drm/i915: reindent Haswell register definitions

It's the only part of the i915_reg.h file that looks totally wrongly
indented, so I assume my editor config is the correct one.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drivers/gpu/drm/i915/i915_reg.h

@@ -4295,8 +4295,7 @@
 #define PIPE_DDI_FUNC_CTL_B		0x61400
 #define PIPE_DDI_FUNC_CTL_C		0x62400
 #define PIPE_DDI_FUNC_CTL_EDP		0x6F400
-#define DDI_FUNC_CTL(pipe) _PIPE(pipe, \
-					PIPE_DDI_FUNC_CTL_A, \
+#define DDI_FUNC_CTL(pipe) _PIPE(pipe, PIPE_DDI_FUNC_CTL_A, \
 				       PIPE_DDI_FUNC_CTL_B)
 #define  PIPE_DDI_FUNC_ENABLE		(1<<31)
 /* Those bits are ignored by pipe EDP since it can only connect to DDI A */
@@ -4323,9 +4322,7 @@
 /* DisplayPort Transport Control */
 #define DP_TP_CTL_A			0x64040
 #define DP_TP_CTL_B			0x64140
-#define DP_TP_CTL(port) _PORT(port, \
-					DP_TP_CTL_A, \
-					DP_TP_CTL_B)
+#define DP_TP_CTL(port) _PORT(port, DP_TP_CTL_A, DP_TP_CTL_B)
 #define  DP_TP_CTL_ENABLE			(1<<31)
 #define  DP_TP_CTL_MODE_SST			(0<<27)
 #define  DP_TP_CTL_MODE_MST			(1<<27)
@@ -4339,17 +4336,13 @@
 /* DisplayPort Transport Status */
 #define DP_TP_STATUS_A			0x64044
 #define DP_TP_STATUS_B			0x64144
-#define DP_TP_STATUS(port) _PORT(port, \
-					DP_TP_STATUS_A, \
-					DP_TP_STATUS_B)
+#define DP_TP_STATUS(port) _PORT(port, DP_TP_STATUS_A, DP_TP_STATUS_B)
 #define  DP_TP_STATUS_AUTOTRAIN_DONE	(1<<12)
 
 /* DDI Buffer Control */
 #define DDI_BUF_CTL_A				0x64000
 #define DDI_BUF_CTL_B				0x64100
-#define DDI_BUF_CTL(port) _PORT(port, \
-					DDI_BUF_CTL_A, \
-					DDI_BUF_CTL_B)
+#define DDI_BUF_CTL(port) _PORT(port, DDI_BUF_CTL_A, DDI_BUF_CTL_B)
 #define  DDI_BUF_CTL_ENABLE			(1<<31)
 #define  DDI_BUF_EMP_400MV_0DB_HSW		(0<<24)   /* Sel0 */
 #define  DDI_BUF_EMP_400MV_3_5DB_HSW		(1<<24)   /* Sel1 */
@@ -4370,9 +4363,7 @@
 /* DDI Buffer Translations */
 #define DDI_BUF_TRANS_A				0x64E00
 #define DDI_BUF_TRANS_B				0x64E60
-#define DDI_BUF_TRANS(port) _PORT(port, \
-					DDI_BUF_TRANS_A, \
-					DDI_BUF_TRANS_B)
+#define DDI_BUF_TRANS(port) _PORT(port, DDI_BUF_TRANS_A, DDI_BUF_TRANS_B)
 
 /* Sideband Interface (SBI) is programmed indirectly, via
  * SBI_ADDR, which contains the register offset; and SBI_DATA,
@@ -4430,9 +4421,7 @@
 /* Port clock selection */
 #define PORT_CLK_SEL_A			0x46100
 #define PORT_CLK_SEL_B			0x46104
-#define PORT_CLK_SEL(port) _PORT(port, \
-					PORT_CLK_SEL_A, \
-					PORT_CLK_SEL_B)
+#define PORT_CLK_SEL(port) _PORT(port, PORT_CLK_SEL_A, PORT_CLK_SEL_B)
 #define  PORT_CLK_SEL_LCPLL_2700	(0<<29)
 #define  PORT_CLK_SEL_LCPLL_1350	(1<<29)
 #define  PORT_CLK_SEL_LCPLL_810		(2<<29)
@@ -4443,9 +4432,7 @@
 /* Pipe clock selection */
 #define PIPE_CLK_SEL_A			0x46140
 #define PIPE_CLK_SEL_B			0x46144
-#define PIPE_CLK_SEL(pipe) _PIPE(pipe, \
-					PIPE_CLK_SEL_A, \
-					PIPE_CLK_SEL_B)
+#define PIPE_CLK_SEL(pipe) _PIPE(pipe, PIPE_CLK_SEL_A, PIPE_CLK_SEL_B)
 /* For each pipe, we need to select the corresponding port clock */
 #define  PIPE_CLK_SEL_DISABLED		(0x0<<29)
 #define  PIPE_CLK_SEL_PORT(x)		((x+1)<<29)
@@ -4460,8 +4447,7 @@
 /* Pipe WM_LINETIME - watermark line time */
 #define PIPE_WM_LINETIME_A		0x45270
 #define PIPE_WM_LINETIME_B		0x45274
-#define PIPE_WM_LINETIME(pipe) _PIPE(pipe, \
-					PIPE_WM_LINETIME_A, \
+#define PIPE_WM_LINETIME(pipe) _PIPE(pipe, PIPE_WM_LINETIME_A, \
 					   PIPE_WM_LINETIME_B)
 #define   PIPE_WM_LINETIME_MASK			(0x1ff)
 #define   PIPE_WM_LINETIME_TIME(x)		((x))