Merge branch 'intel-cleanups'

Guangbin Huang says:

====================
net: intel: some cleanups

This patchset adds some cleanups for intel e1000/e1000e ethernet driver.
====================
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/intel/e1000/e1000_hw.c

@@ -2522,7 +2522,7 @@ s32 e1000_check_for_link(struct e1000_hw *hw)
 				 * turn it on. For compatibility with a TBI link
 				 * partner, we will store bad packets. Some
 				 * frames have an additional byte on the end and
-				 * will look like CRC errors to to the hardware.
+				 * will look like CRC errors to the hardware.
 				 */
 				if (!hw->tbi_compatibility_on) {
 					hw->tbi_compatibility_on = true;
@@ -2723,7 +2723,7 @@ static void e1000_shift_out_mdi_bits(struct e1000_hw *hw, u32 data, u16 count)
  * e1000_shift_in_mdi_bits - Shifts data bits in from the PHY
  * @hw: Struct containing variables accessed by shared code
  *
- * Bits are shifted in in MSB to LSB order.
+ * Bits are shifted in MSB to LSB order.
  */
 static u16 e1000_shift_in_mdi_bits(struct e1000_hw *hw)
 {

drivers/net/ethernet/intel/e1000/e1000_main.c

@@ -5245,7 +5245,7 @@ static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev,
 	if (!test_and_set_bit(__E1000_DISABLED, &adapter->flags))
 		pci_disable_device(pdev);
 
-	/* Request a slot slot reset. */
+	/* Request a slot reset. */
 	return PCI_ERS_RESULT_NEED_RESET;
 }
 

drivers/net/ethernet/intel/e1000e/ich8lan.c

@@ -4639,7 +4639,7 @@ static s32 e1000_id_led_init_pchlan(struct e1000_hw *hw)
  *  @hw: pointer to the HW structure
  *
  *  ICH8 use the PCI Express bus, but does not contain a PCI Express Capability
- *  register, so the the bus width is hard coded.
+ *  register, so the bus width is hard coded.
  **/
 static s32 e1000_get_bus_info_ich8lan(struct e1000_hw *hw)
 {

drivers/net/ethernet/intel/e1000e/netdev.c

@@ -7118,7 +7118,7 @@ static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev,
 
 	pci_disable_device(pdev);
 
-	/* Request a slot slot reset. */
+	/* Request a slot reset. */
 	return PCI_ERS_RESULT_NEED_RESET;
 }
 

drivers/net/ethernet/intel/e1000e/phy.c

@@ -2978,7 +2978,7 @@ static u32 e1000_get_phy_addr_for_hv_page(u32 page)
  *  @data: pointer to the data to be read or written
  *  @read: determines if operation is read or write
  *
- *  Reads the PHY register at offset and stores the retreived information
+ *  Reads the PHY register at offset and stores the retrieved information
  *  in data.  Assumes semaphore already acquired.  Note that the procedure
  *  to access these regs uses the address port and data port to read/write.
  *  These accesses done with PHY address 2 and without using pages.