Commit 775637df authored by Andrew Victor's avatar Andrew Victor Committed by Jeff Garzik

[PATCH] AT91RM9200 Ethernet #1: Link poll

For Ethernet PHYs that don't have an IRQ pin or boards that don't
connect the IRQ pin to the processor, we enable a timer to poll the
PHY's link state.

Patch originally supplied by Eric Benard and Roman Kolesnikov.
Signed-off-by: default avatarAndrew Victor <andrew@sanpeople.com>
Signed-off-by: default avatarJeff Garzik <jeff@garzik.org>
parent d955d90b
......@@ -45,6 +45,9 @@
static struct net_device *at91_dev;
static struct clk *ether_clk;
static struct timer_list check_timer;
#define LINK_POLL_INTERVAL (HZ)
/* ..................................................................... */
/*
......@@ -143,7 +146,7 @@ static void read_phy(unsigned char phy_addr, unsigned char address, unsigned int
* MAC accordingly.
* If no link or auto-negotiation is busy, then no changes are made.
*/
static void update_linkspeed(struct net_device *dev)
static void update_linkspeed(struct net_device *dev, int silent)
{
struct at91_private *lp = (struct at91_private *) dev->priv;
unsigned int bmsr, bmcr, lpa, mac_cfg;
......@@ -151,6 +154,7 @@ static void update_linkspeed(struct net_device *dev)
if (!mii_link_ok(&lp->mii)) { /* no link */
netif_carrier_off(dev);
if (!silent)
printk(KERN_INFO "%s: Link down.\n", dev->name);
return;
}
......@@ -186,6 +190,7 @@ static void update_linkspeed(struct net_device *dev)
}
at91_emac_write(AT91_EMAC_CFG, mac_cfg);
if (!silent)
printk(KERN_INFO "%s: Link now %i-%s\n", dev->name, speed, (duplex == DUPLEX_FULL) ? "FullDuplex" : "HalfDuplex");
netif_carrier_on(dev);
}
......@@ -226,7 +231,7 @@ static irqreturn_t at91ether_phy_interrupt(int irq, void *dev_id, struct pt_regs
goto done;
}
update_linkspeed(dev);
update_linkspeed(dev, 0);
done:
disable_mdi();
......@@ -243,14 +248,17 @@ static void enable_phyirq(struct net_device *dev)
unsigned int dsintr, irq_number;
int status;
if (lp->phy_type == MII_RTL8201_ID) /* RTL8201 does not have an interrupt */
return;
if (lp->phy_type == MII_DP83847_ID) /* DP83847 does not have an interrupt */
return;
if (lp->phy_type == MII_AC101L_ID) /* AC101L interrupt not supported yet */
irq_number = lp->board_data.phy_irq_pin;
if (!irq_number) {
/*
* PHY doesn't have an IRQ pin (RTL8201, DP83847, AC101L),
* or board does not have it connected.
*/
check_timer.expires = jiffies + LINK_POLL_INTERVAL;
add_timer(&check_timer);
return;
}
irq_number = lp->board_data.phy_irq_pin;
status = request_irq(irq_number, at91ether_phy_interrupt, 0, dev->name, dev);
if (status) {
printk(KERN_ERR "at91_ether: PHY IRQ %d request failed - status %d!\n", irq_number, status);
......@@ -292,12 +300,11 @@ static void disable_phyirq(struct net_device *dev)
unsigned int dsintr;
unsigned int irq_number;
if (lp->phy_type == MII_RTL8201_ID) /* RTL8201 does not have an interrupt */
return;
if (lp->phy_type == MII_DP83847_ID) /* DP83847 does not have an interrupt */
return;
if (lp->phy_type == MII_AC101L_ID) /* AC101L interrupt not supported yet */
irq_number = lp->board_data.phy_irq_pin;
if (!irq_number) {
del_timer_sync(&check_timer);
return;
}
spin_lock_irq(&lp->lock);
enable_mdi();
......@@ -326,7 +333,6 @@ static void disable_phyirq(struct net_device *dev)
disable_mdi();
spin_unlock_irq(&lp->lock);
irq_number = lp->board_data.phy_irq_pin;
free_irq(irq_number, dev); /* Free interrupt handler */
}
......@@ -355,6 +361,18 @@ static void reset_phy(struct net_device *dev)
}
#endif
static void at91ether_check_link(unsigned long dev_id)
{
struct net_device *dev = (struct net_device *) dev_id;
enable_mdi();
update_linkspeed(dev, 1);
disable_mdi();
check_timer.expires = jiffies + LINK_POLL_INTERVAL;
add_timer(&check_timer);
}
/* ......................... ADDRESS MANAGEMENT ........................ */
/*
......@@ -708,7 +726,7 @@ static int at91ether_open(struct net_device *dev)
/* Determine current link speed */
spin_lock_irq(&lp->lock);
enable_mdi();
update_linkspeed(dev);
update_linkspeed(dev, 0);
disable_mdi();
spin_unlock_irq(&lp->lock);
......@@ -992,11 +1010,18 @@ static int __init at91ether_setup(unsigned long phy_type, unsigned short phy_add
/* Determine current link speed */
spin_lock_irq(&lp->lock);
enable_mdi();
update_linkspeed(dev);
update_linkspeed(dev, 0);
disable_mdi();
spin_unlock_irq(&lp->lock);
netif_carrier_off(dev); /* will be enabled in open() */
/* If board has no PHY IRQ, use a timer to poll the PHY */
if (!lp->board_data.phy_irq_pin) {
init_timer(&check_timer);
check_timer.data = (unsigned long)dev;
check_timer.function = at91ether_check_link;
}
/* Display ethernet banner */
printk(KERN_INFO "%s: AT91 ethernet at 0x%08x int=%d %s%s (%02x:%02x:%02x:%02x:%02x:%02x)\n",
dev->name, (uint) dev->base_addr, dev->irq,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment