Merge tag 'at91-cleanup' into at91-4.1-multiplatform

First batch of cleanup for 4.1:
- little phy fixup that is not needed anymore
- hudge cleanup of the PM code:
  - removal of "use slow clock" option => always use this for suspend to RAM
  - quicker suspend as the asm function is copied only once to SRAM
  - use of the same asm function for "standby" and "mem" types of suspend
    actions
  - adaptation to the ARMv7 processors

arch/arm/mach-at91/Kconfig

@@ -24,7 +24,7 @@ config SOC_SAMA5
 	select GENERIC_CLOCKEVENTS
 	select MEMORY
 	select ATMEL_SDRAMC
-	select PHYLIB if NETDEVICES
+	select SRAM if PM
 
 menu "Atmel AT91 System-on-Chip"
 
@@ -81,6 +81,7 @@ config SOC_AT91RM9200
 	select CPU_ARM920T
 	select GENERIC_CLOCKEVENTS
 	select HAVE_AT91_USB_CLK
+	select SRAM if PM
 
 config SOC_AT91SAM9
 	bool "AT91SAM9"
@@ -94,6 +95,7 @@ config SOC_AT91SAM9
 	select HAVE_AT91_UTMI
 	select HAVE_FB_ATMEL
 	select MEMORY
+	select SRAM if PM
 	help
 	  Select this if you are using one of those Atmel SoC:
 	    AT91SAM9260
@@ -116,20 +118,6 @@ endif # SOC_SAM_V4_V5
 
 comment "AT91 Feature Selections"
 
-config AT91_SLOW_CLOCK
-	bool "Suspend-to-RAM disables main oscillator"
-	select SRAM
-	depends on SUSPEND
-	help
-	  Select this if you want Suspend-to-RAM to save the most power
-	  possible (without powering off the CPU) by disabling the PLLs
-	  and main oscillator so that only the 32 KiHz clock is available.
-
-	  When only that slow-clock is available, some peripherals lose
-	  functionality.  Many can't issue wakeup events unless faster
-	  clocks are available.  Some lose their operating state and
-	  need to be completely re-initialized.
-
 config AT91_TIMER_HZ
        int "Kernel HZ (jiffies per second)"
        range 32 1024

arch/arm/mach-at91/Makefile

@@ -13,7 +13,7 @@ obj-$(CONFIG_SOC_SAMA5)		+= sama5.o
 
 # Power Management
 obj-$(CONFIG_PM)		+= pm.o
-obj-$(CONFIG_AT91_SLOW_CLOCK)	+= pm_slowclock.o
+obj-$(CONFIG_PM)		+= pm_suspend.o
 
 ifeq ($(CONFIG_PM_DEBUG),y)
 CFLAGS_pm.o += -DDEBUG

arch/arm/mach-at91/pm.c

@@ -29,6 +29,8 @@
 #include <linux/atomic.h>
 #include <asm/mach/time.h>
 #include <asm/mach/irq.h>
+#include <asm/fncpy.h>
+#include <asm/cacheflush.h>
 
 #include <mach/cpu.h>
 #include <mach/hardware.h>
@@ -41,7 +43,6 @@ static struct {
 	int memctrl;
 } at91_pm_data;
 
-static void (*at91_pm_standby)(void);
 void __iomem *at91_ramc_base[2];
 
 static int at91_pm_valid_state(suspend_state_t state)
@@ -119,15 +120,28 @@ int at91_suspend_entering_slow_clock(void)
 }
 EXPORT_SYMBOL(at91_suspend_entering_slow_clock);
 
-
-static void (*slow_clock)(void __iomem *pmc, void __iomem *ramc0,
+static void (*at91_suspend_sram_fn)(void __iomem *pmc, void __iomem *ramc0,
 			  void __iomem *ramc1, int memctrl);
 
-#ifdef CONFIG_AT91_SLOW_CLOCK
-extern void at91_slow_clock(void __iomem *pmc, void __iomem *ramc0,
+extern void at91_pm_suspend_in_sram(void __iomem *pmc, void __iomem *ramc0,
 			    void __iomem *ramc1, int memctrl);
-extern u32 at91_slow_clock_sz;
-#endif
+extern u32 at91_pm_suspend_in_sram_sz;
+
+static void at91_pm_suspend(suspend_state_t state)
+{
+	unsigned int pm_data = at91_pm_data.memctrl;
+
+	pm_data |= (state == PM_SUSPEND_MEM) ?
+				AT91_PM_MODE(AT91_PM_SLOW_CLOCK) : 0;
+
+	flush_cache_all();
+	outer_disable();
+
+	at91_suspend_sram_fn(at91_pmc_base, at91_ramc_base[0],
+				at91_ramc_base[1], pm_data);
+
+	outer_resume();
+}
 
 static int at91_pm_enter(suspend_state_t state)
 {
@@ -136,8 +150,8 @@ static int at91_pm_enter(suspend_state_t state)
 	switch (state) {
 	/*
 	 * Suspend-to-RAM is like STANDBY plus slow clock mode, so
-		 * drivers must suspend more deeply:  only the master clock
-		 * controller may be using the main oscillator.
+	 * drivers must suspend more deeply, the master clock switches
+	 * to the clk32k and turns off the main oscillator
 	 */
 	case PM_SUSPEND_MEM:
 		/*
@@ -146,23 +160,9 @@ static int at91_pm_enter(suspend_state_t state)
 		if (!at91_pm_verify_clocks())
 			goto error;
 
-			/*
-			 * Enter slow clock mode by switching over to clk32k and
-			 * turning off the main oscillator; reverse on wakeup.
-			 */
-			if (slow_clock) {
-#ifdef CONFIG_AT91_SLOW_CLOCK
-				/* copy slow_clock handler to SRAM, and call it */
-				memcpy(slow_clock, at91_slow_clock, at91_slow_clock_sz);
-#endif
-				slow_clock(at91_pmc_base, at91_ramc_base[0],
-					   at91_ramc_base[1],
-					   at91_pm_data.memctrl);
+		at91_pm_suspend(state);
+
 		break;
-			} else {
-				pr_info("AT91: PM - no slow clock mode enabled ...\n");
-				/* FALLTHROUGH leaving master clock alone */
-			}
 
 	/*
 	 * STANDBY mode has *all* drivers suspended; ignores irqs not
@@ -171,15 +171,7 @@ static int at91_pm_enter(suspend_state_t state)
 	 * nothing fancy done with main or cpu clocks.
 	 */
 	case PM_SUSPEND_STANDBY:
-			/*
-			 * NOTE: the Wait-for-Interrupt instruction needs to be
-			 * in icache so no SDRAM accesses are needed until the
-			 * wakeup IRQ occurs and self-refresh is terminated.
-			 * For ARM 926 based chips, this requirement is weaker
-			 * as at91sam9 can access a RAM in self-refresh mode.
-			 */
-			if (at91_pm_standby)
-				at91_pm_standby();
+		at91_pm_suspend(state);
 		break;
 
 	case PM_SUSPEND_ON:
@@ -218,12 +210,10 @@ static struct platform_device at91_cpuidle_device = {
 	.name = "cpuidle-at91",
 };
 
-void at91_pm_set_standby(void (*at91_standby)(void))
+static void at91_pm_set_standby(void (*at91_standby)(void))
 {
-	if (at91_standby) {
+	if (at91_standby)
 		at91_cpuidle_device.dev.platform_data = at91_standby;
-		at91_pm_standby = at91_standby;
-	}
 }
 
 static const struct of_device_id ramc_ids[] __initconst = {
@@ -263,7 +253,6 @@ static __init void at91_dt_ramc(void)
 	at91_pm_set_standby(standby);
 }
 
-#ifdef CONFIG_AT91_SLOW_CLOCK
 static void __init at91_pm_sram_init(void)
 {
 	struct gen_pool *sram_pool;
@@ -291,30 +280,36 @@ static void __init at91_pm_sram_init(void)
 		return;
 	}
 
-	sram_base = gen_pool_alloc(sram_pool, at91_slow_clock_sz);
+	sram_base = gen_pool_alloc(sram_pool, at91_pm_suspend_in_sram_sz);
 	if (!sram_base) {
-		pr_warn("%s: unable to alloc ocram!\n", __func__);
+		pr_warn("%s: unable to alloc sram!\n", __func__);
 		return;
 	}
 
 	sram_pbase = gen_pool_virt_to_phys(sram_pool, sram_base);
-	slow_clock = __arm_ioremap_exec(sram_pbase, at91_slow_clock_sz, false);
-}
-#endif
+	at91_suspend_sram_fn = __arm_ioremap_exec(sram_pbase,
+					at91_pm_suspend_in_sram_sz, false);
+	if (!at91_suspend_sram_fn) {
+		pr_warn("SRAM: Could not map\n");
+		return;
+	}
 
+	/* Copy the pm suspend handler to SRAM */
+	at91_suspend_sram_fn = fncpy(at91_suspend_sram_fn,
+			&at91_pm_suspend_in_sram, at91_pm_suspend_in_sram_sz);
+}
 
 static void __init at91_pm_init(void)
 {
-#ifdef CONFIG_AT91_SLOW_CLOCK
 	at91_pm_sram_init();
-#endif
-
-	pr_info("AT91: Power Management%s\n", (slow_clock ? " (with slow clock mode)" : ""));
 
 	if (at91_cpuidle_device.dev.platform_data)
 		platform_device_register(&at91_cpuidle_device);
 
+	if (at91_suspend_sram_fn)
 		suspend_set_ops(&at91_pm_ops);
+	else
+		pr_info("AT91: PM not supported, due to no SRAM allocated\n");
 }
 
 void __init at91rm9200_pm_init(void)

arch/arm/mach-at91/pm.h

@@ -15,11 +15,13 @@
 
 #include <mach/at91_ramc.h>
 
-#ifdef CONFIG_PM
-extern void at91_pm_set_standby(void (*at91_standby)(void));
-#else
-static inline void at91_pm_set_standby(void (*at91_standby)(void)) { }
-#endif
+#define	AT91_PM_MEMTYPE_MASK	0x0f
+
+#define	AT91_PM_MODE_OFFSET	4
+#define	AT91_PM_MODE_MASK	0x01
+#define	AT91_PM_MODE(x)		(((x) & AT91_PM_MODE_MASK) << AT91_PM_MODE_OFFSET)
+
+#define	AT91_PM_SLOW_CLOCK	0x01
 
 /*
  * The AT91RM9200 goes into self-refresh mode with this command, and will
@@ -31,6 +33,7 @@ static inline void at91_pm_set_standby(void (*at91_standby)(void)) { }
  * still in self-refresh is "not recommended", but seems to work.
  */
 
+#ifndef __ASSEMBLY__
 static inline void at91rm9200_standby(void)
 {
 	u32 lpr = at91_ramc_read(0, AT91RM9200_SDRAMC_LPR);
@@ -112,3 +115,4 @@ static inline void at91sam9_sdram_standby(void)
 }
 
 #endif
+#endif

arch/arm/mach-at91/sama5.c

@@ -11,13 +11,10 @@
 #include <linux/init.h>
 #include <linux/module.h>
 #include <linux/gpio.h>
-#include <linux/micrel_phy.h>
 #include <linux/of.h>
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
-#include <linux/phy.h>
 #include <linux/clk-provider.h>
-#include <linux/phy.h>
 
 #include <mach/hardware.h>
 
@@ -29,25 +26,8 @@
 
 #include "generic.h"
 
-static int ksz8081_phy_fixup(struct phy_device *phy)
-{
-	int value;
-
-	value = phy_read(phy, 0x16);
-	value &= ~0x20;
-	phy_write(phy, 0x16, value);
-
-	return 0;
-}
-
 static void __init sama5_dt_device_init(void)
 {
-	if (of_machine_is_compatible("atmel,sama5d4ek") &&
-	   IS_ENABLED(CONFIG_PHYLIB)) {
-		phy_register_fixup_for_id("fc028000.etherne:00",
-						ksz8081_phy_fixup);
-	}
-
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 	at91sam9x5_pm_init();
 }