Commit 8bd22949 authored by Kevin Hilman's avatar Kevin Hilman

OMAP2/3: PM: push core PM code from linux-omap

This patch is to sync the core linux-omap PM code with mainline.  This
code has evolved and been used for a while the linux-omap tree, but
the attempt here is to finally get this into mainline.

Following this will be a series of patches from the 'PM branch' of the
linux-omap tree to add full PM hardware support from the linux-omap
tree.

Much of this PM core code was written by Jouni Hogander with
significant contributions from Paul Walmsley as well as many others
from Nokia, Texas Instruments and linux-omap community.
Signed-off-by: default avatarJouni Hogander <jouni.hogander@nokia.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: default avatarKevin Hilman <khilman@deeprootsystems.com>
parent a330bd47
......@@ -25,8 +25,10 @@ obj-$(CONFIG_ARCH_OMAP2) += sdrc2xxx.o
# Power Management
ifeq ($(CONFIG_PM),y)
obj-y += pm.o
obj-$(CONFIG_ARCH_OMAP2) += pm24xx.o
obj-$(CONFIG_ARCH_OMAP24XX) += sleep24xx.o
obj-$(CONFIG_ARCH_OMAP3) += pm34xx.o sleep34xx.o
obj-$(CONFIG_PM_DEBUG) += pm-debug.o
endif
# Clock framework
......
/*
* OMAP Power Management debug routines
*
* Copyright (C) 2005 Texas Instruments, Inc.
* Copyright (C) 2006-2008 Nokia Corporation
*
* Written by:
* Richard Woodruff <r-woodruff2@ti.com>
* Tony Lindgren
* Juha Yrjola
* Amit Kucheria <amit.kucheria@nokia.com>
* Igor Stoppa <igor.stoppa@nokia.com>
* Jouni Hogander
*
* Based on pm.c for omap2
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/timer.h>
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/io.h>
#include <mach/clock.h>
#include <mach/board.h>
#include "prm.h"
#include "cm.h"
#include "pm.h"
int omap2_pm_debug;
#define DUMP_PRM_MOD_REG(mod, reg) \
regs[reg_count].name = #mod "." #reg; \
regs[reg_count++].val = prm_read_mod_reg(mod, reg)
#define DUMP_CM_MOD_REG(mod, reg) \
regs[reg_count].name = #mod "." #reg; \
regs[reg_count++].val = cm_read_mod_reg(mod, reg)
#define DUMP_PRM_REG(reg) \
regs[reg_count].name = #reg; \
regs[reg_count++].val = __raw_readl(reg)
#define DUMP_CM_REG(reg) \
regs[reg_count].name = #reg; \
regs[reg_count++].val = __raw_readl(reg)
#define DUMP_INTC_REG(reg, off) \
regs[reg_count].name = #reg; \
regs[reg_count++].val = __raw_readl(IO_ADDRESS(0x480fe000 + (off)))
void omap2_pm_dump(int mode, int resume, unsigned int us)
{
struct reg {
const char *name;
u32 val;
} regs[32];
int reg_count = 0, i;
const char *s1 = NULL, *s2 = NULL;
if (!resume) {
#if 0
/* MPU */
DUMP_PRM_MOD_REG(OCP_MOD, OMAP2_PRM_IRQENABLE_MPU_OFFSET);
DUMP_CM_MOD_REG(MPU_MOD, CM_CLKSTCTRL);
DUMP_PRM_MOD_REG(MPU_MOD, PM_PWSTCTRL);
DUMP_PRM_MOD_REG(MPU_MOD, PM_PWSTST);
DUMP_PRM_MOD_REG(MPU_MOD, PM_WKDEP);
#endif
#if 0
/* INTC */
DUMP_INTC_REG(INTC_MIR0, 0x0084);
DUMP_INTC_REG(INTC_MIR1, 0x00a4);
DUMP_INTC_REG(INTC_MIR2, 0x00c4);
#endif
#if 0
DUMP_CM_MOD_REG(CORE_MOD, CM_FCLKEN1);
if (cpu_is_omap24xx()) {
DUMP_CM_MOD_REG(CORE_MOD, OMAP24XX_CM_FCLKEN2);
DUMP_PRM_MOD_REG(OMAP24XX_GR_MOD,
OMAP2_PRCM_CLKEMUL_CTRL_OFFSET);
DUMP_PRM_MOD_REG(OMAP24XX_GR_MOD,
OMAP2_PRCM_CLKSRC_CTRL_OFFSET);
}
DUMP_CM_MOD_REG(WKUP_MOD, CM_FCLKEN);
DUMP_CM_MOD_REG(CORE_MOD, CM_ICLKEN1);
DUMP_CM_MOD_REG(CORE_MOD, CM_ICLKEN2);
DUMP_CM_MOD_REG(WKUP_MOD, CM_ICLKEN);
DUMP_CM_MOD_REG(PLL_MOD, CM_CLKEN);
DUMP_CM_MOD_REG(PLL_MOD, CM_AUTOIDLE);
DUMP_PRM_MOD_REG(CORE_MOD, PM_PWSTST);
#endif
#if 0
/* DSP */
if (cpu_is_omap24xx()) {
DUMP_CM_MOD_REG(OMAP24XX_DSP_MOD, CM_FCLKEN);
DUMP_CM_MOD_REG(OMAP24XX_DSP_MOD, CM_ICLKEN);
DUMP_CM_MOD_REG(OMAP24XX_DSP_MOD, CM_IDLEST);
DUMP_CM_MOD_REG(OMAP24XX_DSP_MOD, CM_AUTOIDLE);
DUMP_CM_MOD_REG(OMAP24XX_DSP_MOD, CM_CLKSEL);
DUMP_CM_MOD_REG(OMAP24XX_DSP_MOD, CM_CLKSTCTRL);
DUMP_PRM_MOD_REG(OMAP24XX_DSP_MOD, RM_RSTCTRL);
DUMP_PRM_MOD_REG(OMAP24XX_DSP_MOD, RM_RSTST);
DUMP_PRM_MOD_REG(OMAP24XX_DSP_MOD, PM_PWSTCTRL);
DUMP_PRM_MOD_REG(OMAP24XX_DSP_MOD, PM_PWSTST);
}
#endif
} else {
DUMP_PRM_MOD_REG(CORE_MOD, PM_WKST1);
if (cpu_is_omap24xx())
DUMP_PRM_MOD_REG(CORE_MOD, OMAP24XX_PM_WKST2);
DUMP_PRM_MOD_REG(WKUP_MOD, PM_WKST);
DUMP_PRM_MOD_REG(OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
#if 1
DUMP_INTC_REG(INTC_PENDING_IRQ0, 0x0098);
DUMP_INTC_REG(INTC_PENDING_IRQ1, 0x00b8);
DUMP_INTC_REG(INTC_PENDING_IRQ2, 0x00d8);
#endif
}
switch (mode) {
case 0:
s1 = "full";
s2 = "retention";
break;
case 1:
s1 = "MPU";
s2 = "retention";
break;
case 2:
s1 = "MPU";
s2 = "idle";
break;
}
if (!resume)
#ifdef CONFIG_NO_HZ
printk(KERN_INFO
"--- Going to %s %s (next timer after %u ms)\n", s1, s2,
jiffies_to_msecs(get_next_timer_interrupt(jiffies) -
jiffies));
#else
printk(KERN_INFO "--- Going to %s %s\n", s1, s2);
#endif
else
printk(KERN_INFO "--- Woke up (slept for %u.%03u ms)\n",
us / 1000, us % 1000);
for (i = 0; i < reg_count; i++)
printk(KERN_INFO "%-20s: 0x%08x\n", regs[i].name, regs[i].val);
}
/*
* linux/arch/arm/mach-omap2/pm.c
*
* OMAP2 Power Management Routines
*
* Copyright (C) 2006 Nokia Corporation
* Tony Lindgren <tony@atomide.com>
*
* Copyright (C) 2005 Texas Instruments, Inc.
* Richard Woodruff <r-woodruff2@ti.com>
*
* Based on pm.c for omap1
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/suspend.h>
#include <linux/sched.h>
#include <linux/proc_fs.h>
#include <linux/interrupt.h>
#include <linux/sysfs.h>
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/clk.h>
#include <linux/io.h>
#include <asm/irq.h>
#include <asm/atomic.h>
#include <asm/mach/time.h>
#include <asm/mach/irq.h>
#include <mach/irqs.h>
#include <mach/clock.h>
#include <mach/sram.h>
#include <mach/pm.h>
static struct clk *vclk;
static void (*omap2_sram_idle)(void);
static void (*omap2_sram_suspend)(int dllctrl, int cpu_rev);
static void (*saved_idle)(void);
extern void __init pmdomain_init(void);
extern void pmdomain_set_autoidle(void);
static unsigned int omap24xx_sleep_save[OMAP24XX_SLEEP_SAVE_SIZE];
void omap2_pm_idle(void)
{
local_irq_disable();
local_fiq_disable();
if (need_resched()) {
local_fiq_enable();
local_irq_enable();
return;
}
omap2_sram_idle();
local_fiq_enable();
local_irq_enable();
}
static int omap2_pm_prepare(void)
{
/* We cannot sleep in idle until we have resumed */
saved_idle = pm_idle;
pm_idle = NULL;
return 0;
}
static int omap2_pm_suspend(void)
{
return 0;
}
static int omap2_pm_enter(suspend_state_t state)
{
int ret = 0;
switch (state)
{
case PM_SUSPEND_STANDBY:
case PM_SUSPEND_MEM:
ret = omap2_pm_suspend();
break;
default:
ret = -EINVAL;
}
return ret;
}
static void omap2_pm_finish(void)
{
pm_idle = saved_idle;
}
static struct platform_suspend_ops omap_pm_ops = {
.prepare = omap2_pm_prepare,
.enter = omap2_pm_enter,
.finish = omap2_pm_finish,
.valid = suspend_valid_only_mem,
};
static int __init omap2_pm_init(void)
{
return 0;
}
__initcall(omap2_pm_init);
/*
* OMAP2/3 Power Management Routines
*
* Copyright (C) 2008 Nokia Corporation
* Jouni Hogander
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#ifndef __ARCH_ARM_MACH_OMAP2_PM_H
#define __ARCH_ARM_MACH_OMAP2_PM_H
extern int omap2_pm_init(void);
extern int omap3_pm_init(void);
#ifdef CONFIG_PM_DEBUG
extern void omap2_pm_dump(int mode, int resume, unsigned int us);
extern int omap2_pm_debug;
#else
#define omap2_pm_dump(mode, resume, us) do {} while (0);
#define omap2_pm_debug 0
#endif /* CONFIG_PM_DEBUG */
extern void omap24xx_idle_loop_suspend(void);
extern void omap24xx_cpu_suspend(u32 dll_ctrl, void __iomem *sdrc_dlla_ctrl,
void __iomem *sdrc_power);
extern void omap34xx_cpu_suspend(u32 *addr, int save_state);
extern void save_secure_ram_context(u32 *addr);
extern unsigned int omap24xx_idle_loop_suspend_sz;
extern unsigned int omap34xx_suspend_sz;
extern unsigned int save_secure_ram_context_sz;
extern unsigned int omap24xx_cpu_suspend_sz;
extern unsigned int omap34xx_cpu_suspend_sz;
#endif
/*
* OMAP2 Power Management Routines
*
* Copyright (C) 2005 Texas Instruments, Inc.
* Copyright (C) 2006-2008 Nokia Corporation
*
* Written by:
* Richard Woodruff <r-woodruff2@ti.com>
* Tony Lindgren
* Juha Yrjola
* Amit Kucheria <amit.kucheria@nokia.com>
* Igor Stoppa <igor.stoppa@nokia.com>
*
* Based on pm.c for omap1
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/suspend.h>
#include <linux/sched.h>
#include <linux/proc_fs.h>
#include <linux/interrupt.h>
#include <linux/sysfs.h>
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/clk.h>
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/time.h>
#include <linux/gpio.h>
#include <asm/mach/time.h>
#include <asm/mach/irq.h>
#include <asm/mach-types.h>
#include <mach/irqs.h>
#include <mach/clock.h>
#include <mach/sram.h>
#include <mach/control.h>
#include <mach/mux.h>
#include <mach/dma.h>
#include <mach/board.h>
#include "prm.h"
#include "prm-regbits-24xx.h"
#include "cm.h"
#include "cm-regbits-24xx.h"
#include "sdrc.h"
#include "pm.h"
#include <mach/powerdomain.h>
#include <mach/clockdomain.h>
static void (*omap2_sram_idle)(void);
static void (*omap2_sram_suspend)(u32 dllctrl, void __iomem *sdrc_dlla_ctrl,
void __iomem *sdrc_power);
static struct powerdomain *mpu_pwrdm;
static struct powerdomain *core_pwrdm;
static struct clockdomain *dsp_clkdm;
static struct clockdomain *gfx_clkdm;
static struct clk *osc_ck, *emul_ck;
static int omap2_fclks_active(void)
{
u32 f1, f2;
f1 = cm_read_mod_reg(CORE_MOD, CM_FCLKEN1);
f2 = cm_read_mod_reg(CORE_MOD, OMAP24XX_CM_FCLKEN2);
if (f1 | f2)
return 1;
return 0;
}
static int omap2_irq_pending(void)
{
u32 pending_reg = 0x480fe098;
int i;
for (i = 0; i < 4; i++) {
if (omap_readl(pending_reg))
return 1;
pending_reg += 0x20;
}
return 0;
}
static void omap2_enter_full_retention(void)
{
u32 l;
struct timespec ts_preidle, ts_postidle, ts_idle;
/* There is 1 reference hold for all children of the oscillator
* clock, the following will remove it. If no one else uses the
* oscillator itself it will be disabled if/when we enter retention
* mode.
*/
clk_disable(osc_ck);
/* Clear old wake-up events */
/* REVISIT: These write to reserved bits? */
prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
prm_write_mod_reg(0xffffffff, WKUP_MOD, PM_WKST);
/*
* Set MPU powerdomain's next power state to RETENTION;
* preserve logic state during retention
*/
pwrdm_set_logic_retst(mpu_pwrdm, PWRDM_POWER_RET);
pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);
/* Workaround to kill USB */
l = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0) | OMAP24XX_USBSTANDBYCTRL;
omap_ctrl_writel(l, OMAP2_CONTROL_DEVCONF0);
omap2_gpio_prepare_for_retention();
if (omap2_pm_debug) {
omap2_pm_dump(0, 0, 0);
getnstimeofday(&ts_preidle);
}
/* One last check for pending IRQs to avoid extra latency due
* to sleeping unnecessarily. */
if (omap2_irq_pending())
goto no_sleep;
/* Jump to SRAM suspend code */
omap2_sram_suspend(sdrc_read_reg(SDRC_DLLA_CTRL),
OMAP_SDRC_REGADDR(SDRC_DLLA_CTRL),
OMAP_SDRC_REGADDR(SDRC_POWER));
no_sleep:
if (omap2_pm_debug) {
unsigned long long tmp;
getnstimeofday(&ts_postidle);
ts_idle = timespec_sub(ts_postidle, ts_preidle);
tmp = timespec_to_ns(&ts_idle) * NSEC_PER_USEC;
omap2_pm_dump(0, 1, tmp);
}
omap2_gpio_resume_after_retention();
clk_enable(osc_ck);
/* clear CORE wake-up events */
prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
/* wakeup domain events - bit 1: GPT1, bit5 GPIO */
prm_clear_mod_reg_bits(0x4 | 0x1, WKUP_MOD, PM_WKST);
/* MPU domain wake events */
l = prm_read_mod_reg(OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
if (l & 0x01)
prm_write_mod_reg(0x01, OCP_MOD,
OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
if (l & 0x20)
prm_write_mod_reg(0x20, OCP_MOD,
OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
/* Mask future PRCM-to-MPU interrupts */
prm_write_mod_reg(0x0, OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
}
static int omap2_i2c_active(void)
{
u32 l;
l = cm_read_mod_reg(CORE_MOD, CM_FCLKEN1);
return l & (OMAP2420_EN_I2C2 | OMAP2420_EN_I2C1);
}
static int sti_console_enabled;
static int omap2_allow_mpu_retention(void)
{
u32 l;
/* Check for MMC, UART2, UART1, McSPI2, McSPI1 and DSS1. */
l = cm_read_mod_reg(CORE_MOD, CM_FCLKEN1);
if (l & (OMAP2420_EN_MMC | OMAP24XX_EN_UART2 |
OMAP24XX_EN_UART1 | OMAP24XX_EN_MCSPI2 |
OMAP24XX_EN_MCSPI1 | OMAP24XX_EN_DSS1))
return 0;
/* Check for UART3. */
l = cm_read_mod_reg(CORE_MOD, OMAP24XX_CM_FCLKEN2);
if (l & OMAP24XX_EN_UART3)
return 0;
if (sti_console_enabled)
return 0;
return 1;
}
static void omap2_enter_mpu_retention(void)
{
int only_idle = 0;
struct timespec ts_preidle, ts_postidle, ts_idle;
/* Putting MPU into the WFI state while a transfer is active
* seems to cause the I2C block to timeout. Why? Good question. */
if (omap2_i2c_active())
return;
/* The peripherals seem not to be able to wake up the MPU when
* it is in retention mode. */
if (omap2_allow_mpu_retention()) {
/* REVISIT: These write to reserved bits? */
prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
prm_write_mod_reg(0xffffffff, WKUP_MOD, PM_WKST);
/* Try to enter MPU retention */
prm_write_mod_reg((0x01 << OMAP_POWERSTATE_SHIFT) |
OMAP_LOGICRETSTATE,
MPU_MOD, PM_PWSTCTRL);
} else {
/* Block MPU retention */
prm_write_mod_reg(OMAP_LOGICRETSTATE, MPU_MOD, PM_PWSTCTRL);
only_idle = 1;
}
if (omap2_pm_debug) {
omap2_pm_dump(only_idle ? 2 : 1, 0, 0);
getnstimeofday(&ts_preidle);
}
omap2_sram_idle();
if (omap2_pm_debug) {
unsigned long long tmp;
getnstimeofday(&ts_postidle);
ts_idle = timespec_sub(ts_postidle, ts_preidle);
tmp = timespec_to_ns(&ts_idle) * NSEC_PER_USEC;
omap2_pm_dump(only_idle ? 2 : 1, 1, tmp);
}
}
static int omap2_can_sleep(void)
{
if (omap2_fclks_active())
return 0;
if (osc_ck->usecount > 1)
return 0;
if (omap_dma_running())
return 0;
return 1;
}
static void omap2_pm_idle(void)
{
local_irq_disable();
local_fiq_disable();
if (!omap2_can_sleep()) {
if (omap2_irq_pending())
goto out;
omap2_enter_mpu_retention();
goto out;
}
if (omap2_irq_pending())
goto out;
omap2_enter_full_retention();
out:
local_fiq_enable();
local_irq_enable();
}
static int omap2_pm_prepare(void)
{
/* We cannot sleep in idle until we have resumed */
disable_hlt();
return 0;
}
static int omap2_pm_suspend(void)
{
u32 wken_wkup, mir1;
wken_wkup = prm_read_mod_reg(WKUP_MOD, PM_WKEN);
prm_write_mod_reg(wken_wkup & ~OMAP24XX_EN_GPT1, WKUP_MOD, PM_WKEN);
/* Mask GPT1 */
mir1 = omap_readl(0x480fe0a4);
omap_writel(1 << 5, 0x480fe0ac);
omap2_enter_full_retention();
omap_writel(mir1, 0x480fe0a4);
prm_write_mod_reg(wken_wkup, WKUP_MOD, PM_WKEN);
return 0;
}
static int omap2_pm_enter(suspend_state_t state)
{
int ret = 0;
switch (state) {
case PM_SUSPEND_STANDBY:
case PM_SUSPEND_MEM:
ret = omap2_pm_suspend();
break;
default:
ret = -EINVAL;
}
return ret;
}
static void omap2_pm_finish(void)
{
enable_hlt();
}
static struct platform_suspend_ops omap_pm_ops = {
.prepare = omap2_pm_prepare,
.enter = omap2_pm_enter,
.finish = omap2_pm_finish,
.valid = suspend_valid_only_mem,
};
static int _pm_clkdm_enable_hwsup(struct clockdomain *clkdm)
{
omap2_clkdm_allow_idle(clkdm);
return 0;
}
static void __init prcm_setup_regs(void)
{
int i, num_mem_banks;
struct powerdomain *pwrdm;
/* Enable autoidle */
prm_write_mod_reg(OMAP24XX_AUTOIDLE, OCP_MOD,
OMAP2_PRCM_SYSCONFIG_OFFSET);
/* Set all domain wakeup dependencies */
prm_write_mod_reg(OMAP_EN_WKUP_MASK, MPU_MOD, PM_WKDEP);
prm_write_mod_reg(0, OMAP24XX_DSP_MOD, PM_WKDEP);
prm_write_mod_reg(0, GFX_MOD, PM_WKDEP);
prm_write_mod_reg(0, CORE_MOD, PM_WKDEP);
if (cpu_is_omap2430())
prm_write_mod_reg(0, OMAP2430_MDM_MOD, PM_WKDEP);
/*
* Set CORE powerdomain memory banks to retain their contents
* during RETENTION
*/
num_mem_banks = pwrdm_get_mem_bank_count(core_pwrdm);
for (i = 0; i < num_mem_banks; i++)
pwrdm_set_mem_retst(core_pwrdm, i, PWRDM_POWER_RET);
/* Set CORE powerdomain's next power state to RETENTION */
pwrdm_set_next_pwrst(core_pwrdm, PWRDM_POWER_RET);
/*
* Set MPU powerdomain's next power state to RETENTION;
* preserve logic state during retention
*/
pwrdm_set_logic_retst(mpu_pwrdm, PWRDM_POWER_RET);
pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);
/* Force-power down DSP, GFX powerdomains */
pwrdm = clkdm_get_pwrdm(dsp_clkdm);
pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);
omap2_clkdm_sleep(dsp_clkdm);
pwrdm = clkdm_get_pwrdm(gfx_clkdm);
pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);
omap2_clkdm_sleep(gfx_clkdm);
/* Enable clockdomain hardware-supervised control for all clkdms */
clkdm_for_each(_pm_clkdm_enable_hwsup);
/* Enable clock autoidle for all domains */
cm_write_mod_reg(OMAP24XX_AUTO_CAM |
OMAP24XX_AUTO_MAILBOXES |
OMAP24XX_AUTO_WDT4 |
OMAP2420_AUTO_WDT3 |
OMAP24XX_AUTO_MSPRO |
OMAP2420_AUTO_MMC |
OMAP24XX_AUTO_FAC |
OMAP2420_AUTO_EAC |
OMAP24XX_AUTO_HDQ |
OMAP24XX_AUTO_UART2 |
OMAP24XX_AUTO_UART1 |
OMAP24XX_AUTO_I2C2 |
OMAP24XX_AUTO_I2C1 |
OMAP24XX_AUTO_MCSPI2 |
OMAP24XX_AUTO_MCSPI1 |
OMAP24XX_AUTO_MCBSP2 |
OMAP24XX_AUTO_MCBSP1 |
OMAP24XX_AUTO_GPT12 |
OMAP24XX_AUTO_GPT11 |
OMAP24XX_AUTO_GPT10 |
OMAP24XX_AUTO_GPT9 |
OMAP24XX_AUTO_GPT8 |
OMAP24XX_AUTO_GPT7 |
OMAP24XX_AUTO_GPT6 |
OMAP24XX_AUTO_GPT5 |
OMAP24XX_AUTO_GPT4 |
OMAP24XX_AUTO_GPT3 |
OMAP24XX_AUTO_GPT2 |
OMAP2420_AUTO_VLYNQ |
OMAP24XX_AUTO_DSS,
CORE_MOD, CM_AUTOIDLE1);
cm_write_mod_reg(OMAP24XX_AUTO_UART3 |
OMAP24XX_AUTO_SSI |
OMAP24XX_AUTO_USB,
CORE_MOD, CM_AUTOIDLE2);
cm_write_mod_reg(OMAP24XX_AUTO_SDRC |
OMAP24XX_AUTO_GPMC |
OMAP24XX_AUTO_SDMA,
CORE_MOD, CM_AUTOIDLE3);
cm_write_mod_reg(OMAP24XX_AUTO_PKA |
OMAP24XX_AUTO_AES |
OMAP24XX_AUTO_RNG |
OMAP24XX_AUTO_SHA |
OMAP24XX_AUTO_DES,
CORE_MOD, OMAP24XX_CM_AUTOIDLE4);
cm_write_mod_reg(OMAP2420_AUTO_DSP_IPI, OMAP24XX_DSP_MOD, CM_AUTOIDLE);
/* Put DPLL and both APLLs into autoidle mode */
cm_write_mod_reg((0x03 << OMAP24XX_AUTO_DPLL_SHIFT) |
(0x03 << OMAP24XX_AUTO_96M_SHIFT) |
(0x03 << OMAP24XX_AUTO_54M_SHIFT),
PLL_MOD, CM_AUTOIDLE);
cm_write_mod_reg(OMAP24XX_AUTO_OMAPCTRL |
OMAP24XX_AUTO_WDT1 |
OMAP24XX_AUTO_MPU_WDT |
OMAP24XX_AUTO_GPIOS |
OMAP24XX_AUTO_32KSYNC |
OMAP24XX_AUTO_GPT1,
WKUP_MOD, CM_AUTOIDLE);
/* REVISIT: Configure number of 32 kHz clock cycles for sys_clk
* stabilisation */
prm_write_mod_reg(15 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
OMAP2_PRCM_CLKSSETUP_OFFSET);
/* Configure automatic voltage transition */
prm_write_mod_reg(2 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
OMAP2_PRCM_VOLTSETUP_OFFSET);
prm_write_mod_reg(OMAP24XX_AUTO_EXTVOLT |
(0x1 << OMAP24XX_SETOFF_LEVEL_SHIFT) |
OMAP24XX_MEMRETCTRL |
(0x1 << OMAP24XX_SETRET_LEVEL_SHIFT) |
(0x0 << OMAP24XX_VOLT_LEVEL_SHIFT),
OMAP24XX_GR_MOD, OMAP2_PRCM_VOLTCTRL_OFFSET);
/* Enable wake-up events */
prm_write_mod_reg(OMAP24XX_EN_GPIOS | OMAP24XX_EN_GPT1,
WKUP_MOD, PM_WKEN);
}
int __init omap2_pm_init(void)
{
u32 l;
if (!cpu_is_omap24xx())
return -ENODEV;
printk(KERN_INFO "Power Management for OMAP2 initializing\n");
l = prm_read_mod_reg(OCP_MOD, OMAP2_PRCM_REVISION_OFFSET);
printk(KERN_INFO "PRCM revision %d.%d\n", (l >> 4) & 0x0f, l & 0x0f);
/* Look up important powerdomains, clockdomains */
mpu_pwrdm = pwrdm_lookup("mpu_pwrdm");
if (!mpu_pwrdm)
pr_err("PM: mpu_pwrdm not found\n");
core_pwrdm = pwrdm_lookup("core_pwrdm");
if (!core_pwrdm)
pr_err("PM: core_pwrdm not found\n");
dsp_clkdm = clkdm_lookup("dsp_clkdm");
if (!dsp_clkdm)
pr_err("PM: mpu_clkdm not found\n");
gfx_clkdm = clkdm_lookup("gfx_clkdm");
if (!gfx_clkdm)
pr_err("PM: gfx_clkdm not found\n");
osc_ck = clk_get(NULL, "osc_ck");
if (IS_ERR(osc_ck)) {
printk(KERN_ERR "could not get osc_ck\n");
return -ENODEV;
}
if (cpu_is_omap242x()) {
emul_ck = clk_get(NULL, "emul_ck");
if (IS_ERR(emul_ck)) {
printk(KERN_ERR "could not get emul_ck\n");
clk_put(osc_ck);
return -ENODEV;
}
}
prcm_setup_regs();
/* Hack to prevent MPU retention when STI console is enabled. */
{
const struct omap_sti_console_config *sti;
sti = omap_get_config(OMAP_TAG_STI_CONSOLE,
struct omap_sti_console_config);
if (sti != NULL && sti->enable)
sti_console_enabled = 1;
}
/*
* We copy the assembler sleep/wakeup routines to SRAM.
* These routines need to be in SRAM as that's the only
* memory the MPU can see when it wakes up.
*/
if (cpu_is_omap24xx()) {
omap2_sram_idle = omap_sram_push(omap24xx_idle_loop_suspend,
omap24xx_idle_loop_suspend_sz);
omap2_sram_suspend = omap_sram_push(omap24xx_cpu_suspend,
omap24xx_cpu_suspend_sz);
}
suspend_set_ops(&omap_pm_ops);
pm_idle = omap2_pm_idle;
return 0;
}
late_initcall(omap2_pm_init);
/*
* OMAP3 Power Management Routines
*
* Copyright (C) 2006-2008 Nokia Corporation
* Tony Lindgren <tony@atomide.com>
* Jouni Hogander
*
* Copyright (C) 2005 Texas Instruments, Inc.
* Richard Woodruff <r-woodruff2@ti.com>
*
* Based on pm.c for omap1
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/pm.h>
#include <linux/suspend.h>
#include <linux/interrupt.h>
#include <linux/module.h>
#include <linux/list.h>
#include <linux/err.h>
#include <linux/gpio.h>
#include <mach/sram.h>
#include <mach/clockdomain.h>
#include <mach/powerdomain.h>
#include <mach/control.h>
#include "cm.h"
#include "cm-regbits-34xx.h"
#include "prm-regbits-34xx.h"
#include "prm.h"
#include "pm.h"
struct power_state {
struct powerdomain *pwrdm;
u32 next_state;
u32 saved_state;
struct list_head node;
};
static LIST_HEAD(pwrst_list);
static void (*_omap_sram_idle)(u32 *addr, int save_state);
static struct powerdomain *mpu_pwrdm;
/* PRCM Interrupt Handler for wakeups */
static irqreturn_t prcm_interrupt_handler (int irq, void *dev_id)
{
u32 wkst, irqstatus_mpu;
u32 fclk, iclk;
/* WKUP */
wkst = prm_read_mod_reg(WKUP_MOD, PM_WKST);
if (wkst) {
iclk = cm_read_mod_reg(WKUP_MOD, CM_ICLKEN);
fclk = cm_read_mod_reg(WKUP_MOD, CM_FCLKEN);
cm_set_mod_reg_bits(wkst, WKUP_MOD, CM_ICLKEN);
cm_set_mod_reg_bits(wkst, WKUP_MOD, CM_FCLKEN);
prm_write_mod_reg(wkst, WKUP_MOD, PM_WKST);
while (prm_read_mod_reg(WKUP_MOD, PM_WKST))
cpu_relax();
cm_write_mod_reg(iclk, WKUP_MOD, CM_ICLKEN);
cm_write_mod_reg(fclk, WKUP_MOD, CM_FCLKEN);
}
/* CORE */
wkst = prm_read_mod_reg(CORE_MOD, PM_WKST1);
if (wkst) {
iclk = cm_read_mod_reg(CORE_MOD, CM_ICLKEN1);
fclk = cm_read_mod_reg(CORE_MOD, CM_FCLKEN1);
cm_set_mod_reg_bits(wkst, CORE_MOD, CM_ICLKEN1);
cm_set_mod_reg_bits(wkst, CORE_MOD, CM_FCLKEN1);
prm_write_mod_reg(wkst, CORE_MOD, PM_WKST1);
while (prm_read_mod_reg(CORE_MOD, PM_WKST1))
cpu_relax();
cm_write_mod_reg(iclk, CORE_MOD, CM_ICLKEN1);
cm_write_mod_reg(fclk, CORE_MOD, CM_FCLKEN1);
}
wkst = prm_read_mod_reg(CORE_MOD, OMAP3430ES2_PM_WKST3);
if (wkst) {
iclk = cm_read_mod_reg(CORE_MOD, CM_ICLKEN3);
fclk = cm_read_mod_reg(CORE_MOD, OMAP3430ES2_CM_FCLKEN3);
cm_set_mod_reg_bits(wkst, CORE_MOD, CM_ICLKEN3);
cm_set_mod_reg_bits(wkst, CORE_MOD, OMAP3430ES2_CM_FCLKEN3);
prm_write_mod_reg(wkst, CORE_MOD, OMAP3430ES2_PM_WKST3);
while (prm_read_mod_reg(CORE_MOD, OMAP3430ES2_PM_WKST3))
cpu_relax();
cm_write_mod_reg(iclk, CORE_MOD, CM_ICLKEN3);
cm_write_mod_reg(fclk, CORE_MOD, OMAP3430ES2_CM_FCLKEN3);
}
/* PER */
wkst = prm_read_mod_reg(OMAP3430_PER_MOD, PM_WKST);
if (wkst) {
iclk = cm_read_mod_reg(OMAP3430_PER_MOD, CM_ICLKEN);
fclk = cm_read_mod_reg(OMAP3430_PER_MOD, CM_FCLKEN);
cm_set_mod_reg_bits(wkst, OMAP3430_PER_MOD, CM_ICLKEN);
cm_set_mod_reg_bits(wkst, OMAP3430_PER_MOD, CM_FCLKEN);
prm_write_mod_reg(wkst, OMAP3430_PER_MOD, PM_WKST);
while (prm_read_mod_reg(OMAP3430_PER_MOD, PM_WKST))
cpu_relax();
cm_write_mod_reg(iclk, OMAP3430_PER_MOD, CM_ICLKEN);
cm_write_mod_reg(fclk, OMAP3430_PER_MOD, CM_FCLKEN);
}
if (omap_rev() > OMAP3430_REV_ES1_0) {
/* USBHOST */
wkst = prm_read_mod_reg(OMAP3430ES2_USBHOST_MOD, PM_WKST);
if (wkst) {
iclk = cm_read_mod_reg(OMAP3430ES2_USBHOST_MOD,
CM_ICLKEN);
fclk = cm_read_mod_reg(OMAP3430ES2_USBHOST_MOD,
CM_FCLKEN);
cm_set_mod_reg_bits(wkst, OMAP3430ES2_USBHOST_MOD,
CM_ICLKEN);
cm_set_mod_reg_bits(wkst, OMAP3430ES2_USBHOST_MOD,
CM_FCLKEN);
prm_write_mod_reg(wkst, OMAP3430ES2_USBHOST_MOD,
PM_WKST);
while (prm_read_mod_reg(OMAP3430ES2_USBHOST_MOD,
PM_WKST))
cpu_relax();
cm_write_mod_reg(iclk, OMAP3430ES2_USBHOST_MOD,
CM_ICLKEN);
cm_write_mod_reg(fclk, OMAP3430ES2_USBHOST_MOD,
CM_FCLKEN);
}
}
irqstatus_mpu = prm_read_mod_reg(OCP_MOD,
OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
prm_write_mod_reg(irqstatus_mpu, OCP_MOD,
OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
while (prm_read_mod_reg(OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET))
cpu_relax();
return IRQ_HANDLED;
}
static void omap_sram_idle(void)
{
/* Variable to tell what needs to be saved and restored
* in omap_sram_idle*/
/* save_state = 0 => Nothing to save and restored */
/* save_state = 1 => Only L1 and logic lost */
/* save_state = 2 => Only L2 lost */
/* save_state = 3 => L1, L2 and logic lost */
int save_state = 0, mpu_next_state;
if (!_omap_sram_idle)
return;
mpu_next_state = pwrdm_read_next_pwrst(mpu_pwrdm);
switch (mpu_next_state) {
case PWRDM_POWER_RET:
/* No need to save context */
save_state = 0;
break;
default:
/* Invalid state */
printk(KERN_ERR "Invalid mpu state in sram_idle\n");
return;
}
omap2_gpio_prepare_for_retention();
_omap_sram_idle(NULL, save_state);
cpu_init();
omap2_gpio_resume_after_retention();
}
/*
* Check if functional clocks are enabled before entering
* sleep. This function could be behind CONFIG_PM_DEBUG
* when all drivers are configuring their sysconfig registers
* properly and using their clocks properly.
*/
static int omap3_fclks_active(void)
{
u32 fck_core1 = 0, fck_core3 = 0, fck_sgx = 0, fck_dss = 0,
fck_cam = 0, fck_per = 0, fck_usbhost = 0;
fck_core1 = cm_read_mod_reg(CORE_MOD,
CM_FCLKEN1);
if (omap_rev() > OMAP3430_REV_ES1_0) {
fck_core3 = cm_read_mod_reg(CORE_MOD,
OMAP3430ES2_CM_FCLKEN3);
fck_sgx = cm_read_mod_reg(OMAP3430ES2_SGX_MOD,
CM_FCLKEN);
fck_usbhost = cm_read_mod_reg(OMAP3430ES2_USBHOST_MOD,
CM_FCLKEN);
} else
fck_sgx = cm_read_mod_reg(GFX_MOD,
OMAP3430ES2_CM_FCLKEN3);
fck_dss = cm_read_mod_reg(OMAP3430_DSS_MOD,
CM_FCLKEN);
fck_cam = cm_read_mod_reg(OMAP3430_CAM_MOD,
CM_FCLKEN);
fck_per = cm_read_mod_reg(OMAP3430_PER_MOD,
CM_FCLKEN);
if (fck_core1 | fck_core3 | fck_sgx | fck_dss |
fck_cam | fck_per | fck_usbhost)
return 1;
return 0;
}
static int omap3_can_sleep(void)
{
if (omap3_fclks_active())
return 0;
return 1;
}
/* This sets pwrdm state (other than mpu & core. Currently only ON &
* RET are supported. Function is assuming that clkdm doesn't have
* hw_sup mode enabled. */
static int set_pwrdm_state(struct powerdomain *pwrdm, u32 state)
{
u32 cur_state;
int sleep_switch = 0;
int ret = 0;
if (pwrdm == NULL || IS_ERR(pwrdm))
return -EINVAL;
while (!(pwrdm->pwrsts & (1 << state))) {
if (state == PWRDM_POWER_OFF)
return ret;
state--;
}
cur_state = pwrdm_read_next_pwrst(pwrdm);
if (cur_state == state)
return ret;
if (pwrdm_read_pwrst(pwrdm) < PWRDM_POWER_ON) {
omap2_clkdm_wakeup(pwrdm->pwrdm_clkdms[0]);
sleep_switch = 1;
pwrdm_wait_transition(pwrdm);
}
ret = pwrdm_set_next_pwrst(pwrdm, state);
if (ret) {
printk(KERN_ERR "Unable to set state of powerdomain: %s\n",
pwrdm->name);
goto err;
}
if (sleep_switch) {
omap2_clkdm_allow_idle(pwrdm->pwrdm_clkdms[0]);
pwrdm_wait_transition(pwrdm);
}
err:
return ret;
}
static void omap3_pm_idle(void)
{
local_irq_disable();
local_fiq_disable();
if (!omap3_can_sleep())
goto out;
if (omap_irq_pending())
goto out;
omap_sram_idle();
out:
local_fiq_enable();
local_irq_enable();
}
static int omap3_pm_prepare(void)
{
disable_hlt();
return 0;
}
static int omap3_pm_suspend(void)
{
struct power_state *pwrst;
int state, ret = 0;
/* Read current next_pwrsts */
list_for_each_entry(pwrst, &pwrst_list, node)
pwrst->saved_state = pwrdm_read_next_pwrst(pwrst->pwrdm);
/* Set ones wanted by suspend */
list_for_each_entry(pwrst, &pwrst_list, node) {
if (set_pwrdm_state(pwrst->pwrdm, pwrst->next_state))
goto restore;
if (pwrdm_clear_all_prev_pwrst(pwrst->pwrdm))
goto restore;
}
omap_sram_idle();
restore:
/* Restore next_pwrsts */
list_for_each_entry(pwrst, &pwrst_list, node) {
set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state);
state = pwrdm_read_prev_pwrst(pwrst->pwrdm);
if (state > pwrst->next_state) {
printk(KERN_INFO "Powerdomain (%s) didn't enter "
"target state %d\n",
pwrst->pwrdm->name, pwrst->next_state);
ret = -1;
}
}
if (ret)
printk(KERN_ERR "Could not enter target state in pm_suspend\n");
else
printk(KERN_INFO "Successfully put all powerdomains "
"to target state\n");
return ret;
}
static int omap3_pm_enter(suspend_state_t state)
{
int ret = 0;
switch (state) {
case PM_SUSPEND_STANDBY:
case PM_SUSPEND_MEM:
ret = omap3_pm_suspend();
break;
default:
ret = -EINVAL;
}
return ret;
}
static void omap3_pm_finish(void)
{
enable_hlt();
}
static struct platform_suspend_ops omap_pm_ops = {
.prepare = omap3_pm_prepare,
.enter = omap3_pm_enter,
.finish = omap3_pm_finish,
.valid = suspend_valid_only_mem,
};
static void __init prcm_setup_regs(void)
{
/* reset modem */
prm_write_mod_reg(OMAP3430_RM_RSTCTRL_CORE_MODEM_SW_RSTPWRON |
OMAP3430_RM_RSTCTRL_CORE_MODEM_SW_RST,
CORE_MOD, RM_RSTCTRL);
prm_write_mod_reg(0, CORE_MOD, RM_RSTCTRL);
/* XXX Reset all wkdeps. This should be done when initializing
* powerdomains */
prm_write_mod_reg(0, OMAP3430_IVA2_MOD, PM_WKDEP);
prm_write_mod_reg(0, MPU_MOD, PM_WKDEP);
prm_write_mod_reg(0, OMAP3430_DSS_MOD, PM_WKDEP);
prm_write_mod_reg(0, OMAP3430_NEON_MOD, PM_WKDEP);
prm_write_mod_reg(0, OMAP3430_CAM_MOD, PM_WKDEP);
prm_write_mod_reg(0, OMAP3430_PER_MOD, PM_WKDEP);
if (omap_rev() > OMAP3430_REV_ES1_0) {
prm_write_mod_reg(0, OMAP3430ES2_SGX_MOD, PM_WKDEP);
prm_write_mod_reg(0, OMAP3430ES2_USBHOST_MOD, PM_WKDEP);
} else
prm_write_mod_reg(0, GFX_MOD, PM_WKDEP);
/*
* Enable interface clock autoidle for all modules.
* Note that in the long run this should be done by clockfw
*/
cm_write_mod_reg(
OMAP3430ES2_AUTO_MMC3 |
OMAP3430ES2_AUTO_ICR |
OMAP3430_AUTO_AES2 |
OMAP3430_AUTO_SHA12 |
OMAP3430_AUTO_DES2 |
OMAP3430_AUTO_MMC2 |
OMAP3430_AUTO_MMC1 |
OMAP3430_AUTO_MSPRO |
OMAP3430_AUTO_HDQ |
OMAP3430_AUTO_MCSPI4 |
OMAP3430_AUTO_MCSPI3 |
OMAP3430_AUTO_MCSPI2 |
OMAP3430_AUTO_MCSPI1 |
OMAP3430_AUTO_I2C3 |
OMAP3430_AUTO_I2C2 |
OMAP3430_AUTO_I2C1 |
OMAP3430_AUTO_UART2 |
OMAP3430_AUTO_UART1 |
OMAP3430_AUTO_GPT11 |
OMAP3430_AUTO_GPT10 |
OMAP3430_AUTO_MCBSP5 |
OMAP3430_AUTO_MCBSP1 |
OMAP3430ES1_AUTO_FAC | /* This is es1 only */
OMAP3430_AUTO_MAILBOXES |
OMAP3430_AUTO_OMAPCTRL |
OMAP3430ES1_AUTO_FSHOSTUSB |
OMAP3430_AUTO_HSOTGUSB |
OMAP3430ES1_AUTO_D2D | /* This is es1 only */
OMAP3430_AUTO_SSI,
CORE_MOD, CM_AUTOIDLE1);
cm_write_mod_reg(
OMAP3430_AUTO_PKA |
OMAP3430_AUTO_AES1 |
OMAP3430_AUTO_RNG |
OMAP3430_AUTO_SHA11 |
OMAP3430_AUTO_DES1,
CORE_MOD, CM_AUTOIDLE2);
if (omap_rev() > OMAP3430_REV_ES1_0) {
cm_write_mod_reg(
OMAP3430ES2_AUTO_USBTLL,
CORE_MOD, CM_AUTOIDLE3);
}
cm_write_mod_reg(
OMAP3430_AUTO_WDT2 |
OMAP3430_AUTO_WDT1 |
OMAP3430_AUTO_GPIO1 |
OMAP3430_AUTO_32KSYNC |
OMAP3430_AUTO_GPT12 |
OMAP3430_AUTO_GPT1 ,
WKUP_MOD, CM_AUTOIDLE);
cm_write_mod_reg(
OMAP3430_AUTO_DSS,
OMAP3430_DSS_MOD,
CM_AUTOIDLE);
cm_write_mod_reg(
OMAP3430_AUTO_CAM,
OMAP3430_CAM_MOD,
CM_AUTOIDLE);
cm_write_mod_reg(
OMAP3430_AUTO_GPIO6 |
OMAP3430_AUTO_GPIO5 |
OMAP3430_AUTO_GPIO4 |
OMAP3430_AUTO_GPIO3 |
OMAP3430_AUTO_GPIO2 |
OMAP3430_AUTO_WDT3 |
OMAP3430_AUTO_UART3 |
OMAP3430_AUTO_GPT9 |
OMAP3430_AUTO_GPT8 |
OMAP3430_AUTO_GPT7 |
OMAP3430_AUTO_GPT6 |
OMAP3430_AUTO_GPT5 |
OMAP3430_AUTO_GPT4 |
OMAP3430_AUTO_GPT3 |
OMAP3430_AUTO_GPT2 |
OMAP3430_AUTO_MCBSP4 |
OMAP3430_AUTO_MCBSP3 |
OMAP3430_AUTO_MCBSP2,
OMAP3430_PER_MOD,
CM_AUTOIDLE);
if (omap_rev() > OMAP3430_REV_ES1_0) {
cm_write_mod_reg(
OMAP3430ES2_AUTO_USBHOST,
OMAP3430ES2_USBHOST_MOD,
CM_AUTOIDLE);
}
/*
* Set all plls to autoidle. This is needed until autoidle is
* enabled by clockfw
*/
cm_write_mod_reg(1 << OMAP3430_AUTO_IVA2_DPLL_SHIFT,
OMAP3430_IVA2_MOD, CM_AUTOIDLE2);
cm_write_mod_reg(1 << OMAP3430_AUTO_MPU_DPLL_SHIFT,
MPU_MOD,
CM_AUTOIDLE2);
cm_write_mod_reg((1 << OMAP3430_AUTO_PERIPH_DPLL_SHIFT) |
(1 << OMAP3430_AUTO_CORE_DPLL_SHIFT),
PLL_MOD,
CM_AUTOIDLE);
cm_write_mod_reg(1 << OMAP3430ES2_AUTO_PERIPH2_DPLL_SHIFT,
PLL_MOD,
CM_AUTOIDLE2);
/*
* Enable control of expternal oscillator through
* sys_clkreq. In the long run clock framework should
* take care of this.
*/
prm_rmw_mod_reg_bits(OMAP_AUTOEXTCLKMODE_MASK,
1 << OMAP_AUTOEXTCLKMODE_SHIFT,
OMAP3430_GR_MOD,
OMAP3_PRM_CLKSRC_CTRL_OFFSET);
/* setup wakup source */
prm_write_mod_reg(OMAP3430_EN_IO | OMAP3430_EN_GPIO1 |
OMAP3430_EN_GPT1 | OMAP3430_EN_GPT12,
WKUP_MOD, PM_WKEN);
/* No need to write EN_IO, that is always enabled */
prm_write_mod_reg(OMAP3430_EN_GPIO1 | OMAP3430_EN_GPT1 |
OMAP3430_EN_GPT12,
WKUP_MOD, OMAP3430_PM_MPUGRPSEL);
/* For some reason IO doesn't generate wakeup event even if
* it is selected to mpu wakeup goup */
prm_write_mod_reg(OMAP3430_IO_EN | OMAP3430_WKUP_EN,
OCP_MOD, OMAP3_PRM_IRQENABLE_MPU_OFFSET);
}
static int __init pwrdms_setup(struct powerdomain *pwrdm)
{
struct power_state *pwrst;
if (!pwrdm->pwrsts)
return 0;
pwrst = kmalloc(sizeof(struct power_state), GFP_KERNEL);
if (!pwrst)
return -ENOMEM;
pwrst->pwrdm = pwrdm;
pwrst->next_state = PWRDM_POWER_RET;
list_add(&pwrst->node, &pwrst_list);
if (pwrdm_has_hdwr_sar(pwrdm))
pwrdm_enable_hdwr_sar(pwrdm);
return set_pwrdm_state(pwrst->pwrdm, pwrst->next_state);
}
/*
* Enable hw supervised mode for all clockdomains if it's
* supported. Initiate sleep transition for other clockdomains, if
* they are not used
*/
static int __init clkdms_setup(struct clockdomain *clkdm)
{
if (clkdm->flags & CLKDM_CAN_ENABLE_AUTO)
omap2_clkdm_allow_idle(clkdm);
else if (clkdm->flags & CLKDM_CAN_FORCE_SLEEP &&
atomic_read(&clkdm->usecount) == 0)
omap2_clkdm_sleep(clkdm);
return 0;
}
int __init omap3_pm_init(void)
{
struct power_state *pwrst, *tmp;
int ret;
if (!cpu_is_omap34xx())
return -ENODEV;
printk(KERN_ERR "Power Management for TI OMAP3.\n");
/* XXX prcm_setup_regs needs to be before enabling hw
* supervised mode for powerdomains */
prcm_setup_regs();
ret = request_irq(INT_34XX_PRCM_MPU_IRQ,
(irq_handler_t)prcm_interrupt_handler,
IRQF_DISABLED, "prcm", NULL);
if (ret) {
printk(KERN_ERR "request_irq failed to register for 0x%x\n",
INT_34XX_PRCM_MPU_IRQ);
goto err1;
}
ret = pwrdm_for_each(pwrdms_setup);
if (ret) {
printk(KERN_ERR "Failed to setup powerdomains\n");
goto err2;
}
(void) clkdm_for_each(clkdms_setup);
mpu_pwrdm = pwrdm_lookup("mpu_pwrdm");
if (mpu_pwrdm == NULL) {
printk(KERN_ERR "Failed to get mpu_pwrdm\n");
goto err2;
}
_omap_sram_idle = omap_sram_push(omap34xx_cpu_suspend,
omap34xx_cpu_suspend_sz);
suspend_set_ops(&omap_pm_ops);
pm_idle = omap3_pm_idle;
err1:
return ret;
err2:
free_irq(INT_34XX_PRCM_MPU_IRQ, NULL);
list_for_each_entry_safe(pwrst, tmp, &pwrst_list, node) {
list_del(&pwrst->node);
kfree(pwrst);
}
return ret;
}
late_initcall(omap3_pm_init);
......@@ -276,6 +276,8 @@
/* CM_FCLKEN_WKUP, CM_ICLKEN_WKUP, PM_WKEN_WKUP shared bits */
#define OMAP3430_EN_GPIO1 (1 << 3)
#define OMAP3430_EN_GPIO1_SHIFT 3
#define OMAP3430_EN_GPT12 (1 << 1)
#define OMAP3430_EN_GPT12_SHIFT 1
#define OMAP3430_EN_GPT1 (1 << 0)
#define OMAP3430_EN_GPT1_SHIFT 0
......
......@@ -60,9 +60,12 @@ struct omap_sdrc_params *omap2_sdrc_get_params(unsigned long r)
{
struct omap_sdrc_params *sp;
if (!sdrc_init_params)
return NULL;
sp = sdrc_init_params;
while (sp->rate != r)
while (sp->rate && sp->rate != r)
sp++;
if (!sp->rate)
......
......@@ -28,7 +28,6 @@
#include <linux/linkage.h>
#include <asm/assembler.h>
#include <mach/io.h>
#include <mach/pm.h>
#include <mach/omap24xx.h>
......
/*
* linux/arch/arm/mach-omap2/sleep.S
*
* (C) Copyright 2007
* Texas Instruments
* Karthik Dasu <karthik-dp@ti.com>
*
* (C) Copyright 2004
* Texas Instruments, <www.ti.com>
* Richard Woodruff <r-woodruff2@ti.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <linux/linkage.h>
#include <asm/assembler.h>
#include <mach/io.h>
#include <mach/control.h>
#include "prm.h"
#include "sdrc.h"
#define PM_PREPWSTST_CORE_V OMAP34XX_PRM_REGADDR(CORE_MOD, \
OMAP3430_PM_PREPWSTST)
#define PM_PREPWSTST_MPU_V OMAP34XX_PRM_REGADDR(MPU_MOD, \
OMAP3430_PM_PREPWSTST)
#define PM_PWSTCTRL_MPU_P OMAP34XX_PRM_REGADDR(MPU_MOD, PM_PWSTCTRL)
#define SCRATCHPAD_MEM_OFFS 0x310 /* Move this as correct place is
* available */
#define SCRATCHPAD_BASE_P OMAP343X_CTRL_REGADDR(\
OMAP343X_CONTROL_MEM_WKUP +\
SCRATCHPAD_MEM_OFFS)
#define SDRC_POWER_V OMAP34XX_SDRC_REGADDR(SDRC_POWER)
.text
/* Function call to get the restore pointer for resume from OFF */
ENTRY(get_restore_pointer)
stmfd sp!, {lr} @ save registers on stack
adr r0, restore
ldmfd sp!, {pc} @ restore regs and return
ENTRY(get_restore_pointer_sz)
.word . - get_restore_pointer_sz
/*
* Forces OMAP into idle state
*
* omap34xx_suspend() - This bit of code just executes the WFI
* for normal idles.
*
* Note: This code get's copied to internal SRAM at boot. When the OMAP
* wakes up it continues execution at the point it went to sleep.
*/
ENTRY(omap34xx_cpu_suspend)
stmfd sp!, {r0-r12, lr} @ save registers on stack
loop:
/*b loop*/ @Enable to debug by stepping through code
/* r0 contains restore pointer in sdram */
/* r1 contains information about saving context */
ldr r4, sdrc_power @ read the SDRC_POWER register
ldr r5, [r4] @ read the contents of SDRC_POWER
orr r5, r5, #0x40 @ enable self refresh on idle req
str r5, [r4] @ write back to SDRC_POWER register
cmp r1, #0x0
/* If context save is required, do that and execute wfi */
bne save_context_wfi
/* Data memory barrier and Data sync barrier */
mov r1, #0
mcr p15, 0, r1, c7, c10, 4
mcr p15, 0, r1, c7, c10, 5
wfi @ wait for interrupt
nop
nop
nop
nop
nop
nop
nop
nop
nop
nop
bl i_dll_wait
ldmfd sp!, {r0-r12, pc} @ restore regs and return
restore:
/* b restore*/ @ Enable to debug restore code
/* Check what was the reason for mpu reset and store the reason in r9*/
/* 1 - Only L1 and logic lost */
/* 2 - Only L2 lost - In this case, we wont be here */
/* 3 - Both L1 and L2 lost */
ldr r1, pm_pwstctrl_mpu
ldr r2, [r1]
and r2, r2, #0x3
cmp r2, #0x0 @ Check if target power state was OFF or RET
moveq r9, #0x3 @ MPU OFF => L1 and L2 lost
movne r9, #0x1 @ Only L1 and L2 lost => avoid L2 invalidation
bne logic_l1_restore
/* Execute smi to invalidate L2 cache */
mov r12, #0x1 @ set up to invalide L2
smi: .word 0xE1600070 @ Call SMI monitor (smieq)
logic_l1_restore:
mov r1, #0
/* Invalidate all instruction caches to PoU
* and flush branch target cache */
mcr p15, 0, r1, c7, c5, 0
ldr r4, scratchpad_base
ldr r3, [r4,#0xBC]
ldmia r3!, {r4-r6}
mov sp, r4
msr spsr_cxsf, r5
mov lr, r6
ldmia r3!, {r4-r9}
/* Coprocessor access Control Register */
mcr p15, 0, r4, c1, c0, 2
/* TTBR0 */
MCR p15, 0, r5, c2, c0, 0
/* TTBR1 */
MCR p15, 0, r6, c2, c0, 1
/* Translation table base control register */
MCR p15, 0, r7, c2, c0, 2
/*domain access Control Register */
MCR p15, 0, r8, c3, c0, 0
/* data fault status Register */
MCR p15, 0, r9, c5, c0, 0
ldmia r3!,{r4-r8}
/* instruction fault status Register */
MCR p15, 0, r4, c5, c0, 1
/*Data Auxiliary Fault Status Register */
MCR p15, 0, r5, c5, c1, 0
/*Instruction Auxiliary Fault Status Register*/
MCR p15, 0, r6, c5, c1, 1
/*Data Fault Address Register */
MCR p15, 0, r7, c6, c0, 0
/*Instruction Fault Address Register*/
MCR p15, 0, r8, c6, c0, 2
ldmia r3!,{r4-r7}
/* user r/w thread and process ID */
MCR p15, 0, r4, c13, c0, 2
/* user ro thread and process ID */
MCR p15, 0, r5, c13, c0, 3
/*Privileged only thread and process ID */
MCR p15, 0, r6, c13, c0, 4
/* cache size selection */
MCR p15, 2, r7, c0, c0, 0
ldmia r3!,{r4-r8}
/* Data TLB lockdown registers */
MCR p15, 0, r4, c10, c0, 0
/* Instruction TLB lockdown registers */
MCR p15, 0, r5, c10, c0, 1
/* Secure or Nonsecure Vector Base Address */
MCR p15, 0, r6, c12, c0, 0
/* FCSE PID */
MCR p15, 0, r7, c13, c0, 0
/* Context PID */
MCR p15, 0, r8, c13, c0, 1
ldmia r3!,{r4-r5}
/* primary memory remap register */
MCR p15, 0, r4, c10, c2, 0
/*normal memory remap register */
MCR p15, 0, r5, c10, c2, 1
/* Restore cpsr */
ldmia r3!,{r4} /*load CPSR from SDRAM*/
msr cpsr, r4 /*store cpsr */
/* Enabling MMU here */
mrc p15, 0, r7, c2, c0, 2 /* Read TTBRControl */
/* Extract N (0:2) bits and decide whether to use TTBR0 or TTBR1*/
and r7, #0x7
cmp r7, #0x0
beq usettbr0
ttbr_error:
/* More work needs to be done to support N[0:2] value other than 0
* So looping here so that the error can be detected
*/
b ttbr_error
usettbr0:
mrc p15, 0, r2, c2, c0, 0
ldr r5, ttbrbit_mask
and r2, r5
mov r4, pc
ldr r5, table_index_mask
and r4, r5 /* r4 = 31 to 20 bits of pc */
/* Extract the value to be written to table entry */
ldr r1, table_entry
add r1, r1, r4 /* r1 has value to be written to table entry*/
/* Getting the address of table entry to modify */
lsr r4, #18
add r2, r4 /* r2 has the location which needs to be modified */
/* Storing previous entry of location being modified */
ldr r5, scratchpad_base
ldr r4, [r2]
str r4, [r5, #0xC0]
/* Modify the table entry */
str r1, [r2]
/* Storing address of entry being modified
* - will be restored after enabling MMU */
ldr r5, scratchpad_base
str r2, [r5, #0xC4]
mov r0, #0
mcr p15, 0, r0, c7, c5, 4 @ Flush prefetch buffer
mcr p15, 0, r0, c7, c5, 6 @ Invalidate branch predictor array
mcr p15, 0, r0, c8, c5, 0 @ Invalidate instruction TLB
mcr p15, 0, r0, c8, c6, 0 @ Invalidate data TLB
/* Restore control register but dont enable caches here*/
/* Caches will be enabled after restoring MMU table entry */
ldmia r3!, {r4}
/* Store previous value of control register in scratchpad */
str r4, [r5, #0xC8]
ldr r2, cache_pred_disable_mask
and r4, r2
mcr p15, 0, r4, c1, c0, 0
ldmfd sp!, {r0-r12, pc} @ restore regs and return
save_context_wfi:
/*b save_context_wfi*/ @ enable to debug save code
mov r8, r0 /* Store SDRAM address in r8 */
/* Check what that target sleep state is:stored in r1*/
/* 1 - Only L1 and logic lost */
/* 2 - Only L2 lost */
/* 3 - Both L1 and L2 lost */
cmp r1, #0x2 /* Only L2 lost */
beq clean_l2
cmp r1, #0x1 /* L2 retained */
/* r9 stores whether to clean L2 or not*/
moveq r9, #0x0 /* Dont Clean L2 */
movne r9, #0x1 /* Clean L2 */
l1_logic_lost:
/* Store sp and spsr to SDRAM */
mov r4, sp
mrs r5, spsr
mov r6, lr
stmia r8!, {r4-r6}
/* Save all ARM registers */
/* Coprocessor access control register */
mrc p15, 0, r6, c1, c0, 2
stmia r8!, {r6}
/* TTBR0, TTBR1 and Translation table base control */
mrc p15, 0, r4, c2, c0, 0
mrc p15, 0, r5, c2, c0, 1
mrc p15, 0, r6, c2, c0, 2
stmia r8!, {r4-r6}
/* Domain access control register, data fault status register,
and instruction fault status register */
mrc p15, 0, r4, c3, c0, 0
mrc p15, 0, r5, c5, c0, 0
mrc p15, 0, r6, c5, c0, 1
stmia r8!, {r4-r6}
/* Data aux fault status register, instruction aux fault status,
datat fault address register and instruction fault address register*/
mrc p15, 0, r4, c5, c1, 0
mrc p15, 0, r5, c5, c1, 1
mrc p15, 0, r6, c6, c0, 0
mrc p15, 0, r7, c6, c0, 2
stmia r8!, {r4-r7}
/* user r/w thread and process ID, user r/o thread and process ID,
priv only thread and process ID, cache size selection */
mrc p15, 0, r4, c13, c0, 2
mrc p15, 0, r5, c13, c0, 3
mrc p15, 0, r6, c13, c0, 4
mrc p15, 2, r7, c0, c0, 0
stmia r8!, {r4-r7}
/* Data TLB lockdown, instruction TLB lockdown registers */
mrc p15, 0, r5, c10, c0, 0
mrc p15, 0, r6, c10, c0, 1
stmia r8!, {r5-r6}
/* Secure or non secure vector base address, FCSE PID, Context PID*/
mrc p15, 0, r4, c12, c0, 0
mrc p15, 0, r5, c13, c0, 0
mrc p15, 0, r6, c13, c0, 1
stmia r8!, {r4-r6}
/* Primary remap, normal remap registers */
mrc p15, 0, r4, c10, c2, 0
mrc p15, 0, r5, c10, c2, 1
stmia r8!,{r4-r5}
/* Store current cpsr*/
mrs r2, cpsr
stmia r8!, {r2}
mrc p15, 0, r4, c1, c0, 0
/* save control register */
stmia r8!, {r4}
clean_caches:
/* Clean Data or unified cache to POU*/
/* How to invalidate only L1 cache???? - #FIX_ME# */
/* mcr p15, 0, r11, c7, c11, 1 */
cmp r9, #1 /* Check whether L2 inval is required or not*/
bne skip_l2_inval
clean_l2:
/* read clidr */
mrc p15, 1, r0, c0, c0, 1
/* extract loc from clidr */
ands r3, r0, #0x7000000
/* left align loc bit field */
mov r3, r3, lsr #23
/* if loc is 0, then no need to clean */
beq finished
/* start clean at cache level 0 */
mov r10, #0
loop1:
/* work out 3x current cache level */
add r2, r10, r10, lsr #1
/* extract cache type bits from clidr*/
mov r1, r0, lsr r2
/* mask of the bits for current cache only */
and r1, r1, #7
/* see what cache we have at this level */
cmp r1, #2
/* skip if no cache, or just i-cache */
blt skip
/* select current cache level in cssr */
mcr p15, 2, r10, c0, c0, 0
/* isb to sych the new cssr&csidr */
isb
/* read the new csidr */
mrc p15, 1, r1, c0, c0, 0
/* extract the length of the cache lines */
and r2, r1, #7
/* add 4 (line length offset) */
add r2, r2, #4
ldr r4, assoc_mask
/* find maximum number on the way size */
ands r4, r4, r1, lsr #3
/* find bit position of way size increment */
clz r5, r4
ldr r7, numset_mask
/* extract max number of the index size*/
ands r7, r7, r1, lsr #13
loop2:
mov r9, r4
/* create working copy of max way size*/
loop3:
/* factor way and cache number into r11 */
orr r11, r10, r9, lsl r5
/* factor index number into r11 */
orr r11, r11, r7, lsl r2
/*clean & invalidate by set/way */
mcr p15, 0, r11, c7, c10, 2
/* decrement the way*/
subs r9, r9, #1
bge loop3
/*decrement the index */
subs r7, r7, #1
bge loop2
skip:
add r10, r10, #2
/* increment cache number */
cmp r3, r10
bgt loop1
finished:
/*swith back to cache level 0 */
mov r10, #0
/* select current cache level in cssr */
mcr p15, 2, r10, c0, c0, 0
isb
skip_l2_inval:
/* Data memory barrier and Data sync barrier */
mov r1, #0
mcr p15, 0, r1, c7, c10, 4
mcr p15, 0, r1, c7, c10, 5
wfi @ wait for interrupt
nop
nop
nop
nop
nop
nop
nop
nop
nop
nop
bl i_dll_wait
/* restore regs and return */
ldmfd sp!, {r0-r12, pc}
i_dll_wait:
ldr r4, clk_stabilize_delay
i_dll_delay:
subs r4, r4, #0x1
bne i_dll_delay
ldr r4, sdrc_power
ldr r5, [r4]
bic r5, r5, #0x40
str r5, [r4]
bx lr
pm_prepwstst_core:
.word PM_PREPWSTST_CORE_V
pm_prepwstst_mpu:
.word PM_PREPWSTST_MPU_V
pm_pwstctrl_mpu:
.word PM_PWSTCTRL_MPU_P
scratchpad_base:
.word SCRATCHPAD_BASE_P
sdrc_power:
.word SDRC_POWER_V
context_mem:
.word 0x803E3E14
clk_stabilize_delay:
.word 0x000001FF
assoc_mask:
.word 0x3ff
numset_mask:
.word 0x7fff
ttbrbit_mask:
.word 0xFFFFC000
table_index_mask:
.word 0xFFF00000
table_entry:
.word 0x00000C02
cache_pred_disable_mask:
.word 0xFFFFE7FB
ENTRY(omap34xx_cpu_suspend_sz)
.word . - omap34xx_cpu_suspend
......@@ -28,7 +28,6 @@
#include <mach/hardware.h>
#include <mach/irqs.h>
#include <mach/pm.h>
#include <mach/mux.h>
#include <mach/usb.h>
......
......@@ -171,7 +171,7 @@ endchoice
config OMAP_SERIAL_WAKE
bool "Enable wake-up events for serial ports"
depends on OMAP_MUX
depends on ARCH_OMAP1 && OMAP_MUX
default y
help
Select this option if you want to have your system wake up
......
......@@ -11,7 +11,6 @@
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/pm.h>
#include <linux/console.h>
#include <linux/serial.h>
#include <linux/tty.h>
......
......@@ -39,7 +39,6 @@
#include <mach/gpmc.h>
#include <mach/onenand.h>
#include <mach/gpio.h>
#include <mach/pm.h>
#include <mach/dma.h>
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment