Merge branch 'ksz9477-dsa-switch-driver-improvements'

Paul Barker says:

====================
ksz9477 dsa switch driver improvements

These changes were made while debugging the ksz9477 driver for use on a
custom board which uses the ksz9893 switch supported by this driver. The
patches have been runtime tested on top of Linux 5.8.4, I couldn't
runtime test them on top of 5.9-rc3 due to unrelated issues. They have
been build tested on top of net-next.

These changes can also be pulled from:

  https://gitlab.com/pbarker.dev/staging/linux.git
  tag: for-net-next/ksz-v3_2020-09-09

Changes from v2:

  * Fixed incorrect type in assignment error.
Reported-by: kernel test robot <lkp@intel.com>

Changes from v1:

  * Rebased onto net-next.

  * Dropped unnecessary `#include <linux/printk.h>`.

  * Instead of printing the phy mode in `ksz9477_port_setup()`, modify
    the existing print in `ksz9477_config_cpu_port()` to always produce
    output and to be more clear.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/dsa/microchip/ksz9477.c

@@ -1235,6 +1235,9 @@ static void ksz9477_port_setup(struct ksz_device *dev, int port, bool cpu_port)
 			if (dev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
 			    dev->interface == PHY_INTERFACE_MODE_RGMII_TXID)
 				data8 |= PORT_RGMII_ID_EG_ENABLE;
+			/* On KSZ9893, disable RGMII in-band status support */
+			if (dev->features & IS_9893)
+				data8 &= ~PORT_MII_MAC_MODE;
 			p->phydev.speed = SPEED_1000;
 			break;
 		}
@@ -1265,6 +1268,8 @@ static void ksz9477_config_cpu_port(struct dsa_switch *ds)
 	for (i = 0; i < dev->port_cnt; i++) {
 		if (dsa_is_cpu_port(ds, i) && (dev->cpu_ports & (1 << i))) {
 			phy_interface_t interface;
+			const char *prev_msg;
+			const char *prev_mode;
 
 			dev->cpu_port = i;
 			dev->host_mask = (1 << dev->cpu_port);
@@ -1277,11 +1282,19 @@ static void ksz9477_config_cpu_port(struct dsa_switch *ds)
 			interface = ksz9477_get_interface(dev, i);
 			if (!dev->interface)
 				dev->interface = interface;
-			if (interface && interface != dev->interface)
+			if (interface && interface != dev->interface) {
+				prev_msg = " instead of ";
+				prev_mode = phy_modes(interface);
+			} else {
+				prev_msg = "";
+				prev_mode = "";
+			}
 			dev_info(dev->dev,
-					 "use %s instead of %s\n",
+				 "Port%d: using phy mode %s%s%s\n",
+				 i,
 				 phy_modes(dev->interface),
-					  phy_modes(interface));
+				 prev_msg,
+				 prev_mode);
 
 			/* enable cpu port */
 			ksz9477_port_setup(dev, i, true);
@@ -1426,10 +1439,12 @@ static int ksz9477_switch_detect(struct ksz_device *dev)
 	/* Default capability is gigabit capable. */
 	dev->features = GBIT_SUPPORT;
 
+	dev_dbg(dev->dev, "Switch detect: ID=%08x%02x\n", id32, data8);
 	id_hi = (u8)(id32 >> 16);
 	id_lo = (u8)(id32 >> 8);
 	if ((id_lo & 0xf) == 3) {
 		/* Chip is from KSZ9893 design. */
+		dev_info(dev->dev, "Found KSZ9893\n");
 		dev->features |= IS_9893;
 
 		/* Chip does not support gigabit. */
@@ -1438,6 +1453,7 @@ static int ksz9477_switch_detect(struct ksz_device *dev)
 		dev->mib_port_cnt = 3;
 		dev->phy_port_cnt = 2;
 	} else {
+		dev_info(dev->dev, "Found KSZ9477 or compatible\n");
 		/* Chip uses new XMII register definitions. */
 		dev->features |= NEW_XMII;
 

drivers/net/dsa/microchip/ksz_common.c

@@ -400,8 +400,9 @@ int ksz_switch_register(struct ksz_device *dev,
 
 	if (dev->reset_gpio) {
 		gpiod_set_value_cansleep(dev->reset_gpio, 1);
-		mdelay(10);
+		usleep_range(10000, 12000);
 		gpiod_set_value_cansleep(dev->reset_gpio, 0);
+		usleep_range(100, 1000);
 	}
 
 	mutex_init(&dev->dev_mutex);