thermal/drivers/qcom: Add support for LMh driver

Driver enabling various pieces of Limits Management Hardware(LMh) for cpu
cluster0 and cpu cluster1 namely kick starting monitoring of temperature,
current, battery current violations, enabling reliability algorithm and
setting up various temperature limits.

The following has been explained in the cover letter. I am including this
here so that this remains in the commit message as well.

LMh is a hardware infrastructure on some Qualcomm SoCs that can enforce
temperature and current limits as programmed by software for certain IPs
like CPU. On many newer LMh is configured by firmware/TZ and no programming
is needed from the kernel side. But on certain SoCs like sdm845 the
firmware does not do a complete programming of the h/w. On such soc's
kernel software has to explicitly set up the temperature limits and turn on
various monitoring and enforcing algorithms on the hardware.

Tested-by: Steev Klimaszewski <steev@kali.org> # Lenovo Yoga C630
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210809191605.3742979-3-thara.gopinath@linaro.org

drivers/thermal/qcom/Kconfig

@@ -31,3 +31,13 @@ config QCOM_SPMI_TEMP_ALARM
 	  trip points. The temperature reported by the thermal sensor reflects the
 	  real time die temperature if an ADC is present or an estimate of the
 	  temperature based upon the over temperature stage value.
+
+config QCOM_LMH
+	tristate "Qualcomm Limits Management Hardware"
+	depends on ARCH_QCOM
+	help
+	  This enables initialization of Qualcomm limits management
+	  hardware(LMh). LMh allows for hardware-enforced mitigation for cpus based on
+	  input from temperature and current sensors.  On many newer Qualcomm SoCs
+	  LMh is configured in the firmware and this feature need not be enabled.
+	  However, on certain SoCs like sdm845 LMh has to be configured from kernel.

drivers/thermal/qcom/Makefile

@@ -5,3 +5,4 @@ qcom_tsens-y			+= tsens.o tsens-v2.o tsens-v1.o tsens-v0_1.o \
 				   tsens-8960.o
 obj-$(CONFIG_QCOM_SPMI_ADC_TM5)	+= qcom-spmi-adc-tm5.o
 obj-$(CONFIG_QCOM_SPMI_TEMP_ALARM)	+= qcom-spmi-temp-alarm.o
+obj-$(CONFIG_QCOM_LMH)		+= lmh.o

drivers/thermal/qcom/lmh.c

+// SPDX-License-Identifier: GPL-2.0-only
+
+/*
+ * Copyright (C) 2021, Linaro Limited. All rights reserved.
+ */
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/irqdomain.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/of_platform.h>
+#include <linux/slab.h>
+#include <linux/qcom_scm.h>
+
+#define LMH_NODE_DCVS			0x44435653
+#define LMH_CLUSTER0_NODE_ID		0x6370302D
+#define LMH_CLUSTER1_NODE_ID		0x6370312D
+
+#define LMH_SUB_FN_THERMAL		0x54484D4C
+#define LMH_SUB_FN_CRNT			0x43524E54
+#define LMH_SUB_FN_REL			0x52454C00
+#define LMH_SUB_FN_BCL			0x42434C00
+
+#define LMH_ALGO_MODE_ENABLE		0x454E424C
+#define LMH_TH_HI_THRESHOLD		0x48494748
+#define LMH_TH_LOW_THRESHOLD		0x4C4F5700
+#define LMH_TH_ARM_THRESHOLD		0x41524D00
+
+#define LMH_REG_DCVS_INTR_CLR		0x8
+
+struct lmh_hw_data {
+	void __iomem *base;
+	struct irq_domain *domain;
+	int irq;
+};
+
+static irqreturn_t lmh_handle_irq(int hw_irq, void *data)
+{
+	struct lmh_hw_data *lmh_data = data;
+	int irq = irq_find_mapping(lmh_data->domain, 0);
+
+	/* Call the cpufreq driver to handle the interrupt */
+	if (irq)
+		generic_handle_irq(irq);
+
+	return 0;
+}
+
+static void lmh_enable_interrupt(struct irq_data *d)
+{
+	struct lmh_hw_data *lmh_data = irq_data_get_irq_chip_data(d);
+
+	/* Clear the existing interrupt */
+	writel(0xff, lmh_data->base + LMH_REG_DCVS_INTR_CLR);
+	enable_irq(lmh_data->irq);
+}
+
+static void lmh_disable_interrupt(struct irq_data *d)
+{
+	struct lmh_hw_data *lmh_data = irq_data_get_irq_chip_data(d);
+
+	disable_irq_nosync(lmh_data->irq);
+}
+
+static struct irq_chip lmh_irq_chip = {
+	.name           = "lmh",
+	.irq_enable	= lmh_enable_interrupt,
+	.irq_disable	= lmh_disable_interrupt
+};
+
+static int lmh_irq_map(struct irq_domain *d, unsigned int irq, irq_hw_number_t hw)
+{
+	struct lmh_hw_data *lmh_data = d->host_data;
+
+	irq_set_chip_and_handler(irq, &lmh_irq_chip, handle_simple_irq);
+	irq_set_chip_data(irq, lmh_data);
+
+	return 0;
+}
+
+static const struct irq_domain_ops lmh_irq_ops = {
+	.map = lmh_irq_map,
+	.xlate = irq_domain_xlate_onecell,
+};
+
+static int lmh_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct device_node *cpu_node;
+	struct lmh_hw_data *lmh_data;
+	int temp_low, temp_high, temp_arm, cpu_id, ret;
+	u32 node_id;
+
+	lmh_data = devm_kzalloc(dev, sizeof(*lmh_data), GFP_KERNEL);
+	if (!lmh_data)
+		return -ENOMEM;
+
+	lmh_data->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(lmh_data->base))
+		return PTR_ERR(lmh_data->base);
+
+	cpu_node = of_parse_phandle(np, "cpus", 0);
+	if (!cpu_node)
+		return -EINVAL;
+	cpu_id = of_cpu_node_to_id(cpu_node);
+	of_node_put(cpu_node);
+
+	ret = of_property_read_u32(np, "qcom,lmh-temp-high-millicelsius", &temp_high);
+	if (ret) {
+		dev_err(dev, "missing qcom,lmh-temp-high-millicelsius property\n");
+		return ret;
+	}
+
+	ret = of_property_read_u32(np, "qcom,lmh-temp-low-millicelsius", &temp_low);
+	if (ret) {
+		dev_err(dev, "missing qcom,lmh-temp-low-millicelsius property\n");
+		return ret;
+	}
+
+	ret = of_property_read_u32(np, "qcom,lmh-temp-arm-millicelsius", &temp_arm);
+	if (ret) {
+		dev_err(dev, "missing qcom,lmh-temp-arm-millicelsius property\n");
+		return ret;
+	}
+
+	/*
+	 * Only sdm845 has lmh hardware currently enabled from hlos. If this is needed
+	 * for other platforms, revisit this to check if the <cpu-id, node-id> should be part
+	 * of a dt match table.
+	 */
+	if (cpu_id == 0) {
+		node_id = LMH_CLUSTER0_NODE_ID;
+	} else if (cpu_id == 4) {
+		node_id = LMH_CLUSTER1_NODE_ID;
+	} else {
+		dev_err(dev, "Wrong CPU id associated with LMh node\n");
+		return -EINVAL;
+	}
+
+	if (!qcom_scm_lmh_dcvsh_available())
+		return -EINVAL;
+
+	ret = qcom_scm_lmh_dcvsh(LMH_SUB_FN_CRNT, LMH_ALGO_MODE_ENABLE, 1,
+				 LMH_NODE_DCVS, node_id, 0);
+	if (ret)
+		dev_err(dev, "Error %d enabling current subfunction\n", ret);
+
+	ret = qcom_scm_lmh_dcvsh(LMH_SUB_FN_REL, LMH_ALGO_MODE_ENABLE, 1,
+				 LMH_NODE_DCVS, node_id, 0);
+	if (ret)
+		dev_err(dev, "Error %d enabling reliability subfunction\n", ret);
+
+	ret = qcom_scm_lmh_dcvsh(LMH_SUB_FN_BCL, LMH_ALGO_MODE_ENABLE, 1,
+				 LMH_NODE_DCVS, node_id, 0);
+	if (ret)
+		dev_err(dev, "Error %d enabling BCL subfunction\n", ret);
+
+	ret = qcom_scm_lmh_dcvsh(LMH_SUB_FN_THERMAL, LMH_ALGO_MODE_ENABLE, 1,
+				 LMH_NODE_DCVS, node_id, 0);
+	if (ret) {
+		dev_err(dev, "Error %d enabling thermal subfunction\n", ret);
+		return ret;
+	}
+
+	ret = qcom_scm_lmh_profile_change(0x1);
+	if (ret) {
+		dev_err(dev, "Error %d changing profile\n", ret);
+		return ret;
+	}
+
+	/* Set default thermal trips */
+	ret = qcom_scm_lmh_dcvsh(LMH_SUB_FN_THERMAL, LMH_TH_ARM_THRESHOLD, temp_arm,
+				 LMH_NODE_DCVS, node_id, 0);
+	if (ret) {
+		dev_err(dev, "Error setting thermal ARM threshold%d\n", ret);
+		return ret;
+	}
+
+	ret = qcom_scm_lmh_dcvsh(LMH_SUB_FN_THERMAL, LMH_TH_HI_THRESHOLD, temp_high,
+				 LMH_NODE_DCVS, node_id, 0);
+	if (ret) {
+		dev_err(dev, "Error setting thermal HI threshold%d\n", ret);
+		return ret;
+	}
+
+	ret = qcom_scm_lmh_dcvsh(LMH_SUB_FN_THERMAL, LMH_TH_LOW_THRESHOLD, temp_low,
+				 LMH_NODE_DCVS, node_id, 0);
+	if (ret) {
+		dev_err(dev, "Error setting thermal ARM threshold%d\n", ret);
+		return ret;
+	}
+
+	lmh_data->irq = platform_get_irq(pdev, 0);
+	lmh_data->domain = irq_domain_add_linear(np, 1, &lmh_irq_ops, lmh_data);
+	if (!lmh_data->domain) {
+		dev_err(dev, "Error adding irq_domain\n");
+		return -EINVAL;
+	}
+
+	/* Disable the irq and let cpufreq enable it when ready to handle the interrupt */
+	irq_set_status_flags(lmh_data->irq, IRQ_NOAUTOEN);
+	ret = devm_request_irq(dev, lmh_data->irq, lmh_handle_irq,
+			       IRQF_ONESHOT | IRQF_NO_SUSPEND,
+			       "lmh-irq", lmh_data);
+	if (ret) {
+		dev_err(dev, "Error %d registering irq %x\n", ret, lmh_data->irq);
+		irq_domain_remove(lmh_data->domain);
+		return ret;
+	}
+
+	return 0;
+}
+
+static const struct of_device_id lmh_table[] = {
+	{ .compatible = "qcom,sdm845-lmh", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, lmh_table);
+
+static struct platform_driver lmh_driver = {
+	.probe = lmh_probe,
+	.driver = {
+		.name = "qcom-lmh",
+		.of_match_table = lmh_table,
+		.suppress_bind_attrs = true,
+	},
+};
+module_platform_driver(lmh_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("QCOM LMh driver");