Commit 7b6f9462 authored by Paul M Stillwell Jr's avatar Paul M Stillwell Jr Committed by Tony Nguyen

ice: change devlink code to read NVM in blocks

When creating a snapshot of the NVM the driver needs to read the entire
contents from the NVM and store it. The NVM reads are protected by a lock
that is shared between the driver and the firmware.

If the driver takes too long to read the entire NVM (which can happen on
some systems) then the firmware could reclaim the lock and cause subsequent
reads from the driver to fail.

We could fix this by increasing the timeout that we pass to the firmware,
but we could end up in the same situation again if the system is slow.
Instead have the driver break the reading of the NVM into blocks that are
small enough that we have confidence that the read will complete within the
timeout time, but large enough not to cause significant AQ overhead.

Fixes: dce730f1 ("ice: add a devlink region for dumping NVM contents")
Signed-off-by: default avatarPaul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: default avatarTony Nguyen <anthony.l.nguyen@intel.com>
parent f52d1668
......@@ -814,6 +814,8 @@ void ice_devlink_destroy_vf_port(struct ice_vf *vf)
devlink_port_unregister(devlink_port);
}
#define ICE_DEVLINK_READ_BLK_SIZE (1024 * 1024)
/**
* ice_devlink_nvm_snapshot - Capture a snapshot of the NVM flash contents
* @devlink: the devlink instance
......@@ -840,8 +842,9 @@ static int ice_devlink_nvm_snapshot(struct devlink *devlink,
struct ice_pf *pf = devlink_priv(devlink);
struct device *dev = ice_pf_to_dev(pf);
struct ice_hw *hw = &pf->hw;
void *nvm_data;
u32 nvm_size;
u8 *nvm_data, *tmp, i;
u32 nvm_size, left;
s8 num_blks;
int status;
nvm_size = hw->flash.flash_size;
......@@ -849,27 +852,45 @@ static int ice_devlink_nvm_snapshot(struct devlink *devlink,
if (!nvm_data)
return -ENOMEM;
num_blks = DIV_ROUND_UP(nvm_size, ICE_DEVLINK_READ_BLK_SIZE);
tmp = nvm_data;
left = nvm_size;
/* Some systems take longer to read the NVM than others which causes the
* FW to reclaim the NVM lock before the entire NVM has been read. Fix
* this by breaking the reads of the NVM into smaller chunks that will
* probably not take as long. This has some overhead since we are
* increasing the number of AQ commands, but it should always work
*/
for (i = 0; i < num_blks; i++) {
u32 read_sz = min_t(u32, ICE_DEVLINK_READ_BLK_SIZE, left);
status = ice_acquire_nvm(hw, ICE_RES_READ);
if (status) {
dev_dbg(dev, "ice_acquire_nvm failed, err %d aq_err %d\n",
status, hw->adminq.sq_last_status);
NL_SET_ERR_MSG_MOD(extack, "Failed to acquire NVM semaphore");
vfree(nvm_data);
return status;
return -EIO;
}
status = ice_read_flat_nvm(hw, 0, &nvm_size, nvm_data, false);
status = ice_read_flat_nvm(hw, i * ICE_DEVLINK_READ_BLK_SIZE,
&read_sz, tmp, false);
if (status) {
dev_dbg(dev, "ice_read_flat_nvm failed after reading %u bytes, err %d aq_err %d\n",
nvm_size, status, hw->adminq.sq_last_status);
read_sz, status, hw->adminq.sq_last_status);
NL_SET_ERR_MSG_MOD(extack, "Failed to read NVM contents");
ice_release_nvm(hw);
vfree(nvm_data);
return status;
return -EIO;
}
ice_release_nvm(hw);
tmp += read_sz;
left -= read_sz;
}
*data = nvm_data;
return 0;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment