net: stmmac: use interrupt mode INTM=1 for multi-MSI

For interrupt mode INTM=0, TX/RX transfer complete will trigger signal
not only on sbd_perch_[tx|rx]_intr_o (Transmit/Receive Per Channel) but
also on the sbd_intr_o (Common).

As for multi-MSI implementation, setting interrupt mode INTM=1 is more
efficient as each TX intr and RX intr (TI/RI) will be handled by TX/RX ISR
without the need of calling the common MAC ISR.

Updated the TX/RX NORMAL interrupts status checking process as the
NIS status bit is not asserted for any RI/TI events for INTM=1.
Signed-off-by: Wong, Vee Khee <vee.khee.wong@intel.com>
Co-developed-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c

@@ -161,6 +161,13 @@ static void dwmac4_dma_init(void __iomem *ioaddr,
 		value |= DMA_SYS_BUS_EAME;
 
 	writel(value, ioaddr + DMA_SYS_BUS_MODE);
+
+	if (dma_cfg->multi_msi_en) {
+		value = readl(ioaddr + DMA_BUS_MODE);
+		value &= ~DMA_BUS_MODE_INTM_MASK;
+		value |= (DMA_BUS_MODE_INTM_MODE1 << DMA_BUS_MODE_INTM_SHIFT);
+		writel(value, ioaddr + DMA_BUS_MODE);
+	}
 }
 
 static void _dwmac4_dump_dma_regs(void __iomem *ioaddr, u32 channel,

drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.h

@@ -25,6 +25,9 @@
 #define DMA_TBS_CTRL			0x00001050
 
 /* DMA Bus Mode bitmap */
+#define DMA_BUS_MODE_INTM_MASK		GENMASK(17, 16)
+#define DMA_BUS_MODE_INTM_SHIFT		16
+#define DMA_BUS_MODE_INTM_MODE1		0x1
 #define DMA_BUS_MODE_SFT_RESET		BIT(0)
 
 /* DMA SYS Bus Mode bitmap */

drivers/net/ethernet/stmicro/stmmac/dwmac4_lib.c

@@ -166,7 +166,7 @@ int dwmac4_dma_interrupt(void __iomem *ioaddr,
 		}
 	}
 	/* TX/RX NORMAL interrupts */
-	if (likely(intr_status & DMA_CHAN_STATUS_NIS)) {
+	if (likely(intr_status & DMA_CHAN_STATUS_NIS))
 		x->normal_irq_n++;
 	if (likely(intr_status & DMA_CHAN_STATUS_RI)) {
 		x->rx_normal_irq_n++;
@@ -179,7 +179,6 @@ int dwmac4_dma_interrupt(void __iomem *ioaddr,
 	}
 	if (unlikely(intr_status & DMA_CHAN_STATUS_ERI))
 		x->rx_early_irq++;
-	}
 
 	writel(intr_status & intr_en, ioaddr + DMA_CHAN_STATUS(chan));
 	return ret;

drivers/net/ethernet/stmicro/stmmac/stmmac_main.c

@@ -5620,6 +5620,7 @@ int stmmac_dvr_probe(struct device *device,
 	priv->plat = plat_dat;
 	priv->ioaddr = res->addr;
 	priv->dev->base_addr = (unsigned long)res->addr;
+	priv->plat->dma_cfg->multi_msi_en = priv->plat->multi_msi_en;
 
 	priv->dev->irq = res->irq;
 	priv->wol_irq = res->wol_irq;

include/linux/stmmac.h

@@ -96,6 +96,7 @@ struct stmmac_dma_cfg {
 	int mixed_burst;
 	bool aal;
 	bool eame;
+	bool multi_msi_en;
 };
 
 #define AXI_BLEN	7