wifi: wilc1000: remove use of has_thrpt_enh3 flag

The 'enhance throughput flow' algorithm is used by default. So older
sections of the code are removed so as to always use this new algorithm.
Signed-off-by: Prasurjya Rohan Saikia <prasurjya.rohansaikia@microchip.com>
Acked-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230710094401.235222-1-prasurjya.rohansaikia@microchip.com

drivers/net/wireless/microchip/wilc1000/sdio.c

@@ -28,7 +28,6 @@ struct wilc_sdio {
 	bool irq_gpio;
 	u32 block_size;
 	bool isinit;
-	int has_thrpt_enh3;
 	u8 *cmd53_buf;
 };
 
@@ -722,21 +721,12 @@ static int wilc_sdio_init(struct wilc *wilc, bool resume)
 	 *      make sure can read back chip id correctly
 	 **/
 	if (!resume) {
-		int rev;
-
 		ret = wilc_sdio_read_reg(wilc, WILC_CHIPID, &chipid);
 		if (ret) {
 			dev_err(&func->dev, "Fail cmd read chip id...\n");
 			return ret;
 		}
 		dev_err(&func->dev, "chipid (%08x)\n", chipid);
-		rev = FIELD_GET(WILC_CHIP_REV_FIELD, chipid);
-		if (rev > FIELD_GET(WILC_CHIP_REV_FIELD, WILC_1000_BASE_ID_2A))
-			sdio_priv->has_thrpt_enh3 = 1;
-		else
-			sdio_priv->has_thrpt_enh3 = 0;
-		dev_info(&func->dev, "has_thrpt_enh3 = %d...\n",
-			 sdio_priv->has_thrpt_enh3);
 	}
 
 	sdio_priv->isinit = true;
@@ -809,9 +799,6 @@ static int wilc_sdio_clear_int_ext(struct wilc *wilc, u32 val)
 	struct sdio_func *func = dev_to_sdio_func(wilc->dev);
 	struct wilc_sdio *sdio_priv = wilc->bus_data;
 	int ret;
-	int vmm_ctl;
-
-	if (sdio_priv->has_thrpt_enh3) {
 	u32 reg = 0;
 
 	if (sdio_priv->irq_gpio)
@@ -844,76 +831,6 @@ static int wilc_sdio_clear_int_ext(struct wilc *wilc, u32 val)
 		}
 	}
 	return 0;
-	}
-	if (sdio_priv->irq_gpio) {
-		/* has_thrpt_enh2 uses register 0xf8 to clear interrupts. */
-		/*
-		 * Cannot clear multiple interrupts.
-		 * Must clear each interrupt individually.
-		 */
-		u32 flags;
-		int i;
-
-		flags = val & (BIT(MAX_NUM_INT) - 1);
-		for (i = 0; i < NUM_INT_EXT && flags; i++) {
-			if (flags & BIT(i)) {
-				struct sdio_cmd52 cmd;
-
-				cmd.read_write = 1;
-				cmd.function = 0;
-				cmd.raw = 0;
-				cmd.address = WILC_SDIO_IRQ_CLEAR_FLAG_REG;
-				cmd.data = BIT(i);
-
-				ret = wilc_sdio_cmd52(wilc, &cmd);
-				if (ret) {
-					dev_err(&func->dev,
-						"Failed cmd52, set (%02x) data (%d) ...\n",
-						cmd.address, __LINE__);
-					return ret;
-				}
-				flags &= ~BIT(i);
-			}
-		}
-
-		for (i = NUM_INT_EXT; i < MAX_NUM_INT && flags; i++) {
-			if (flags & BIT(i)) {
-				dev_err(&func->dev,
-					"Unexpected interrupt cleared %d...\n",
-					i);
-				flags &= ~BIT(i);
-			}
-		}
-	}
-
-	vmm_ctl = 0;
-	/* select VMM table 0 */
-	if (val & SEL_VMM_TBL0)
-		vmm_ctl |= BIT(0);
-	/* select VMM table 1 */
-	if (val & SEL_VMM_TBL1)
-		vmm_ctl |= BIT(1);
-	/* enable VMM */
-	if (val & EN_VMM)
-		vmm_ctl |= BIT(2);
-
-	if (vmm_ctl) {
-		struct sdio_cmd52 cmd;
-
-		cmd.read_write = 1;
-		cmd.function = 0;
-		cmd.raw = 0;
-		cmd.address = WILC_SDIO_VMM_TBL_CTRL_REG;
-		cmd.data = vmm_ctl;
-		ret = wilc_sdio_cmd52(wilc, &cmd);
-		if (ret) {
-			dev_err(&func->dev,
-				"Failed cmd52, set (%02x) data (%d) ...\n",
-				cmd.address, __LINE__);
-			return ret;
-		}
-	}
-	return 0;
 }
 
 static int wilc_sdio_sync_ext(struct wilc *wilc, int nint)