Merge branch 'net-dsa-ksz-Add-Microchip-KSZ87xx-support'

Marek Vasut says:

====================
net: dsa: ksz: Add Microchip KSZ87xx support

This series adds support for Microchip KSZ87xx switches, which are
slightly simpler compared to KSZ9xxx .
====================
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/dsa/ksz.txt

@@ -5,6 +5,9 @@ Required properties:
 
 - compatible: For external switch chips, compatible string must be exactly one
   of the following:
+  - "microchip,ksz8765"
+  - "microchip,ksz8794"
+  - "microchip,ksz8795"
   - "microchip,ksz9477"
   - "microchip,ksz9897"
   - "microchip,ksz9896"

drivers/net/dsa/microchip/Kconfig

@@ -16,3 +16,20 @@ config NET_DSA_MICROCHIP_KSZ9477_SPI
 	select REGMAP_SPI
 	help
 	  Select to enable support for registering switches configured through SPI.
+
+menuconfig NET_DSA_MICROCHIP_KSZ8795
+	tristate "Microchip KSZ8795 series switch support"
+	depends on NET_DSA
+	select NET_DSA_MICROCHIP_KSZ_COMMON
+	help
+	  This driver adds support for Microchip KSZ8795 switch chips.
+
+config NET_DSA_MICROCHIP_KSZ8795_SPI
+	tristate "KSZ8795 series SPI connected switch driver"
+	depends on NET_DSA_MICROCHIP_KSZ8795 && SPI
+	select REGMAP_SPI
+	help
+	  This driver accesses KSZ8795 chip through SPI.
+
+	  It is required to use the KSZ8795 switch driver as the only access
+	  is through SPI.

drivers/net/dsa/microchip/Makefile

@@ -2,3 +2,5 @@
 obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ_COMMON)	+= ksz_common.o
 obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ9477)		+= ksz9477.o
 obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ9477_SPI)	+= ksz9477_spi.o
+obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ8795)		+= ksz8795.o
+obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ8795_SPI)	+= ksz8795_spi.o

drivers/net/dsa/microchip/ksz8795.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Microchip KSZ8795 switch driver
+ *
+ * Copyright (C) 2017 Microchip Technology Inc.
+ *	Tristram Ha <Tristram.Ha@microchip.com>
+ */
+
+#include <linux/delay.h>
+#include <linux/export.h>
+#include <linux/gpio.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_data/microchip-ksz.h>
+#include <linux/phy.h>
+#include <linux/etherdevice.h>
+#include <linux/if_bridge.h>
+#include <net/dsa.h>
+#include <net/switchdev.h>
+
+#include "ksz_priv.h"
+#include "ksz_common.h"
+#include "ksz8795_reg.h"
+
+static const struct {
+	char string[ETH_GSTRING_LEN];
+} mib_names[TOTAL_SWITCH_COUNTER_NUM] = {
+	{ "rx_hi" },
+	{ "rx_undersize" },
+	{ "rx_fragments" },
+	{ "rx_oversize" },
+	{ "rx_jabbers" },
+	{ "rx_symbol_err" },
+	{ "rx_crc_err" },
+	{ "rx_align_err" },
+	{ "rx_mac_ctrl" },
+	{ "rx_pause" },
+	{ "rx_bcast" },
+	{ "rx_mcast" },
+	{ "rx_ucast" },
+	{ "rx_64_or_less" },
+	{ "rx_65_127" },
+	{ "rx_128_255" },
+	{ "rx_256_511" },
+	{ "rx_512_1023" },
+	{ "rx_1024_1522" },
+	{ "rx_1523_2000" },
+	{ "rx_2001" },
+	{ "tx_hi" },
+	{ "tx_late_col" },
+	{ "tx_pause" },
+	{ "tx_bcast" },
+	{ "tx_mcast" },
+	{ "tx_ucast" },
+	{ "tx_deferred" },
+	{ "tx_total_col" },
+	{ "tx_exc_col" },
+	{ "tx_single_col" },
+	{ "tx_mult_col" },
+	{ "rx_total" },
+	{ "tx_total" },
+	{ "rx_discards" },
+	{ "tx_discards" },
+};
+
+static void ksz_cfg(struct ksz_device *dev, u32 addr, u8 bits, bool set)
+{
+	regmap_update_bits(dev->regmap[0], addr, bits, set ? bits : 0);
+}
+
+static void ksz_port_cfg(struct ksz_device *dev, int port, int offset, u8 bits,
+			 bool set)
+{
+	regmap_update_bits(dev->regmap[0], PORT_CTRL_ADDR(port, offset),
+			   bits, set ? bits : 0);
+}
+
+static int ksz8795_reset_switch(struct ksz_device *dev)
+{
+	/* reset switch */
+	ksz_write8(dev, REG_POWER_MANAGEMENT_1,
+		   SW_SOFTWARE_POWER_DOWN << SW_POWER_MANAGEMENT_MODE_S);
+	ksz_write8(dev, REG_POWER_MANAGEMENT_1, 0);
+
+	return 0;
+}
+
+static void ksz8795_set_prio_queue(struct ksz_device *dev, int port, int queue)
+{
+	u8 hi, lo;
+
+	/* Number of queues can only be 1, 2, or 4. */
+	switch (queue) {
+	case 4:
+	case 3:
+		queue = PORT_QUEUE_SPLIT_4;
+		break;
+	case 2:
+		queue = PORT_QUEUE_SPLIT_2;
+		break;
+	default:
+		queue = PORT_QUEUE_SPLIT_1;
+	}
+	ksz_pread8(dev, port, REG_PORT_CTRL_0, &lo);
+	ksz_pread8(dev, port, P_DROP_TAG_CTRL, &hi);
+	lo &= ~PORT_QUEUE_SPLIT_L;
+	if (queue & PORT_QUEUE_SPLIT_2)
+		lo |= PORT_QUEUE_SPLIT_L;
+	hi &= ~PORT_QUEUE_SPLIT_H;
+	if (queue & PORT_QUEUE_SPLIT_4)
+		hi |= PORT_QUEUE_SPLIT_H;
+	ksz_pwrite8(dev, port, REG_PORT_CTRL_0, lo);
+	ksz_pwrite8(dev, port, P_DROP_TAG_CTRL, hi);
+
+	/* Default is port based for egress rate limit. */
+	if (queue != PORT_QUEUE_SPLIT_1)
+		ksz_cfg(dev, REG_SW_CTRL_19, SW_OUT_RATE_LIMIT_QUEUE_BASED,
+			true);
+}
+
+static void ksz8795_r_mib_cnt(struct ksz_device *dev, int port, u16 addr,
+			      u64 *cnt)
+{
+	u16 ctrl_addr;
+	u32 data;
+	u8 check;
+	int loop;
+
+	ctrl_addr = addr + SWITCH_COUNTER_NUM * port;
+	ctrl_addr |= IND_ACC_TABLE(TABLE_MIB | TABLE_READ);
+
+	mutex_lock(&dev->alu_mutex);
+	ksz_write16(dev, REG_IND_CTRL_0, ctrl_addr);
+
+	/* It is almost guaranteed to always read the valid bit because of
+	 * slow SPI speed.
+	 */
+	for (loop = 2; loop > 0; loop--) {
+		ksz_read8(dev, REG_IND_MIB_CHECK, &check);
+
+		if (check & MIB_COUNTER_VALID) {
+			ksz_read32(dev, REG_IND_DATA_LO, &data);
+			if (check & MIB_COUNTER_OVERFLOW)
+				*cnt += MIB_COUNTER_VALUE + 1;
+			*cnt += data & MIB_COUNTER_VALUE;
+			break;
+		}
+	}
+	mutex_unlock(&dev->alu_mutex);
+}
+
+static void ksz8795_r_mib_pkt(struct ksz_device *dev, int port, u16 addr,
+			      u64 *dropped, u64 *cnt)
+{
+	u16 ctrl_addr;
+	u32 data;
+	u8 check;
+	int loop;
+
+	addr -= SWITCH_COUNTER_NUM;
+	ctrl_addr = (KS_MIB_TOTAL_RX_1 - KS_MIB_TOTAL_RX_0) * port;
+	ctrl_addr += addr + KS_MIB_TOTAL_RX_0;
+	ctrl_addr |= IND_ACC_TABLE(TABLE_MIB | TABLE_READ);
+
+	mutex_lock(&dev->alu_mutex);
+	ksz_write16(dev, REG_IND_CTRL_0, ctrl_addr);
+
+	/* It is almost guaranteed to always read the valid bit because of
+	 * slow SPI speed.
+	 */
+	for (loop = 2; loop > 0; loop--) {
+		ksz_read8(dev, REG_IND_MIB_CHECK, &check);
+
+		if (check & MIB_COUNTER_VALID) {
+			ksz_read32(dev, REG_IND_DATA_LO, &data);
+			if (addr < 2) {
+				u64 total;
+
+				total = check & MIB_TOTAL_BYTES_H;
+				total <<= 32;
+				*cnt += total;
+				*cnt += data;
+				if (check & MIB_COUNTER_OVERFLOW) {
+					total = MIB_TOTAL_BYTES_H + 1;
+					total <<= 32;
+					*cnt += total;
+				}
+			} else {
+				if (check & MIB_COUNTER_OVERFLOW)
+					*cnt += MIB_PACKET_DROPPED + 1;
+				*cnt += data & MIB_PACKET_DROPPED;
+			}
+			break;
+		}
+	}
+	mutex_unlock(&dev->alu_mutex);
+}
+
+static void ksz8795_freeze_mib(struct ksz_device *dev, int port, bool freeze)
+{
+	/* enable the port for flush/freeze function */
+	if (freeze)
+		ksz_cfg(dev, REG_SW_CTRL_6, BIT(port), true);
+	ksz_cfg(dev, REG_SW_CTRL_6, SW_MIB_COUNTER_FREEZE, freeze);
+
+	/* disable the port after freeze is done */
+	if (!freeze)
+		ksz_cfg(dev, REG_SW_CTRL_6, BIT(port), false);
+}
+
+static void ksz8795_port_init_cnt(struct ksz_device *dev, int port)
+{
+	struct ksz_port_mib *mib = &dev->ports[port].mib;
+
+	/* flush all enabled port MIB counters */
+	ksz_cfg(dev, REG_SW_CTRL_6, BIT(port), true);
+	ksz_cfg(dev, REG_SW_CTRL_6, SW_MIB_COUNTER_FLUSH, true);
+	ksz_cfg(dev, REG_SW_CTRL_6, BIT(port), false);
+
+	mib->cnt_ptr = 0;
+
+	/* Some ports may not have MIB counters before SWITCH_COUNTER_NUM. */
+	while (mib->cnt_ptr < dev->reg_mib_cnt) {
+		dev->dev_ops->r_mib_cnt(dev, port, mib->cnt_ptr,
+					&mib->counters[mib->cnt_ptr]);
+		++mib->cnt_ptr;
+	}
+
+	/* Some ports may not have MIB counters after SWITCH_COUNTER_NUM. */
+	while (mib->cnt_ptr < dev->mib_cnt) {
+		dev->dev_ops->r_mib_pkt(dev, port, mib->cnt_ptr,
+					NULL, &mib->counters[mib->cnt_ptr]);
+		++mib->cnt_ptr;
+	}
+	mib->cnt_ptr = 0;
+	memset(mib->counters, 0, dev->mib_cnt * sizeof(u64));
+}
+
+static void ksz8795_r_table(struct ksz_device *dev, int table, u16 addr,
+			    u64 *data)
+{
+	u16 ctrl_addr;
+
+	ctrl_addr = IND_ACC_TABLE(table | TABLE_READ) | addr;
+
+	mutex_lock(&dev->alu_mutex);
+	ksz_write16(dev, REG_IND_CTRL_0, ctrl_addr);
+	ksz_read64(dev, REG_IND_DATA_HI, data);
+	mutex_unlock(&dev->alu_mutex);
+}
+
+static void ksz8795_w_table(struct ksz_device *dev, int table, u16 addr,
+			    u64 data)
+{
+	u16 ctrl_addr;
+
+	ctrl_addr = IND_ACC_TABLE(table) | addr;
+
+	mutex_lock(&dev->alu_mutex);
+	ksz_write64(dev, REG_IND_DATA_HI, data);
+	ksz_write16(dev, REG_IND_CTRL_0, ctrl_addr);
+	mutex_unlock(&dev->alu_mutex);
+}
+
+static int ksz8795_valid_dyn_entry(struct ksz_device *dev, u8 *data)
+{
+	int timeout = 100;
+
+	do {
+		ksz_read8(dev, REG_IND_DATA_CHECK, data);
+		timeout--;
+	} while ((*data & DYNAMIC_MAC_TABLE_NOT_READY) && timeout);
+
+	/* Entry is not ready for accessing. */
+	if (*data & DYNAMIC_MAC_TABLE_NOT_READY) {
+		return -EAGAIN;
+	/* Entry is ready for accessing. */
+	} else {
+		ksz_read8(dev, REG_IND_DATA_8, data);
+
+		/* There is no valid entry in the table. */
+		if (*data & DYNAMIC_MAC_TABLE_MAC_EMPTY)
+			return -ENXIO;
+	}
+	return 0;
+}
+
+static int ksz8795_r_dyn_mac_table(struct ksz_device *dev, u16 addr,
+				   u8 *mac_addr, u8 *fid, u8 *src_port,
+				   u8 *timestamp, u16 *entries)
+{
+	u32 data_hi, data_lo;
+	u16 ctrl_addr;
+	u8 data;
+	int rc;
+
+	ctrl_addr = IND_ACC_TABLE(TABLE_DYNAMIC_MAC | TABLE_READ) | addr;
+
+	mutex_lock(&dev->alu_mutex);
+	ksz_write16(dev, REG_IND_CTRL_0, ctrl_addr);
+
+	rc = ksz8795_valid_dyn_entry(dev, &data);
+	if (rc == -EAGAIN) {
+		if (addr == 0)
+			*entries = 0;
+	} else if (rc == -ENXIO) {
+		*entries = 0;
+	/* At least one valid entry in the table. */
+	} else {
+		u64 buf = 0;
+		int cnt;
+
+		ksz_read64(dev, REG_IND_DATA_HI, &buf);
+		data_hi = (u32)(buf >> 32);
+		data_lo = (u32)buf;
+
+		/* Check out how many valid entry in the table. */
+		cnt = data & DYNAMIC_MAC_TABLE_ENTRIES_H;
+		cnt <<= DYNAMIC_MAC_ENTRIES_H_S;
+		cnt |= (data_hi & DYNAMIC_MAC_TABLE_ENTRIES) >>
+			DYNAMIC_MAC_ENTRIES_S;
+		*entries = cnt + 1;
+
+		*fid = (data_hi & DYNAMIC_MAC_TABLE_FID) >>
+			DYNAMIC_MAC_FID_S;
+		*src_port = (data_hi & DYNAMIC_MAC_TABLE_SRC_PORT) >>
+			DYNAMIC_MAC_SRC_PORT_S;
+		*timestamp = (data_hi & DYNAMIC_MAC_TABLE_TIMESTAMP) >>
+			DYNAMIC_MAC_TIMESTAMP_S;
+
+		mac_addr[5] = (u8)data_lo;
+		mac_addr[4] = (u8)(data_lo >> 8);
+		mac_addr[3] = (u8)(data_lo >> 16);
+		mac_addr[2] = (u8)(data_lo >> 24);
+
+		mac_addr[1] = (u8)data_hi;
+		mac_addr[0] = (u8)(data_hi >> 8);
+		rc = 0;
+	}
+	mutex_unlock(&dev->alu_mutex);
+
+	return rc;
+}
+
+static int ksz8795_r_sta_mac_table(struct ksz_device *dev, u16 addr,
+				   struct alu_struct *alu)
+{
+	u32 data_hi, data_lo;
+	u64 data;
+
+	ksz8795_r_table(dev, TABLE_STATIC_MAC, addr, &data);
+	data_hi = data >> 32;
+	data_lo = (u32)data;
+	if (data_hi & (STATIC_MAC_TABLE_VALID | STATIC_MAC_TABLE_OVERRIDE)) {
+		alu->mac[5] = (u8)data_lo;
+		alu->mac[4] = (u8)(data_lo >> 8);
+		alu->mac[3] = (u8)(data_lo >> 16);
+		alu->mac[2] = (u8)(data_lo >> 24);
+		alu->mac[1] = (u8)data_hi;
+		alu->mac[0] = (u8)(data_hi >> 8);
+		alu->port_forward = (data_hi & STATIC_MAC_TABLE_FWD_PORTS) >>
+			STATIC_MAC_FWD_PORTS_S;
+		alu->is_override =
+			(data_hi & STATIC_MAC_TABLE_OVERRIDE) ? 1 : 0;
+		data_hi >>= 1;
+		alu->is_use_fid = (data_hi & STATIC_MAC_TABLE_USE_FID) ? 1 : 0;
+		alu->fid = (data_hi & STATIC_MAC_TABLE_FID) >>
+			STATIC_MAC_FID_S;
+		return 0;
+	}
+	return -ENXIO;
+}
+
+static void ksz8795_w_sta_mac_table(struct ksz_device *dev, u16 addr,
+				    struct alu_struct *alu)
+{
+	u32 data_hi, data_lo;
+	u64 data;
+
+	data_lo = ((u32)alu->mac[2] << 24) |
+		((u32)alu->mac[3] << 16) |
+		((u32)alu->mac[4] << 8) | alu->mac[5];
+	data_hi = ((u32)alu->mac[0] << 8) | alu->mac[1];
+	data_hi |= (u32)alu->port_forward << STATIC_MAC_FWD_PORTS_S;
+
+	if (alu->is_override)
+		data_hi |= STATIC_MAC_TABLE_OVERRIDE;
+	if (alu->is_use_fid) {
+		data_hi |= STATIC_MAC_TABLE_USE_FID;
+		data_hi |= (u32)alu->fid << STATIC_MAC_FID_S;
+	}
+	if (alu->is_static)
+		data_hi |= STATIC_MAC_TABLE_VALID;
+	else
+		data_hi &= ~STATIC_MAC_TABLE_OVERRIDE;
+
+	data = (u64)data_hi << 32 | data_lo;
+	ksz8795_w_table(dev, TABLE_STATIC_MAC, addr, data);
+}
+
+static void ksz8795_from_vlan(u16 vlan, u8 *fid, u8 *member, u8 *valid)
+{
+	*fid = vlan & VLAN_TABLE_FID;
+	*member = (vlan & VLAN_TABLE_MEMBERSHIP) >> VLAN_TABLE_MEMBERSHIP_S;
+	*valid = !!(vlan & VLAN_TABLE_VALID);
+}
+
+static void ksz8795_to_vlan(u8 fid, u8 member, u8 valid, u16 *vlan)
+{
+	*vlan = fid;
+	*vlan |= (u16)member << VLAN_TABLE_MEMBERSHIP_S;
+	if (valid)
+		*vlan |= VLAN_TABLE_VALID;
+}
+
+static void ksz8795_r_vlan_entries(struct ksz_device *dev, u16 addr)
+{
+	u64 data;
+	int i;
+
+	ksz8795_r_table(dev, TABLE_VLAN, addr, &data);
+	addr *= 4;
+	for (i = 0; i < 4; i++) {
+		dev->vlan_cache[addr + i].table[0] = (u16)data;
+		data >>= VLAN_TABLE_S;
+	}
+}
+
+static void ksz8795_r_vlan_table(struct ksz_device *dev, u16 vid, u16 *vlan)
+{
+	int index;
+	u16 *data;
+	u16 addr;
+	u64 buf;
+
+	data = (u16 *)&buf;
+	addr = vid / 4;
+	index = vid & 3;
+	ksz8795_r_table(dev, TABLE_VLAN, addr, &buf);
+	*vlan = data[index];
+}
+
+static void ksz8795_w_vlan_table(struct ksz_device *dev, u16 vid, u16 vlan)
+{
+	int index;
+	u16 *data;
+	u16 addr;
+	u64 buf;
+
+	data = (u16 *)&buf;
+	addr = vid / 4;
+	index = vid & 3;
+	ksz8795_r_table(dev, TABLE_VLAN, addr, &buf);
+	data[index] = vlan;
+	dev->vlan_cache[vid].table[0] = vlan;
+	ksz8795_w_table(dev, TABLE_VLAN, addr, buf);
+}
+
+static void ksz8795_r_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 *val)
+{
+	u8 restart, speed, ctrl, link;
+	int processed = true;
+	u16 data = 0;
+	u8 p = phy;
+
+	switch (reg) {
+	case PHY_REG_CTRL:
+		ksz_pread8(dev, p, P_NEG_RESTART_CTRL, &restart);
+		ksz_pread8(dev, p, P_SPEED_STATUS, &speed);
+		ksz_pread8(dev, p, P_FORCE_CTRL, &ctrl);
+		if (restart & PORT_PHY_LOOPBACK)
+			data |= PHY_LOOPBACK;
+		if (ctrl & PORT_FORCE_100_MBIT)
+			data |= PHY_SPEED_100MBIT;
+		if (!(ctrl & PORT_AUTO_NEG_DISABLE))
+			data |= PHY_AUTO_NEG_ENABLE;
+		if (restart & PORT_POWER_DOWN)
+			data |= PHY_POWER_DOWN;
+		if (restart & PORT_AUTO_NEG_RESTART)
+			data |= PHY_AUTO_NEG_RESTART;
+		if (ctrl & PORT_FORCE_FULL_DUPLEX)
+			data |= PHY_FULL_DUPLEX;
+		if (speed & PORT_HP_MDIX)
+			data |= PHY_HP_MDIX;
+		if (restart & PORT_FORCE_MDIX)
+			data |= PHY_FORCE_MDIX;
+		if (restart & PORT_AUTO_MDIX_DISABLE)
+			data |= PHY_AUTO_MDIX_DISABLE;
+		if (restart & PORT_TX_DISABLE)
+			data |= PHY_TRANSMIT_DISABLE;
+		if (restart & PORT_LED_OFF)
+			data |= PHY_LED_DISABLE;
+		break;
+	case PHY_REG_STATUS:
+		ksz_pread8(dev, p, P_LINK_STATUS, &link);
+		data = PHY_100BTX_FD_CAPABLE |
+		       PHY_100BTX_CAPABLE |
+		       PHY_10BT_FD_CAPABLE |
+		       PHY_10BT_CAPABLE |
+		       PHY_AUTO_NEG_CAPABLE;
+		if (link & PORT_AUTO_NEG_COMPLETE)
+			data |= PHY_AUTO_NEG_ACKNOWLEDGE;
+		if (link & PORT_STAT_LINK_GOOD)
+			data |= PHY_LINK_STATUS;
+		break;
+	case PHY_REG_ID_1:
+		data = KSZ8795_ID_HI;
+		break;
+	case PHY_REG_ID_2:
+		data = KSZ8795_ID_LO;
+		break;
+	case PHY_REG_AUTO_NEGOTIATION:
+		ksz_pread8(dev, p, P_LOCAL_CTRL, &ctrl);
+		data = PHY_AUTO_NEG_802_3;
+		if (ctrl & PORT_AUTO_NEG_SYM_PAUSE)
+			data |= PHY_AUTO_NEG_SYM_PAUSE;
+		if (ctrl & PORT_AUTO_NEG_100BTX_FD)
+			data |= PHY_AUTO_NEG_100BTX_FD;
+		if (ctrl & PORT_AUTO_NEG_100BTX)
+			data |= PHY_AUTO_NEG_100BTX;
+		if (ctrl & PORT_AUTO_NEG_10BT_FD)
+			data |= PHY_AUTO_NEG_10BT_FD;
+		if (ctrl & PORT_AUTO_NEG_10BT)
+			data |= PHY_AUTO_NEG_10BT;
+		break;
+	case PHY_REG_REMOTE_CAPABILITY:
+		ksz_pread8(dev, p, P_REMOTE_STATUS, &link);
+		data = PHY_AUTO_NEG_802_3;
+		if (link & PORT_REMOTE_SYM_PAUSE)
+			data |= PHY_AUTO_NEG_SYM_PAUSE;
+		if (link & PORT_REMOTE_100BTX_FD)
+			data |= PHY_AUTO_NEG_100BTX_FD;
+		if (link & PORT_REMOTE_100BTX)
+			data |= PHY_AUTO_NEG_100BTX;
+		if (link & PORT_REMOTE_10BT_FD)
+			data |= PHY_AUTO_NEG_10BT_FD;
+		if (link & PORT_REMOTE_10BT)
+			data |= PHY_AUTO_NEG_10BT;
+		if (data & ~PHY_AUTO_NEG_802_3)
+			data |= PHY_REMOTE_ACKNOWLEDGE_NOT;
+		break;
+	default:
+		processed = false;
+		break;
+	}
+	if (processed)
+		*val = data;
+}
+
+static void ksz8795_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
+{
+	u8 p = phy;
+	u8 restart, speed, ctrl, data;
+
+	switch (reg) {
+	case PHY_REG_CTRL:
+
+		/* Do not support PHY reset function. */
+		if (val & PHY_RESET)
+			break;
+		ksz_pread8(dev, p, P_SPEED_STATUS, &speed);
+		data = speed;
+		if (val & PHY_HP_MDIX)
+			data |= PORT_HP_MDIX;
+		else
+			data &= ~PORT_HP_MDIX;
+		if (data != speed)
+			ksz_pwrite8(dev, p, P_SPEED_STATUS, data);
+		ksz_pread8(dev, p, P_FORCE_CTRL, &ctrl);
+		data = ctrl;
+		if (!(val & PHY_AUTO_NEG_ENABLE))
+			data |= PORT_AUTO_NEG_DISABLE;
+		else
+			data &= ~PORT_AUTO_NEG_DISABLE;
+
+		/* Fiber port does not support auto-negotiation. */
+		if (dev->ports[p].fiber)
+			data |= PORT_AUTO_NEG_DISABLE;
+		if (val & PHY_SPEED_100MBIT)
+			data |= PORT_FORCE_100_MBIT;
+		else
+			data &= ~PORT_FORCE_100_MBIT;
+		if (val & PHY_FULL_DUPLEX)
+			data |= PORT_FORCE_FULL_DUPLEX;
+		else
+			data &= ~PORT_FORCE_FULL_DUPLEX;
+		if (data != ctrl)
+			ksz_pwrite8(dev, p, P_FORCE_CTRL, data);
+		ksz_pread8(dev, p, P_NEG_RESTART_CTRL, &restart);
+		data = restart;
+		if (val & PHY_LED_DISABLE)
+			data |= PORT_LED_OFF;
+		else
+			data &= ~PORT_LED_OFF;
+		if (val & PHY_TRANSMIT_DISABLE)
+			data |= PORT_TX_DISABLE;
+		else
+			data &= ~PORT_TX_DISABLE;
+		if (val & PHY_AUTO_NEG_RESTART)
+			data |= PORT_AUTO_NEG_RESTART;
+		else
+			data &= ~(PORT_AUTO_NEG_RESTART);
+		if (val & PHY_POWER_DOWN)
+			data |= PORT_POWER_DOWN;
+		else
+			data &= ~PORT_POWER_DOWN;
+		if (val & PHY_AUTO_MDIX_DISABLE)
+			data |= PORT_AUTO_MDIX_DISABLE;
+		else
+			data &= ~PORT_AUTO_MDIX_DISABLE;
+		if (val & PHY_FORCE_MDIX)
+			data |= PORT_FORCE_MDIX;
+		else
+			data &= ~PORT_FORCE_MDIX;
+		if (val & PHY_LOOPBACK)
+			data |= PORT_PHY_LOOPBACK;
+		else
+			data &= ~PORT_PHY_LOOPBACK;
+		if (data != restart)
+			ksz_pwrite8(dev, p, P_NEG_RESTART_CTRL, data);
+		break;
+	case PHY_REG_AUTO_NEGOTIATION:
+		ksz_pread8(dev, p, P_LOCAL_CTRL, &ctrl);
+		data = ctrl;
+		data &= ~(PORT_AUTO_NEG_SYM_PAUSE |
+			  PORT_AUTO_NEG_100BTX_FD |
+			  PORT_AUTO_NEG_100BTX |
+			  PORT_AUTO_NEG_10BT_FD |
+			  PORT_AUTO_NEG_10BT);
+		if (val & PHY_AUTO_NEG_SYM_PAUSE)
+			data |= PORT_AUTO_NEG_SYM_PAUSE;
+		if (val & PHY_AUTO_NEG_100BTX_FD)
+			data |= PORT_AUTO_NEG_100BTX_FD;
+		if (val & PHY_AUTO_NEG_100BTX)
+			data |= PORT_AUTO_NEG_100BTX;
+		if (val & PHY_AUTO_NEG_10BT_FD)
+			data |= PORT_AUTO_NEG_10BT_FD;
+		if (val & PHY_AUTO_NEG_10BT)
+			data |= PORT_AUTO_NEG_10BT;
+		if (data != ctrl)
+			ksz_pwrite8(dev, p, P_LOCAL_CTRL, data);
+		break;
+	default:
+		break;
+	}
+}
+
+static enum dsa_tag_protocol ksz8795_get_tag_protocol(struct dsa_switch *ds,
+						      int port)
+{
+	return DSA_TAG_PROTO_KSZ8795;
+}
+
+static void ksz8795_get_strings(struct dsa_switch *ds, int port,
+				u32 stringset, uint8_t *buf)
+{
+	int i;
+
+	for (i = 0; i < TOTAL_SWITCH_COUNTER_NUM; i++) {
+		memcpy(buf + i * ETH_GSTRING_LEN, mib_names[i].string,
+		       ETH_GSTRING_LEN);
+	}
+}
+
+static void ksz8795_cfg_port_member(struct ksz_device *dev, int port,
+				    u8 member)
+{
+	u8 data;
+
+	ksz_pread8(dev, port, P_MIRROR_CTRL, &data);
+	data &= ~PORT_VLAN_MEMBERSHIP;
+	data |= (member & dev->port_mask);
+	ksz_pwrite8(dev, port, P_MIRROR_CTRL, data);
+	dev->ports[port].member = member;
+}
+
+static void ksz8795_port_stp_state_set(struct dsa_switch *ds, int port,
+				       u8 state)
+{
+	struct ksz_device *dev = ds->priv;
+	int forward = dev->member;
+	struct ksz_port *p;
+	int member = -1;
+	u8 data;
+
+	p = &dev->ports[port];
+
+	ksz_pread8(dev, port, P_STP_CTRL, &data);
+	data &= ~(PORT_TX_ENABLE | PORT_RX_ENABLE | PORT_LEARN_DISABLE);
+
+	switch (state) {
+	case BR_STATE_DISABLED:
+		data |= PORT_LEARN_DISABLE;
+		if (port < SWITCH_PORT_NUM)
+			member = 0;
+		break;
+	case BR_STATE_LISTENING:
+		data |= (PORT_RX_ENABLE | PORT_LEARN_DISABLE);
+		if (port < SWITCH_PORT_NUM &&
+		    p->stp_state == BR_STATE_DISABLED)
+			member = dev->host_mask | p->vid_member;
+		break;
+	case BR_STATE_LEARNING:
+		data |= PORT_RX_ENABLE;
+		break;
+	case BR_STATE_FORWARDING:
+		data |= (PORT_TX_ENABLE | PORT_RX_ENABLE);
+
+		/* This function is also used internally. */
+		if (port == dev->cpu_port)
+			break;
+
+		/* Port is a member of a bridge. */
+		if (dev->br_member & BIT(port)) {
+			dev->member |= BIT(port);
+			member = dev->member;
+		} else {
+			member = dev->host_mask | p->vid_member;
+		}
+		break;
+	case BR_STATE_BLOCKING:
+		data |= PORT_LEARN_DISABLE;
+		if (port < SWITCH_PORT_NUM &&
+		    p->stp_state == BR_STATE_DISABLED)
+			member = dev->host_mask | p->vid_member;
+		break;
+	default:
+		dev_err(ds->dev, "invalid STP state: %d\n", state);
+		return;
+	}
+
+	ksz_pwrite8(dev, port, P_STP_CTRL, data);
+	p->stp_state = state;
+	if (data & PORT_RX_ENABLE)
+		dev->rx_ports |= BIT(port);
+	else
+		dev->rx_ports &= ~BIT(port);
+	if (data & PORT_TX_ENABLE)
+		dev->tx_ports |= BIT(port);
+	else
+		dev->tx_ports &= ~BIT(port);
+
+	/* Port membership may share register with STP state. */
+	if (member >= 0 && member != p->member)
+		ksz8795_cfg_port_member(dev, port, (u8)member);
+
+	/* Check if forwarding needs to be updated. */
+	if (state != BR_STATE_FORWARDING) {
+		if (dev->br_member & BIT(port))
+			dev->member &= ~BIT(port);
+	}
+
+	/* When topology has changed the function ksz_update_port_member
+	 * should be called to modify port forwarding behavior.
+	 */
+	if (forward != dev->member)
+		ksz_update_port_member(dev, port);
+}
+
+static void ksz8795_flush_dyn_mac_table(struct ksz_device *dev, int port)
+{
+	u8 learn[TOTAL_PORT_NUM];
+	int first, index, cnt;
+	struct ksz_port *p;
+
+	if ((uint)port < TOTAL_PORT_NUM) {
+		first = port;
+		cnt = port + 1;
+	} else {
+		/* Flush all ports. */
+		first = 0;
+		cnt = dev->mib_port_cnt;
+	}
+	for (index = first; index < cnt; index++) {
+		p = &dev->ports[index];
+		if (!p->on)
+			continue;
+		ksz_pread8(dev, index, P_STP_CTRL, &learn[index]);
+		if (!(learn[index] & PORT_LEARN_DISABLE))
+			ksz_pwrite8(dev, index, P_STP_CTRL,
+				    learn[index] | PORT_LEARN_DISABLE);
+	}
+	ksz_cfg(dev, S_FLUSH_TABLE_CTRL, SW_FLUSH_DYN_MAC_TABLE, true);
+	for (index = first; index < cnt; index++) {
+		p = &dev->ports[index];
+		if (!p->on)
+			continue;
+		if (!(learn[index] & PORT_LEARN_DISABLE))
+			ksz_pwrite8(dev, index, P_STP_CTRL, learn[index]);
+	}
+}
+
+static int ksz8795_port_vlan_filtering(struct dsa_switch *ds, int port,
+				       bool flag)
+{
+	struct ksz_device *dev = ds->priv;
+
+	ksz_cfg(dev, S_MIRROR_CTRL, SW_VLAN_ENABLE, flag);
+
+	return 0;
+}
+
+static void ksz8795_port_vlan_add(struct dsa_switch *ds, int port,
+				  const struct switchdev_obj_port_vlan *vlan)
+{
+	bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED;
+	struct ksz_device *dev = ds->priv;
+	u16 data, vid, new_pvid = 0;
+	u8 fid, member, valid;
+
+	ksz_port_cfg(dev, port, P_TAG_CTRL, PORT_REMOVE_TAG, untagged);
+
+	for (vid = vlan->vid_begin; vid <= vlan->vid_end; vid++) {
+		ksz8795_r_vlan_table(dev, vid, &data);
+		ksz8795_from_vlan(data, &fid, &member, &valid);
+
+		/* First time to setup the VLAN entry. */
+		if (!valid) {
+			/* Need to find a way to map VID to FID. */
+			fid = 1;
+			valid = 1;
+		}
+		member |= BIT(port);
+
+		ksz8795_to_vlan(fid, member, valid, &data);
+		ksz8795_w_vlan_table(dev, vid, data);
+
+		/* change PVID */
+		if (vlan->flags & BRIDGE_VLAN_INFO_PVID)
+			new_pvid = vid;
+	}
+
+	if (new_pvid) {
+		ksz_pread16(dev, port, REG_PORT_CTRL_VID, &vid);
+		vid &= 0xfff;
+		vid |= new_pvid;
+		ksz_pwrite16(dev, port, REG_PORT_CTRL_VID, vid);
+	}
+}
+
+static int ksz8795_port_vlan_del(struct dsa_switch *ds, int port,
+				 const struct switchdev_obj_port_vlan *vlan)
+{
+	bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED;
+	struct ksz_device *dev = ds->priv;
+	u16 data, vid, pvid, new_pvid = 0;
+	u8 fid, member, valid;
+
+	ksz_pread16(dev, port, REG_PORT_CTRL_VID, &pvid);
+	pvid = pvid & 0xFFF;
+
+	ksz_port_cfg(dev, port, P_TAG_CTRL, PORT_REMOVE_TAG, untagged);
+
+	for (vid = vlan->vid_begin; vid <= vlan->vid_end; vid++) {
+		ksz8795_r_vlan_table(dev, vid, &data);
+		ksz8795_from_vlan(data, &fid, &member, &valid);
+
+		member &= ~BIT(port);
+
+		/* Invalidate the entry if no more member. */
+		if (!member) {
+			fid = 0;
+			valid = 0;
+		}
+
+		if (pvid == vid)
+			new_pvid = 1;
+
+		ksz8795_to_vlan(fid, member, valid, &data);
+		ksz8795_w_vlan_table(dev, vid, data);
+	}
+
+	if (new_pvid != pvid)
+		ksz_pwrite16(dev, port, REG_PORT_CTRL_VID, pvid);
+
+	return 0;
+}
+
+static int ksz8795_port_mirror_add(struct dsa_switch *ds, int port,
+				   struct dsa_mall_mirror_tc_entry *mirror,
+				   bool ingress)
+{
+	struct ksz_device *dev = ds->priv;
+
+	if (ingress) {
+		ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_RX, true);
+		dev->mirror_rx |= BIT(port);
+	} else {
+		ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_TX, true);
+		dev->mirror_tx |= BIT(port);
+	}
+
+	ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_SNIFFER, false);
+
+	/* configure mirror port */
+	if (dev->mirror_rx || dev->mirror_tx)
+		ksz_port_cfg(dev, mirror->to_local_port, P_MIRROR_CTRL,
+			     PORT_MIRROR_SNIFFER, true);
+
+	return 0;
+}
+
+static void ksz8795_port_mirror_del(struct dsa_switch *ds, int port,
+				    struct dsa_mall_mirror_tc_entry *mirror)
+{
+	struct ksz_device *dev = ds->priv;
+	u8 data;
+
+	if (mirror->ingress) {
+		ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_RX, false);
+		dev->mirror_rx &= ~BIT(port);
+	} else {
+		ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_TX, false);
+		dev->mirror_tx &= ~BIT(port);
+	}
+
+	ksz_pread8(dev, port, P_MIRROR_CTRL, &data);
+
+	if (!dev->mirror_rx && !dev->mirror_tx)
+		ksz_port_cfg(dev, mirror->to_local_port, P_MIRROR_CTRL,
+			     PORT_MIRROR_SNIFFER, false);
+}
+
+static void ksz8795_port_setup(struct ksz_device *dev, int port, bool cpu_port)
+{
+	struct ksz_port *p = &dev->ports[port];
+	u8 data8, member;
+
+	/* enable broadcast storm limit */
+	ksz_port_cfg(dev, port, P_BCAST_STORM_CTRL, PORT_BROADCAST_STORM, true);
+
+	ksz8795_set_prio_queue(dev, port, 4);
+
+	/* disable DiffServ priority */
+	ksz_port_cfg(dev, port, P_PRIO_CTRL, PORT_DIFFSERV_ENABLE, false);
+
+	/* replace priority */
+	ksz_port_cfg(dev, port, P_802_1P_CTRL, PORT_802_1P_REMAPPING, false);
+
+	/* enable 802.1p priority */
+	ksz_port_cfg(dev, port, P_PRIO_CTRL, PORT_802_1P_ENABLE, true);
+
+	if (cpu_port) {
+		/* Configure MII interface for proper network communication. */
+		ksz_read8(dev, REG_PORT_5_CTRL_6, &data8);
+		data8 &= ~PORT_INTERFACE_TYPE;
+		data8 &= ~PORT_GMII_1GPS_MODE;
+		switch (dev->interface) {
+		case PHY_INTERFACE_MODE_MII:
+			p->phydev.speed = SPEED_100;
+			break;
+		case PHY_INTERFACE_MODE_RMII:
+			data8 |= PORT_INTERFACE_RMII;
+			p->phydev.speed = SPEED_100;
+			break;
+		case PHY_INTERFACE_MODE_GMII:
+			data8 |= PORT_GMII_1GPS_MODE;
+			data8 |= PORT_INTERFACE_GMII;
+			p->phydev.speed = SPEED_1000;
+			break;
+		default:
+			data8 &= ~PORT_RGMII_ID_IN_ENABLE;
+			data8 &= ~PORT_RGMII_ID_OUT_ENABLE;
+			if (dev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+			    dev->interface == PHY_INTERFACE_MODE_RGMII_RXID)
+				data8 |= PORT_RGMII_ID_IN_ENABLE;
+			if (dev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+			    dev->interface == PHY_INTERFACE_MODE_RGMII_TXID)
+				data8 |= PORT_RGMII_ID_OUT_ENABLE;
+			data8 |= PORT_GMII_1GPS_MODE;
+			data8 |= PORT_INTERFACE_RGMII;
+			p->phydev.speed = SPEED_1000;
+			break;
+		}
+		ksz_write8(dev, REG_PORT_5_CTRL_6, data8);
+		p->phydev.duplex = 1;
+
+		member = dev->port_mask;
+		dev->on_ports = dev->host_mask;
+		dev->live_ports = dev->host_mask;
+	} else {
+		member = dev->host_mask | p->vid_member;
+		dev->on_ports |= BIT(port);
+
+		/* Link was detected before port is enabled. */
+		if (p->phydev.link)
+			dev->live_ports |= BIT(port);
+	}
+	ksz8795_cfg_port_member(dev, port, member);
+}
+
+static void ksz8795_config_cpu_port(struct dsa_switch *ds)
+{
+	struct ksz_device *dev = ds->priv;
+	struct ksz_port *p;
+	u8 remote;
+	int i;
+
+	ds->num_ports = dev->port_cnt + 1;
+
+	/* Switch marks the maximum frame with extra byte as oversize. */
+	ksz_cfg(dev, REG_SW_CTRL_2, SW_LEGAL_PACKET_DISABLE, true);
+	ksz_cfg(dev, S_TAIL_TAG_CTRL, SW_TAIL_TAG_ENABLE, true);
+
+	p = &dev->ports[dev->cpu_port];
+	p->vid_member = dev->port_mask;
+	p->on = 1;
+
+	ksz8795_port_setup(dev, dev->cpu_port, true);
+	dev->member = dev->host_mask;
+
+	for (i = 0; i < SWITCH_PORT_NUM; i++) {
+		p = &dev->ports[i];
+
+		/* Initialize to non-zero so that ksz_cfg_port_member() will
+		 * be called.
+		 */
+		p->vid_member = BIT(i);
+		p->member = dev->port_mask;
+		ksz8795_port_stp_state_set(ds, i, BR_STATE_DISABLED);
+
+		/* Last port may be disabled. */
+		if (i == dev->port_cnt)
+			break;
+		p->on = 1;
+		p->phy = 1;
+	}
+	for (i = 0; i < dev->phy_port_cnt; i++) {
+		p = &dev->ports[i];
+		if (!p->on)
+			continue;
+		ksz_pread8(dev, i, P_REMOTE_STATUS, &remote);
+		if (remote & PORT_FIBER_MODE)
+			p->fiber = 1;
+		if (p->fiber)
+			ksz_port_cfg(dev, i, P_STP_CTRL, PORT_FORCE_FLOW_CTRL,
+				     true);
+		else
+			ksz_port_cfg(dev, i, P_STP_CTRL, PORT_FORCE_FLOW_CTRL,
+				     false);
+	}
+}
+
+static int ksz8795_setup(struct dsa_switch *ds)
+{
+	struct ksz_device *dev = ds->priv;
+	struct alu_struct alu;
+	int i, ret = 0;
+
+	dev->vlan_cache = devm_kcalloc(dev->dev, sizeof(struct vlan_table),
+				       dev->num_vlans, GFP_KERNEL);
+	if (!dev->vlan_cache)
+		return -ENOMEM;
+
+	ret = ksz8795_reset_switch(dev);
+	if (ret) {
+		dev_err(ds->dev, "failed to reset switch\n");
+		return ret;
+	}
+
+	ksz_cfg(dev, S_REPLACE_VID_CTRL, SW_FLOW_CTRL, true);
+
+	/* Enable automatic fast aging when link changed detected. */
+	ksz_cfg(dev, S_LINK_AGING_CTRL, SW_LINK_AUTO_AGING, true);
+
+	/* Enable aggressive back off algorithm in half duplex mode. */
+	regmap_update_bits(dev->regmap[0], REG_SW_CTRL_1,
+			   SW_AGGR_BACKOFF, SW_AGGR_BACKOFF);
+
+	/*
+	 * Make sure unicast VLAN boundary is set as default and
+	 * enable no excessive collision drop.
+	 */
+	regmap_update_bits(dev->regmap[0], REG_SW_CTRL_2,
+			   UNICAST_VLAN_BOUNDARY | NO_EXC_COLLISION_DROP,
+			   UNICAST_VLAN_BOUNDARY | NO_EXC_COLLISION_DROP);
+
+	ksz8795_config_cpu_port(ds);
+
+	ksz_cfg(dev, REG_SW_CTRL_2, MULTICAST_STORM_DISABLE, true);
+
+	ksz_cfg(dev, S_REPLACE_VID_CTRL, SW_REPLACE_VID, false);
+
+	ksz_cfg(dev, S_MIRROR_CTRL, SW_MIRROR_RX_TX, false);
+
+	/* set broadcast storm protection 10% rate */
+	regmap_update_bits(dev->regmap[1], S_REPLACE_VID_CTRL,
+			   BROADCAST_STORM_RATE,
+			   (BROADCAST_STORM_VALUE *
+			   BROADCAST_STORM_PROT_RATE) / 100);
+
+	for (i = 0; i < VLAN_TABLE_ENTRIES; i++)
+		ksz8795_r_vlan_entries(dev, i);
+
+	/* Setup STP address for STP operation. */
+	memset(&alu, 0, sizeof(alu));
+	ether_addr_copy(alu.mac, eth_stp_addr);
+	alu.is_static = true;
+	alu.is_override = true;
+	alu.port_forward = dev->host_mask;
+
+	ksz8795_w_sta_mac_table(dev, 0, &alu);
+
+	ksz_init_mib_timer(dev);
+
+	return 0;
+}
+
+static const struct dsa_switch_ops ksz8795_switch_ops = {
+	.get_tag_protocol	= ksz8795_get_tag_protocol,
+	.setup			= ksz8795_setup,
+	.phy_read		= ksz_phy_read16,
+	.phy_write		= ksz_phy_write16,
+	.adjust_link		= ksz_adjust_link,
+	.port_enable		= ksz_enable_port,
+	.port_disable		= ksz_disable_port,
+	.get_strings		= ksz8795_get_strings,
+	.get_ethtool_stats	= ksz_get_ethtool_stats,
+	.get_sset_count		= ksz_sset_count,
+	.port_bridge_join	= ksz_port_bridge_join,
+	.port_bridge_leave	= ksz_port_bridge_leave,
+	.port_stp_state_set	= ksz8795_port_stp_state_set,
+	.port_fast_age		= ksz_port_fast_age,
+	.port_vlan_filtering	= ksz8795_port_vlan_filtering,
+	.port_vlan_prepare	= ksz_port_vlan_prepare,
+	.port_vlan_add		= ksz8795_port_vlan_add,
+	.port_vlan_del		= ksz8795_port_vlan_del,
+	.port_fdb_dump		= ksz_port_fdb_dump,
+	.port_mdb_prepare       = ksz_port_mdb_prepare,
+	.port_mdb_add           = ksz_port_mdb_add,
+	.port_mdb_del           = ksz_port_mdb_del,
+	.port_mirror_add	= ksz8795_port_mirror_add,
+	.port_mirror_del	= ksz8795_port_mirror_del,
+};
+
+static u32 ksz8795_get_port_addr(int port, int offset)
+{
+	return PORT_CTRL_ADDR(port, offset);
+}
+
+static int ksz8795_switch_detect(struct ksz_device *dev)
+{
+	u8 id1, id2;
+	u16 id16;
+	int ret;
+
+	/* read chip id */
+	ret = ksz_read16(dev, REG_CHIP_ID0, &id16);
+	if (ret)
+		return ret;
+
+	id1 = id16 >> 8;
+	id2 = id16 & SW_CHIP_ID_M;
+	if (id1 != FAMILY_ID ||
+	    (id2 != CHIP_ID_94 && id2 != CHIP_ID_95))
+		return -ENODEV;
+
+	dev->mib_port_cnt = TOTAL_PORT_NUM;
+	dev->phy_port_cnt = SWITCH_PORT_NUM;
+	dev->port_cnt = SWITCH_PORT_NUM;
+
+	if (id2 == CHIP_ID_95) {
+		u8 val;
+
+		id2 = 0x95;
+		ksz_read8(dev, REG_PORT_1_STATUS_0, &val);
+		if (val & PORT_FIBER_MODE)
+			id2 = 0x65;
+	} else if (id2 == CHIP_ID_94) {
+		dev->port_cnt--;
+		dev->last_port = dev->port_cnt;
+		id2 = 0x94;
+	}
+	id16 &= ~0xff;
+	id16 |= id2;
+	dev->chip_id = id16;
+
+	dev->cpu_port = dev->mib_port_cnt - 1;
+	dev->host_mask = BIT(dev->cpu_port);
+
+	return 0;
+}
+
+struct ksz_chip_data {
+	u16 chip_id;
+	const char *dev_name;
+	int num_vlans;
+	int num_alus;
+	int num_statics;
+	int cpu_ports;
+	int port_cnt;
+};
+
+static const struct ksz_chip_data ksz8795_switch_chips[] = {
+	{
+		.chip_id = 0x8795,
+		.dev_name = "KSZ8795",
+		.num_vlans = 4096,
+		.num_alus = 0,
+		.num_statics = 8,
+		.cpu_ports = 0x10,	/* can be configured as cpu port */
+		.port_cnt = 4,		/* total physical port count */
+	},
+	{
+		.chip_id = 0x8794,
+		.dev_name = "KSZ8794",
+		.num_vlans = 4096,
+		.num_alus = 0,
+		.num_statics = 8,
+		.cpu_ports = 0x10,	/* can be configured as cpu port */
+		.port_cnt = 3,		/* total physical port count */
+	},
+	{
+		.chip_id = 0x8765,
+		.dev_name = "KSZ8765",
+		.num_vlans = 4096,
+		.num_alus = 0,
+		.num_statics = 8,
+		.cpu_ports = 0x10,	/* can be configured as cpu port */
+		.port_cnt = 4,		/* total physical port count */
+	},
+};
+
+static int ksz8795_switch_init(struct ksz_device *dev)
+{
+	int i;
+
+	mutex_init(&dev->stats_mutex);
+	mutex_init(&dev->alu_mutex);
+	mutex_init(&dev->vlan_mutex);
+
+	dev->ds->ops = &ksz8795_switch_ops;
+
+	for (i = 0; i < ARRAY_SIZE(ksz8795_switch_chips); i++) {
+		const struct ksz_chip_data *chip = &ksz8795_switch_chips[i];
+
+		if (dev->chip_id == chip->chip_id) {
+			dev->name = chip->dev_name;
+			dev->num_vlans = chip->num_vlans;
+			dev->num_alus = chip->num_alus;
+			dev->num_statics = chip->num_statics;
+			dev->port_cnt = chip->port_cnt;
+			dev->cpu_ports = chip->cpu_ports;
+
+			break;
+		}
+	}
+
+	/* no switch found */
+	if (!dev->cpu_ports)
+		return -ENODEV;
+
+	dev->port_mask = BIT(dev->port_cnt) - 1;
+	dev->port_mask |= dev->host_mask;
+
+	dev->reg_mib_cnt = SWITCH_COUNTER_NUM;
+	dev->mib_cnt = TOTAL_SWITCH_COUNTER_NUM;
+
+	i = dev->mib_port_cnt;
+	dev->ports = devm_kzalloc(dev->dev, sizeof(struct ksz_port) * i,
+				  GFP_KERNEL);
+	if (!dev->ports)
+		return -ENOMEM;
+	for (i = 0; i < dev->mib_port_cnt; i++) {
+		mutex_init(&dev->ports[i].mib.cnt_mutex);
+		dev->ports[i].mib.counters =
+			devm_kzalloc(dev->dev,
+				     sizeof(u64) *
+				     (TOTAL_SWITCH_COUNTER_NUM + 1),
+				     GFP_KERNEL);
+		if (!dev->ports[i].mib.counters)
+			return -ENOMEM;
+	}
+
+	return 0;
+}
+
+static void ksz8795_switch_exit(struct ksz_device *dev)
+{
+	ksz8795_reset_switch(dev);
+}
+
+static const struct ksz_dev_ops ksz8795_dev_ops = {
+	.get_port_addr = ksz8795_get_port_addr,
+	.cfg_port_member = ksz8795_cfg_port_member,
+	.flush_dyn_mac_table = ksz8795_flush_dyn_mac_table,
+	.port_setup = ksz8795_port_setup,
+	.r_phy = ksz8795_r_phy,
+	.w_phy = ksz8795_w_phy,
+	.r_dyn_mac_table = ksz8795_r_dyn_mac_table,
+	.r_sta_mac_table = ksz8795_r_sta_mac_table,
+	.w_sta_mac_table = ksz8795_w_sta_mac_table,
+	.r_mib_cnt = ksz8795_r_mib_cnt,
+	.r_mib_pkt = ksz8795_r_mib_pkt,
+	.freeze_mib = ksz8795_freeze_mib,
+	.port_init_cnt = ksz8795_port_init_cnt,
+	.shutdown = ksz8795_reset_switch,
+	.detect = ksz8795_switch_detect,
+	.init = ksz8795_switch_init,
+	.exit = ksz8795_switch_exit,
+};
+
+int ksz8795_switch_register(struct ksz_device *dev)
+{
+	return ksz_switch_register(dev, &ksz8795_dev_ops);
+}
+EXPORT_SYMBOL(ksz8795_switch_register);
+
+MODULE_AUTHOR("Tristram Ha <Tristram.Ha@microchip.com>");
+MODULE_DESCRIPTION("Microchip KSZ8795 Series Switch DSA Driver");
+MODULE_LICENSE("GPL");

drivers/net/dsa/microchip/ksz8795_reg.h

+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Microchip KSZ8795 register definitions
+ *
+ * Copyright (c) 2017 Microchip Technology Inc.
+ *	Tristram Ha <Tristram.Ha@microchip.com>
+ */
+
+#ifndef __KSZ8795_REG_H
+#define __KSZ8795_REG_H
+
+#define KS_PORT_M			0x1F
+
+#define KS_PRIO_M			0x3
+#define KS_PRIO_S			2
+
+#define REG_CHIP_ID0			0x00
+
+#define FAMILY_ID			0x87
+
+#define REG_CHIP_ID1			0x01
+
+#define SW_CHIP_ID_M			0xF0
+#define SW_CHIP_ID_S			4
+#define SW_REVISION_M			0x0E
+#define SW_REVISION_S			1
+#define SW_START			0x01
+
+#define CHIP_ID_94			0x60
+#define CHIP_ID_95			0x90
+
+#define REG_SW_CTRL_0			0x02
+
+#define SW_NEW_BACKOFF			BIT(7)
+#define SW_GLOBAL_RESET			BIT(6)
+#define SW_FLUSH_DYN_MAC_TABLE		BIT(5)
+#define SW_FLUSH_STA_MAC_TABLE		BIT(4)
+#define SW_LINK_AUTO_AGING		BIT(0)
+
+#define REG_SW_CTRL_1			0x03
+
+#define SW_HUGE_PACKET			BIT(6)
+#define SW_TX_FLOW_CTRL_DISABLE		BIT(5)
+#define SW_RX_FLOW_CTRL_DISABLE		BIT(4)
+#define SW_CHECK_LENGTH			BIT(3)
+#define SW_AGING_ENABLE			BIT(2)
+#define SW_FAST_AGING			BIT(1)
+#define SW_AGGR_BACKOFF			BIT(0)
+
+#define REG_SW_CTRL_2			0x04
+
+#define UNICAST_VLAN_BOUNDARY		BIT(7)
+#define MULTICAST_STORM_DISABLE		BIT(6)
+#define SW_BACK_PRESSURE		BIT(5)
+#define FAIR_FLOW_CTRL			BIT(4)
+#define NO_EXC_COLLISION_DROP		BIT(3)
+#define SW_LEGAL_PACKET_DISABLE		BIT(1)
+
+#define REG_SW_CTRL_3			0x05
+ #define WEIGHTED_FAIR_QUEUE_ENABLE	BIT(3)
+
+#define SW_VLAN_ENABLE			BIT(7)
+#define SW_IGMP_SNOOP			BIT(6)
+#define SW_MIRROR_RX_TX			BIT(0)
+
+#define REG_SW_CTRL_4			0x06
+
+#define SW_HALF_DUPLEX_FLOW_CTRL	BIT(7)
+#define SW_HALF_DUPLEX			BIT(6)
+#define SW_FLOW_CTRL			BIT(5)
+#define SW_10_MBIT			BIT(4)
+#define SW_REPLACE_VID			BIT(3)
+#define BROADCAST_STORM_RATE_HI		0x07
+
+#define REG_SW_CTRL_5			0x07
+
+#define BROADCAST_STORM_RATE_LO		0xFF
+#define BROADCAST_STORM_RATE		0x07FF
+
+#define REG_SW_CTRL_6			0x08
+
+#define SW_MIB_COUNTER_FLUSH		BIT(7)
+#define SW_MIB_COUNTER_FREEZE		BIT(6)
+#define SW_MIB_COUNTER_CTRL_ENABLE	KS_PORT_M
+
+#define REG_SW_CTRL_9			0x0B
+
+#define SPI_CLK_125_MHZ			0x80
+#define SPI_CLK_62_5_MHZ		0x40
+#define SPI_CLK_31_25_MHZ		0x00
+
+#define SW_LED_MODE_M			0x3
+#define SW_LED_MODE_S			4
+#define SW_LED_LINK_ACT_SPEED		0
+#define SW_LED_LINK_ACT			1
+#define SW_LED_LINK_ACT_DUPLEX		2
+#define SW_LED_LINK_DUPLEX		3
+
+#define REG_SW_CTRL_10			0x0C
+
+#define SW_TAIL_TAG_ENABLE		BIT(1)
+#define SW_PASS_PAUSE			BIT(0)
+
+#define REG_SW_CTRL_11			0x0D
+
+#define REG_POWER_MANAGEMENT_1		0x0E
+
+#define SW_PLL_POWER_DOWN		BIT(5)
+#define SW_POWER_MANAGEMENT_MODE_M	0x3
+#define SW_POWER_MANAGEMENT_MODE_S	3
+#define SW_POWER_NORMAL			0
+#define SW_ENERGY_DETECTION		1
+#define SW_SOFTWARE_POWER_DOWN		2
+
+#define REG_POWER_MANAGEMENT_2		0x0F
+
+#define REG_PORT_1_CTRL_0		0x10
+#define REG_PORT_2_CTRL_0		0x20
+#define REG_PORT_3_CTRL_0		0x30
+#define REG_PORT_4_CTRL_0		0x40
+#define REG_PORT_5_CTRL_0		0x50
+
+#define PORT_BROADCAST_STORM		BIT(7)
+#define PORT_DIFFSERV_ENABLE		BIT(6)
+#define PORT_802_1P_ENABLE		BIT(5)
+#define PORT_BASED_PRIO_S		3
+#define PORT_BASED_PRIO_M		KS_PRIO_M
+#define PORT_BASED_PRIO_0		0
+#define PORT_BASED_PRIO_1		1
+#define PORT_BASED_PRIO_2		2
+#define PORT_BASED_PRIO_3		3
+#define PORT_INSERT_TAG			BIT(2)
+#define PORT_REMOVE_TAG			BIT(1)
+#define PORT_QUEUE_SPLIT_L		BIT(0)
+
+#define REG_PORT_1_CTRL_1		0x11
+#define REG_PORT_2_CTRL_1		0x21
+#define REG_PORT_3_CTRL_1		0x31
+#define REG_PORT_4_CTRL_1		0x41
+#define REG_PORT_5_CTRL_1		0x51
+
+#define PORT_MIRROR_SNIFFER		BIT(7)
+#define PORT_MIRROR_RX			BIT(6)
+#define PORT_MIRROR_TX			BIT(5)
+#define PORT_VLAN_MEMBERSHIP		KS_PORT_M
+
+#define REG_PORT_1_CTRL_2		0x12
+#define REG_PORT_2_CTRL_2		0x22
+#define REG_PORT_3_CTRL_2		0x32
+#define REG_PORT_4_CTRL_2		0x42
+#define REG_PORT_5_CTRL_2		0x52
+
+#define PORT_802_1P_REMAPPING		BIT(7)
+#define PORT_INGRESS_FILTER		BIT(6)
+#define PORT_DISCARD_NON_VID		BIT(5)
+#define PORT_FORCE_FLOW_CTRL		BIT(4)
+#define PORT_BACK_PRESSURE		BIT(3)
+#define PORT_TX_ENABLE			BIT(2)
+#define PORT_RX_ENABLE			BIT(1)
+#define PORT_LEARN_DISABLE		BIT(0)
+
+#define REG_PORT_1_CTRL_3		0x13
+#define REG_PORT_2_CTRL_3		0x23
+#define REG_PORT_3_CTRL_3		0x33
+#define REG_PORT_4_CTRL_3		0x43
+#define REG_PORT_5_CTRL_3		0x53
+#define REG_PORT_1_CTRL_4		0x14
+#define REG_PORT_2_CTRL_4		0x24
+#define REG_PORT_3_CTRL_4		0x34
+#define REG_PORT_4_CTRL_4		0x44
+#define REG_PORT_5_CTRL_4		0x54
+
+#define PORT_DEFAULT_VID		0x0001
+
+#define REG_PORT_1_CTRL_5		0x15
+#define REG_PORT_2_CTRL_5		0x25
+#define REG_PORT_3_CTRL_5		0x35
+#define REG_PORT_4_CTRL_5		0x45
+#define REG_PORT_5_CTRL_5		0x55
+
+#define PORT_ACL_ENABLE			BIT(2)
+#define PORT_AUTHEN_MODE		0x3
+#define PORT_AUTHEN_PASS		0
+#define PORT_AUTHEN_BLOCK		1
+#define PORT_AUTHEN_TRAP		2
+
+#define REG_PORT_5_CTRL_6		0x56
+
+#define PORT_MII_INTERNAL_CLOCK		BIT(7)
+#define PORT_GMII_1GPS_MODE		BIT(6)
+#define PORT_RGMII_ID_IN_ENABLE		BIT(4)
+#define PORT_RGMII_ID_OUT_ENABLE	BIT(3)
+#define PORT_GMII_MAC_MODE		BIT(2)
+#define PORT_INTERFACE_TYPE		0x3
+#define PORT_INTERFACE_MII		0
+#define PORT_INTERFACE_RMII		1
+#define PORT_INTERFACE_GMII		2
+#define PORT_INTERFACE_RGMII		3
+
+#define REG_PORT_1_CTRL_7		0x17
+#define REG_PORT_2_CTRL_7		0x27
+#define REG_PORT_3_CTRL_7		0x37
+#define REG_PORT_4_CTRL_7		0x47
+
+#define PORT_AUTO_NEG_ASYM_PAUSE	BIT(5)
+#define PORT_AUTO_NEG_SYM_PAUSE		BIT(4)
+#define PORT_AUTO_NEG_100BTX_FD		BIT(3)
+#define PORT_AUTO_NEG_100BTX		BIT(2)
+#define PORT_AUTO_NEG_10BT_FD		BIT(1)
+#define PORT_AUTO_NEG_10BT		BIT(0)
+
+#define REG_PORT_1_STATUS_0		0x18
+#define REG_PORT_2_STATUS_0		0x28
+#define REG_PORT_3_STATUS_0		0x38
+#define REG_PORT_4_STATUS_0		0x48
+
+/* For KSZ8765. */
+#define PORT_FIBER_MODE			BIT(7)
+
+#define PORT_REMOTE_ASYM_PAUSE		BIT(5)
+#define PORT_REMOTE_SYM_PAUSE		BIT(4)
+#define PORT_REMOTE_100BTX_FD		BIT(3)
+#define PORT_REMOTE_100BTX		BIT(2)
+#define PORT_REMOTE_10BT_FD		BIT(1)
+#define PORT_REMOTE_10BT		BIT(0)
+
+#define REG_PORT_1_STATUS_1		0x19
+#define REG_PORT_2_STATUS_1		0x29
+#define REG_PORT_3_STATUS_1		0x39
+#define REG_PORT_4_STATUS_1		0x49
+
+#define PORT_HP_MDIX			BIT(7)
+#define PORT_REVERSED_POLARITY		BIT(5)
+#define PORT_TX_FLOW_CTRL		BIT(4)
+#define PORT_RX_FLOW_CTRL		BIT(3)
+#define PORT_STAT_SPEED_100MBIT		BIT(2)
+#define PORT_STAT_FULL_DUPLEX		BIT(1)
+
+#define PORT_REMOTE_FAULT		BIT(0)
+
+#define REG_PORT_1_LINK_MD_CTRL		0x1A
+#define REG_PORT_2_LINK_MD_CTRL		0x2A
+#define REG_PORT_3_LINK_MD_CTRL		0x3A
+#define REG_PORT_4_LINK_MD_CTRL		0x4A
+
+#define PORT_CABLE_10M_SHORT		BIT(7)
+#define PORT_CABLE_DIAG_RESULT_M	0x3
+#define PORT_CABLE_DIAG_RESULT_S	5
+#define PORT_CABLE_STAT_NORMAL		0
+#define PORT_CABLE_STAT_OPEN		1
+#define PORT_CABLE_STAT_SHORT		2
+#define PORT_CABLE_STAT_FAILED		3
+#define PORT_START_CABLE_DIAG		BIT(4)
+#define PORT_FORCE_LINK			BIT(3)
+#define PORT_POWER_SAVING		BIT(2)
+#define PORT_PHY_REMOTE_LOOPBACK	BIT(1)
+#define PORT_CABLE_FAULT_COUNTER_H	0x01
+
+#define REG_PORT_1_LINK_MD_RESULT	0x1B
+#define REG_PORT_2_LINK_MD_RESULT	0x2B
+#define REG_PORT_3_LINK_MD_RESULT	0x3B
+#define REG_PORT_4_LINK_MD_RESULT	0x4B
+
+#define PORT_CABLE_FAULT_COUNTER_L	0xFF
+#define PORT_CABLE_FAULT_COUNTER	0x1FF
+
+#define REG_PORT_1_CTRL_9		0x1C
+#define REG_PORT_2_CTRL_9		0x2C
+#define REG_PORT_3_CTRL_9		0x3C
+#define REG_PORT_4_CTRL_9		0x4C
+
+#define PORT_AUTO_NEG_DISABLE		BIT(7)
+#define PORT_FORCE_100_MBIT		BIT(6)
+#define PORT_FORCE_FULL_DUPLEX		BIT(5)
+
+#define REG_PORT_1_CTRL_10		0x1D
+#define REG_PORT_2_CTRL_10		0x2D
+#define REG_PORT_3_CTRL_10		0x3D
+#define REG_PORT_4_CTRL_10		0x4D
+
+#define PORT_LED_OFF			BIT(7)
+#define PORT_TX_DISABLE			BIT(6)
+#define PORT_AUTO_NEG_RESTART		BIT(5)
+#define PORT_POWER_DOWN			BIT(3)
+#define PORT_AUTO_MDIX_DISABLE		BIT(2)
+#define PORT_FORCE_MDIX			BIT(1)
+#define PORT_MAC_LOOPBACK		BIT(0)
+
+#define REG_PORT_1_STATUS_2		0x1E
+#define REG_PORT_2_STATUS_2		0x2E
+#define REG_PORT_3_STATUS_2		0x3E
+#define REG_PORT_4_STATUS_2		0x4E
+
+#define PORT_MDIX_STATUS		BIT(7)
+#define PORT_AUTO_NEG_COMPLETE		BIT(6)
+#define PORT_STAT_LINK_GOOD		BIT(5)
+
+#define REG_PORT_1_STATUS_3		0x1F
+#define REG_PORT_2_STATUS_3		0x2F
+#define REG_PORT_3_STATUS_3		0x3F
+#define REG_PORT_4_STATUS_3		0x4F
+
+#define PORT_PHY_LOOPBACK		BIT(7)
+#define PORT_PHY_ISOLATE		BIT(5)
+#define PORT_PHY_SOFT_RESET		BIT(4)
+#define PORT_PHY_FORCE_LINK		BIT(3)
+#define PORT_PHY_MODE_M			0x7
+#define PHY_MODE_IN_AUTO_NEG		1
+#define PHY_MODE_10BT_HALF		2
+#define PHY_MODE_100BT_HALF		3
+#define PHY_MODE_10BT_FULL		5
+#define PHY_MODE_100BT_FULL		6
+#define PHY_MODE_ISOLDATE		7
+
+#define REG_PORT_CTRL_0			0x00
+#define REG_PORT_CTRL_1			0x01
+#define REG_PORT_CTRL_2			0x02
+#define REG_PORT_CTRL_VID		0x03
+
+#define REG_PORT_CTRL_5			0x05
+
+#define REG_PORT_CTRL_7			0x07
+#define REG_PORT_STATUS_0		0x08
+#define REG_PORT_STATUS_1		0x09
+#define REG_PORT_LINK_MD_CTRL		0x0A
+#define REG_PORT_LINK_MD_RESULT		0x0B
+#define REG_PORT_CTRL_9			0x0C
+#define REG_PORT_CTRL_10		0x0D
+#define REG_PORT_STATUS_2		0x0E
+#define REG_PORT_STATUS_3		0x0F
+
+#define REG_PORT_CTRL_12		0xA0
+#define REG_PORT_CTRL_13		0xA1
+#define REG_PORT_RATE_CTRL_3		0xA2
+#define REG_PORT_RATE_CTRL_2		0xA3
+#define REG_PORT_RATE_CTRL_1		0xA4
+#define REG_PORT_RATE_CTRL_0		0xA5
+#define REG_PORT_RATE_LIMIT		0xA6
+#define REG_PORT_IN_RATE_0		0xA7
+#define REG_PORT_IN_RATE_1		0xA8
+#define REG_PORT_IN_RATE_2		0xA9
+#define REG_PORT_IN_RATE_3		0xAA
+#define REG_PORT_OUT_RATE_0		0xAB
+#define REG_PORT_OUT_RATE_1		0xAC
+#define REG_PORT_OUT_RATE_2		0xAD
+#define REG_PORT_OUT_RATE_3		0xAE
+
+#define PORT_CTRL_ADDR(port, addr)		\
+	((addr) + REG_PORT_1_CTRL_0 + (port) *	\
+		(REG_PORT_2_CTRL_0 - REG_PORT_1_CTRL_0))
+
+#define REG_SW_MAC_ADDR_0		0x68
+#define REG_SW_MAC_ADDR_1		0x69
+#define REG_SW_MAC_ADDR_2		0x6A
+#define REG_SW_MAC_ADDR_3		0x6B
+#define REG_SW_MAC_ADDR_4		0x6C
+#define REG_SW_MAC_ADDR_5		0x6D
+
+#define REG_IND_CTRL_0			0x6E
+
+#define TABLE_EXT_SELECT_S		5
+#define TABLE_EEE_V			1
+#define TABLE_ACL_V			2
+#define TABLE_PME_V			4
+#define TABLE_LINK_MD_V			5
+#define TABLE_EEE			(TABLE_EEE_V << TABLE_EXT_SELECT_S)
+#define TABLE_ACL			(TABLE_ACL_V << TABLE_EXT_SELECT_S)
+#define TABLE_PME			(TABLE_PME_V << TABLE_EXT_SELECT_S)
+#define TABLE_LINK_MD			(TABLE_LINK_MD << TABLE_EXT_SELECT_S)
+#define TABLE_READ			BIT(4)
+#define TABLE_SELECT_S			2
+#define TABLE_STATIC_MAC_V		0
+#define TABLE_VLAN_V			1
+#define TABLE_DYNAMIC_MAC_V		2
+#define TABLE_MIB_V			3
+#define TABLE_STATIC_MAC		(TABLE_STATIC_MAC_V << TABLE_SELECT_S)
+#define TABLE_VLAN			(TABLE_VLAN_V << TABLE_SELECT_S)
+#define TABLE_DYNAMIC_MAC		(TABLE_DYNAMIC_MAC_V << TABLE_SELECT_S)
+#define TABLE_MIB			(TABLE_MIB_V << TABLE_SELECT_S)
+
+#define REG_IND_CTRL_1			0x6F
+
+#define TABLE_ENTRY_MASK		0x03FF
+#define TABLE_EXT_ENTRY_MASK		0x0FFF
+
+#define REG_IND_DATA_8			0x70
+#define REG_IND_DATA_7			0x71
+#define REG_IND_DATA_6			0x72
+#define REG_IND_DATA_5			0x73
+#define REG_IND_DATA_4			0x74
+#define REG_IND_DATA_3			0x75
+#define REG_IND_DATA_2			0x76
+#define REG_IND_DATA_1			0x77
+#define REG_IND_DATA_0			0x78
+
+#define REG_IND_DATA_PME_EEE_ACL	0xA0
+
+#define REG_IND_DATA_CHECK		REG_IND_DATA_6
+#define REG_IND_MIB_CHECK		REG_IND_DATA_4
+#define REG_IND_DATA_HI			REG_IND_DATA_7
+#define REG_IND_DATA_LO			REG_IND_DATA_3
+
+#define REG_INT_STATUS			0x7C
+#define REG_INT_ENABLE			0x7D
+
+#define INT_PME				BIT(4)
+
+#define REG_ACL_INT_STATUS		0x7E
+#define REG_ACL_INT_ENABLE		0x7F
+
+#define INT_PORT_5			BIT(4)
+#define INT_PORT_4			BIT(3)
+#define INT_PORT_3			BIT(2)
+#define INT_PORT_2			BIT(1)
+#define INT_PORT_1			BIT(0)
+
+#define INT_PORT_ALL			\
+	(INT_PORT_5 | INT_PORT_4 | INT_PORT_3 | INT_PORT_2 | INT_PORT_1)
+
+#define REG_SW_CTRL_12			0x80
+#define REG_SW_CTRL_13			0x81
+
+#define SWITCH_802_1P_MASK		3
+#define SWITCH_802_1P_BASE		3
+#define SWITCH_802_1P_SHIFT		2
+
+#define SW_802_1P_MAP_M			KS_PRIO_M
+#define SW_802_1P_MAP_S			KS_PRIO_S
+
+#define REG_SWITCH_CTRL_14		0x82
+
+#define SW_PRIO_MAPPING_M		KS_PRIO_M
+#define SW_PRIO_MAPPING_S		6
+#define SW_PRIO_MAP_3_HI		0
+#define SW_PRIO_MAP_2_HI		2
+#define SW_PRIO_MAP_0_LO		3
+
+#define REG_SW_CTRL_15			0x83
+#define REG_SW_CTRL_16			0x84
+#define REG_SW_CTRL_17			0x85
+#define REG_SW_CTRL_18			0x86
+
+#define SW_SELF_ADDR_FILTER_ENABLE	BIT(6)
+
+#define REG_SW_UNK_UCAST_CTRL		0x83
+#define REG_SW_UNK_MCAST_CTRL		0x84
+#define REG_SW_UNK_VID_CTRL		0x85
+#define REG_SW_UNK_IP_MCAST_CTRL	0x86
+
+#define SW_UNK_FWD_ENABLE		BIT(5)
+#define SW_UNK_FWD_MAP			KS_PORT_M
+
+#define REG_SW_CTRL_19			0x87
+
+#define SW_IN_RATE_LIMIT_PERIOD_M	0x3
+#define SW_IN_RATE_LIMIT_PERIOD_S	4
+#define SW_IN_RATE_LIMIT_16_MS		0
+#define SW_IN_RATE_LIMIT_64_MS		1
+#define SW_IN_RATE_LIMIT_256_MS		2
+#define SW_OUT_RATE_LIMIT_QUEUE_BASED	BIT(3)
+#define SW_INS_TAG_ENABLE		BIT(2)
+
+#define REG_TOS_PRIO_CTRL_0		0x90
+#define REG_TOS_PRIO_CTRL_1		0x91
+#define REG_TOS_PRIO_CTRL_2		0x92
+#define REG_TOS_PRIO_CTRL_3		0x93
+#define REG_TOS_PRIO_CTRL_4		0x94
+#define REG_TOS_PRIO_CTRL_5		0x95
+#define REG_TOS_PRIO_CTRL_6		0x96
+#define REG_TOS_PRIO_CTRL_7		0x97
+#define REG_TOS_PRIO_CTRL_8		0x98
+#define REG_TOS_PRIO_CTRL_9		0x99
+#define REG_TOS_PRIO_CTRL_10		0x9A
+#define REG_TOS_PRIO_CTRL_11		0x9B
+#define REG_TOS_PRIO_CTRL_12		0x9C
+#define REG_TOS_PRIO_CTRL_13		0x9D
+#define REG_TOS_PRIO_CTRL_14		0x9E
+#define REG_TOS_PRIO_CTRL_15		0x9F
+
+#define TOS_PRIO_M			KS_PRIO_M
+#define TOS_PRIO_S			KS_PRIO_S
+
+#define REG_SW_CTRL_20			0xA3
+
+#define SW_GMII_DRIVE_STRENGTH_S	4
+#define SW_DRIVE_STRENGTH_M		0x7
+#define SW_DRIVE_STRENGTH_2MA		0
+#define SW_DRIVE_STRENGTH_4MA		1
+#define SW_DRIVE_STRENGTH_8MA		2
+#define SW_DRIVE_STRENGTH_12MA		3
+#define SW_DRIVE_STRENGTH_16MA		4
+#define SW_DRIVE_STRENGTH_20MA		5
+#define SW_DRIVE_STRENGTH_24MA		6
+#define SW_DRIVE_STRENGTH_28MA		7
+#define SW_MII_DRIVE_STRENGTH_S		0
+
+#define REG_SW_CTRL_21			0xA4
+
+#define SW_IPV6_MLD_OPTION		BIT(3)
+#define SW_IPV6_MLD_SNOOP		BIT(2)
+
+#define REG_PORT_1_CTRL_12		0xB0
+#define REG_PORT_2_CTRL_12		0xC0
+#define REG_PORT_3_CTRL_12		0xD0
+#define REG_PORT_4_CTRL_12		0xE0
+#define REG_PORT_5_CTRL_12		0xF0
+
+#define PORT_PASS_ALL			BIT(6)
+#define PORT_INS_TAG_FOR_PORT_5_S	3
+#define PORT_INS_TAG_FOR_PORT_5		BIT(3)
+#define PORT_INS_TAG_FOR_PORT_4		BIT(2)
+#define PORT_INS_TAG_FOR_PORT_3		BIT(1)
+#define PORT_INS_TAG_FOR_PORT_2		BIT(0)
+
+#define REG_PORT_1_CTRL_13		0xB1
+#define REG_PORT_2_CTRL_13		0xC1
+#define REG_PORT_3_CTRL_13		0xD1
+#define REG_PORT_4_CTRL_13		0xE1
+#define REG_PORT_5_CTRL_13		0xF1
+
+#define PORT_QUEUE_SPLIT_H		BIT(1)
+#define PORT_QUEUE_SPLIT_1		0
+#define PORT_QUEUE_SPLIT_2		1
+#define PORT_QUEUE_SPLIT_4		2
+#define PORT_DROP_TAG			BIT(0)
+
+#define REG_PORT_1_CTRL_14		0xB2
+#define REG_PORT_2_CTRL_14		0xC2
+#define REG_PORT_3_CTRL_14		0xD2
+#define REG_PORT_4_CTRL_14		0xE2
+#define REG_PORT_5_CTRL_14		0xF2
+#define REG_PORT_1_CTRL_15		0xB3
+#define REG_PORT_2_CTRL_15		0xC3
+#define REG_PORT_3_CTRL_15		0xD3
+#define REG_PORT_4_CTRL_15		0xE3
+#define REG_PORT_5_CTRL_15		0xF3
+#define REG_PORT_1_CTRL_16		0xB4
+#define REG_PORT_2_CTRL_16		0xC4
+#define REG_PORT_3_CTRL_16		0xD4
+#define REG_PORT_4_CTRL_16		0xE4
+#define REG_PORT_5_CTRL_16		0xF4
+#define REG_PORT_1_CTRL_17		0xB5
+#define REG_PORT_2_CTRL_17		0xC5
+#define REG_PORT_3_CTRL_17		0xD5
+#define REG_PORT_4_CTRL_17		0xE5
+#define REG_PORT_5_CTRL_17		0xF5
+
+#define REG_PORT_1_RATE_CTRL_3		0xB2
+#define REG_PORT_1_RATE_CTRL_2		0xB3
+#define REG_PORT_1_RATE_CTRL_1		0xB4
+#define REG_PORT_1_RATE_CTRL_0		0xB5
+#define REG_PORT_2_RATE_CTRL_3		0xC2
+#define REG_PORT_2_RATE_CTRL_2		0xC3
+#define REG_PORT_2_RATE_CTRL_1		0xC4
+#define REG_PORT_2_RATE_CTRL_0		0xC5
+#define REG_PORT_3_RATE_CTRL_3		0xD2
+#define REG_PORT_3_RATE_CTRL_2		0xD3
+#define REG_PORT_3_RATE_CTRL_1		0xD4
+#define REG_PORT_3_RATE_CTRL_0		0xD5
+#define REG_PORT_4_RATE_CTRL_3		0xE2
+#define REG_PORT_4_RATE_CTRL_2		0xE3
+#define REG_PORT_4_RATE_CTRL_1		0xE4
+#define REG_PORT_4_RATE_CTRL_0		0xE5
+#define REG_PORT_5_RATE_CTRL_3		0xF2
+#define REG_PORT_5_RATE_CTRL_2		0xF3
+#define REG_PORT_5_RATE_CTRL_1		0xF4
+#define REG_PORT_5_RATE_CTRL_0		0xF5
+
+#define RATE_CTRL_ENABLE		BIT(7)
+#define RATE_RATIO_M			(BIT(7) - 1)
+
+#define PORT_OUT_RATE_ENABLE		BIT(7)
+
+#define REG_PORT_1_RATE_LIMIT		0xB6
+#define REG_PORT_2_RATE_LIMIT		0xC6
+#define REG_PORT_3_RATE_LIMIT		0xD6
+#define REG_PORT_4_RATE_LIMIT		0xE6
+#define REG_PORT_5_RATE_LIMIT		0xF6
+
+#define PORT_IN_PORT_BASED_S		6
+#define PORT_RATE_PACKET_BASED_S	5
+#define PORT_IN_FLOW_CTRL_S		4
+#define PORT_IN_LIMIT_MODE_M		0x3
+#define PORT_IN_LIMIT_MODE_S		2
+#define PORT_COUNT_IFG_S		1
+#define PORT_COUNT_PREAMBLE_S		0
+#define PORT_IN_PORT_BASED		BIT(PORT_IN_PORT_BASED_S)
+#define PORT_RATE_PACKET_BASED		BIT(PORT_RATE_PACKET_BASED_S)
+#define PORT_IN_FLOW_CTRL		BIT(PORT_IN_FLOW_CTRL_S)
+#define PORT_IN_ALL			0
+#define PORT_IN_UNICAST			1
+#define PORT_IN_MULTICAST		2
+#define PORT_IN_BROADCAST		3
+#define PORT_COUNT_IFG			BIT(PORT_COUNT_IFG_S)
+#define PORT_COUNT_PREAMBLE		BIT(PORT_COUNT_PREAMBLE_S)
+
+#define REG_PORT_1_IN_RATE_0		0xB7
+#define REG_PORT_2_IN_RATE_0		0xC7
+#define REG_PORT_3_IN_RATE_0		0xD7
+#define REG_PORT_4_IN_RATE_0		0xE7
+#define REG_PORT_5_IN_RATE_0		0xF7
+#define REG_PORT_1_IN_RATE_1		0xB8
+#define REG_PORT_2_IN_RATE_1		0xC8
+#define REG_PORT_3_IN_RATE_1		0xD8
+#define REG_PORT_4_IN_RATE_1		0xE8
+#define REG_PORT_5_IN_RATE_1		0xF8
+#define REG_PORT_1_IN_RATE_2		0xB9
+#define REG_PORT_2_IN_RATE_2		0xC9
+#define REG_PORT_3_IN_RATE_2		0xD9
+#define REG_PORT_4_IN_RATE_2		0xE9
+#define REG_PORT_5_IN_RATE_2		0xF9
+#define REG_PORT_1_IN_RATE_3		0xBA
+#define REG_PORT_2_IN_RATE_3		0xCA
+#define REG_PORT_3_IN_RATE_3		0xDA
+#define REG_PORT_4_IN_RATE_3		0xEA
+#define REG_PORT_5_IN_RATE_3		0xFA
+
+#define PORT_IN_RATE_ENABLE		BIT(7)
+#define PORT_RATE_LIMIT_M		(BIT(7) - 1)
+
+#define REG_PORT_1_OUT_RATE_0		0xBB
+#define REG_PORT_2_OUT_RATE_0		0xCB
+#define REG_PORT_3_OUT_RATE_0		0xDB
+#define REG_PORT_4_OUT_RATE_0		0xEB
+#define REG_PORT_5_OUT_RATE_0		0xFB
+#define REG_PORT_1_OUT_RATE_1		0xBC
+#define REG_PORT_2_OUT_RATE_1		0xCC
+#define REG_PORT_3_OUT_RATE_1		0xDC
+#define REG_PORT_4_OUT_RATE_1		0xEC
+#define REG_PORT_5_OUT_RATE_1		0xFC
+#define REG_PORT_1_OUT_RATE_2		0xBD
+#define REG_PORT_2_OUT_RATE_2		0xCD
+#define REG_PORT_3_OUT_RATE_2		0xDD
+#define REG_PORT_4_OUT_RATE_2		0xED
+#define REG_PORT_5_OUT_RATE_2		0xFD
+#define REG_PORT_1_OUT_RATE_3		0xBE
+#define REG_PORT_2_OUT_RATE_3		0xCE
+#define REG_PORT_3_OUT_RATE_3		0xDE
+#define REG_PORT_4_OUT_RATE_3		0xEE
+#define REG_PORT_5_OUT_RATE_3		0xFE
+
+/* PME */
+
+#define SW_PME_OUTPUT_ENABLE		BIT(1)
+#define SW_PME_ACTIVE_HIGH		BIT(0)
+
+#define PORT_MAGIC_PACKET_DETECT	BIT(2)
+#define PORT_LINK_UP_DETECT		BIT(1)
+#define PORT_ENERGY_DETECT		BIT(0)
+
+/* ACL */
+
+#define ACL_FIRST_RULE_M		0xF
+
+#define ACL_MODE_M			0x3
+#define ACL_MODE_S			4
+#define ACL_MODE_DISABLE		0
+#define ACL_MODE_LAYER_2		1
+#define ACL_MODE_LAYER_3		2
+#define ACL_MODE_LAYER_4		3
+#define ACL_ENABLE_M			0x3
+#define ACL_ENABLE_S			2
+#define ACL_ENABLE_2_COUNT		0
+#define ACL_ENABLE_2_TYPE		1
+#define ACL_ENABLE_2_MAC		2
+#define ACL_ENABLE_2_BOTH		3
+#define ACL_ENABLE_3_IP			1
+#define ACL_ENABLE_3_SRC_DST_COMP	2
+#define ACL_ENABLE_4_PROTOCOL		0
+#define ACL_ENABLE_4_TCP_PORT_COMP	1
+#define ACL_ENABLE_4_UDP_PORT_COMP	2
+#define ACL_ENABLE_4_TCP_SEQN_COMP	3
+#define ACL_SRC				BIT(1)
+#define ACL_EQUAL			BIT(0)
+
+#define ACL_MAX_PORT			0xFFFF
+
+#define ACL_MIN_PORT			0xFFFF
+#define ACL_IP_ADDR			0xFFFFFFFF
+#define ACL_TCP_SEQNUM			0xFFFFFFFF
+
+#define ACL_RESERVED			0xF8
+#define ACL_PORT_MODE_M			0x3
+#define ACL_PORT_MODE_S			1
+#define ACL_PORT_MODE_DISABLE		0
+#define ACL_PORT_MODE_EITHER		1
+#define ACL_PORT_MODE_IN_RANGE		2
+#define ACL_PORT_MODE_OUT_OF_RANGE	3
+
+#define ACL_TCP_FLAG_ENABLE		BIT(0)
+
+#define ACL_TCP_FLAG_M			0xFF
+
+#define ACL_TCP_FLAG			0xFF
+#define ACL_ETH_TYPE			0xFFFF
+#define ACL_IP_M			0xFFFFFFFF
+
+#define ACL_PRIO_MODE_M			0x3
+#define ACL_PRIO_MODE_S			6
+#define ACL_PRIO_MODE_DISABLE		0
+#define ACL_PRIO_MODE_HIGHER		1
+#define ACL_PRIO_MODE_LOWER		2
+#define ACL_PRIO_MODE_REPLACE		3
+#define ACL_PRIO_M			0x7
+#define ACL_PRIO_S			3
+#define ACL_VLAN_PRIO_REPLACE		BIT(2)
+#define ACL_VLAN_PRIO_M			0x7
+#define ACL_VLAN_PRIO_HI_M		0x3
+
+#define ACL_VLAN_PRIO_LO_M		0x8
+#define ACL_VLAN_PRIO_S			7
+#define ACL_MAP_MODE_M			0x3
+#define ACL_MAP_MODE_S			5
+#define ACL_MAP_MODE_DISABLE		0
+#define ACL_MAP_MODE_OR			1
+#define ACL_MAP_MODE_AND		2
+#define ACL_MAP_MODE_REPLACE		3
+#define ACL_MAP_PORT_M			0x1F
+
+#define ACL_CNT_M			(BIT(11) - 1)
+#define ACL_CNT_S			5
+#define ACL_MSEC_UNIT			BIT(4)
+#define ACL_INTR_MODE			BIT(3)
+
+#define REG_PORT_ACL_BYTE_EN_MSB	0x10
+
+#define ACL_BYTE_EN_MSB_M		0x3F
+
+#define REG_PORT_ACL_BYTE_EN_LSB	0x11
+
+#define ACL_ACTION_START		0xA
+#define ACL_ACTION_LEN			2
+#define ACL_INTR_CNT_START		0xB
+#define ACL_RULESET_START		0xC
+#define ACL_RULESET_LEN			2
+#define ACL_TABLE_LEN			14
+
+#define ACL_ACTION_ENABLE		0x000C
+#define ACL_MATCH_ENABLE		0x1FF0
+#define ACL_RULESET_ENABLE		0x2003
+#define ACL_BYTE_ENABLE			((ACL_BYTE_EN_MSB_M << 8) | 0xFF)
+#define ACL_MODE_ENABLE			(0x10 << 8)
+
+#define REG_PORT_ACL_CTRL_0		0x12
+
+#define PORT_ACL_WRITE_DONE		BIT(6)
+#define PORT_ACL_READ_DONE		BIT(5)
+#define PORT_ACL_WRITE			BIT(4)
+#define PORT_ACL_INDEX_M		0xF
+
+#define REG_PORT_ACL_CTRL_1		0x13
+
+#define PORT_ACL_FORCE_DLR_MISS		BIT(0)
+
+#ifndef PHY_REG_CTRL
+#define PHY_REG_CTRL			0
+
+#define PHY_RESET			BIT(15)
+#define PHY_LOOPBACK			BIT(14)
+#define PHY_SPEED_100MBIT		BIT(13)
+#define PHY_AUTO_NEG_ENABLE		BIT(12)
+#define PHY_POWER_DOWN			BIT(11)
+#define PHY_MII_DISABLE			BIT(10)
+#define PHY_AUTO_NEG_RESTART		BIT(9)
+#define PHY_FULL_DUPLEX			BIT(8)
+#define PHY_COLLISION_TEST_NOT		BIT(7)
+#define PHY_HP_MDIX			BIT(5)
+#define PHY_FORCE_MDIX			BIT(4)
+#define PHY_AUTO_MDIX_DISABLE		BIT(3)
+#define PHY_REMOTE_FAULT_DISABLE	BIT(2)
+#define PHY_TRANSMIT_DISABLE		BIT(1)
+#define PHY_LED_DISABLE			BIT(0)
+
+#define PHY_REG_STATUS			1
+
+#define PHY_100BT4_CAPABLE		BIT(15)
+#define PHY_100BTX_FD_CAPABLE		BIT(14)
+#define PHY_100BTX_CAPABLE		BIT(13)
+#define PHY_10BT_FD_CAPABLE		BIT(12)
+#define PHY_10BT_CAPABLE		BIT(11)
+#define PHY_MII_SUPPRESS_CAPABLE_NOT	BIT(6)
+#define PHY_AUTO_NEG_ACKNOWLEDGE	BIT(5)
+#define PHY_REMOTE_FAULT		BIT(4)
+#define PHY_AUTO_NEG_CAPABLE		BIT(3)
+#define PHY_LINK_STATUS			BIT(2)
+#define PHY_JABBER_DETECT_NOT		BIT(1)
+#define PHY_EXTENDED_CAPABILITY		BIT(0)
+
+#define PHY_REG_ID_1			2
+#define PHY_REG_ID_2			3
+
+#define PHY_REG_AUTO_NEGOTIATION	4
+
+#define PHY_AUTO_NEG_NEXT_PAGE_NOT	BIT(15)
+#define PHY_AUTO_NEG_REMOTE_FAULT_NOT	BIT(13)
+#define PHY_AUTO_NEG_SYM_PAUSE		BIT(10)
+#define PHY_AUTO_NEG_100BT4		BIT(9)
+#define PHY_AUTO_NEG_100BTX_FD		BIT(8)
+#define PHY_AUTO_NEG_100BTX		BIT(7)
+#define PHY_AUTO_NEG_10BT_FD		BIT(6)
+#define PHY_AUTO_NEG_10BT		BIT(5)
+#define PHY_AUTO_NEG_SELECTOR		0x001F
+#define PHY_AUTO_NEG_802_3		0x0001
+
+#define PHY_REG_REMOTE_CAPABILITY	5
+
+#define PHY_REMOTE_NEXT_PAGE_NOT	BIT(15)
+#define PHY_REMOTE_ACKNOWLEDGE_NOT	BIT(14)
+#define PHY_REMOTE_REMOTE_FAULT_NOT	BIT(13)
+#define PHY_REMOTE_SYM_PAUSE		BIT(10)
+#define PHY_REMOTE_100BTX_FD		BIT(8)
+#define PHY_REMOTE_100BTX		BIT(7)
+#define PHY_REMOTE_10BT_FD		BIT(6)
+#define PHY_REMOTE_10BT			BIT(5)
+#endif
+
+#define KSZ8795_ID_HI			0x0022
+#define KSZ8795_ID_LO			0x1550
+
+#define KSZ8795_SW_ID			0x8795
+
+#define PHY_REG_LINK_MD			0x1D
+
+#define PHY_START_CABLE_DIAG		BIT(15)
+#define PHY_CABLE_DIAG_RESULT		0x6000
+#define PHY_CABLE_STAT_NORMAL		0x0000
+#define PHY_CABLE_STAT_OPEN		0x2000
+#define PHY_CABLE_STAT_SHORT		0x4000
+#define PHY_CABLE_STAT_FAILED		0x6000
+#define PHY_CABLE_10M_SHORT		BIT(12)
+#define PHY_CABLE_FAULT_COUNTER		0x01FF
+
+#define PHY_REG_PHY_CTRL		0x1F
+
+#define PHY_MODE_M			0x7
+#define PHY_MODE_S			8
+#define PHY_STAT_REVERSED_POLARITY	BIT(5)
+#define PHY_STAT_MDIX			BIT(4)
+#define PHY_FORCE_LINK			BIT(3)
+#define PHY_POWER_SAVING_ENABLE		BIT(2)
+#define PHY_REMOTE_LOOPBACK		BIT(1)
+
+/* Chip resource */
+
+#define PRIO_QUEUES			4
+
+#define KS_PRIO_IN_REG			4
+
+#define TOTAL_PORT_NUM			5
+
+/* Host port can only be last of them. */
+#define SWITCH_PORT_NUM			(TOTAL_PORT_NUM - 1)
+
+#define KSZ8795_COUNTER_NUM		0x20
+#define TOTAL_KSZ8795_COUNTER_NUM	(KSZ8795_COUNTER_NUM + 4)
+
+#define SWITCH_COUNTER_NUM		KSZ8795_COUNTER_NUM
+#define TOTAL_SWITCH_COUNTER_NUM	TOTAL_KSZ8795_COUNTER_NUM
+
+/* Common names used by other drivers */
+
+#define P_BCAST_STORM_CTRL		REG_PORT_CTRL_0
+#define P_PRIO_CTRL			REG_PORT_CTRL_0
+#define P_TAG_CTRL			REG_PORT_CTRL_0
+#define P_MIRROR_CTRL			REG_PORT_CTRL_1
+#define P_802_1P_CTRL			REG_PORT_CTRL_2
+#define P_STP_CTRL			REG_PORT_CTRL_2
+#define P_LOCAL_CTRL			REG_PORT_CTRL_7
+#define P_REMOTE_STATUS			REG_PORT_STATUS_0
+#define P_FORCE_CTRL			REG_PORT_CTRL_9
+#define P_NEG_RESTART_CTRL		REG_PORT_CTRL_10
+#define P_SPEED_STATUS			REG_PORT_STATUS_1
+#define P_LINK_STATUS			REG_PORT_STATUS_2
+#define P_PASS_ALL_CTRL			REG_PORT_CTRL_12
+#define P_INS_SRC_PVID_CTRL		REG_PORT_CTRL_12
+#define P_DROP_TAG_CTRL			REG_PORT_CTRL_13
+#define P_RATE_LIMIT_CTRL		REG_PORT_RATE_LIMIT
+
+#define S_UNKNOWN_DA_CTRL		REG_SWITCH_CTRL_12
+#define S_FORWARD_INVALID_VID_CTRL	REG_FORWARD_INVALID_VID
+
+#define S_FLUSH_TABLE_CTRL		REG_SW_CTRL_0
+#define S_LINK_AGING_CTRL		REG_SW_CTRL_0
+#define S_HUGE_PACKET_CTRL		REG_SW_CTRL_1
+#define S_MIRROR_CTRL			REG_SW_CTRL_3
+#define S_REPLACE_VID_CTRL		REG_SW_CTRL_4
+#define S_PASS_PAUSE_CTRL		REG_SW_CTRL_10
+#define S_TAIL_TAG_CTRL			REG_SW_CTRL_10
+#define S_802_1P_PRIO_CTRL		REG_SW_CTRL_12
+#define S_TOS_PRIO_CTRL			REG_TOS_PRIO_CTRL_0
+#define S_IPV6_MLD_CTRL			REG_SW_CTRL_21
+
+#define IND_ACC_TABLE(table)		((table) << 8)
+
+/* Driver set switch broadcast storm protection at 10% rate. */
+#define BROADCAST_STORM_PROT_RATE	10
+
+/* 148,800 frames * 67 ms / 100 */
+#define BROADCAST_STORM_VALUE		9969
+
+/**
+ * STATIC_MAC_TABLE_ADDR		00-0000FFFF-FFFFFFFF
+ * STATIC_MAC_TABLE_FWD_PORTS		00-001F0000-00000000
+ * STATIC_MAC_TABLE_VALID		00-00200000-00000000
+ * STATIC_MAC_TABLE_OVERRIDE		00-00400000-00000000
+ * STATIC_MAC_TABLE_USE_FID		00-00800000-00000000
+ * STATIC_MAC_TABLE_FID			00-7F000000-00000000
+ */
+
+#define STATIC_MAC_TABLE_ADDR		0x0000FFFF
+#define STATIC_MAC_TABLE_FWD_PORTS	0x001F0000
+#define STATIC_MAC_TABLE_VALID		0x00200000
+#define STATIC_MAC_TABLE_OVERRIDE	0x00400000
+#define STATIC_MAC_TABLE_USE_FID	0x00800000
+#define STATIC_MAC_TABLE_FID		0x7F000000
+
+#define STATIC_MAC_FWD_PORTS_S		16
+#define STATIC_MAC_FID_S		24
+
+/**
+ * VLAN_TABLE_FID			00-007F007F-007F007F
+ * VLAN_TABLE_MEMBERSHIP		00-0F800F80-0F800F80
+ * VLAN_TABLE_VALID			00-10001000-10001000
+ */
+
+#define VLAN_TABLE_FID			0x007F
+#define VLAN_TABLE_MEMBERSHIP		0x0F80
+#define VLAN_TABLE_VALID		0x1000
+
+#define VLAN_TABLE_MEMBERSHIP_S		7
+#define VLAN_TABLE_S			16
+
+/**
+ * DYNAMIC_MAC_TABLE_ADDR		00-0000FFFF-FFFFFFFF
+ * DYNAMIC_MAC_TABLE_FID		00-007F0000-00000000
+ * DYNAMIC_MAC_TABLE_NOT_READY		00-00800000-00000000
+ * DYNAMIC_MAC_TABLE_SRC_PORT		00-07000000-00000000
+ * DYNAMIC_MAC_TABLE_TIMESTAMP		00-18000000-00000000
+ * DYNAMIC_MAC_TABLE_ENTRIES		7F-E0000000-00000000
+ * DYNAMIC_MAC_TABLE_MAC_EMPTY		80-00000000-00000000
+ */
+
+#define DYNAMIC_MAC_TABLE_ADDR		0x0000FFFF
+#define DYNAMIC_MAC_TABLE_FID		0x007F0000
+#define DYNAMIC_MAC_TABLE_SRC_PORT	0x07000000
+#define DYNAMIC_MAC_TABLE_TIMESTAMP	0x18000000
+#define DYNAMIC_MAC_TABLE_ENTRIES	0xE0000000
+
+#define DYNAMIC_MAC_TABLE_NOT_READY	0x80
+
+#define DYNAMIC_MAC_TABLE_ENTRIES_H	0x7F
+#define DYNAMIC_MAC_TABLE_MAC_EMPTY	0x80
+
+#define DYNAMIC_MAC_FID_S		16
+#define DYNAMIC_MAC_SRC_PORT_S		24
+#define DYNAMIC_MAC_TIMESTAMP_S		27
+#define DYNAMIC_MAC_ENTRIES_S		29
+#define DYNAMIC_MAC_ENTRIES_H_S		3
+
+/**
+ * MIB_COUNTER_VALUE			00-00000000-3FFFFFFF
+ * MIB_TOTAL_BYTES			00-0000000F-FFFFFFFF
+ * MIB_PACKET_DROPPED			00-00000000-0000FFFF
+ * MIB_COUNTER_VALID			00-00000020-00000000
+ * MIB_COUNTER_OVERFLOW			00-00000040-00000000
+ */
+
+#define MIB_COUNTER_OVERFLOW		BIT(6)
+#define MIB_COUNTER_VALID		BIT(5)
+
+#define MIB_COUNTER_VALUE		0x3FFFFFFF
+
+#define KS_MIB_TOTAL_RX_0		0x100
+#define KS_MIB_TOTAL_TX_0		0x101
+#define KS_MIB_PACKET_DROPPED_RX_0	0x102
+#define KS_MIB_PACKET_DROPPED_TX_0	0x103
+#define KS_MIB_TOTAL_RX_1		0x104
+#define KS_MIB_TOTAL_TX_1		0x105
+#define KS_MIB_PACKET_DROPPED_TX_1	0x106
+#define KS_MIB_PACKET_DROPPED_RX_1	0x107
+#define KS_MIB_TOTAL_RX_2		0x108
+#define KS_MIB_TOTAL_TX_2		0x109
+#define KS_MIB_PACKET_DROPPED_TX_2	0x10A
+#define KS_MIB_PACKET_DROPPED_RX_2	0x10B
+#define KS_MIB_TOTAL_RX_3		0x10C
+#define KS_MIB_TOTAL_TX_3		0x10D
+#define KS_MIB_PACKET_DROPPED_TX_3	0x10E
+#define KS_MIB_PACKET_DROPPED_RX_3	0x10F
+#define KS_MIB_TOTAL_RX_4		0x110
+#define KS_MIB_TOTAL_TX_4		0x111
+#define KS_MIB_PACKET_DROPPED_TX_4	0x112
+#define KS_MIB_PACKET_DROPPED_RX_4	0x113
+
+#define MIB_PACKET_DROPPED		0x0000FFFF
+
+#define MIB_TOTAL_BYTES_H		0x0000000F
+
+#define TAIL_TAG_OVERRIDE		BIT(6)
+#define TAIL_TAG_LOOKUP			BIT(7)
+
+#define VLAN_TABLE_ENTRIES		(4096 / 4)
+#define FID_ENTRIES			128
+
+#endif

drivers/net/dsa/microchip/ksz8795_spi.c

+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Microchip KSZ8795 series register access through SPI
+ *
+ * Copyright (C) 2017 Microchip Technology Inc.
+ *	Tristram Ha <Tristram.Ha@microchip.com>
+ */
+
+#include <asm/unaligned.h>
+
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/spi/spi.h>
+
+#include "ksz_priv.h"
+#include "ksz_common.h"
+
+#define SPI_ADDR_SHIFT			12
+#define SPI_ADDR_ALIGN			3
+#define SPI_TURNAROUND_SHIFT		1
+
+KSZ_REGMAP_TABLE(ksz8795, 16, SPI_ADDR_SHIFT,
+		 SPI_TURNAROUND_SHIFT, SPI_ADDR_ALIGN);
+
+static int ksz8795_spi_probe(struct spi_device *spi)
+{
+	struct ksz_device *dev;
+	int i, ret;
+
+	dev = ksz_switch_alloc(&spi->dev, spi);
+	if (!dev)
+		return -ENOMEM;
+
+	for (i = 0; i < ARRAY_SIZE(ksz8795_regmap_config); i++) {
+		dev->regmap[i] = devm_regmap_init_spi(spi,
+						      &ksz8795_regmap_config
+						      [i]);
+		if (IS_ERR(dev->regmap[i])) {
+			ret = PTR_ERR(dev->regmap[i]);
+			dev_err(&spi->dev,
+				"Failed to initialize regmap%i: %d\n",
+				ksz8795_regmap_config[i].val_bits, ret);
+			return ret;
+		}
+	}
+
+	if (spi->dev.platform_data)
+		dev->pdata = spi->dev.platform_data;
+
+	ret = ksz8795_switch_register(dev);
+
+	/* Main DSA driver may not be started yet. */
+	if (ret)
+		return ret;
+
+	spi_set_drvdata(spi, dev);
+
+	return 0;
+}
+
+static int ksz8795_spi_remove(struct spi_device *spi)
+{
+	struct ksz_device *dev = spi_get_drvdata(spi);
+
+	if (dev)
+		ksz_switch_remove(dev);
+
+	return 0;
+}
+
+static void ksz8795_spi_shutdown(struct spi_device *spi)
+{
+	struct ksz_device *dev = spi_get_drvdata(spi);
+
+	if (dev && dev->dev_ops->shutdown)
+		dev->dev_ops->shutdown(dev);
+}
+
+static const struct of_device_id ksz8795_dt_ids[] = {
+	{ .compatible = "microchip,ksz8765" },
+	{ .compatible = "microchip,ksz8794" },
+	{ .compatible = "microchip,ksz8795" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, ksz8795_dt_ids);
+
+static struct spi_driver ksz8795_spi_driver = {
+	.driver = {
+		.name	= "ksz8795-switch",
+		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(ksz8795_dt_ids),
+	},
+	.probe	= ksz8795_spi_probe,
+	.remove	= ksz8795_spi_remove,
+	.shutdown = ksz8795_spi_shutdown,
+};
+
+module_spi_driver(ksz8795_spi_driver);
+
+MODULE_AUTHOR("Tristram Ha <Tristram.Ha@microchip.com>");
+MODULE_DESCRIPTION("Microchip KSZ8795 Series Switch SPI Driver");
+MODULE_LICENSE("GPL");

drivers/net/dsa/microchip/ksz_common.c

@@ -373,6 +373,7 @@ int ksz_enable_port(struct dsa_switch *ds, int port, struct phy_device *phy)
 
 	/* setup slave port */
 	dev->dev_ops->port_setup(dev, port, false);
+	if (dev->dev_ops->phy_setup)
 		dev->dev_ops->phy_setup(dev, port, phy);
 
 	/* port_stp_state_set() will be called after to enable the port so

drivers/net/dsa/microchip/ksz_common.h

@@ -68,6 +68,22 @@ static inline int ksz_read32(struct ksz_device *dev, u32 reg, u32 *val)
 	return ret;
 }
 
+static inline int ksz_read64(struct ksz_device *dev, u32 reg, u64 *val)
+{
+	u32 value[2];
+	int ret;
+
+	ret = regmap_bulk_read(dev->regmap[2], reg, value, 2);
+	if (!ret) {
+		/* Ick! ToDo: Add 64bit R/W to regmap on 32bit systems */
+		value[0] = swab32(value[0]);
+		value[1] = swab32(value[1]);
+		*val = swab64((u64)*value);
+	}
+
+	return ret;
+}
+
 static inline int ksz_write8(struct ksz_device *dev, u32 reg, u8 value)
 {
 	return regmap_write(dev->regmap[0], reg, value);
@@ -83,6 +99,18 @@ static inline int ksz_write32(struct ksz_device *dev, u32 reg, u32 value)
 	return regmap_write(dev->regmap[2], reg, value);
 }
 
+static inline int ksz_write64(struct ksz_device *dev, u32 reg, u64 value)
+{
+	u32 val[2];
+
+	/* Ick! ToDo: Add 64bit R/W to regmap on 32bit systems */
+	value = swab64(value);
+	val[0] = swab32(value & 0xffffffffULL);
+	val[1] = swab32(value >> 32ULL);
+
+	return regmap_bulk_write(dev->regmap[2], reg, val, 2);
+}
+
 static inline void ksz_pread8(struct ksz_device *dev, int port, int offset,
 			      u8 *data)
 {

drivers/net/dsa/microchip/ksz_priv.h

@@ -150,6 +150,7 @@ int ksz_switch_register(struct ksz_device *dev,
 			const struct ksz_dev_ops *ops);
 void ksz_switch_remove(struct ksz_device *dev);
 
+int ksz8795_switch_register(struct ksz_device *dev);
 int ksz9477_switch_register(struct ksz_device *dev);
 
 #endif

include/net/dsa.h

@@ -41,6 +41,7 @@ struct phylink_link_state;
 #define DSA_TAG_PROTO_TRAILER_VALUE		11
 #define DSA_TAG_PROTO_8021Q_VALUE		12
 #define DSA_TAG_PROTO_SJA1105_VALUE		13
+#define DSA_TAG_PROTO_KSZ8795_VALUE		14
 
 enum dsa_tag_protocol {
 	DSA_TAG_PROTO_NONE		= DSA_TAG_PROTO_NONE_VALUE,
@@ -57,6 +58,7 @@ enum dsa_tag_protocol {
 	DSA_TAG_PROTO_TRAILER		= DSA_TAG_PROTO_TRAILER_VALUE,
 	DSA_TAG_PROTO_8021Q		= DSA_TAG_PROTO_8021Q_VALUE,
 	DSA_TAG_PROTO_SJA1105		= DSA_TAG_PROTO_SJA1105_VALUE,
+	DSA_TAG_PROTO_KSZ8795		= DSA_TAG_PROTO_KSZ8795_VALUE,
 };
 
 struct packet_type;

net/dsa/tag_ksz.c

@@ -69,6 +69,67 @@ static struct sk_buff *ksz_common_rcv(struct sk_buff *skb,
 	return skb;
 }
 
+/*
+ * For Ingress (Host -> KSZ8795), 1 byte is added before FCS.
+ * ---------------------------------------------------------------------------
+ * DA(6bytes)|SA(6bytes)|....|Data(nbytes)|tag(1byte)|FCS(4bytes)
+ * ---------------------------------------------------------------------------
+ * tag : each bit represents port (eg, 0x01=port1, 0x02=port2, 0x10=port5)
+ *
+ * For Egress (KSZ8795 -> Host), 1 byte is added before FCS.
+ * ---------------------------------------------------------------------------
+ * DA(6bytes)|SA(6bytes)|....|Data(nbytes)|tag0(1byte)|FCS(4bytes)
+ * ---------------------------------------------------------------------------
+ * tag0 : zero-based value represents port
+ *	  (eg, 0x00=port1, 0x02=port3, 0x06=port7)
+ */
+
+#define KSZ8795_INGRESS_TAG_LEN		1
+
+#define KSZ8795_TAIL_TAG_OVERRIDE	BIT(6)
+#define KSZ8795_TAIL_TAG_LOOKUP		BIT(7)
+
+static struct sk_buff *ksz8795_xmit(struct sk_buff *skb, struct net_device *dev)
+{
+	struct dsa_port *dp = dsa_slave_to_port(dev);
+	struct sk_buff *nskb;
+	u8 *tag;
+	u8 *addr;
+
+	nskb = ksz_common_xmit(skb, dev, KSZ8795_INGRESS_TAG_LEN);
+	if (!nskb)
+		return NULL;
+
+	/* Tag encoding */
+	tag = skb_put(nskb, KSZ8795_INGRESS_TAG_LEN);
+	addr = skb_mac_header(nskb);
+
+	*tag = 1 << dp->index;
+	if (is_link_local_ether_addr(addr))
+		*tag |= KSZ8795_TAIL_TAG_OVERRIDE;
+
+	return nskb;
+}
+
+static struct sk_buff *ksz8795_rcv(struct sk_buff *skb, struct net_device *dev,
+				  struct packet_type *pt)
+{
+	u8 *tag = skb_tail_pointer(skb) - KSZ_EGRESS_TAG_LEN;
+
+	return ksz_common_rcv(skb, dev, tag[0] & 7, KSZ_EGRESS_TAG_LEN);
+}
+
+static const struct dsa_device_ops ksz8795_netdev_ops = {
+	.name	= "ksz8795",
+	.proto	= DSA_TAG_PROTO_KSZ8795,
+	.xmit	= ksz8795_xmit,
+	.rcv	= ksz8795_rcv,
+	.overhead = KSZ8795_INGRESS_TAG_LEN,
+};
+
+DSA_TAG_DRIVER(ksz8795_netdev_ops);
+MODULE_ALIAS_DSA_TAG_DRIVER(DSA_TAG_PROTO_KSZ8795);
+
 /*
  * For Ingress (Host -> KSZ9477), 2 bytes are added before FCS.
  * ---------------------------------------------------------------------------
@@ -183,6 +244,7 @@ DSA_TAG_DRIVER(ksz9893_netdev_ops);
 MODULE_ALIAS_DSA_TAG_DRIVER(DSA_TAG_PROTO_KSZ9893);
 
 static struct dsa_tag_driver *dsa_tag_driver_array[] = {
+	&DSA_TAG_DRIVER_NAME(ksz8795_netdev_ops),
 	&DSA_TAG_DRIVER_NAME(ksz9477_netdev_ops),
 	&DSA_TAG_DRIVER_NAME(ksz9893_netdev_ops),
 };