Commit 7a0b3b08 authored by Johannes Berg's avatar Johannes Berg Committed by Wey-Yi Guy

iwlwifi: remove unused AMPDU factor/density configuration

These are unused, so can be removed safely. They also
don't make a lot of sense in Bluetooth configuration.
Signed-off-by: default avatarJohannes Berg <johannes.berg@intel.com>
Signed-off-by: default avatarWey-Yi Guy <wey-yi.w.guy@intel.com>
parent 69a679b0
...@@ -76,11 +76,7 @@ static void iwl_init_ht_hw_capab(const struct iwl_priv *priv, ...@@ -76,11 +76,7 @@ static void iwl_init_ht_hw_capab(const struct iwl_priv *priv,
ht_info->cap |= IEEE80211_HT_CAP_MAX_AMSDU; ht_info->cap |= IEEE80211_HT_CAP_MAX_AMSDU;
ht_info->ampdu_factor = CFG_HT_RX_AMPDU_FACTOR_DEF; ht_info->ampdu_factor = CFG_HT_RX_AMPDU_FACTOR_DEF;
if (cfg(priv)->bt_params && cfg(priv)->bt_params->ampdu_factor)
ht_info->ampdu_factor = cfg(priv)->bt_params->ampdu_factor;
ht_info->ampdu_density = CFG_HT_MPDU_DENSITY_DEF; ht_info->ampdu_density = CFG_HT_MPDU_DENSITY_DEF;
if (cfg(priv)->bt_params && cfg(priv)->bt_params->ampdu_density)
ht_info->ampdu_density = cfg(priv)->bt_params->ampdu_density;
ht_info->mcs.rx_mask[0] = 0xFF; ht_info->mcs.rx_mask[0] = 0xFF;
if (rx_chains_num >= 2) if (rx_chains_num >= 2)
......
...@@ -142,8 +142,6 @@ struct iwl_base_params { ...@@ -142,8 +142,6 @@ struct iwl_base_params {
* @bt_init_traffic_load: specify initial bt traffic load * @bt_init_traffic_load: specify initial bt traffic load
* @bt_prio_boost: default bt priority boost value * @bt_prio_boost: default bt priority boost value
* @agg_time_limit: maximum number of uSec in aggregation * @agg_time_limit: maximum number of uSec in aggregation
* @ampdu_factor: Maximum A-MPDU length factor
* @ampdu_density: Minimum A-MPDU spacing
* @bt_sco_disable: uCode should not response to BT in SCO/ESCO mode * @bt_sco_disable: uCode should not response to BT in SCO/ESCO mode
*/ */
struct iwl_bt_params { struct iwl_bt_params {
...@@ -151,8 +149,6 @@ struct iwl_bt_params { ...@@ -151,8 +149,6 @@ struct iwl_bt_params {
u8 bt_init_traffic_load; u8 bt_init_traffic_load;
u8 bt_prio_boost; u8 bt_prio_boost;
u16 agg_time_limit; u16 agg_time_limit;
u8 ampdu_factor;
u8 ampdu_density;
bool bt_sco_disable; bool bt_sco_disable;
bool bt_session_2; bool bt_session_2;
}; };
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment