Merge tag 'spi-fix-v5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi fixes from Mark Brown:
 "A small collection of fixes for SPI, small mostly driver specific
  things plus a fix for module autoloading which hadn't been working
  properly for DT systems"

* tag 'spi-fix-v5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: cadence-quadspi: Fix check condition for DTR ops
  spi: mediatek: Fix fifo transfer
  spi: imx: mx51-ecspi: Fix CONFIGREG delay comment
  spi: imx: mx51-ecspi: Fix low-speed CONFIGREG delay calculation
  spi: update modalias_show after of_device_uevent_modalias support
  spi: meson-spicc: fix memory leak in meson_spicc_remove
  spi: spi-mux: Add module info needed for autoloading

drivers/spi/spi-cadence-quadspi.c

@@ -325,7 +325,15 @@ static int cqspi_set_protocol(struct cqspi_flash_pdata *f_pdata,
 	f_pdata->inst_width = CQSPI_INST_TYPE_SINGLE;
 	f_pdata->addr_width = CQSPI_INST_TYPE_SINGLE;
 	f_pdata->data_width = CQSPI_INST_TYPE_SINGLE;
-	f_pdata->dtr = op->data.dtr && op->cmd.dtr && op->addr.dtr;
+
+	/*
+	 * For an op to be DTR, cmd phase along with every other non-empty
+	 * phase should have dtr field set to 1. If an op phase has zero
+	 * nbytes, ignore its dtr field; otherwise, check its dtr field.
+	 */
+	f_pdata->dtr = op->cmd.dtr &&
+		       (!op->addr.nbytes || op->addr.dtr) &&
+		       (!op->data.nbytes || op->data.dtr);
 
 	switch (op->data.buswidth) {
 	case 0:
@@ -1228,8 +1236,15 @@ static bool cqspi_supports_mem_op(struct spi_mem *mem,
 {
 	bool all_true, all_false;
 
-	all_true = op->cmd.dtr && op->addr.dtr && op->dummy.dtr &&
-		   op->data.dtr;
+	/*
+	 * op->dummy.dtr is required for converting nbytes into ncycles.
+	 * Also, don't check the dtr field of the op phase having zero nbytes.
+	 */
+	all_true = op->cmd.dtr &&
+		   (!op->addr.nbytes || op->addr.dtr) &&
+		   (!op->dummy.nbytes || op->dummy.dtr) &&
+		   (!op->data.nbytes || op->data.dtr);
+
 	all_false = !op->cmd.dtr && !op->addr.dtr && !op->dummy.dtr &&
 		    !op->data.dtr;
 

drivers/spi/spi-imx.c

@@ -505,7 +505,9 @@ static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx,
 				      struct spi_message *msg)
 {
 	struct spi_device *spi = msg->spi;
+	struct spi_transfer *xfer;
 	u32 ctrl = MX51_ECSPI_CTRL_ENABLE;
+	u32 min_speed_hz = ~0U;
 	u32 testreg, delay;
 	u32 cfg = readl(spi_imx->base + MX51_ECSPI_CONFIG);
 
@@ -577,9 +579,21 @@ static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx,
 	 * be asserted before the SCLK polarity changes, which would disrupt
 	 * the SPI communication as the device on the other end would consider
 	 * the change of SCLK polarity as a clock tick already.
+	 *
+	 * Because spi_imx->spi_bus_clk is only set in bitbang prepare_message
+	 * callback, iterate over all the transfers in spi_message, find the
+	 * one with lowest bus frequency, and use that bus frequency for the
+	 * delay calculation. In case all transfers have speed_hz == 0, then
+	 * min_speed_hz is ~0 and the resulting delay is zero.
 	 */
-	delay = (2 * 1000000) / spi_imx->spi_bus_clk;
-	if (likely(delay < 10))	/* SCLK is faster than 100 kHz */
+	list_for_each_entry(xfer, &msg->transfers, transfer_list) {
+		if (!xfer->speed_hz)
+			continue;
+		min_speed_hz = min(xfer->speed_hz, min_speed_hz);
+	}
+
+	delay = (2 * 1000000) / min_speed_hz;
+	if (likely(delay < 10))	/* SCLK is faster than 200 kHz */
 		udelay(delay);
 	else			/* SCLK is _very_ slow */
 		usleep_range(delay, delay + 10);

drivers/spi/spi-meson-spicc.c

@@ -785,6 +785,8 @@ static int meson_spicc_remove(struct platform_device *pdev)
 	clk_disable_unprepare(spicc->core);
 	clk_disable_unprepare(spicc->pclk);
 
+	spi_master_put(spicc->master);
+
 	return 0;
 }
 

drivers/spi/spi-mt65xx.c

@@ -426,24 +426,15 @@ static int mtk_spi_fifo_transfer(struct spi_master *master,
 	mtk_spi_prepare_transfer(master, xfer);
 	mtk_spi_setup_packet(master);
 
+	if (xfer->tx_buf) {
 		cnt = xfer->len / 4;
-	if (xfer->tx_buf)
 		iowrite32_rep(mdata->base + SPI_TX_DATA_REG, xfer->tx_buf, cnt);
-
-	if (xfer->rx_buf)
-		ioread32_rep(mdata->base + SPI_RX_DATA_REG, xfer->rx_buf, cnt);
-
 		remainder = xfer->len % 4;
 		if (remainder > 0) {
 			reg_val = 0;
-		if (xfer->tx_buf) {
 			memcpy(&reg_val, xfer->tx_buf + (cnt * 4), remainder);
 			writel(reg_val, mdata->base + SPI_TX_DATA_REG);
 		}
-		if (xfer->rx_buf) {
-			reg_val = readl(mdata->base + SPI_RX_DATA_REG);
-			memcpy(xfer->rx_buf + (cnt * 4), &reg_val, remainder);
-		}
 	}
 
 	mtk_spi_enable_transfer(master);

drivers/spi/spi-mux.c

@@ -167,10 +167,17 @@ static int spi_mux_probe(struct spi_device *spi)
 	return ret;
 }
 
+static const struct spi_device_id spi_mux_id[] = {
+	{ "spi-mux" },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, spi_mux_id);
+
 static const struct of_device_id spi_mux_of_match[] = {
 	{ .compatible = "spi-mux" },
 	{ }
 };
+MODULE_DEVICE_TABLE(of, spi_mux_of_match);
 
 static struct spi_driver spi_mux_driver = {
 	.probe  = spi_mux_probe,
@@ -178,6 +185,7 @@ static struct spi_driver spi_mux_driver = {
 		.name   = "spi-mux",
 		.of_match_table = spi_mux_of_match,
 	},
+	.id_table = spi_mux_id,
 };
 
 module_spi_driver(spi_mux_driver);

drivers/spi/spi.c

@@ -58,6 +58,10 @@ modalias_show(struct device *dev, struct device_attribute *a, char *buf)
 	const struct spi_device	*spi = to_spi_device(dev);
 	int len;
 
+	len = of_device_modalias(dev, buf, PAGE_SIZE);
+	if (len != -ENODEV)
+		return len;
+
 	len = acpi_device_modalias(dev, buf, PAGE_SIZE - 1);
 	if (len != -ENODEV)
 		return len;