Skip to content

L
linux
Commit 806af7cc authored by Greg Kroah-Hartman's avatar Greg Kroah-Hartman
Browse files
Options

USB 

spilt up the Config.help file into smaller pieces
parent 781045a2
Show whitespace changes
Inline Side-by-side
Showing with 503 additions and 509 deletions
drivers/usb/Config.help
View file @ 806af7cc
...@@ -37,387 +37,6 @@ CONFIG_USB_LONG_TIMEOUT ...@@ -37,387 +37,6 @@ CONFIG_USB_LONG_TIMEOUT
If you have an MGE Ellipse UPS, or you see timeouts in HID If you have an MGE Ellipse UPS, or you see timeouts in HID
transactions, say Y; otherwise say N. transactions, say Y; otherwise say N.
CONFIG_USB_HID
Say Y here if you want full HID support to connect keyboards,
mice, joysticks, graphic tablets, or any other HID based devices
to your computer via USB. You also need to select HID Input layer
support (below) if you want to use keyboards, mice, joysticks and
the like.
You can't use this driver and the HIDBP (Boot Protocol) keyboard
and mouse drivers at the same time. More information is available:
<file:Documentation/input/input.txt>.
If unsure, say Y.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called hid.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_HIDINPUT
Say Y here if you want to use a USB keyboard, mouse or joystick,
or any other HID input device. You also need Input layer support,
(CONFIG_INPUT) which you select under "Input core support".
If unsure, say Y.
CONFIG_USB_HIDDEV
Say Y here if you want to support HID devices (from the USB
specification standpoint) that aren't strictly user interface
devices, like monitor controls and Uninterruptable Power Supplies.
This module supports these devices separately using a separate
event interface on /dev/usb/hiddevX (char 180:96 to 180:111).
This driver requires CONFIG_USB_HID.
If unsure, say Y.
CONFIG_USB_KBD
Say Y here only if you are absolutely sure that you don't want
to use the generic HID driver for your USB keyboard and prefer
to use the keyboard in its limited Boot Protocol mode instead.
This is almost certainly not what you want.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called usbkbd.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
If even remotely unsure, say N.
CONFIG_USB_MOUSE
Say Y here only if you are absolutely sure that you don't want
to use the generic HID driver for your USB keyboard and prefer
to use the keyboard in its limited Boot Protocol mode instead.
This is almost certainly not what you want.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called usbmouse.o. If you want to compile it as
a module, say M here and read <file:Documentation/modules.txt>.
If even remotely unsure, say N.
CONFIG_USB_WACOM
Say Y here if you want to use the USB version of the Wacom Intuos
or Graphire tablet. Make sure to say Y to "Mouse support"
(CONFIG_INPUT_MOUSEDEV) and/or "Event interface support"
(CONFIG_INPUT_EVDEV) as well.
This driver is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called wacom.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_SCANNER
Say Y here if you want to connect a USB scanner to your computer's
USB port. Please read <file:Documentation/usb/scanner.txt> and
<file:Documentation/usb/scanner-hp-sane.txt> for more information.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called scanner.o. If you want to compile it as
a module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_AUDIO
Say Y here if you want to connect USB audio equipment such as
speakers to your computer's USB port.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called audio.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_EMI26
This driver loads firmware to Emagic EMI 2|6 low latency USB
Audio interface.
After firmware load the device is handled with standard linux
USB Audio driver.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called audio.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_ACM
This driver supports USB modems and ISDN adapters which support the
Communication Device Class Abstract Control Model interface.
Please read <file:Documentation/usb/acm.txt> for details.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called acm.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_PRINTER
Say Y here if you want to connect a USB printer to your computer's
USB port.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called printer.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_IBMCAM
Say Y here if you want to connect a IBM "C-It" camera, also known as
"Xirlink PC Camera" to your computer's USB port. For more
information, read <file:Documentation/usb/ibmcam.txt>.
This driver uses the Video For Linux API. You must enable
(Y or M in config) Video For Linux (under Character Devices)
to use this driver. Information on this API and pointers to
"v4l" programs may be found on the WWW at
<http://roadrunner.swansea.uk.linux.org/v4l.shtml>.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called ibmcam.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>. This
camera has several configuration options which can be specified when
you load the module. Read <file:Documentation/usb/ibmcam.txt> to
learn more.
CONFIG_USB_OV511
Say Y here if you want to connect this type of camera to your
computer's USB port. See <file:Documentation/usb/ov511.txt> for more
information and for a list of supported cameras.
This driver uses the Video For Linux API. You must say Y or M to
"Video For Linux" (under Character Devices) to use this driver.
Information on this API and pointers to "v4l" programs may be found
on the WWW at <http://roadrunner.swansea.uk.linux.org/v4l.shtml>.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called ov511.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_CDCETHER
This driver supports devices conforming to the Communication Device
Class Ethernet Control Model. This is used in some cable modems.
For more details on the specification, get the Communication Device
Class specification from <http://www.usb.org/>.
This driver should work with the following devices:
* Ericsson PipeRider (all variants)
* Motorola (DM100 and SB4100)
* Broadcom Cable Modem (reference design)
* Toshiba PCX1100U and possibly other cable modems
The device creates a network device (ethX, where X depends on what
other networking devices you have in use), as for a normal PCI
or ISA based ethernet network card.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called CDCEther.o. If you want to compile it as
a module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_PWC
Say Y or M here if you want to use one of these Philips USB webcams:
PCA645, PCA646, PCVC675, PCVC680, PCVC690, PCVC730, PCVC740, or
the Askey VC010. The PCA635, PCVC665 and PCVC720 are not supported
by this driver and never will be.
This driver has an optional plugin, which is distributed as a binary
module only. It contains code that allow you to use higher
resolutions and framerates but may not be distributed as source.
But even without this plugin you can these cams for most
applications.
See <file:Documentation/usb/philips.txt> for more information and
installation instructions.
The built-in microphone is enabled by selecting USB Audio support.
This driver uses the Video For Linux API. You must say Y or M to
"Video For Linux" (under Character Devices) to use this driver.
Information on this API and pointers to "v4l" programs may be found
on the WWW at <http://roadrunner.swansea.uk.linux.org/v4l.shtml>.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called pwc.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_SE401
Say Y here if you want to connect this type of camera to your
computer's USB port. See <file:Documentation/usb/se401.txt> for more
information and for a list of supported cameras.
This driver uses the Video For Linux API. You must say Y or M to
"Video For Linux" (under Multimedia Devices) to use this driver.
Information on this API and pointers to "v4l" programs may be found
on the WWW at <http://roadrunner.swansea.uk.linux.org/v4l.shtml>.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called se401.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_STV680
Say Y here if you want to connect this type of camera to your
computer's USB port. This includes the Pencam line of cameras.
See <file:Documentation/usb/stv680.txt> for more information and for
a list of supported cameras.
This driver uses the Video For Linux API. You must say Y or M to
"Video For Linux" (under Multimedia Devices) to use this driver.
Information on this API and pointers to "v4l" programs may be found
on the WWW at <http://roadrunner.swansea.uk.linux.org/v4l.shtml>.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called stv680.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_VICAM
Say Y here if you have 3com homeconnect camera (vicam).
This driver uses the Video For Linux API. You must say Y or M to
"Video For Linux" (under Multimedia Devices) to use this driver.
Information on this API and pointers to "v4l" programs may be found
on the WWW at <http://roadrunner.swansea.uk.linux.org/v4l.shtml>.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called vicam.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_PEGASUS
Say Y here if you know you have Pegasus or Pegasus-II based adapter.
If in doubt then look at linux/drivers/usb/pegasus.h for the complete
list of supported devices.
If your particular adapter is not in the list and you are _sure_ it
is Pegasus or Pegasus II based then send me (petkan@users.sourceforge.net)
vendor and device IDs.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called pegasus.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_RTL8150
Say Y here if you have RTL8150 based usb-ethernet adapter.
Send me (petkan@users.sourceforge.net) any comments you may have.
You can also check for updates at http://pegasus2.sourceforge.net/
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called rtl8150.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_KAWETH
Say Y here if you want to use one of the following 10Mbps only
USB Ethernet adapters based on the KLSI KL5KUSB101B chipset:
3Com 3C19250
ADS USB-10BT
ATEN USB Ethernet
ASANTE USB To Ethernet Adapter
AOX Endpoints USB Ethernet
Correga K.K.
D-Link DSB-650C and DU-E10
Entrega / Portgear E45
I-O DATA USB-ET/T
Jaton USB Ethernet Device Adapter
Kingston Technology USB Ethernet Adapter
Linksys USB10T
Mobility USB-Ethernet Adapter
NetGear EA-101
Peracom Enet and Enet2
Portsmith Express Ethernet Adapter
Shark Pocket Adapter
SMC 2202USB
Sony Vaio port extender
This driver is likely to work with most 10Mbps only USB Ethernet
adapters, including some "no brand" devices. It does NOT work on
SmartBridges smartNIC or on Belkin F5U111 devices - you should use
the CATC NetMate driver for those. If you are not sure which one
you need, select both, and the correct one should be selected for
you.
This driver makes the adapter appear as a normal Ethernet interface,
typically on eth0, if it is the only ethernet device, or perhaps on
eth1, if you have a PCI or ISA ethernet card installed.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called kaweth.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_CATC
Say Y if you want to use one of the following 10Mbps USB Ethernet
device based on the EL1210A chip. Supported devices are:
Belkin F5U011
Belkin F5U111
CATC NetMate
CATC NetMate II
smartBridges smartNIC
This driver makes the adapter appear as a normal Ethernet interface,
typically on eth0, if it is the only ethernet device, or perhaps on
eth1, if you have a PCI or ISA ethernet card installed.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called catc.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_DC2XX
Say Y here if you want to connect this type of still camera to your
computer's USB port. See <file:Documentation/usb/dc2xx.txt> for
more information; some non-Kodak cameras may also work with this
driver, given application support (such as <http://www.gphoto.org/>).
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called dc2xx.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_MDC800
Say Y here if you want to connect this type of still camera to
your computer's USB port. This driver can be used with gphoto 0.4.3
and higher (look at <http://www.gphoto.org/>).
To use it create a device node with "mknod /dev/mustek c 180 32" and
configure it in your software.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called mdc800.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_USS720
This driver is for USB parallel port adapters that use the Lucent
Technologies USS-720 chip. These cables are plugged into your USB
port and provide USB compatibility to peripherals designed with
parallel port interfaces.
The chip has two modes: automatic mode and manual mode. In automatic
mode, it looks to the computer like a standard USB printer. Only
printers may be connected to the USS-720 in this mode. The generic
USB printer driver ("USB Printer support", above) may be used in
that mode, and you can say N here if you want to use the chip only
in this mode.
Manual mode is not limited to printers, any parallel port
device should work. This driver utilizes manual mode.
Note however that some operations are three orders of magnitude
slower than on a PCI/ISA Parallel Port, so timing critical
applications might not work.
Say Y here if you own an USS-720 USB->Parport cable and intend to
connect anything other than a printer to it.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called uss720.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_DEVICEFS CONFIG_USB_DEVICEFS
If you say Y here (and to "/proc file system support" in the "File If you say Y here (and to "/proc file system support" in the "File
systems section, above), you will get a file /proc/bus/usb/devices systems section, above), you will get a file /proc/bus/usb/devices
...@@ -430,8 +49,8 @@ CONFIG_USB_DEVICEFS ...@@ -430,8 +49,8 @@ CONFIG_USB_DEVICEFS
meaning they are generated on the fly and not stored on the hard meaning they are generated on the fly and not stored on the hard
drive. drive.
You may need to mount the usbdevfs file system to see the files, use You may need to mount the usbfs file system to see the files, use
mount -t usbdevfs none /proc/bus/usb mount -t usbfs none /proc/bus/usb
For the format of the various /proc/bus/usb/ files, please read For the format of the various /proc/bus/usb/ files, please read
<file:Documentation/usb/proc_usb_info.txt>. <file:Documentation/usb/proc_usb_info.txt>.
...@@ -450,129 +69,3 @@ CONFIG_USB_BANDWIDTH ...@@ -450,129 +69,3 @@ CONFIG_USB_BANDWIDTH
If you say N here, these conditions will cause warning messages If you say N here, these conditions will cause warning messages
about USB bandwidth usage to be logged and some devices or about USB bandwidth usage to be logged and some devices or
drivers may not work correctly. drivers may not work correctly.
CONFIG_USB_DABUSB
A Digital Audio Broadcasting (DAB) Receiver for USB and Linux
brought to you by the DAB-Team (<http://dab.in.tum.de/>). This
driver can be taken as an example for URB-based bulk, control, and
isochronous transactions. URB's are explained in
<file:Documentation/usb/URB.txt>.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called dabusb.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_KONICAWC
Say Y here if you want support for webcams based on a Konica
chipset. This is known to work with the Intel YC76 webcam.
This driver uses the Video For Linux API. You must enable
(Y or M in config) Video For Linux (under Character Devices)
to use this driver. Information on this API and pointers to
"v4l" programs may be found on the WWW at
<http://roadrunner.swansea.uk.linux.org/v4l.shtml>.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called konicawc.o. If you want to compile it as
a module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_USBNET
This driver supports network links over USB with USB "Network"
or "data transfer" cables, often used to network laptops to PCs.
Such cables have chips from suppliers such as Belkin/eTEK, GeneSys
(GeneLink), NetChip and Prolific. Intelligent USB devices could also
use this approach to provide Internet access, using standard USB
cabling. You can find these chips also on some motherboards with
USB PC2PC support.
These links will have names like "usb0", "usb1", etc. They act
like two-node Ethernets, so you can use 802.1d Ethernet Bridging
(CONFIG_BRIDGE) to simplify your network routing.
This code is also available as a kernel module (code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called usbnet.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_RIO500
Say Y here if you want to connect a USB Rio500 mp3 player to your
computer's USB port. Please read <file:Documentation/usb/rio.txt>
for more information.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called rio500.o. If you want to compile it as
a module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_AUERSWALD
Say Y here if you want to connect an Auerswald USB ISDN Device
to your computer's USB port.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called auerswald.o. If you want to compile it as
a module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_DSBR
Say Y here if you want to connect this type of radio to your
computer's USB port. Note that the audio is not digital, and
you must connect the line out connector to a sound card or a
set of speakers.
This driver uses the Video For Linux API. You must enable
(Y or M in config) Video For Linux (under Character Devices)
to use this driver. Information on this API and pointers to
"v4l" programs may be found on the WWW at
<http://roadrunner.swansea.uk.linux.org/v4l.shtml>.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called dsbr100.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_MICROTEK
Say Y here if you want support for the Microtek X6USB and
possibly the Phantom 336CX, Phantom C6 and ScanMaker V6U(S)L.
Support for anything but the X6 is experimental.
Please report failures and successes.
The scanner will appear as a scsi generic device to the rest
of the system. Scsi support is required.
This driver can be compiled as a module, called microtek.o.
CONFIG_USB_HPUSBSCSI
Say Y here if you want support for the HP 53xx series of scanners
and the Minolta Scan Dual. This driver is experimental.
The scanner will be accessible as a SCSI device.
This can be compiled as a module, called hpusbscsi.o.
CONFIG_USB_BLUETOOTH
Say Y here if you want to connect a USB Bluetooth device to your
computer's USB port. You will need the Bluetooth stack (available
at <http://developer.axis.com/software/index.shtml>) to fully use
the device.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called bluetooth.o. If you want to compile it as
a module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_TIGL
If you own a Texas Instruments graphing calculator and use a
TI-GRAPH LINK USB cable (aka SilverLink), then you might be
interested in this driver.
If you enable this driver, you will be able to communicate with
your calculator through a set of device nodes under /dev.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called tiglusb.o. If you want to compile it as a
module, say M here and read Documentation/modules.txt.
If you don't know what the SilverLink cable is or what a Texas
Instruments graphing calculator is, then you probably don't need this
driver.
If unsure, say N.
drivers/usb/class/Config.help 0 → 100644
View file @ 806af7cc
CONFIG_USB_ACM
This driver supports USB modems and ISDN adapters which support the
Communication Device Class Abstract Control Model interface.
Please read <file:Documentation/usb/acm.txt> for details.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called acm.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_AUDIO
Say Y here if you want to connect USB audio equipment such as
speakers to your computer's USB port.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called audio.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_BLUETOOTH
Say Y here if you want to connect a USB Bluetooth device to your
computer's USB port. You will need the Bluetooth stack (available
at <http://developer.axis.com/software/index.shtml>) to fully use
the device.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called bluetooth.o. If you want to compile it as
a module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_PRINTER
Say Y here if you want to connect a USB printer to your computer's
USB port.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called printer.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
drivers/usb/image/Config.help 0 → 100644
View file @ 806af7cc
CONFIG_USB_DC2XX
Say Y here if you want to connect this type of still camera to your
computer's USB port. See <file:Documentation/usb/dc2xx.txt> for
more information; some non-Kodak cameras may also work with this
driver, given application support (such as <http://www.gphoto.org/>).
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called dc2xx.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_MDC800
Say Y here if you want to connect this type of still camera to
your computer's USB port. This driver can be used with gphoto 0.4.3
and higher (look at <http://www.gphoto.org/>).
To use it create a device node with "mknod /dev/mustek c 180 32" and
configure it in your software.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called mdc800.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_HPUSBSCSI
Say Y here if you want support for the HP 53xx series of scanners
and the Minolta Scan Dual. This driver is experimental.
The scanner will be accessible as a SCSI device.
This can be compiled as a module, called hpusbscsi.o.
CONFIG_USB_MICROTEK
Say Y here if you want support for the Microtek X6USB and
possibly the Phantom 336CX, Phantom C6 and ScanMaker V6U(S)L.
Support for anything but the X6 is experimental.
Please report failures and successes.
The scanner will appear as a scsi generic device to the rest
of the system. Scsi support is required.
This driver can be compiled as a module, called microtek.o.
CONFIG_USB_SCANNER
Say Y here if you want to connect a USB scanner to your computer's
USB port. Please read <file:Documentation/usb/scanner.txt> and
<file:Documentation/usb/scanner-hp-sane.txt> for more information.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called scanner.o. If you want to compile it as
a module, say M here and read <file:Documentation/modules.txt>.
drivers/usb/input/Config.help 0 → 100644
View file @ 806af7cc
CONFIG_USB_HID
Say Y here if you want full HID support to connect keyboards,
mice, joysticks, graphic tablets, or any other HID based devices
to your computer via USB. You also need to select HID Input layer
support (below) if you want to use keyboards, mice, joysticks and
the like.
You can't use this driver and the HIDBP (Boot Protocol) keyboard
and mouse drivers at the same time. More information is available:
<file:Documentation/input/input.txt>.
If unsure, say Y.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called hid.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_HIDINPUT
Say Y here if you want to use a USB keyboard, mouse or joystick,
or any other HID input device. You also need Input layer support,
(CONFIG_INPUT) which you select under "Input core support".
If unsure, say Y.
CONFIG_USB_HIDDEV
Say Y here if you want to support HID devices (from the USB
specification standpoint) that aren't strictly user interface
devices, like monitor controls and Uninterruptable Power Supplies.
This module supports these devices separately using a separate
event interface on /dev/usb/hiddevX (char 180:96 to 180:111).
This driver requires CONFIG_USB_HID.
If unsure, say Y.
CONFIG_USB_KBD
Say Y here only if you are absolutely sure that you don't want
to use the generic HID driver for your USB keyboard and prefer
to use the keyboard in its limited Boot Protocol mode instead.
This is almost certainly not what you want.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called usbkbd.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
If even remotely unsure, say N.
CONFIG_USB_MOUSE
Say Y here only if you are absolutely sure that you don't want
to use the generic HID driver for your USB keyboard and prefer
to use the keyboard in its limited Boot Protocol mode instead.
This is almost certainly not what you want.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called usbmouse.o. If you want to compile it as
a module, say M here and read <file:Documentation/modules.txt>.
If even remotely unsure, say N.
CONFIG_USB_WACOM
Say Y here if you want to use the USB version of the Wacom Intuos
or Graphire tablet. Make sure to say Y to "Mouse support"
(CONFIG_INPUT_MOUSEDEV) and/or "Event interface support"
(CONFIG_INPUT_EVDEV) as well.
This driver is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called wacom.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
drivers/usb/media/Config.help 0 → 100644
View file @ 806af7cc
CONFIG_USB_DABUSB
A Digital Audio Broadcasting (DAB) Receiver for USB and Linux
brought to you by the DAB-Team (<http://dab.in.tum.de/>). This
driver can be taken as an example for URB-based bulk, control, and
isochronous transactions. URB's are explained in
<file:Documentation/usb/URB.txt>.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called dabusb.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_DSBR
Say Y here if you want to connect this type of radio to your
computer's USB port. Note that the audio is not digital, and
you must connect the line out connector to a sound card or a
set of speakers.
This driver uses the Video For Linux API. You must enable
(Y or M in config) Video For Linux (under Character Devices)
to use this driver. Information on this API and pointers to
"v4l" programs may be found on the WWW at
<http://roadrunner.swansea.uk.linux.org/v4l.shtml>.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called dsbr100.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_IBMCAM
Say Y here if you want to connect a IBM "C-It" camera, also known as
"Xirlink PC Camera" to your computer's USB port. For more
information, read <file:Documentation/usb/ibmcam.txt>.
This driver uses the Video For Linux API. You must enable
(Y or M in config) Video For Linux (under Character Devices)
to use this driver. Information on this API and pointers to
"v4l" programs may be found on the WWW at
<http://roadrunner.swansea.uk.linux.org/v4l.shtml>.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called ibmcam.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>. This
camera has several configuration options which can be specified when
you load the module. Read <file:Documentation/usb/ibmcam.txt> to
learn more.
CONFIG_USB_KONICAWC
Say Y here if you want support for webcams based on a Konica
chipset. This is known to work with the Intel YC76 webcam.
This driver uses the Video For Linux API. You must enable
(Y or M in config) Video For Linux (under Character Devices)
to use this driver. Information on this API and pointers to
"v4l" programs may be found on the WWW at
<http://roadrunner.swansea.uk.linux.org/v4l.shtml>.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called konicawc.o. If you want to compile it as
a module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_OV511
Say Y here if you want to connect this type of camera to your
computer's USB port. See <file:Documentation/usb/ov511.txt> for more
information and for a list of supported cameras.
This driver uses the Video For Linux API. You must say Y or M to
"Video For Linux" (under Character Devices) to use this driver.
Information on this API and pointers to "v4l" programs may be found
on the WWW at <http://roadrunner.swansea.uk.linux.org/v4l.shtml>.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called ov511.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_PWC
Say Y or M here if you want to use one of these Philips USB webcams:
PCA645, PCA646, PCVC675, PCVC680, PCVC690, PCVC730, PCVC740, or
the Askey VC010. The PCA635, PCVC665 and PCVC720 are not supported
by this driver and never will be.
This driver has an optional plugin, which is distributed as a binary
module only. It contains code that allow you to use higher
resolutions and framerates but may not be distributed as source.
But even without this plugin you can these cams for most
applications.
See <file:Documentation/usb/philips.txt> for more information and
installation instructions.
The built-in microphone is enabled by selecting USB Audio support.
This driver uses the Video For Linux API. You must say Y or M to
"Video For Linux" (under Character Devices) to use this driver.
Information on this API and pointers to "v4l" programs may be found
on the WWW at <http://roadrunner.swansea.uk.linux.org/v4l.shtml>.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called pwc.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_SE401
Say Y here if you want to connect this type of camera to your
computer's USB port. See <file:Documentation/usb/se401.txt> for more
information and for a list of supported cameras.
This driver uses the Video For Linux API. You must say Y or M to
"Video For Linux" (under Multimedia Devices) to use this driver.
Information on this API and pointers to "v4l" programs may be found
on the WWW at <http://roadrunner.swansea.uk.linux.org/v4l.shtml>.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called se401.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_STV680
Say Y here if you want to connect this type of camera to your
computer's USB port. This includes the Pencam line of cameras.
See <file:Documentation/usb/stv680.txt> for more information and for
a list of supported cameras.
This driver uses the Video For Linux API. You must say Y or M to
"Video For Linux" (under Multimedia Devices) to use this driver.
Information on this API and pointers to "v4l" programs may be found
on the WWW at <http://roadrunner.swansea.uk.linux.org/v4l.shtml>.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called stv680.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_VICAM
Say Y here if you have 3com homeconnect camera (vicam).
This driver uses the Video For Linux API. You must say Y or M to
"Video For Linux" (under Multimedia Devices) to use this driver.
Information on this API and pointers to "v4l" programs may be found
on the WWW at <http://roadrunner.swansea.uk.linux.org/v4l.shtml>.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called vicam.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
drivers/usb/misc/Config.help 0 → 100644
View file @ 806af7cc
CONFIG_USB_AUERSWALD
Say Y here if you want to connect an Auerswald USB ISDN Device
to your computer's USB port.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called auerswald.o. If you want to compile it as
a module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_EMI26
This driver loads firmware to Emagic EMI 2|6 low latency USB
Audio interface.
After firmware load the device is handled with standard linux
USB Audio driver.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called audio.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_RIO500
Say Y here if you want to connect a USB Rio500 mp3 player to your
computer's USB port. Please read <file:Documentation/usb/rio.txt>
for more information.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called rio500.o. If you want to compile it as
a module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_TIGL
If you own a Texas Instruments graphing calculator and use a
TI-GRAPH LINK USB cable (aka SilverLink), then you might be
interested in this driver.
If you enable this driver, you will be able to communicate with
your calculator through a set of device nodes under /dev.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called tiglusb.o. If you want to compile it as a
module, say M here and read Documentation/modules.txt.
If you don't know what the SilverLink cable is or what a Texas
Instruments graphing calculator is, then you probably don't need this
driver.
If unsure, say N.
CONFIG_USB_USS720
This driver is for USB parallel port adapters that use the Lucent
Technologies USS-720 chip. These cables are plugged into your USB
port and provide USB compatibility to peripherals designed with
parallel port interfaces.
The chip has two modes: automatic mode and manual mode. In automatic
mode, it looks to the computer like a standard USB printer. Only
printers may be connected to the USS-720 in this mode. The generic
USB printer driver ("USB Printer support", above) may be used in
that mode, and you can say N here if you want to use the chip only
in this mode.
Manual mode is not limited to printers, any parallel port
device should work. This driver utilizes manual mode.
Note however that some operations are three orders of magnitude
slower than on a PCI/ISA Parallel Port, so timing critical
applications might not work.
Say Y here if you own an USS-720 USB->Parport cable and intend to
connect anything other than a printer to it.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called uss720.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
drivers/usb/net/Config.help 0 → 100644
View file @ 806af7cc
CONFIG_USB_CATC
Say Y if you want to use one of the following 10Mbps USB Ethernet
device based on the EL1210A chip. Supported devices are:
Belkin F5U011
Belkin F5U111
CATC NetMate
CATC NetMate II
smartBridges smartNIC
This driver makes the adapter appear as a normal Ethernet interface,
typically on eth0, if it is the only ethernet device, or perhaps on
eth1, if you have a PCI or ISA ethernet card installed.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called catc.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_CDCETHER
This driver supports devices conforming to the Communication Device
Class Ethernet Control Model. This is used in some cable modems.
For more details on the specification, get the Communication Device
Class specification from <http://www.usb.org/>.
This driver should work with the following devices:
* Ericsson PipeRider (all variants)
* Motorola (DM100 and SB4100)
* Broadcom Cable Modem (reference design)
* Toshiba PCX1100U and possibly other cable modems
The device creates a network device (ethX, where X depends on what
other networking devices you have in use), as for a normal PCI
or ISA based ethernet network card.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called cdc-ether.o. If you want to compile it
as a module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_KAWETH
Say Y here if you want to use one of the following 10Mbps only
USB Ethernet adapters based on the KLSI KL5KUSB101B chipset:
3Com 3C19250
ADS USB-10BT
ATEN USB Ethernet
ASANTE USB To Ethernet Adapter
AOX Endpoints USB Ethernet
Correga K.K.
D-Link DSB-650C and DU-E10
Entrega / Portgear E45
I-O DATA USB-ET/T
Jaton USB Ethernet Device Adapter
Kingston Technology USB Ethernet Adapter
Linksys USB10T
Mobility USB-Ethernet Adapter
NetGear EA-101
Peracom Enet and Enet2
Portsmith Express Ethernet Adapter
Shark Pocket Adapter
SMC 2202USB
Sony Vaio port extender
This driver is likely to work with most 10Mbps only USB Ethernet
adapters, including some "no brand" devices. It does NOT work on
SmartBridges smartNIC or on Belkin F5U111 devices - you should use
the CATC NetMate driver for those. If you are not sure which one
you need, select both, and the correct one should be selected for
you.
This driver makes the adapter appear as a normal Ethernet interface,
typically on eth0, if it is the only ethernet device, or perhaps on
eth1, if you have a PCI or ISA ethernet card installed.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called kaweth.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_PEGASUS
Say Y here if you know you have Pegasus or Pegasus-II based adapter.
If in doubt then look at linux/drivers/usb/pegasus.h for the complete
list of supported devices.
If your particular adapter is not in the list and you are _sure_ it
is Pegasus or Pegasus II based then send me (petkan@users.sourceforge.net)
vendor and device IDs.
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called pegasus.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_RTL8150
Say Y here if you have RTL8150 based usb-ethernet adapter.
Send me (petkan@users.sourceforge.net) any comments you may have.
You can also check for updates at http://pegasus2.sourceforge.net/
This code is also available as a module ( = code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called rtl8150.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
CONFIG_USB_USBNET
This driver supports network links over USB with USB "Network"
or "data transfer" cables, often used to network laptops to PCs.
Such cables have chips from suppliers such as Belkin/eTEK, GeneSys
(GeneLink), NetChip and Prolific. Intelligent USB devices could also
use this approach to provide Internet access, using standard USB
cabling. You can find these chips also on some motherboards with
USB PC2PC support.
These links will have names like "usb0", "usb1", etc. They act
like two-node Ethernets, so you can use 802.1d Ethernet Bridging
(CONFIG_BRIDGE) to simplify your network routing.
This code is also available as a kernel module (code which can be
inserted in and removed from the running kernel whenever you want).
The module will be called usbnet.o. If you want to compile it as a
module, say M here and read <file:Documentation/modules.txt>.
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7