Commit 7cf241a1 authored by Leo Kim's avatar Leo Kim Committed by Greg Kroah-Hartman

staging: wilc1000: wilc_wlan.h: alignment defines

This patch fixes alignment of defines.
Signed-off-by: default avatarLeo Kim <leo.kim@atmel.com>
Signed-off-by: default avatarGlen Lee <glen.lee@atmel.com>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent 92e7d188
......@@ -3,7 +3,7 @@
#define ISWILC1000(id) (((id & 0xfffff000) == 0x100000) ? 1 : 0)
#define ISWILC1000(id) ((id & 0xfffff000) == 0x100000 ? 1 : 0)
/********************************************
......@@ -18,8 +18,11 @@
#define ETHERNET_HDR_LEN 14
#define WORD_ALIGNMENT_PAD 0
#define ETH_ETHERNET_HDR_OFFSET (MAX_MAC_HDR_LEN + SUB_MSDU_HEADER_LENGTH + \
SNAP_HDR_LEN - ETHERNET_HDR_LEN + WORD_ALIGNMENT_PAD)
#define ETH_ETHERNET_HDR_OFFSET (MAX_MAC_HDR_LEN + \
SUB_MSDU_HEADER_LENGTH + \
SNAP_HDR_LEN - \
ETHERNET_HDR_LEN + \
WORD_ALIGNMENT_PAD)
#define HOST_HDR_OFFSET 4
#define ETHERNET_HDR_LEN 14
......@@ -39,10 +42,10 @@
*
********************************************/
#define BYTE_SWAP(val) ((((val) & 0x000000FF) << 24) + \
(((val) & 0x0000FF00) << 8) + \
(((val) & 0x00FF0000) >> 8) + \
(((val) & 0xFF000000) >> 24))
#define BYTE_SWAP(val) (((val & 0x000000FF) << 24) + \
((val & 0x0000FF00) << 8) + \
((val & 0x00FF0000) >> 8) + \
((val & 0xFF000000) >> 24))
/********************************************
*
......@@ -50,8 +53,8 @@
*
********************************************/
#define WILC_PERIPH_REG_BASE 0x1000
#define WILC_CHANGING_VIR_IF (0x108c)
#define WILC_CHIPID (WILC_PERIPH_REG_BASE)
#define WILC_CHANGING_VIR_IF 0x108c
#define WILC_CHIPID WILC_PERIPH_REG_BASE
#define WILC_GLB_RESET_0 (WILC_PERIPH_REG_BASE + 0x400)
#define WILC_PIN_MUX_0 (WILC_PERIPH_REG_BASE + 0x408)
#define WILC_HOST_TX_CTRL (WILC_PERIPH_REG_BASE + 0x6c)
......@@ -63,7 +66,7 @@
#define WILC_HOST_TX_CTRL_1 (WILC_PERIPH_REG_BASE + 0x88)
#define WILC_MISC (WILC_PERIPH_REG_BASE + 0x428)
#define WILC_INTR_REG_BASE (WILC_PERIPH_REG_BASE + 0xa00)
#define WILC_INTR_ENABLE (WILC_INTR_REG_BASE)
#define WILC_INTR_ENABLE WILC_INTR_REG_BASE
#define WILC_INTR2_ENABLE (WILC_INTR_REG_BASE + 4)
#define WILC_INTR_POLARITY (WILC_INTR_REG_BASE + 0x10)
......@@ -72,11 +75,11 @@
#define WILC_INTR_STATUS (WILC_INTR_REG_BASE + 0x40)
#define WILC_VMM_TBL_SIZE 64
#define WILC_VMM_TX_TBL_BASE (0x150400)
#define WILC_VMM_RX_TBL_BASE (0x150500)
#define WILC_VMM_TX_TBL_BASE 0x150400
#define WILC_VMM_RX_TBL_BASE 0x150500
#define WILC_VMM_BASE 0x150000
#define WILC_VMM_CORE_CTL (WILC_VMM_BASE)
#define WILC_VMM_CORE_CTL WILC_VMM_BASE
#define WILC_VMM_TBL_CTL (WILC_VMM_BASE + 0x4)
#define WILC_VMM_TBL_ENTRY (WILC_VMM_BASE + 0x8)
#define WILC_VMM_TBL0_SIZE (WILC_VMM_BASE + 0xc)
......@@ -86,7 +89,7 @@
#define WILC_VMM_TBL_STATUS (WILC_VMM_BASE + 0x44)
#define WILC_SPI_REG_BASE 0xe800
#define WILC_SPI_CTL (WILC_SPI_REG_BASE)
#define WILC_SPI_CTL WILC_SPI_REG_BASE
#define WILC_SPI_MASTER_DMA_ADDR (WILC_SPI_REG_BASE + 0x4)
#define WILC_SPI_MASTER_DMA_COUNT (WILC_SPI_REG_BASE + 0x8)
#define WILC_SPI_SLAVE_DMA_ADDR (WILC_SPI_REG_BASE + 0xc)
......@@ -95,25 +98,26 @@
#define WILC_SPI_PROTOCOL_CONFIG (WILC_SPI_REG_BASE + 0x24)
#define WILC_SPI_INTR_CTL (WILC_SPI_REG_BASE + 0x2c)
#define WILC_SPI_PROTOCOL_OFFSET (WILC_SPI_PROTOCOL_CONFIG - WILC_SPI_REG_BASE)
#define WILC_SPI_PROTOCOL_OFFSET (WILC_SPI_PROTOCOL_CONFIG - \
WILC_SPI_REG_BASE)
#define WILC_AHB_DATA_MEM_BASE 0x30000
#define WILC_AHB_SHARE_MEM_BASE 0xd0000
#define WILC_VMM_TBL_RX_SHADOW_BASE WILC_AHB_SHARE_MEM_BASE
#define WILC_VMM_TBL_RX_SHADOW_SIZE (256)
#define WILC_VMM_TBL_RX_SHADOW_SIZE 256
#define WILC_GP_REG_0 0x149c
#define WILC_GP_REG_1 0x14a0
#define rHAVE_SDIO_IRQ_GPIO_BIT (0)
#define rHAVE_USE_PMU_BIT (1)
#define rHAVE_SLEEP_CLK_SRC_RTC_BIT (2)
#define rHAVE_SLEEP_CLK_SRC_XO_BIT (3)
#define rHAVE_EXT_PA_INV_TX_RX_BIT (4)
#define rHAVE_LEGACY_RF_SETTINGS_BIT (5)
#define rHAVE_XTAL_24_BIT (6)
#define rHAVE_DISABLE_WILC_UART_BIT (7)
#define rHAVE_SDIO_IRQ_GPIO_BIT 0
#define rHAVE_USE_PMU_BIT 1
#define rHAVE_SLEEP_CLK_SRC_RTC_BIT 2
#define rHAVE_SLEEP_CLK_SRC_XO_BIT 3
#define rHAVE_EXT_PA_INV_TX_RX_BIT 4
#define rHAVE_LEGACY_RF_SETTINGS_BIT 5
#define rHAVE_XTAL_24_BIT 6
#define rHAVE_DISABLE_WILC_UART_BIT 7
#define WILC_HAVE_SDIO_IRQ_GPIO (1 << rHAVE_SDIO_IRQ_GPIO_BIT)
......@@ -167,13 +171,13 @@
/*******************************************/
#define IRG_FLAGS_OFFSET 16
#define IRQ_DMA_WD_CNT_MASK ((1ul << IRG_FLAGS_OFFSET) - 1)
#define INT_0 (1 << (IRG_FLAGS_OFFSET))
#define INT_0 (1 << IRG_FLAGS_OFFSET)
#define INT_1 (1 << (IRG_FLAGS_OFFSET + 1))
#define INT_2 (1 << (IRG_FLAGS_OFFSET + 2))
#define INT_3 (1 << (IRG_FLAGS_OFFSET + 3))
#define INT_4 (1 << (IRG_FLAGS_OFFSET + 4))
#define INT_5 (1 << (IRG_FLAGS_OFFSET + 5))
#define MAX_NUM_INT (6)
#define MAX_NUM_INT 6
/*******************************************/
/* E0 and later Interrupt flags. */
......@@ -202,7 +206,7 @@
#define PLL_INT_EXT INT_1
#define SLEEP_INT_EXT INT_2
#define ALL_INT_EXT (DATA_INT_EXT | PLL_INT_EXT | SLEEP_INT_EXT)
#define NUM_INT_EXT (3)
#define NUM_INT_EXT 3
#define DATA_INT_CLR CLR_INT0
#define PLL_INT_CLR CLR_INT1
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment