[ARM PATCH] 2007/1: OMAP update 3/6: Arch files

Patch from Tony Lindgren

This patch syncs the mainline kernel with the linux-omap tree.
The highlights of the patch are:
- DMA fixes from Samuel Ortiz
- USB low level configuration from David Brownell
- H3 support from Nishant Kamat
- TPS65010 power management interface from Dirk Behme

arch/arm/mach-omap/Makefile

@@ -3,25 +3,29 @@
 #
 
 # Common support
-obj-y := common.o irq.o dma.o clocks.o mux.o bus.o gpio.o time.o
+obj-y := common.o time.o irq.o dma.o clocks.o mux.o gpio.o mcbsp.o
 obj-m :=
 obj-n :=
 obj-  :=
 led-y := leds.o
 
 # Specific board support
+obj-$(CONFIG_MACH_OMAP_H2) += board-h2.o
 obj-$(CONFIG_MACH_OMAP_INNOVATOR) += board-innovator.o
 obj-$(CONFIG_MACH_OMAP_GENERIC) += board-generic.o
 obj-$(CONFIG_MACH_OMAP_PERSEUS2) += board-perseus2.o
 obj-$(CONFIG_MACH_OMAP_OSK) += board-osk.o
+obj-$(CONFIG_MACH_OMAP_H3) += board-h3.o
 
-# OCPI interconnect support for 1610 and 5912
+# OCPI interconnect support for 1710, 1610 and 5912
+obj-$(CONFIG_ARCH_OMAP1710) += ocpi.o
 obj-$(CONFIG_ARCH_OMAP1610) += ocpi.o
 obj-$(CONFIG_ARCH_OMAP5912) += ocpi.o
 
 # LEDs support
+led-$(CONFIG_MACH_OMAP_H2) += leds-h2p2-debug.o
 led-$(CONFIG_MACH_OMAP_INNOVATOR) += leds-innovator.o
-led-$(CONFIG_MACH_OMAP_PERSEUS2) += leds-perseus2.o
+led-$(CONFIG_MACH_OMAP_PERSEUS2) += leds-h2p2-debug.o
 obj-$(CONFIG_LEDS) += $(led-y)
 
 # Power Management

arch/arm/mach-omap/board-generic.c

@@ -25,9 +25,13 @@
 #include <asm/arch/clocks.h>
 #include <asm/arch/gpio.h>
 #include <asm/arch/mux.h>
+#include <asm/arch/usb.h>
+#include <asm/arch/board.h>
 
 #include "common.h"
 
+extern void __init omap_init_time(void);
+
 static void __init omap_generic_init_irq(void)
 {
 	omap_init_irq();
@@ -36,17 +40,49 @@ static void __init omap_generic_init_irq(void)
 /*
  * Muxes the serial ports on
  */
+#ifdef CONFIG_ARCH_OMAP1510
 static void __init omap_early_serial_init(void)
 {
+#ifdef CONFIG_OMAP_LL_DEBUG_UART1
 	omap_cfg_reg(UART1_TX);
 	omap_cfg_reg(UART1_RTS);
+#endif
 
+#ifdef CONFIG_OMAP_LL_DEBUG_UART2
 	omap_cfg_reg(UART2_TX);
 	omap_cfg_reg(UART2_RTS);
+#endif
 
+#ifdef CONFIG_OMAP_LL_DEBUG_UART1
 	omap_cfg_reg(UART3_TX);
 	omap_cfg_reg(UART3_RX);
+#endif
 }
+#endif
+
+/* assume no Mini-AB port */
+
+#ifdef CONFIG_ARCH_OMAP1510
+static struct omap_usb_config generic1510_usb_config __initdata = {
+	.register_host	= 1,
+	.register_dev	= 1,
+	.hmc_mode	= 16,
+	.pins[0]	= 3,
+};
+#endif
+
+#ifdef CONFIG_ARCH_OMAP1610
+static struct omap_usb_config generic1610_usb_config __initdata = {
+	.register_host	= 1,
+	.register_dev	= 1,
+	.hmc_mode	= 16,
+	.pins[0]	= 6,
+};
+#endif
+
+static struct omap_board_config_kernel generic_config[] = {
+	{ OMAP_TAG_USB,           NULL },
+};
 
 static void __init omap_generic_init(void)
 {
@@ -55,9 +91,19 @@ static void __init omap_generic_init(void)
 	 * You have to mux them off in device drivers later on
 	 * if not needed.
 	 */
+#ifdef CONFIG_ARCH_OMAP1510
 	if (cpu_is_omap1510()) {
 		omap_early_serial_init();
+		generic_config[0].data = &generic1510_usb_config;
 	}
+#endif
+#ifdef CONFIG_ARCH_OMAP1610
+	if (!cpu_is_omap1510()) {
+		generic_config[0].data = &generic1610_usb_config;
+	}
+#endif
+	omap_board_config = generic_config;
+	omap_board_config_size = ARRAY_SIZE(generic_config);
 }
 
 static void __init omap_generic_map_io(void)
@@ -65,18 +111,12 @@ static void __init omap_generic_map_io(void)
 	omap_map_io();
 }
 
-static void __init omap_generic_init_time(void)
-{
-	omap_init_time();
-}
-
-MACHINE_START(OMAP_GENERIC, "Generic OMAP-1510/1610/1710")
+MACHINE_START(OMAP_GENERIC, "Generic OMAP1510/1610/1710")
 	MAINTAINER("Tony Lindgren <tony@atomide.com>")
 	BOOT_MEM(0x10000000, 0xfff00000, 0xfef00000)
 	BOOT_PARAMS(0x10000100)
 	MAPIO(omap_generic_map_io)
 	INITIRQ(omap_generic_init_irq)
 	INIT_MACHINE(omap_generic_init)
-	INITTIME(omap_generic_init_time)
+	INITTIME(omap_init_time)
 MACHINE_END
-

arch/arm/mach-omap/board-innovator.c

@@ -29,9 +29,12 @@
 #include <asm/arch/clocks.h>
 #include <asm/arch/gpio.h>
 #include <asm/arch/fpga.h>
+#include <asm/arch/usb.h>
 
 #include "common.h"
 
+extern void __init omap_init_time(void);
+
 #ifdef CONFIG_ARCH_OMAP1510
 
 extern int omap_gpio_init(void);
@@ -49,8 +52,8 @@ static struct resource innovator1510_smc91x_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start	= INT_ETHER,
-		.end	= INT_ETHER,
+		.start	= OMAP1510_INT_ETHER,
+		.end	= OMAP1510_INT_ETHER,
 		.flags	= IORESOURCE_IRQ,
 	},
 };
@@ -108,11 +111,43 @@ void innovator_init_irq(void)
 #ifdef CONFIG_ARCH_OMAP1510
 	if (cpu_is_omap1510()) {
 		omap_gpio_init();
-		fpga_init_irq();
+		omap1510_fpga_init_irq();
 	}
 #endif
 }
 
+#ifdef CONFIG_ARCH_OMAP1510
+static struct omap_usb_config innovator1510_usb_config __initdata = {
+	/* has usb host and device, but no Mini-AB port */
+	.register_host	= 1,
+	.register_dev	= 1,
+	/* Assume bad Innovator wiring; Use internal host only with custom cable */
+	.hmc_mode	= 16,
+	.pins[0]	= 2,
+};
+#endif
+
+#ifdef CONFIG_ARCH_OMAP1610
+static struct omap_usb_config h2_usb_config __initdata = {
+	/* usb1 has a Mini-AB port and external isp1301 transceiver */
+	.otg		= 2,
+
+#ifdef	CONFIG_USB_GADGET_OMAP
+	.hmc_mode	= 19,	// 0:host(off) 1:dev|otg 2:disabled
+	// .hmc_mode	= 21,	// 0:host(off) 1:dev(loopback) 2:host(loopback)
+#elif	defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+	/* NONSTANDARD CABLE NEEDED (B-to-Mini-B) */
+	.hmc_mode	= 20,	// 1:dev|otg(off) 1:host 2:disabled
+#endif
+
+	.pins[1]	= 3,
+};
+#endif
+
+static struct omap_board_config_kernel innovator_config[] = {
+	{ OMAP_TAG_USB,         NULL },
+};
+
 static void __init innovator_init(void)
 {
 #ifdef CONFIG_ARCH_OMAP1510
@@ -121,10 +156,21 @@ static void __init innovator_init(void)
 	}
 #endif
 #ifdef CONFIG_ARCH_OMAP1610
-	if (cpu_is_omap1610()) {
+	if (!cpu_is_omap1510()) {
 		platform_add_devices(innovator1610_devices, ARRAY_SIZE(innovator1610_devices));
 	}
 #endif
+
+#ifdef CONFIG_ARCH_OMAP1510
+	if (cpu_is_omap1510())
+		innovator_config[0].data = &innovator1510_usb_config;
+#endif
+#ifdef CONFIG_ARCH_OMAP1610
+	if (cpu_is_omap1610())
+		innovator_config[0].data = &h2_usb_config;
+#endif
+	omap_board_config = innovator_config;
+	omap_board_config_size = ARRAY_SIZE(innovator_config);
 }
 
 static void __init innovator_map_io(void)
@@ -144,7 +190,7 @@ static void __init innovator_map_io(void)
 	}
 #endif
 #ifdef CONFIG_ARCH_OMAP1610
-	if (cpu_is_omap1610()) {
+	if (!cpu_is_omap1510()) {
 		iotable_init(innovator1610_io_desc, ARRAY_SIZE(innovator1610_io_desc));
 	}
 #endif
@@ -156,6 +202,6 @@ MACHINE_START(OMAP_INNOVATOR, "TI-Innovator")
 	BOOT_PARAMS(0x10000100)
 	MAPIO(innovator_map_io)
 	INITIRQ(innovator_init_irq)
-	INITTIME(omap_init_time)
 	INIT_MACHINE(innovator_init)
+	INITTIME(omap_init_time)
 MACHINE_END

arch/arm/mach-omap/board-osk.c

@@ -41,6 +41,8 @@
 
 #include "common.h"
 
+extern void __init omap_init_time(void);
+
 static struct map_desc osk5912_io_desc[] __initdata = {
 { OMAP_OSK_ETHR_BASE, OMAP_OSK_ETHR_START, OMAP_OSK_ETHR_SIZE,MT_DEVICE },
 { OMAP_OSK_NOR_FLASH_BASE, OMAP_OSK_NOR_FLASH_START, OMAP_OSK_NOR_FLASH_SIZE,
@@ -94,6 +96,6 @@ MACHINE_START(OMAP_OSK, "TI-OSK")
 	BOOT_PARAMS(0x10000100)
 	MAPIO(osk_map_io)
 	INITIRQ(osk_init_irq)
-	INITTIME(omap_init_time)
 	INIT_MACHINE(osk_init)
+	INITTIME(omap_init_time)
 MACHINE_END

arch/arm/mach-omap/board-perseus2.c

@@ -23,9 +23,12 @@
 #include <asm/arch/clocks.h>
 #include <asm/arch/gpio.h>
 #include <asm/arch/mux.h>
+#include <asm/arch/fpga.h>
 
 #include "common.h"
 
+extern void __init omap_init_time(void);
+
 void omap_perseus2_init_irq(void)
 {
 	omap_init_irq();
@@ -33,14 +36,14 @@ void omap_perseus2_init_irq(void)
 
 static struct resource smc91x_resources[] = {
 	[0] = {
-		.start	= OMAP730_FPGA_ETHR_START,	/* Physical */
-		.end	= OMAP730_FPGA_ETHR_START + SZ_4K,
+		.start	= H2P2_DBG_FPGA_ETHR_START,	/* Physical */
+		.end	= H2P2_DBG_FPGA_ETHR_START + SZ_4K,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start	= 0,
+		.start	= INT_730_MPU_EXT_NIRQ,
 		.end	= 0,
-		.flags	= INT_ETHER,
+		.flags	= IORESOURCE_IRQ,
 	},
 };
 
@@ -62,7 +65,7 @@ static void __init omap_perseus2_init(void)
 
 /* Only FPGA needs to be mapped here. All others are done with ioremap */
 static struct map_desc omap_perseus2_io_desc[] __initdata = {
-	{OMAP730_FPGA_BASE, OMAP730_FPGA_START, OMAP730_FPGA_SIZE,
+	{H2P2_DBG_FPGA_BASE, H2P2_DBG_FPGA_START, H2P2_DBG_FPGA_SIZE,
 	 MT_DEVICE},
 };
 
@@ -111,6 +114,6 @@ MACHINE_START(OMAP_PERSEUS2, "OMAP730 Perseus2")
 	BOOT_PARAMS(0x10000100)
 	MAPIO(omap_perseus2_map_io)
 	INITIRQ(omap_perseus2_init_irq)
-	INITTIME(omap_init_time)
 	INIT_MACHINE(omap_perseus2_init)
+	INITTIME(omap_init_time)
 MACHINE_END

arch/arm/mach-omap/clocks.c

@@ -36,6 +36,8 @@
 #include <asm/arch/clocks.h>
 #include <asm/arch/board.h>
 
+extern void start_mputimer1(unsigned long load_val);
+
 /* Input clock in MHz */
 static unsigned int source_clock = 12;
 
@@ -239,7 +241,7 @@ int ck_auto_unclock = 1;
 int ck_debug = 0;
 
 #define CK_MAX_PLL_FREQ		OMAP_CK_MAX_RATE
-static __u8 ck_valid_table[CK_MAX_PLL_FREQ / 8 + 1];
+static __u32 ck_valid_table[CK_MAX_PLL_FREQ / 32 + 1];
 static __u8 ck_lookup_table[CK_MAX_PLL_FREQ];
 
 int
@@ -615,11 +617,11 @@ __ck_make_lookup_table(void)
 int __init
 init_ck(void)
 {
-	const struct omap_clock_info *info;
+	const struct omap_clock_config *info;
 	int crystal_type = 0; /* Default 12 MHz */
 
 	__ck_make_lookup_table();
-	info = omap_get_per_info(OMAP_TAG_CLOCK, struct omap_clock_info);
+	info = omap_get_config(OMAP_TAG_CLOCK, struct omap_clock_config);
 	if (info != NULL) {
 		if (!cpu_is_omap1510())
 			crystal_type = info->system_clock_type;
@@ -645,7 +647,8 @@ init_ck(void)
 #elif defined(CONFIG_OMAP_ARM_182MHZ) && defined(CONFIG_ARCH_OMAP730)
 	omap_writew(0x250E, ARM_CKCTL);
 	omap_writew(0x2710, DPLL_CTL);
-#elif defined(CONFIG_OMAP_ARM_192MHZ) && (defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP5912))
+#elif defined(CONFIG_OMAP_ARM_192MHZ) && (defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP5912) \
+					  || defined(CONFIG_ARCH_OMAP1710))
 	omap_writew(0x150f, ARM_CKCTL);
 	if (crystal_type == 2) {
 		source_clock = 13;	/* MHz */

arch/arm/mach-omap/common.c

@@ -104,7 +104,7 @@ static struct map_desc omap1510_io_desc[] __initdata = {
 };
 #endif
 
-#ifdef CONFIG_ARCH_OMAP1610
+#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP1710)
 static struct map_desc omap1610_io_desc[] __initdata = {
  { OMAP1610_DSP_BASE,    OMAP1610_DSP_START,    OMAP1610_DSP_SIZE,    MT_DEVICE },
  { OMAP1610_DSPREG_BASE, OMAP1610_DSPREG_START, OMAP1610_DSPREG_SIZE, MT_DEVICE },
@@ -147,8 +147,8 @@ static void __init _omap_map_io(void)
 		iotable_init(omap1510_io_desc, ARRAY_SIZE(omap1510_io_desc));
 	}
 #endif
-#ifdef CONFIG_ARCH_OMAP1610
-	if (cpu_is_omap1610()) {
+#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP1710)
+	if (cpu_is_omap1610() || cpu_is_omap1710()) {
 		iotable_init(omap1610_io_desc, ARRAY_SIZE(omap1610_io_desc));
 	}
 #endif
@@ -181,13 +181,18 @@ void omap_map_io(void)
 extern int omap_bootloader_tag_len;
 extern u8 omap_bootloader_tag[];
 
-const void *__omap_get_per_info(u16 tag, size_t len)
+struct omap_board_config_kernel *omap_board_config;
+int omap_board_config_size = 0;
+
+const void *__omap_get_config(u16 tag, size_t len)
 {
-	struct omap_board_info_entry *info = NULL;
+	struct omap_board_config_entry *info = NULL;
+	struct omap_board_config_kernel *kinfo = NULL;
+	int i;
 
 #ifdef CONFIG_OMAP_BOOT_TAG
 	if (omap_bootloader_tag_len > 4)
-		info = (struct omap_board_info_entry *) omap_bootloader_tag;
+		info = (struct omap_board_config_entry *) omap_bootloader_tag;
 	while (info != NULL) {
 		u8 *next;
 
@@ -198,26 +203,38 @@ const void *__omap_get_per_info(u16 tag, size_t len)
 		if (next >= omap_bootloader_tag + omap_bootloader_tag_len)
 			info = NULL;
 		else
-			info = (struct omap_board_info_entry *) next;
+			info = (struct omap_board_config_entry *) next;
 	}
-#endif
-	if (info == NULL)
-		return NULL;
+	if (info != NULL) {
+		/* Check the length as a lame attempt to check for
+		 * binary inconsistancy. */
 		if (info->len != len) {
-		printk(KERN_ERR "OMAP per_info: Length mismatch with tag %x (want %d, got %d)\n",
+			printk(KERN_ERR "OMAP peripheral config: Length mismatch with tag %x (want %d, got %d)\n",
 			       tag, len, info->len);
 			return NULL;
 		}
-
 		return info->data;
+	}
+#endif
+	/* Try to find the config from the board-specific structures
+	 * in the kernel. */
+	for (i = 0; i < omap_board_config_size; i++) {
+		if (omap_board_config[i].tag == tag) {
+			kinfo = &omap_board_config[i];
+			break;
+		}
+	}
+	if (kinfo == NULL)
+		return NULL;
+	return kinfo->data;
 }
-EXPORT_SYMBOL(__omap_get_per_info);
+EXPORT_SYMBOL(__omap_get_config);
 
 static int __init omap_add_serial_console(void)
 {
-	const struct omap_uart_info *info;
+	const struct omap_uart_config *info;
 
-	info = omap_get_per_info(OMAP_TAG_UART, struct omap_uart_info);
+	info = omap_get_config(OMAP_TAG_UART, struct omap_uart_config);
 	if (info != NULL && info->console_uart) {
 		static char speed[11], *opt = NULL;
 

arch/arm/mach-omap/common.h

@@ -28,7 +28,6 @@
 #define __ARCH_ARM_MACH_OMAP_COMMON_H
 
 extern void omap_map_io(void);
-extern void omap_init_time(void);
 
 #endif /* __ARCH_ARM_MACH_OMAP_COMMON_H */
 

arch/arm/mach-omap/dma.c

@@ -118,7 +118,7 @@ void omap_set_dma_constant_fill(int lch, u32 color)
 	u16 w;
 
 #ifdef CONFIG_DEBUG_KERNEL
-	if (omap_dma_in_1510_mode) {
+	if (omap_dma_in_1510_mode()) {
 		printk(KERN_ERR "OMAP DMA constant fill not available in 1510 mode.");
 		BUG();
 		return;
@@ -141,7 +141,7 @@ void omap_set_dma_transparent_copy(int lch, u32 color)
 	u16 w;
 
 #ifdef CONFIG_DEBUG_KERNEL
-	if (omap_dma_in_1510_mode) {
+	if (omap_dma_in_1510_mode()) {
 		printk(KERN_ERR "OMAP DMA transparent copy not available in 1510 mode.");
 		BUG();
 	}
@@ -266,46 +266,78 @@ void omap_set_dma_dest_burst_mode(int lch, int burst_mode)
 	omap_writew(w, OMAP_DMA_CSDP(lch));
 }
 
-void omap_start_dma(int lch)
+static inline void init_intr(int lch)
 {
 	u16 w;
 
-	if (!omap_dma_in_1510_mode()) {
-		int next_lch;
+	/* Read CSR to make sure it's cleared. */
+	w = omap_readw(OMAP_DMA_CSR(lch));
+	/* Enable some nice interrupts. */
+	omap_writew(dma_chan[lch].enabled_irqs, OMAP_DMA_CICR(lch));
+	dma_chan[lch].flags |= OMAP_DMA_ACTIVE;
+}
 
-		next_lch = dma_chan[lch].next_lch;
+static inline void enable_lnk(int lch)
+{
+	u16 w;
 
-		/* Enable the queue, if needed so. */
-		if (next_lch != -1) {
 	/* Clear the STOP_LNK bits */
 	w = omap_readw(OMAP_DMA_CLNK_CTRL(lch));
 	w &= ~(1 << 14);
 	omap_writew(w, OMAP_DMA_CLNK_CTRL(lch));
-			w = omap_readw(OMAP_DMA_CLNK_CTRL(next_lch));
-			w &= ~(1 << 14);
-			omap_writew(w, OMAP_DMA_CLNK_CTRL(next_lch));
 
 	/* And set the ENABLE_LNK bits */
-			omap_writew(next_lch | (1 << 15),
+	if (dma_chan[lch].next_lch != -1)
+		omap_writew(dma_chan[lch].next_lch | (1 << 15),
 			    OMAP_DMA_CLNK_CTRL(lch));
-			/* The loop case */
-			if (dma_chan[next_lch].next_lch == lch)
-				omap_writew(lch | (1 << 15),
-					    OMAP_DMA_CLNK_CTRL(next_lch));
+}
 
-			/* Read CSR to make sure it's cleared. */
-			w = omap_readw(OMAP_DMA_CSR(next_lch));
-			/* Enable some nice interrupts. */
-			omap_writew(dma_chan[next_lch].enabled_irqs,
-				    OMAP_DMA_CICR(next_lch));
-			dma_chan[next_lch].flags |= OMAP_DMA_ACTIVE;
-		}
+static inline void disable_lnk(int lch)
+{
+	u16 w;
+
+	/* Disable interrupts */
+	omap_writew(0, OMAP_DMA_CICR(lch));
+
+	/* Set the STOP_LNK bit */
+	w = omap_readw(OMAP_DMA_CLNK_CTRL(lch));
+	w |= (1 << 14);
+	w = omap_writew(w, OMAP_DMA_CLNK_CTRL(lch));
+
+	dma_chan[lch].flags &= ~OMAP_DMA_ACTIVE;
+}
+
+void omap_start_dma(int lch)
+{
+	u16 w;
+
+	if (!omap_dma_in_1510_mode() && dma_chan[lch].next_lch != -1) {
+		int next_lch, cur_lch;
+		char dma_chan_link_map[OMAP_LOGICAL_DMA_CH_COUNT];
+
+		dma_chan_link_map[lch] = 1;
+		/* Set the link register of the first channel */
+		enable_lnk(lch);
+
+		memset(dma_chan_link_map, 0, sizeof(dma_chan_link_map));
+		cur_lch = dma_chan[lch].next_lch;
+		do {
+			next_lch = dma_chan[cur_lch].next_lch;
+
+                        /* The loop case: we've been here already */
+			if (dma_chan_link_map[cur_lch])
+				break;
+			/* Mark the current channel */
+			dma_chan_link_map[cur_lch] = 1;
+
+			enable_lnk(cur_lch);
+			init_intr(cur_lch);
+
+			cur_lch = next_lch;
+		} while (next_lch != -1);
 	}
 
-	/* Read CSR to make sure it's cleared. */
-	w = omap_readw(OMAP_DMA_CSR(lch));
-	/* Enable some nice interrupts. */
-	omap_writew(dma_chan[lch].enabled_irqs, OMAP_DMA_CICR(lch));
+	init_intr(lch);
 
 	w = omap_readw(OMAP_DMA_CCR(lch));
 	w |= OMAP_DMA_CCR_EN;
@@ -316,37 +348,34 @@ void omap_start_dma(int lch)
 void omap_stop_dma(int lch)
 {
 	u16 w;
-	int next_lch;
 
+	if (!omap_dma_in_1510_mode() && dma_chan[lch].next_lch != -1) {
+		int next_lch, cur_lch = lch;
+		char dma_chan_link_map[OMAP_LOGICAL_DMA_CH_COUNT];
+
+		memset(dma_chan_link_map, 0, sizeof(dma_chan_link_map));
+		do {
+			/* The loop case: we've been here already */
+			if (dma_chan_link_map[cur_lch])
+				break;
+			/* Mark the current channel */
+			dma_chan_link_map[cur_lch] = 1;
+
+			disable_lnk(cur_lch);
+
+			next_lch = dma_chan[cur_lch].next_lch;
+			cur_lch = next_lch;
+		} while (next_lch != -1);
+
+		return;
+	}
 	/* Disable all interrupts on the channel */
 	omap_writew(0, OMAP_DMA_CICR(lch));
 
-	if (omap_dma_in_1510_mode()) {
 	w = omap_readw(OMAP_DMA_CCR(lch));
 	w &= ~OMAP_DMA_CCR_EN;
 	omap_writew(w, OMAP_DMA_CCR(lch));
 	dma_chan[lch].flags &= ~OMAP_DMA_ACTIVE;
-		return;
-	}
-
-	next_lch = dma_chan[lch].next_lch;
-
-	/*
-	 * According to thw HW spec, enabling the STOP_LNK bit
-	 * resets the CCR_EN bit at the same time.
-	 */
-	w = omap_readw(OMAP_DMA_CLNK_CTRL(lch));
-	w |= (1 << 14);
-	w = omap_writew(w, OMAP_DMA_CLNK_CTRL(lch));
-	dma_chan[lch].flags &= ~OMAP_DMA_ACTIVE;
-
-	if (next_lch != -1) {
-		omap_writew(0, OMAP_DMA_CICR(next_lch));
-		w = omap_readw(OMAP_DMA_CLNK_CTRL(next_lch));
-		w |= (1 << 14);
-		w = omap_writew(w, OMAP_DMA_CLNK_CTRL(next_lch));
-		dma_chan[next_lch].flags &= ~OMAP_DMA_ACTIVE;
-	}
 }
 
 void omap_enable_dma_irq(int lch, u16 bits)
@@ -445,7 +474,7 @@ int omap_request_dma(int dev_id, const char *dev_name,
 	chan->data = data;
 	chan->enabled_irqs = OMAP_DMA_TOUT_IRQ | OMAP_DMA_DROP_IRQ | OMAP_DMA_BLOCK_IRQ;
 
-	if (cpu_is_omap1610() || cpu_is_omap5912()) {
+	if (cpu_is_omap1610() || cpu_is_omap5912() || cpu_is_omap730() || cpu_is_omap1710()) {
 		/* If the sync device is set, configure it dynamically. */
 		if (dev_id != 0) {
 			set_gdma_dev(free_ch + 1, dev_id);
@@ -533,7 +562,6 @@ void omap_dma_unlink_lch (int lch_head, int lch_queue)
 	}
 
 	dma_chan[lch_head].next_lch = -1;
-	dma_chan[lch_queue].next_lch = -1;
 }
 
 
@@ -713,7 +741,7 @@ static int __init omap_init_dma(void)
 		printk(KERN_INFO "DMA support for OMAP1510 initialized\n");
 		dma_chan_count = 9;
 		enable_1510_mode = 1;
-	} else if (cpu_is_omap1610() || cpu_is_omap5912()) {
+	} else if (cpu_is_omap1610() || cpu_is_omap5912() || cpu_is_omap730() || cpu_is_omap1710()) {
 		printk(KERN_INFO "OMAP DMA hardware version %d\n",
 		       omap_readw(OMAP_DMA_HW_ID));
 		printk(KERN_INFO "DMA capabilities: %08x:%08x:%04x:%04x:%04x\n",
@@ -771,6 +799,8 @@ EXPORT_SYMBOL(omap_request_dma);
 EXPORT_SYMBOL(omap_free_dma);
 EXPORT_SYMBOL(omap_start_dma);
 EXPORT_SYMBOL(omap_stop_dma);
+EXPORT_SYMBOL(omap_enable_dma_irq);
+EXPORT_SYMBOL(omap_disable_dma_irq);
 
 EXPORT_SYMBOL(omap_set_dma_transfer_params);
 EXPORT_SYMBOL(omap_set_dma_constant_fill);

arch/arm/mach-omap/fpga.c

@@ -31,19 +31,9 @@
 #include <asm/arch/fpga.h>
 #include <asm/arch/gpio.h>
 
-unsigned char fpga_read(int reg)
-{
-	return __raw_readb(reg);
-}
-
-void fpga_write(unsigned char val, int reg)
-{
-	__raw_writeb(val, reg);
-}
-
 static void fpga_mask_irq(unsigned int irq)
 {
-	irq -= IH_FPGA_BASE;
+	irq -= OMAP1510_IH_FPGA_BASE;
 
 	if (irq < 8)
 		__raw_writeb((__raw_readb(OMAP1510_FPGA_IMR_LO)
@@ -76,7 +66,7 @@ static void fpga_ack_irq(unsigned int irq)
 
 static void fpga_unmask_irq(unsigned int irq)
 {
-	irq -= IH_FPGA_BASE;
+	irq -= OMAP1510_IH_FPGA_BASE;
 
 	if (irq < 8)
 		__raw_writeb((__raw_readb(OMAP1510_FPGA_IMR_LO) | (1 << irq)),
@@ -114,8 +104,8 @@ void innovator_fpga_IRQ_demux(unsigned int irq, struct irqdesc *desc,
 			break;
 		}
 
-		for (fpga_irq = IH_FPGA_BASE;
-			(fpga_irq < (IH_FPGA_BASE + NR_FPGA_IRQS)) && stat;
+		for (fpga_irq = OMAP1510_IH_FPGA_BASE;
+			(fpga_irq < (OMAP1510_IH_FPGA_BASE + NR_FPGA_IRQS)) && stat;
 			fpga_irq++, stat >>= 1) {
 			if (stat & 1) {
 				d = irq_desc + fpga_irq;
@@ -162,7 +152,7 @@ static struct irqchip omap_fpga_irq = {
  * interrupts at the interrupt controller via disable_irq/enable_irq
  * could pose a problem.
  */
-void fpga_init_irq(void)
+void omap1510_fpga_init_irq(void)
 {
 	int i;
 
@@ -170,9 +160,9 @@ void fpga_init_irq(void)
 	__raw_writeb(0, OMAP1510_FPGA_IMR_HI);
 	__raw_writeb(0, INNOVATOR_FPGA_IMR2);
 
-	for (i = IH_FPGA_BASE; i < (IH_FPGA_BASE + NR_FPGA_IRQS); i++) {
+	for (i = OMAP1510_IH_FPGA_BASE; i < (OMAP1510_IH_FPGA_BASE + NR_FPGA_IRQS); i++) {
 
-		if (i == INT_FPGA_TS) {
+		if (i == OMAP1510_INT_FPGA_TS) {
 			/*
 			 * The touchscreen interrupt is level-sensitive, so
 			 * we'll use the regular mask_ack routine for it.
@@ -201,9 +191,7 @@ void fpga_init_irq(void)
 	omap_request_gpio(13);
 	omap_set_gpio_direction(13, 1);
 	omap_set_gpio_edge_ctrl(13, OMAP_GPIO_RISING_EDGE);
-	set_irq_chained_handler(INT_FPGA, innovator_fpga_IRQ_demux);
+	set_irq_chained_handler(OMAP1510_INT_FPGA, innovator_fpga_IRQ_demux);
 }
 
-EXPORT_SYMBOL(fpga_init_irq);
-EXPORT_SYMBOL(fpga_read);
-EXPORT_SYMBOL(fpga_write);
+EXPORT_SYMBOL(omap1510_fpga_init_irq);

arch/arm/mach-omap/gpio.c

@@ -94,7 +94,7 @@ struct gpio_bank {
 #define METHOD_GPIO_1610	2
 #define METHOD_GPIO_730		3
 
-#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP5912)
+#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP1710) || defined(CONFIG_ARCH_OMAP5912)
 static struct gpio_bank gpio_bank_1610[5] = {
 	{ OMAP_MPUIO_BASE,     INT_MPUIO,	    IH_MPUIO_BASE,     METHOD_MPUIO},
 	{ OMAP1610_GPIO1_BASE, INT_GPIO_BANK1,	    IH_GPIO_BASE,      METHOD_GPIO_1610 },
@@ -113,7 +113,7 @@ static struct gpio_bank gpio_bank_1510[2] = {
 
 #ifdef CONFIG_ARCH_OMAP730
 static struct gpio_bank gpio_bank_730[7] = {
-	{ OMAP_MPUIO_BASE,     INT_MPUIO,	    IH_MPUIO_BASE,	METHOD_MPUIO },
+	{ OMAP_MPUIO_BASE,     INT_730_MPUIO,	    IH_MPUIO_BASE,	METHOD_MPUIO },
 	{ OMAP730_GPIO1_BASE,  INT_GPIO_BANK1,	    IH_GPIO_BASE,	METHOD_GPIO_730 },
 	{ OMAP730_GPIO2_BASE,  INT_730_GPIO_BANK2,  IH_GPIO_BASE + 32,	METHOD_GPIO_730 },
 	{ OMAP730_GPIO3_BASE,  INT_730_GPIO_BANK3,  IH_GPIO_BASE + 64,	METHOD_GPIO_730 },
@@ -135,8 +135,8 @@ static inline struct gpio_bank *get_gpio_bank(int gpio)
 		return &gpio_bank[1];
 	}
 #endif
-#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP5912)
-	if (cpu_is_omap1610() || cpu_is_omap5912()) {
+#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP1710) || defined(CONFIG_ARCH_OMAP5912)
+	if (cpu_is_omap1610() || cpu_is_omap1710() || cpu_is_omap5912()) {
 		if (OMAP_GPIO_IS_MPUIO(gpio))
 			return &gpio_bank[0];
 		return &gpio_bank[1 + (gpio >> 4)];
@@ -172,8 +172,8 @@ static inline int gpio_valid(int gpio)
 	if (cpu_is_omap1510() && gpio < 16)
 		return 0;
 #endif
-#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP5912)
-	if ((cpu_is_omap1610() || cpu_is_omap5912()) && gpio < 64)
+#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP1710) || defined(CONFIG_ARCH_OMAP5912)
+	if ((cpu_is_omap1610() || cpu_is_omap1710() || cpu_is_omap5912()) && gpio < 64)
 		return 0;
 #endif
 #ifdef CONFIG_ARCH_OMAP730
@@ -554,7 +554,7 @@ static void gpio_irq_handler(unsigned int irq, struct irqdesc *desc,
 	if (bank->method == METHOD_GPIO_1510)
 		isr_reg = bank->base + OMAP1510_GPIO_INT_STATUS;
 #endif
-#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP5912)
+#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP1710) || defined(CONFIG_ARCH_OMAP5912)
 	if (bank->method == METHOD_GPIO_1610)
 		isr_reg = bank->base + OMAP1610_GPIO_IRQSTATUS1;
 #endif
@@ -588,7 +588,7 @@ static void gpio_ack_irq(unsigned int irq)
 	if (bank->method == METHOD_GPIO_1510)
 		__raw_writew(1 << (gpio & 0x0f), bank->base + OMAP1510_GPIO_INT_STATUS);
 #endif
-#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP5912)
+#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP1710) || defined(CONFIG_ARCH_OMAP5912)
 	if (bank->method == METHOD_GPIO_1610)
 		__raw_writew(1 << (gpio & 0x0f), bank->base + OMAP1610_GPIO_IRQSTATUS1);
 #endif
@@ -629,7 +629,7 @@ static void mpuio_mask_irq(unsigned int irq)
 	unsigned int gpio = OMAP_MPUIO(irq - IH_MPUIO_BASE);
 	struct gpio_bank *bank = get_gpio_bank(gpio);
 
-	_set_gpio_irqenable(bank, gpio, 0);
+	_set_gpio_irqenable(bank, get_gpio_index(gpio), 0);
 }
 
 static void mpuio_unmask_irq(unsigned int irq)
@@ -637,7 +637,7 @@ static void mpuio_unmask_irq(unsigned int irq)
 	unsigned int gpio = OMAP_MPUIO(irq - IH_MPUIO_BASE);
 	struct gpio_bank *bank = get_gpio_bank(gpio);
 
-	_set_gpio_irqenable(bank, gpio, 1);
+	_set_gpio_irqenable(bank, get_gpio_index(gpio), 1);
 }
 
 static struct irqchip gpio_irq_chip = {
@@ -668,8 +668,8 @@ static int __init _omap_gpio_init(void)
 		gpio_bank = gpio_bank_1510;
 	}
 #endif
-#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP5912)
-	if (cpu_is_omap1610() || cpu_is_omap5912()) {
+#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP1710) || defined(CONFIG_ARCH_OMAP5912)
+	if (cpu_is_omap1610() || cpu_is_omap1710() || cpu_is_omap5912()) {
 		int rev;
 
 		gpio_bank_count = 5;
@@ -702,7 +702,7 @@ static int __init _omap_gpio_init(void)
 			__raw_writew(0x0000, bank->base + OMAP1510_GPIO_INT_STATUS);
 		}
 #endif
-#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP5912)
+#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP1710) || defined(CONFIG_ARCH_OMAP5912)
 		if (bank->method == METHOD_GPIO_1610) {
 			__raw_writew(0x0000, bank->base + OMAP1610_GPIO_IRQENABLE1);
 			__raw_writew(0xffff, bank->base + OMAP1610_GPIO_IRQSTATUS1);
@@ -731,7 +731,7 @@ static int __init _omap_gpio_init(void)
 
 	/* Enable system clock for GPIO module.
 	 * The CAM_CLK_CTRL *is* really the right place. */
-	if (cpu_is_omap1610())
+	if (cpu_is_omap1610() || cpu_is_omap1710())
 		omap_writel(omap_readl(ULPD_CAM_CLK_CTRL) | 0x04, ULPD_CAM_CLK_CTRL);
 
 	return 0;

arch/arm/mach-omap/irq.c

@@ -140,7 +140,9 @@ static struct omap_irq_bank omap1510_irq_banks[] = {
 };
 #endif
 
-#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP5912)
+#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP5912) \
+				  || defined(CONFIG_ARCH_OMAP1710)
+
 static struct omap_irq_bank omap1610_irq_banks[] = {
 	{ .base_reg = OMAP_IH1_BASE, 		.trigger_map = 0xb3fefe8f },
 	{ .base_reg = OMAP_IH2_BASE, 		.trigger_map = 0xfffff7ff },
@@ -171,8 +173,9 @@ void __init omap_init_irq(void)
 		irq_bank_count = ARRAY_SIZE(omap1510_irq_banks);
 	}
 #endif
-#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP5912)
-	if (cpu_is_omap1610() || cpu_is_omap5912()) {
+#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP5912) \
+				  || defined(CONFIG_ARCH_OMAP1710)
+	if (cpu_is_omap1610() || cpu_is_omap5912() || cpu_is_omap1710()) {
 		irq_banks = omap1610_irq_banks;
 		irq_bank_count = ARRAY_SIZE(omap1610_irq_banks);
 	}
@@ -190,6 +193,11 @@ void __init omap_init_irq(void)
 	irq_bank_writel(0x03, 0, IRQ_CONTROL_REG_OFFSET);
 	irq_bank_writel(0x03, 1, IRQ_CONTROL_REG_OFFSET);
 
+	/* Enable interrupts in global mask */
+	if (cpu_is_omap730()) {
+		irq_bank_writel(0x0, 0, IRQ_GMR_REG_OFFSET);
+	}
+
 	/* Install the interrupt handlers for each bank */
 	for (i = 0; i < irq_bank_count; i++) {
 		for (j = i * 32; j < (i + 1) * 32; j++) {
@@ -205,5 +213,9 @@ void __init omap_init_irq(void)
 	}
 
 	/* Unmask level 2 handler */
+	if (cpu_is_omap730()) {
+		omap_unmask_irq(INT_730_IH2_IRQ);
+	} else {
 		omap_unmask_irq(INT_IH2_IRQ);
+	}
 }

arch/arm/mach-omap/leds.c

@@ -3,6 +3,7 @@
  *
  * OMAP LEDs dispatcher
  */
+#include <linux/kernel.h>
 #include <linux/init.h>
 
 #include <asm/leds.h>
@@ -11,17 +12,17 @@
 #include "leds.h"
 
 static int __init
-omap1510_leds_init(void)
+omap_leds_init(void)
 {
 	if (machine_is_omap_innovator())
 		leds_event = innovator_leds_event;
 
-	else if (machine_is_omap_perseus2()) {
-		leds_event = perseus2_leds_event;
+	else if (machine_is_omap_h2() || machine_is_omap_perseus2()) {
+		leds_event = h2p2_dbg_leds_event;
 	}
 
 	leds_event(led_start);
 	return 0;
 }
 
-__initcall(omap1510_leds_init);
+__initcall(omap_leds_init);

arch/arm/mach-omap/leds.h

 extern void innovator_leds_event(led_event_t evt);
-extern void perseus2_leds_event(led_event_t evt);
+extern void h2p2_dbg_leds_event(led_event_t evt);

arch/arm/mach-omap/ocpi.c

@@ -59,8 +59,8 @@ int ocpi_enable(void)
 
 	/* Make sure there's clock for OCPI */
 
-#ifdef CONFIG_ARCH_OMAP1610
-        if (cpu_is_omap1610()) {
+#if defined(CONFIG_ARCH_OMAP1610) || defined(CONFIG_ARCH_OMAP1710)
+        if (cpu_is_omap1610() || cpu_is_omap1710()) {
 		val = omap_readl(OMAP1610_ARM_IDLECT3);
 		val |= EN_OCPI_CK;
 		val &= ~IDLOCPI_ARM;