EtherExpress16: fix printing timed out status

in drivers/net/eexpress.c:558, function unstick_cu()

while (!SCB_complete(rsst=scb_status(dev))) {
	...
	if (...)
		printk(KERN_WARNING "%s: Reset timed out status %04x, retrying...\n",
                                                       dev->name,rsst);
}

but this will become 

while (!((rsst = scb_status(dev) & 0x8000) != 0) ...

because of the macro:

#define SCB_complete(s) ((s&0x8000)!=0)

so rsst can only become either 0x8000 or 0, but in the latter case the
loop ends, I think the wrong timed out status is printed. This also
cleans up similar macros.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/eexpress.h

@@ -68,17 +68,17 @@
  */
 
 /* these functions take the SCB status word and test the relevant status bit */
-#define SCB_complete(s) ((s&0x8000)!=0)
-#define SCB_rxdframe(s) ((s&0x4000)!=0)
-#define SCB_CUdead(s)   ((s&0x2000)!=0)
-#define SCB_RUdead(s)   ((s&0x1000)!=0)
-#define SCB_ack(s)      (s & 0xf000)
+#define SCB_complete(s) (((s) & 0x8000) != 0)
+#define SCB_rxdframe(s) (((s) & 0x4000) != 0)
+#define SCB_CUdead(s)   (((s) & 0x2000) != 0)
+#define SCB_RUdead(s)   (((s) & 0x1000) != 0)
+#define SCB_ack(s)      ((s) & 0xf000)
 
 /* Command unit status: 0=idle, 1=suspended, 2=active */
-#define SCB_CUstat(s)   ((s&0x0300)>>8)
+#define SCB_CUstat(s)   (((s)&0x0300)>>8)
 
 /* Receive unit status: 0=idle, 1=suspended, 2=out of resources, 4=ready */
-#define SCB_RUstat(s)   ((s&0x0070)>>4)
+#define SCB_RUstat(s)   (((s)&0x0070)>>4)
 
 /* SCB commands */
 #define SCB_CUnop       0x0000
@@ -98,18 +98,18 @@
  * Command block defines
  */
 
-#define Stat_Done(s)    ((s&0x8000)!=0)
-#define Stat_Busy(s)    ((s&0x4000)!=0)
-#define Stat_OK(s)      ((s&0x2000)!=0)
-#define Stat_Abort(s)   ((s&0x1000)!=0)
-#define Stat_STFail     ((s&0x0800)!=0)
-#define Stat_TNoCar(s)  ((s&0x0400)!=0)
-#define Stat_TNoCTS(s)  ((s&0x0200)!=0)
-#define Stat_TNoDMA(s)  ((s&0x0100)!=0)
-#define Stat_TDefer(s)  ((s&0x0080)!=0)
-#define Stat_TColl(s)   ((s&0x0040)!=0)
-#define Stat_TXColl(s)  ((s&0x0020)!=0)
-#define Stat_NoColl(s)  (s&0x000f)
+#define Stat_Done(s)    (((s) & 0x8000) != 0)
+#define Stat_Busy(s)    (((s) & 0x4000) != 0)
+#define Stat_OK(s)      (((s) & 0x2000) != 0)
+#define Stat_Abort(s)   (((s) & 0x1000) != 0)
+#define Stat_STFail     (((s) & 0x0800) != 0)
+#define Stat_TNoCar(s)  (((s) & 0x0400) != 0)
+#define Stat_TNoCTS(s)  (((s) & 0x0200) != 0)
+#define Stat_TNoDMA(s)  (((s) & 0x0100) != 0)
+#define Stat_TDefer(s)  (((s) & 0x0080) != 0)
+#define Stat_TColl(s)   (((s) & 0x0040) != 0)
+#define Stat_TXColl(s)  (((s) & 0x0020) != 0)
+#define Stat_NoColl(s)  ((s) & 0x000f)
 
 /* Cmd_END will end AFTER the command if this is the first
  * command block after an SCB_CUstart, but BEFORE the command
@@ -136,16 +136,16 @@
  * Frame Descriptor (Receive block) defines
  */
 
-#define FD_Done(s)  ((s&0x8000)!=0)
-#define FD_Busy(s)  ((s&0x4000)!=0)
-#define FD_OK(s)    ((s&0x2000)!=0)
+#define FD_Done(s)  (((s) & 0x8000) != 0)
+#define FD_Busy(s)  (((s) & 0x4000) != 0)
+#define FD_OK(s)    (((s) & 0x2000) != 0)
 
-#define FD_CRC(s)   ((s&0x0800)!=0)
-#define FD_Align(s) ((s&0x0400)!=0)
-#define FD_Resrc(s) ((s&0x0200)!=0)
-#define FD_DMA(s)   ((s&0x0100)!=0)
-#define FD_Short(s) ((s&0x0080)!=0)
-#define FD_NoEOF(s) ((s&0x0040)!=0)
+#define FD_CRC(s)   (((s) & 0x0800) != 0)
+#define FD_Align(s) (((s) & 0x0400) != 0)
+#define FD_Resrc(s) (((s) & 0x0200) != 0)
+#define FD_DMA(s)   (((s) & 0x0100) != 0)
+#define FD_Short(s) (((s) & 0x0080) != 0)
+#define FD_NoEOF(s) (((s) & 0x0040) != 0)
 
 struct rfd_header {
 	volatile unsigned long flags;