Merge branch 'net-qualcomm-add-QCA7000-UART-driver'

Stefan Wahren says:

====================
net: qualcomm: add QCA7000 UART driver

The Qualcomm QCA7000 HomePlug GreenPHY supports two interfaces:
UART and SPI. This patch series adds the missing support for UART.

This driver based on the Qualcomm code [1], but contains some changes:
* use random MAC address per default
* use net_device_stats from device
* share frame decoding between SPI and UART driver
* improve error handling
* reimplement tty_wakeup with work queue (based on slcan)
* use new serial device bus instead of ldisc

The patches 1 - 3 are just for clean up and are not related to
the UART support. Patch 4 adds SET_NETDEV_DEV() to qca_spi.
Patches 5 - 16 prepare the existing QCA7000 code for UART support.
The last patch contains the new driver.

The code itself has been tested on a Freescale i.MX28 board and
a Raspberry Pi Zero.

Changes in v8:
  * add necessary header includes to qca_7k.c in order to reflect
    dependencies

Changes in v7:
  * fix race between tx workqueue and device deregistration (reported by Lino)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/qca,qca7000.txt

+* Qualcomm QCA7000
+
+The QCA7000 is a serial-to-powerline bridge with a host interface which could
+be configured either as SPI or UART slave. This configuration is done by
+the QCA7000 firmware.
+
+(a) Ethernet over SPI
+
+In order to use the QCA7000 as SPI device it must be defined as a child of a
+SPI master in the device tree.
+
+Required properties:
+- compatible	    : Should be "qca,qca7000"
+- reg		    : Should specify the SPI chip select
+- interrupts	    : The first cell should specify the index of the source
+		      interrupt and the second cell should specify the trigger
+		      type as rising edge
+- spi-cpha	    : Must be set
+- spi-cpol	    : Must be set
+
+Optional properties:
+- interrupt-parent  : Specify the pHandle of the source interrupt
+- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at.
+		      Numbers smaller than 1000000 or greater than 16000000
+		      are invalid. Missing the property will set the SPI
+		      frequency to 8000000 Hertz.
+- local-mac-address : see ./ethernet.txt
+- qca,legacy-mode   : Set the SPI data transfer of the QCA7000 to legacy mode.
+		      In this mode the SPI master must toggle the chip select
+		      between each data word. In burst mode these gaps aren't
+		      necessary, which is faster. This setting depends on how
+		      the QCA7000 is setup via GPIO pin strapping. If the
+		      property is missing the driver defaults to burst mode.
+
+SPI Example:
+
+/* Freescale i.MX28 SPI master*/
+ssp2: spi@80014000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+
+	qca7000: ethernet@0 {
+		compatible = "qca,qca7000";
+		reg = <0x0>;
+		interrupt-parent = <&gpio3>;      /* GPIO Bank 3 */
+		interrupts = <25 0x1>;            /* Index: 25, rising edge */
+		spi-cpha;                         /* SPI mode: CPHA=1 */
+		spi-cpol;                         /* SPI mode: CPOL=1 */
+		spi-max-frequency = <8000000>;    /* freq: 8 MHz */
+		local-mac-address = [ A0 B0 C0 D0 E0 F0 ];
+	};
+};
+
+(b) Ethernet over UART
+
+In order to use the QCA7000 as UART slave it must be defined as a child of a
+UART master in the device tree. It is possible to preconfigure the UART
+settings of the QCA7000 firmware, but it's not possible to change them during
+runtime.
+
+Required properties:
+- compatible        : Should be "qca,qca7000"
+
+Optional properties:
+- local-mac-address : see ./ethernet.txt
+- current-speed     : current baud rate of QCA7000 which defaults to 115200
+		      if absent, see also ../serial/slave-device.txt
+
+UART Example:
+
+/* Freescale i.MX28 UART */
+auart0: serial@8006a000 {
+	compatible = "fsl,imx28-auart", "fsl,imx23-auart";
+	reg = <0x8006a000 0x2000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_2pins_a>;
+	status = "okay";
+
+	qca7000: ethernet {
+		compatible = "qca,qca7000";
+		local-mac-address = [ A0 B0 C0 D0 E0 F0 ];
+		current-speed = <38400>;
+	};
+};

Documentation/devicetree/bindings/net/qca-qca7000-spi.txt

-* Qualcomm QCA7000 (Ethernet over SPI protocol)
-
-Note: The QCA7000 is useable as a SPI device. In this case it must be defined
-as a child of a SPI master in the device tree.
-
-Required properties:
-- compatible : Should be "qca,qca7000"
-- reg : Should specify the SPI chip select
-- interrupts : The first cell should specify the index of the source interrupt
-  and the second cell should specify the trigger type as rising edge
-- spi-cpha : Must be set
-- spi-cpol: Must be set
-
-Optional properties:
-- interrupt-parent : Specify the pHandle of the source interrupt
-- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at.
-  Numbers smaller than 1000000 or greater than 16000000 are invalid. Missing
-  the property will set the SPI frequency to 8000000 Hertz.
-- local-mac-address: 6 bytes, MAC address
-- qca,legacy-mode : Set the SPI data transfer of the QCA7000 to legacy mode.
-  In this mode the SPI master must toggle the chip select between each data
-  word. In burst mode these gaps aren't necessary, which is faster.
-  This setting depends on how the QCA7000 is setup via GPIO pin strapping.
-  If the property is missing the driver defaults to burst mode.
-
-Example:
-
-/* Freescale i.MX28 SPI master*/
-ssp2: spi@80014000 {
-	#address-cells = <1>;
-	#size-cells = <0>;
-	compatible = "fsl,imx28-spi";
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi2_pins_a>;
-	status = "okay";
-
-	qca7000: ethernet@0 {
-		compatible = "qca,qca7000";
-		reg = <0x0>;
-		interrupt-parent = <&gpio3>;      /* GPIO Bank 3 */
-		interrupts = <25 0x1>;            /* Index: 25, rising edge */
-		spi-cpha;                         /* SPI mode: CPHA=1 */
-		spi-cpol;                         /* SPI mode: CPOL=1 */
-		spi-max-frequency = <8000000>;    /* freq: 8 MHz */
-		local-mac-address = [ A0 B0 C0 D0 E0 F0 ];
-	};
-};

Documentation/devicetree/bindings/serial/slave-device.txt

@@ -21,6 +21,15 @@ Optional Properties:
 		  can support. For example, a particular board has some signal
 		  quality issue or the host processor can't support higher
 		  baud rates.
+- current-speed	: The current baud rate the device operates at. This should
+		  only be present in case a driver has no chance to know
+		  the baud rate of the slave device.
+		  Examples:
+		    * device supports auto-baud
+		    * the rate is setup by a bootloader and there is no
+		      way to reset the device
+		    * device baud rate is configured by its firmware but
+		      there is no way to request the actual settings
 
 Example:
 

drivers/net/ethernet/qualcomm/Kconfig

@@ -16,7 +16,13 @@ config NET_VENDOR_QUALCOMM
 if NET_VENDOR_QUALCOMM
 
 config QCA7000
-	tristate "Qualcomm Atheros QCA7000 support"
+	tristate
+	help
+	  This enables support for the Qualcomm Atheros QCA7000.
+
+config QCA7000_SPI
+	tristate "Qualcomm Atheros QCA7000 SPI support"
+	select QCA7000
 	depends on SPI_MASTER && OF
 	---help---
 	  This SPI protocol driver supports the Qualcomm Atheros QCA7000.
@@ -24,6 +30,22 @@ config QCA7000
 	  To compile this driver as a module, choose M here. The module
 	  will be called qcaspi.
 
+config QCA7000_UART
+	tristate "Qualcomm Atheros QCA7000 UART support"
+	select QCA7000
+	depends on SERIAL_DEV_BUS && OF
+	---help---
+	  This UART protocol driver supports the Qualcomm Atheros QCA7000.
+
+	  Currently the driver assumes these device UART settings:
+	    Data bits: 8
+	    Parity: None
+	    Stop bits: 1
+	    Flow control: None
+
+	  To compile this driver as a module, choose M here. The module
+	  will be called qcauart.
+
 config QCOM_EMAC
 	tristate "Qualcomm Technologies, Inc. EMAC Gigabit Ethernet support"
 	depends on HAS_DMA && HAS_IOMEM

drivers/net/ethernet/qualcomm/Makefile

@@ -2,7 +2,10 @@
 # Makefile for the Qualcomm network device drivers.
 #
 
-obj-$(CONFIG_QCA7000) += qcaspi.o
-qcaspi-objs := qca_spi.o qca_framing.o qca_7k.o qca_debug.o
+obj-$(CONFIG_QCA7000) += qca_7k_common.o
+obj-$(CONFIG_QCA7000_SPI) += qcaspi.o
+qcaspi-objs := qca_7k.o qca_debug.o qca_spi.o
+obj-$(CONFIG_QCA7000_UART) += qcauart.o
+qcauart-objs := qca_uart.o
 
 obj-y += emac/

drivers/net/ethernet/qualcomm/qca_7k.c

@@ -23,11 +23,9 @@
  *   kernel-based SPI device.
  */
 
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/moduleparam.h>
+#include <linux/kernel.h>
+#include <linux/netdevice.h>
 #include <linux/spi/spi.h>
-#include <linux/version.h>
 
 #include "qca_7k.h"
 
@@ -123,27 +121,3 @@ qcaspi_write_register(struct qcaspi *qca, u16 reg, u16 value)
 
 	return ret;
 }
-
-int
-qcaspi_tx_cmd(struct qcaspi *qca, u16 cmd)
-{
-	__be16 tx_data;
-	struct spi_message *msg = &qca->spi_msg1;
-	struct spi_transfer *transfer = &qca->spi_xfer1;
-	int ret;
-
-	tx_data = cpu_to_be16(cmd);
-	transfer->len = sizeof(tx_data);
-	transfer->tx_buf = &tx_data;
-	transfer->rx_buf = NULL;
-
-	ret = spi_sync(qca->spi_dev, msg);
-
-	if (!ret)
-		ret = msg->status;
-
-	if (ret)
-		qcaspi_spi_error(qca);
-
-	return ret;
-}

drivers/net/ethernet/qualcomm/qca_7k.h

@@ -54,19 +54,18 @@
 #define SPI_REG_ACTION_CTRL     0x1B00
 
 /*   SPI_CONFIG register definition;             */
-#define QCASPI_SLAVE_RESET_BIT (1 << 6)
+#define QCASPI_SLAVE_RESET_BIT  BIT(6)
 
 /*   INTR_CAUSE/ENABLE register definition.      */
-#define SPI_INT_WRBUF_BELOW_WM (1 << 10)
-#define SPI_INT_CPU_ON         (1 << 6)
-#define SPI_INT_ADDR_ERR       (1 << 3)
-#define SPI_INT_WRBUF_ERR      (1 << 2)
-#define SPI_INT_RDBUF_ERR      (1 << 1)
-#define SPI_INT_PKT_AVLBL      (1 << 0)
+#define SPI_INT_WRBUF_BELOW_WM  BIT(10)
+#define SPI_INT_CPU_ON          BIT(6)
+#define SPI_INT_ADDR_ERR        BIT(3)
+#define SPI_INT_WRBUF_ERR       BIT(2)
+#define SPI_INT_RDBUF_ERR       BIT(1)
+#define SPI_INT_PKT_AVLBL       BIT(0)
 
 void qcaspi_spi_error(struct qcaspi *qca);
 int qcaspi_read_register(struct qcaspi *qca, u16 reg, u16 *result);
 int qcaspi_write_register(struct qcaspi *qca, u16 reg, u16 value);
-int qcaspi_tx_cmd(struct qcaspi *qca, u16 cmd);
 
 #endif /* _QCA_7K_H */

drivers/net/ethernet/qualcomm/qca_framing.c → drivers/net/ethernet/qualcomm/qca_7k_common.c

@@ -21,9 +21,11 @@
  *   by an atheros frame while transmitted over a serial channel;
  */
 
+#include <linux/init.h>
 #include <linux/kernel.h>
+#include <linux/module.h>
 
-#include "qca_framing.h"
+#include "qca_7k_common.h"
 
 u16
 qcafrm_create_header(u8 *buf, u16 length)
@@ -46,6 +48,7 @@ qcafrm_create_header(u8 *buf, u16 length)
 
 	return QCAFRM_HEADER_LEN;
 }
+EXPORT_SYMBOL_GPL(qcafrm_create_header);
 
 u16
 qcafrm_create_footer(u8 *buf)
@@ -57,6 +60,7 @@ qcafrm_create_footer(u8 *buf)
 	buf[1] = 0x55;
 	return QCAFRM_FOOTER_LEN;
 }
+EXPORT_SYMBOL_GPL(qcafrm_create_footer);
 
 /*   Gather received bytes and try to extract a full ethernet frame by
  *   following a simple state machine.
@@ -83,7 +87,7 @@ qcafrm_fsm_decode(struct qcafrm_handle *handle, u8 *buf, u16 buf_len, u8 recv_by
 
 		if (recv_byte != 0x00) {
 			/* first two bytes of length must be 0 */
-			handle->state = QCAFRM_HW_LEN0;
+			handle->state = handle->init;
 		}
 		break;
 	case QCAFRM_HW_LEN2:
@@ -97,7 +101,7 @@ qcafrm_fsm_decode(struct qcafrm_handle *handle, u8 *buf, u16 buf_len, u8 recv_by
 	case QCAFRM_WAIT_AA4:
 		if (recv_byte != 0xAA) {
 			ret = QCAFRM_NOHEAD;
-			handle->state = QCAFRM_HW_LEN0;
+			handle->state = handle->init;
 		} else {
 			handle->state--;
 		}
@@ -117,9 +121,9 @@ qcafrm_fsm_decode(struct qcafrm_handle *handle, u8 *buf, u16 buf_len, u8 recv_by
 		break;
 	case QCAFRM_WAIT_RSVD_BYTE2:
 		len = handle->offset;
-		if (len > buf_len || len < QCAFRM_ETHMINLEN) {
+		if (len > buf_len || len < QCAFRM_MIN_LEN) {
 			ret = QCAFRM_INVLEN;
-			handle->state = QCAFRM_HW_LEN0;
+			handle->state = handle->init;
 		} else {
 			handle->state = (enum qcafrm_state)(len + 1);
 			/* Remaining number of bytes. */
@@ -135,7 +139,7 @@ qcafrm_fsm_decode(struct qcafrm_handle *handle, u8 *buf, u16 buf_len, u8 recv_by
 	case QCAFRM_WAIT_551:
 		if (recv_byte != 0x55) {
 			ret = QCAFRM_NOTAIL;
-			handle->state = QCAFRM_HW_LEN0;
+			handle->state = handle->init;
 		} else {
 			handle->state = QCAFRM_WAIT_552;
 		}
@@ -143,14 +147,20 @@ qcafrm_fsm_decode(struct qcafrm_handle *handle, u8 *buf, u16 buf_len, u8 recv_by
 	case QCAFRM_WAIT_552:
 		if (recv_byte != 0x55) {
 			ret = QCAFRM_NOTAIL;
-			handle->state = QCAFRM_HW_LEN0;
+			handle->state = handle->init;
 		} else {
 			ret = handle->offset;
 			/* Frame is fully received. */
-			handle->state = QCAFRM_HW_LEN0;
+			handle->state = handle->init;
 		}
 		break;
 	}
 
 	return ret;
 }
+EXPORT_SYMBOL_GPL(qcafrm_fsm_decode);
+
+MODULE_DESCRIPTION("Qualcomm Atheros QCA7000 common");
+MODULE_AUTHOR("Qualcomm Atheros Communications");
+MODULE_AUTHOR("Stefan Wahren <stefan.wahren@i2se.com>");
+MODULE_LICENSE("Dual BSD/GPL");

drivers/net/ethernet/qualcomm/qca_framing.h → drivers/net/ethernet/qualcomm/qca_7k_common.h

@@ -44,12 +44,12 @@
 #define QCAFRM_INVFRAME (QCAFRM_ERR_BASE - 4)
 
 /* Min/Max Ethernet MTU: 46/1500 */
-#define QCAFRM_ETHMINMTU (ETH_ZLEN - ETH_HLEN)
-#define QCAFRM_ETHMAXMTU ETH_DATA_LEN
+#define QCAFRM_MIN_MTU (ETH_ZLEN - ETH_HLEN)
+#define QCAFRM_MAX_MTU ETH_DATA_LEN
 
 /* Min/Max frame lengths */
-#define QCAFRM_ETHMINLEN (QCAFRM_ETHMINMTU + ETH_HLEN)
-#define QCAFRM_ETHMAXLEN (QCAFRM_ETHMAXMTU + VLAN_ETH_HLEN)
+#define QCAFRM_MIN_LEN (QCAFRM_MIN_MTU + ETH_HLEN)
+#define QCAFRM_MAX_LEN (QCAFRM_MAX_MTU + VLAN_ETH_HLEN)
 
 /* QCA7K header len */
 #define QCAFRM_HEADER_LEN 8
@@ -61,6 +61,7 @@
 #define QCAFRM_ERR_BASE -1000
 
 enum qcafrm_state {
+	/* HW length is only available on SPI */
 	QCAFRM_HW_LEN0 = 0x8000,
 	QCAFRM_HW_LEN1 = QCAFRM_HW_LEN0 - 1,
 	QCAFRM_HW_LEN2 = QCAFRM_HW_LEN1 - 1,
@@ -101,9 +102,11 @@ enum qcafrm_state {
 struct qcafrm_handle {
 	/*  Current decoding state */
 	enum qcafrm_state state;
+	/* Initial state depends on connection type */
+	enum qcafrm_state init;
 
 	/* Offset in buffer (borrowed for length too) */
-	s16 offset;
+	u16 offset;
 
 	/* Frame length as kept by this module */
 	u16 len;
@@ -113,9 +116,16 @@ u16 qcafrm_create_header(u8 *buf, u16 len);
 
 u16 qcafrm_create_footer(u8 *buf);
 
-static inline void qcafrm_fsm_init(struct qcafrm_handle *handle)
+static inline void qcafrm_fsm_init_spi(struct qcafrm_handle *handle)
 {
-	handle->state = QCAFRM_HW_LEN0;
+	handle->init = QCAFRM_HW_LEN0;
+	handle->state = handle->init;
+}
+
+static inline void qcafrm_fsm_init_uart(struct qcafrm_handle *handle)
+{
+	handle->init = QCAFRM_WAIT_AA1;
+	handle->state = handle->init;
 }
 
 /*   Gather received bytes and try to extract a full Ethernet frame

drivers/net/ethernet/qualcomm/qca_debug.c

@@ -275,6 +275,7 @@ qcaspi_get_ringparam(struct net_device *dev, struct ethtool_ringparam *ring)
 static int
 qcaspi_set_ringparam(struct net_device *dev, struct ethtool_ringparam *ring)
 {
+	const struct net_device_ops *ops = dev->netdev_ops;
 	struct qcaspi *qca = netdev_priv(dev);
 
 	if ((ring->rx_pending) ||
@@ -283,13 +284,13 @@ qcaspi_set_ringparam(struct net_device *dev, struct ethtool_ringparam *ring)
 		return -EINVAL;
 
 	if (netif_running(dev))
-		qcaspi_netdev_close(dev);
+		ops->ndo_stop(dev);
 
 	qca->txr.count = max_t(u32, ring->tx_pending, TX_RING_MIN_LEN);
 	qca->txr.count = min_t(u16, qca->txr.count, TX_RING_MAX_LEN);
 
 	if (netif_running(dev))
-		qcaspi_netdev_open(dev);
+		ops->ndo_open(dev);
 
 	return 0;
 }

drivers/net/ethernet/qualcomm/qca_spi.c

@@ -43,8 +43,8 @@
 #include <linux/types.h>
 
 #include "qca_7k.h"
+#include "qca_7k_common.h"
 #include "qca_debug.h"
-#include "qca_framing.h"
 #include "qca_spi.h"
 
 #define MAX_DMA_BURST_LEN 5000
@@ -69,7 +69,6 @@ static int qcaspi_pluggable = QCASPI_PLUGGABLE_MIN;
 module_param(qcaspi_pluggable, int, 0);
 MODULE_PARM_DESC(qcaspi_pluggable, "Pluggable SPI connection (yes/no).");
 
-#define QCASPI_MTU QCAFRM_ETHMAXMTU
 #define QCASPI_TX_TIMEOUT (1 * HZ)
 #define QCASPI_QCA7K_REBOOT_TIME_MS 1000
 
@@ -192,6 +191,30 @@ qcaspi_read_legacy(struct qcaspi *qca, u8 *dst, u32 len)
 	return len;
 }
 
+static int
+qcaspi_tx_cmd(struct qcaspi *qca, u16 cmd)
+{
+	__be16 tx_data;
+	struct spi_message *msg = &qca->spi_msg1;
+	struct spi_transfer *transfer = &qca->spi_xfer1;
+	int ret;
+
+	tx_data = cpu_to_be16(cmd);
+	transfer->len = sizeof(tx_data);
+	transfer->tx_buf = &tx_data;
+	transfer->rx_buf = NULL;
+
+	ret = spi_sync(qca->spi_dev, msg);
+
+	if (!ret)
+		ret = msg->status;
+
+	if (ret)
+		qcaspi_spi_error(qca);
+
+	return ret;
+}
+
 static int
 qcaspi_tx_frame(struct qcaspi *qca, struct sk_buff *skb)
 {
@@ -403,7 +426,7 @@ qcaspi_tx_ring_has_space(struct tx_ring *txr)
 	if (txr->skb[txr->tail])
 		return 0;
 
-	return (txr->size + QCAFRM_ETHMAXLEN < QCASPI_HW_BUF_LEN) ? 1 : 0;
+	return (txr->size + QCAFRM_MAX_LEN < QCASPI_HW_BUF_LEN) ? 1 : 0;
 }
 
 /*   Flush the tx ring. This function is only safe to
@@ -603,7 +626,7 @@ qcaspi_intr_handler(int irq, void *data)
 	return IRQ_HANDLED;
 }
 
-int
+static int
 qcaspi_netdev_open(struct net_device *dev)
 {
 	struct qcaspi *qca = netdev_priv(dev);
@@ -615,7 +638,7 @@ qcaspi_netdev_open(struct net_device *dev)
 	qca->intr_req = 1;
 	qca->intr_svc = 0;
 	qca->sync = QCASPI_SYNC_UNKNOWN;
-	qcafrm_fsm_init(&qca->frm_handle);
+	qcafrm_fsm_init_spi(&qca->frm_handle);
 
 	qca->spi_thread = kthread_run((void *)qcaspi_spi_thread,
 				      qca, "%s", dev->name);
@@ -640,7 +663,7 @@ qcaspi_netdev_open(struct net_device *dev)
 	return 0;
 }
 
-int
+static int
 qcaspi_netdev_close(struct net_device *dev)
 {
 	struct qcaspi *qca = netdev_priv(dev);
@@ -667,8 +690,8 @@ qcaspi_netdev_xmit(struct sk_buff *skb, struct net_device *dev)
 	struct sk_buff *tskb;
 	u8 pad_len = 0;
 
-	if (skb->len < QCAFRM_ETHMINLEN)
-		pad_len = QCAFRM_ETHMINLEN - skb->len;
+	if (skb->len < QCAFRM_MIN_LEN)
+		pad_len = QCAFRM_MIN_LEN - skb->len;
 
 	if (qca->txr.skb[qca->txr.tail]) {
 		netdev_warn(qca->net_dev, "queue was unexpectedly full!\n");
@@ -746,7 +769,7 @@ qcaspi_netdev_init(struct net_device *dev)
 {
 	struct qcaspi *qca = netdev_priv(dev);
 
-	dev->mtu = QCASPI_MTU;
+	dev->mtu = QCAFRM_MAX_MTU;
 	dev->type = ARPHRD_ETHER;
 	qca->clkspeed = qcaspi_clkspeed;
 	qca->burst_len = qcaspi_burst_len;
@@ -805,8 +828,8 @@ qcaspi_netdev_setup(struct net_device *dev)
 	dev->tx_queue_len = 100;
 
 	/* MTU range: 46 - 1500 */
-	dev->min_mtu = QCAFRM_ETHMINMTU;
-	dev->max_mtu = QCAFRM_ETHMAXMTU;
+	dev->min_mtu = QCAFRM_MIN_MTU;
+	dev->max_mtu = QCAFRM_MAX_MTU;
 
 	qca = netdev_priv(dev);
 	memset(qca, 0, sizeof(struct qcaspi));
@@ -894,6 +917,7 @@ qca_spi_probe(struct spi_device *spi)
 		return -ENOMEM;
 
 	qcaspi_netdev_setup(qcaspi_devs);
+	SET_NETDEV_DEV(qcaspi_devs, &spi->dev);
 
 	qca = netdev_priv(qcaspi_devs);
 	if (!qca) {
@@ -975,7 +999,7 @@ static struct spi_driver qca_spi_driver = {
 };
 module_spi_driver(qca_spi_driver);
 
-MODULE_DESCRIPTION("Qualcomm Atheros SPI Driver");
+MODULE_DESCRIPTION("Qualcomm Atheros QCA7000 SPI Driver");
 MODULE_AUTHOR("Qualcomm Atheros Communications");
 MODULE_AUTHOR("Stefan Wahren <stefan.wahren@i2se.com>");
 MODULE_LICENSE("Dual BSD/GPL");

drivers/net/ethernet/qualcomm/qca_spi.h

@@ -32,7 +32,7 @@
 #include <linux/spi/spi.h>
 #include <linux/types.h>
 
-#include "qca_framing.h"
+#include "qca_7k_common.h"
 
 #define QCASPI_DRV_VERSION "0.2.7-i"
 #define QCASPI_DRV_NAME    "qcaspi"
@@ -108,7 +108,4 @@ struct qcaspi {
 	u16 burst_len;
 };
 
-int qcaspi_netdev_open(struct net_device *dev);
-int qcaspi_netdev_close(struct net_device *dev);
-
 #endif /* _QCA_SPI_H */

drivers/net/ethernet/qualcomm/qca_uart.c

+/*
+ *   Copyright (c) 2011, 2012, Qualcomm Atheros Communications Inc.
+ *   Copyright (c) 2017, I2SE GmbH
+ *
+ *   Permission to use, copy, modify, and/or distribute this software
+ *   for any purpose with or without fee is hereby granted, provided
+ *   that the above copyright notice and this permission notice appear
+ *   in all copies.
+ *
+ *   THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
+ *   WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
+ *   WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL
+ *   THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR
+ *   CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
+ *   LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,
+ *   NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN
+ *   CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+/*   This module implements the Qualcomm Atheros UART protocol for
+ *   kernel-based UART device; it is essentially an Ethernet-to-UART
+ *   serial converter;
+ */
+
+#include <linux/device.h>
+#include <linux/errno.h>
+#include <linux/etherdevice.h>
+#include <linux/if_arp.h>
+#include <linux/if_ether.h>
+#include <linux/jiffies.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_net.h>
+#include <linux/sched.h>
+#include <linux/serdev.h>
+#include <linux/skbuff.h>
+#include <linux/types.h>
+
+#include "qca_7k_common.h"
+
+#define QCAUART_DRV_VERSION "0.1.0"
+#define QCAUART_DRV_NAME "qcauart"
+#define QCAUART_TX_TIMEOUT (1 * HZ)
+
+struct qcauart {
+	struct net_device *net_dev;
+	spinlock_t lock;			/* transmit lock */
+	struct work_struct tx_work;		/* Flushes transmit buffer   */
+
+	struct serdev_device *serdev;
+	struct qcafrm_handle frm_handle;
+	struct sk_buff *rx_skb;
+
+	unsigned char *tx_head;			/* pointer to next XMIT byte */
+	int tx_left;				/* bytes left in XMIT queue  */
+	unsigned char *tx_buffer;
+};
+
+static int
+qca_tty_receive(struct serdev_device *serdev, const unsigned char *data,
+		size_t count)
+{
+	struct qcauart *qca = serdev_device_get_drvdata(serdev);
+	struct net_device *netdev = qca->net_dev;
+	struct net_device_stats *n_stats = &netdev->stats;
+	size_t i;
+
+	if (!qca->rx_skb) {
+		qca->rx_skb = netdev_alloc_skb_ip_align(netdev,
+							netdev->mtu +
+							VLAN_ETH_HLEN);
+		if (!qca->rx_skb) {
+			n_stats->rx_errors++;
+			n_stats->rx_dropped++;
+			return 0;
+		}
+	}
+
+	for (i = 0; i < count; i++) {
+		s32 retcode;
+
+		retcode = qcafrm_fsm_decode(&qca->frm_handle,
+					    qca->rx_skb->data,
+					    skb_tailroom(qca->rx_skb),
+					    data[i]);
+
+		switch (retcode) {
+		case QCAFRM_GATHER:
+		case QCAFRM_NOHEAD:
+			break;
+		case QCAFRM_NOTAIL:
+			netdev_dbg(netdev, "recv: no RX tail\n");
+			n_stats->rx_errors++;
+			n_stats->rx_dropped++;
+			break;
+		case QCAFRM_INVLEN:
+			netdev_dbg(netdev, "recv: invalid RX length\n");
+			n_stats->rx_errors++;
+			n_stats->rx_dropped++;
+			break;
+		default:
+			n_stats->rx_packets++;
+			n_stats->rx_bytes += retcode;
+			skb_put(qca->rx_skb, retcode);
+			qca->rx_skb->protocol = eth_type_trans(
+						qca->rx_skb, qca->rx_skb->dev);
+			qca->rx_skb->ip_summed = CHECKSUM_UNNECESSARY;
+			netif_rx_ni(qca->rx_skb);
+			qca->rx_skb = netdev_alloc_skb_ip_align(netdev,
+								netdev->mtu +
+								VLAN_ETH_HLEN);
+			if (!qca->rx_skb) {
+				netdev_dbg(netdev, "recv: out of RX resources\n");
+				n_stats->rx_errors++;
+				return i;
+			}
+		}
+	}
+
+	return i;
+}
+
+/* Write out any remaining transmit buffer. Scheduled when tty is writable */
+static void qcauart_transmit(struct work_struct *work)
+{
+	struct qcauart *qca = container_of(work, struct qcauart, tx_work);
+	struct net_device_stats *n_stats = &qca->net_dev->stats;
+	int written;
+
+	spin_lock_bh(&qca->lock);
+
+	/* First make sure we're connected. */
+	if (!netif_running(qca->net_dev)) {
+		spin_unlock_bh(&qca->lock);
+		return;
+	}
+
+	if (qca->tx_left <= 0)  {
+		/* Now serial buffer is almost free & we can start
+		 * transmission of another packet
+		 */
+		n_stats->tx_packets++;
+		spin_unlock_bh(&qca->lock);
+		netif_wake_queue(qca->net_dev);
+		return;
+	}
+
+	written = serdev_device_write_buf(qca->serdev, qca->tx_head,
+					  qca->tx_left);
+	if (written > 0) {
+		qca->tx_left -= written;
+		qca->tx_head += written;
+	}
+	spin_unlock_bh(&qca->lock);
+}
+
+/* Called by the driver when there's room for more data.
+ * Schedule the transmit.
+ */
+static void qca_tty_wakeup(struct serdev_device *serdev)
+{
+	struct qcauart *qca = serdev_device_get_drvdata(serdev);
+
+	schedule_work(&qca->tx_work);
+}
+
+static struct serdev_device_ops qca_serdev_ops = {
+	.receive_buf = qca_tty_receive,
+	.write_wakeup = qca_tty_wakeup,
+};
+
+static int qcauart_netdev_open(struct net_device *dev)
+{
+	struct qcauart *qca = netdev_priv(dev);
+
+	netif_start_queue(qca->net_dev);
+
+	return 0;
+}
+
+static int qcauart_netdev_close(struct net_device *dev)
+{
+	struct qcauart *qca = netdev_priv(dev);
+
+	netif_stop_queue(dev);
+	flush_work(&qca->tx_work);
+
+	spin_lock_bh(&qca->lock);
+	qca->tx_left = 0;
+	spin_unlock_bh(&qca->lock);
+
+	return 0;
+}
+
+static netdev_tx_t
+qcauart_netdev_xmit(struct sk_buff *skb, struct net_device *dev)
+{
+	struct net_device_stats *n_stats = &dev->stats;
+	struct qcauart *qca = netdev_priv(dev);
+	u8 pad_len = 0;
+	int written;
+	u8 *pos;
+
+	spin_lock(&qca->lock);
+
+	WARN_ON(qca->tx_left);
+
+	if (!netif_running(dev))  {
+		spin_unlock(&qca->lock);
+		netdev_warn(qca->net_dev, "xmit: iface is down\n");
+		goto out;
+	}
+
+	pos = qca->tx_buffer;
+
+	if (skb->len < QCAFRM_MIN_LEN)
+		pad_len = QCAFRM_MIN_LEN - skb->len;
+
+	pos += qcafrm_create_header(pos, skb->len + pad_len);
+
+	memcpy(pos, skb->data, skb->len);
+	pos += skb->len;
+
+	if (pad_len) {
+		memset(pos, 0, pad_len);
+		pos += pad_len;
+	}
+
+	pos += qcafrm_create_footer(pos);
+
+	netif_stop_queue(qca->net_dev);
+
+	written = serdev_device_write_buf(qca->serdev, qca->tx_buffer,
+					  pos - qca->tx_buffer);
+	if (written > 0) {
+		qca->tx_left = (pos - qca->tx_buffer) - written;
+		qca->tx_head = qca->tx_buffer + written;
+		n_stats->tx_bytes += written;
+	}
+	spin_unlock(&qca->lock);
+
+	netif_trans_update(dev);
+out:
+	dev_kfree_skb_any(skb);
+	return NETDEV_TX_OK;
+}
+
+static void qcauart_netdev_tx_timeout(struct net_device *dev)
+{
+	struct qcauart *qca = netdev_priv(dev);
+
+	netdev_info(qca->net_dev, "Transmit timeout at %ld, latency %ld\n",
+		    jiffies, dev_trans_start(dev));
+	dev->stats.tx_errors++;
+	dev->stats.tx_dropped++;
+}
+
+static int qcauart_netdev_init(struct net_device *dev)
+{
+	struct qcauart *qca = netdev_priv(dev);
+	size_t len;
+
+	/* Finish setting up the device info. */
+	dev->mtu = QCAFRM_MAX_MTU;
+	dev->type = ARPHRD_ETHER;
+
+	len = QCAFRM_HEADER_LEN + QCAFRM_MAX_LEN + QCAFRM_FOOTER_LEN;
+	qca->tx_buffer = devm_kmalloc(&qca->serdev->dev, len, GFP_KERNEL);
+	if (!qca->tx_buffer)
+		return -ENOMEM;
+
+	qca->rx_skb = netdev_alloc_skb_ip_align(qca->net_dev,
+						qca->net_dev->mtu +
+						VLAN_ETH_HLEN);
+	if (!qca->rx_skb)
+		return -ENOBUFS;
+
+	return 0;
+}
+
+static void qcauart_netdev_uninit(struct net_device *dev)
+{
+	struct qcauart *qca = netdev_priv(dev);
+
+	if (qca->rx_skb)
+		dev_kfree_skb(qca->rx_skb);
+}
+
+static const struct net_device_ops qcauart_netdev_ops = {
+	.ndo_init = qcauart_netdev_init,
+	.ndo_uninit = qcauart_netdev_uninit,
+	.ndo_open = qcauart_netdev_open,
+	.ndo_stop = qcauart_netdev_close,
+	.ndo_start_xmit = qcauart_netdev_xmit,
+	.ndo_set_mac_address = eth_mac_addr,
+	.ndo_tx_timeout = qcauart_netdev_tx_timeout,
+	.ndo_validate_addr = eth_validate_addr,
+};
+
+static void qcauart_netdev_setup(struct net_device *dev)
+{
+	dev->netdev_ops = &qcauart_netdev_ops;
+	dev->watchdog_timeo = QCAUART_TX_TIMEOUT;
+	dev->priv_flags &= ~IFF_TX_SKB_SHARING;
+	dev->tx_queue_len = 100;
+
+	/* MTU range: 46 - 1500 */
+	dev->min_mtu = QCAFRM_MIN_MTU;
+	dev->max_mtu = QCAFRM_MAX_MTU;
+}
+
+static const struct of_device_id qca_uart_of_match[] = {
+	{
+	 .compatible = "qca,qca7000",
+	},
+	{}
+};
+MODULE_DEVICE_TABLE(of, qca_uart_of_match);
+
+static int qca_uart_probe(struct serdev_device *serdev)
+{
+	struct net_device *qcauart_dev = alloc_etherdev(sizeof(struct qcauart));
+	struct qcauart *qca;
+	const char *mac;
+	u32 speed = 115200;
+	int ret;
+
+	if (!qcauart_dev)
+		return -ENOMEM;
+
+	qcauart_netdev_setup(qcauart_dev);
+	SET_NETDEV_DEV(qcauart_dev, &serdev->dev);
+
+	qca = netdev_priv(qcauart_dev);
+	if (!qca) {
+		pr_err("qca_uart: Fail to retrieve private structure\n");
+		ret = -ENOMEM;
+		goto free;
+	}
+	qca->net_dev = qcauart_dev;
+	qca->serdev = serdev;
+	qcafrm_fsm_init_uart(&qca->frm_handle);
+
+	spin_lock_init(&qca->lock);
+	INIT_WORK(&qca->tx_work, qcauart_transmit);
+
+	of_property_read_u32(serdev->dev.of_node, "current-speed", &speed);
+
+	mac = of_get_mac_address(serdev->dev.of_node);
+
+	if (mac)
+		ether_addr_copy(qca->net_dev->dev_addr, mac);
+
+	if (!is_valid_ether_addr(qca->net_dev->dev_addr)) {
+		eth_hw_addr_random(qca->net_dev);
+		dev_info(&serdev->dev, "Using random MAC address: %pM\n",
+			 qca->net_dev->dev_addr);
+	}
+
+	netif_carrier_on(qca->net_dev);
+	serdev_device_set_drvdata(serdev, qca);
+	serdev_device_set_client_ops(serdev, &qca_serdev_ops);
+
+	ret = serdev_device_open(serdev);
+	if (ret) {
+		dev_err(&serdev->dev, "Unable to open device %s\n",
+			qcauart_dev->name);
+		goto free;
+	}
+
+	speed = serdev_device_set_baudrate(serdev, speed);
+	dev_info(&serdev->dev, "Using baudrate: %u\n", speed);
+
+	serdev_device_set_flow_control(serdev, false);
+
+	ret = register_netdev(qcauart_dev);
+	if (ret) {
+		dev_err(&serdev->dev, "Unable to register net device %s\n",
+			qcauart_dev->name);
+		serdev_device_close(serdev);
+		cancel_work_sync(&qca->tx_work);
+		goto free;
+	}
+
+	return 0;
+
+free:
+	free_netdev(qcauart_dev);
+	return ret;
+}
+
+static void qca_uart_remove(struct serdev_device *serdev)
+{
+	struct qcauart *qca = serdev_device_get_drvdata(serdev);
+
+	unregister_netdev(qca->net_dev);
+
+	/* Flush any pending characters in the driver. */
+	serdev_device_close(serdev);
+	cancel_work_sync(&qca->tx_work);
+
+	free_netdev(qca->net_dev);
+}
+
+static struct serdev_device_driver qca_uart_driver = {
+	.probe = qca_uart_probe,
+	.remove = qca_uart_remove,
+	.driver = {
+		.name = QCAUART_DRV_NAME,
+		.of_match_table = of_match_ptr(qca_uart_of_match),
+	},
+};
+
+module_serdev_device_driver(qca_uart_driver);
+
+MODULE_DESCRIPTION("Qualcomm Atheros QCA7000 UART Driver");
+MODULE_AUTHOR("Qualcomm Atheros Communications");
+MODULE_AUTHOR("Stefan Wahren <stefan.wahren@i2se.com>");
+MODULE_LICENSE("Dual BSD/GPL");
+MODULE_VERSION(QCAUART_DRV_VERSION);