fsi: Move defines to common header

The FSI master registers are common to the hub and AST2600 master (and
the FSP2, if someone was to upstream a driver for that).

Add defines to the fsi-master.h header, and introduce headings to
delineate the existing low level details.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20191108051945.7109-8-joel@jms.id.auSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/fsi/fsi-master-hub.c

@@ -13,53 +13,7 @@
 
 #include "fsi-master.h"
 
-/* Control Registers */
-#define FSI_MMODE		0x0		/* R/W: mode */
-#define FSI_MDLYR		0x4		/* R/W: delay */
-#define FSI_MCRSP		0x8		/* R/W: clock rate */
-#define FSI_MENP0		0x10		/* R/W: enable */
-#define FSI_MLEVP0		0x18		/* R: plug detect */
-#define FSI_MSENP0		0x18		/* S: Set enable */
-#define FSI_MCENP0		0x20		/* C: Clear enable */
-#define FSI_MAEB		0x70		/* R: Error address */
-#define FSI_MVER		0x74		/* R: master version/type */
-#define FSI_MRESP0		0xd0		/* W: Port reset */
-#define FSI_MESRB0		0x1d0		/* R: Master error status */
-#define FSI_MRESB0		0x1d0		/* W: Reset bridge */
-#define FSI_MECTRL		0x2e0		/* W: Error control */
-
-/* MMODE: Mode control */
-#define FSI_MMODE_EIP		0x80000000	/* Enable interrupt polling */
-#define FSI_MMODE_ECRC		0x40000000	/* Enable error recovery */
-#define FSI_MMODE_EPC		0x10000000	/* Enable parity checking */
-#define FSI_MMODE_P8_TO_LSB	0x00000010	/* Timeout value LSB */
-						/*   MSB=1, LSB=0 is 0.8 ms */
-						/*   MSB=0, LSB=1 is 0.9 ms */
-#define FSI_MMODE_CRS0SHFT	18		/* Clk rate selection 0 shift */
-#define FSI_MMODE_CRS0MASK	0x3ff		/* Clk rate selection 0 mask */
-#define FSI_MMODE_CRS1SHFT	8		/* Clk rate selection 1 shift */
-#define FSI_MMODE_CRS1MASK	0x3ff		/* Clk rate selection 1 mask */
-
-/* MRESB: Reset brindge */
-#define FSI_MRESB_RST_GEN	0x80000000	/* General reset */
-#define FSI_MRESB_RST_ERR	0x40000000	/* Error Reset */
-
-/* MRESB: Reset port */
-#define FSI_MRESP_RST_ALL_MASTER 0x20000000	/* Reset all FSI masters */
-#define FSI_MRESP_RST_ALL_LINK	0x10000000	/* Reset all FSI port contr. */
-#define FSI_MRESP_RST_MCR	0x08000000	/* Reset FSI master reg. */
-#define FSI_MRESP_RST_PYE	0x04000000	/* Reset FSI parity error */
-#define FSI_MRESP_RST_ALL	0xfc000000	/* Reset any error */
-
-/* MECTRL: Error control */
-#define FSI_MECTRL_EOAE		0x8000		/* Enable machine check when */
-						/* master 0 in error */
-#define FSI_MECTRL_P8_AUTO_TERM	0x4000		/* Auto terminate */
-
 #define FSI_ENGID_HUB_MASTER		0x1c
-#define FSI_HUB_LINK_OFFSET		0x80000
-#define FSI_HUB_LINK_SIZE		0x80000
-#define FSI_HUB_MASTER_MAX_LINKS	8
 
 #define FSI_LINK_ENABLE_SETUP_TIME	10	/* in mS */
 

drivers/fsi/fsi-master.h

@@ -12,6 +12,71 @@
 #include <linux/device.h>
 #include <linux/mutex.h>
 
+/*
+ * Master registers
+ *
+ * These are used by hardware masters, such as the one in the FSP2, AST2600 and
+ * the hub master in POWER processors.
+ */
+
+/* Control Registers */
+#define FSI_MMODE		0x0		/* R/W: mode */
+#define FSI_MDLYR		0x4		/* R/W: delay */
+#define FSI_MCRSP		0x8		/* R/W: clock rate */
+#define FSI_MENP0		0x10		/* R/W: enable */
+#define FSI_MLEVP0		0x18		/* R: plug detect */
+#define FSI_MSENP0		0x18		/* S: Set enable */
+#define FSI_MCENP0		0x20		/* C: Clear enable */
+#define FSI_MAEB		0x70		/* R: Error address */
+#define FSI_MVER		0x74		/* R: master version/type */
+#define FSI_MSTAP0		0xd0		/* R: Port status */
+#define FSI_MRESP0		0xd0		/* W: Port reset */
+#define FSI_MESRB0		0x1d0		/* R: Master error status */
+#define FSI_MRESB0		0x1d0		/* W: Reset bridge */
+#define FSI_MSCSB0		0x1d4		/* R: Master sub command stack */
+#define FSI_MATRB0		0x1d8		/* R: Master address trace */
+#define FSI_MDTRB0		0x1dc		/* R: Master data trace */
+#define FSI_MECTRL		0x2e0		/* W: Error control */
+
+/* MMODE: Mode control */
+#define FSI_MMODE_EIP		0x80000000	/* Enable interrupt polling */
+#define FSI_MMODE_ECRC		0x40000000	/* Enable error recovery */
+#define FSI_MMODE_RELA		0x20000000	/* Enable relative address commands */
+#define FSI_MMODE_EPC		0x10000000	/* Enable parity checking */
+#define FSI_MMODE_P8_TO_LSB	0x00000010	/* Timeout value LSB */
+						/*   MSB=1, LSB=0 is 0.8 ms */
+						/*   MSB=0, LSB=1 is 0.9 ms */
+#define FSI_MMODE_CRS0SHFT	18		/* Clk rate selection 0 shift */
+#define FSI_MMODE_CRS0MASK	0x3ff		/* Clk rate selection 0 mask */
+#define FSI_MMODE_CRS1SHFT	8		/* Clk rate selection 1 shift */
+#define FSI_MMODE_CRS1MASK	0x3ff		/* Clk rate selection 1 mask */
+
+/* MRESB: Reset brindge */
+#define FSI_MRESB_RST_GEN	0x80000000	/* General reset */
+#define FSI_MRESB_RST_ERR	0x40000000	/* Error Reset */
+
+/* MRESP: Reset port */
+#define FSI_MRESP_RST_ALL_MASTER 0x20000000	/* Reset all FSI masters */
+#define FSI_MRESP_RST_ALL_LINK	0x10000000	/* Reset all FSI port contr. */
+#define FSI_MRESP_RST_MCR	0x08000000	/* Reset FSI master reg. */
+#define FSI_MRESP_RST_PYE	0x04000000	/* Reset FSI parity error */
+#define FSI_MRESP_RST_ALL	0xfc000000	/* Reset any error */
+
+/* MECTRL: Error control */
+#define FSI_MECTRL_EOAE		0x8000		/* Enable machine check when */
+						/* master 0 in error */
+#define FSI_MECTRL_P8_AUTO_TERM	0x4000		/* Auto terminate */
+
+#define FSI_HUB_LINK_OFFSET		0x80000
+#define FSI_HUB_LINK_SIZE		0x80000
+#define FSI_HUB_MASTER_MAX_LINKS	8
+
+/*
+ * Protocol definitions
+ *
+ * These are used by low level masters that bit-bang out the protocol
+ */
+
 /* Various protocol delays */
 #define	FSI_ECHO_DELAY_CLOCKS	16	/* Number clocks for echo delay */
 #define	FSI_SEND_DELAY_CLOCKS	16	/* Number clocks for send delay */
@@ -47,6 +112,12 @@
 /* fsi-master definition and flags */
 #define FSI_MASTER_FLAG_SWCLOCK		0x1
 
+/*
+ * Structures and function prototypes
+ *
+ * These are common to all masters
+ */
+
 struct fsi_master {
 	struct device	dev;
 	int		idx;