Merge TI ringacc driver from Santosh

This is for dependency of new TI ringacc dmaengine drivers

Merge tag 'drivers_soc_for_5.6' into topic/ti

SOC: TI Keystone Ring Accelerator driver

The Ring Accelerator (RINGACC or RA) provides hardware acceleration to
enable straightforward passing of work between a producer and a consumer.
There is one RINGACC module per NAVSS on TI AM65x SoCs.
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Documentation/devicetree/bindings/soc/ti/k3-ringacc.txt

+* Texas Instruments K3 NavigatorSS Ring Accelerator
+
+The Ring Accelerator (RA) is a machine which converts read/write accesses
+from/to a constant address into corresponding read/write accesses from/to a
+circular data structure in memory. The RA eliminates the need for each DMA
+controller which needs to access ring elements from having to know the current
+state of the ring (base address, current offset). The DMA controller
+performs a read or write access to a specific address range (which maps to the
+source interface on the RA) and the RA replaces the address for the transaction
+with a new address which corresponds to the head or tail element of the ring
+(head for reads, tail for writes).
+
+The Ring Accelerator is a hardware module that is responsible for accelerating
+management of the packet queues. The K3 SoCs can have more than one RA instances
+
+Required properties:
+- compatible	: Must be "ti,am654-navss-ringacc";
+- reg		: Should contain register location and length of the following
+		  named register regions.
+- reg-names	: should be
+		  "rt" - The RA Ring Real-time Control/Status Registers
+		  "fifos" - The RA Queues Registers
+		  "proxy_gcfg" - The RA Proxy Global Config Registers
+		  "proxy_target" - The RA Proxy Datapath Registers
+- ti,num-rings	: Number of rings supported by RA
+- ti,sci-rm-range-gp-rings : TI-SCI RM subtype for GP ring range
+- ti,sci	: phandle on TI-SCI compatible System controller node
+- ti,sci-dev-id	: TI-SCI device id of the ring accelerator
+- msi-parent	: phandle for "ti,sci-inta" interrupt controller
+
+Optional properties:
+ -- ti,dma-ring-reset-quirk : enable ringacc / udma ring state interoperability
+		  issue software w/a
+
+Example:
+
+ringacc: ringacc@3c000000 {
+	compatible = "ti,am654-navss-ringacc";
+	reg =	<0x0 0x3c000000 0x0 0x400000>,
+		<0x0 0x38000000 0x0 0x400000>,
+		<0x0 0x31120000 0x0 0x100>,
+		<0x0 0x33000000 0x0 0x40000>;
+	reg-names = "rt", "fifos",
+		    "proxy_gcfg", "proxy_target";
+	ti,num-rings = <818>;
+	ti,sci-rm-range-gp-rings = <0x2>; /* GP ring range */
+	ti,dma-ring-reset-quirk;
+	ti,sci = <&dmsc>;
+	ti,sci-dev-id = <187>;
+	msi-parent = <&inta_main_udmass>;
+};
+
+client:
+
+dma_ipx: dma_ipx@<addr> {
+	...
+	ti,ringacc = <&ringacc>;
+	...
+}

drivers/soc/ti/Kconfig

@@ -80,6 +80,17 @@ config TI_SCI_PM_DOMAINS
 	  called ti_sci_pm_domains. Note this is needed early in boot before
 	  rootfs may be available.
 
+config TI_K3_RINGACC
+	bool "K3 Ring accelerator Sub System"
+	depends on ARCH_K3 || COMPILE_TEST
+	depends on TI_SCI_INTA_IRQCHIP
+	help
+	  Say y here to support the K3 Ring accelerator module.
+	  The Ring Accelerator (RINGACC or RA)  provides hardware acceleration
+	  to enable straightforward passing of work between a producer
+	  and a consumer. There is one RINGACC module per NAVSS on TI AM65x SoCs
+	  If unsure, say N.
+
 endif # SOC_TI
 
 config TI_SCI_INTA_MSI_DOMAIN

drivers/soc/ti/Makefile

@@ -10,3 +10,4 @@ obj-$(CONFIG_ARCH_OMAP2PLUS)		+= omap_prm.o
 obj-$(CONFIG_WKUP_M3_IPC)		+= wkup_m3_ipc.o
 obj-$(CONFIG_TI_SCI_PM_DOMAINS)		+= ti_sci_pm_domains.o
 obj-$(CONFIG_TI_SCI_INTA_MSI_DOMAIN)	+= ti_sci_inta_msi.o
+obj-$(CONFIG_TI_K3_RINGACC)		+= k3-ringacc.o

include/linux/soc/ti/k3-ringacc.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * K3 Ring Accelerator (RA) subsystem interface
+ *
+ * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com
+ */
+
+#ifndef __SOC_TI_K3_RINGACC_API_H_
+#define __SOC_TI_K3_RINGACC_API_H_
+
+#include <linux/types.h>
+
+struct device_node;
+
+/**
+ * enum k3_ring_mode - &struct k3_ring_cfg mode
+ *
+ * RA ring operational modes
+ *
+ * @K3_RINGACC_RING_MODE_RING: Exposed Ring mode for SW direct access
+ * @K3_RINGACC_RING_MODE_MESSAGE: Messaging mode. Messaging mode requires
+ *	that all accesses to the queue must go through this IP so that all
+ *	accesses to the memory are controlled and ordered. This IP then
+ *	controls the entire state of the queue, and SW has no directly control,
+ *	such as through doorbells and cannot access the storage memory directly.
+ *	This is particularly useful when more than one SW or HW entity can be
+ *	the producer and/or consumer at the same time
+ * @K3_RINGACC_RING_MODE_CREDENTIALS: Credentials mode is message mode plus
+ *	stores credentials with each message, requiring the element size to be
+ *	doubled to fit the credentials. Any exposed memory should be protected
+ *	by a firewall from unwanted access
+ */
+enum k3_ring_mode {
+	K3_RINGACC_RING_MODE_RING = 0,
+	K3_RINGACC_RING_MODE_MESSAGE,
+	K3_RINGACC_RING_MODE_CREDENTIALS,
+	K3_RINGACC_RING_MODE_INVALID
+};
+
+/**
+ * enum k3_ring_size - &struct k3_ring_cfg elm_size
+ *
+ * RA ring element's sizes in bytes.
+ */
+enum k3_ring_size {
+	K3_RINGACC_RING_ELSIZE_4 = 0,
+	K3_RINGACC_RING_ELSIZE_8,
+	K3_RINGACC_RING_ELSIZE_16,
+	K3_RINGACC_RING_ELSIZE_32,
+	K3_RINGACC_RING_ELSIZE_64,
+	K3_RINGACC_RING_ELSIZE_128,
+	K3_RINGACC_RING_ELSIZE_256,
+	K3_RINGACC_RING_ELSIZE_INVALID
+};
+
+struct k3_ringacc;
+struct k3_ring;
+
+/**
+ * enum k3_ring_cfg - RA ring configuration structure
+ *
+ * @size: Ring size, number of elements
+ * @elm_size: Ring element size
+ * @mode: Ring operational mode
+ * @flags: Ring configuration flags. Possible values:
+ *	 @K3_RINGACC_RING_SHARED: when set allows to request the same ring
+ *	 few times. It's usable when the same ring is used as Free Host PD ring
+ *	 for different flows, for example.
+ *	 Note: Locking should be done by consumer if required
+ */
+struct k3_ring_cfg {
+	u32 size;
+	enum k3_ring_size elm_size;
+	enum k3_ring_mode mode;
+#define K3_RINGACC_RING_SHARED BIT(1)
+	u32 flags;
+};
+
+#define K3_RINGACC_RING_ID_ANY (-1)
+
+/**
+ * of_k3_ringacc_get_by_phandle - find a RA by phandle property
+ * @np: device node
+ * @propname: property name containing phandle on RA node
+ *
+ * Returns pointer on the RA - struct k3_ringacc
+ * or -ENODEV if not found,
+ * or -EPROBE_DEFER if not yet registered
+ */
+struct k3_ringacc *of_k3_ringacc_get_by_phandle(struct device_node *np,
+						const char *property);
+
+#define K3_RINGACC_RING_USE_PROXY BIT(1)
+
+/**
+ * k3_ringacc_request_ring - request ring from ringacc
+ * @ringacc: pointer on ringacc
+ * @id: ring id or K3_RINGACC_RING_ID_ANY for any general purpose ring
+ * @flags:
+ *	@K3_RINGACC_RING_USE_PROXY: if set - proxy will be allocated and
+ *		used to access ring memory. Sopported only for rings in
+ *		Message/Credentials/Queue mode.
+ *
+ * Returns pointer on the Ring - struct k3_ring
+ * or NULL in case of failure.
+ */
+struct k3_ring *k3_ringacc_request_ring(struct k3_ringacc *ringacc,
+					int id, u32 flags);
+
+/**
+ * k3_ringacc_ring_reset - ring reset
+ * @ring: pointer on Ring
+ *
+ * Resets ring internal state ((hw)occ, (hw)idx).
+ */
+void k3_ringacc_ring_reset(struct k3_ring *ring);
+/**
+ * k3_ringacc_ring_reset - ring reset for DMA rings
+ * @ring: pointer on Ring
+ *
+ * Resets ring internal state ((hw)occ, (hw)idx). Should be used for rings
+ * which are read by K3 UDMA, like TX or Free Host PD rings.
+ */
+void k3_ringacc_ring_reset_dma(struct k3_ring *ring, u32 occ);
+
+/**
+ * k3_ringacc_ring_free - ring free
+ * @ring: pointer on Ring
+ *
+ * Resets ring and free all alocated resources.
+ */
+int k3_ringacc_ring_free(struct k3_ring *ring);
+
+/**
+ * k3_ringacc_get_ring_id - Get the Ring ID
+ * @ring: pointer on ring
+ *
+ * Returns the Ring ID
+ */
+u32 k3_ringacc_get_ring_id(struct k3_ring *ring);
+
+/**
+ * k3_ringacc_get_ring_irq_num - Get the irq number for the ring
+ * @ring: pointer on ring
+ *
+ * Returns the interrupt number which can be used to request the interrupt
+ */
+int k3_ringacc_get_ring_irq_num(struct k3_ring *ring);
+
+/**
+ * k3_ringacc_ring_cfg - ring configure
+ * @ring: pointer on ring
+ * @cfg: Ring configuration parameters (see &struct k3_ring_cfg)
+ *
+ * Configures ring, including ring memory allocation.
+ * Returns 0 on success, errno otherwise.
+ */
+int k3_ringacc_ring_cfg(struct k3_ring *ring, struct k3_ring_cfg *cfg);
+
+/**
+ * k3_ringacc_ring_get_size - get ring size
+ * @ring: pointer on ring
+ *
+ * Returns ring size in number of elements.
+ */
+u32 k3_ringacc_ring_get_size(struct k3_ring *ring);
+
+/**
+ * k3_ringacc_ring_get_free - get free elements
+ * @ring: pointer on ring
+ *
+ * Returns number of free elements in the ring.
+ */
+u32 k3_ringacc_ring_get_free(struct k3_ring *ring);
+
+/**
+ * k3_ringacc_ring_get_occ - get ring occupancy
+ * @ring: pointer on ring
+ *
+ * Returns total number of valid entries on the ring
+ */
+u32 k3_ringacc_ring_get_occ(struct k3_ring *ring);
+
+/**
+ * k3_ringacc_ring_is_full - checks if ring is full
+ * @ring: pointer on ring
+ *
+ * Returns true if the ring is full
+ */
+u32 k3_ringacc_ring_is_full(struct k3_ring *ring);
+
+/**
+ * k3_ringacc_ring_push - push element to the ring tail
+ * @ring: pointer on ring
+ * @elem: pointer on ring element buffer
+ *
+ * Push one ring element to the ring tail. Size of the ring element is
+ * determined by ring configuration &struct k3_ring_cfg elm_size.
+ *
+ * Returns 0 on success, errno otherwise.
+ */
+int k3_ringacc_ring_push(struct k3_ring *ring, void *elem);
+
+/**
+ * k3_ringacc_ring_pop - pop element from the ring head
+ * @ring: pointer on ring
+ * @elem: pointer on ring element buffer
+ *
+ * Push one ring element from the ring head. Size of the ring element is
+ * determined by ring configuration &struct k3_ring_cfg elm_size..
+ *
+ * Returns 0 on success, errno otherwise.
+ */
+int k3_ringacc_ring_pop(struct k3_ring *ring, void *elem);
+
+/**
+ * k3_ringacc_ring_push_head - push element to the ring head
+ * @ring: pointer on ring
+ * @elem: pointer on ring element buffer
+ *
+ * Push one ring element to the ring head. Size of the ring element is
+ * determined by ring configuration &struct k3_ring_cfg elm_size.
+ *
+ * Returns 0 on success, errno otherwise.
+ * Not Supported by ring modes: K3_RINGACC_RING_MODE_RING
+ */
+int k3_ringacc_ring_push_head(struct k3_ring *ring, void *elem);
+
+/**
+ * k3_ringacc_ring_pop_tail - pop element from the ring tail
+ * @ring: pointer on ring
+ * @elem: pointer on ring element buffer
+ *
+ * Push one ring element from the ring tail. Size of the ring element is
+ * determined by ring configuration &struct k3_ring_cfg elm_size.
+ *
+ * Returns 0 on success, errno otherwise.
+ * Not Supported by ring modes: K3_RINGACC_RING_MODE_RING
+ */
+int k3_ringacc_ring_pop_tail(struct k3_ring *ring, void *elem);
+
+u32 k3_ringacc_get_tisci_dev_id(struct k3_ring *ring);
+
+#endif /* __SOC_TI_K3_RINGACC_API_H_ */