net: mdio: mscc-miim: add lan966x internal phy reset support

The LAN966x has two internal PHYs which are in reset by default. The
driver already supported the internal PHYs of the SparX-5. Now add
support for the LAN966x, too. Add a new compatible to distinguish them.

The LAN966x has additional control bits in this register, thus convert
the regmap_write() to regmap_update_bits() to leave the remaining bits
untouched. This doesn't change anything for the SparX-5 SoC, because
there, the register consists only of reset bits.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

drivers/net/mdio/mdio-mscc-miim.c

@@ -15,6 +15,7 @@
 #include <linux/of_mdio.h>
 #include <linux/phy.h>
 #include <linux/platform_device.h>
+#include <linux/property.h>
 #include <linux/regmap.h>
 
 #define MSCC_MIIM_REG_STATUS		0x0
@@ -36,11 +37,19 @@
 #define		PHY_CFG_PHY_RESET	(BIT(5) | BIT(6) | BIT(7) | BIT(8))
 #define MSCC_PHY_REG_PHY_STATUS	0x4
 
+#define LAN966X_CUPHY_COMMON_CFG	0x0
+#define		CUPHY_COMMON_CFG_RESET_N	BIT(0)
+
+struct mscc_miim_info {
+	unsigned int phy_reset_offset;
+	unsigned int phy_reset_bits;
+};
+
 struct mscc_miim_dev {
 	struct regmap *regs;
 	int mii_status_offset;
 	struct regmap *phy_regs;
-	int phy_reset_offset;
+	const struct mscc_miim_info *info;
 };
 
 /* When high resolution timers aren't built-in: we can't use usleep_range() as
@@ -157,26 +166,28 @@ static int mscc_miim_write(struct mii_bus *bus, int mii_id,
 static int mscc_miim_reset(struct mii_bus *bus)
 {
 	struct mscc_miim_dev *miim = bus->priv;
-	int offset = miim->phy_reset_offset;
-	int reset_bits = PHY_CFG_PHY_ENA | PHY_CFG_PHY_COMMON_RESET |
-			 PHY_CFG_PHY_RESET;
+	unsigned int offset, bits;
 	int ret;
 
-	if (miim->phy_regs) {
-		ret = regmap_write(miim->phy_regs, offset, 0);
+	if (!miim->phy_regs)
+		return 0;
+
+	offset = miim->info->phy_reset_offset;
+	bits = miim->info->phy_reset_bits;
+
+	ret = regmap_update_bits(miim->phy_regs, offset, bits, 0);
 	if (ret < 0) {
 		WARN_ONCE(1, "mscc reset set error %d\n", ret);
 		return ret;
 	}
 
-		ret = regmap_write(miim->phy_regs, offset, reset_bits);
+	ret = regmap_update_bits(miim->phy_regs, offset, bits, bits);
 	if (ret < 0) {
 		WARN_ONCE(1, "mscc reset clear error %d\n", ret);
 		return ret;
 	}
 
 	mdelay(500);
-	}
 
 	return 0;
 }
@@ -272,7 +283,10 @@ static int mscc_miim_probe(struct platform_device *pdev)
 
 	miim = bus->priv;
 	miim->phy_regs = phy_regmap;
-	miim->phy_reset_offset = MSCC_PHY_REG_PHY_CFG;
+
+	miim->info = device_get_match_data(&pdev->dev);
+	if (!miim->info)
+		return -EINVAL;
 
 	ret = of_mdiobus_register(bus, pdev->dev.of_node);
 	if (ret < 0) {
@@ -294,8 +308,25 @@ static int mscc_miim_remove(struct platform_device *pdev)
 	return 0;
 }
 
+static const struct mscc_miim_info mscc_ocelot_miim_info = {
+	.phy_reset_offset = MSCC_PHY_REG_PHY_CFG,
+	.phy_reset_bits = PHY_CFG_PHY_ENA | PHY_CFG_PHY_COMMON_RESET |
+			  PHY_CFG_PHY_RESET,
+};
+
+static const struct mscc_miim_info microchip_lan966x_miim_info = {
+	.phy_reset_offset = LAN966X_CUPHY_COMMON_CFG,
+	.phy_reset_bits = CUPHY_COMMON_CFG_RESET_N,
+};
+
 static const struct of_device_id mscc_miim_match[] = {
-	{ .compatible = "mscc,ocelot-miim" },
+	{
+		.compatible = "mscc,ocelot-miim",
+		.data = &mscc_ocelot_miim_info
+	}, {
+		.compatible = "microchip,lan966x-miim",
+		.data = &microchip_lan966x_miim_info
+	},
 	{ }
 };
 MODULE_DEVICE_TABLE(of, mscc_miim_match);