Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [PCI] Add JMicron PCI ID constants
  [PATCH] ahci: Ensure that we don't grab both functions
  [PATCH] libata-core.c: restore configuration boot messages in ata_dev_configure(), v2
  [PATCH] sata_sil24: add suspend/sleep support
  [PATCH] sata_sil24: separate out sil24_init_controller()
  [PATCH] sata_sil: add suspend/sleep support
  [PATCH] sata_sil: separate out sil_init_controller()
  [PATCH] libata: reimplement controller-wide PM
  [PATCH] libata: reimplement per-dev PM
  [PATCH] libata: implement PM EH actions
  [PATCH] libata: separate out __ata_ehi_hotplugged()
  [PATCH] libata: implement ATA_EHI_NO_AUTOPSY and QUIET
  [PATCH] libata: clean up debounce parameters and improve parameter selection
  [PATCH] libata: implement ATA_EHI_RESUME_LINK
  [PATCH] libata: replace ap_lock w/ ap->lock in ata_scsi_error()
  [PATCH] libata: fix ehc->i.action setting in ata_eh_autopsy()
  [PATCH] libata: add ap->pflags and move core dynamic flags to it
  [PATCH] libata: Conditionally set host->max_cmd_len
  [PATCH] sata_vsc: data_xfer should use mmio

drivers/scsi/ahci.c

@@ -1052,7 +1052,7 @@ static void ahci_thaw(struct ata_port *ap)
 
 static void ahci_error_handler(struct ata_port *ap)
 {
-	if (!(ap->flags & ATA_FLAG_FROZEN)) {
+	if (!(ap->pflags & ATA_PFLAG_FROZEN)) {
 		/* restart engine */
 		ahci_stop_engine(ap);
 		ahci_start_engine(ap);
@@ -1323,6 +1323,17 @@ static int ahci_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 	if (!printed_version++)
 		dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
 
+	/* JMicron-specific fixup: make sure we're in AHCI mode */
+	/* This is protected from races with ata_jmicron by the pci probe
+	   locking */
+	if (pdev->vendor == PCI_VENDOR_ID_JMICRON) {
+		/* AHCI enable, AHCI on function 0 */
+		pci_write_config_byte(pdev, 0x41, 0xa1);
+		/* Function 1 is the PATA controller */
+		if (PCI_FUNC(pdev->devfn))
+			return -ENODEV;
+	}
+
 	rc = pci_enable_device(pdev);
 	if (rc)
 		return rc;
@@ -1378,10 +1389,6 @@ static int ahci_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 	if (have_msi)
 		hpriv->flags |= AHCI_FLAG_MSI;
 
-	/* JMicron-specific fixup: make sure we're in AHCI mode */
-	if (pdev->vendor == 0x197b)
-		pci_write_config_byte(pdev, 0x41, 0xa1);
-
 	/* initialize adapter */
 	rc = ahci_host_init(probe_ent);
 	if (rc)

drivers/scsi/libata-scsi.c

@@ -397,20 +397,129 @@ void ata_dump_status(unsigned id, struct ata_taskfile *tf)
 	}
 }
 
-int ata_scsi_device_resume(struct scsi_device *sdev)
+/**
+ *	ata_scsi_device_suspend - suspend ATA device associated with sdev
+ *	@sdev: the SCSI device to suspend
+ *	@state: target power management state
+ *
+ *	Request suspend EH action on the ATA device associated with
+ *	@sdev and wait for the operation to complete.
+ *
+ *	LOCKING:
+ *	Kernel thread context (may sleep).
+ *
+ *	RETURNS:
+ *	0 on success, -errno otherwise.
+ */
+int ata_scsi_device_suspend(struct scsi_device *sdev, pm_message_t state)
 {
 	struct ata_port *ap = ata_shost_to_port(sdev->host);
-	struct ata_device *dev = __ata_scsi_find_dev(ap, sdev);
+	struct ata_device *dev = ata_scsi_find_dev(ap, sdev);
+	unsigned long flags;
+	unsigned int action;
+	int rc = 0;
+
+	if (!dev)
+		goto out;
+
+	spin_lock_irqsave(ap->lock, flags);
+
+	/* wait for the previous resume to complete */
+	while (dev->flags & ATA_DFLAG_SUSPENDED) {
+		spin_unlock_irqrestore(ap->lock, flags);
+		ata_port_wait_eh(ap);
+		spin_lock_irqsave(ap->lock, flags);
+	}
+
+	/* if @sdev is already detached, nothing to do */
+	if (sdev->sdev_state == SDEV_OFFLINE ||
+	    sdev->sdev_state == SDEV_CANCEL || sdev->sdev_state == SDEV_DEL)
+		goto out_unlock;
+
+	/* request suspend */
+	action = ATA_EH_SUSPEND;
+	if (state.event != PM_EVENT_SUSPEND)
+		action |= ATA_EH_PM_FREEZE;
+	ap->eh_info.dev_action[dev->devno] |= action;
+	ap->eh_info.flags |= ATA_EHI_QUIET;
+	ata_port_schedule_eh(ap);
+
+	spin_unlock_irqrestore(ap->lock, flags);
+
+	/* wait for EH to do the job */
+	ata_port_wait_eh(ap);
+
+	spin_lock_irqsave(ap->lock, flags);
+
+	/* If @sdev is still attached but the associated ATA device
+	 * isn't suspended, the operation failed.
+	 */
+	if (sdev->sdev_state != SDEV_OFFLINE &&
+	    sdev->sdev_state != SDEV_CANCEL && sdev->sdev_state != SDEV_DEL &&
+	    !(dev->flags & ATA_DFLAG_SUSPENDED))
+		rc = -EIO;
 
-	return ata_device_resume(dev);
+ out_unlock:
+	spin_unlock_irqrestore(ap->lock, flags);
+ out:
+	if (rc == 0)
+		sdev->sdev_gendev.power.power_state = state;
+	return rc;
 }
 
-int ata_scsi_device_suspend(struct scsi_device *sdev, pm_message_t state)
+/**
+ *	ata_scsi_device_resume - resume ATA device associated with sdev
+ *	@sdev: the SCSI device to resume
+ *
+ *	Request resume EH action on the ATA device associated with
+ *	@sdev and return immediately.  This enables parallel
+ *	wakeup/spinup of devices.
+ *
+ *	LOCKING:
+ *	Kernel thread context (may sleep).
+ *
+ *	RETURNS:
+ *	0.
+ */
+int ata_scsi_device_resume(struct scsi_device *sdev)
 {
 	struct ata_port *ap = ata_shost_to_port(sdev->host);
-	struct ata_device *dev = __ata_scsi_find_dev(ap, sdev);
+	struct ata_device *dev = ata_scsi_find_dev(ap, sdev);
+	struct ata_eh_info *ehi = &ap->eh_info;
+	unsigned long flags;
+	unsigned int action;
+
+	if (!dev)
+		goto out;
+
+	spin_lock_irqsave(ap->lock, flags);
+
+	/* if @sdev is already detached, nothing to do */
+	if (sdev->sdev_state == SDEV_OFFLINE ||
+	    sdev->sdev_state == SDEV_CANCEL || sdev->sdev_state == SDEV_DEL)
+		goto out_unlock;
+
+	/* request resume */
+	action = ATA_EH_RESUME;
+	if (sdev->sdev_gendev.power.power_state.event == PM_EVENT_SUSPEND)
+		__ata_ehi_hotplugged(ehi);
+	else
+		action |= ATA_EH_PM_FREEZE | ATA_EH_SOFTRESET;
+	ehi->dev_action[dev->devno] |= action;
+
+	/* We don't want autopsy and verbose EH messages.  Disable
+	 * those if we're the only device on this link.
+	 */
+	if (ata_port_max_devices(ap) == 1)
+		ehi->flags |= ATA_EHI_NO_AUTOPSY | ATA_EHI_QUIET;
 
-	return ata_device_suspend(dev, state);
+	ata_port_schedule_eh(ap);
+
+ out_unlock:
+	spin_unlock_irqrestore(ap->lock, flags);
+ out:
+	sdev->sdev_gendev.power.power_state = PMSG_ON;
+	return 0;
 }
 
 /**
@@ -2930,7 +3039,7 @@ void ata_scsi_hotplug(void *data)
 	struct ata_port *ap = data;
 	int i;
 
-	if (ap->flags & ATA_FLAG_UNLOADING) {
+	if (ap->pflags & ATA_PFLAG_UNLOADING) {
 		DPRINTK("ENTER/EXIT - unloading\n");
 		return;
 	}
@@ -3011,6 +3120,7 @@ static int ata_scsi_user_scan(struct Scsi_Host *shost, unsigned int channel,
 		if (dev) {
 			ap->eh_info.probe_mask |= 1 << dev->devno;
 			ap->eh_info.action |= ATA_EH_SOFTRESET;
+			ap->eh_info.flags |= ATA_EHI_RESUME_LINK;
 		} else
 			rc = -EINVAL;
 	}

drivers/scsi/sata_sil.c

@@ -109,6 +109,7 @@ enum {
 };
 
 static int sil_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
+static int sil_pci_device_resume(struct pci_dev *pdev);
 static void sil_dev_config(struct ata_port *ap, struct ata_device *dev);
 static u32 sil_scr_read (struct ata_port *ap, unsigned int sc_reg);
 static void sil_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
@@ -160,6 +161,8 @@ static struct pci_driver sil_pci_driver = {
 	.id_table		= sil_pci_tbl,
 	.probe			= sil_init_one,
 	.remove			= ata_pci_remove_one,
+	.suspend		= ata_pci_device_suspend,
+	.resume			= sil_pci_device_resume,
 };
 
 static struct scsi_host_template sil_sht = {
@@ -178,6 +181,8 @@ static struct scsi_host_template sil_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.suspend		= ata_scsi_device_suspend,
+	.resume			= ata_scsi_device_resume,
 };
 
 static const struct ata_port_operations sil_ops = {
@@ -370,7 +375,7 @@ static void sil_host_intr(struct ata_port *ap, u32 bmdma2)
 		 * during hardreset makes controllers with broken SIEN
 		 * repeat probing needlessly.
 		 */
-		if (!(ap->flags & ATA_FLAG_FROZEN)) {
+		if (!(ap->pflags & ATA_PFLAG_FROZEN)) {
 			ata_ehi_hotplugged(&ap->eh_info);
 			ap->eh_info.serror |= serror;
 		}
@@ -561,6 +566,52 @@ static void sil_dev_config(struct ata_port *ap, struct ata_device *dev)
 	}
 }
 
+static void sil_init_controller(struct pci_dev *pdev,
+				int n_ports, unsigned long host_flags,
+				void __iomem *mmio_base)
+{
+	u8 cls;
+	u32 tmp;
+	int i;
+
+	/* Initialize FIFO PCI bus arbitration */
+	cls = sil_get_device_cache_line(pdev);
+	if (cls) {
+		cls >>= 3;
+		cls++;  /* cls = (line_size/8)+1 */
+		for (i = 0; i < n_ports; i++)
+			writew(cls << 8 | cls,
+			       mmio_base + sil_port[i].fifo_cfg);
+	} else
+		dev_printk(KERN_WARNING, &pdev->dev,
+			   "cache line size not set.  Driver may not function\n");
+
+	/* Apply R_ERR on DMA activate FIS errata workaround */
+	if (host_flags & SIL_FLAG_RERR_ON_DMA_ACT) {
+		int cnt;
+
+		for (i = 0, cnt = 0; i < n_ports; i++) {
+			tmp = readl(mmio_base + sil_port[i].sfis_cfg);
+			if ((tmp & 0x3) != 0x01)
+				continue;
+			if (!cnt)
+				dev_printk(KERN_INFO, &pdev->dev,
+					   "Applying R_ERR on DMA activate "
+					   "FIS errata fix\n");
+			writel(tmp & ~0x3, mmio_base + sil_port[i].sfis_cfg);
+			cnt++;
+		}
+	}
+
+	if (n_ports == 4) {
+		/* flip the magic "make 4 ports work" bit */
+		tmp = readl(mmio_base + sil_port[2].bmdma);
+		if ((tmp & SIL_INTR_STEERING) == 0)
+			writel(tmp | SIL_INTR_STEERING,
+			       mmio_base + sil_port[2].bmdma);
+	}
+}
+
 static int sil_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 {
 	static int printed_version;
@@ -570,8 +621,6 @@ static int sil_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 	int rc;
 	unsigned int i;
 	int pci_dev_busy = 0;
-	u32 tmp;
-	u8 cls;
 
 	if (!printed_version++)
 		dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
@@ -630,42 +679,8 @@ static int sil_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 		ata_std_ports(&probe_ent->port[i]);
 	}
 
-	/* Initialize FIFO PCI bus arbitration */
-	cls = sil_get_device_cache_line(pdev);
-	if (cls) {
-		cls >>= 3;
-		cls++;  /* cls = (line_size/8)+1 */
-		for (i = 0; i < probe_ent->n_ports; i++)
-			writew(cls << 8 | cls,
-			       mmio_base + sil_port[i].fifo_cfg);
-	} else
-		dev_printk(KERN_WARNING, &pdev->dev,
-			   "cache line size not set.  Driver may not function\n");
-
-	/* Apply R_ERR on DMA activate FIS errata workaround */
-	if (probe_ent->host_flags & SIL_FLAG_RERR_ON_DMA_ACT) {
-		int cnt;
-
-		for (i = 0, cnt = 0; i < probe_ent->n_ports; i++) {
-			tmp = readl(mmio_base + sil_port[i].sfis_cfg);
-			if ((tmp & 0x3) != 0x01)
-				continue;
-			if (!cnt)
-				dev_printk(KERN_INFO, &pdev->dev,
-					   "Applying R_ERR on DMA activate "
-					   "FIS errata fix\n");
-			writel(tmp & ~0x3, mmio_base + sil_port[i].sfis_cfg);
-			cnt++;
-		}
-	}
-
-	if (ent->driver_data == sil_3114) {
-		/* flip the magic "make 4 ports work" bit */
-		tmp = readl(mmio_base + sil_port[2].bmdma);
-		if ((tmp & SIL_INTR_STEERING) == 0)
-			writel(tmp | SIL_INTR_STEERING,
-			       mmio_base + sil_port[2].bmdma);
-	}
+	sil_init_controller(pdev, probe_ent->n_ports, probe_ent->host_flags,
+			    mmio_base);
 
 	pci_set_master(pdev);
 
@@ -685,6 +700,18 @@ static int sil_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 	return rc;
 }
 
+static int sil_pci_device_resume(struct pci_dev *pdev)
+{
+	struct ata_host_set *host_set = dev_get_drvdata(&pdev->dev);
+
+	ata_pci_device_do_resume(pdev);
+	sil_init_controller(pdev, host_set->n_ports, host_set->ports[0]->flags,
+			    host_set->mmio_base);
+	ata_host_set_resume(host_set);
+
+	return 0;
+}
+
 static int __init sil_init(void)
 {
 	return pci_module_init(&sil_pci_driver);

drivers/scsi/sata_sil24.c

@@ -92,6 +92,7 @@ enum {
 	HOST_CTRL_STOP		= (1 << 18), /* latched PCI STOP */
 	HOST_CTRL_DEVSEL	= (1 << 19), /* latched PCI DEVSEL */
 	HOST_CTRL_REQ64		= (1 << 20), /* latched PCI REQ64 */
+	HOST_CTRL_GLOBAL_RST	= (1 << 31), /* global reset */
 
 	/*
 	 * Port registers
@@ -338,6 +339,7 @@ static int sil24_port_start(struct ata_port *ap);
 static void sil24_port_stop(struct ata_port *ap);
 static void sil24_host_stop(struct ata_host_set *host_set);
 static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
+static int sil24_pci_device_resume(struct pci_dev *pdev);
 
 static const struct pci_device_id sil24_pci_tbl[] = {
 	{ 0x1095, 0x3124, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BID_SIL3124 },
@@ -353,6 +355,8 @@ static struct pci_driver sil24_pci_driver = {
 	.id_table		= sil24_pci_tbl,
 	.probe			= sil24_init_one,
 	.remove			= ata_pci_remove_one, /* safe? */
+	.suspend		= ata_pci_device_suspend,
+	.resume			= sil24_pci_device_resume,
 };
 
 static struct scsi_host_template sil24_sht = {
@@ -372,6 +376,8 @@ static struct scsi_host_template sil24_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.suspend		= ata_scsi_device_suspend,
+	.resume			= ata_scsi_device_resume,
 };
 
 static const struct ata_port_operations sil24_ops = {
@@ -607,7 +613,7 @@ static int sil24_hardreset(struct ata_port *ap, unsigned int *class)
 	/* SStatus oscillates between zero and valid status after
 	 * DEV_RST, debounce it.
 	 */
-	rc = sata_phy_debounce(ap, sata_deb_timing_before_fsrst);
+	rc = sata_phy_debounce(ap, sata_deb_timing_long);
 	if (rc) {
 		reason = "PHY debouncing failed";
 		goto err;
@@ -988,6 +994,64 @@ static void sil24_host_stop(struct ata_host_set *host_set)
 	kfree(hpriv);
 }
 
+static void sil24_init_controller(struct pci_dev *pdev, int n_ports,
+				  unsigned long host_flags,
+				  void __iomem *host_base,
+				  void __iomem *port_base)
+{
+	u32 tmp;
+	int i;
+
+	/* GPIO off */
+	writel(0, host_base + HOST_FLASH_CMD);
+
+	/* clear global reset & mask interrupts during initialization */
+	writel(0, host_base + HOST_CTRL);
+
+	/* init ports */
+	for (i = 0; i < n_ports; i++) {
+		void __iomem *port = port_base + i * PORT_REGS_SIZE;
+
+		/* Initial PHY setting */
+		writel(0x20c, port + PORT_PHY_CFG);
+
+		/* Clear port RST */
+		tmp = readl(port + PORT_CTRL_STAT);
+		if (tmp & PORT_CS_PORT_RST) {
+			writel(PORT_CS_PORT_RST, port + PORT_CTRL_CLR);
+			tmp = ata_wait_register(port + PORT_CTRL_STAT,
+						PORT_CS_PORT_RST,
+						PORT_CS_PORT_RST, 10, 100);
+			if (tmp & PORT_CS_PORT_RST)
+				dev_printk(KERN_ERR, &pdev->dev,
+				           "failed to clear port RST\n");
+		}
+
+		/* Configure IRQ WoC */
+		if (host_flags & SIL24_FLAG_PCIX_IRQ_WOC)
+			writel(PORT_CS_IRQ_WOC, port + PORT_CTRL_STAT);
+		else
+			writel(PORT_CS_IRQ_WOC, port + PORT_CTRL_CLR);
+
+		/* Zero error counters. */
+		writel(0x8000, port + PORT_DECODE_ERR_THRESH);
+		writel(0x8000, port + PORT_CRC_ERR_THRESH);
+		writel(0x8000, port + PORT_HSHK_ERR_THRESH);
+		writel(0x0000, port + PORT_DECODE_ERR_CNT);
+		writel(0x0000, port + PORT_CRC_ERR_CNT);
+		writel(0x0000, port + PORT_HSHK_ERR_CNT);
+
+		/* Always use 64bit activation */
+		writel(PORT_CS_32BIT_ACTV, port + PORT_CTRL_CLR);
+
+		/* Clear port multiplier enable and resume bits */
+		writel(PORT_CS_PM_EN | PORT_CS_RESUME, port + PORT_CTRL_CLR);
+	}
+
+	/* Turn on interrupts */
+	writel(IRQ_STAT_4PORTS, host_base + HOST_CTRL);
+}
+
 static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 {
 	static int printed_version = 0;
@@ -1076,9 +1140,6 @@ static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 		}
 	}
 
-	/* GPIO off */
-	writel(0, host_base + HOST_FLASH_CMD);
-
 	/* Apply workaround for completion IRQ loss on PCI-X errata */
 	if (probe_ent->host_flags & SIL24_FLAG_PCIX_IRQ_WOC) {
 		tmp = readl(host_base + HOST_CTRL);
@@ -1090,56 +1151,18 @@ static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 			probe_ent->host_flags &= ~SIL24_FLAG_PCIX_IRQ_WOC;
 	}
 
-	/* clear global reset & mask interrupts during initialization */
-	writel(0, host_base + HOST_CTRL);
-
 	for (i = 0; i < probe_ent->n_ports; i++) {
-		void __iomem *port = port_base + i * PORT_REGS_SIZE;
-		unsigned long portu = (unsigned long)port;
+		unsigned long portu =
+			(unsigned long)port_base + i * PORT_REGS_SIZE;
 
 		probe_ent->port[i].cmd_addr = portu;
 		probe_ent->port[i].scr_addr = portu + PORT_SCONTROL;
 
 		ata_std_ports(&probe_ent->port[i]);
-
-		/* Initial PHY setting */
-		writel(0x20c, port + PORT_PHY_CFG);
-
-		/* Clear port RST */
-		tmp = readl(port + PORT_CTRL_STAT);
-		if (tmp & PORT_CS_PORT_RST) {
-			writel(PORT_CS_PORT_RST, port + PORT_CTRL_CLR);
-			tmp = ata_wait_register(port + PORT_CTRL_STAT,
-						PORT_CS_PORT_RST,
-						PORT_CS_PORT_RST, 10, 100);
-			if (tmp & PORT_CS_PORT_RST)
-				dev_printk(KERN_ERR, &pdev->dev,
-				           "failed to clear port RST\n");
-		}
-
-		/* Configure IRQ WoC */
-		if (probe_ent->host_flags & SIL24_FLAG_PCIX_IRQ_WOC)
-			writel(PORT_CS_IRQ_WOC, port + PORT_CTRL_STAT);
-		else
-			writel(PORT_CS_IRQ_WOC, port + PORT_CTRL_CLR);
-
-		/* Zero error counters. */
-		writel(0x8000, port + PORT_DECODE_ERR_THRESH);
-		writel(0x8000, port + PORT_CRC_ERR_THRESH);
-		writel(0x8000, port + PORT_HSHK_ERR_THRESH);
-		writel(0x0000, port + PORT_DECODE_ERR_CNT);
-		writel(0x0000, port + PORT_CRC_ERR_CNT);
-		writel(0x0000, port + PORT_HSHK_ERR_CNT);
-
-		/* Always use 64bit activation */
-		writel(PORT_CS_32BIT_ACTV, port + PORT_CTRL_CLR);
-
-		/* Clear port multiplier enable and resume bits */
-		writel(PORT_CS_PM_EN | PORT_CS_RESUME, port + PORT_CTRL_CLR);
 	}
 
-	/* Turn on interrupts */
-	writel(IRQ_STAT_4PORTS, host_base + HOST_CTRL);
+	sil24_init_controller(pdev, probe_ent->n_ports, probe_ent->host_flags,
+			      host_base, port_base);
 
 	pci_set_master(pdev);
 
@@ -1162,6 +1185,25 @@ static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 	return rc;
 }
 
+static int sil24_pci_device_resume(struct pci_dev *pdev)
+{
+	struct ata_host_set *host_set = dev_get_drvdata(&pdev->dev);
+	struct sil24_host_priv *hpriv = host_set->private_data;
+
+	ata_pci_device_do_resume(pdev);
+
+	if (pdev->dev.power.power_state.event == PM_EVENT_SUSPEND)
+		writel(HOST_CTRL_GLOBAL_RST, hpriv->host_base + HOST_CTRL);
+
+	sil24_init_controller(pdev, host_set->n_ports,
+			      host_set->ports[0]->flags,
+			      hpriv->host_base, hpriv->port_base);
+
+	ata_host_set_resume(host_set);
+
+	return 0;
+}
+
 static int __init sil24_init(void)
 {
 	return pci_module_init(&sil24_pci_driver);

drivers/scsi/sata_vsc.c

@@ -297,7 +297,7 @@ static const struct ata_port_operations vsc_sata_ops = {
 	.bmdma_status		= ata_bmdma_status,
 	.qc_prep		= ata_qc_prep,
 	.qc_issue		= ata_qc_issue_prot,
-	.data_xfer		= ata_pio_data_xfer,
+	.data_xfer		= ata_mmio_data_xfer,
 	.freeze			= ata_bmdma_freeze,
 	.thaw			= ata_bmdma_thaw,
 	.error_handler		= ata_bmdma_error_handler,

include/linux/libata.h

@@ -131,6 +131,7 @@ enum {
 	ATA_DFLAG_CFG_MASK	= (1 << 8) - 1,
 
 	ATA_DFLAG_PIO		= (1 << 8), /* device currently in PIO mode */
+	ATA_DFLAG_SUSPENDED	= (1 << 9), /* device suspended */
 	ATA_DFLAG_INIT_MASK	= (1 << 16) - 1,
 
 	ATA_DFLAG_DETACH	= (1 << 16),
@@ -160,22 +161,28 @@ enum {
 	ATA_FLAG_HRST_TO_RESUME	= (1 << 11), /* hardreset to resume phy */
 	ATA_FLAG_SKIP_D2H_BSY	= (1 << 12), /* can't wait for the first D2H
 					      * Register FIS clearing BSY */
-
 	ATA_FLAG_DEBUGMSG	= (1 << 13),
-	ATA_FLAG_FLUSH_PORT_TASK = (1 << 14), /* flush port task */
 
-	ATA_FLAG_EH_PENDING	= (1 << 15), /* EH pending */
-	ATA_FLAG_EH_IN_PROGRESS	= (1 << 16), /* EH in progress */
-	ATA_FLAG_FROZEN		= (1 << 17), /* port is frozen */
-	ATA_FLAG_RECOVERED	= (1 << 18), /* recovery action performed */
-	ATA_FLAG_LOADING	= (1 << 19), /* boot/loading probe */
-	ATA_FLAG_UNLOADING	= (1 << 20), /* module is unloading */
-	ATA_FLAG_SCSI_HOTPLUG	= (1 << 21), /* SCSI hotplug scheduled */
+	/* The following flag belongs to ap->pflags but is kept in
+	 * ap->flags because it's referenced in many LLDs and will be
+	 * removed in not-too-distant future.
+	 */
+	ATA_FLAG_DISABLED	= (1 << 23), /* port is disabled, ignore it */
+
+	/* bits 24:31 of ap->flags are reserved for LLD specific flags */
 
-	ATA_FLAG_DISABLED	= (1 << 22), /* port is disabled, ignore it */
-	ATA_FLAG_SUSPENDED	= (1 << 23), /* port is suspended (power) */
+	/* struct ata_port pflags */
+	ATA_PFLAG_EH_PENDING	= (1 << 0), /* EH pending */
+	ATA_PFLAG_EH_IN_PROGRESS = (1 << 1), /* EH in progress */
+	ATA_PFLAG_FROZEN	= (1 << 2), /* port is frozen */
+	ATA_PFLAG_RECOVERED	= (1 << 3), /* recovery action performed */
+	ATA_PFLAG_LOADING	= (1 << 4), /* boot/loading probe */
+	ATA_PFLAG_UNLOADING	= (1 << 5), /* module is unloading */
+	ATA_PFLAG_SCSI_HOTPLUG	= (1 << 6), /* SCSI hotplug scheduled */
 
-	/* bits 24:31 of ap->flags are reserved for LLDD specific flags */
+	ATA_PFLAG_FLUSH_PORT_TASK = (1 << 16), /* flush port task */
+	ATA_PFLAG_SUSPENDED	= (1 << 17), /* port is suspended (power) */
+	ATA_PFLAG_PM_PENDING	= (1 << 18), /* PM operation pending */
 
 	/* struct ata_queued_cmd flags */
 	ATA_QCFLAG_ACTIVE	= (1 << 0), /* cmd not yet ack'd to scsi lyer */
@@ -248,12 +255,19 @@ enum {
 	ATA_EH_REVALIDATE	= (1 << 0),
 	ATA_EH_SOFTRESET	= (1 << 1),
 	ATA_EH_HARDRESET	= (1 << 2),
+	ATA_EH_SUSPEND		= (1 << 3),
+	ATA_EH_RESUME		= (1 << 4),
+	ATA_EH_PM_FREEZE	= (1 << 5),
 
 	ATA_EH_RESET_MASK	= ATA_EH_SOFTRESET | ATA_EH_HARDRESET,
-	ATA_EH_PERDEV_MASK	= ATA_EH_REVALIDATE,
+	ATA_EH_PERDEV_MASK	= ATA_EH_REVALIDATE | ATA_EH_SUSPEND |
+				  ATA_EH_RESUME | ATA_EH_PM_FREEZE,
 
 	/* ata_eh_info->flags */
 	ATA_EHI_HOTPLUGGED	= (1 << 0),  /* could have been hotplugged */
+	ATA_EHI_RESUME_LINK	= (1 << 1),  /* need to resume link */
+	ATA_EHI_NO_AUTOPSY	= (1 << 2),  /* no autopsy */
+	ATA_EHI_QUIET		= (1 << 3),  /* be quiet */
 
 	ATA_EHI_DID_RESET	= (1 << 16), /* already reset this port */
 
@@ -486,6 +500,7 @@ struct ata_port {
 	const struct ata_port_operations *ops;
 	spinlock_t		*lock;
 	unsigned long		flags;	/* ATA_FLAG_xxx */
+	unsigned int		pflags; /* ATA_PFLAG_xxx */
 	unsigned int		id;	/* unique id req'd by scsi midlyr */
 	unsigned int		port_no; /* unique port #; from zero */
 	unsigned int		hard_port_no;	/* hardware port #; from zero */
@@ -535,6 +550,9 @@ struct ata_port {
 	struct list_head	eh_done_q;
 	wait_queue_head_t	eh_wait_q;
 
+	pm_message_t		pm_mesg;
+	int			*pm_result;
+
 	void			*private_data;
 
 	u8			sector_buf[ATA_SECT_SIZE]; /* owned by EH */
@@ -589,6 +607,9 @@ struct ata_port_operations {
 	void (*scr_write) (struct ata_port *ap, unsigned int sc_reg,
 			   u32 val);
 
+	int (*port_suspend) (struct ata_port *ap, pm_message_t mesg);
+	int (*port_resume) (struct ata_port *ap);
+
 	int (*port_start) (struct ata_port *ap);
 	void (*port_stop) (struct ata_port *ap);
 
@@ -622,9 +643,18 @@ struct ata_timing {
 
 #define FIT(v,vmin,vmax)	max_t(short,min_t(short,v,vmax),vmin)
 
-extern const unsigned long sata_deb_timing_boot[];
-extern const unsigned long sata_deb_timing_eh[];
-extern const unsigned long sata_deb_timing_before_fsrst[];
+extern const unsigned long sata_deb_timing_normal[];
+extern const unsigned long sata_deb_timing_hotplug[];
+extern const unsigned long sata_deb_timing_long[];
+
+static inline const unsigned long *
+sata_ehc_deb_timing(struct ata_eh_context *ehc)
+{
+	if (ehc->i.flags & ATA_EHI_HOTPLUGGED)
+		return sata_deb_timing_hotplug;
+	else
+		return sata_deb_timing_normal;
+}
 
 extern void ata_port_probe(struct ata_port *);
 extern void __sata_phy_reset(struct ata_port *ap);
@@ -644,6 +674,8 @@ extern void ata_std_ports(struct ata_ioports *ioaddr);
 extern int ata_pci_init_one (struct pci_dev *pdev, struct ata_port_info **port_info,
 			     unsigned int n_ports);
 extern void ata_pci_remove_one (struct pci_dev *pdev);
+extern void ata_pci_device_do_suspend(struct pci_dev *pdev, pm_message_t state);
+extern void ata_pci_device_do_resume(struct pci_dev *pdev);
 extern int ata_pci_device_suspend(struct pci_dev *pdev, pm_message_t state);
 extern int ata_pci_device_resume(struct pci_dev *pdev);
 extern int ata_pci_clear_simplex(struct pci_dev *pdev);
@@ -664,8 +696,9 @@ extern int ata_port_online(struct ata_port *ap);
 extern int ata_port_offline(struct ata_port *ap);
 extern int ata_scsi_device_resume(struct scsi_device *);
 extern int ata_scsi_device_suspend(struct scsi_device *, pm_message_t state);
-extern int ata_device_resume(struct ata_device *);
-extern int ata_device_suspend(struct ata_device *, pm_message_t state);
+extern int ata_host_set_suspend(struct ata_host_set *host_set,
+				pm_message_t mesg);
+extern void ata_host_set_resume(struct ata_host_set *host_set);
 extern int ata_ratelimit(void);
 extern unsigned int ata_busy_sleep(struct ata_port *ap,
 				   unsigned long timeout_pat,
@@ -825,19 +858,24 @@ extern void ata_do_eh(struct ata_port *ap, ata_prereset_fn_t prereset,
 	(ehi)->desc_len = 0; \
 } while (0)
 
-static inline void ata_ehi_hotplugged(struct ata_eh_info *ehi)
+static inline void __ata_ehi_hotplugged(struct ata_eh_info *ehi)
 {
 	if (ehi->flags & ATA_EHI_HOTPLUGGED)
 		return;
 
-	ehi->flags |= ATA_EHI_HOTPLUGGED;
+	ehi->flags |= ATA_EHI_HOTPLUGGED | ATA_EHI_RESUME_LINK;
 	ehi->hotplug_timestamp = jiffies;
 
-	ehi->err_mask |= AC_ERR_ATA_BUS;
 	ehi->action |= ATA_EH_SOFTRESET;
 	ehi->probe_mask |= (1 << ATA_MAX_DEVICES) - 1;
 }
 
+static inline void ata_ehi_hotplugged(struct ata_eh_info *ehi)
+{
+	__ata_ehi_hotplugged(ehi);
+	ehi->err_mask |= AC_ERR_ATA_BUS;
+}
+
 /*
  * qc helpers
  */
@@ -921,6 +959,11 @@ static inline unsigned int ata_dev_absent(const struct ata_device *dev)
 	return ata_class_absent(dev->class);
 }
 
+static inline unsigned int ata_dev_ready(const struct ata_device *dev)
+{
+	return ata_dev_enabled(dev) && !(dev->flags & ATA_DFLAG_SUSPENDED);
+}
+
 /*
  * port helpers
  */

include/linux/pci_ids.h

@@ -2019,6 +2019,13 @@
 #define PCI_VENDOR_ID_TDI               0x192E
 #define PCI_DEVICE_ID_TDI_EHCI          0x0101
 
+#define PCI_VENDOR_ID_JMICRON		0x197B
+#define PCI_DEVICE_ID_JMICRON_JMB360	0x2360
+#define PCI_DEVICE_ID_JMICRON_JMB361	0x2361
+#define PCI_DEVICE_ID_JMICRON_JMB363	0x2363
+#define PCI_DEVICE_ID_JMICRON_JMB365	0x2365
+#define PCI_DEVICE_ID_JMICRON_JMB366	0x2366
+#define PCI_DEVICE_ID_JMICRON_JMB368	0x2368
 
 #define PCI_VENDOR_ID_TEKRAM		0x1de1
 #define PCI_DEVICE_ID_TEKRAM_DC290	0xdc29