Commit 5756ee99 authored by Alan Cox's avatar Alan Cox Committed by Linus Torvalds

8250_pci: coding style

Signed-off-by: default avatarAlan Cox <alan@redhat.com>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
parent 3b0fd36d
......@@ -227,7 +227,7 @@ static int pci_inteli960ni_init(struct pci_dev *dev)
return -ENODEV;
/* is firmware started? */
pci_read_config_dword(dev, 0x44, (void*) &oldval);
pci_read_config_dword(dev, 0x44, (void *)&oldval);
if (oldval == 0x00001000L) { /* RESET value */
printk(KERN_DEBUG "Local i960 firmware missing");
return -ENODEV;
......@@ -253,11 +253,11 @@ static int pci_plx9050_init(struct pci_dev *dev)
irq_config = 0x41;
if (dev->vendor == PCI_VENDOR_ID_PANACOM ||
dev->subsystem_vendor == PCI_SUBVENDOR_ID_EXSYS) {
dev->subsystem_vendor == PCI_SUBVENDOR_ID_EXSYS)
irq_config = 0x43;
}
if ((dev->vendor == PCI_VENDOR_ID_PLX) &&
(dev->device == PCI_DEVICE_ID_PLX_ROMULUS)) {
(dev->device == PCI_DEVICE_ID_PLX_ROMULUS))
/*
* As the megawolf cards have the int pins active
* high, and have 2 UART chips, both ints must be
......@@ -267,8 +267,6 @@ static int pci_plx9050_init(struct pci_dev *dev)
* deep FIFOs
*/
irq_config = 0x5b;
}
/*
* enable/disable interrupts
*/
......@@ -343,14 +341,14 @@ static int sbs_init(struct pci_dev *dev)
{
u8 __iomem *p;
p = ioremap(pci_resource_start(dev, 0),pci_resource_len(dev,0));
p = ioremap(pci_resource_start(dev, 0), pci_resource_len(dev, 0));
if (p == NULL)
return -ENOMEM;
/* Set bit-4 Control Register (UART RESET) in to reset the uarts */
writeb(0x10,p + OCT_REG_CR_OFF);
writeb(0x10, p + OCT_REG_CR_OFF);
udelay(50);
writeb(0x0,p + OCT_REG_CR_OFF);
writeb(0x0, p + OCT_REG_CR_OFF);
/* Set bit-2 (INTENABLE) of Control Register */
writeb(0x4, p + OCT_REG_CR_OFF);
......@@ -367,10 +365,10 @@ static void __devexit sbs_exit(struct pci_dev *dev)
{
u8 __iomem *p;
p = ioremap(pci_resource_start(dev, 0),pci_resource_len(dev,0));
if (p != NULL) {
p = ioremap(pci_resource_start(dev, 0), pci_resource_len(dev, 0));
/* FIXME: What if resource_len < OCT_REG_CR_OFF */
if (p != NULL)
writeb(0, p + OCT_REG_CR_OFF);
}
iounmap(p);
}
......@@ -656,7 +654,8 @@ static int pci_ite887x_init(struct pci_dev *dev)
ITE_887x_POSIO_ENABLE | ITE_887x_POSIO_SPEED |
ITE_887x_POSIO_IOSIZE_32 | inta_addr[i]);
/* write INTCBAR - ioport */
pci_write_config_dword(dev, ITE_887x_INTCBAR, inta_addr[i]);
pci_write_config_dword(dev, ITE_887x_INTCBAR,
inta_addr[i]);
ret = inb(inta_addr[i]);
if (ret != 0xff) {
/* ioport connected */
......@@ -1711,7 +1710,7 @@ static struct pciserial_board pci_boards[] __devinitdata = {
};
static const struct pci_device_id softmodem_blacklist[] = {
{ PCI_VDEVICE ( AL, 0x5457 ), }, /* ALi Corporation M5457 AC'97 Modem */
{ PCI_VDEVICE(AL, 0x5457), }, /* ALi Corporation M5457 AC'97 Modem */
};
/*
......@@ -1863,7 +1862,7 @@ pciserial_init_ports(struct pci_dev *dev, struct pciserial_board *board)
break;
#ifdef SERIAL_DEBUG_PCI
printk("Setup PCI port: port %x, irq %d, type %d\n",
printk(KERN_DEBUG "Setup PCI port: port %x, irq %d, type %d\n",
serial_port.iobase, serial_port.irq, serial_port.iotype);
#endif
......@@ -1873,15 +1872,13 @@ pciserial_init_ports(struct pci_dev *dev, struct pciserial_board *board)
break;
}
}
priv->nr = i;
return priv;
err_deinit:
err_deinit:
if (quirk->exit)
quirk->exit(dev);
err_out:
err_out:
return priv;
}
EXPORT_SYMBOL_GPL(pciserial_init_ports);
......@@ -2269,10 +2266,12 @@ static struct pci_device_id serial_pci_tbl[] = {
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_8_115200 },
{ PCI_VENDOR_ID_SPECIALIX, PCI_DEVICE_ID_OXSEMI_16PCI954,
PCI_VENDOR_ID_SPECIALIX, PCI_SUBDEVICE_ID_SPECIALIX_SPEED4, 0, 0,
PCI_VENDOR_ID_SPECIALIX, PCI_SUBDEVICE_ID_SPECIALIX_SPEED4,
0, 0,
pbn_b0_4_921600 },
{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI954,
PCI_SUBVENDOR_ID_SIIG, PCI_SUBDEVICE_ID_SIIG_QUARTET_SERIAL, 0, 0,
PCI_SUBVENDOR_ID_SIIG, PCI_SUBDEVICE_ID_SIIG_QUARTET_SERIAL,
0, 0,
pbn_b0_4_1152000 },
/*
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment