Merge tag 'sunxi-h3-h5-for-4.21' of...

Merge tag 'sunxi-h3-h5-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Allwinner H3/H5 changes for 4.21

Our usual pull request with the changes shared between the H3 and H5 SoCs.

The major changes for this release are:
  - Addition of the video engine for the H5
  - H3 Camera support
  - New board: Emlid Neutis N5, Mapleboard MP130

* tag 'sunxi-h3-h5-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  arm64: dts: allwinner: h5: Add Video Engine node
  ARM/arm64: dts: allwinner: Move H3/H5 syscon label over to soc-specific nodes
  arm64: dts: allwinner: h5: Add system-control node with SRAM C1
  ARM: dts: sun8i: h3: Fix the system-control register range
  ARM: dts: sun8i: Add the H3/H5 CSI controller
  ARM: dts: sun8i-h3: Add dts for the Mapleboard MP130
  arm64: dts: allwinner: new board - Emlid Neutis N5
  dt-bindings: vendor-prefix: new vendor - Emlid
  ARM: dts: sun8i-h3: add sy8106a to orange pi plus
Signed-off-by: Olof Johansson <olof@lixom.net>

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -113,6 +113,7 @@ edt	Emerging Display Technologies
 eeti	eGalax_eMPIA Technology Inc
 elan	Elan Microelectronic Corp.
 embest	Shenzhen Embest Technology Co., Ltd.
+emlid	Emlid, Ltd.
 emmicro	EM Microelectronic
 emtrion	emtrion GmbH
 endless	Endless Mobile, Inc.

arch/arm/boot/dts/Makefile

@@ -1062,6 +1062,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-h3-bananapi-m2-plus-v1.2.dtb \
 	sun8i-h3-beelink-x2.dtb \
 	sun8i-h3-libretech-all-h3-cc.dtb \
+	sun8i-h3-mapleboard-mp130.dtb \
 	sun8i-h3-nanopi-m1.dtb	\
 	sun8i-h3-nanopi-m1-plus.dtb \
 	sun8i-h3-nanopi-neo.dtb \

arch/arm/boot/dts/sun8i-h3-mapleboard-mp130.dts

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 Centrum Embedded Systems, Jia-Bin Huang <jb@ces.com.tw>
+ * Copyright (C) 2018 Jonathan McDowell <noodles@earth.li>
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "MapleBoard MP130";
+	compatible = "mapleboard,mp130", "allwinner,sun8i-h3";
+
+	aliases {
+		ethernet0 = &emac;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pwr_led {
+			label = "mp130:orange:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		status_led {
+			label = "mp130:orange:status";
+			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	r_gpio_keys {
+		compatible = "gpio-keys";
+
+		power {
+			label = "power";
+			linux,code = <KEY_POWER>;
+			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
+		};
+
+		user {
+			label = "user";
+			linux,code = <BTN_0>;
+			gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"LINEIN", "Line In";
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+&ir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ir_pins_a>;
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	cd-inverted;
+	status = "okay";
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "disabled";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	status = "disabled";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	/* USB VBUS is always on */
+	status = "okay";
+};

arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts

@@ -74,6 +74,10 @@ reg_usb3_vbus: usb3-vbus {
 	};
 };
 
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
 &ehci3 {
 	status = "okay";
 };
@@ -119,6 +123,22 @@ usb3_vbus_pin_a: usb3_vbus_pin {
 	};
 };
 
+&r_i2c {
+	status = "okay";
+
+	reg_vdd_cpux: regulator@65 {
+		compatible = "silergy,sy8106a";
+		reg = <0x65>;
+		regulator-name = "vdd-cpux";
+		silergy,fixed-microvolt = <1200000>;
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1400000>;
+		regulator-ramp-delay = <200>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
 &usbphy {
 	usb3_vbus-supply = <&reg_usb3_vbus>;
 };

arch/arm/boot/dts/sun8i-h3.dtsi

@@ -120,9 +120,9 @@ timer {
 	};
 
 	soc {
-		system-control@1c00000 {
+		syscon: system-control@1c00000 {
 			compatible = "allwinner,sun8i-h3-system-control";
-			reg = <0x01c00000 0x30>;
+			reg = <0x01c00000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;

arch/arm/boot/dts/sunxi-h3-h5.dtsi

@@ -146,12 +146,6 @@ mixer0_out_tcon0: endpoint {
 			};
 		};
 
-		syscon: syscon@1c00000 {
-			compatible = "allwinner,sun8i-h3-system-controller",
-				"syscon";
-			reg = <0x01c00000 0x1000>;
-		};
-
 		dma: dma-controller@1c02000 {
 			compatible = "allwinner,sun8i-h3-dma";
 			reg = <0x01c02000 0x1000>;
@@ -387,6 +381,13 @@ pio: pinctrl@1c20800 {
 			interrupt-controller;
 			#interrupt-cells = <3>;
 
+			csi_pins: csi {
+				pins = "PE0", "PE2", "PE3", "PE4", "PE5",
+				       "PE6", "PE7", "PE8", "PE9", "PE10",
+				       "PE11";
+				function = "csi";
+			};
+
 			emac_rgmii_pins: emac0 {
 				pins = "PD0", "PD1", "PD2", "PD3", "PD4",
 				       "PD5", "PD7", "PD8", "PD9", "PD10",
@@ -738,6 +739,21 @@ gic: interrupt-controller@1c81000 {
 			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
 		};
 
+		csi: camera@1cb0000 {
+			compatible = "allwinner,sun8i-h3-csi",
+				     "allwinner,sun6i-a31-csi";
+			reg = <0x01cb0000 0x1000>;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CSI>,
+				 <&ccu CLK_CSI_SCLK>,
+				 <&ccu CLK_DRAM_CSI>;
+			clock-names = "bus", "mod", "ram";
+			resets = <&ccu RST_BUS_CSI>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&csi_pins>;
+			status = "disabled";
+		};
+
 		hdmi: hdmi@1ee0000 {
 			compatible = "allwinner,sun8i-h3-dw-hdmi",
 				     "allwinner,sun8i-a83t-dw-hdmi";

arch/arm64/boot/dts/allwinner/Makefile

@@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus-v1.2.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-emlid-neutis-n5-devboard.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-libretech-all-h3-cc.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo2.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo-plus2.dtb

arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5-devboard.dts

+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * DTS for Emlid Neutis N5 Dev board.
+ *
+ * Copyright (C) 2018 Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
+ */
+
+/dts-v1/;
+
+#include "sun50i-h5-emlid-neutis-n5.dtsi"
+
+/ {
+	model = "Emlid Neutis N5 Developer board";
+	compatible = "emlid,neutis-n5-devboard",
+		     "emlid,neutis-n5",
+		     "allwinner,sun50i-h5";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	reg_usb0_vbus: usb0-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb0-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>;   /* PL9 */
+		status = "okay";
+	};
+
+	vdd_cpux: gpio-regulator {
+		compatible = "regulator-gpio";
+		pinctrl-names = "default";
+		regulator-name = "vdd-cpux";
+		regulator-type = "voltage";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-ramp-delay = <50>; /* 4ms */
+		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+		gpios-states = <0x1>;
+		states = <1100000 0x0
+			  1300000 0x1>;
+	};
+};
+
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"LINEIN", "Line In",
+		"MIC1", "Mic",
+		"MIC2", "Mic",
+		"Mic",  "MBIAS";
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	status = "okay";
+};

arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5.dtsi

+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * DTSI for Emlid Neutis N5 SoM.
+ *
+ * Copyright (C) 2018 Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
+ */
+
+/dts-v1/;
+
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	reg_vcc3v3: vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		reset-gpios = <&pio 2 7 GPIO_ACTIVE_LOW>; /* PC7 */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 5 IRQ_TYPE_LEVEL_LOW>;	/* PL5 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	status = "okay";
+};

arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi

@@ -94,6 +94,39 @@ timer {
 	};
 
 	soc {
+		syscon: system-control@1c00000 {
+			compatible = "allwinner,sun50i-h5-system-control";
+			reg = <0x01c00000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			sram_c1: sram@18000 {
+				compatible = "mmio-sram";
+				reg = <0x00018000 0x1c000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x00018000 0x1c000>;
+
+				ve_sram: sram-section@0 {
+					compatible = "allwinner,sun50i-h5-sram-c1",
+						     "allwinner,sun4i-a10-sram-c1";
+					reg = <0x000000 0x1c000>;
+				};
+			};
+		};
+
+		video-codec@1c0e000 {
+			compatible = "allwinner,sun50i-h5-video-engine";
+			reg = <0x01c0e000 0x1000>;
+			clocks = <&ccu CLK_BUS_VE>, <&ccu CLK_VE>,
+				 <&ccu CLK_DRAM_VE>;
+			clock-names = "ahb", "mod", "ram";
+			resets = <&ccu RST_BUS_VE>;
+			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+			allwinner,sram = <&ve_sram 1>;
+		};
+
 		mali: gpu@1e80000 {
 			compatible = "allwinner,sun50i-h5-mali", "arm,mali-450";
 			reg = <0x01e80000 0x30000>;