Merge tag 'usb-6.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB fixes from Greg KH:
 "Here are a handful of small USB fixes for 6.11-rc7. Included in here
  are:

   - dwc3 driver fixes for two reported problems

   - two typec ucsi driver fixes

   - cdns2 controller reset fix

  All of these have been in linux-next this week with no reported
  problems"

* tag 'usb-6.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: typec: ucsi: Fix cable registration
  usb: typec: ucsi: Fix the partner PD revision
  usb: cdns2: Fix controller reset issue
  usb: dwc3: core: update LC timer as per USB Spec V3.2
  usb: dwc3: Avoid waking up gadget during startxfer

drivers/usb/dwc3/core.c

@@ -1386,6 +1386,21 @@ static int dwc3_core_init(struct dwc3 *dwc)
 		dwc3_writel(dwc->regs, DWC3_GUCTL2, reg);
 	}
 
+	/*
+	 * STAR 9001285599: This issue affects DWC_usb3 version 3.20a
+	 * only. If the PM TIMER ECM is enabled through GUCTL2[19], the
+	 * link compliance test (TD7.21) may fail. If the ECN is not
+	 * enabled (GUCTL2[19] = 0), the controller will use the old timer
+	 * value (5us), which is still acceptable for the link compliance
+	 * test. Therefore, do not enable PM TIMER ECM in 3.20a by
+	 * setting GUCTL2[19] by default; instead, use GUCTL2[19] = 0.
+	 */
+	if (DWC3_VER_IS(DWC3, 320A)) {
+		reg = dwc3_readl(dwc->regs, DWC3_GUCTL2);
+		reg &= ~DWC3_GUCTL2_LC_TIMER;
+		dwc3_writel(dwc->regs, DWC3_GUCTL2, reg);
+	}
+
 	/*
 	 * When configured in HOST mode, after issuing U3/L2 exit controller
 	 * fails to send proper CRC checksum in CRC5 feild. Because of this

drivers/usb/dwc3/core.h

@@ -421,6 +421,7 @@
 
 /* Global User Control Register 2 */
 #define DWC3_GUCTL2_RST_ACTBITLATER		BIT(14)
+#define DWC3_GUCTL2_LC_TIMER			BIT(19)
 
 /* Global User Control Register 3 */
 #define DWC3_GUCTL3_SPLITDISABLE		BIT(14)
@@ -1269,6 +1270,7 @@ struct dwc3 {
 #define DWC3_REVISION_290A	0x5533290a
 #define DWC3_REVISION_300A	0x5533300a
 #define DWC3_REVISION_310A	0x5533310a
+#define DWC3_REVISION_320A	0x5533320a
 #define DWC3_REVISION_330A	0x5533330a
 
 #define DWC31_REVISION_ANY	0x0

drivers/usb/dwc3/gadget.c

@@ -287,6 +287,23 @@ static int __dwc3_gadget_wakeup(struct dwc3 *dwc, bool async);
  *
  * Caller should handle locking. This function will issue @cmd with given
  * @params to @dep and wait for its completion.
+ *
+ * According to the programming guide, if the link state is in L1/L2/U3,
+ * then sending the Start Transfer command may not complete. The
+ * programming guide suggested to bring the link state back to ON/U0 by
+ * performing remote wakeup prior to sending the command. However, don't
+ * initiate remote wakeup when the user/function does not send wakeup
+ * request via wakeup ops. Send the command when it's allowed.
+ *
+ * Notes:
+ * For L1 link state, issuing a command requires the clearing of
+ * GUSB2PHYCFG.SUSPENDUSB2, which turns on the signal required to complete
+ * the given command (usually within 50us). This should happen within the
+ * command timeout set by driver. No additional step is needed.
+ *
+ * For L2 or U3 link state, the gadget is in USB suspend. Care should be
+ * taken when sending Start Transfer command to ensure that it's done after
+ * USB resume.
  */
 int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned int cmd,
 		struct dwc3_gadget_ep_cmd_params *params)
@@ -327,30 +344,6 @@ int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned int cmd,
 			dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
 	}
 
-	if (DWC3_DEPCMD_CMD(cmd) == DWC3_DEPCMD_STARTTRANSFER) {
-		int link_state;
-
-		/*
-		 * Initiate remote wakeup if the link state is in U3 when
-		 * operating in SS/SSP or L1/L2 when operating in HS/FS. If the
-		 * link state is in U1/U2, no remote wakeup is needed. The Start
-		 * Transfer command will initiate the link recovery.
-		 */
-		link_state = dwc3_gadget_get_link_state(dwc);
-		switch (link_state) {
-		case DWC3_LINK_STATE_U2:
-			if (dwc->gadget->speed >= USB_SPEED_SUPER)
-				break;
-
-			fallthrough;
-		case DWC3_LINK_STATE_U3:
-			ret = __dwc3_gadget_wakeup(dwc, false);
-			dev_WARN_ONCE(dwc->dev, ret, "wakeup failed --> %d\n",
-					ret);
-			break;
-		}
-	}
-
 	/*
 	 * For some commands such as Update Transfer command, DEPCMDPARn
 	 * registers are reserved. Since the driver often sends Update Transfer

drivers/usb/gadget/udc/cdns2/cdns2-gadget.c

@@ -2251,7 +2251,6 @@ static int cdns2_gadget_start(struct cdns2_device *pdev)
 {
 	u32 max_speed;
 	void *buf;
-	int val;
 	int ret;
 
 	pdev->usb_regs = pdev->regs;
@@ -2261,14 +2260,9 @@ static int cdns2_gadget_start(struct cdns2_device *pdev)
 	pdev->adma_regs = pdev->regs + CDNS2_ADMA_REGS_OFFSET;
 
 	/* Reset controller. */
-	set_reg_bit_8(&pdev->usb_regs->cpuctrl, CPUCTRL_SW_RST);
-
-	ret = readl_poll_timeout_atomic(&pdev->usb_regs->cpuctrl, val,
-					!(val & CPUCTRL_SW_RST), 1, 10000);
-	if (ret) {
-		dev_err(pdev->dev, "Error: reset controller timeout\n");
-		return -EINVAL;
-	}
+	writeb(CPUCTRL_SW_RST | CPUCTRL_UPCLK | CPUCTRL_WUEN,
+	       &pdev->usb_regs->cpuctrl);
+	usleep_range(5, 10);
 
 	usb_initialize_gadget(pdev->dev, &pdev->gadget, NULL);
 

drivers/usb/gadget/udc/cdns2/cdns2-gadget.h

@@ -292,8 +292,17 @@ struct cdns2_usb_regs {
 #define SPEEDCTRL_HSDISABLE	BIT(7)
 
 /* CPUCTRL- bitmasks. */
+/* UP clock enable */
+#define CPUCTRL_UPCLK		BIT(0)
 /* Controller reset bit. */
 #define CPUCTRL_SW_RST		BIT(1)
+/**
+ * If the wuen bit is ‘1’, the upclken is automatically set to ‘1’ after
+ * detecting rising edge of wuintereq interrupt. If the wuen bit is ‘0’,
+ * the wuintereq interrupt is ignored.
+ */
+#define CPUCTRL_WUEN		BIT(7)
+
 
 /**
  * struct cdns2_adma_regs - ADMA controller registers.

drivers/usb/typec/ucsi/ucsi.c

@@ -965,10 +965,20 @@ static void ucsi_unregister_plug(struct ucsi_connector *con)
 
 static int ucsi_register_cable(struct ucsi_connector *con)
 {
+	struct ucsi_cable_property cable_prop;
 	struct typec_cable *cable;
 	struct typec_cable_desc desc = {};
+	u64 command;
+	int ret;
+
+	command = UCSI_GET_CABLE_PROPERTY | UCSI_CONNECTOR_NUMBER(con->num);
+	ret = ucsi_send_command(con->ucsi, command, &cable_prop, sizeof(cable_prop));
+	if (ret < 0) {
+		dev_err(con->ucsi->dev, "GET_CABLE_PROPERTY failed (%d)\n", ret);
+		return ret;
+	}
 
-	switch (UCSI_CABLE_PROP_FLAG_PLUG_TYPE(con->cable_prop.flags)) {
+	switch (UCSI_CABLE_PROP_FLAG_PLUG_TYPE(cable_prop.flags)) {
 	case UCSI_CABLE_PROPERTY_PLUG_TYPE_A:
 		desc.type = USB_PLUG_TYPE_A;
 		break;
@@ -984,10 +994,10 @@ static int ucsi_register_cable(struct ucsi_connector *con)
 	}
 
 	desc.identity = &con->cable_identity;
-	desc.active = !!(UCSI_CABLE_PROP_FLAG_ACTIVE_CABLE &
-			 con->cable_prop.flags);
-	desc.pd_revision = UCSI_CABLE_PROP_FLAG_PD_MAJOR_REV_AS_BCD(
-	    con->cable_prop.flags);
+	desc.active = !!(UCSI_CABLE_PROP_FLAG_ACTIVE_CABLE & cable_prop.flags);
+
+	if (con->ucsi->version >= UCSI_VERSION_2_1)
+		desc.pd_revision = UCSI_CABLE_PROP_FLAG_PD_MAJOR_REV_AS_BCD(cable_prop.flags);
 
 	cable = typec_register_cable(con->port, &desc);
 	if (IS_ERR(cable)) {
@@ -1012,6 +1022,27 @@ static void ucsi_unregister_cable(struct ucsi_connector *con)
 	con->cable = NULL;
 }
 
+static int ucsi_check_connector_capability(struct ucsi_connector *con)
+{
+	u64 command;
+	int ret;
+
+	if (!con->partner || con->ucsi->version < UCSI_VERSION_2_1)
+		return 0;
+
+	command = UCSI_GET_CONNECTOR_CAPABILITY | UCSI_CONNECTOR_NUMBER(con->num);
+	ret = ucsi_send_command(con->ucsi, command, &con->cap, sizeof(con->cap));
+	if (ret < 0) {
+		dev_err(con->ucsi->dev, "GET_CONNECTOR_CAPABILITY failed (%d)\n", ret);
+		return ret;
+	}
+
+	typec_partner_set_pd_revision(con->partner,
+		UCSI_CONCAP_FLAG_PARTNER_PD_MAJOR_REV_AS_BCD(con->cap.flags));
+
+	return ret;
+}
+
 static void ucsi_pwr_opmode_change(struct ucsi_connector *con)
 {
 	switch (UCSI_CONSTAT_PWR_OPMODE(con->status.flags)) {
@@ -1021,6 +1052,7 @@ static void ucsi_pwr_opmode_change(struct ucsi_connector *con)
 		ucsi_partner_task(con, ucsi_get_src_pdos, 30, 0);
 		ucsi_partner_task(con, ucsi_check_altmodes, 30, HZ);
 		ucsi_partner_task(con, ucsi_register_partner_pdos, 1, HZ);
+		ucsi_partner_task(con, ucsi_check_connector_capability, 1, HZ);
 		break;
 	case UCSI_CONSTAT_PWR_OPMODE_TYPEC1_5:
 		con->rdo = 0;
@@ -1064,7 +1096,6 @@ static int ucsi_register_partner(struct ucsi_connector *con)
 
 	desc.identity = &con->partner_identity;
 	desc.usb_pd = pwr_opmode == UCSI_CONSTAT_PWR_OPMODE_PD;
-	desc.pd_revision = UCSI_CONCAP_FLAG_PARTNER_PD_MAJOR_REV_AS_BCD(con->cap.flags);
 
 	partner = typec_register_partner(con->port, &desc);
 	if (IS_ERR(partner)) {
@@ -1141,27 +1172,6 @@ static void ucsi_partner_change(struct ucsi_connector *con)
 			con->num, u_role);
 }
 
-static int ucsi_check_connector_capability(struct ucsi_connector *con)
-{
-	u64 command;
-	int ret;
-
-	if (!con->partner || con->ucsi->version < UCSI_VERSION_2_0)
-		return 0;
-
-	command = UCSI_GET_CONNECTOR_CAPABILITY | UCSI_CONNECTOR_NUMBER(con->num);
-	ret = ucsi_send_command(con->ucsi, command, &con->cap, sizeof(con->cap));
-	if (ret < 0) {
-		dev_err(con->ucsi->dev, "GET_CONNECTOR_CAPABILITY failed (%d)\n", ret);
-		return ret;
-	}
-
-	typec_partner_set_pd_revision(con->partner,
-		UCSI_CONCAP_FLAG_PARTNER_PD_MAJOR_REV_AS_BCD(con->cap.flags));
-
-	return ret;
-}
-
 static int ucsi_check_connection(struct ucsi_connector *con)
 {
 	u8 prev_flags = con->status.flags;
@@ -1193,21 +1203,11 @@ static int ucsi_check_connection(struct ucsi_connector *con)
 
 static int ucsi_check_cable(struct ucsi_connector *con)
 {
-	u64 command;
 	int ret, num_plug_am;
 
 	if (con->cable)
 		return 0;
 
-	command = UCSI_GET_CABLE_PROPERTY | UCSI_CONNECTOR_NUMBER(con->num);
-	ret = ucsi_send_command(con->ucsi, command, &con->cable_prop,
-				sizeof(con->cable_prop));
-	if (ret < 0) {
-		dev_err(con->ucsi->dev, "GET_CABLE_PROPERTY failed (%d)\n",
-			ret);
-		return ret;
-	}
-
 	ret = ucsi_register_cable(con);
 	if (ret < 0)
 		return ret;
@@ -1283,15 +1283,16 @@ static void ucsi_handle_connector_change(struct work_struct *work)
 		if (con->status.flags & UCSI_CONSTAT_CONNECTED) {
 			ucsi_register_partner(con);
 			ucsi_partner_task(con, ucsi_check_connection, 1, HZ);
-			ucsi_partner_task(con, ucsi_check_connector_capability, 1, HZ);
 			if (con->ucsi->cap.features & UCSI_CAP_GET_PD_MESSAGE)
 				ucsi_partner_task(con, ucsi_get_partner_identity, 1, HZ);
 			if (con->ucsi->cap.features & UCSI_CAP_CABLE_DETAILS)
 				ucsi_partner_task(con, ucsi_check_cable, 1, HZ);
 
 			if (UCSI_CONSTAT_PWR_OPMODE(con->status.flags) ==
-			    UCSI_CONSTAT_PWR_OPMODE_PD)
+			    UCSI_CONSTAT_PWR_OPMODE_PD) {
 				ucsi_partner_task(con, ucsi_register_partner_pdos, 1, HZ);
+				ucsi_partner_task(con, ucsi_check_connector_capability, 1, HZ);
+			}
 		} else {
 			ucsi_unregister_partner(con);
 		}
@@ -1706,6 +1707,7 @@ static int ucsi_register_port(struct ucsi *ucsi, struct ucsi_connector *con)
 		ucsi_register_device_pdos(con);
 		ucsi_get_src_pdos(con);
 		ucsi_check_altmodes(con);
+		ucsi_check_connector_capability(con);
 	}
 
 	trace_ucsi_register_port(con->num, &con->status);

drivers/usb/typec/ucsi/ucsi.h

@@ -465,7 +465,6 @@ struct ucsi_connector {
 
 	struct ucsi_connector_status status;
 	struct ucsi_connector_capability cap;
-	struct ucsi_cable_property cable_prop;
 	struct power_supply *psy;
 	struct power_supply_desc psy_desc;
 	u32 rdo;