(AU1500_GPIO3_INT, IRQF_TRIGGER_LOW); /* CD1# */
-	irq_set_irq_type(AU1500_GPIO2_INT, IRQF_TRIGGER_LOW); /* CARD0# */
-	irq_set_irq_type(AU1500_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
-	irq_set_irq_type(AU1500_GPIO1_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
-	irq_set_irq_type(AU1500_GPIO4_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
-#elif defined(CONFIG_MIPS_DB1100)
-	irq_set_irq_type(AU1100_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
-	irq_set_irq_type(AU1100_GPIO3_INT, IRQF_TRIGGER_LOW); /* CD1# */
-	irq_set_irq_type(AU1100_GPIO2_INT, IRQF_TRIGGER_LOW); /* CARD0# */
-	irq_set_irq_type(AU1100_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
-	irq_set_irq_type(AU1100_GPIO1_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
-	irq_set_irq_type(AU1100_GPIO4_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
-#elif defined(CONFIG_MIPS_DB1000)
-	irq_set_irq_type(AU1000_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
-	irq_set_irq_type(AU1000_GPIO3_INT, IRQF_TRIGGER_LOW); /* CD1# */
-	irq_set_irq_type(AU1000_GPIO2_INT, IRQF_TRIGGER_LOW); /* CARD0# */
-	irq_set_irq_type(AU1000_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
-	irq_set_irq_type(AU1000_GPIO1_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
-	irq_set_irq_type(AU1000_GPIO4_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
-#endif
-	return 0;
-}
-arch_initcall(db1x00_init_irq);

arch/mips/alchemy/devboards/pb1000/Makefile

-#
-#  Copyright 2000, 2008 MontaVista Software Inc.
-#  Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor Pb1000 board.
-#
-
-obj-y := board_setup.o

arch/mips/alchemy/devboards/pb1100/board_setup.c → arch/mips/alchemy/devboards/pb1100.c

 /*
- * Copyright 2002, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
+ * Pb1100 board platform device registration
  *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
+ * Copyright (C) 2009 Manuel Lauss
  *
- *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
- *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
- *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
- *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
- *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
- *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
- *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
  *
- *  You should have received a copy of the  GNU General Public License along
- *  with this program; if not, write  to the Free Software Foundation, Inc.,
- *  675 Mass Ave, Cambridge, MA 02139, USA.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
  */
 
+#include <linux/delay.h>
 #include <linux/gpio.h>
 #include <linux/init.h>
-#include <linux/delay.h>
 #include <linux/interrupt.h>
-
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
 #include <asm/mach-au1x00/au1000.h>
 #include <asm/mach-db1x00/bcsr.h>
-
 #include <prom.h>
-
+#include "platform.h"
 
 const char *get_system_type(void)
 {
-	return "Alchemy Pb1100";
+	return "PB1100";
 }
 
 void __init board_setup(void)
@@ -115,13 +110,58 @@ void __init board_setup(void)
 	}
 }
 
-static int __init pb1100_init_irq(void)
+/******************************************************************************/
+
+static struct resource au1100_lcd_resources[] = {
+	[0] = {
+		.start	= AU1100_LCD_PHYS_ADDR,
+		.end	= AU1100_LCD_PHYS_ADDR + 0x800 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1100_LCD_INT,
+		.end	= AU1100_LCD_INT,
+		.flags	= IORESOURCE_IRQ,
+	}
+};
+
+static u64 au1100_lcd_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device au1100_lcd_device = {
+	.name		= "au1100-lcd",
+	.id		= 0,
+	.dev = {
+		.dma_mask		= &au1100_lcd_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+	.num_resources	= ARRAY_SIZE(au1100_lcd_resources),
+	.resource	= au1100_lcd_resources,
+};
+
+static int __init pb1100_dev_init(void)
 {
+	int swapped;
+
 	irq_set_irq_type(AU1100_GPIO9_INT, IRQF_TRIGGER_LOW); /* PCCD# */
 	irq_set_irq_type(AU1100_GPIO10_INT, IRQF_TRIGGER_LOW); /* PCSTSCHG# */
 	irq_set_irq_type(AU1100_GPIO11_INT, IRQF_TRIGGER_LOW); /* PCCard# */
 	irq_set_irq_type(AU1100_GPIO13_INT, IRQF_TRIGGER_LOW); /* DC_IRQ# */
 
+	/* PCMCIA. single socket, identical to Pb1500 */
+	db1x_register_pcmcia_socket(
+		AU1000_PCMCIA_ATTR_PHYS_ADDR,
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+		AU1000_PCMCIA_MEM_PHYS_ADDR,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,
+		AU1000_PCMCIA_IO_PHYS_ADDR,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,
+		AU1100_GPIO11_INT, AU1100_GPIO9_INT,	 /* card / insert */
+		/*AU1100_GPIO10_INT*/0, 0, 0); /* stschg / eject / id */
+
+	swapped = bcsr_read(BCSR_STATUS) &  BCSR_STATUS_DB1000_SWAPBOOT;
+	db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
+	platform_device_register(&au1100_lcd_device);
+
 	return 0;
 }
-arch_initcall(pb1100_init_irq);
+device_initcall(pb1100_dev_init);

arch/mips/alchemy/devboards/pb1100/Makefile

-#
-#  Copyright 2000, 2001, 2008 MontaVista Software Inc.
-#  Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor Pb1100 board.
-#
-
-obj-y := board_setup.o platform.o

arch/mips/alchemy/devboards/pb1200/Makefile

-#
-# Makefile for the Alchemy Semiconductor Pb1200/DBAu1200 boards.
-#
-
-obj-y := board_setup.o platform.o

arch/mips/alchemy/devboards/pb1500/Makefile

-#
-#  Copyright 2000, 2001, 2008 MontaVista Software Inc.
-#  Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor Pb1500 board.
-#
-
-obj-y := board_setup.o platform.o