iio: adc: ti-ads7924: add Texas Instruments ADS7924 driver

The Texas Instruments ADS7924 is a 4 channels, 12-bit analog to
digital converter (ADC) with an I2C interface.

Datasheet: https://www.ti.com/lit/gpn/ads7924Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230115170623.3680647-2-hugo@hugovil.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

MAINTAINERS

@@ -20776,6 +20776,13 @@ M:	Robert Richter <rric@kernel.org>
 S:	Odd Fixes
 F:	drivers/gpio/gpio-thunderx.c
 
+TI ADS7924 ADC DRIVER
+M:	Hugo Villeneuve <hvilleneuve@dimonoff.com>
+L:	linux-iio@vger.kernel.org
+S:	Supported
+F:	Documentation/devicetree/bindings/iio/adc/ti,ads7924.yaml
+F:	drivers/iio/adc/ti-ads7924.c
+
 TI AM437X VPFE DRIVER
 M:	"Lad, Prabhakar" <prabhakar.csengg@gmail.com>
 L:	linux-media@vger.kernel.org

drivers/iio/adc/Kconfig

@@ -1208,6 +1208,17 @@ config TI_ADS1015
 	  This driver can also be built as a module. If so, the module will be
 	  called ti-ads1015.
 
+config TI_ADS7924
+	tristate "Texas Instruments ADS7924 ADC"
+	depends on I2C
+	select REGMAP_I2C
+	help
+	  If you say yes here you get support for Texas Instruments ADS7924
+	  4 channels, 12-bit I2C ADC chip.
+
+	  This driver can also be built as a module. If so, the module will be
+	  called ti-ads7924.
+
 config TI_ADS7950
 	tristate "Texas Instruments ADS7950 ADC driver"
 	depends on SPI && GPIOLIB

drivers/iio/adc/Makefile

@@ -107,6 +107,7 @@ obj-$(CONFIG_TI_ADC108S102) += ti-adc108s102.o
 obj-$(CONFIG_TI_ADC128S052) += ti-adc128s052.o
 obj-$(CONFIG_TI_ADC161S626) += ti-adc161s626.o
 obj-$(CONFIG_TI_ADS1015) += ti-ads1015.o
+obj-$(CONFIG_TI_ADS7924) += ti-ads7924.o
 obj-$(CONFIG_TI_ADS7950) += ti-ads7950.o
 obj-$(CONFIG_TI_ADS8344) += ti-ads8344.o
 obj-$(CONFIG_TI_ADS8688) += ti-ads8688.o

drivers/iio/adc/ti-ads7924.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * IIO driver for Texas Instruments ADS7924 ADC, 12-bit, 4-Channels, I2C
+ *
+ * Author: Hugo Villeneuve <hvilleneuve@dimonoff.com>
+ * Copyright 2022 DimOnOff
+ *
+ * based on iio/adc/ti-ads1015.c
+ * Copyright (c) 2016, Intel Corporation.
+ *
+ * Datasheet: https://www.ti.com/lit/gpn/ads7924
+ */
+
+#include <linux/bitfield.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+
+#include <linux/iio/iio.h>
+#include <linux/iio/types.h>
+
+#define ADS7924_CHANNELS	 4
+#define ADS7924_BITS		12
+#define ADS7924_DATA_SHIFT	 4
+
+/* Registers. */
+#define ADS7924_MODECNTRL_REG	0x00
+#define ADS7924_INTCNTRL_REG	0x01
+#define ADS7924_DATA0_U_REG	0x02
+#define ADS7924_DATA0_L_REG	0x03
+#define ADS7924_DATA1_U_REG	0x04
+#define ADS7924_DATA1_L_REG	0x05
+#define ADS7924_DATA2_U_REG	0x06
+#define ADS7924_DATA2_L_REG	0x07
+#define ADS7924_DATA3_U_REG	0x08
+#define ADS7924_DATA3_L_REG	0x09
+#define ADS7924_ULR0_REG	0x0A
+#define ADS7924_LLR0_REG	0x0B
+#define ADS7924_ULR1_REG	0x0C
+#define ADS7924_LLR1_REG	0x0D
+#define ADS7924_ULR2_REG	0x0E
+#define ADS7924_LLR2_REG	0x0F
+#define ADS7924_ULR3_REG	0x10
+#define ADS7924_LLR3_REG	0x11
+#define ADS7924_INTCONFIG_REG	0x12
+#define ADS7924_SLPCONFIG_REG	0x13
+#define ADS7924_ACQCONFIG_REG	0x14
+#define ADS7924_PWRCONFIG_REG	0x15
+#define ADS7924_RESET_REG	0x16
+
+/*
+ * Register address INC bit: when set to '1', the register address is
+ * automatically incremented after every register read which allows convenient
+ * reading of multiple registers. Set INC to '0' when reading a single register.
+ */
+#define ADS7924_AUTO_INCREMENT_BIT	BIT(7)
+
+#define ADS7924_MODECNTRL_MODE_MASK	GENMASK(7, 2)
+
+#define ADS7924_MODECNTRL_SEL_MASK	GENMASK(1, 0)
+
+#define ADS7924_CFG_INTPOL_BIT		1
+#define ADS7924_CFG_INTTRIG_BIT		0
+
+#define ADS7924_CFG_INTPOL_MASK		BIT(ADS7924_CFG_INTPOL_BIT)
+#define ADS7924_CFG_INTTRIG_MASK	BIT(ADS7924_CFG_INTTRIG_BIT)
+
+/* Interrupt pin polarity */
+#define ADS7924_CFG_INTPOL_LOW		0
+#define ADS7924_CFG_INTPOL_HIGH		1
+
+/* Interrupt pin signaling */
+#define ADS7924_CFG_INTTRIG_LEVEL	0
+#define ADS7924_CFG_INTTRIG_EDGE	1
+
+/* Mode control values */
+#define ADS7924_MODECNTRL_IDLE			0x00
+#define ADS7924_MODECNTRL_AWAKE			0x20
+#define ADS7924_MODECNTRL_MANUAL_SINGLE		0x30
+#define ADS7924_MODECNTRL_MANUAL_SCAN		0x32
+#define ADS7924_MODECNTRL_AUTO_SINGLE		0x31
+#define ADS7924_MODECNTRL_AUTO_SCAN		0x33
+#define ADS7924_MODECNTRL_AUTO_SINGLE_SLEEP	0x39
+#define ADS7924_MODECNTRL_AUTO_SCAN_SLEEP	0x3B
+#define ADS7924_MODECNTRL_AUTO_BURST_SLEEP	0x3F
+
+#define ADS7924_ACQTIME_MASK	GENMASK(4, 0)
+
+#define ADS7924_PWRUPTIME_MASK	GENMASK(4, 0)
+
+/*
+ * The power-up time is allowed to elapse whenever the device has been shutdown
+ * in idle mode. Power-up time can allow external circuits, such as an
+ * operational amplifier, between the MUXOUT and ADCIN pins to turn on.
+ * The nominal time programmed by the PUTIME[4:0] register bits is given by:
+ *     t PU = PWRUPTIME[4:0] × 2 μs
+ * If a power-up time is not required, set the bits to '0' to effectively bypass.
+ */
+#define ADS7924_PWRUPTIME_US 0 /* Bypass (0us). */
+
+/*
+ * Acquisition Time according to ACQTIME[4:0] register bits.
+ * The Acquisition Time is given by:
+ *     t ACQ = (ACQTIME[4:0] × 2 μs) + 6 μs
+ * Using default value of 0 for ACQTIME[4:0] results in a minimum acquisition
+ * time of 6us.
+ */
+#define ADS7924_ACQTIME_US 6
+
+/* The conversion time is always 4μs and cannot be programmed by the user. */
+#define ADS7924_CONVTIME_US 4
+
+#define ADS7924_TOTAL_CONVTIME_US (ADS7924_PWRUPTIME_US + ADS7924_ACQTIME_US + \
+				   ADS7924_CONVTIME_US)
+
+#define ADS7924_V_CHAN(_chan, _addr) {				\
+	.type = IIO_VOLTAGE,					\
+	.indexed = 1,						\
+	.channel = _chan,					\
+	.address = _addr,					\
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW), 		\
+	.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),	\
+	.datasheet_name = "AIN"#_chan,				\
+}
+
+struct ads7924_data {
+	struct device *dev;
+	struct regmap *regmap;
+	struct regulator *vref_reg;
+
+	/* GPIO descriptor for device hard-reset pin. */
+	struct gpio_desc *reset_gpio;
+
+	/*
+	 * Protects ADC ops, e.g: concurrent sysfs/buffered
+	 * data reads, configuration updates
+	 */
+	struct mutex lock;
+
+	/*
+	 * Set to true when the ADC is switched to the continuous-conversion
+	 * mode and exits from a power-down state. This flag is used to avoid
+	 * getting the stale result from the conversion register.
+	 */
+	bool conv_invalid;
+};
+
+static bool ads7924_is_writeable_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case ADS7924_MODECNTRL_REG:
+	case ADS7924_INTCNTRL_REG:
+	case ADS7924_ULR0_REG:
+	case ADS7924_LLR0_REG:
+	case ADS7924_ULR1_REG:
+	case ADS7924_LLR1_REG:
+	case ADS7924_ULR2_REG:
+	case ADS7924_LLR2_REG:
+	case ADS7924_ULR3_REG:
+	case ADS7924_LLR3_REG:
+	case ADS7924_INTCONFIG_REG:
+	case ADS7924_SLPCONFIG_REG:
+	case ADS7924_ACQCONFIG_REG:
+	case ADS7924_PWRCONFIG_REG:
+	case ADS7924_RESET_REG:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static const struct regmap_config ads7924_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = ADS7924_RESET_REG,
+	.writeable_reg = ads7924_is_writeable_reg,
+};
+
+static const struct iio_chan_spec ads7924_channels[] = {
+	ADS7924_V_CHAN(0, ADS7924_DATA0_U_REG),
+	ADS7924_V_CHAN(1, ADS7924_DATA1_U_REG),
+	ADS7924_V_CHAN(2, ADS7924_DATA2_U_REG),
+	ADS7924_V_CHAN(3, ADS7924_DATA3_U_REG),
+};
+
+static int ads7924_get_adc_result(struct ads7924_data *data,
+				  struct iio_chan_spec const *chan, int *val)
+{
+	int ret;
+	__be16 be_val;
+
+	if (chan->channel < 0 || chan->channel >= ADS7924_CHANNELS)
+		return -EINVAL;
+
+	if (data->conv_invalid) {
+		int conv_time;
+
+		conv_time = ADS7924_TOTAL_CONVTIME_US;
+		/* Allow 10% for internal clock inaccuracy. */
+		conv_time += conv_time / 10;
+		usleep_range(conv_time, conv_time + 1);
+		data->conv_invalid = false;
+	}
+
+	ret = regmap_raw_read(data->regmap, ADS7924_AUTO_INCREMENT_BIT |
+			      chan->address, &be_val, sizeof(be_val));
+	if (ret)
+		return ret;
+
+	*val = be16_to_cpu(be_val) >> ADS7924_DATA_SHIFT;
+
+	return 0;
+}
+
+static int ads7924_read_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan, int *val,
+			    int *val2, long mask)
+{
+	int ret, vref_uv;
+	struct ads7924_data *data = iio_priv(indio_dev);
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		mutex_lock(&data->lock);
+		ret = ads7924_get_adc_result(data, chan, val);
+		mutex_unlock(&data->lock);
+		if (ret < 0)
+			return ret;
+
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_SCALE:
+		vref_uv = regulator_get_voltage(data->vref_reg);
+		if (vref_uv < 0)
+			return vref_uv;
+
+		*val =  vref_uv / 1000; /* Convert reg voltage to mV */
+		*val2 = ADS7924_BITS;
+		return IIO_VAL_FRACTIONAL_LOG2;
+	default:
+		return -EINVAL;
+	}
+}
+
+static const struct iio_info ads7924_info = {
+	.read_raw = ads7924_read_raw,
+};
+
+static int ads7924_get_channels_config(struct i2c_client *client,
+				       struct iio_dev *indio_dev)
+{
+	struct ads7924_data *priv = iio_priv(indio_dev);
+	struct device *dev = priv->dev;
+	struct fwnode_handle *node;
+	int num_channels = 0;
+
+	device_for_each_child_node(dev, node) {
+		u32 pval;
+		unsigned int channel;
+
+		if (fwnode_property_read_u32(node, "reg", &pval)) {
+			dev_err(dev, "invalid reg on %pfw\n", node);
+			continue;
+		}
+
+		channel = pval;
+		if (channel >= ADS7924_CHANNELS) {
+			dev_err(dev, "invalid channel index %d on %pfw\n",
+				channel, node);
+			continue;
+		}
+
+		num_channels++;
+	}
+
+	if (!num_channels)
+		return -EINVAL;
+
+	return 0;
+}
+
+static int ads7924_set_conv_mode(struct ads7924_data *data, int mode)
+{
+	int ret;
+	unsigned int mode_field;
+	struct device *dev = data->dev;
+
+	/*
+	 * When switching between modes, be sure to first select the Awake mode
+	 * and then switch to the desired mode. This procedure ensures the
+	 * internal control logic is properly synchronized.
+	 */
+	if (mode != ADS7924_MODECNTRL_IDLE) {
+		mode_field = FIELD_PREP(ADS7924_MODECNTRL_MODE_MASK,
+					ADS7924_MODECNTRL_AWAKE);
+
+		ret = regmap_update_bits(data->regmap, ADS7924_MODECNTRL_REG,
+					 ADS7924_MODECNTRL_MODE_MASK,
+					 mode_field);
+		if (ret) {
+			dev_err(dev, "failed to set awake mode (%pe)\n",
+				ERR_PTR(ret));
+			return ret;
+		}
+	}
+
+	mode_field = FIELD_PREP(ADS7924_MODECNTRL_MODE_MASK, mode);
+
+	ret = regmap_update_bits(data->regmap, ADS7924_MODECNTRL_REG,
+				 ADS7924_MODECNTRL_MODE_MASK, mode_field);
+	if (ret)
+		dev_err(dev, "failed to set mode %d (%pe)\n", mode,
+			ERR_PTR(ret));
+
+	return ret;
+}
+
+static int ads7924_reset(struct iio_dev *indio_dev)
+{
+	struct ads7924_data *data = iio_priv(indio_dev);
+
+	if (data->reset_gpio) {
+		gpiod_set_value(data->reset_gpio, 1); /* Assert. */
+		/* Educated guess: assert time not specified in datasheet... */
+		mdelay(100);
+		gpiod_set_value(data->reset_gpio, 0); /* Deassert. */
+		return 0;
+	}
+
+	/*
+	 * A write of 10101010 to this register will generate a
+	 * software reset of the ADS7924.
+	 */
+	return regmap_write(data->regmap, ADS7924_RESET_REG, 0b10101010);
+};
+
+static void ads7924_reg_disable(void *data)
+{
+	regulator_disable(data);
+}
+
+static void ads7924_set_idle_mode(void *data)
+{
+	ads7924_set_conv_mode(data, ADS7924_MODECNTRL_IDLE);
+}
+
+static int ads7924_probe(struct i2c_client *client)
+{
+	struct iio_dev *indio_dev;
+	struct ads7924_data *data;
+	struct device *dev = &client->dev;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
+	if (!indio_dev)
+		return dev_err_probe(dev, -ENOMEM,
+				     "failed to allocate iio device\n");
+
+	data = iio_priv(indio_dev);
+
+	data->dev = dev;
+
+	/* Initialize the reset GPIO as output with an initial value of 0. */
+	data->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(data->reset_gpio))
+		return dev_err_probe(dev, PTR_ERR(data->reset_gpio),
+				     "failed to get request reset GPIO\n");
+
+	mutex_init(&data->lock);
+
+	indio_dev->name = "ads7924";
+	indio_dev->modes = INDIO_DIRECT_MODE;
+
+	indio_dev->channels = ads7924_channels;
+	indio_dev->num_channels = ARRAY_SIZE(ads7924_channels);
+	indio_dev->info = &ads7924_info;
+
+	ret = ads7924_get_channels_config(client, indio_dev);
+	if (ret < 0)
+		return dev_err_probe(dev, ret,
+				     "failed to get channels configuration\n");
+
+	data->regmap = devm_regmap_init_i2c(client, &ads7924_regmap_config);
+	if (IS_ERR(data->regmap))
+		return dev_err_probe(dev, PTR_ERR(data->regmap),
+				     "failed to init regmap\n");
+
+	data->vref_reg = devm_regulator_get(dev, "vref");
+	if (IS_ERR(data->vref_reg))
+		return dev_err_probe(dev, PTR_ERR(data->vref_reg),
+				     "failed to get vref regulator\n");
+
+	ret = regulator_enable(data->vref_reg);
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "failed to enable regulator\n");
+
+	ret = devm_add_action_or_reset(dev, ads7924_reg_disable, data->vref_reg);
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "failed to add regulator disable action\n");
+
+	ret = ads7924_reset(indio_dev);
+	if (ret < 0)
+		return dev_err_probe(dev, ret,
+				     "failed to reset device\n");
+
+	ret = ads7924_set_conv_mode(data, ADS7924_MODECNTRL_AUTO_SCAN);
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "failed to set conversion mode\n");
+
+	ret = devm_add_action_or_reset(dev, ads7924_set_idle_mode, data);
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "failed to add idle mode action\n");
+
+	/* Use minimum signal acquire time. */
+	ret = regmap_update_bits(data->regmap, ADS7924_ACQCONFIG_REG,
+				 ADS7924_ACQTIME_MASK,
+				 FIELD_PREP(ADS7924_ACQTIME_MASK, 0));
+	if (ret < 0)
+		return dev_err_probe(dev, ret,
+				     "failed to configure signal acquire time\n");
+
+	/* Disable power-up time. */
+	ret = regmap_update_bits(data->regmap, ADS7924_PWRCONFIG_REG,
+				 ADS7924_PWRUPTIME_MASK,
+				 FIELD_PREP(ADS7924_PWRUPTIME_MASK, 0));
+	if (ret < 0)
+		return dev_err_probe(dev, ret,
+				     "failed to configure power-up time\n");
+
+	data->conv_invalid = true;
+
+	ret = devm_iio_device_register(dev, indio_dev);
+	if (ret < 0)
+		return dev_err_probe(dev, ret,
+				     "failed to register IIO device\n");
+
+	return 0;
+}
+
+static const struct i2c_device_id ads7924_id[] = {
+	{ "ads7924", 0 },
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, ads7924_id);
+
+static const struct of_device_id ads7924_of_match[] = {
+	{ .compatible = "ti,ads7924", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, ads7924_of_match);
+
+static struct i2c_driver ads7924_driver = {
+	.driver = {
+		.name = "ads7924",
+		.of_match_table = ads7924_of_match,
+	},
+	.probe_new	= ads7924_probe,
+	.id_table	= ads7924_id,
+};
+
+module_i2c_driver(ads7924_driver);
+
+MODULE_AUTHOR("Hugo Villeneuve <hvilleneuve@dimonoff.com>");
+MODULE_DESCRIPTION("Texas Instruments ADS7924 ADC I2C driver");
+MODULE_LICENSE("GPL");