Merge bk://kernel.bkbits.net/gregkh/linux/usb-2.6

into ppc970.osdl.org:/home/torvalds/v2.6/linux

Documentation/usb/philips.txt

-This file contains some additional information for the Philips webcams.
-E-mail: webcam@smcc.demon.nl                        Last updated: 2001-09-24
-
-The main webpage for the Philips driver is http://www.smcc.demon.nl/webcam/.
-It contains a lot of extra information, a FAQ, and the binary plugin
-'PWCX'. This plugin contains decompression routines that allow you to
-use higher image sizes and framerates; in addition the webcam uses less
-bandwidth on the USB bus (handy if you want to run more than 1 camera
-simultaneously). These routines fall under an NDA, and may therefor not be
-distributed as source; however, its use is completely optional.
+This file contains some additional information for the Philips and OEM webcams.
+E-mail: webcam@smcc.demon.nl                        Last updated: 2004-01-19
+Site: http://www.smcc.demon.nl/webcam/
+
+As of this moment, the following cameras are supported:
+ * Philips PCA645
+ * Philips PCA646
+ * Philips PCVC675
+ * Philips PCVC680
+ * Philips PCVC690
+ * Philips PCVC720/40
+ * Philips PCVC730
+ * Philips PCVC740
+ * Philips PCVC750
+ * Askey VC010
+ * Creative Labs Webcam 5
+ * Creative Labs Webcam Pro Ex
+ * Logitech QuickCam 3000 Pro
+ * Logitech QuickCam 4000 Pro
+ * Logitech QuickCam Notebook Pro
+ * Logitech QuickCam Zoom
+ * Logitech QuickCam Orbit
+ * Logitech QuickCam Sphere
+ * Samsung MPC-C10
+ * Samsung MPC-C30
+ * Sotec Afina Eye
+ * AME CU-001
+ * Visionite VCS-UM100
+ * Visionite VCS-UC300
+
+The main webpage for the Philips driver is at the address above. It contains
+a lot of extra information, a FAQ, and the binary plugin 'PWCX'. This plugin
+contains decompression routines that allow you to use higher image sizes and
+framerates; in addition the webcam uses less bandwidth on the USB bus (handy
+if you want to run more than 1 camera simultaneously). These routines fall
+under a NDA, and may therefor not be distributed as source; however, its use
+is completely optional.
 
 You can build this code either into your kernel, or as a module. I recommend
 the latter, since it makes troubleshooting a lot easier. The built-in
@@ -27,14 +54,14 @@ fps
    Specifies the desired framerate. Is an integer in the range of 4-30.
 
 fbufs
-   This parameter specifies the number of internal buffers to use for storing 
+   This paramter specifies the number of internal buffers to use for storing 
    frames from the cam. This will help if the process that reads images from 
-   the cam is a bit slow or momentarily busy. However, on slow machines it
+   the cam is a bit slow or momentarely busy. However, on slow machines it 
    only introduces lag, so choose carefully. The default is 3, which is 
    reasonable. You can set it between 2 and 5.
 
 mbufs
-   This is an integer between 1 and 4. It will tell the module the number of
+   This is an integer between 1 and 10. It will tell the module the number of
    buffers to reserve for mmap(), VIDIOCCGMBUF, VIDIOCMCAPTURE and friends.
    The default is 2, which is adequate for most applications (double
    buffering).
@@ -45,9 +72,9 @@ mbufs
    slack when your program is behind. But you need a multi-threaded or
    forked program to really take advantage of these buffers.
 
-   The absolute maximum is 4, but don't set it too high!  Every buffer takes
-   up 1.22 MB of RAM, so unless you have a lot of memory setting this to
-   something more than 2 is an absolute waste.  This memory is only
+   The absolute maximum is 10, but don't set it too high!  Every buffer takes
+   up 460 KB of RAM, so unless you have a lot of memory setting this to
+   something more than 4 is an absolute waste.  This memory is only
    allocated during open(), so nothing is wasted when the camera is not in
    use.
 
@@ -75,8 +102,9 @@ compression (only useful with the plugin)
    See the FAQ on the website for an overview of which modes require
    compression.
 
-   The compression parameter only applies to the Vesta & ToUCam cameras.
-   The 645 and 646 have fixed compression parameters.      
+   The compression parameter does not apply to the 645 and 646 cameras
+   and OEM models derived from those (only a few). Most cams honour this
+   parameter.
 
 leds
    This settings takes 2 integers, that define the on/off time for the LED
@@ -89,14 +117,17 @@ leds
 
      leds=0,0
 
-   the LED never goes on, making it suitable for silent survaillance.
+   the LED never goes on, making it suitable for silent surveillance.
 
    By default the camera's LED is on solid while in use, and turned off
    when the camera is not used anymore.
 
-   This parameter works only with the ToUCam range of cameras (730, 740,
-   750). For other cameras this command is silently ignored, and the LED
-   cannot be controlled.
+   This parameter works only with the ToUCam range of cameras (720, 730, 740,
+   750) and OEMs. For other cameras this command is silently ignored, and 
+   the LED cannot be controlled.
+
+   Finally: this parameters does not take effect UNTIL the first time you
+   open the camera device. Until then, the LED remains on.
 
 dev_hint
    A long standing problem with USB devices is their dynamic nature: you
@@ -126,7 +157,7 @@ dev_hint
                                other cameras will get the first free 
                                available slot (see below).
 
-     dev_hint=645:1,680=2      The PCA645 camera will get /dev/video1,
+     dev_hint=645:1,680:2      The PCA645 camera will get /dev/video1,
                                and a PCVC680 /dev/video2.
                                
      dev_hint=645.0123:3,645.4567:0	The PCA645 camera with serialnumber 
@@ -176,13 +207,16 @@ trace
 
       64   0x40   Show viewport and image sizes                       Off
 
+     128   0x80   PWCX debugging                                      Off
 
    For example, to trace the open() & read() fuctions, sum 8 + 4 = 12,
    so you would supply trace=12 during insmod or modprobe. If
    you want to turn the initialization and probing tracing off, set trace=0.
    The default value for trace is 35 (0x23).
 
-   Example:
+
+
+Example:
      
      # modprobe pwc size=cif fps=15 power_save=1
 
@@ -192,7 +226,7 @@ cameras. Each camera has its own set of buffers.
 size and fps only specify defaults when you open() the device; this is to
 accommodate some tools that don't set the size. You can change these
 settings after open() with the Video4Linux ioctl() calls. The default of
-defaults is QCIF size at 10 fps, BGR order.
+defaults is QCIF size at 10 fps.
 
 The compression parameter is semiglobal; it sets the initial compression
 preference for all camera's, but this parameter can be set per camera with
@@ -200,4 +234,3 @@ the VIDIOCPWCSCQUAL ioctl() call.
 
 All parameters are optional.
 
-

drivers/usb/class/cdc-acm.h

@@ -86,17 +86,23 @@ struct acm {
 	struct usb_interface *data;			/* data interface */
 	struct tty_struct *tty;				/* the corresponding tty */
 	struct urb *ctrlurb, *readurb, *writeurb;	/* urbs */
+	u8 *ctrl_buffer, *read_buffer, *write_buffer;	/* buffers of urbs */
+	dma_addr_t ctrl_dma, read_dma, write_dma;	/* dma handles of buffers */
 	struct acm_line line;				/* line coding (bits, stop, parity) */
 	struct work_struct work;			/* work queue entry for line discipline waking up */
 	struct tasklet_struct bh;			/* rx processing */
+	spinlock_t throttle_lock;			/* synchronize throtteling and read callback */
 	unsigned int ctrlin;				/* input control lines (DCD, DSR, RI, break, overruns) */
 	unsigned int ctrlout;				/* output control lines (DTR, RTS) */
 	unsigned int writesize;				/* max packet size for the output bulk endpoint */
+	unsigned int readsize,ctrlsize;			/* buffer sizes for freeing */
 	unsigned int used;				/* someone has this acm's device open */
 	unsigned int minor;				/* acm minor number */
 	unsigned char throttle;				/* throttled by tty layer */
 	unsigned char clocal;				/* termios CLOCAL */
 	unsigned char ready_for_write;			/* write urb can be used */
+	unsigned char resubmit_to_unthrottle;		/* throtteling has disabled the read urb */
+	unsigned int ctrl_caps;				/* control capabilities from the class specific header */
 };
 
 /* "Union Functional Descriptor" from CDC spec 5.2.3.X */
@@ -110,6 +116,12 @@ struct union_desc {
 	/* ... and there could be other slave interfaces */
 } __attribute__ ((packed));
 
+/* class specific descriptor types */
+#define CDC_CALL_MANAGEMENT_TYPE	0x01
+#define CDC_AC_MANAGEMENT_TYPE		0x02
 #define CDC_UNION_TYPE			0x06
+#define CDC_COUNTRY_TYPE		0x07
+
 #define CDC_DATA_INTERFACE_TYPE	0x0a
 
+

drivers/usb/core/hub.c

@@ -1034,7 +1034,7 @@ static inline void show_string(struct usb_device *udev, char *id, int index)
 {}
 #endif
 
-/*
+/**
  * usb_new_device - perform initial device setup (usbcore-internal)
  * @udev: newly addressed device (in ADDRESS state)
  *
@@ -1333,13 +1333,14 @@ static int hub_set_address(struct usb_device *udev)
 	return retval;
 }
 
-/* reset device, (re)assign address, get device descriptor.
- * device connection is stable, no more debouncing needed.
- * returns device in USB_STATE_ADDRESS, except on error.
- * on error return, device is no longer usable (ref dropped).
+/* Reset device, (re)assign address, get device descriptor.
+ * Device connection must be stable, no more debouncing needed.
+ * Returns device in USB_STATE_ADDRESS, except on error.
  *
- * caller owns dev->serialize for the device, guarding against
- * config changes and disconnect processing.
+ * If this is called for an already-existing device (as part of
+ * usb_reset_device), the caller must own the device lock.  For a
+ * newly detected device that is not accessible through any global
+ * pointers, it's not necessary to lock the device.
  */
 static int
 hub_port_init (struct usb_device *hdev, struct usb_device *udev, int port)
@@ -1571,6 +1572,7 @@ static void hub_port_connect_change(struct usb_hub *hub, int port,
 	/* Disconnect any existing devices under this port */
 	if (hdev->children[port])
 		usb_disconnect(&hdev->children[port]);
+	clear_bit(port, hub->change_bits);
 
 	if (portchange & USB_PORT_STAT_C_CONNECTION) {
 		status = hub_port_debounce(hdev, port);
@@ -1785,12 +1787,15 @@ static void hub_events(void)
 
 		/* deal with port status changes */
 		for (i = 0; i < hub->descriptor->bNbrPorts; i++) {
-			if (!test_and_clear_bit(i+1, hub->event_bits))
+			connect_change = test_bit(i, hub->change_bits);
+			if (!test_and_clear_bit(i+1, hub->event_bits) &&
+					!connect_change)
 				continue;
-			ret = hub_port_status(hdev, i, &portstatus, &portchange);
+
+			ret = hub_port_status(hdev, i,
+					&portstatus, &portchange);
 			if (ret < 0)
 				continue;
-			connect_change = 0;
 
 			if (portchange & USB_PORT_STAT_C_CONNECTION) {
 				clear_port_feature(hdev,
@@ -1819,7 +1824,7 @@ static void hub_events(void)
 					dev_err (hub_dev,
 					    "port %i "
 					    "disabled by hub (EMI?), "
-					    "re-enabling...",
+					    "re-enabling...\n",
 						i + 1);
 					connect_change = 1;
 				}
@@ -1996,23 +2001,34 @@ static int config_descriptors_changed(struct usb_device *udev)
 				!= 0) {
 			dev_dbg(&udev->dev, "config index %d changed (#%d)\n",
 				index, buf->bConfigurationValue);
-/* FIXME enable this when we can re-enumerate after reset;
- * until then DFU-ish drivers need this and other workarounds
- */
-//			break;
+			break;
 		}
 	}
 	kfree(buf);
 	return index != udev->descriptor.bNumConfigurations;
 }
 
-/*
+/**
+ * usb_reset_devce - perform a USB port reset to reinitialize a device
+ * @udev: device to reset (not in SUSPENDED or NOTATTACHED state)
+ *
  * WARNING - don't reset any device unless drivers for all of its
  * interfaces are expecting that reset!  Maybe some driver->reset()
  * method should eventually help ensure sufficient cooperation.
  *
- * This is the same as usb_reset_device() except that the caller
- * already holds dev->serialize.  For example, it's safe to use
+ * Do a port reset, reassign the device's address, and establish its
+ * former operating configuration.  If the reset fails, or the device's
+ * descriptors change from their values before the reset, or the original
+ * configuration and altsettings cannot be restored, a flag will be set
+ * telling khubd to pretend the device has been disconnected and then
+ * re-connected.  All drivers will be unbound, and the device will be
+ * re-enumerated and probed all over again.
+ *
+ * Returns 0 if the reset succeeded, -ENODEV if the device has been
+ * flagged for logical disconnection, or some other negative error code
+ * if the reset wasn't even attempted.
+ *
+ * The caller must own the device lock.  For example, it's safe to use
  * this from a driver probe() routine after downloading new firmware.
  */
 int __usb_reset_device(struct usb_device *udev)
@@ -2020,13 +2036,23 @@ int __usb_reset_device(struct usb_device *udev)
 	struct usb_device *parent = udev->parent;
 	struct usb_device_descriptor descriptor = udev->descriptor;
 	int i, ret, port = -1;
+	struct usb_hub *hub;
 
+	if (udev->state == USB_STATE_NOTATTACHED ||
+			udev->state == USB_STATE_SUSPENDED) {
+		dev_dbg(&udev->dev, "device reset not allowed in state %d\n",
+				udev->state);
+		return -EINVAL;
+	}
+
+	/* FIXME: This should be legal for regular hubs.  Root hubs may
+	 * have special requirements. */
 	if (udev->maxchild) {
 		/* this requires hub- or hcd-specific logic;
 		 * see hub_reset() and OHCI hc_restart()
 		 */
 		dev_dbg(&udev->dev, "%s for hub!\n", __FUNCTION__);
-		return -EINVAL;
+		return -EISDIR;
 	}
 
 	for (i = 0; i < parent->maxchild; i++)
@@ -2035,8 +2061,11 @@ int __usb_reset_device(struct usb_device *udev)
 			break;
 		}
 
-	if (port < 0)
+	if (port < 0) {
+		/* If this ever happens, it's very bad */
+		dev_err(&udev->dev, "Can't locate device's port!\n");
 		return -ENOENT;
+	}
 
 	ret = hub_port_init(parent, udev, port);
 	if (ret < 0)
@@ -2088,8 +2117,18 @@ int __usb_reset_device(struct usb_device *udev)
 	return 0;
  
 re_enumerate:
-	/* FIXME make some task re-enumerate; don't just mark unusable */
 	hub_port_disable(parent, port);
+
+	hub = usb_get_intfdata(parent->actconfig->interface[0]);
+	set_bit(port, hub->change_bits);
+
+	spin_lock_irq(&hub_event_lock);
+	if (list_empty(&hub->event_list)) {
+		list_add_tail(&hub->event_list, &hub_event_list);
+		wake_up(&khubd_wait);
+	}
+	spin_unlock_irq(&hub_event_lock);
+
 	return -ENODEV;
 }
 EXPORT_SYMBOL(__usb_reset_device);

drivers/usb/core/hub.h

@@ -204,6 +204,8 @@ struct usb_hub {
 
 	struct list_head	event_list;	/* hubs w/data or errs ready */
 	unsigned long		event_bits[1];	/* status change bitmask */
+	unsigned long		change_bits[1];	/* ports with logical connect
+							status change */
 #if USB_MAXCHILDREN > 31 /* 8*sizeof(unsigned long) - 1 */
 #error event_bits[] is too short!
 #endif

drivers/usb/gadget/dummy_hcd.c

@@ -146,8 +146,6 @@ struct dummy {
 	u8				fifo_buf [FIFO_SIZE];
 	u16				devstatus;
 
-	struct hcd_dev			*hdev;
-
 	/*
 	 * MASTER/HOST side support
 	 */
@@ -159,6 +157,8 @@ struct dummy {
 	struct completion		released;
 	unsigned			resuming:1;
 	unsigned long			re_timeout;
+
+	struct usb_device		*udev;
 };
 
 static struct dummy	*the_controller;
@@ -739,11 +739,9 @@ stop_activity (struct dummy *dum, struct usb_gadget_driver *driver)
 	struct dummy_ep	*ep;
 
 	/* prevent any more requests */
-	dum->hdev = 0;
 	dum->address = 0;
 
-	/* this might not succeed ... */
-	del_timer (&dum->timer);
+	/* The timer is left running so that outstanding URBs can fail */
 
 	/* nuke any pending requests first, so driver i/o is quiesced */
 	list_for_each_entry (ep, &dum->gadget.ep_list, ep.ep_list)
@@ -784,7 +782,6 @@ usb_gadget_unregister_driver (struct usb_gadget_driver *driver)
 
 	driver_unregister (&driver->driver);
 
-	del_timer_sync (&dum->timer);
 	return 0;
 }
 EXPORT_SYMBOL (usb_gadget_unregister_driver);
@@ -825,7 +822,12 @@ static int dummy_urb_enqueue (
 	dum = container_of (hcd, struct dummy, hcd);
 	spin_lock_irqsave (&dum->lock, flags);
 
-	dum->hdev = urb->dev->hcpriv;
+	if (!dum->udev) {
+		dum->udev = urb->dev;
+		usb_get_dev (dum->udev);
+	} else if (unlikely (dum->udev != urb->dev))
+		dev_err (hardware, "usb_device address has changed!\n");
+
 	urb->hcpriv = dum;
 	if (usb_pipetype (urb->pipe) == PIPE_CONTROL)
 		urb->error_count = 1;		/* mark as a new urb */
@@ -1032,17 +1034,12 @@ static struct dummy_ep *find_endpoint (struct dummy *dum, u8 address)
 static void dummy_timer (unsigned long _dum)
 {
 	struct dummy		*dum = (struct dummy *) _dum;
-	struct hcd_dev		*hdev = dum->hdev;
+	struct hcd_dev		*hdev;
 	struct list_head	*entry, *tmp;
 	unsigned long		flags;
 	int			limit, total;
 	int			i;
 
-	if (!hdev) {
-		dev_err (hardware, "timer fired with device gone?\n");
-		return;
-	}
-
 	/* simplistic model for one frame's bandwidth */
 	switch (dum->gadget.speed) {
 	case USB_SPEED_LOW:
@@ -1063,6 +1060,14 @@ static void dummy_timer (unsigned long _dum)
 
 	/* look at each urb queued by the host side driver */
 	spin_lock_irqsave (&dum->lock, flags);
+
+	if (!dum->udev) {
+		dev_err (hardware, "timer fired with no URBs pending?\n");
+		spin_unlock_irqrestore (&dum->lock, flags);
+		return;
+	}
+	hdev = dum->udev->hcpriv;
+
 	for (i = 0; i < DUMMY_ENDPOINTS; i++) {
 		if (!ep_name [i])
 			break;
@@ -1334,7 +1339,11 @@ static void dummy_timer (unsigned long _dum)
 
 	/* want a 1 msec delay here */
 	if (!list_empty (&hdev->urb_list))
-		mod_timer (&dum->timer, jiffies + 1);
+		mod_timer (&dum->timer, jiffies + msecs_to_jiffies(1));
+	else {
+		usb_put_dev (dum->udev);
+		dum->udev = NULL;
+	}
 
 	spin_unlock_irqrestore (&dum->lock, flags);
 }
@@ -1571,10 +1580,12 @@ show_urbs (struct device *dev, char *buf)
 	struct urb		*urb;
 	size_t			size = 0;
 	unsigned long		flags;
+	struct hcd_dev		*hdev;
 
 	spin_lock_irqsave (&dum->lock, flags);
-	if (dum->hdev) {
-		list_for_each_entry (urb, &dum->hdev->urb_list, urb_list) {
+	if (dum->udev) {
+		hdev = dum->udev->hcpriv;
+		list_for_each_entry (urb, &hdev->urb_list, urb_list) {
 			size_t		temp;
 
 			temp = show_urb (buf, PAGE_SIZE - size, urb);

drivers/usb/gadget/ether.c

@@ -234,7 +234,7 @@ MODULE_PARM_DESC(host_addr, "Host Ethernet Address");
 /* For CDC-incapable hardware, choose the simple cdc subset.
  * Anything that talks bulk (without notable bugs) can do this.
  */
-#ifdef CONFIG_USB_GADGET_PXA
+#ifdef CONFIG_USB_GADGET_PXA2XX
 #define	DEV_CONFIG_SUBSET
 #endif
 
@@ -1597,6 +1597,8 @@ eth_setup (struct usb_gadget *gadget, const struct usb_ctrlrequest *ctrl)
 	/* respond with data transfer before status phase? */
 	if (value >= 0) {
 		req->length = value;
+		req->zero = value < ctrl->wLength
+				&& (value % gadget->ep0->maxpacket) == 0;
 		value = usb_ep_queue (gadget->ep0, req, GFP_ATOMIC);
 		if (value < 0) {
 			DEBUG (dev, "ep_queue --> %d\n", value);
@@ -2373,6 +2375,7 @@ eth_bind (struct usb_gadget *gadget)
 	EP_OUT_NAME = ep->name;
 	ep->driver_data = ep;	/* claim */
 
+#if defined(DEV_CONFIG_CDC) || defined(CONFIG_USB_ETH_RNDIS)
 	/* CDC Ethernet control interface doesn't require a status endpoint.
 	 * Since some hosts expect one, try to allocate one anyway.
 	 */
@@ -2386,13 +2389,12 @@ eth_bind (struct usb_gadget *gadget)
 				"can't run RNDIS on %s\n",
 				gadget->name);
 			return -ENODEV;
-#ifdef	DEV_CONFIG_CDC
 		} else if (cdc) {
 			control_intf.bNumEndpoints = 0;
 			/* FIXME remove endpoint from descriptor list */
-#endif
 		}
 	}
+#endif
 
 	/* one config:  cdc, else minimal subset */
 	if (!cdc) {
@@ -2446,7 +2448,7 @@ eth_bind (struct usb_gadget *gadget)
 
 	/* Module params for these addresses should come from ID proms.
 	 * The host side address is used with CDC and RNDIS, and commonly
-	 * end ups in a persistent config database.
+	 * ends up in a persistent config database.
 	 */
 	get_ether_addr(dev_addr, net->dev_addr);
 	if (cdc || rndis) {

drivers/usb/gadget/file_storage.c

@@ -1465,6 +1465,8 @@ static int fsg_setup(struct usb_gadget *gadget,
 	/* Respond with data/status or defer until later? */
 	if (rc >= 0 && rc != DELAYED_STATUS) {
 		fsg->ep0req->length = rc;
+		fsg->ep0req->zero = rc < ctrl->wLength
+				&& (rc % gadget->ep0->maxpacket) == 0;
 		fsg->ep0req_name = (ctrl->bRequestType & USB_DIR_IN ?
 				"ep0-in" : "ep0-out");
 		rc = ep0_queue(fsg);

drivers/usb/gadget/inode.c

@@ -20,7 +20,7 @@
  */
 
 
-#define	DEBUG 1			/* data to help fault diagnosis */
+// #define	DEBUG 			/* data to help fault diagnosis */
 // #define	VERBOSE		/* extra debug messages (success too) */
 
 #include <linux/init.h>
@@ -44,7 +44,8 @@
  * The gadgetfs API maps each endpoint to a file descriptor so that you
  * can use standard synchronous read/write calls for I/O.  There's some
  * O_NONBLOCK and O_ASYNC/FASYNC style i/o support.  Example usermode
- * drivers show how this works in practice.
+ * drivers show how this works in practice.  You can also use AIO to
+ * eliminate I/O gaps between requests, to help when streaming data.
  *
  * Key parts that must be USB-specific are protocols defining how the
  * read/write operations relate to the hardware state machines.  There
@@ -70,7 +71,7 @@
  */
 
 #define	DRIVER_DESC	"USB Gadget filesystem"
-#define	DRIVER_VERSION	"20 Aug 2003"
+#define	DRIVER_VERSION	"18 Nov 2003"
 
 static const char driver_desc [] = DRIVER_DESC;
 static const char shortname [] = "gadgetfs";
@@ -539,6 +540,177 @@ static int ep_ioctl (struct inode *inode, struct file *fd,
 	return status;
 }
 
+/*----------------------------------------------------------------------*/
+
+/* ASYNCHRONOUS ENDPOINT I/O OPERATIONS (bulk/intr/iso) */
+
+struct kiocb_priv {
+	struct usb_request	*req;
+	struct ep_data		*epdata;
+	void			*buf;
+	char __user		*ubuf;
+	unsigned		actual;
+};
+
+static int ep_aio_cancel(struct kiocb *iocb, struct io_event *e)
+{
+	struct kiocb_priv	*priv = (void *) &iocb->private;
+	struct ep_data		*epdata;
+	int			value;
+
+	local_irq_disable();
+	epdata = priv->epdata;
+	// spin_lock(&epdata->dev->lock);
+	kiocbSetCancelled(iocb);
+	if (likely(epdata && epdata->ep && priv->req))
+		value = usb_ep_dequeue (epdata->ep, priv->req);
+	else
+		value = -EINVAL;
+	// spin_unlock(&epdata->dev->lock);
+	local_irq_enable();
+
+	aio_put_req(iocb);
+	return value;
+}
+
+static long ep_aio_read_retry(struct kiocb *iocb)
+{
+	struct kiocb_priv	*priv = (void *) &iocb->private;
+	int			status = priv->actual;
+
+	/* we "retry" to get the right mm context for this: */
+	status = copy_to_user(priv->ubuf, priv->buf, priv->actual);
+	if (unlikely(0 != status))
+		status = -EFAULT;
+	else
+		status = priv->actual;
+	kfree(priv->buf);
+	aio_put_req(iocb);
+	return status;
+}
+
+static void ep_aio_complete(struct usb_ep *ep, struct usb_request *req)
+{
+	struct kiocb		*iocb = req->context;
+	struct kiocb_priv	*priv = (void *) &iocb->private;
+	struct ep_data		*epdata = priv->epdata;
+
+	/* lock against disconnect (and ideally, cancel) */
+	spin_lock(&epdata->dev->lock);
+	priv->req = 0;
+	priv->epdata = 0;
+	if (NULL == iocb->ki_retry
+			|| unlikely(0 == req->actual)
+			|| unlikely(kiocbIsCancelled(iocb))) {
+		kfree(req->buf);
+		/* aio_complete() reports bytes-transferred _and_ faults */
+		if (unlikely(kiocbIsCancelled(iocb)))
+			aio_put_req(iocb);
+		else
+			aio_complete(iocb,
+				req->actual ? req->actual : req->status,
+				req->status);
+	} else {
+		/* retry() won't report both; so we hide some faults */
+		if (unlikely(0 != req->status))
+			DBG(epdata->dev, "%s fault %d len %d\n",
+				ep->name, req->status, req->actual);
+
+		priv->buf = req->buf;
+		priv->actual = req->actual;
+		kick_iocb(iocb);
+	}
+	spin_unlock(&epdata->dev->lock);
+
+	usb_ep_free_request(ep, req);
+	put_ep(epdata);
+}
+
+static ssize_t
+ep_aio_rwtail(struct kiocb *iocb, char *buf, size_t len, struct ep_data *epdata)
+{
+	struct kiocb_priv	*priv = (void *) &iocb->private;
+	struct usb_request	*req;
+	ssize_t			value;
+
+	value = get_ready_ep(iocb->ki_filp->f_flags, epdata);
+	if (unlikely(value < 0)) {
+		kfree(buf);
+		return value;
+	}
+
+	iocb->ki_cancel = ep_aio_cancel;
+	get_ep(epdata);
+	priv->epdata = epdata;
+	priv->actual = 0;
+
+	/* each kiocb is coupled to one usb_request, but we can't
+	 * allocate or submit those if the host disconnected.
+	 */
+	spin_lock_irq(&epdata->dev->lock);
+	if (likely(epdata->ep)) {
+		req = usb_ep_alloc_request(epdata->ep, GFP_ATOMIC);
+		if (likely(req)) {
+			priv->req = req;
+			req->buf = buf;
+			req->length = len;
+			req->complete = ep_aio_complete;
+			req->context = iocb;
+			value = usb_ep_queue(epdata->ep, req, GFP_ATOMIC);
+			if (unlikely(0 != value))
+				usb_ep_free_request(epdata->ep, req);
+		} else
+			value = -EAGAIN;
+	} else
+		value = -ENODEV;
+	spin_unlock_irq(&epdata->dev->lock);
+
+	up(&epdata->lock);
+
+	if (unlikely(value))
+		put_ep(epdata);
+	else
+		value = -EIOCBQUEUED;
+	return value;
+}
+
+static ssize_t
+ep_aio_read(struct kiocb *iocb, char __user *ubuf, size_t len, loff_t o)
+{
+	struct kiocb_priv	*priv = (void *) &iocb->private;
+	struct ep_data		*epdata = iocb->ki_filp->private_data;
+	char			*buf;
+
+	if (unlikely(epdata->desc.bEndpointAddress & USB_DIR_IN))
+		return -EINVAL;
+	buf = kmalloc(len, GFP_KERNEL);
+	if (unlikely(!buf))
+		return -ENOMEM;
+	iocb->ki_retry = ep_aio_read_retry;
+	priv->ubuf = ubuf;
+	return ep_aio_rwtail(iocb, buf, len, epdata);
+}
+
+static ssize_t
+ep_aio_write(struct kiocb *iocb, const char __user *ubuf, size_t len, loff_t o)
+{
+	struct ep_data		*epdata = iocb->ki_filp->private_data;
+	char			*buf;
+
+	if (unlikely(!(epdata->desc.bEndpointAddress & USB_DIR_IN)))
+		return -EINVAL;
+	buf = kmalloc(len, GFP_KERNEL);
+	if (unlikely(!buf))
+		return -ENOMEM;
+	if (unlikely(copy_from_user(buf, ubuf, len) != 0)) {
+		kfree(buf);
+		return -EFAULT;
+	}
+	return ep_aio_rwtail(iocb, buf, len, epdata);
+}
+
+/*----------------------------------------------------------------------*/
+
 /* used after endpoint configuration */
 static struct file_operations ep_io_operations = {
 	.owner =	THIS_MODULE,
@@ -547,8 +719,8 @@ static struct file_operations ep_io_operations = {
 	.ioctl =	ep_ioctl,
 	.release =	ep_release,
 
-	// .aio_read =	ep_aio_read,
-	// .aio_write =	ep_aio_write,
+	.aio_read =	ep_aio_read,
+	.aio_write =	ep_aio_write,
 };
 
 /* ENDPOINT INITIALIZATION
@@ -1320,6 +1492,8 @@ gadgetfs_setup (struct usb_gadget *gadget, const struct usb_ctrlrequest *ctrl)
 	/* proceed with data transfer and status phases? */
 	if (value >= 0 && dev->state != STATE_SETUP) {
 		req->length = value;
+		req->zero = value < ctrl->wLength
+				&& (value % gadget->ep0->maxpacket) == 0;
 		value = usb_ep_queue (gadget->ep0, req, GFP_ATOMIC);
 		if (value < 0) {
 			DBG (dev, "ep_queue --> %d\n", value);

drivers/usb/gadget/serial.c

@@ -1573,6 +1573,8 @@ static int gs_setup(struct usb_gadget *gadget, const struct usb_ctrlrequest *ctr
 	/* respond with data transfer before status phase? */
 	if (ret >= 0) {
 		req->length = ret;
+		req->zero = ret < ctrl->wLength
+				&& (ret % gadget->ep0->maxpacket) == 0;
 		ret = usb_ep_queue(gadget->ep0, req, GFP_ATOMIC);
 		if (ret < 0) {
 			printk(KERN_ERR

drivers/usb/gadget/zero.c

@@ -1037,6 +1037,8 @@ zero_setup (struct usb_gadget *gadget, const struct usb_ctrlrequest *ctrl)
 	/* respond with data transfer before status phase? */
 	if (value >= 0) {
 		req->length = value;
+		req->zero = value < ctrl->wLength
+				&& (value % gadget->ep0->maxpacket) == 0;
 		value = usb_ep_queue (gadget->ep0, req, GFP_ATOMIC);
 		if (value < 0) {
 			DBG (dev, "ep_queue --> %d\n", value);

drivers/usb/host/ehci-hcd.c

@@ -425,7 +425,6 @@ static int ehci_start (struct usb_hcd *hcd)
 		ehci_mem_cleanup (ehci);
 		return retval;
 	}
-	writel (INTR_MASK, &ehci->regs->intr_enable);
 	writel (ehci->periodic_dma, &ehci->regs->frame_list);
 
 #ifdef	CONFIG_PCI
@@ -531,7 +530,8 @@ static int ehci_start (struct usb_hcd *hcd)
 	/*
 	 * Start, enabling full USB 2.0 functionality ... usb 1.1 devices
 	 * are explicitly handed to companion controller(s), so no TT is
-	 * involved with the root hub.
+	 * involved with the root hub.  (Except where one is integrated,
+	 * and there's no companion controller unless maybe for USB OTG.)
 	 */
 	ehci->reboot_notifier.notifier_call = ehci_reboot;
 	register_reboot_notifier (&ehci->reboot_notifier);
@@ -563,6 +563,8 @@ static int ehci_start (struct usb_hcd *hcd)
 		goto done2;
 	}
 
+	writel (INTR_MASK, &ehci->regs->intr_enable); /* Turn On Interrupts */
+
 	create_debug_files (ehci);
 
 	return 0;
@@ -573,6 +575,7 @@ static int ehci_start (struct usb_hcd *hcd)
 static void ehci_stop (struct usb_hcd *hcd)
 {
 	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
+	u8			rh_ports, port;
 
 	ehci_dbg (ehci, "stop\n");
 
@@ -584,7 +587,16 @@ static void ehci_stop (struct usb_hcd *hcd)
 		return;
 	}
 	del_timer_sync (&ehci->watchdog);
+
+	/* Turn off port power on all root hub ports. */
+	rh_ports = HCS_N_PORTS (ehci->hcs_params);
+	for (port = 1; port <= rh_ports; port++) {
+		ehci_hub_control(hcd, ClearPortFeature, USB_PORT_FEAT_POWER,
+			port, NULL, 0);
+	}
+
 	ehci_reset (ehci);
+	writel (0, &ehci->regs->intr_enable);
 
 	/* let companion controllers work when we aren't */
 	writel (0, &ehci->regs->configured_flag);
@@ -704,12 +716,6 @@ static irqreturn_t ehci_irq (struct usb_hcd *hcd, struct pt_regs *regs)
 
 	status = readl (&ehci->regs->status);
 
-	/* shared irq */
-	if (status == 0) {
-		spin_unlock (&ehci->lock);
-		return IRQ_NONE;
-	}
-
 	/* e.g. cardbus physical eject */
 	if (status == ~(u32) 0) {
 		ehci_dbg (ehci, "device removed\n");
@@ -717,8 +723,10 @@ static irqreturn_t ehci_irq (struct usb_hcd *hcd, struct pt_regs *regs)
 	}
 
 	status &= INTR_MASK;
-	if (!status)			/* irq sharing? */
-		goto done;
+	if (!status) {			/* irq sharing? */
+		spin_unlock(&ehci->lock);
+		return IRQ_NONE;
+	}
 
 	/* clear (just) interrupts */
 	writel (status, &ehci->regs->status);
@@ -789,7 +797,6 @@ static irqreturn_t ehci_irq (struct usb_hcd *hcd, struct pt_regs *regs)
 
 	if (bh)
 		ehci_work (ehci, regs);
-done:
 	spin_unlock (&ehci->lock);
 	return IRQ_HANDLED;
 }

drivers/usb/host/uhci-debug.c

@@ -248,7 +248,7 @@ static int uhci_show_sc(int port, unsigned short status, char *buf, int len)
 static int uhci_show_status(struct uhci_hcd *uhci, char *buf, int len)
 {
 	char *out = buf;
-	unsigned int io_addr = uhci->io_addr;
+	unsigned long io_addr = uhci->io_addr;
 	unsigned short usbcmd, usbstat, usbint, usbfrnum;
 	unsigned int flbaseadd;
 	unsigned char sof;

drivers/usb/host/uhci-hcd.c

@@ -1762,7 +1762,7 @@ static void uhci_remove_pending_urbps(struct uhci_hcd *uhci)
 static irqreturn_t uhci_irq(struct usb_hcd *hcd, struct pt_regs *regs)
 {
 	struct uhci_hcd *uhci = hcd_to_uhci(hcd);
-	unsigned int io_addr = uhci->io_addr;
+	unsigned long io_addr = uhci->io_addr;
 	unsigned short status;
 	struct list_head *tmp, *head;
 	unsigned int age;
@@ -1835,7 +1835,7 @@ static irqreturn_t uhci_irq(struct usb_hcd *hcd, struct pt_regs *regs)
 
 static void reset_hc(struct uhci_hcd *uhci)
 {
-	unsigned int io_addr = uhci->io_addr;
+	unsigned long io_addr = uhci->io_addr;
 
 	/* Turn off PIRQ, SMI, and all interrupts.  This also turns off
 	 * the BIOS's USB Legacy Support.
@@ -1856,7 +1856,7 @@ static void reset_hc(struct uhci_hcd *uhci)
 
 static void suspend_hc(struct uhci_hcd *uhci)
 {
-	unsigned int io_addr = uhci->io_addr;
+	unsigned long io_addr = uhci->io_addr;
 
 	dev_dbg(uhci_dev(uhci), "%s\n", __FUNCTION__);
 	uhci->state = UHCI_SUSPENDED;
@@ -1866,7 +1866,7 @@ static void suspend_hc(struct uhci_hcd *uhci)
 
 static void wakeup_hc(struct uhci_hcd *uhci)
 {
-	unsigned int io_addr = uhci->io_addr;
+	unsigned long io_addr = uhci->io_addr;
 
 	switch (uhci->state) {
 		case UHCI_SUSPENDED:		/* Start the resume */
@@ -1906,7 +1906,7 @@ static void wakeup_hc(struct uhci_hcd *uhci)
 
 static int ports_active(struct uhci_hcd *uhci)
 {
-	unsigned int io_addr = uhci->io_addr;
+	unsigned long io_addr = uhci->io_addr;
 	int connection = 0;
 	int i;
 
@@ -1918,7 +1918,7 @@ static int ports_active(struct uhci_hcd *uhci)
 
 static int suspend_allowed(struct uhci_hcd *uhci)
 {
-	unsigned int io_addr = uhci->io_addr;
+	unsigned long io_addr = uhci->io_addr;
 	int i;
 
 	if (to_pci_dev(uhci_dev(uhci))->vendor != PCI_VENDOR_ID_INTEL)
@@ -1983,7 +1983,7 @@ static void hc_state_transitions(struct uhci_hcd *uhci)
 
 static void start_hc(struct uhci_hcd *uhci)
 {
-	unsigned int io_addr = uhci->io_addr;
+	unsigned long io_addr = uhci->io_addr;
 	int timeout = 1000;
 
 	/*
@@ -2261,6 +2261,11 @@ static int uhci_start(struct usb_hcd *hcd)
 		uhci->fl->frame[i] = cpu_to_le32(uhci->skelqh[irq]->dma_handle);
 	}
 
+	/*
+	 * Some architectures require a full mb() to enforce completion of
+	 * the memory writes above before the I/O transfers in start_hc().
+	 */
+	mb();
 	start_hc(uhci);
 
 	init_stall_timer(hcd);

drivers/usb/host/uhci-hub.c

@@ -36,7 +36,7 @@ static __u8 root_hub_hub_des[] =
 static int uhci_hub_status_data(struct usb_hcd *hcd, char *buf)
 {
 	struct uhci_hcd *uhci = hcd_to_uhci(hcd);
-	unsigned int io_addr = uhci->io_addr;
+	unsigned long io_addr = uhci->io_addr;
 	int i;
 
 	*buf = 0;
@@ -69,7 +69,7 @@ static int uhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
 {
 	struct uhci_hcd *uhci = hcd_to_uhci(hcd);
 	int status, retval = 0, len = 0;
-	unsigned int port_addr = uhci->io_addr + USBPORTSC1 + 2 * (wIndex-1);
+	unsigned long port_addr = uhci->io_addr + USBPORTSC1 + 2 * (wIndex-1);
 	__u16 wPortChange, wPortStatus;
 
 	switch (typeReq) {

drivers/usb/input/hid-tmff.c

@@ -110,7 +110,7 @@ int hid_tmff_init(struct hid_device *hid)
 {
 	struct tmff_device *private;
 	struct list_head *pos;
-	struct hid_input *hidinput = list_entry(&hid->inputs, struct hid_input, list);
+	struct hid_input *hidinput = list_entry(hid->inputs.next, struct hid_input, list);
 
 	private = kmalloc(sizeof(struct tmff_device), GFP_KERNEL);
 	if (!private)

drivers/usb/media/Kconfig

@@ -108,7 +108,7 @@ config USB_OV511
 
 config USB_PWC
 	tristate "USB Philips Cameras"
-	depends on USB && VIDEO_DEV && CONFIG_BROKEN
+	depends on USB && VIDEO_DEV
 	---help---
 	  Say Y or M here if you want to use one of these Philips & OEM
           webcams:

drivers/usb/media/konicawc.c

@@ -324,7 +324,7 @@ static void resubmit_urb(struct uvd *uvd, struct urb *urb)
         }
         urb->dev = uvd->dev;
         urb->status = 0;
-        ret = usb_submit_urb(urb, GFP_KERNEL);
+	ret = usb_submit_urb(urb, GFP_ATOMIC);
 	DEBUG(3, "submitting urb of length %d", urb->transfer_buffer_length);
         if(ret)
                 err("usb_submit_urb error (%d)", ret);

drivers/usb/media/pwc-ioctl.h

 #ifndef PWC_IOCTL_H
 #define PWC_IOCTL_H
 
-/* (C) 2001-2003 Nemosoft Unv.    webcam@smcc.demon.nl
+/* (C) 2001-2004 Nemosoft Unv.    webcam@smcc.demon.nl
 
    This program is free software; you can redistribute it and/or modify
    it under the terms of the GNU General Public License as published by
@@ -18,13 +18,18 @@
    Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 */
 
-/*         This is pwc-ioctl.h belonging to PWC 8.10                        */
+/* This is pwc-ioctl.h belonging to PWC 8.12.1
+   It contains structures and defines to communicate from user space
+   directly to the driver.
+ */
 
 /*
    Changes
    2001/08/03  Alvarado   Added ioctl constants to access methods for
                           changing white balance and red/blue gains
    2002/12/15  G. H. Fernandez-Toribio   VIDIOCGREALSIZE
+   2003/12/13  Nemosft Unv. Some modifications to make interfacing to
+               PWCX easier
  */
 
 /* These are private ioctl() commands, specific for the Philips webcams.
@@ -40,6 +45,14 @@
  */
 
 
+ /* Enumeration of image sizes */
+#define PSZ_SQCIF	0x00
+#define PSZ_QSIF	0x01
+#define PSZ_QCIF	0x02
+#define PSZ_SIF		0x03
+#define PSZ_CIF		0x04
+#define PSZ_VGA		0x05
+#define PSZ_MAX		6
 
 
 /* The frame rate is encoded in the video_window.flags parameter using
@@ -55,13 +68,25 @@
 #define PWC_FPS_SNAPSHOT	0x00400000
 
 
+/* structure for transfering x & y coordinates */
+struct pwc_coord
+{
+	int x, y;		/* guess what */
+	int size;		/* size, or offset */
+};
 
+
+/* Used with VIDIOCPWCPROBE */
 struct pwc_probe
 {
 	char name[32];
 	int type;
 };
 
+struct pwc_serial
+{
+	char serial[30];	/* String with serial number. Contains terminating 0 */
+};
 	
 /* pwc_whitebalance.mode values */
 #define PWC_WB_INDOOR		0
@@ -78,7 +103,6 @@ struct pwc_probe
    otherwise undefined.
    'read_red' and 'read_blue' are read-only.
 */   
-   
 struct pwc_whitebalance
 {
 	int mode;
@@ -117,7 +141,7 @@ struct pwc_imagesize
 #define PWC_MPT_TILT		0x02
 #define PWC_MPT_TIMEOUT		0x04 /* for status */
 
-/* Set angles; when absolute = 1, the angle is absolute and the 
+/* Set angles; when absolute != 0, the angle is absolute and the 
    driver calculates the relative offset for you. This can only
    be used with VIDIOCPWCSANGLE; VIDIOCPWCGANGLE always returns
    absolute angles.
@@ -127,18 +151,14 @@ struct pwc_mpt_angles
 	int absolute;		/* write-only */
 	int pan;		/* degrees * 100 */
 	int tilt;		/* degress * 100 */
-	int zoom;		/* N/A, set to -1 */
 };
 
 /* Range of angles of the camera, both horizontally and vertically.
-   The zoom is not used, maybe in the future...
-
  */
 struct pwc_mpt_range
 {
 	int pan_min, pan_max;		/* degrees * 100 */
 	int tilt_min, tilt_max;
-	int zoom_min, zoom_max;		/* -1, -1 */
 };
 
 struct pwc_mpt_status
@@ -149,6 +169,30 @@ struct pwc_mpt_status
 };
 
 
+/* This is used for out-of-kernel decompression. With it, you can get
+   all the necessary information to initialize and use the decompressor
+   routines in standalone applications.
+ */   
+struct pwc_video_command
+{
+	int type;		/* camera type (645, 675, 730, etc.) */
+	int release;		/* release number */
+
+        int size;		/* one of PSZ_* */
+        int alternate;
+	int command_len;	/* length of USB video command */
+	unsigned char command_buf[13];	/* Actual USB video command */
+	int bandlength;		/* >0 = compressed */
+	int frame_size;		/* Size of one (un)compressed frame */
+};
+
+/* Flags for PWCX subroutines. Not all modules honour all flags. */
+#define PWCX_FLAG_PLANAR	0x0001
+#define PWCX_FLAG_BAYER		0x0008
+
+
+/* IOCTL definitions */
+
  /* Restore user settings */
 #define VIDIOCPWCRUSER		_IO('v', 192)
  /* Save user settings */
@@ -169,6 +213,9 @@ struct pwc_mpt_status
 #define VIDIOCPWCGCQUAL		_IOR('v', 195, int)
 
 
+/* Retrieve serial number of camera */
+#define VIDIOCPWCGSERIAL	_IOR('v', 198, struct pwc_serial)
+
  /* This is a probe function; since so many devices are supported, it
     becomes difficult to include all the names in programs that want to
     check for the enhanced Philips stuff. So in stead, try this PROBE;
@@ -226,4 +273,7 @@ struct pwc_mpt_status
 #define VIDIOCPWCMPTGANGLE	_IOR('v', 212, struct pwc_mpt_angles)
 #define VIDIOCPWCMPTSTATUS	_IOR('v', 213, struct pwc_mpt_status)
 
+ /* Get the USB set-video command; needed for initializing libpwcx */
+#define VIDIOCPWCGVIDCMD	_IOR('v', 215, struct pwc_video_command)
+
 #endif

drivers/usb/media/pwc-misc.c

@@ -36,9 +36,28 @@ int pwc_decode_size(struct pwc_device *pdev, int width, int height)
 {
 	int i, find;
 
-	/* Make sure we don't go beyond our max size */
+	/* Make sure we don't go beyond our max size.
+           NB: we have different limits for RAW and normal modes. In case
+           you don't have the decompressor loaded or use RAW mode, 
+           the maximum viewable size is smaller.
+        */
+	if (pdev->vpalette == VIDEO_PALETTE_RAW)
+	{
+		if (width > pdev->abs_max.x || height > pdev->abs_max.y)
+		{
+			Debug("VIDEO_PALETTE_RAW: going beyond abs_max.\n");
+                	return -1;
+                }
+	}
+	else
+	{
 		if (width > pdev->view_max.x || height > pdev->view_max.y)
+		{
+			Debug("VIDEO_PALETTE_ not RAW: going beyond view_max.\n");
 			return -1;
+		}
+	}
+
 	/* Find the largest size supported by the camera that fits into the
 	   requested size.
 	 */
@@ -62,6 +81,8 @@ void pwc_construct(struct pwc_device *pdev)
 		pdev->view_min.y =  96;
 		pdev->view_max.x = 352;
 		pdev->view_max.y = 288;
+                pdev->abs_max.x  = 352;
+                pdev->abs_max.y  = 288;
 		pdev->image_mask = 1 << PSZ_SQCIF | 1 << PSZ_QCIF | 1 << PSZ_CIF;
 		pdev->vcinterface = 2;
 		pdev->vendpoint = 4;
@@ -77,13 +98,14 @@ void pwc_construct(struct pwc_device *pdev)
 		if (pdev->decompressor != NULL) {
 			pdev->view_max.x = 640;
 			pdev->view_max.y = 480;
-			pdev->image_mask = 1 << PSZ_SQCIF | 1 << PSZ_QSIF | 1 << PSZ_QCIF | 1 << PSZ_SIF | 1 << PSZ_CIF | 1 << PSZ_VGA;
 		}
 		else {
 			pdev->view_max.x = 352;
 			pdev->view_max.y = 288;
-			pdev->image_mask = 1 << PSZ_SQCIF | 1 << PSZ_QSIF | 1 << PSZ_QCIF | 1 << PSZ_SIF | 1 << PSZ_CIF;
 		}
+		pdev->image_mask = 1 << PSZ_SQCIF | 1 << PSZ_QSIF | 1 << PSZ_QCIF | 1 << PSZ_SIF | 1 << PSZ_CIF | 1 << PSZ_VGA;
+                pdev->abs_max.x = 640;
+                pdev->abs_max.y = 480;
 		pdev->vcinterface = 3;
 		pdev->vendpoint = 4;
 		pdev->frame_header_size = 0;
@@ -99,24 +121,26 @@ void pwc_construct(struct pwc_device *pdev)
 		if (pdev->decompressor != NULL) {
 			pdev->view_max.x = 640;
 			pdev->view_max.y = 480;
-			pdev->image_mask = 1 << PSZ_QSIF | 1 << PSZ_SIF | 1 << PSZ_VGA;
 		}
 		else {
-			/* Tell CIF, even though SIF really is the maximum, but some tools really need CIF */
+			/* We use CIF, not SIF since some tools really need CIF. So we cheat a bit. */
 			pdev->view_max.x = 352;
 			pdev->view_max.y = 288;
-			pdev->image_mask = 1 << PSZ_QSIF | 1 << PSZ_SIF;
 		}
+		pdev->image_mask = 1 << PSZ_QSIF | 1 << PSZ_SIF | 1 << PSZ_VGA;
+                pdev->abs_max.x = 640;
+                pdev->abs_max.y = 480;
 		pdev->vcinterface = 3;
 		pdev->vendpoint = 5;
 		pdev->frame_header_size = TOUCAM_HEADER_SIZE;
 		pdev->frame_trailer_size = TOUCAM_TRAILER_SIZE;
 		break;
 	}
+	pdev->vpalette = VIDEO_PALETTE_YUV420P; /* default */
 	pdev->view_min.size = pdev->view_min.x * pdev->view_min.y;
 	pdev->view_max.size = pdev->view_max.x * pdev->view_max.y;
-	/* length of image, in YUV format */
-	pdev->len_per_image = (pdev->view_max.size * 3) / 2;
+	/* length of image, in YUV format; always allocate enough memory. */
+	pdev->len_per_image = (pdev->abs_max.x * pdev->abs_max.y * 3) / 2;
 }
 
 

drivers/usb/media/pwc-uncompress.c

@@ -21,7 +21,9 @@
    themselves. It also has a decompressor wrapper function.
 */
 
+#include <asm/current.h>
 #include <asm/types.h>
+// #include <linux/sched.h>
 
 #include "pwc.h"
 #include "pwc-uncompress.h"
@@ -81,7 +83,6 @@ int pwc_decompress(struct pwc_device *pdev)
 	u16 *src;
 	u16 *dsty, *dstu, *dstv;
 
-	
 	if (pdev == NULL)
 		return -EFAULT;
 #if defined(__KERNEL__) && defined(PWC_MAGIC)
@@ -99,6 +100,14 @@ int pwc_decompress(struct pwc_device *pdev)
 		return -EFAULT;
 
 	yuv = fbuf->data + pdev->frame_header_size;  /* Skip header */
+
+	/* Raw format; that's easy... */
+	if (pdev->vpalette == VIDEO_PALETTE_RAW)
+	{
+		memcpy(image, yuv, pdev->frame_size);
+		return 0;
+	}
+
 	if (pdev->vbandlength == 0) {
 		/* Uncompressed mode. We copy the data into the output buffer,
 		   using the viewport size (which may be larger than the image
@@ -144,11 +153,17 @@ int pwc_decompress(struct pwc_device *pdev)
 		/* Compressed; the decompressor routines will write the data
 		   in planar format immediately.
 		 */
+		int flags;
+                
+                flags = PWCX_FLAG_PLANAR;
+                if (pdev->vsize == PSZ_VGA && pdev->vframes == 5 && pdev->vsnapshot)
+                	flags |= PWCX_FLAG_BAYER;
+
 		if (pdev->decompressor)
 			pdev->decompressor->decompress(
 				&pdev->image, &pdev->view, &pdev->offset,
 				yuv, image,
-				1,
+				flags,
 				pdev->decompress_data, pdev->vbandlength);
 		else
 			return -ENXIO; /* No such device or address: missing decompressor */

drivers/usb/media/pwc-uncompress.h

@@ -24,9 +24,15 @@
 #define PWC_UNCOMPRESS_H
 
 #include <linux/config.h>
+#include <linux/linkage.h>
 #include <linux/list.h>
 
-#include "pwc.h"
+#include "pwc-ioctl.h"
+
+/* from pwc-dec.h */
+#define PWCX_FLAG_PLANAR        0x0001
+/* */
+
 
 #ifdef __cplusplus
 extern "C" {
@@ -42,10 +48,11 @@ struct pwc_decompressor
 	int  type;		/* type of camera (645, 680, etc) */
 	int  table_size;	/* memory needed */
 
-	void (* init)(int release, void *buffer, void *table);	/* Initialization routine; should be called after each set_video_mode */
+	void (* init)(int type, int release, void *buffer, void *table);	/* Initialization routine; should be called after each set_video_mode */
 	void (* exit)(void);	/* Cleanup routine */
-	void (* decompress)(struct pwc_coord *image, struct pwc_coord *view, struct pwc_coord *offset,
-                            void *src, void *dst, int planar,
+	void (* decompress)(struct pwc_coord *image, struct pwc_coord *view,
+			    struct pwc_coord *offset,
+                            void *src, void *dst, int flags,
 	                    void *table, int bandlength);
 	void (* lock)(void);	/* make sure module cannot be unloaded */
 	void (* unlock)(void);	/* release lock on module */

drivers/usb/media/pwc.h

@@ -22,15 +22,15 @@
 
 #include <linux/config.h>
 #include <linux/module.h>
-#include <linux/smp_lock.h>
-#include <linux/spinlock.h>
 #include <linux/usb.h>
+#include <linux/spinlock.h>
 #include <linux/videodev.h>
 #include <linux/wait.h>
-
+#include <linux/smp_lock.h>
 #include <asm/semaphore.h>
 #include <asm/errno.h>
 
+#include "pwc-uncompress.h"
 #include "pwc-ioctl.h"
 
 /* Defines and structures for the Philips webcam */
@@ -65,9 +65,9 @@
 #define FEATURE_MOTOR_PANTILT		0x0001
 
 /* Version block */
-#define PWC_MAJOR	8
-#define PWC_MINOR	12
-#define PWC_VERSION 	"8.12"
+#define PWC_MAJOR	9
+#define PWC_MINOR	0
+#define PWC_VERSION 	"9.0.1"
 #define PWC_NAME 	"pwc"
 
 /* Turn certain features on/off */
@@ -90,12 +90,6 @@
 /* Absolute maximum number of buffers available for mmap() */
 #define MAX_IMAGES 		10
 
-struct pwc_coord
-{
-	int x, y;		/* guess what */
-	int size;		/* size, or offset */
-};
-
 /* The following structures were based on cpia.h. Why reinvent the wheel? :-) */
 struct pwc_iso_buf
 {
@@ -118,7 +112,7 @@ struct pwc_frame_buf
 
 struct pwc_device
 {
-   struct video_device vdev;
+   struct video_device *vdev;
 #ifdef PWC_MAGIC
    int magic;
 #endif
@@ -128,6 +122,7 @@ struct pwc_device
    int type;                    /* type of cam (645, 646, 675, 680, 690, 720, 730, 740, 750) */
    int release;			/* release number */
    int features;		/* feature bits */
+   char serial[30];		/* serial number (string) */
    int error_status;		/* set when something goes wrong with the cam (unplugged, USB errors) */
    int usb_init;		/* set when the cam has been initialized over USB */
 
@@ -137,6 +132,7 @@ struct pwc_device
    int vcinterface;		/* video control interface */
    int valternate;		/* alternate interface needed */
    int vframes, vsize;		/* frames-per-second & size (see PSZ_*) */
+   int vpalette;		/* palette: 420P, RAW or RGBBAYER */
    int vframe_count;		/* received frames */
    int vframes_dumped; 		/* counter for dumped frames */
    int vframes_error;		/* frames received in error */
@@ -149,6 +145,9 @@ struct pwc_device
    char vsync;			/* used by isoc handler */
    char vmirror;		/* for ToUCaM series */
    
+   int cmd_len;
+   unsigned char cmd_buf[13];
+
    /* The image acquisition requires 3 to 4 steps:
       1. data is gathered in short packets from the USB controller
       2. data is synchronized and packed into a frame buffer
@@ -169,8 +168,9 @@ struct pwc_device
    struct pwc_frame_buf *full_frames, *full_frames_tail;	/* all filled frames */
    struct pwc_frame_buf *fill_frame;	/* frame currently being filled */
    struct pwc_frame_buf *read_frame;	/* frame currently read by user process */
-   int frame_size;
    int frame_header_size, frame_trailer_size;
+   int frame_size;
+   int frame_total_size; /* including header & trailer */
    int drop_frames;
 #if PWC_DEBUG
    int sequence;			/* Debugging aid */
@@ -187,7 +187,8 @@ struct pwc_device
       a gray or black border. view_min <= image <= view <= view_max;
     */
    int image_mask;			/* bitmask of supported sizes */
-   struct pwc_coord view_min, view_max;	/* minimum and maximum sizes */
+   struct pwc_coord view_min, view_max;	/* minimum and maximum viewable sizes */
+   struct pwc_coord abs_max;            /* maximum supported size with compression */
    struct pwc_coord image, view;	/* image and viewport size */
    struct pwc_coord offset;		/* offset within the viewport */
 
@@ -213,16 +214,6 @@ struct pwc_device
 #endif
 };
 
-/* Enumeration of image sizes */
-#define PSZ_SQCIF	0x00
-#define PSZ_QSIF	0x01
-#define PSZ_QCIF	0x02
-#define PSZ_SIF		0x03
-#define PSZ_CIF		0x04
-#define PSZ_VGA		0x05
-#define PSZ_MAX		6
-
-
 
 #ifdef __cplusplus
 extern "C" {
@@ -259,7 +250,7 @@ extern int pwc_get_saturation(struct pwc_device *pdev);
 extern int pwc_set_saturation(struct pwc_device *pdev, int value);
 extern int pwc_set_leds(struct pwc_device *pdev, int on_value, int off_value);
 extern int pwc_get_leds(struct pwc_device *pdev, int *on_value, int *off_value);
-extern int pwc_get_cmos_sensor(struct pwc_device *pdev);
+extern int pwc_get_cmos_sensor(struct pwc_device *pdev, int *sensor);
 
 /* Power down or up the camera; not supported by all models */
 extern int pwc_camera_power(struct pwc_device *pdev, int power);

drivers/usb/net/kaweth.c

@@ -62,7 +62,7 @@
 #include <asm/semaphore.h>
 #include <asm/byteorder.h>
 
-#define DEBUG
+#undef DEBUG
 
 #ifdef DEBUG
 #define kaweth_dbg(format, arg...) printk(KERN_DEBUG __FILE__ ": " format "\n" ,##arg)
@@ -592,7 +592,7 @@ static void kaweth_usb_receive(struct urb *urb, struct pt_regs *regs)
 
 	struct sk_buff *skb;
 
-	if(unlikely(urb->status == -ECONNRESET || urb->status == -ECONNABORTED))
+	if(unlikely(urb->status == -ECONNRESET || urb->status == -ECONNABORTED || urb->status == -ESHUTDOWN))
 	/* we are killed - set a flag and wake the disconnect handler */
 	{
 		kaweth->end = 1;

drivers/usb/net/pegasus.c

@@ -1137,8 +1137,6 @@ static void pegasus_set_multicast(struct net_device *net)
 {
 	pegasus_t *pegasus = net->priv;
 
-	netif_stop_queue(net);
-
 	if (net->flags & IFF_PROMISC) {
 		pegasus->eth_regs[EthCtrl2] |= RX_PROMISCUOUS;
 		info("%s: Promiscuous mode enabled", net->name);
@@ -1154,8 +1152,6 @@ static void pegasus_set_multicast(struct net_device *net)
 
 	pegasus->flags |= ETH_REGS_CHANGE;
 	ctrl_callback(pegasus->ctrl_urb, NULL);
-
-	netif_wake_queue(net);
 }
 
 static __u8 mii_phy_probe(pegasus_t * pegasus)

drivers/usb/serial/generic.c

@@ -53,6 +53,32 @@ struct usb_serial_device_type usb_serial_generic_device = {
 	.num_ports =		1,
 	.shutdown =		usb_serial_generic_shutdown,
 };
+
+/* we want to look at all devices, as the vendor/product id can change
+ * depending on the command line argument */
+static struct usb_device_id generic_serial_ids[] = {
+	{.driver_info = 42},
+	{}
+};
+
+static int generic_probe(struct usb_interface *interface,
+			       const struct usb_device_id *id)
+{
+	const struct usb_device_id *id_pattern;
+
+	id_pattern = usb_match_id(interface, generic_device_ids);
+	if (id_pattern != NULL)
+		return usb_serial_probe(interface, id);
+	return -ENODEV;
+}
+
+static struct usb_driver generic_driver = {
+	.owner =	THIS_MODULE,
+	.name =		"usbserial_generic",
+	.probe =	generic_probe,
+	.disconnect =	usb_serial_disconnect,
+	.id_table =	generic_serial_ids,
+};
 #endif
 
 int usb_serial_generic_register (int _debug)
@@ -67,6 +93,12 @@ int usb_serial_generic_register (int _debug)
 
 	/* register our generic driver with ourselves */
 	retval = usb_serial_register (&usb_serial_generic_device);
+	if (retval)
+		goto exit;
+	retval = usb_register(&generic_driver);
+	if (retval)
+		usb_serial_deregister(&usb_serial_generic_device);
+exit:
 #endif
 	return retval;
 }
@@ -75,6 +107,7 @@ void usb_serial_generic_deregister (void)
 {
 #ifdef CONFIG_USB_SERIAL_GENERIC
 	/* remove our generic driver */
+	usb_deregister(&generic_driver);
 	usb_serial_deregister (&usb_serial_generic_device);
 #endif
 }

drivers/usb/serial/pl2303.c

@@ -62,7 +62,7 @@
 /*
  * Version Information
  */
-#define DRIVER_VERSION "v0.10"
+#define DRIVER_VERSION "v0.11"
 #define DRIVER_DESC "Prolific PL2303 USB to serial adaptor driver"
 
 
@@ -82,6 +82,7 @@ static struct usb_device_id id_table [] = {
 	{ USB_DEVICE(DCU10_VENDOR_ID, DCU10_PRODUCT_ID) },
 	{ USB_DEVICE(SITECOM_VENDOR_ID, SITECOM_PRODUCT_ID) },
 	{ USB_DEVICE(ALCATEL_VENDOR_ID, ALCATEL_PRODUCT_ID) },
+	{ USB_DEVICE(SAMSUNG_VENDOR_ID, SAMSUNG_PRODUCT_ID) },
 	{ }					/* Terminating entry */
 };
 
@@ -172,20 +173,38 @@ static struct usb_serial_device_type pl2303_device = {
 	.shutdown =		pl2303_shutdown,
 };
 
+enum pl2303_type {
+	type_0,		/* don't know the difference between type 0 and */
+	type_1,		/* type 1, until someone from prolific tells us... */
+	HX,		/* HX version of the pl2303 chip */
+};
+
 struct pl2303_private {
 	spinlock_t lock;
 	wait_queue_head_t delta_msr_wait;
 	u8 line_control;
 	u8 line_status;
 	u8 termios_initialized;
+	enum pl2303_type type;
 };
 
 
 static int pl2303_startup (struct usb_serial *serial)
 {
 	struct pl2303_private *priv;
+	enum pl2303_type type = type_0;
 	int i;
 
+	if (serial->dev->descriptor.bDeviceClass == 0x02)
+		type = type_0;
+	else if (serial->dev->descriptor.bMaxPacketSize0 == 0x40)
+		type = HX;
+	else if (serial->dev->descriptor.bDeviceClass == 0x00)
+		type = type_1;
+	else if (serial->dev->descriptor.bDeviceClass == 0xFF)
+		type = type_1;
+	dbg("device type: %d", type);
+
 	for (i = 0; i < serial->num_ports; ++i) {
 		priv = kmalloc (sizeof (struct pl2303_private), GFP_KERNEL);
 		if (!priv)
@@ -193,6 +212,7 @@ static int pl2303_startup (struct usb_serial *serial)
 		memset (priv, 0x00, sizeof (struct pl2303_private));
 		spin_lock_init(&priv->lock);
 		init_waitqueue_head(&priv->delta_msr_wait);
+		priv->type = type;
 		usb_set_serial_port_data(serial->port[i], priv);
 	}
 	return 0;
@@ -395,20 +415,27 @@ static void pl2303_set_termios (struct usb_serial_port *port, struct termios *ol
 	     buf[0], buf[1], buf[2], buf[3], buf[4], buf[5], buf[6]);
 
 	if (cflag & CRTSCTS) {
-		i = usb_control_msg (serial->dev, usb_sndctrlpipe (serial->dev, 0),
-				     VENDOR_WRITE_REQUEST, VENDOR_WRITE_REQUEST_TYPE,
-				     0x0, 0x41, NULL, 0, 100);
-		dbg ("0x40:0x1:0x0:0x41  %d", i);
+		__u16 index;
+		if (priv->type == HX)
+			index = 0x61;
+		else
+			index = 0x41;
+		i = usb_control_msg(serial->dev, 
+				    usb_sndctrlpipe(serial->dev, 0),
+				    VENDOR_WRITE_REQUEST,
+				    VENDOR_WRITE_REQUEST_TYPE,
+				    0x0, index, NULL, 0, 100);
+		dbg ("0x40:0x1:0x0:0x%x  %d", index, i);
 	}
 
 	kfree (buf);
 } 
 
-
 static int pl2303_open (struct usb_serial_port *port, struct file *filp)
 {
 	struct termios tmp_termios;
 	struct usb_serial *serial = port->serial;
+	struct pl2303_private *priv = usb_get_serial_port_data(port);
 	unsigned char *buf;
 	int result;
 
@@ -439,6 +466,18 @@ static int pl2303_open (struct usb_serial_port *port, struct file *filp)
 	SOUP (VENDOR_WRITE_REQUEST_TYPE, VENDOR_WRITE_REQUEST, 0x0404, 1);
 	FISH (VENDOR_READ_REQUEST_TYPE, VENDOR_READ_REQUEST, 0x8484, 0);
 	FISH (VENDOR_READ_REQUEST_TYPE, VENDOR_READ_REQUEST, 0x8383, 0);
+	SOUP (VENDOR_WRITE_REQUEST_TYPE, VENDOR_WRITE_REQUEST, 0, 1);
+	SOUP (VENDOR_WRITE_REQUEST_TYPE, VENDOR_WRITE_REQUEST, 1, 0);
+ 
+	if (priv->type == HX) {
+		/* HX chip */
+		SOUP (VENDOR_WRITE_REQUEST_TYPE, VENDOR_WRITE_REQUEST, 2, 0x44);
+		/* reset upstream data pipes */
+          	SOUP (VENDOR_WRITE_REQUEST_TYPE, VENDOR_WRITE_REQUEST, 8, 0);
+        	SOUP (VENDOR_WRITE_REQUEST_TYPE, VENDOR_WRITE_REQUEST, 9, 0);
+	} else {
+		SOUP (VENDOR_WRITE_REQUEST_TYPE, VENDOR_WRITE_REQUEST, 2, 0x24);
+	}
 
 	kfree(buf);
 

drivers/usb/serial/pl2303.h

@@ -42,5 +42,11 @@
 #define SITECOM_VENDOR_ID	0x6189
 #define SITECOM_PRODUCT_ID	0x2068
 
+/* Alcatel OT535/735 USB cable */
 #define ALCATEL_VENDOR_ID	0x11f7
 #define ALCATEL_PRODUCT_ID	0x02df
+
+/* Samsung I330 phone cradle */
+#define SAMSUNG_VENDOR_ID       0x04e8
+#define SAMSUNG_PRODUCT_ID      0x8001
+

drivers/usb/serial/usb-serial.c

@@ -355,25 +355,12 @@
 #define DRIVER_DESC "USB Serial Driver core"
 
 
-#ifdef CONFIG_USB_SERIAL_GENERIC
-/* we want to look at all devices, as the vendor/product id can change
- * depending on the command line argument */
-static struct usb_device_id generic_serial_ids[] = {
-	{.driver_info = 42},
-	{}
-};
-
-#endif /* CONFIG_USB_SERIAL_GENERIC */
-
 /* Driver structure we register with the USB core */
 static struct usb_driver usb_serial_driver = {
 	.owner =	THIS_MODULE,
 	.name =		"usbserial",
 	.probe =	usb_serial_probe,
 	.disconnect =	usb_serial_disconnect,
-#ifdef CONFIG_USB_SERIAL_GENERIC
-	.id_table =	generic_serial_ids,
-#endif
 };
 
 /* There is no MODULE_DEVICE_TABLE for usbserial.c.  Instead
@@ -1383,22 +1370,9 @@ int usb_serial_register(struct usb_serial_device_type *new_device)
 
 void usb_serial_deregister(struct usb_serial_device_type *device)
 {
-	struct usb_serial *serial;
-	int i;
-
 	info("USB Serial deregistering driver %s", device->name);
-
-	/* clear out the serial_table if the device is attached to a port */
-	for(i = 0; i < SERIAL_TTY_MINORS; ++i) {
-		serial = serial_table[i];
-		if ((serial != NULL) && (serial->type == device)) {
-			usb_driver_release_interface (&usb_serial_driver, serial->interface);
-			usb_serial_disconnect (serial->interface);
-		}
-	}
-
 	list_del(&device->driver_list);
-	usb_serial_bus_deregister (device);
+	usb_serial_bus_deregister(device);
 }
 
 

drivers/usb/storage/transport.c

@@ -708,6 +708,12 @@ void usb_stor_invoke_transport(Scsi_Cmnd *srb, struct us_data *us)
 			srb->sense_buffer[0] = 0x0;
 		}
 	}
+
+	/* Did we transfer less than the minimum amount required? */
+	if (srb->result == SAM_STAT_GOOD &&
+			srb->request_bufflen - srb->resid < srb->underflow)
+		srb->result = (DID_ERROR << 16) | (SUGGEST_RETRY << 24);
+
 	return;
 
 	/* abort processing: the bulk-only transport requires a reset

drivers/usb/storage/unusual_devs.h

@@ -73,6 +73,16 @@ UNUSUAL_DEV(  0x03f0, 0x0307, 0x0001, 0x0001,
 		US_SC_8070, US_PR_SCM_ATAPI, init_8200e, 0), 
 #endif
 
+/* <torsten.scherer@uni-bielefeld.de>: I don't know the name of the bridge
+ * manufacturer, but I've got an external USB drive by the Revoltec company
+ * that needs this. otherwise the drive is recognized as /dev/sda, but any
+ * access to it blocks indefinitely.
+ */
+UNUSUAL_DEV(  0x0402, 0x5621, 0x0103, 0x0103,
+		"Revoltec",
+		"USB/IDE Bridge (ATA/ATAPI)",
+		US_SC_DEVICE, US_PR_DEVICE, NULL, US_FL_FIX_INQUIRY),
+
 /* Deduced by Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
  * Entry needed for flags: US_FL_FIX_INQUIRY because initial inquiry message
  * always fails and confuses drive.
@@ -686,7 +696,7 @@ UNUSUAL_DEV( 0x090c, 0x1132, 0x0000, 0xffff,
 UNUSUAL_DEV(  0x097a, 0x0001, 0x0000, 0x0001,
 		"Minds@Work",
 		"Digital Wallet",
- 		US_SC_SCSI, US_PR_CB, NULL,
+ 		US_SC_DEVICE, US_PR_DEVICE, NULL,
 		US_FL_MODE_XLATE ),
 
 UNUSUAL_DEV(  0x0a16, 0x8888, 0x0100, 0x0100,

fs/aio.c

@@ -624,6 +624,7 @@ void fastcall kick_iocb(struct kiocb *iocb)
 		queue_work(aio_wq, &ctx->wq);
 	}
 }
+EXPORT_SYMBOL(kick_iocb);
 
 /* aio_complete
  *	Called when the io request on the given iocb is complete.