Merge branch 'omap-for-linus' of...

Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (47 commits)
  OMAP clock: use debugfs_remove_recursive() for rewinding
  OMAP2/3/4 core: create omap_device layer
  OMAP: omap_hwmod: call omap_hwmod init at boot; create interconnects
  OMAP2/3/4: create omap_hwmod layer
  OMAP2/3 board-*.c files: read bootloader configuration earlier
  OMAP2/3/4 PRCM: add module IDLEST wait code
  OMAP2/3 PM: create the OMAP PM interface and add a default OMAP PM no-op layer
  OMAP3 clock: remove superfluous calls to omap2_init_clk_clkdm
  OMAP clock: associate MPU clocks with the mpu_clkdm
  OMAP3 clock: Fixed processing of bootarg 'mpurate'
  OMAP: SDRC: Add several new register definitions
  OMAP: powerdomain: Fix overflow when doing powerdomain deps lookups.
  OMAP: PM: Added suspend target state control to debugfs for OMAP3
  OMAP: PM debug: Add PRCM register dump support
  OMAP: PM debug: make powerdomains use PM-debug counters
  OMAP: PM: Add pm-debug counters
  OMAP: PM: Add closures to clkdm_for_each and pwrdm_for_each.
  OMAP: PM: Hook into PM counters
  OMAP: PM counter infrastructure.
  OMAP3: PM: fix lockdep warning caused by omap3_pm_init
  ...

Documentation/arm/OMAP/omap_pm

+
+The OMAP PM interface
+=====================
+
+This document describes the temporary OMAP PM interface.  Driver
+authors use these functions to communicate minimum latency or
+throughput constraints to the kernel power management code.
+Over time, the intention is to merge features from the OMAP PM
+interface into the Linux PM QoS code.
+
+Drivers need to express PM parameters which:
+
+- support the range of power management parameters present in the TI SRF;
+
+- separate the drivers from the underlying PM parameter
+  implementation, whether it is the TI SRF or Linux PM QoS or Linux
+  latency framework or something else;
+
+- specify PM parameters in terms of fundamental units, such as
+  latency and throughput, rather than units which are specific to OMAP
+  or to particular OMAP variants;
+
+- allow drivers which are shared with other architectures (e.g.,
+  DaVinci) to add these constraints in a way which won't affect non-OMAP
+  systems,
+
+- can be implemented immediately with minimal disruption of other
+  architectures.
+
+
+This document proposes the OMAP PM interface, including the following
+five power management functions for driver code:
+
+1. Set the maximum MPU wakeup latency:
+   (*pdata->set_max_mpu_wakeup_lat)(struct device *dev, unsigned long t)
+
+2. Set the maximum device wakeup latency:
+   (*pdata->set_max_dev_wakeup_lat)(struct device *dev, unsigned long t)
+
+3. Set the maximum system DMA transfer start latency (CORE pwrdm):
+   (*pdata->set_max_sdma_lat)(struct device *dev, long t)
+
+4. Set the minimum bus throughput needed by a device:
+   (*pdata->set_min_bus_tput)(struct device *dev, u8 agent_id, unsigned long r)
+
+5. Return the number of times the device has lost context
+   (*pdata->get_dev_context_loss_count)(struct device *dev)
+
+
+Further documentation for all OMAP PM interface functions can be
+found in arch/arm/plat-omap/include/mach/omap-pm.h.
+
+
+The OMAP PM layer is intended to be temporary
+---------------------------------------------
+
+The intention is that eventually the Linux PM QoS layer should support
+the range of power management features present in OMAP3.  As this
+happens, existing drivers using the OMAP PM interface can be modified
+to use the Linux PM QoS code; and the OMAP PM interface can disappear.
+
+
+Driver usage of the OMAP PM functions
+-------------------------------------
+
+As the 'pdata' in the above examples indicates, these functions are
+exposed to drivers through function pointers in driver .platform_data
+structures.  The function pointers are initialized by the board-*.c
+files to point to the corresponding OMAP PM functions:
+.set_max_dev_wakeup_lat will point to
+omap_pm_set_max_dev_wakeup_lat(), etc.  Other architectures which do
+not support these functions should leave these function pointers set
+to NULL.  Drivers should use the following idiom:
+
+        if (pdata->set_max_dev_wakeup_lat)
+            (*pdata->set_max_dev_wakeup_lat)(dev, t);
+
+The most common usage of these functions will probably be to specify
+the maximum time from when an interrupt occurs, to when the device
+becomes accessible.  To accomplish this, driver writers should use the
+set_max_mpu_wakeup_lat() function to to constrain the MPU wakeup
+latency, and the set_max_dev_wakeup_lat() function to constrain the
+device wakeup latency (from clk_enable() to accessibility).  For
+example,
+
+        /* Limit MPU wakeup latency */
+        if (pdata->set_max_mpu_wakeup_lat)
+            (*pdata->set_max_mpu_wakeup_lat)(dev, tc);
+
+        /* Limit device powerdomain wakeup latency */
+        if (pdata->set_max_dev_wakeup_lat)
+            (*pdata->set_max_dev_wakeup_lat)(dev, td);
+
+        /* total wakeup latency in this example: (tc + td) */
+
+The PM parameters can be overwritten by calling the function again
+with the new value.  The settings can be removed by calling the
+function with a t argument of -1 (except in the case of
+set_max_bus_tput(), which should be called with an r argument of 0).
+
+The fifth function above, omap_pm_get_dev_context_loss_count(),
+is intended as an optimization to allow drivers to determine whether the
+device has lost its internal context.  If context has been lost, the
+driver must restore its internal context before proceeding.
+
+
+Other specialized interface functions
+-------------------------------------
+
+The five functions listed above are intended to be usable by any
+device driver.  DSPBridge and CPUFreq have a few special requirements.
+DSPBridge expresses target DSP performance levels in terms of OPP IDs.
+CPUFreq expresses target MPU performance levels in terms of MPU
+frequency.  The OMAP PM interface contains functions for these
+specialized cases to convert that input information (OPPs/MPU
+frequency) into the form that the underlying power management
+implementation needs:
+
+6. (*pdata->dsp_get_opp_table)(void)
+
+7. (*pdata->dsp_set_min_opp)(u8 opp_id)
+
+8. (*pdata->dsp_get_opp)(void)
+
+9. (*pdata->cpu_get_freq_table)(void)
+
+10. (*pdata->cpu_set_freq)(unsigned long f)
+
+11. (*pdata->cpu_get_freq)(void)

arch/arm/configs/omap3_beagle_defconfig

@@ -128,6 +128,7 @@ CONFIG_DEFAULT_AS=y
 # CONFIG_DEFAULT_NOOP is not set
 CONFIG_DEFAULT_IOSCHED="anticipatory"
 CONFIG_CLASSIC_RCU=y
+CONFIG_FREEZER=y
 
 #
 # System Type
@@ -236,6 +237,7 @@ CONFIG_ARM_THUMB=y
 # CONFIG_CPU_BPREDICT_DISABLE is not set
 CONFIG_HAS_TLS_REG=y
 # CONFIG_OUTER_CACHE is not set
+CONFIG_COMMON_CLKDEV=y
 
 #
 # Bus support
@@ -317,7 +319,12 @@ CONFIG_BINFMT_MISC=y
 #
 # Power management options
 #
-# CONFIG_PM is not set
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+# CONFIG_APM_EMULATION is not set
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 CONFIG_NET=y
 
@@ -713,6 +720,7 @@ CONFIG_GPIOLIB=y
 # CONFIG_GPIO_MAX732X is not set
 # CONFIG_GPIO_PCA953X is not set
 # CONFIG_GPIO_PCF857X is not set
+CONFIG_GPIO_TWL4030=y
 
 #
 # PCI GPIO expanders:
@@ -741,6 +749,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_SM501 is not set
 # CONFIG_HTC_EGPIO is not set
 # CONFIG_HTC_PASIC3 is not set
+CONFIG_TWL4030_CORE=y
 # CONFIG_UCB1400_CORE is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_MFD_T7L66XB is not set
@@ -787,7 +796,7 @@ CONFIG_DUMMY_CONSOLE=y
 CONFIG_USB_SUPPORT=y
 CONFIG_USB_ARCH_HAS_HCD=y
 CONFIG_USB_ARCH_HAS_OHCI=y
-# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB_ARCH_HAS_EHCI=y
 CONFIG_USB=y
 # CONFIG_USB_DEBUG is not set
 # CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
@@ -798,7 +807,8 @@ CONFIG_USB=y
 CONFIG_USB_DEVICEFS=y
 CONFIG_USB_DEVICE_CLASS=y
 # CONFIG_USB_DYNAMIC_MINORS is not set
-# CONFIG_USB_OTG is not set
+CONFIG_USB_SUSPEND=y
+CONFIG_USB_OTG=y
 # CONFIG_USB_OTG_WHITELIST is not set
 # CONFIG_USB_OTG_BLACKLIST_HUB is not set
 CONFIG_USB_MON=y
@@ -806,6 +816,8 @@ CONFIG_USB_MON=y
 #
 # USB Host Controller Drivers
 #
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
 # CONFIG_USB_C67X00_HCD is not set
 # CONFIG_USB_ISP116X_HCD is not set
 # CONFIG_USB_ISP1760_HCD is not set
@@ -818,10 +830,10 @@ CONFIG_USB_MUSB_SOC=y
 #
 # OMAP 343x high speed USB support
 #
-CONFIG_USB_MUSB_HOST=y
+# CONFIG_USB_MUSB_HOST is not set
 # CONFIG_USB_MUSB_PERIPHERAL is not set
-# CONFIG_USB_MUSB_OTG is not set
-# CONFIG_USB_GADGET_MUSB_HDRC is not set
+CONFIG_USB_MUSB_OTG=y
+CONFIG_USB_GADGET_MUSB_HDRC=y
 CONFIG_USB_MUSB_HDRC_HCD=y
 # CONFIG_MUSB_PIO_ONLY is not set
 CONFIG_USB_INVENTRA_DMA=y
@@ -887,8 +899,8 @@ CONFIG_USB_GADGET_SELECTED=y
 # CONFIG_USB_GADGET_FSL_USB2 is not set
 # CONFIG_USB_GADGET_NET2280 is not set
 # CONFIG_USB_GADGET_PXA25X is not set
-CONFIG_USB_GADGET_M66592=y
-CONFIG_USB_M66592=y
+# CONFIG_USB_GADGET_M66592 is not set
+# CONFIG_USB_M66592 is not set
 # CONFIG_USB_GADGET_PXA27X is not set
 # CONFIG_USB_GADGET_GOKU is not set
 # CONFIG_USB_GADGET_LH7A40X is not set
@@ -906,6 +918,15 @@ CONFIG_USB_ETH_RNDIS=y
 # CONFIG_USB_MIDI_GADGET is not set
 # CONFIG_USB_G_PRINTER is not set
 # CONFIG_USB_CDC_COMPOSITE is not set
+
+#
+# OTG and related infrastructure
+#
+CONFIG_USB_OTG_UTILS=y
+# CONFIG_USB_GPIO_VBUS is not set
+# CONFIG_ISP1301_OMAP is not set
+CONFIG_TWL4030_USB=y
+# CONFIG_NOP_USB_XCEIV is not set
 CONFIG_MMC=y
 # CONFIG_MMC_DEBUG is not set
 # CONFIG_MMC_UNSAFE_RESUME is not set
@@ -923,6 +944,7 @@ CONFIG_MMC_BLOCK_BOUNCE=y
 #
 # CONFIG_MMC_SDHCI is not set
 # CONFIG_MMC_OMAP is not set
+CONFIG_MMC_OMAP_HS=y
 # CONFIG_MEMSTICK is not set
 # CONFIG_ACCESSIBILITY is not set
 # CONFIG_NEW_LEDS is not set
@@ -981,10 +1003,11 @@ CONFIG_RTC_INTF_DEV=y
 #
 # Voltage and Current regulators
 #
-# CONFIG_REGULATOR is not set
+CONFIG_REGULATOR=y
 # CONFIG_REGULATOR_FIXED_VOLTAGE is not set
 # CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
 # CONFIG_REGULATOR_BQ24022 is not set
+CONFIG_REGULATOR_TWL4030=y
 # CONFIG_UIO is not set
 
 #

arch/arm/configs/omap_3430sdp_defconfig

 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.29-rc8
-# Fri Mar 13 14:17:01 2009
+# Linux kernel version: 2.6.30-omap1
+# Tue Jun 23 10:36:45 2009
 #
 CONFIG_ARM=y
 CONFIG_SYS_SUPPORTS_APM_EMULATION=y
@@ -197,9 +197,9 @@ CONFIG_OMAP_MCBSP=y
 CONFIG_OMAP_32K_TIMER=y
 CONFIG_OMAP_32K_TIMER_HZ=128
 CONFIG_OMAP_DM_TIMER=y
-# CONFIG_OMAP_LL_DEBUG_UART1 is not set
+CONFIG_OMAP_LL_DEBUG_UART1=y
 # CONFIG_OMAP_LL_DEBUG_UART2 is not set
-CONFIG_OMAP_LL_DEBUG_UART3=y
+# CONFIG_OMAP_LL_DEBUG_UART3 is not set
 CONFIG_OMAP_SERIAL_WAKE=y
 CONFIG_ARCH_OMAP34XX=y
 CONFIG_ARCH_OMAP3430=y
@@ -207,10 +207,10 @@ CONFIG_ARCH_OMAP3430=y
 #
 # OMAP Board Type
 #
-CONFIG_MACH_OMAP3_BEAGLE=y
-CONFIG_MACH_OMAP_LDP=y
-CONFIG_MACH_OVERO=y
-CONFIG_MACH_OMAP3_PANDORA=y
+# CONFIG_MACH_OMAP3_BEAGLE is not set
+# CONFIG_MACH_OMAP_LDP is not set
+# CONFIG_MACH_OVERO is not set
+# CONFIG_MACH_OMAP3_PANDORA is not set
 CONFIG_MACH_OMAP_3430SDP=y
 
 #
@@ -950,7 +950,7 @@ CONFIG_SPI_OMAP24XX=y
 # CONFIG_SPI_TLE62X0 is not set
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
-CONFIG_DEBUG_GPIO=y
+# CONFIG_DEBUG_GPIO is not set
 CONFIG_GPIO_SYSFS=y
 
 #
@@ -1370,7 +1370,7 @@ CONFIG_SND_OMAP_SOC=y
 CONFIG_SND_OMAP_SOC_MCBSP=y
 # CONFIG_SND_OMAP_SOC_OVERO is not set
 CONFIG_SND_OMAP_SOC_SDP3430=y
-CONFIG_SND_OMAP_SOC_OMAP3_PANDORA=y
+# CONFIG_SND_OMAP_SOC_OMAP3_PANDORA is not set
 CONFIG_SND_SOC_I2C_AND_SPI=y
 # CONFIG_SND_SOC_ALL_CODECS is not set
 CONFIG_SND_SOC_TWL4030=y

arch/arm/configs/rx51_defconfig

@@ -1006,6 +1006,7 @@ CONFIG_WATCHDOG=y
 #
 # CONFIG_SOFT_WATCHDOG is not set
 CONFIG_OMAP_WATCHDOG=m
+CONFIG_TWL4030_WATCHDOG=m
 
 #
 # USB-based Watchdog Cards

arch/arm/mach-omap1/board-ams-delta.c

@@ -15,8 +15,11 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/input.h>
+#include <linux/interrupt.h>
 #include <linux/platform_device.h>
+#include <linux/serial_8250.h>
 
+#include <asm/serial.h>
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -162,10 +165,6 @@ static struct omap_lcd_config ams_delta_lcd_config __initdata = {
 	.ctrl_name	= "internal",
 };
 
-static struct omap_uart_config ams_delta_uart_config __initdata = {
-	.enabled_uarts = 1,
-};
-
 static struct omap_usb_config ams_delta_usb_config __initdata = {
 	.register_host	= 1,
 	.hmc_mode	= 16,
@@ -174,7 +173,6 @@ static struct omap_usb_config ams_delta_usb_config __initdata = {
 
 static struct omap_board_config_kernel ams_delta_config[] = {
 	{ OMAP_TAG_LCD,		&ams_delta_lcd_config },
-	{ OMAP_TAG_UART,	&ams_delta_uart_config },
 };
 
 static struct resource ams_delta_kp_resources[] = {
@@ -235,6 +233,41 @@ static void __init ams_delta_init(void)
 	platform_add_devices(ams_delta_devices, ARRAY_SIZE(ams_delta_devices));
 }
 
+static struct plat_serial8250_port ams_delta_modem_ports[] = {
+	{
+		.membase	= (void *) AMS_DELTA_MODEM_VIRT,
+		.mapbase	= AMS_DELTA_MODEM_PHYS,
+		.irq		= -EINVAL, /* changed later */
+		.flags		= UPF_BOOT_AUTOCONF,
+		.irqflags	= IRQF_TRIGGER_RISING,
+		.iotype		= UPIO_MEM,
+		.regshift	= 1,
+		.uartclk	= BASE_BAUD * 16,
+	},
+	{ },
+};
+
+static struct platform_device ams_delta_modem_device = {
+	.name	= "serial8250",
+	.id	= PLAT8250_DEV_PLATFORM1,
+	.dev		= {
+		.platform_data = ams_delta_modem_ports,
+	},
+};
+
+static int __init ams_delta_modem_init(void)
+{
+	omap_cfg_reg(M14_1510_GPIO2);
+	ams_delta_modem_ports[0].irq = gpio_to_irq(2);
+
+	ams_delta_latch2_write(
+		AMS_DELTA_LATCH2_MODEM_NRESET | AMS_DELTA_LATCH2_MODEM_CODEC,
+		AMS_DELTA_LATCH2_MODEM_NRESET | AMS_DELTA_LATCH2_MODEM_CODEC);
+
+	return platform_device_register(&ams_delta_modem_device);
+}
+arch_initcall(ams_delta_modem_init);
+
 static void __init ams_delta_map_io(void)
 {
 	omap1_map_common_io();

arch/arm/mach-omap1/board-fsample.c

@@ -240,16 +240,11 @@ static int nand_dev_ready(struct omap_nand_platform_data *data)
 	return gpio_get_value(P2_NAND_RB_GPIO_PIN);
 }
 
-static struct omap_uart_config fsample_uart_config __initdata = {
-	.enabled_uarts = ((1 << 0) | (1 << 1)),
-};
-
 static struct omap_lcd_config fsample_lcd_config __initdata = {
 	.ctrl_name	= "internal",
 };
 
 static struct omap_board_config_kernel fsample_config[] = {
-	{ OMAP_TAG_UART,	&fsample_uart_config },
 	{ OMAP_TAG_LCD,		&fsample_lcd_config },
 };
 

arch/arm/mach-omap1/board-generic.c

@@ -57,12 +57,7 @@ static struct omap_usb_config generic1610_usb_config __initdata = {
 };
 #endif
 
-static struct omap_uart_config generic_uart_config __initdata = {
-	.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
-};
-
 static struct omap_board_config_kernel generic_config[] __initdata = {
-	{ OMAP_TAG_UART,	&generic_uart_config },
 };
 
 static void __init omap_generic_init(void)

arch/arm/mach-omap1/board-h2.c

@@ -360,16 +360,11 @@ static struct omap_usb_config h2_usb_config __initdata = {
 	.pins[1]	= 3,
 };
 
-static struct omap_uart_config h2_uart_config __initdata = {
-	.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
-};
-
 static struct omap_lcd_config h2_lcd_config __initdata = {
 	.ctrl_name	= "internal",
 };
 
 static struct omap_board_config_kernel h2_config[] __initdata = {
-	{ OMAP_TAG_UART,	&h2_uart_config },
 	{ OMAP_TAG_LCD,		&h2_lcd_config },
 };
 

arch/arm/mach-omap1/board-h3.c

@@ -313,16 +313,11 @@ static struct omap_usb_config h3_usb_config __initdata = {
 	.pins[1]	= 3,
 };
 
-static struct omap_uart_config h3_uart_config __initdata = {
-	.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
-};
-
 static struct omap_lcd_config h3_lcd_config __initdata = {
 	.ctrl_name	= "internal",
 };
 
 static struct omap_board_config_kernel h3_config[] __initdata = {
-	{ OMAP_TAG_UART,	&h3_uart_config },
 	{ OMAP_TAG_LCD,		&h3_lcd_config },
 };
 

arch/arm/mach-omap1/board-innovator.c

@@ -368,13 +368,8 @@ static inline void innovator_mmc_init(void)
 }
 #endif
 
-static struct omap_uart_config innovator_uart_config __initdata = {
-	.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
-};
-
 static struct omap_board_config_kernel innovator_config[] = {
 	{ OMAP_TAG_LCD,		NULL },
-	{ OMAP_TAG_UART,	&innovator_uart_config },
 };
 
 static void __init innovator_init(void)

arch/arm/mach-omap1/board-osk.c

@@ -293,10 +293,6 @@ static struct omap_usb_config osk_usb_config __initdata = {
 	.pins[0]	= 2,
 };
 
-static struct omap_uart_config osk_uart_config __initdata = {
-	.enabled_uarts = (1 << 0),
-};
-
 #ifdef	CONFIG_OMAP_OSK_MISTRAL
 static struct omap_lcd_config osk_lcd_config __initdata = {
 	.ctrl_name	= "internal",
@@ -304,7 +300,6 @@ static struct omap_lcd_config osk_lcd_config __initdata = {
 #endif
 
 static struct omap_board_config_kernel osk_config[] __initdata = {
-	{ OMAP_TAG_UART,		&osk_uart_config },
 #ifdef	CONFIG_OMAP_OSK_MISTRAL
 	{ OMAP_TAG_LCD,			&osk_lcd_config },
 #endif

arch/arm/mach-omap1/board-palmte.c

@@ -212,10 +212,6 @@ static struct omap_lcd_config palmte_lcd_config __initdata = {
 	.ctrl_name	= "internal",
 };
 
-static struct omap_uart_config palmte_uart_config __initdata = {
-	.enabled_uarts = (1 << 0) | (1 << 1) | (0 << 2),
-};
-
 #ifdef CONFIG_APM
 /*
  * Values measured in 10 minute intervals averaged over 10 samples.
@@ -302,7 +298,6 @@ static void palmte_get_power_status(struct apm_power_info *info, int *battery)
 
 static struct omap_board_config_kernel palmte_config[] __initdata = {
 	{ OMAP_TAG_LCD,		&palmte_lcd_config },
-	{ OMAP_TAG_UART,	&palmte_uart_config },
 };
 
 static struct spi_board_info palmte_spi_info[] __initdata = {

arch/arm/mach-omap1/board-palmtt.c

@@ -274,13 +274,8 @@ static struct omap_lcd_config palmtt_lcd_config __initdata = {
 	.ctrl_name	= "internal",
 };
 
-static struct omap_uart_config palmtt_uart_config __initdata = {
-	.enabled_uarts = (1 << 0) | (1 << 1) | (0 << 2),
-};
-
 static struct omap_board_config_kernel palmtt_config[] __initdata = {
 	{ OMAP_TAG_LCD,		&palmtt_lcd_config	},
-	{ OMAP_TAG_UART,	&palmtt_uart_config	},
 };
 
 static void __init omap_mpu_wdt_mode(int mode) {

arch/arm/mach-omap1/board-palmz71.c

@@ -244,13 +244,8 @@ static struct omap_lcd_config palmz71_lcd_config __initdata = {
 	.ctrl_name = "internal",
 };
 
-static struct omap_uart_config palmz71_uart_config __initdata = {
-	.enabled_uarts = (1 << 0) | (1 << 1) | (0 << 2),
-};
-
 static struct omap_board_config_kernel palmz71_config[] __initdata = {
 	{OMAP_TAG_LCD,	&palmz71_lcd_config},
-	{OMAP_TAG_UART,	&palmz71_uart_config},
 };
 
 static irqreturn_t

arch/arm/mach-omap1/board-perseus2.c

@@ -208,16 +208,11 @@ static int nand_dev_ready(struct omap_nand_platform_data *data)
 	return gpio_get_value(P2_NAND_RB_GPIO_PIN);
 }
 
-static struct omap_uart_config perseus2_uart_config __initdata = {
-	.enabled_uarts = ((1 << 0) | (1 << 1)),
-};
-
 static struct omap_lcd_config perseus2_lcd_config __initdata = {
 	.ctrl_name	= "internal",
 };
 
 static struct omap_board_config_kernel perseus2_config[] __initdata = {
-	{ OMAP_TAG_UART,	&perseus2_uart_config },
 	{ OMAP_TAG_LCD,		&perseus2_lcd_config },
 };
 

arch/arm/mach-omap1/board-sx1.c

@@ -369,13 +369,8 @@ static struct platform_device *sx1_devices[] __initdata = {
 };
 /*-----------------------------------------*/
 
-static struct omap_uart_config sx1_uart_config __initdata = {
-	.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
-};
-
 static struct omap_board_config_kernel sx1_config[] __initdata = {
 	{ OMAP_TAG_LCD,	&sx1_lcd_config },
-	{ OMAP_TAG_UART,	&sx1_uart_config },
 };
 
 /*-----------------------------------------*/

arch/arm/mach-omap1/board-voiceblue.c

@@ -140,12 +140,7 @@ static struct omap_usb_config voiceblue_usb_config __initdata = {
 	.pins[2]	= 6,
 };
 
-static struct omap_uart_config voiceblue_uart_config __initdata = {
-	.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
-};
-
 static struct omap_board_config_kernel voiceblue_config[] = {
-	{ OMAP_TAG_UART, &voiceblue_uart_config },
 };
 
 static void __init voiceblue_init_irq(void)

arch/arm/mach-omap1/devices.c

@@ -71,7 +71,7 @@ static inline void omap_init_rtc(void) {}
 #  define INT_DSP_MAILBOX1	INT_1610_DSP_MAILBOX1
 #endif
 
-#define OMAP1_MBOX_BASE		IO_ADDRESS(OMAP16XX_MAILBOX_BASE)
+#define OMAP1_MBOX_BASE		OMAP1_IO_ADDRESS(OMAP16XX_MAILBOX_BASE)
 
 static struct resource mbox_resources[] = {
 	{

arch/arm/mach-omap1/io.c

@@ -29,9 +29,9 @@ extern void omapfb_reserve_sdram(void);
  */
 static struct map_desc omap_io_desc[] __initdata = {
 	{
-		.virtual	= IO_VIRT,
-		.pfn		= __phys_to_pfn(IO_PHYS),
-		.length		= IO_SIZE,
+		.virtual	= OMAP1_IO_VIRT,
+		.pfn		= __phys_to_pfn(OMAP1_IO_PHYS),
+		.length		= OMAP1_IO_SIZE,
 		.type		= MT_DEVICE
 	}
 };

arch/arm/mach-omap1/pm.h

@@ -39,11 +39,11 @@
  * Register and offset definitions to be used in PM assembler code
  * ----------------------------------------------------------------------------
  */
-#define CLKGEN_REG_ASM_BASE		IO_ADDRESS(0xfffece00)
+#define CLKGEN_REG_ASM_BASE		OMAP1_IO_ADDRESS(0xfffece00)
 #define ARM_IDLECT1_ASM_OFFSET		0x04
 #define ARM_IDLECT2_ASM_OFFSET		0x08
 
-#define TCMIF_ASM_BASE			IO_ADDRESS(0xfffecc00)
+#define TCMIF_ASM_BASE			OMAP1_IO_ADDRESS(0xfffecc00)
 #define EMIFS_CONFIG_ASM_OFFSET		0x0c
 #define EMIFF_SDRAM_CONFIG_ASM_OFFSET	0x20
 

arch/arm/mach-omap1/serial.c

@@ -64,7 +64,7 @@ static void __init omap_serial_reset(struct plat_serial8250_port *p)
 
 static struct plat_serial8250_port serial_platform_data[] = {
 	{
-		.membase	= IO_ADDRESS(OMAP_UART1_BASE),
+		.membase	= OMAP1_IO_ADDRESS(OMAP_UART1_BASE),
 		.mapbase	= OMAP_UART1_BASE,
 		.irq		= INT_UART1,
 		.flags		= UPF_BOOT_AUTOCONF,
@@ -73,7 +73,7 @@ static struct plat_serial8250_port serial_platform_data[] = {
 		.uartclk	= OMAP16XX_BASE_BAUD * 16,
 	},
 	{
-		.membase	= IO_ADDRESS(OMAP_UART2_BASE),
+		.membase	= OMAP1_IO_ADDRESS(OMAP_UART2_BASE),
 		.mapbase	= OMAP_UART2_BASE,
 		.irq		= INT_UART2,
 		.flags		= UPF_BOOT_AUTOCONF,
@@ -82,7 +82,7 @@ static struct plat_serial8250_port serial_platform_data[] = {
 		.uartclk	= OMAP16XX_BASE_BAUD * 16,
 	},
 	{
-		.membase	= IO_ADDRESS(OMAP_UART3_BASE),
+		.membase	= OMAP1_IO_ADDRESS(OMAP_UART3_BASE),
 		.mapbase	= OMAP_UART3_BASE,
 		.irq		= INT_UART3,
 		.flags		= UPF_BOOT_AUTOCONF,
@@ -109,7 +109,6 @@ static struct platform_device serial_device = {
 void __init omap_serial_init(void)
 {
 	int i;
-	const struct omap_uart_config *info;
 
 	if (cpu_is_omap730()) {
 		serial_platform_data[0].regshift = 0;
@@ -131,19 +130,9 @@ void __init omap_serial_init(void)
 		serial_platform_data[2].uartclk = OMAP1510_BASE_BAUD * 16;
 	}
 
-	info = omap_get_config(OMAP_TAG_UART, struct omap_uart_config);
-	if (info == NULL)
-		return;
-
 	for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
 		unsigned char reg;
 
-		if (!((1 << i) & info->enabled_uarts)) {
-			serial_platform_data[i].membase = NULL;
-			serial_platform_data[i].mapbase = 0;
-			continue;
-		}
-
 		switch (i) {
 		case 0:
 			uart1_ck = clk_get(NULL, "uart1_ck");

arch/arm/mach-omap1/sram.S

@@ -21,13 +21,13 @@
 ENTRY(omap1_sram_reprogram_clock)
 	stmfd	sp!, {r0 - r12, lr}		@ save registers on stack
 
-	mov	r2, #IO_ADDRESS(DPLL_CTL) & 0xff000000
-	orr	r2, r2, #IO_ADDRESS(DPLL_CTL) & 0x00ff0000
-	orr	r2, r2, #IO_ADDRESS(DPLL_CTL) & 0x0000ff00
+	mov	r2, #OMAP1_IO_ADDRESS(DPLL_CTL) & 0xff000000
+	orr	r2, r2, #OMAP1_IO_ADDRESS(DPLL_CTL) & 0x00ff0000
+	orr	r2, r2, #OMAP1_IO_ADDRESS(DPLL_CTL) & 0x0000ff00
 
-	mov	r3, #IO_ADDRESS(ARM_CKCTL) & 0xff000000
-	orr	r3, r3, #IO_ADDRESS(ARM_CKCTL) & 0x00ff0000
-	orr	r3, r3, #IO_ADDRESS(ARM_CKCTL) & 0x0000ff00
+	mov	r3, #OMAP1_IO_ADDRESS(ARM_CKCTL) & 0xff000000
+	orr	r3, r3, #OMAP1_IO_ADDRESS(ARM_CKCTL) & 0x00ff0000
+	orr	r3, r3, #OMAP1_IO_ADDRESS(ARM_CKCTL) & 0x0000ff00
 
 	tst	r0, #1 << 4			@ want lock mode?
 	beq	newck				@ nope

arch/arm/mach-omap1/time.c

@@ -63,7 +63,7 @@ typedef struct {
 } omap_mpu_timer_regs_t;
 
 #define omap_mpu_timer_base(n)							\
-((volatile omap_mpu_timer_regs_t*)IO_ADDRESS(OMAP_MPU_TIMER_BASE +	\
+((volatile omap_mpu_timer_regs_t*)OMAP1_IO_ADDRESS(OMAP_MPU_TIMER_BASE +	\
 				 (n)*OMAP_MPU_TIMER_OFFSET))
 
 static inline unsigned long omap_mpu_timer_read(int nr)

arch/arm/mach-omap2/Kconfig

@@ -31,6 +31,11 @@ config MACH_OMAP_GENERIC
 	bool "Generic OMAP board"
 	depends on ARCH_OMAP2 && ARCH_OMAP24XX
 
+config MACH_OMAP2_TUSB6010
+	bool
+	depends on ARCH_OMAP2 && ARCH_OMAP2420
+	default y if MACH_NOKIA_N8X0
+
 config MACH_OMAP_H4
 	bool "OMAP 2420 H4 board"
 	depends on ARCH_OMAP2 && ARCH_OMAP24XX
@@ -68,6 +73,10 @@ config MACH_OMAP_3430SDP
 	bool "OMAP 3430 SDP board"
 	depends on ARCH_OMAP3 && ARCH_OMAP34XX
 
+config MACH_NOKIA_N8X0
+	bool "Nokia N800/N810"
+	depends on ARCH_OMAP2420
+
 config MACH_NOKIA_RX51
 	bool "Nokia RX-51 board"
 	depends on ARCH_OMAP3 && ARCH_OMAP34XX

arch/arm/mach-omap2/Makefile

@@ -5,7 +5,7 @@
 # Common support
 obj-y := id.o io.o control.o mux.o devices.o serial.o gpmc.o timer-gp.o
 
-omap-2-3-common				= irq.o sdrc.o
+omap-2-3-common				= irq.o sdrc.o omap_hwmod.o
 prcm-common				= prcm.o powerdomain.o
 clock-common				= clock.o clockdomain.o
 
@@ -35,6 +35,11 @@ obj-$(CONFIG_ARCH_OMAP3)		+= pm34xx.o sleep34xx.o
 obj-$(CONFIG_PM_DEBUG)			+= pm-debug.o
 endif
 
+# PRCM
+obj-$(CONFIG_ARCH_OMAP2)		+= cm.o
+obj-$(CONFIG_ARCH_OMAP3)		+= cm.o
+obj-$(CONFIG_ARCH_OMAP4)		+= cm4xxx.o
+
 # Clock framework
 obj-$(CONFIG_ARCH_OMAP2)		+= clock24xx.o
 obj-$(CONFIG_ARCH_OMAP3)		+= clock34xx.o
@@ -62,7 +67,7 @@ obj-$(CONFIG_MACH_OMAP3_PANDORA)	+= board-omap3pandora.o \
 					   mmc-twl4030.o
 obj-$(CONFIG_MACH_OMAP_3430SDP)		+= board-3430sdp.o \
 					   mmc-twl4030.o
-
+obj-$(CONFIG_MACH_NOKIA_N8X0)		+= board-n8x0.o
 obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51.o \
 					   board-rx51-peripherals.o \
 					   mmc-twl4030.o
@@ -74,6 +79,7 @@ obj-$(CONFIG_MACH_OMAP_4430SDP)		+= board-4430sdp.o
 
 # Platform specific device init code
 obj-y					+= usb-musb.o
+obj-$(CONFIG_MACH_OMAP2_TUSB6010)	+= usb-tusb6010.o
 
 onenand-$(CONFIG_MTD_ONENAND_OMAP2)	:= gpmc-onenand.o
 obj-y					+= $(onenand-m) $(onenand-y)

arch/arm/mach-omap2/board-2430sdp.c

@@ -139,23 +139,19 @@ static inline void board_smc91x_init(void)
 
 #endif
 
+static struct omap_board_config_kernel sdp2430_config[] = {
+	{OMAP_TAG_LCD, &sdp2430_lcd_config},
+};
+
 static void __init omap_2430sdp_init_irq(void)
 {
+	omap_board_config = sdp2430_config;
+	omap_board_config_size = ARRAY_SIZE(sdp2430_config);
 	omap2_init_common_hw(NULL, NULL);
 	omap_init_irq();
 	omap_gpio_init();
 }
 
-static struct omap_uart_config sdp2430_uart_config __initdata = {
-	.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
-};
-
-static struct omap_board_config_kernel sdp2430_config[] = {
-	{OMAP_TAG_UART, &sdp2430_uart_config},
-	{OMAP_TAG_LCD, &sdp2430_lcd_config},
-};
-
-
 static struct twl4030_gpio_platform_data sdp2430_gpio_data = {
 	.gpio_base	= OMAP_MAX_GPIO_LINES,
 	.irq_base	= TWL4030_GPIO_IRQ_BASE,
@@ -205,8 +201,6 @@ static void __init omap_2430sdp_init(void)
 	omap2430_i2c_init();
 
 	platform_add_devices(sdp2430_devices, ARRAY_SIZE(sdp2430_devices));
-	omap_board_config = sdp2430_config;
-	omap_board_config_size = ARRAY_SIZE(sdp2430_config);
 	omap_serial_init();
 	twl4030_mmc_init(mmc);
 	usb_musb_init();

arch/arm/mach-omap2/board-3430sdp.c

@@ -167,26 +167,23 @@ static struct platform_device *sdp3430_devices[] __initdata = {
 	&sdp3430_lcd_device,
 };
 
-static void __init omap_3430sdp_init_irq(void)
-{
-	omap2_init_common_hw(hyb18m512160af6_sdrc_params, NULL);
-	omap_init_irq();
-	omap_gpio_init();
-}
-
-static struct omap_uart_config sdp3430_uart_config __initdata = {
-	.enabled_uarts	= ((1 << 0) | (1 << 1) | (1 << 2)),
-};
-
 static struct omap_lcd_config sdp3430_lcd_config __initdata = {
 	.ctrl_name	= "internal",
 };
 
 static struct omap_board_config_kernel sdp3430_config[] __initdata = {
-	{ OMAP_TAG_UART,	&sdp3430_uart_config },
 	{ OMAP_TAG_LCD,		&sdp3430_lcd_config },
 };
 
+static void __init omap_3430sdp_init_irq(void)
+{
+	omap_board_config = sdp3430_config;
+	omap_board_config_size = ARRAY_SIZE(sdp3430_config);
+	omap2_init_common_hw(hyb18m512160af6_sdrc_params, NULL);
+	omap_init_irq();
+	omap_gpio_init();
+}
+
 static int sdp3430_batt_table[] = {
 /* 0 C*/
 30800, 29500, 28300, 27100,
@@ -478,12 +475,15 @@ static inline void board_smc91x_init(void)
 
 #endif
 
+static void enable_board_wakeup_source(void)
+{
+	omap_cfg_reg(AF26_34XX_SYS_NIRQ); /* T2 interrupt line (keypad) */
+}
+
 static void __init omap_3430sdp_init(void)
 {
 	omap3430_i2c_init();
 	platform_add_devices(sdp3430_devices, ARRAY_SIZE(sdp3430_devices));
-	omap_board_config = sdp3430_config;
-	omap_board_config_size = ARRAY_SIZE(sdp3430_config);
 	if (omap_rev() > OMAP3430_REV_ES1_0)
 		ts_gpio = SDP3430_TS_GPIO_IRQ_SDPV2;
 	else
@@ -495,6 +495,7 @@ static void __init omap_3430sdp_init(void)
 	omap_serial_init();
 	usb_musb_init();
 	board_smc91x_init();
+	enable_board_wakeup_source();
 }
 
 static void __init omap_3430sdp_map_io(void)

arch/arm/mach-omap2/board-4430sdp.c

@@ -47,14 +47,13 @@ static struct omap_lcd_config sdp4430_lcd_config __initdata = {
 };
 
 static struct omap_board_config_kernel sdp4430_config[] __initdata = {
-	{ OMAP_TAG_UART,	&sdp4430_uart_config },
 	{ OMAP_TAG_LCD,		&sdp4430_lcd_config },
 };
 
 static void __init gic_init_irq(void)
 {
-	gic_dist_init(0, IO_ADDRESS(OMAP44XX_GIC_DIST_BASE), 29);
-	gic_cpu_init(0, IO_ADDRESS(OMAP44XX_GIC_CPU_BASE));
+	gic_dist_init(0, OMAP2_IO_ADDRESS(OMAP44XX_GIC_DIST_BASE), 29);
+	gic_cpu_init(0, OMAP2_IO_ADDRESS(OMAP44XX_GIC_CPU_BASE));
 }
 
 static void __init omap_4430sdp_init_irq(void)

arch/arm/mach-omap2/board-apollon.c

@@ -248,18 +248,6 @@ static inline void __init apollon_init_smc91x(void)
 	clk_put(gpmc_fck);
 }
 
-static void __init omap_apollon_init_irq(void)
-{
-	omap2_init_common_hw(NULL, NULL);
-	omap_init_irq();
-	omap_gpio_init();
-	apollon_init_smc91x();
-}
-
-static struct omap_uart_config apollon_uart_config __initdata = {
-	.enabled_uarts = (1 << 0) | (0 << 1) | (0 << 2),
-};
-
 static struct omap_usb_config apollon_usb_config __initdata = {
 	.register_dev	= 1,
 	.hmc_mode	= 0x14,	/* 0:dev 1:host1 2:disable */
@@ -272,10 +260,19 @@ static struct omap_lcd_config apollon_lcd_config __initdata = {
 };
 
 static struct omap_board_config_kernel apollon_config[] = {
-	{ OMAP_TAG_UART,	&apollon_uart_config },
 	{ OMAP_TAG_LCD,		&apollon_lcd_config },
 };
 
+static void __init omap_apollon_init_irq(void)
+{
+	omap_board_config = apollon_config;
+	omap_board_config_size = ARRAY_SIZE(apollon_config);
+	omap2_init_common_hw(NULL, NULL);
+	omap_init_irq();
+	omap_gpio_init();
+	apollon_init_smc91x();
+}
+
 static void __init apollon_led_init(void)
 {
 	/* LED0 - AA10 */
@@ -324,8 +321,6 @@ static void __init omap_apollon_init(void)
 	 * if not needed.
 	 */
 	platform_add_devices(apollon_devices, ARRAY_SIZE(apollon_devices));
-	omap_board_config = apollon_config;
-	omap_board_config_size = ARRAY_SIZE(apollon_config);
 	omap_serial_init();
 }
 

arch/arm/mach-omap2/board-generic.c

@@ -31,24 +31,19 @@
 #include <mach/board.h>
 #include <mach/common.h>
 
+static struct omap_board_config_kernel generic_config[] = {
+};
+
 static void __init omap_generic_init_irq(void)
 {
+	omap_board_config = generic_config;
+	omap_board_config_size = ARRAY_SIZE(generic_config);
 	omap2_init_common_hw(NULL, NULL);
 	omap_init_irq();
 }
 
-static struct omap_uart_config generic_uart_config __initdata = {
-	.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
-};
-
-static struct omap_board_config_kernel generic_config[] = {
-	{ OMAP_TAG_UART,	&generic_uart_config },
-};
-
 static void __init omap_generic_init(void)
 {
-	omap_board_config = generic_config;
-	omap_board_config_size = ARRAY_SIZE(generic_config);
 	omap_serial_init();
 }
 

arch/arm/mach-omap2/board-h4.c

@@ -268,18 +268,6 @@ static void __init h4_init_flash(void)
 	h4_flash_resource.end	= base + SZ_64M - 1;
 }
 
-static void __init omap_h4_init_irq(void)
-{
-	omap2_init_common_hw(NULL, NULL);
-	omap_init_irq();
-	omap_gpio_init();
-	h4_init_flash();
-}
-
-static struct omap_uart_config h4_uart_config __initdata = {
-	.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
-};
-
 static struct omap_lcd_config h4_lcd_config __initdata = {
 	.ctrl_name	= "internal",
 };
@@ -318,10 +306,19 @@ static struct omap_usb_config h4_usb_config __initdata = {
 };
 
 static struct omap_board_config_kernel h4_config[] = {
-	{ OMAP_TAG_UART,	&h4_uart_config },
 	{ OMAP_TAG_LCD,		&h4_lcd_config },
 };
 
+static void __init omap_h4_init_irq(void)
+{
+	omap_board_config = h4_config;
+	omap_board_config_size = ARRAY_SIZE(h4_config);
+	omap2_init_common_hw(NULL, NULL);
+	omap_init_irq();
+	omap_gpio_init();
+	h4_init_flash();
+}
+
 static struct at24_platform_data m24c01 = {
 	.byte_len	= SZ_1K / 8,
 	.page_size	= 16,
@@ -366,8 +363,6 @@ static void __init omap_h4_init(void)
 			ARRAY_SIZE(h4_i2c_board_info));
 
 	platform_add_devices(h4_devices, ARRAY_SIZE(h4_devices));
-	omap_board_config = h4_config;
-	omap_board_config_size = ARRAY_SIZE(h4_config);
 	omap_usb_init(&h4_usb_config);
 	omap_serial_init();
 }

arch/arm/mach-omap2/board-ldp.c

@@ -268,18 +268,6 @@ static inline void __init ldp_init_smsc911x(void)
 	gpio_direction_input(eth_gpio);
 }
 
-static void __init omap_ldp_init_irq(void)
-{
-	omap2_init_common_hw(NULL, NULL);
-	omap_init_irq();
-	omap_gpio_init();
-	ldp_init_smsc911x();
-}
-
-static struct omap_uart_config ldp_uart_config __initdata = {
-	.enabled_uarts	= ((1 << 0) | (1 << 1) | (1 << 2)),
-};
-
 static struct platform_device ldp_lcd_device = {
 	.name		= "ldp_lcd",
 	.id		= -1,
@@ -290,10 +278,19 @@ static struct omap_lcd_config ldp_lcd_config __initdata = {
 };
 
 static struct omap_board_config_kernel ldp_config[] __initdata = {
-	{ OMAP_TAG_UART,	&ldp_uart_config },
 	{ OMAP_TAG_LCD,		&ldp_lcd_config },
 };
 
+static void __init omap_ldp_init_irq(void)
+{
+	omap_board_config = ldp_config;
+	omap_board_config_size = ARRAY_SIZE(ldp_config);
+	omap2_init_common_hw(NULL, NULL);
+	omap_init_irq();
+	omap_gpio_init();
+	ldp_init_smsc911x();
+}
+
 static struct twl4030_usb_data ldp_usb_data = {
 	.usb_mode	= T2_USB_MODE_ULPI,
 };
@@ -377,8 +374,6 @@ static void __init omap_ldp_init(void)
 {
 	omap_i2c_init();
 	platform_add_devices(ldp_devices, ARRAY_SIZE(ldp_devices));
-	omap_board_config = ldp_config;
-	omap_board_config_size = ARRAY_SIZE(ldp_config);
 	ts_gpio = 54;
 	ldp_spi_board_info[0].irq = gpio_to_irq(ts_gpio);
 	spi_register_board_info(ldp_spi_board_info,

arch/arm/mach-omap2/board-n8x0.c

+/*
+ * linux/arch/arm/mach-omap2/board-n8x0.c
+ *
+ * Copyright (C) 2005-2009 Nokia Corporation
+ * Author: Juha Yrjola <juha.yrjola@nokia.com>
+ *
+ * Modified from mach-omap2/board-generic.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/stddef.h>
+#include <linux/spi/spi.h>
+#include <linux/usb/musb.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach-types.h>
+
+#include <mach/board.h>
+#include <mach/common.h>
+#include <mach/irqs.h>
+#include <mach/mcspi.h>
+#include <mach/onenand.h>
+#include <mach/serial.h>
+
+static struct omap2_mcspi_device_config p54spi_mcspi_config = {
+	.turbo_mode	= 0,
+	.single_channel = 1,
+};
+
+static struct spi_board_info n800_spi_board_info[] __initdata = {
+	{
+		.modalias	= "p54spi",
+		.bus_num	= 2,
+		.chip_select	= 0,
+		.max_speed_hz   = 48000000,
+		.controller_data = &p54spi_mcspi_config,
+	},
+};
+
+#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
+	defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
+
+static struct mtd_partition onenand_partitions[] = {
+	{
+		.name           = "bootloader",
+		.offset         = 0,
+		.size           = 0x20000,
+		.mask_flags     = MTD_WRITEABLE,	/* Force read-only */
+	},
+	{
+		.name           = "config",
+		.offset         = MTDPART_OFS_APPEND,
+		.size           = 0x60000,
+	},
+	{
+		.name           = "kernel",
+		.offset         = MTDPART_OFS_APPEND,
+		.size           = 0x200000,
+	},
+	{
+		.name           = "initfs",
+		.offset         = MTDPART_OFS_APPEND,
+		.size           = 0x400000,
+	},
+	{
+		.name           = "rootfs",
+		.offset         = MTDPART_OFS_APPEND,
+		.size           = MTDPART_SIZ_FULL,
+	},
+};
+
+static struct omap_onenand_platform_data board_onenand_data = {
+	.cs		= 0,
+	.gpio_irq	= 26,
+	.parts		= onenand_partitions,
+	.nr_parts	= ARRAY_SIZE(onenand_partitions),
+	.flags		= ONENAND_SYNC_READ,
+};
+
+static void __init n8x0_onenand_init(void)
+{
+	gpmc_onenand_init(&board_onenand_data);
+}
+
+#else
+
+static void __init n8x0_onenand_init(void) {}
+
+#endif
+
+static void __init n8x0_map_io(void)
+{
+	omap2_set_globals_242x();
+	omap2_map_common_io();
+}
+
+static void __init n8x0_init_irq(void)
+{
+	omap2_init_common_hw(NULL, NULL);
+	omap_init_irq();
+	omap_gpio_init();
+}
+
+static void __init n8x0_init_machine(void)
+{
+	/* FIXME: add n810 spi devices */
+	spi_register_board_info(n800_spi_board_info,
+				ARRAY_SIZE(n800_spi_board_info));
+
+	omap_serial_init();
+	n8x0_onenand_init();
+}
+
+MACHINE_START(NOKIA_N800, "Nokia N800")
+	.phys_io	= 0x48000000,
+	.io_pg_offst	= ((0xd8000000) >> 18) & 0xfffc,
+	.boot_params	= 0x80000100,
+	.map_io		= n8x0_map_io,
+	.init_irq	= n8x0_init_irq,
+	.init_machine	= n8x0_init_machine,
+	.timer		= &omap_timer,
+MACHINE_END
+
+MACHINE_START(NOKIA_N810, "Nokia N810")
+	.phys_io	= 0x48000000,
+	.io_pg_offst	= ((0xd8000000) >> 18) & 0xfffc,
+	.boot_params	= 0x80000100,
+	.map_io		= n8x0_map_io,
+	.init_irq	= n8x0_init_irq,
+	.init_machine	= n8x0_init_machine,
+	.timer		= &omap_timer,
+MACHINE_END
+
+MACHINE_START(NOKIA_N810_WIMAX, "Nokia N810 WiMAX")
+	.phys_io	= 0x48000000,
+	.io_pg_offst	= ((0xd8000000) >> 18) & 0xfffc,
+	.boot_params	= 0x80000100,
+	.map_io		= n8x0_map_io,
+	.init_irq	= n8x0_init_irq,
+	.init_machine	= n8x0_init_machine,
+	.timer		= &omap_timer,
+MACHINE_END

arch/arm/mach-omap2/board-omap3beagle.c

@@ -108,10 +108,6 @@ static struct platform_device omap3beagle_nand_device = {
 
 #include "sdram-micron-mt46h32m32lf-6.h"
 
-static struct omap_uart_config omap3_beagle_uart_config __initdata = {
-	.enabled_uarts	= ((1 << 0) | (1 << 1) | (1 << 2)),
-};
-
 static struct twl4030_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
@@ -249,11 +245,16 @@ static struct regulator_init_data beagle_vpll2 = {
 	.consumer_supplies	= &beagle_vdvi_supply,
 };
 
+static struct twl4030_usb_data beagle_usb_data = {
+	.usb_mode	= T2_USB_MODE_ULPI,
+};
+
 static struct twl4030_platform_data beagle_twldata = {
 	.irq_base	= TWL4030_IRQ_BASE,
 	.irq_end	= TWL4030_IRQ_END,
 
 	/* platform_data for children goes here */
+	.usb		= &beagle_usb_data,
 	.gpio		= &beagle_gpio_data,
 	.vmmc1		= &beagle_vmmc1,
 	.vsim		= &beagle_vsim,
@@ -280,17 +281,6 @@ static int __init omap3_beagle_i2c_init(void)
 	return 0;
 }
 
-static void __init omap3_beagle_init_irq(void)
-{
-	omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
-			     mt46h32m32lf6_sdrc_params);
-	omap_init_irq();
-#ifdef CONFIG_OMAP_32K_TIMER
-	omap2_gp_clockevent_set_gptimer(12);
-#endif
-	omap_gpio_init();
-}
-
 static struct gpio_led gpio_leds[] = {
 	{
 		.name			= "beagleboard::usr0",
@@ -345,10 +335,22 @@ static struct platform_device keys_gpio = {
 };
 
 static struct omap_board_config_kernel omap3_beagle_config[] __initdata = {
-	{ OMAP_TAG_UART,	&omap3_beagle_uart_config },
 	{ OMAP_TAG_LCD,		&omap3_beagle_lcd_config },
 };
 
+static void __init omap3_beagle_init_irq(void)
+{
+	omap_board_config = omap3_beagle_config;
+	omap_board_config_size = ARRAY_SIZE(omap3_beagle_config);
+	omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
+			     mt46h32m32lf6_sdrc_params);
+	omap_init_irq();
+#ifdef CONFIG_OMAP_32K_TIMER
+	omap2_gp_clockevent_set_gptimer(12);
+#endif
+	omap_gpio_init();
+}
+
 static struct platform_device *omap3_beagle_devices[] __initdata = {
 	&omap3_beagle_lcd_device,
 	&leds_gpio,
@@ -398,8 +400,6 @@ static void __init omap3_beagle_init(void)
 	omap3_beagle_i2c_init();
 	platform_add_devices(omap3_beagle_devices,
 			ARRAY_SIZE(omap3_beagle_devices));
-	omap_board_config = omap3_beagle_config;
-	omap_board_config_size = ARRAY_SIZE(omap3_beagle_config);
 	omap_serial_init();
 
 	omap_cfg_reg(J25_34XX_GPIO170);

arch/arm/mach-omap2/board-omap3evm.c

@@ -92,10 +92,6 @@ static inline void __init omap3evm_init_smc911x(void)
 	gpio_direction_input(OMAP3EVM_ETHR_GPIO_IRQ);
 }
 
-static struct omap_uart_config omap3_evm_uart_config __initdata = {
-	.enabled_uarts	= ((1 << 0) | (1 << 1) | (1 << 2)),
-};
-
 static struct twl4030_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
@@ -278,19 +274,20 @@ struct spi_board_info omap3evm_spi_board_info[] = {
 	},
 };
 
+static struct omap_board_config_kernel omap3_evm_config[] __initdata = {
+	{ OMAP_TAG_LCD,		&omap3_evm_lcd_config },
+};
+
 static void __init omap3_evm_init_irq(void)
 {
+	omap_board_config = omap3_evm_config;
+	omap_board_config_size = ARRAY_SIZE(omap3_evm_config);
 	omap2_init_common_hw(mt46h32m32lf6_sdrc_params, NULL);
 	omap_init_irq();
 	omap_gpio_init();
 	omap3evm_init_smc911x();
 }
 
-static struct omap_board_config_kernel omap3_evm_config[] __initdata = {
-	{ OMAP_TAG_UART,	&omap3_evm_uart_config },
-	{ OMAP_TAG_LCD,		&omap3_evm_lcd_config },
-};
-
 static struct platform_device *omap3_evm_devices[] __initdata = {
 	&omap3_evm_lcd_device,
 	&omap3evm_smc911x_device,
@@ -301,8 +298,6 @@ static void __init omap3_evm_init(void)
 	omap3_evm_i2c_init();
 
 	platform_add_devices(omap3_evm_devices, ARRAY_SIZE(omap3_evm_devices));
-	omap_board_config = omap3_evm_config;
-	omap_board_config_size = ARRAY_SIZE(omap3_evm_config);
 
 	spi_register_board_info(omap3evm_spi_board_info,
 				ARRAY_SIZE(omap3evm_spi_board_info));

arch/arm/mach-omap2/board-omap3pandora.c

@@ -213,10 +213,6 @@ static struct twl4030_hsmmc_info omap3pandora_mmc[] = {
 	{}	/* Terminator */
 };
 
-static struct omap_uart_config omap3pandora_uart_config __initdata = {
-	.enabled_uarts	= (1 << 2), /* UART3 */
-};
-
 static struct regulator_consumer_supply pandora_vmmc1_supply = {
 	.supply			= "vmmc",
 };
@@ -309,14 +305,6 @@ static int __init omap3pandora_i2c_init(void)
 	return 0;
 }
 
-static void __init omap3pandora_init_irq(void)
-{
-	omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
-			     mt46h32m32lf6_sdrc_params);
-	omap_init_irq();
-	omap_gpio_init();
-}
-
 static void __init omap3pandora_ads7846_init(void)
 {
 	int gpio = OMAP3_PANDORA_TS_GPIO;
@@ -376,10 +364,19 @@ static struct omap_lcd_config omap3pandora_lcd_config __initdata = {
 };
 
 static struct omap_board_config_kernel omap3pandora_config[] __initdata = {
-	{ OMAP_TAG_UART,	&omap3pandora_uart_config },
 	{ OMAP_TAG_LCD,		&omap3pandora_lcd_config },
 };
 
+static void __init omap3pandora_init_irq(void)
+{
+	omap_board_config = omap3pandora_config;
+	omap_board_config_size = ARRAY_SIZE(omap3pandora_config);
+	omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
+			     mt46h32m32lf6_sdrc_params);
+	omap_init_irq();
+	omap_gpio_init();
+}
+
 static struct platform_device *omap3pandora_devices[] __initdata = {
 	&omap3pandora_lcd_device,
 	&pandora_leds_gpio,
@@ -391,8 +388,6 @@ static void __init omap3pandora_init(void)
 	omap3pandora_i2c_init();
 	platform_add_devices(omap3pandora_devices,
 			ARRAY_SIZE(omap3pandora_devices));
-	omap_board_config = omap3pandora_config;
-	omap_board_config_size = ARRAY_SIZE(omap3pandora_config);
 	omap_serial_init();
 	spi_register_board_info(omap3pandora_spi_board_info,
 			ARRAY_SIZE(omap3pandora_spi_board_info));

arch/arm/mach-omap2/board-overo.c

@@ -271,9 +271,6 @@ static void __init overo_flash_init(void)
 			printk(KERN_ERR "Unable to register NAND device\n");
 	}
 }
-static struct omap_uart_config overo_uart_config __initdata = {
-	.enabled_uarts	= ((1 << 0) | (1 << 1) | (1 << 2)),
-};
 
 static struct twl4030_hsmmc_info mmc[] = {
 	{
@@ -360,14 +357,6 @@ static int __init overo_i2c_init(void)
 	return 0;
 }
 
-static void __init overo_init_irq(void)
-{
-	omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
-			     mt46h32m32lf6_sdrc_params);
-	omap_init_irq();
-	omap_gpio_init();
-}
-
 static struct platform_device overo_lcd_device = {
 	.name		= "overo_lcd",
 	.id		= -1,
@@ -378,10 +367,19 @@ static struct omap_lcd_config overo_lcd_config __initdata = {
 };
 
 static struct omap_board_config_kernel overo_config[] __initdata = {
-	{ OMAP_TAG_UART,	&overo_uart_config },
 	{ OMAP_TAG_LCD,		&overo_lcd_config },
 };
 
+static void __init overo_init_irq(void)
+{
+	omap_board_config = overo_config;
+	omap_board_config_size = ARRAY_SIZE(overo_config);
+	omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
+			     mt46h32m32lf6_sdrc_params);
+	omap_init_irq();
+	omap_gpio_init();
+}
+
 static struct platform_device *overo_devices[] __initdata = {
 	&overo_lcd_device,
 };
@@ -390,8 +388,6 @@ static void __init overo_init(void)
 {
 	overo_i2c_init();
 	platform_add_devices(overo_devices, ARRAY_SIZE(overo_devices));
-	omap_board_config = overo_config;
-	omap_board_config_size = ARRAY_SIZE(overo_config);
 	omap_serial_init();
 	overo_flash_init();
 	usb_musb_init();

arch/arm/mach-omap2/board-rx51.c

@@ -31,10 +31,6 @@
 #include <mach/gpmc.h>
 #include <mach/usb.h>
 
-static struct omap_uart_config rx51_uart_config = {
-	.enabled_uarts	= ((1 << 0) | (1 << 1) | (1 << 2)),
-};
-
 static struct omap_lcd_config rx51_lcd_config = {
 	.ctrl_name	= "internal",
 };
@@ -52,7 +48,6 @@ static struct omap_fbmem_config rx51_fbmem2_config = {
 };
 
 static struct omap_board_config_kernel rx51_config[] = {
-	{ OMAP_TAG_UART,	&rx51_uart_config },
 	{ OMAP_TAG_FBMEM,	&rx51_fbmem0_config },
 	{ OMAP_TAG_FBMEM,	&rx51_fbmem1_config },
 	{ OMAP_TAG_FBMEM,	&rx51_fbmem2_config },
@@ -61,6 +56,8 @@ static struct omap_board_config_kernel rx51_config[] = {
 
 static void __init rx51_init_irq(void)
 {
+	omap_board_config = rx51_config;
+	omap_board_config_size = ARRAY_SIZE(rx51_config);
 	omap2_init_common_hw(NULL, NULL);
 	omap_init_irq();
 	omap_gpio_init();
@@ -70,8 +67,6 @@ extern void __init rx51_peripherals_init(void);
 
 static void __init rx51_init(void)
 {
-	omap_board_config = rx51_config;
-	omap_board_config_size = ARRAY_SIZE(rx51_config);
 	omap_serial_init();
 	usb_musb_init();
 	rx51_peripherals_init();

arch/arm/mach-omap2/board-zoom-debugboard.c

@@ -12,6 +12,7 @@
 #include <linux/gpio.h>
 #include <linux/serial_8250.h>
 #include <linux/smsc911x.h>
+#include <linux/interrupt.h>
 
 #include <mach/gpmc.h>
 
@@ -84,6 +85,7 @@ static struct plat_serial8250_port serial_platform_data[] = {
 		.mapbase	= 0x10000000,
 		.irq		= OMAP_GPIO_IRQ(102),
 		.flags		= UPF_BOOT_AUTOCONF|UPF_IOREMAP|UPF_SHARE_IRQ,
+		.irqflags	= IRQF_SHARED | IRQF_TRIGGER_RISING,
 		.iotype		= UPIO_MEM,
 		.regshift	= 1,
 		.uartclk	= QUART_CLK,
@@ -94,7 +96,7 @@ static struct plat_serial8250_port serial_platform_data[] = {
 
 static struct platform_device zoom2_debugboard_serial_device = {
 	.name			= "serial8250",
-	.id			= PLAT8250_DEV_PLATFORM1,
+	.id			= 3,
 	.dev			= {
 		.platform_data	= serial_platform_data,
 	},
@@ -127,6 +129,7 @@ static inline void __init zoom2_init_quaduart(void)
 static inline int omap_zoom2_debugboard_detect(void)
 {
 	int debug_board_detect = 0;
+	int ret = 1;
 
 	debug_board_detect = ZOOM2_SMSC911X_GPIO;
 
@@ -138,10 +141,10 @@ static inline int omap_zoom2_debugboard_detect(void)
 	gpio_direction_input(debug_board_detect);
 
 	if (!gpio_get_value(debug_board_detect)) {
-		gpio_free(debug_board_detect);
-		return 0;
+		ret = 0;
 	}
-	return 1;
+	gpio_free(debug_board_detect);
+	return ret;
 }
 
 static struct platform_device *zoom2_devices[] __initdata = {

arch/arm/mach-omap2/board-zoom2.c

@@ -12,36 +12,217 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
+#include <linux/input.h>
 #include <linux/gpio.h>
 #include <linux/i2c/twl4030.h>
+#include <linux/regulator/machine.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
 #include <mach/common.h>
 #include <mach/usb.h>
+#include <mach/keypad.h>
 
 #include "mmc-twl4030.h"
 
-static void __init omap_zoom2_init_irq(void)
+/* Zoom2 has Qwerty keyboard*/
+static int zoom2_twl4030_keymap[] = {
+	KEY(0, 0, KEY_E),
+	KEY(1, 0, KEY_R),
+	KEY(2, 0, KEY_T),
+	KEY(3, 0, KEY_HOME),
+	KEY(6, 0, KEY_I),
+	KEY(7, 0, KEY_LEFTSHIFT),
+	KEY(0, 1, KEY_D),
+	KEY(1, 1, KEY_F),
+	KEY(2, 1, KEY_G),
+	KEY(3, 1, KEY_SEND),
+	KEY(6, 1, KEY_K),
+	KEY(7, 1, KEY_ENTER),
+	KEY(0, 2, KEY_X),
+	KEY(1, 2, KEY_C),
+	KEY(2, 2, KEY_V),
+	KEY(3, 2, KEY_END),
+	KEY(6, 2, KEY_DOT),
+	KEY(7, 2, KEY_CAPSLOCK),
+	KEY(0, 3, KEY_Z),
+	KEY(1, 3, KEY_KPPLUS),
+	KEY(2, 3, KEY_B),
+	KEY(3, 3, KEY_F1),
+	KEY(6, 3, KEY_O),
+	KEY(7, 3, KEY_SPACE),
+	KEY(0, 4, KEY_W),
+	KEY(1, 4, KEY_Y),
+	KEY(2, 4, KEY_U),
+	KEY(3, 4, KEY_F2),
+	KEY(4, 4, KEY_VOLUMEUP),
+	KEY(6, 4, KEY_L),
+	KEY(7, 4, KEY_LEFT),
+	KEY(0, 5, KEY_S),
+	KEY(1, 5, KEY_H),
+	KEY(2, 5, KEY_J),
+	KEY(3, 5, KEY_F3),
+	KEY(5, 5, KEY_VOLUMEDOWN),
+	KEY(6, 5, KEY_M),
+	KEY(4, 5, KEY_ENTER),
+	KEY(7, 5, KEY_RIGHT),
+	KEY(0, 6, KEY_Q),
+	KEY(1, 6, KEY_A),
+	KEY(2, 6, KEY_N),
+	KEY(3, 6, KEY_BACKSPACE),
+	KEY(6, 6, KEY_P),
+	KEY(7, 6, KEY_UP),
+	KEY(6, 7, KEY_SELECT),
+	KEY(7, 7, KEY_DOWN),
+	KEY(0, 7, KEY_PROG1),	/*MACRO 1 <User defined> */
+	KEY(1, 7, KEY_PROG2),	/*MACRO 2 <User defined> */
+	KEY(2, 7, KEY_PROG3),	/*MACRO 3 <User defined> */
+	KEY(3, 7, KEY_PROG4),	/*MACRO 4 <User defined> */
+	0
+};
+
+static struct twl4030_keypad_data zoom2_kp_twl4030_data = {
+	.rows		= 8,
+	.cols		= 8,
+	.keymap		= zoom2_twl4030_keymap,
+	.keymapsize	= ARRAY_SIZE(zoom2_twl4030_keymap),
+	.rep		= 1,
+};
+
+static struct omap_board_config_kernel zoom2_config[] __initdata = {
+};
+
+static struct regulator_consumer_supply zoom2_vmmc1_supply = {
+	.supply		= "vmmc",
+};
+
+static struct regulator_consumer_supply zoom2_vsim_supply = {
+	.supply		= "vmmc_aux",
+};
+
+static struct regulator_consumer_supply zoom2_vmmc2_supply = {
+	.supply		= "vmmc",
+};
+
+/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
+static struct regulator_init_data zoom2_vmmc1 = {
+	.constraints = {
+		.min_uV			= 1850000,
+		.max_uV			= 3150000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
+					| REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies  = 1,
+	.consumer_supplies      = &zoom2_vmmc1_supply,
+};
+
+/* VMMC2 for MMC2 card */
+static struct regulator_init_data zoom2_vmmc2 = {
+	.constraints = {
+		.min_uV			= 1850000,
+		.max_uV			= 1850000,
+		.apply_uV		= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies  = 1,
+	.consumer_supplies      = &zoom2_vmmc2_supply,
+};
+
+/* VSIM for OMAP VDD_MMC1A (i/o for DAT4..DAT7) */
+static struct regulator_init_data zoom2_vsim = {
+	.constraints = {
+		.min_uV			= 1800000,
+		.max_uV			= 3000000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
+					| REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies  = 1,
+	.consumer_supplies      = &zoom2_vsim_supply,
+};
+
+static struct twl4030_hsmmc_info mmc[] __initdata = {
+	{
+		.mmc		= 1,
+		.wires		= 4,
+		.gpio_wp	= -EINVAL,
+	},
+	{
+		.mmc		= 2,
+		.wires		= 4,
+		.gpio_wp	= -EINVAL,
+	},
+	{}      /* Terminator */
+};
+
+static int zoom2_twl_gpio_setup(struct device *dev,
+		unsigned gpio, unsigned ngpio)
 {
-	omap2_init_common_hw(NULL, NULL);
-	omap_init_irq();
-	omap_gpio_init();
+	/* gpio + 0 is "mmc0_cd" (input/IRQ),
+	 * gpio + 1 is "mmc1_cd" (input/IRQ)
+	 */
+	mmc[0].gpio_cd = gpio + 0;
+	mmc[1].gpio_cd = gpio + 1;
+	twl4030_mmc_init(mmc);
+
+	/* link regulators to MMC adapters ... we "know" the
+	 * regulators will be set up only *after* we return.
+	*/
+	zoom2_vmmc1_supply.dev = mmc[0].dev;
+	zoom2_vsim_supply.dev = mmc[0].dev;
+	zoom2_vmmc2_supply.dev = mmc[1].dev;
+
+	return 0;
 }
 
-static struct omap_uart_config zoom2_uart_config __initdata = {
-	.enabled_uarts	= ((1 << 0) | (1 << 1) | (1 << 2)),
+
+static int zoom2_batt_table[] = {
+/* 0 C*/
+30800, 29500, 28300, 27100,
+26000, 24900, 23900, 22900, 22000, 21100, 20300, 19400, 18700, 17900,
+17200, 16500, 15900, 15300, 14700, 14100, 13600, 13100, 12600, 12100,
+11600, 11200, 10800, 10400, 10000, 9630,  9280,  8950,  8620,  8310,
+8020,  7730,  7460,  7200,  6950,  6710,  6470,  6250,  6040,  5830,
+5640,  5450,  5260,  5090,  4920,  4760,  4600,  4450,  4310,  4170,
+4040,  3910,  3790,  3670,  3550
 };
 
-static struct omap_board_config_kernel zoom2_config[] __initdata = {
-	{ OMAP_TAG_UART,	&zoom2_uart_config },
+static struct twl4030_bci_platform_data zoom2_bci_data = {
+	.battery_tmp_tbl	= zoom2_batt_table,
+	.tblsize		= ARRAY_SIZE(zoom2_batt_table),
+};
+
+static struct twl4030_usb_data zoom2_usb_data = {
+	.usb_mode	= T2_USB_MODE_ULPI,
 };
 
+static void __init omap_zoom2_init_irq(void)
+{
+	omap_board_config = zoom2_config;
+	omap_board_config_size = ARRAY_SIZE(zoom2_config);
+	omap2_init_common_hw(NULL, NULL);
+	omap_init_irq();
+	omap_gpio_init();
+}
+
 static struct twl4030_gpio_platform_data zoom2_gpio_data = {
 	.gpio_base	= OMAP_MAX_GPIO_LINES,
 	.irq_base	= TWL4030_GPIO_IRQ_BASE,
 	.irq_end	= TWL4030_GPIO_IRQ_END,
+	.setup		= zoom2_twl_gpio_setup,
+};
+
+static struct twl4030_madc_platform_data zoom2_madc_data = {
+	.irq_line	= 1,
 };
 
 static struct twl4030_platform_data zoom2_twldata = {
@@ -49,7 +230,15 @@ static struct twl4030_platform_data zoom2_twldata = {
 	.irq_end	= TWL4030_IRQ_END,
 
 	/* platform_data for children goes here */
+	.bci		= &zoom2_bci_data,
+	.madc		= &zoom2_madc_data,
+	.usb		= &zoom2_usb_data,
 	.gpio		= &zoom2_gpio_data,
+	.keypad		= &zoom2_kp_twl4030_data,
+	.vmmc1          = &zoom2_vmmc1,
+	.vmmc2          = &zoom2_vmmc2,
+	.vsim           = &zoom2_vsim,
+
 };
 
 static struct i2c_board_info __initdata zoom2_i2c_boardinfo[] = {
@@ -70,26 +259,13 @@ static int __init omap_i2c_init(void)
 	return 0;
 }
 
-static struct twl4030_hsmmc_info mmc[] __initdata = {
-	{
-		.mmc		= 1,
-		.wires		= 4,
-		.gpio_cd	= -EINVAL,
-		.gpio_wp	= -EINVAL,
-	},
-	{}	/* Terminator */
-};
-
 extern int __init omap_zoom2_debugboard_init(void);
 
 static void __init omap_zoom2_init(void)
 {
 	omap_i2c_init();
-	omap_board_config = zoom2_config;
-	omap_board_config_size = ARRAY_SIZE(zoom2_config);
 	omap_serial_init();
 	omap_zoom2_debugboard_init();
-	twl4030_mmc_init(mmc);
 	usb_musb_init();
 }
 

arch/arm/mach-omap2/clock.c

@@ -1043,5 +1043,7 @@ void omap2_clk_disable_unused(struct clk *clk)
 		omap2_clk_disable(clk);
 	} else
 		_omap2_clk_disable(clk);
+	if (clk->clkdm != NULL)
+		pwrdm_clkdm_state_switch(clk->clkdm);
 }
 #endif

arch/arm/mach-omap2/clock34xx.c

@@ -27,6 +27,7 @@
 #include <linux/limits.h>
 #include <linux/bitops.h>
 
+#include <mach/cpu.h>
 #include <mach/clock.h>
 #include <mach/sram.h>
 #include <asm/div64.h>
@@ -1067,17 +1068,17 @@ static int __init omap2_clk_arch_init(void)
 		return -EINVAL;
 
 	/* REVISIT: not yet ready for 343x */
-#if 0
-	if (clk_set_rate(&virt_prcm_set, mpurate))
-		printk(KERN_ERR "Could not find matching MPU rate\n");
-#endif
+	if (clk_set_rate(&dpll1_ck, mpurate))
+		printk(KERN_ERR "*** Unable to set MPU rate\n");
 
 	recalculate_root_clocks();
 
-	printk(KERN_INFO "Switched to new clocking rate (Crystal/DPLL3/MPU): "
+	printk(KERN_INFO "Switched to new clocking rate (Crystal/Core/MPU): "
 	       "%ld.%01ld/%ld/%ld MHz\n",
-	       (osc_sys_ck.rate / 1000000), (osc_sys_ck.rate / 100000) % 10,
-	       (core_ck.rate / 1000000), (dpll1_fck.rate / 1000000)) ;
+	       (osc_sys_ck.rate / 1000000), ((osc_sys_ck.rate / 100000) % 10),
+	       (core_ck.rate / 1000000), (arm_fck.rate / 1000000)) ;
+
+	calibrate_delay();
 
 	return 0;
 }
@@ -1136,7 +1137,7 @@ int __init omap2_clk_init(void)
 
 	recalculate_root_clocks();
 
-	printk(KERN_INFO "Clocking rate (Crystal/DPLL/ARM core): "
+	printk(KERN_INFO "Clocking rate (Crystal/Core/MPU): "
 	       "%ld.%01ld/%ld/%ld MHz\n",
 	       (osc_sys_ck.rate / 1000000), (osc_sys_ck.rate / 100000) % 10,
 	       (core_ck.rate / 1000000), (arm_fck.rate / 1000000));

arch/arm/mach-omap2/clock34xx.h

@@ -1020,6 +1020,7 @@ static struct clk arm_fck = {
 	.clksel_reg	= OMAP_CM_REGADDR(MPU_MOD, OMAP3430_CM_IDLEST_PLL),
 	.clksel_mask	= OMAP3430_ST_MPU_CLK_MASK,
 	.clksel		= arm_fck_clksel,
+	.clkdm_name	= "mpu_clkdm",
 	.recalc		= &omap2_clksel_recalc,
 };
 
@@ -1155,7 +1156,6 @@ static struct clk gfx_cg1_ck = {
 	.name		= "gfx_cg1_ck",
 	.ops		= &clkops_omap2_dflt_wait,
 	.parent		= &gfx_l3_fck, /* REVISIT: correct? */
-	.init		= &omap2_init_clk_clkdm,
 	.enable_reg	= OMAP_CM_REGADDR(GFX_MOD, CM_FCLKEN),
 	.enable_bit	= OMAP3430ES1_EN_2D_SHIFT,
 	.clkdm_name	= "gfx_3430es1_clkdm",
@@ -1166,7 +1166,6 @@ static struct clk gfx_cg2_ck = {
 	.name		= "gfx_cg2_ck",
 	.ops		= &clkops_omap2_dflt_wait,
 	.parent		= &gfx_l3_fck, /* REVISIT: correct? */
-	.init		= &omap2_init_clk_clkdm,
 	.enable_reg	= OMAP_CM_REGADDR(GFX_MOD, CM_FCLKEN),
 	.enable_bit	= OMAP3430ES1_EN_3D_SHIFT,
 	.clkdm_name	= "gfx_3430es1_clkdm",
@@ -1210,7 +1209,6 @@ static struct clk sgx_ick = {
 	.name		= "sgx_ick",
 	.ops		= &clkops_omap2_dflt_wait,
 	.parent		= &l3_ick,
-	.init		= &omap2_init_clk_clkdm,
 	.enable_reg	= OMAP_CM_REGADDR(OMAP3430ES2_SGX_MOD, CM_ICLKEN),
 	.enable_bit	= OMAP3430ES2_CM_ICLKEN_SGX_EN_SGX_SHIFT,
 	.clkdm_name	= "sgx_clkdm",
@@ -1223,7 +1221,6 @@ static struct clk d2d_26m_fck = {
 	.name		= "d2d_26m_fck",
 	.ops		= &clkops_omap2_dflt_wait,
 	.parent		= &sys_ck,
-	.init		= &omap2_init_clk_clkdm,
 	.enable_reg	= OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1),
 	.enable_bit	= OMAP3430ES1_EN_D2D_SHIFT,
 	.clkdm_name	= "d2d_clkdm",
@@ -1234,7 +1231,6 @@ static struct clk modem_fck = {
 	.name		= "modem_fck",
 	.ops		= &clkops_omap2_dflt_wait,
 	.parent		= &sys_ck,
-	.init		= &omap2_init_clk_clkdm,
 	.enable_reg	= OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1),
 	.enable_bit	= OMAP3430_EN_MODEM_SHIFT,
 	.clkdm_name	= "d2d_clkdm",
@@ -1622,7 +1618,6 @@ static struct clk core_l3_ick = {
 	.name		= "core_l3_ick",
 	.ops		= &clkops_null,
 	.parent		= &l3_ick,
-	.init		= &omap2_init_clk_clkdm,
 	.clkdm_name	= "core_l3_clkdm",
 	.recalc		= &followparent_recalc,
 };
@@ -1691,7 +1686,6 @@ static struct clk core_l4_ick = {
 	.name		= "core_l4_ick",
 	.ops		= &clkops_null,
 	.parent		= &l4_ick,
-	.init		= &omap2_init_clk_clkdm,
 	.clkdm_name	= "core_l4_clkdm",
 	.recalc		= &followparent_recalc,
 };
@@ -2089,7 +2083,6 @@ static struct clk dss_tv_fck = {
 	.name		= "dss_tv_fck",
 	.ops		= &clkops_omap2_dflt,
 	.parent		= &omap_54m_fck,
-	.init		= &omap2_init_clk_clkdm,
 	.enable_reg	= OMAP_CM_REGADDR(OMAP3430_DSS_MOD, CM_FCLKEN),
 	.enable_bit	= OMAP3430_EN_TV_SHIFT,
 	.clkdm_name	= "dss_clkdm",
@@ -2100,7 +2093,6 @@ static struct clk dss_96m_fck = {
 	.name		= "dss_96m_fck",
 	.ops		= &clkops_omap2_dflt,
 	.parent		= &omap_96m_fck,
-	.init		= &omap2_init_clk_clkdm,
 	.enable_reg	= OMAP_CM_REGADDR(OMAP3430_DSS_MOD, CM_FCLKEN),
 	.enable_bit	= OMAP3430_EN_TV_SHIFT,
 	.clkdm_name	= "dss_clkdm",
@@ -2111,7 +2103,6 @@ static struct clk dss2_alwon_fck = {
 	.name		= "dss2_alwon_fck",
 	.ops		= &clkops_omap2_dflt,
 	.parent		= &sys_ck,
-	.init		= &omap2_init_clk_clkdm,
 	.enable_reg	= OMAP_CM_REGADDR(OMAP3430_DSS_MOD, CM_FCLKEN),
 	.enable_bit	= OMAP3430_EN_DSS2_SHIFT,
 	.clkdm_name	= "dss_clkdm",
@@ -2123,7 +2114,6 @@ static struct clk dss_ick_3430es1 = {
 	.name		= "dss_ick",
 	.ops		= &clkops_omap2_dflt,
 	.parent		= &l4_ick,
-	.init		= &omap2_init_clk_clkdm,
 	.enable_reg	= OMAP_CM_REGADDR(OMAP3430_DSS_MOD, CM_ICLKEN),
 	.enable_bit	= OMAP3430_CM_ICLKEN_DSS_EN_DSS_SHIFT,
 	.clkdm_name	= "dss_clkdm",
@@ -2135,7 +2125,6 @@ static struct clk dss_ick_3430es2 = {
 	.name		= "dss_ick",
 	.ops		= &clkops_omap3430es2_dss_usbhost_wait,
 	.parent		= &l4_ick,
-	.init		= &omap2_init_clk_clkdm,
 	.enable_reg	= OMAP_CM_REGADDR(OMAP3430_DSS_MOD, CM_ICLKEN),
 	.enable_bit	= OMAP3430_CM_ICLKEN_DSS_EN_DSS_SHIFT,
 	.clkdm_name	= "dss_clkdm",
@@ -2159,7 +2148,6 @@ static struct clk cam_ick = {
 	.name		= "cam_ick",
 	.ops		= &clkops_omap2_dflt,
 	.parent		= &l4_ick,
-	.init		= &omap2_init_clk_clkdm,
 	.enable_reg	= OMAP_CM_REGADDR(OMAP3430_CAM_MOD, CM_ICLKEN),
 	.enable_bit	= OMAP3430_EN_CAM_SHIFT,
 	.clkdm_name	= "cam_clkdm",
@@ -2170,7 +2158,6 @@ static struct clk csi2_96m_fck = {
 	.name		= "csi2_96m_fck",
 	.ops		= &clkops_omap2_dflt,
 	.parent		= &core_96m_fck,
-	.init		= &omap2_init_clk_clkdm,
 	.enable_reg	= OMAP_CM_REGADDR(OMAP3430_CAM_MOD, CM_FCLKEN),
 	.enable_bit	= OMAP3430_EN_CSI2_SHIFT,
 	.clkdm_name	= "cam_clkdm",
@@ -2183,7 +2170,6 @@ static struct clk usbhost_120m_fck = {
 	.name		= "usbhost_120m_fck",
 	.ops		= &clkops_omap2_dflt,
 	.parent		= &dpll5_m2_ck,
-	.init		= &omap2_init_clk_clkdm,
 	.enable_reg	= OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_FCLKEN),
 	.enable_bit	= OMAP3430ES2_EN_USBHOST2_SHIFT,
 	.clkdm_name	= "usbhost_clkdm",
@@ -2194,7 +2180,6 @@ static struct clk usbhost_48m_fck = {
 	.name		= "usbhost_48m_fck",
 	.ops		= &clkops_omap3430es2_dss_usbhost_wait,
 	.parent		= &omap_48m_fck,
-	.init		= &omap2_init_clk_clkdm,
 	.enable_reg	= OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_FCLKEN),
 	.enable_bit	= OMAP3430ES2_EN_USBHOST1_SHIFT,
 	.clkdm_name	= "usbhost_clkdm",
@@ -2206,7 +2191,6 @@ static struct clk usbhost_ick = {
 	.name		= "usbhost_ick",
 	.ops		= &clkops_omap3430es2_dss_usbhost_wait,
 	.parent		= &l4_ick,
-	.init		= &omap2_init_clk_clkdm,
 	.enable_reg	= OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_ICLKEN),
 	.enable_bit	= OMAP3430ES2_EN_USBHOST_SHIFT,
 	.clkdm_name	= "usbhost_clkdm",
@@ -2268,7 +2252,6 @@ static struct clk gpt1_fck = {
 static struct clk wkup_32k_fck = {
 	.name		= "wkup_32k_fck",
 	.ops		= &clkops_null,
-	.init		= &omap2_init_clk_clkdm,
 	.parent		= &omap_32k_fck,
 	.clkdm_name	= "wkup_clkdm",
 	.recalc		= &followparent_recalc,
@@ -2383,7 +2366,6 @@ static struct clk per_96m_fck = {
 	.name		= "per_96m_fck",
 	.ops		= &clkops_null,
 	.parent		= &omap_96m_alwon_fck,
-	.init		= &omap2_init_clk_clkdm,
 	.clkdm_name	= "per_clkdm",
 	.recalc		= &followparent_recalc,
 };
@@ -2392,7 +2374,6 @@ static struct clk per_48m_fck = {
 	.name		= "per_48m_fck",
 	.ops		= &clkops_null,
 	.parent		= &omap_48m_fck,
-	.init		= &omap2_init_clk_clkdm,
 	.clkdm_name	= "per_clkdm",
 	.recalc		= &followparent_recalc,
 };

arch/arm/mach-omap2/clockdomain.c

@@ -299,7 +299,8 @@ struct clockdomain *clkdm_lookup(const char *name)
  * anything else to indicate failure; or -EINVAL if the function pointer
  * is null.
  */
-int clkdm_for_each(int (*fn)(struct clockdomain *clkdm))
+int clkdm_for_each(int (*fn)(struct clockdomain *clkdm, void *user),
+			void *user)
 {
 	struct clockdomain *clkdm;
 	int ret = 0;
@@ -309,7 +310,7 @@ int clkdm_for_each(int (*fn)(struct clockdomain *clkdm))
 
 	mutex_lock(&clkdm_mutex);
 	list_for_each_entry(clkdm, &clkdm_list, node) {
-		ret = (*fn)(clkdm);
+		ret = (*fn)(clkdm, user);
 		if (ret)
 			break;
 	}
@@ -484,6 +485,8 @@ void omap2_clkdm_allow_idle(struct clockdomain *clkdm)
 			    v << __ffs(clkdm->clktrctrl_mask),
 			    clkdm->pwrdm.ptr->prcm_offs,
 			    CM_CLKSTCTRL);
+
+	pwrdm_clkdm_state_switch(clkdm);
 }
 
 /**
@@ -572,6 +575,7 @@ int omap2_clkdm_clk_enable(struct clockdomain *clkdm, struct clk *clk)
 		omap2_clkdm_wakeup(clkdm);
 
 	pwrdm_wait_transition(clkdm->pwrdm.ptr);
+	pwrdm_clkdm_state_switch(clkdm);
 
 	return 0;
 }
@@ -624,6 +628,8 @@ int omap2_clkdm_clk_disable(struct clockdomain *clkdm, struct clk *clk)
 	else
 		omap2_clkdm_sleep(clkdm);
 
+	pwrdm_clkdm_state_switch(clkdm);
+
 	return 0;
 }
 

arch/arm/mach-omap2/cm.c

+/*
+ * OMAP2/3 CM module functions
+ *
+ * Copyright (C) 2009 Nokia Corporation
+ * Paul Walmsley
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/delay.h>
+#include <linux/spinlock.h>
+#include <linux/list.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/io.h>
+
+#include <asm/atomic.h>
+
+#include "cm.h"
+#include "cm-regbits-24xx.h"
+#include "cm-regbits-34xx.h"
+
+/* MAX_MODULE_READY_TIME: max milliseconds for module to leave idle */
+#define MAX_MODULE_READY_TIME		20000
+
+static const u8 cm_idlest_offs[] = {
+	CM_IDLEST1, CM_IDLEST2, OMAP2430_CM_IDLEST3
+};
+
+/**
+ * omap2_cm_wait_idlest_ready - wait for a module to leave idle or standby
+ * @prcm_mod: PRCM module offset
+ * @idlest_id: CM_IDLESTx register ID (i.e., x = 1, 2, 3)
+ * @idlest_shift: shift of the bit in the CM_IDLEST* register to check
+ *
+ * XXX document
+ */
+int omap2_cm_wait_module_ready(s16 prcm_mod, u8 idlest_id, u8 idlest_shift)
+{
+	int ena = 0, i = 0;
+	u8 cm_idlest_reg;
+	u32 mask;
+
+	if (!idlest_id || (idlest_id > ARRAY_SIZE(cm_idlest_offs)))
+		return -EINVAL;
+
+	cm_idlest_reg = cm_idlest_offs[idlest_id - 1];
+
+	if (cpu_is_omap24xx())
+		ena = idlest_shift;
+	else if (cpu_is_omap34xx())
+		ena = 0;
+	else
+		BUG();
+
+	mask = 1 << idlest_shift;
+
+	/* XXX should be OMAP2 CM */
+	while (((cm_read_mod_reg(prcm_mod, cm_idlest_reg) & mask) != ena) &&
+	       (i++ < MAX_MODULE_READY_TIME))
+		udelay(1);
+
+	return (i < MAX_MODULE_READY_TIME) ? 0 : -EBUSY;
+}
+

arch/arm/mach-omap2/cm.h

@@ -17,11 +17,11 @@
 #include "prcm-common.h"
 
 #define OMAP2420_CM_REGADDR(module, reg)				\
-			IO_ADDRESS(OMAP2420_CM_BASE + (module) + (reg))
+			OMAP2_IO_ADDRESS(OMAP2420_CM_BASE + (module) + (reg))
 #define OMAP2430_CM_REGADDR(module, reg)				\
-			IO_ADDRESS(OMAP2430_CM_BASE + (module) + (reg))
+			OMAP2_IO_ADDRESS(OMAP2430_CM_BASE + (module) + (reg))
 #define OMAP34XX_CM_REGADDR(module, reg)				\
-			IO_ADDRESS(OMAP3430_CM_BASE + (module) + (reg))
+			OMAP2_IO_ADDRESS(OMAP3430_CM_BASE + (module) + (reg))
 
 /*
  * Architecture-specific global CM registers
@@ -98,6 +98,10 @@ extern u32 cm_read_mod_reg(s16 module, u16 idx);
 extern void cm_write_mod_reg(u32 val, s16 module, u16 idx);
 extern u32 cm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module, s16 idx);
 
+extern int omap2_cm_wait_module_ready(s16 prcm_mod, u8 idlest_id,
+				      u8 idlest_shift);
+extern int omap4_cm_wait_module_ready(u32 prcm_mod, u8 prcm_dev_offs);
+
 static inline u32 cm_set_mod_reg_bits(u32 bits, s16 module, s16 idx)
 {
 	return cm_rmw_mod_reg_bits(bits, bits, module, idx);

arch/arm/mach-omap2/cm4xxx.c

+/*
+ * OMAP4 CM module functions
+ *
+ * Copyright (C) 2009 Nokia Corporation
+ * Paul Walmsley
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/delay.h>
+#include <linux/spinlock.h>
+#include <linux/list.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/io.h>
+
+#include <asm/atomic.h>
+
+#include "cm.h"
+#include "cm-regbits-4xxx.h"
+
+/* XXX move this to cm.h */
+/* MAX_MODULE_READY_TIME: max milliseconds for module to leave idle */
+#define MAX_MODULE_READY_TIME			20000
+
+/*
+ * OMAP4_PRCM_CM_CLKCTRL_IDLEST_MASK: isolates the IDLEST field in the
+ * CM_CLKCTRL register.
+ */
+#define OMAP4_PRCM_CM_CLKCTRL_IDLEST_MASK	(0x2 << 16)
+
+/*
+ * OMAP4 prcm_mod u32 fields contain packed data: the CM ID in bit 16 and
+ * the PRCM module offset address (from the CM module base) in bits 15-0.
+ */
+#define OMAP4_PRCM_MOD_CM_ID_SHIFT		16
+#define OMAP4_PRCM_MOD_OFFS_MASK		0xffff
+
+/**
+ * omap4_cm_wait_idlest_ready - wait for a module to leave idle or standby
+ * @prcm_mod: PRCM module offset (XXX example)
+ * @prcm_dev_offs: PRCM device offset (e.g. MCASP XXX example)
+ *
+ * XXX document
+ */
+int omap4_cm_wait_idlest_ready(u32 prcm_mod, u8 prcm_dev_offs)
+{
+	int i = 0;
+	u8 cm_id;
+	u16 prcm_mod_offs;
+	u32 mask = OMAP4_PRCM_CM_CLKCTRL_IDLEST_MASK;
+
+	cm_id = prcm_mod >> OMAP4_PRCM_MOD_CM_ID_SHIFT;
+	prcm_mod_offs = prcm_mod & OMAP4_PRCM_MOD_OFFS_MASK;
+
+	while (((omap4_cm_read_mod_reg(cm_id, prcm_mod_offs, prcm_dev_offs,
+				       OMAP4_CM_CLKCTRL_DREG) & mask) != 0) &&
+	       (i++ < MAX_MODULE_READY_TIME))
+		udelay(1);
+
+	return (i < MAX_MODULE_READY_TIME) ? 0 : -EBUSY;
+}
+

arch/arm/mach-omap2/devices.c

@@ -513,6 +513,47 @@ static inline void omap2_mmc_mux(struct omap_mmc_platform_data *mmc_controller,
 			omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0);
 		}
 	}
+
+	if (cpu_is_omap3430()) {
+		if (controller_nr == 0) {
+			omap_cfg_reg(N28_3430_MMC1_CLK);
+			omap_cfg_reg(M27_3430_MMC1_CMD);
+			omap_cfg_reg(N27_3430_MMC1_DAT0);
+			if (mmc_controller->slots[0].wires == 4 ||
+				mmc_controller->slots[0].wires == 8) {
+				omap_cfg_reg(N26_3430_MMC1_DAT1);
+				omap_cfg_reg(N25_3430_MMC1_DAT2);
+				omap_cfg_reg(P28_3430_MMC1_DAT3);
+			}
+			if (mmc_controller->slots[0].wires == 8) {
+				omap_cfg_reg(P27_3430_MMC1_DAT4);
+				omap_cfg_reg(P26_3430_MMC1_DAT5);
+				omap_cfg_reg(R27_3430_MMC1_DAT6);
+				omap_cfg_reg(R25_3430_MMC1_DAT7);
+			}
+		}
+		if (controller_nr == 1) {
+			/* MMC2 */
+			omap_cfg_reg(AE2_3430_MMC2_CLK);
+			omap_cfg_reg(AG5_3430_MMC2_CMD);
+			omap_cfg_reg(AH5_3430_MMC2_DAT0);
+
+			/*
+			 * For 8 wire configurations, Lines DAT4, 5, 6 and 7 need to be muxed
+			 * in the board-*.c files
+			 */
+			if (mmc_controller->slots[0].wires == 4 ||
+				mmc_controller->slots[0].wires == 8) {
+				omap_cfg_reg(AH4_3430_MMC2_DAT1);
+				omap_cfg_reg(AG4_3430_MMC2_DAT2);
+				omap_cfg_reg(AF4_3430_MMC2_DAT3);
+			}
+		}
+
+		/*
+		 * For MMC3 the pins need to be muxed in the board-*.c files
+		 */
+	}
 }
 
 void __init omap2_init_mmc(struct omap_mmc_platform_data **mmc_data,

arch/arm/mach-omap2/io.c

@@ -32,17 +32,23 @@
 #include <mach/sram.h>
 #include <mach/sdrc.h>
 #include <mach/gpmc.h>
+#include <mach/serial.h>
 
 #ifndef CONFIG_ARCH_OMAP4	/* FIXME: Remove this once clkdev is ready */
 #include "clock.h"
 
+#include <mach/omap-pm.h>
 #include <mach/powerdomain.h>
-
 #include "powerdomains.h"
 
 #include <mach/clockdomain.h>
 #include "clockdomains.h"
 #endif
+#include <mach/omap_hwmod.h>
+#include "omap_hwmod_2420.h"
+#include "omap_hwmod_2430.h"
+#include "omap_hwmod_34xx.h"
+
 /*
  * The machine specific code may provide the extra mapping besides the
  * default mapping provided here.
@@ -279,11 +285,26 @@ static int __init _omap2_init_reprogram_sdrc(void)
 void __init omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0,
 				 struct omap_sdrc_params *sdrc_cs1)
 {
+	struct omap_hwmod **hwmods = NULL;
+
+	if (cpu_is_omap2420())
+		hwmods = omap2420_hwmods;
+	else if (cpu_is_omap2430())
+		hwmods = omap2430_hwmods;
+	else if (cpu_is_omap34xx())
+		hwmods = omap34xx_hwmods;
+
+	omap_hwmod_init(hwmods);
 	omap2_mux_init();
 #ifndef CONFIG_ARCH_OMAP4 /* FIXME: Remove this once the clkdev is ready */
+	/* The OPP tables have to be registered before a clk init */
+	omap_pm_if_early_init(mpu_opps, dsp_opps, l3_opps);
 	pwrdm_init(powerdomains_omap);
 	clkdm_init(clockdomains_omap, clkdm_pwrdm_autodeps);
 	omap2_clk_init();
+	omap_serial_early_init();
+	omap_hwmod_late_init();
+	omap_pm_if_init();
 	omap2_sdrc_init(sdrc_cs0, sdrc_cs1);
 	_omap2_init_reprogram_sdrc();
 #endif

arch/arm/mach-omap2/iommu2.c

@@ -217,10 +217,19 @@ static ssize_t omap2_dump_cr(struct iommu *obj, struct cr_regs *cr, char *buf)
 }
 
 #define pr_reg(name)							\
-	p += sprintf(p, "%20s: %08x\n",					\
-		     __stringify(name), iommu_read_reg(obj, MMU_##name));
-
-static ssize_t omap2_iommu_dump_ctx(struct iommu *obj, char *buf)
+	do {								\
+		ssize_t bytes;						\
+		const char *str = "%20s: %08x\n";			\
+		const int maxcol = 32;					\
+		bytes = snprintf(p, maxcol, str, __stringify(name),	\
+				 iommu_read_reg(obj, MMU_##name));	\
+		p += bytes;						\
+		len -= bytes;						\
+		if (len < maxcol)					\
+			goto out;					\
+	} while (0)
+
+static ssize_t omap2_iommu_dump_ctx(struct iommu *obj, char *buf, ssize_t len)
 {
 	char *p = buf;
 
@@ -242,7 +251,7 @@ static ssize_t omap2_iommu_dump_ctx(struct iommu *obj, char *buf)
 	pr_reg(READ_CAM);
 	pr_reg(READ_RAM);
 	pr_reg(EMU_FAULT_AD);
-
+out:
 	return p - buf;
 }
 

arch/arm/mach-omap2/mux.c

@@ -492,6 +492,61 @@ MUX_CFG_34XX("H16_34XX_SDRC_CKE0", 0x262,
 		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
 MUX_CFG_34XX("H17_34XX_SDRC_CKE1", 0x264,
 		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
+
+/* MMC1 */
+MUX_CFG_34XX("N28_3430_MMC1_CLK", 0x144,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("M27_3430_MMC1_CMD", 0x146,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("N27_3430_MMC1_DAT0", 0x148,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("N26_3430_MMC1_DAT1", 0x14a,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("N25_3430_MMC1_DAT2", 0x14c,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("P28_3430_MMC1_DAT3", 0x14e,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("P27_3430_MMC1_DAT4", 0x150,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("P26_3430_MMC1_DAT5", 0x152,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("R27_3430_MMC1_DAT6", 0x154,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("R25_3430_MMC1_DAT7", 0x156,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLUP)
+
+/* MMC2 */
+MUX_CFG_34XX("AE2_3430_MMC2_CLK", 0x158,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("AG5_3430_MMC2_CMD", 0x15A,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("AH5_3430_MMC2_DAT0", 0x15c,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("AH4_3430_MMC2_DAT1", 0x15e,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("AG4_3430_MMC2_DAT2", 0x160,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("AF4_3430_MMC2_DAT3", 0x162,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_INPUT_PULLUP)
+
+/* MMC3 */
+MUX_CFG_34XX("AF10_3430_MMC3_CLK", 0x5d8,
+		OMAP34XX_MUX_MODE2 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("AC3_3430_MMC3_CMD", 0x1d0,
+		OMAP34XX_MUX_MODE3 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("AE11_3430_MMC3_DAT0", 0x5e4,
+		OMAP34XX_MUX_MODE2 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("AH9_3430_MMC3_DAT1", 0x5e6,
+		OMAP34XX_MUX_MODE2 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("AF13_3430_MMC3_DAT2", 0x5e8,
+		OMAP34XX_MUX_MODE2 | OMAP34XX_PIN_INPUT_PULLUP)
+MUX_CFG_34XX("AF13_3430_MMC3_DAT3", 0x5e2,
+		OMAP34XX_MUX_MODE2 | OMAP34XX_PIN_INPUT_PULLUP)
+
+/* SYS_NIRQ T2 INT1 */
+MUX_CFG_34XX("AF26_34XX_SYS_NIRQ", 0x1E0,
+		OMAP3_WAKEUP_EN | OMAP34XX_PIN_INPUT_PULLUP |
+		OMAP34XX_MUX_MODE0)
 };
 
 #define OMAP34XX_PINS_SZ	ARRAY_SIZE(omap34xx_pins)

arch/arm/mach-omap2/omap-smp.c

@@ -54,7 +54,7 @@ void __cpuinit platform_secondary_init(unsigned int cpu)
 	 * for us: do so
 	 */
 
-	gic_cpu_init(0, IO_ADDRESS(OMAP44XX_GIC_CPU_BASE));
+	gic_cpu_init(0, OMAP2_IO_ADDRESS(OMAP44XX_GIC_CPU_BASE));
 
 	/*
 	 * Synchronise with the boot thread.

arch/arm/mach-omap2/omap_hwmod_2420.h

+/*
+ * omap_hwmod_2420.h - hardware modules present on the OMAP2420 chips
+ *
+ * Copyright (C) 2009 Nokia Corporation
+ * Paul Walmsley
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * XXX handle crossbar/shared link difference for L3?
+ *
+ */
+#ifndef __ARCH_ARM_PLAT_OMAP_INCLUDE_MACH_OMAP_HWMOD2420_H
+#define __ARCH_ARM_PLAT_OMAP_INCLUDE_MACH_OMAP_HWMOD2420_H
+
+#ifdef CONFIG_ARCH_OMAP2420
+
+#include <mach/omap_hwmod.h>
+#include <mach/irqs.h>
+#include <mach/cpu.h>
+#include <mach/dma.h>
+
+#include "prm-regbits-24xx.h"
+
+static struct omap_hwmod omap2420_mpu_hwmod;
+static struct omap_hwmod omap2420_l3_hwmod;
+static struct omap_hwmod omap2420_l4_core_hwmod;
+
+/* L3 -> L4_CORE interface */
+static struct omap_hwmod_ocp_if omap2420_l3__l4_core = {
+	.master	= &omap2420_l3_hwmod,
+	.slave	= &omap2420_l4_core_hwmod,
+	.user	= OCP_USER_MPU | OCP_USER_SDMA,
+};
+
+/* MPU -> L3 interface */
+static struct omap_hwmod_ocp_if omap2420_mpu__l3 = {
+	.master = &omap2420_mpu_hwmod,
+	.slave	= &omap2420_l3_hwmod,
+	.user	= OCP_USER_MPU,
+};
+
+/* Slave interfaces on the L3 interconnect */
+static struct omap_hwmod_ocp_if *omap2420_l3_slaves[] = {
+	&omap2420_mpu__l3,
+};
+
+/* Master interfaces on the L3 interconnect */
+static struct omap_hwmod_ocp_if *omap2420_l3_masters[] = {
+	&omap2420_l3__l4_core,
+};
+
+/* L3 */
+static struct omap_hwmod omap2420_l3_hwmod = {
+	.name		= "l3_hwmod",
+	.masters	= omap2420_l3_masters,
+	.masters_cnt	= ARRAY_SIZE(omap2420_l3_masters),
+	.slaves		= omap2420_l3_slaves,
+	.slaves_cnt	= ARRAY_SIZE(omap2420_l3_slaves),
+	.omap_chip	= OMAP_CHIP_INIT(CHIP_IS_OMAP2420)
+};
+
+static struct omap_hwmod omap2420_l4_wkup_hwmod;
+
+/* L4_CORE -> L4_WKUP interface */
+static struct omap_hwmod_ocp_if omap2420_l4_core__l4_wkup = {
+	.master	= &omap2420_l4_core_hwmod,
+	.slave	= &omap2420_l4_wkup_hwmod,
+	.user	= OCP_USER_MPU | OCP_USER_SDMA,
+};
+
+/* Slave interfaces on the L4_CORE interconnect */
+static struct omap_hwmod_ocp_if *omap2420_l4_core_slaves[] = {
+	&omap2420_l3__l4_core,
+};
+
+/* Master interfaces on the L4_CORE interconnect */
+static struct omap_hwmod_ocp_if *omap2420_l4_core_masters[] = {
+	&omap2420_l4_core__l4_wkup,
+};
+
+/* L4 CORE */
+static struct omap_hwmod omap2420_l4_core_hwmod = {
+	.name		= "l4_core_hwmod",
+	.masters	= omap2420_l4_core_masters,
+	.masters_cnt	= ARRAY_SIZE(omap2420_l4_core_masters),
+	.slaves		= omap2420_l4_core_slaves,
+	.slaves_cnt	= ARRAY_SIZE(omap2420_l4_core_slaves),
+	.omap_chip	= OMAP_CHIP_INIT(CHIP_IS_OMAP2420)
+};
+
+/* Slave interfaces on the L4_WKUP interconnect */
+static struct omap_hwmod_ocp_if *omap2420_l4_wkup_slaves[] = {
+	&omap2420_l4_core__l4_wkup,
+};
+
+/* Master interfaces on the L4_WKUP interconnect */
+static struct omap_hwmod_ocp_if *omap2420_l4_wkup_masters[] = {
+};
+
+/* L4 WKUP */
+static struct omap_hwmod omap2420_l4_wkup_hwmod = {
+	.name		= "l4_wkup_hwmod",
+	.masters	= omap2420_l4_wkup_masters,
+	.masters_cnt	= ARRAY_SIZE(omap2420_l4_wkup_masters),
+	.slaves		= omap2420_l4_wkup_slaves,
+	.slaves_cnt	= ARRAY_SIZE(omap2420_l4_wkup_slaves),
+	.omap_chip	= OMAP_CHIP_INIT(CHIP_IS_OMAP2420)
+};
+
+/* Master interfaces on the MPU device */
+static struct omap_hwmod_ocp_if *omap2420_mpu_masters[] = {
+	&omap2420_mpu__l3,
+};
+
+/* MPU */
+static struct omap_hwmod omap2420_mpu_hwmod = {
+	.name		= "mpu_hwmod",
+	.clkdev_dev_id	= NULL,
+	.clkdev_con_id	= "mpu_ck",
+	.masters	= omap2420_mpu_masters,
+	.masters_cnt	= ARRAY_SIZE(omap2420_mpu_masters),
+	.omap_chip	= OMAP_CHIP_INIT(CHIP_IS_OMAP2420),
+};
+
+static __initdata struct omap_hwmod *omap2420_hwmods[] = {
+	&omap2420_l3_hwmod,
+	&omap2420_l4_core_hwmod,
+	&omap2420_l4_wkup_hwmod,
+	&omap2420_mpu_hwmod,
+	NULL,
+};
+
+#else
+# define omap2420_hwmods		0
+#endif
+
+#endif
+
+

arch/arm/mach-omap2/omap_hwmod_2430.h

+/*
+ * omap_hwmod_2430.h - hardware modules present on the OMAP2430 chips
+ *
+ * Copyright (C) 2009 Nokia Corporation
+ * Paul Walmsley
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * XXX handle crossbar/shared link difference for L3?
+ *
+ */
+#ifndef __ARCH_ARM_PLAT_OMAP_INCLUDE_MACH_OMAP_HWMOD2430_H
+#define __ARCH_ARM_PLAT_OMAP_INCLUDE_MACH_OMAP_HWMOD2430_H
+
+#ifdef CONFIG_ARCH_OMAP2430
+
+#include <mach/omap_hwmod.h>
+#include <mach/irqs.h>
+#include <mach/cpu.h>
+#include <mach/dma.h>
+
+#include "prm-regbits-24xx.h"
+
+static struct omap_hwmod omap2430_mpu_hwmod;
+static struct omap_hwmod omap2430_l3_hwmod;
+static struct omap_hwmod omap2430_l4_core_hwmod;
+
+/* L3 -> L4_CORE interface */
+static struct omap_hwmod_ocp_if omap2430_l3__l4_core = {
+	.master	= &omap2430_l3_hwmod,
+	.slave	= &omap2430_l4_core_hwmod,
+	.user	= OCP_USER_MPU | OCP_USER_SDMA,
+};
+
+/* MPU -> L3 interface */
+static struct omap_hwmod_ocp_if omap2430_mpu__l3 = {
+	.master = &omap2430_mpu_hwmod,
+	.slave	= &omap2430_l3_hwmod,
+	.user	= OCP_USER_MPU,
+};
+
+/* Slave interfaces on the L3 interconnect */
+static struct omap_hwmod_ocp_if *omap2430_l3_slaves[] = {
+	&omap2430_mpu__l3,
+};
+
+/* Master interfaces on the L3 interconnect */
+static struct omap_hwmod_ocp_if *omap2430_l3_masters[] = {
+	&omap2430_l3__l4_core,
+};
+
+/* L3 */
+static struct omap_hwmod omap2430_l3_hwmod = {
+	.name		= "l3_hwmod",
+	.masters	= omap2430_l3_masters,
+	.masters_cnt	= ARRAY_SIZE(omap2430_l3_masters),
+	.slaves		= omap2430_l3_slaves,
+	.slaves_cnt	= ARRAY_SIZE(omap2430_l3_slaves),
+	.omap_chip	= OMAP_CHIP_INIT(CHIP_IS_OMAP2430)
+};
+
+static struct omap_hwmod omap2430_l4_wkup_hwmod;
+static struct omap_hwmod omap2430_mmc1_hwmod;
+static struct omap_hwmod omap2430_mmc2_hwmod;
+
+/* L4_CORE -> L4_WKUP interface */
+static struct omap_hwmod_ocp_if omap2430_l4_core__l4_wkup = {
+	.master	= &omap2430_l4_core_hwmod,
+	.slave	= &omap2430_l4_wkup_hwmod,
+	.user	= OCP_USER_MPU | OCP_USER_SDMA,
+};
+
+/* Slave interfaces on the L4_CORE interconnect */
+static struct omap_hwmod_ocp_if *omap2430_l4_core_slaves[] = {
+	&omap2430_l3__l4_core,
+};
+
+/* Master interfaces on the L4_CORE interconnect */
+static struct omap_hwmod_ocp_if *omap2430_l4_core_masters[] = {
+	&omap2430_l4_core__l4_wkup,
+};
+
+/* L4 CORE */
+static struct omap_hwmod omap2430_l4_core_hwmod = {
+	.name		= "l4_core_hwmod",
+	.masters	= omap2430_l4_core_masters,
+	.masters_cnt	= ARRAY_SIZE(omap2430_l4_core_masters),
+	.slaves		= omap2430_l4_core_slaves,
+	.slaves_cnt	= ARRAY_SIZE(omap2430_l4_core_slaves),
+	.omap_chip	= OMAP_CHIP_INIT(CHIP_IS_OMAP2430)
+};
+
+/* Slave interfaces on the L4_WKUP interconnect */
+static struct omap_hwmod_ocp_if *omap2430_l4_wkup_slaves[] = {
+	&omap2430_l4_core__l4_wkup,
+};
+
+/* Master interfaces on the L4_WKUP interconnect */
+static struct omap_hwmod_ocp_if *omap2430_l4_wkup_masters[] = {
+};
+
+/* L4 WKUP */
+static struct omap_hwmod omap2430_l4_wkup_hwmod = {
+	.name		= "l4_wkup_hwmod",
+	.masters	= omap2430_l4_wkup_masters,
+	.masters_cnt	= ARRAY_SIZE(omap2430_l4_wkup_masters),
+	.slaves		= omap2430_l4_wkup_slaves,
+	.slaves_cnt	= ARRAY_SIZE(omap2430_l4_wkup_slaves),
+	.omap_chip	= OMAP_CHIP_INIT(CHIP_IS_OMAP2430)
+};
+
+/* Master interfaces on the MPU device */
+static struct omap_hwmod_ocp_if *omap2430_mpu_masters[] = {
+	&omap2430_mpu__l3,
+};
+
+/* MPU */
+static struct omap_hwmod omap2430_mpu_hwmod = {
+	.name		= "mpu_hwmod",
+	.clkdev_dev_id	= NULL,
+	.clkdev_con_id	= "mpu_ck",
+	.masters	= omap2430_mpu_masters,
+	.masters_cnt	= ARRAY_SIZE(omap2430_mpu_masters),
+	.omap_chip	= OMAP_CHIP_INIT(CHIP_IS_OMAP2430),
+};
+
+static __initdata struct omap_hwmod *omap2430_hwmods[] = {
+	&omap2430_l3_hwmod,
+	&omap2430_l4_core_hwmod,
+	&omap2430_l4_wkup_hwmod,
+	&omap2430_mpu_hwmod,
+	NULL,
+};
+
+#else
+# define omap2430_hwmods		0
+#endif
+
+#endif
+
+

arch/arm/mach-omap2/omap_hwmod_34xx.h

+/*
+ * omap_hwmod_34xx.h - hardware modules present on the OMAP34xx chips
+ *
+ * Copyright (C) 2009 Nokia Corporation
+ * Paul Walmsley
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+#ifndef __ARCH_ARM_PLAT_OMAP_INCLUDE_MACH_OMAP_HWMOD34XX_H
+#define __ARCH_ARM_PLAT_OMAP_INCLUDE_MACH_OMAP_HWMOD34XX_H
+
+#ifdef CONFIG_ARCH_OMAP34XX
+
+#include <mach/omap_hwmod.h>
+#include <mach/irqs.h>
+#include <mach/cpu.h>
+#include <mach/dma.h>
+
+#include "prm-regbits-34xx.h"
+
+static struct omap_hwmod omap34xx_mpu_hwmod;
+static struct omap_hwmod omap34xx_l3_hwmod;
+static struct omap_hwmod omap34xx_l4_core_hwmod;
+static struct omap_hwmod omap34xx_l4_per_hwmod;
+
+/* L3 -> L4_CORE interface */
+static struct omap_hwmod_ocp_if omap34xx_l3__l4_core = {
+	.master	= &omap34xx_l3_hwmod,
+	.slave	= &omap34xx_l4_core_hwmod,
+	.user	= OCP_USER_MPU | OCP_USER_SDMA,
+};
+
+/* L3 -> L4_PER interface */
+static struct omap_hwmod_ocp_if omap34xx_l3__l4_per = {
+	.master = &omap34xx_l3_hwmod,
+	.slave	= &omap34xx_l4_per_hwmod,
+	.user	= OCP_USER_MPU | OCP_USER_SDMA,
+};
+
+/* MPU -> L3 interface */
+static struct omap_hwmod_ocp_if omap34xx_mpu__l3 = {
+	.master = &omap34xx_mpu_hwmod,
+	.slave	= &omap34xx_l3_hwmod,
+	.user	= OCP_USER_MPU,
+};
+
+/* Slave interfaces on the L3 interconnect */
+static struct omap_hwmod_ocp_if *omap34xx_l3_slaves[] = {
+	&omap34xx_mpu__l3,
+};
+
+/* Master interfaces on the L3 interconnect */
+static struct omap_hwmod_ocp_if *omap34xx_l3_masters[] = {
+	&omap34xx_l3__l4_core,
+	&omap34xx_l3__l4_per,
+};
+
+/* L3 */
+static struct omap_hwmod omap34xx_l3_hwmod = {
+	.name		= "l3_hwmod",
+	.masters	= omap34xx_l3_masters,
+	.masters_cnt	= ARRAY_SIZE(omap34xx_l3_masters),
+	.slaves		= omap34xx_l3_slaves,
+	.slaves_cnt	= ARRAY_SIZE(omap34xx_l3_slaves),
+	.omap_chip	= OMAP_CHIP_INIT(CHIP_IS_OMAP3430)
+};
+
+static struct omap_hwmod omap34xx_l4_wkup_hwmod;
+
+/* L4_CORE -> L4_WKUP interface */
+static struct omap_hwmod_ocp_if omap34xx_l4_core__l4_wkup = {
+	.master	= &omap34xx_l4_core_hwmod,
+	.slave	= &omap34xx_l4_wkup_hwmod,
+	.user	= OCP_USER_MPU | OCP_USER_SDMA,
+};
+
+/* Slave interfaces on the L4_CORE interconnect */
+static struct omap_hwmod_ocp_if *omap34xx_l4_core_slaves[] = {
+	&omap34xx_l3__l4_core,
+};
+
+/* Master interfaces on the L4_CORE interconnect */
+static struct omap_hwmod_ocp_if *omap34xx_l4_core_masters[] = {
+	&omap34xx_l4_core__l4_wkup,
+};
+
+/* L4 CORE */
+static struct omap_hwmod omap34xx_l4_core_hwmod = {
+	.name		= "l4_core_hwmod",
+	.masters	= omap34xx_l4_core_masters,
+	.masters_cnt	= ARRAY_SIZE(omap34xx_l4_core_masters),
+	.slaves		= omap34xx_l4_core_slaves,
+	.slaves_cnt	= ARRAY_SIZE(omap34xx_l4_core_slaves),
+	.omap_chip	= OMAP_CHIP_INIT(CHIP_IS_OMAP3430)
+};
+
+/* Slave interfaces on the L4_PER interconnect */
+static struct omap_hwmod_ocp_if *omap34xx_l4_per_slaves[] = {
+	&omap34xx_l3__l4_per,
+};
+
+/* Master interfaces on the L4_PER interconnect */
+static struct omap_hwmod_ocp_if *omap34xx_l4_per_masters[] = {
+};
+
+/* L4 PER */
+static struct omap_hwmod omap34xx_l4_per_hwmod = {
+	.name		= "l4_per_hwmod",
+	.masters	= omap34xx_l4_per_masters,
+	.masters_cnt	= ARRAY_SIZE(omap34xx_l4_per_masters),
+	.slaves		= omap34xx_l4_per_slaves,
+	.slaves_cnt	= ARRAY_SIZE(omap34xx_l4_per_slaves),
+	.omap_chip	= OMAP_CHIP_INIT(CHIP_IS_OMAP3430)
+};
+
+/* Slave interfaces on the L4_WKUP interconnect */
+static struct omap_hwmod_ocp_if *omap34xx_l4_wkup_slaves[] = {
+	&omap34xx_l4_core__l4_wkup,
+};
+
+/* Master interfaces on the L4_WKUP interconnect */
+static struct omap_hwmod_ocp_if *omap34xx_l4_wkup_masters[] = {
+};
+
+/* L4 WKUP */
+static struct omap_hwmod omap34xx_l4_wkup_hwmod = {
+	.name		= "l4_wkup_hwmod",
+	.masters	= omap34xx_l4_wkup_masters,
+	.masters_cnt	= ARRAY_SIZE(omap34xx_l4_wkup_masters),
+	.slaves		= omap34xx_l4_wkup_slaves,
+	.slaves_cnt	= ARRAY_SIZE(omap34xx_l4_wkup_slaves),
+	.omap_chip	= OMAP_CHIP_INIT(CHIP_IS_OMAP3430)
+};
+
+/* Master interfaces on the MPU device */
+static struct omap_hwmod_ocp_if *omap34xx_mpu_masters[] = {
+	&omap34xx_mpu__l3,
+};
+
+/* MPU */
+static struct omap_hwmod omap34xx_mpu_hwmod = {
+	.name		= "mpu_hwmod",
+	.clkdev_dev_id	= NULL,
+	.clkdev_con_id	= "arm_fck",
+	.masters	= omap34xx_mpu_masters,
+	.masters_cnt	= ARRAY_SIZE(omap34xx_mpu_masters),
+	.omap_chip	= OMAP_CHIP_INIT(CHIP_IS_OMAP3430),
+};
+
+static __initdata struct omap_hwmod *omap34xx_hwmods[] = {
+	&omap34xx_l3_hwmod,
+	&omap34xx_l4_core_hwmod,
+	&omap34xx_l4_per_hwmod,
+	&omap34xx_l4_wkup_hwmod,
+	&omap34xx_mpu_hwmod,
+	NULL,
+};
+
+#else
+# define omap34xx_hwmods		0
+#endif
+
+#endif
+
+

arch/arm/mach-omap2/pm.h

@@ -11,12 +11,23 @@
 #ifndef __ARCH_ARM_MACH_OMAP2_PM_H
 #define __ARCH_ARM_MACH_OMAP2_PM_H
 
+#include <mach/powerdomain.h>
+
+extern int omap3_pm_get_suspend_state(struct powerdomain *pwrdm);
+extern int omap3_pm_set_suspend_state(struct powerdomain *pwrdm, int state);
+
 #ifdef CONFIG_PM_DEBUG
 extern void omap2_pm_dump(int mode, int resume, unsigned int us);
 extern int omap2_pm_debug;
+extern void pm_dbg_update_time(struct powerdomain *pwrdm, int prev);
+extern int pm_dbg_regset_save(int reg_set);
+extern int pm_dbg_regset_init(int reg_set);
 #else
 #define omap2_pm_dump(mode, resume, us)		do {} while (0);
 #define omap2_pm_debug				0
+#define pm_dbg_update_time(pwrdm, prev) do {} while (0);
+#define pm_dbg_regset_save(reg_set) do {} while (0);
+#define pm_dbg_regset_init(reg_set) do {} while (0);
 #endif /* CONFIG_PM_DEBUG */
 
 extern void omap24xx_idle_loop_suspend(void);

arch/arm/mach-omap2/pm24xx.c

@@ -333,7 +333,7 @@ static struct platform_suspend_ops omap_pm_ops = {
 	.valid		= suspend_valid_only_mem,
 };
 
-static int _pm_clkdm_enable_hwsup(struct clockdomain *clkdm)
+static int _pm_clkdm_enable_hwsup(struct clockdomain *clkdm, void *unused)
 {
 	omap2_clkdm_allow_idle(clkdm);
 	return 0;
@@ -385,7 +385,7 @@ static void __init prcm_setup_regs(void)
 	omap2_clkdm_sleep(gfx_clkdm);
 
 	/* Enable clockdomain hardware-supervised control for all clkdms */
-	clkdm_for_each(_pm_clkdm_enable_hwsup);
+	clkdm_for_each(_pm_clkdm_enable_hwsup, NULL);
 
 	/* Enable clock autoidle for all domains */
 	cm_write_mod_reg(OMAP24XX_AUTO_CAM |

arch/arm/mach-omap2/prm.h

@@ -17,11 +17,11 @@
 #include "prcm-common.h"
 
 #define OMAP2420_PRM_REGADDR(module, reg)				\
-			IO_ADDRESS(OMAP2420_PRM_BASE + (module) + (reg))
+			OMAP2_IO_ADDRESS(OMAP2420_PRM_BASE + (module) + (reg))
 #define OMAP2430_PRM_REGADDR(module, reg)				\
-			IO_ADDRESS(OMAP2430_PRM_BASE + (module) + (reg))
+			OMAP2_IO_ADDRESS(OMAP2430_PRM_BASE + (module) + (reg))
 #define OMAP34XX_PRM_REGADDR(module, reg)				\
-			IO_ADDRESS(OMAP3430_PRM_BASE + (module) + (reg))
+			OMAP2_IO_ADDRESS(OMAP3430_PRM_BASE + (module) + (reg))
 
 /*
  * Architecture-specific global PRM registers

arch/arm/mach-omap2/sdrc.h

@@ -48,9 +48,9 @@ static inline u32 sms_read_reg(u16 reg)
 	return __raw_readl(OMAP_SMS_REGADDR(reg));
 }
 #else
-#define OMAP242X_SDRC_REGADDR(reg)	IO_ADDRESS(OMAP2420_SDRC_BASE + (reg))
-#define OMAP243X_SDRC_REGADDR(reg)	IO_ADDRESS(OMAP243X_SDRC_BASE + (reg))
-#define OMAP34XX_SDRC_REGADDR(reg)	IO_ADDRESS(OMAP343X_SDRC_BASE + (reg))
+#define OMAP242X_SDRC_REGADDR(reg)	OMAP2_IO_ADDRESS(OMAP2420_SDRC_BASE + (reg))
+#define OMAP243X_SDRC_REGADDR(reg)	OMAP2_IO_ADDRESS(OMAP243X_SDRC_BASE + (reg))
+#define OMAP34XX_SDRC_REGADDR(reg)	OMAP2_IO_ADDRESS(OMAP343X_SDRC_BASE + (reg))
 #endif	/* __ASSEMBLER__ */
 
 #endif

arch/arm/mach-omap2/sram242x.S

@@ -128,7 +128,7 @@ omap242x_sdi_prcm_voltctrl:
 prcm_mask_val:
 	.word 0xFFFF3FFC
 omap242x_sdi_timer_32ksynct_cr:
-	.word IO_ADDRESS(OMAP2420_32KSYNCT_BASE + 0x010)
+	.word OMAP2_IO_ADDRESS(OMAP2420_32KSYNCT_BASE + 0x010)
 ENTRY(omap242x_sram_ddr_init_sz)
 	.word	. - omap242x_sram_ddr_init
 
@@ -224,7 +224,7 @@ omap242x_srs_prcm_voltctrl:
 ddr_prcm_mask_val:
 	.word 0xFFFF3FFC
 omap242x_srs_timer_32ksynct:
-	.word IO_ADDRESS(OMAP2420_32KSYNCT_BASE + 0x010)
+	.word OMAP2_IO_ADDRESS(OMAP2420_32KSYNCT_BASE + 0x010)
 
 ENTRY(omap242x_sram_reprogram_sdrc_sz)
 	.word	. - omap242x_sram_reprogram_sdrc

arch/arm/mach-omap2/sram243x.S

@@ -128,7 +128,7 @@ omap243x_sdi_prcm_voltctrl:
 prcm_mask_val:
 	.word 0xFFFF3FFC
 omap243x_sdi_timer_32ksynct_cr:
-	.word IO_ADDRESS(OMAP2430_32KSYNCT_BASE + 0x010)
+	.word OMAP2_IO_ADDRESS(OMAP2430_32KSYNCT_BASE + 0x010)
 ENTRY(omap243x_sram_ddr_init_sz)
 	.word	. - omap243x_sram_ddr_init
 
@@ -224,7 +224,7 @@ omap243x_srs_prcm_voltctrl:
 ddr_prcm_mask_val:
 	.word 0xFFFF3FFC
 omap243x_srs_timer_32ksynct:
-	.word IO_ADDRESS(OMAP2430_32KSYNCT_BASE + 0x010)
+	.word OMAP2_IO_ADDRESS(OMAP2430_32KSYNCT_BASE + 0x010)
 
 ENTRY(omap243x_sram_reprogram_sdrc_sz)
 	.word	. - omap243x_sram_reprogram_sdrc

arch/arm/mach-omap2/timer-gp.c

@@ -231,7 +231,7 @@ static void __init omap2_gp_clocksource_init(void)
 static void __init omap2_gp_timer_init(void)
 {
 #ifdef CONFIG_LOCAL_TIMERS
-	twd_base = IO_ADDRESS(OMAP44XX_LOCAL_TWD_BASE);
+	twd_base = OMAP2_IO_ADDRESS(OMAP44XX_LOCAL_TWD_BASE);
 #endif
 	omap_dm_timer_init();
 

arch/arm/plat-omap/clock.c

@@ -488,7 +488,7 @@ static int __init clk_debugfs_init(void)
 	}
 	return 0;
 err_out:
-	debugfs_remove(clk_debugfs_root); /* REVISIT: Cleanup correctly */
+	debugfs_remove_recursive(clk_debugfs_root);
 	return err;
 }
 late_initcall(clk_debugfs_init);