Merge branch 'Documentation-networking-eliminate-doubled-words'

Randy Dunlap says:

====================
Documentation: networking: eliminate doubled words

Drop all duplicated words in Documentation/networking/ files.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/networking/arcnet.rst

@@ -434,7 +434,7 @@ can set up your network then:
 	ifconfig arc0 insight
 	route add insight arc0
 	route add freedom arc0	/* I would use the subnet here (like I said
-					to to in "single protocol" above),
+					to in "single protocol" above),
 					but the rest of the subnet
 					unfortunately lies across the PPP
 					link on freedom, which confuses

Documentation/networking/ax25.rst

@@ -6,7 +6,7 @@ AX.25
 
 To use the amateur radio protocols within Linux you will need to get a
 suitable copy of the AX.25 Utilities. More detailed information about
-AX.25, NET/ROM and ROSE, associated programs and and utilities can be
+AX.25, NET/ROM and ROSE, associated programs and utilities can be
 found on http://www.linux-ax25.org.
 
 There is an active mailing list for discussing Linux amateur radio matters

Documentation/networking/can_ucan_protocol.rst

@@ -144,7 +144,7 @@ UCAN_COMMAND_SET_BITTIMING
 
 *Host2Dev; mandatory*
 
-Setup bittiming by sending the the structure
+Setup bittiming by sending the structure
 ``ucan_ctl_payload_t.cmd_set_bittiming`` (see ``struct bittiming`` for
 details)
 
@@ -232,7 +232,7 @@ UCAN_IN_TX_COMPLETE
   zero
 
 The CAN device has sent a message to the CAN bus. It answers with a
-list of of tuples <echo-ids, flags>.
+list of tuples <echo-ids, flags>.
 
 The echo-id identifies the frame from (echos the id from a previous
 UCAN_OUT_TX message). The flag indicates the result of the

Documentation/networking/dsa/dsa.rst

@@ -95,7 +95,7 @@ Ethernet switch.
 Networking stack hooks
 ----------------------
 
-When a master netdev is used with DSA, a small hook is placed in in the
+When a master netdev is used with DSA, a small hook is placed in the
 networking stack is in order to have the DSA subsystem process the Ethernet
 switch specific tagging protocol. DSA accomplishes this by registering a
 specific (and fake) Ethernet type (later becoming ``skb->protocol``) with the

Documentation/networking/ip-sysctl.rst

@@ -741,7 +741,7 @@ tcp_fastopen - INTEGER
 
 	Default: 0x1
 
-	Note that that additional client or server features are only
+	Note that additional client or server features are only
 	effective if the basic support (0x1 and 0x2) are enabled respectively.
 
 tcp_fastopen_blackhole_timeout_sec - INTEGER

Documentation/networking/ipvs-sysctl.rst

@@ -114,7 +114,7 @@ drop_entry - INTEGER
 	modes (when there is no enough available memory, the strategy
 	is enabled and the variable is automatically set to 2,
 	otherwise the strategy is disabled and the variable is set to
-	1), and 3 means that that the strategy is always enabled.
+	1), and 3 means that the strategy is always enabled.
 
 drop_packet - INTEGER
 	- 0  - disabled (default)

Documentation/networking/rxrpc.rst

@@ -186,7 +186,7 @@ About the AF_RXRPC driver:
      time [tunable] after the last connection using it discarded, in case a new
      connection is made that could use it.
 
- (#) A client-side connection is only shared between calls if they have have
+ (#) A client-side connection is only shared between calls if they have
      the same key struct describing their security (and assuming the calls
      would otherwise share the connection).  Non-secured calls would also be
      able to share connections with each other.