Merge branch 'x86/apic' into cpus4096

This done for conflict prevention: we merge it into the cpus4096 tree
because upcoming cpumask changes will touch apic.c that would collide
with x86/apic otherwise.

arch/x86/kernel/apic.c

@@ -441,6 +441,7 @@ static void lapic_timer_setup(enum clock_event_mode mode,
 		v = apic_read(APIC_LVTT);
 		v |= (APIC_LVT_MASKED | LOCAL_TIMER_VECTOR);
 		apic_write(APIC_LVTT, v);
+		apic_write(APIC_TMICT, 0xffffffff);
 		break;
 	case CLOCK_EVT_MODE_RESUME:
 		/* Nothing to do here */
@@ -559,13 +560,13 @@ static int __init calibrate_by_pmtimer(long deltapm, long *delta)
 	} else {
 		res = (((u64)deltapm) *  mult) >> 22;
 		do_div(res, 1000000);
-		printk(KERN_WARNING "APIC calibration not consistent "
+		pr_warning("APIC calibration not consistent "
 			"with PM Timer: %ldms instead of 100ms\n",
 			(long)res);
 		/* Correct the lapic counter value */
 		res = (((u64)(*delta)) * pm_100ms);
 		do_div(res, deltapm);
-		printk(KERN_INFO "APIC delta adjusted to PM-Timer: "
+		pr_info("APIC delta adjusted to PM-Timer: "
 			"%lu (%ld)\n", (unsigned long)res, *delta);
 		*delta = (long)res;
 	}
@@ -645,8 +646,7 @@ static int __init calibrate_APIC_clock(void)
 	 */
 	if (calibration_result < (1000000 / HZ)) {
 		local_irq_enable();
-		printk(KERN_WARNING
-		       "APIC frequency too slow, disabling apic timer\n");
+		pr_warning("APIC frequency too slow, disabling apic timer\n");
 		return -1;
 	}
 
@@ -672,13 +672,9 @@ static int __init calibrate_APIC_clock(void)
 		while (lapic_cal_loops <= LAPIC_CAL_LOOPS)
 			cpu_relax();
 
-		local_irq_disable();
-
 		/* Stop the lapic timer */
 		lapic_timer_setup(CLOCK_EVT_MODE_SHUTDOWN, levt);
 
-		local_irq_enable();
-
 		/* Jiffies delta */
 		deltaj = lapic_cal_j2 - lapic_cal_j1;
 		apic_printk(APIC_VERBOSE, "... jiffies delta = %lu\n", deltaj);
@@ -692,8 +688,7 @@ static int __init calibrate_APIC_clock(void)
 		local_irq_enable();
 
 	if (levt->features & CLOCK_EVT_FEAT_DUMMY) {
-		printk(KERN_WARNING
-		       "APIC timer disabled due to verification failure.\n");
+		pr_warning("APIC timer disabled due to verification failure.\n");
 			return -1;
 	}
 
@@ -714,7 +709,7 @@ void __init setup_boot_APIC_clock(void)
 	 * broadcast mechanism is used. On UP systems simply ignore it.
 	 */
 	if (disable_apic_timer) {
-		printk(KERN_INFO "Disabling APIC timer\n");
+		pr_info("Disabling APIC timer\n");
 		/* No broadcast on UP ! */
 		if (num_possible_cpus() > 1) {
 			lapic_clockevent.mult = 1;
@@ -741,7 +736,7 @@ void __init setup_boot_APIC_clock(void)
 	if (nmi_watchdog != NMI_IO_APIC)
 		lapic_clockevent.features &= ~CLOCK_EVT_FEAT_DUMMY;
 	else
-		printk(KERN_WARNING "APIC timer registered as dummy,"
+		pr_warning("APIC timer registered as dummy,"
 			" due to nmi_watchdog=%d!\n", nmi_watchdog);
 
 	/* Setup the lapic or request the broadcast */
@@ -773,8 +768,7 @@ static void local_apic_timer_interrupt(void)
 	 * spurious.
 	 */
 	if (!evt->event_handler) {
-		printk(KERN_WARNING
-		       "Spurious LAPIC timer interrupt on cpu %d\n", cpu);
+		pr_warning("Spurious LAPIC timer interrupt on cpu %d\n", cpu);
 		/* Switch it off */
 		lapic_timer_setup(CLOCK_EVT_MODE_SHUTDOWN, evt);
 		return;
@@ -1093,7 +1087,7 @@ static void __cpuinit lapic_setup_esr(void)
 	unsigned int oldvalue, value, maxlvt;
 
 	if (!lapic_is_integrated()) {
-		printk(KERN_INFO "No ESR for 82489DX.\n");
+		pr_info("No ESR for 82489DX.\n");
 		return;
 	}
 
@@ -1104,7 +1098,7 @@ static void __cpuinit lapic_setup_esr(void)
 		 * ESR disabled - we can't do anything useful with the
 		 * errors anyway - mbligh
 		 */
-		printk(KERN_INFO "Leaving ESR disabled.\n");
+		pr_info("Leaving ESR disabled.\n");
 		return;
 	}
 
@@ -1298,7 +1292,7 @@ void check_x2apic(void)
 	rdmsr(MSR_IA32_APICBASE, msr, msr2);
 
 	if (msr & X2APIC_ENABLE) {
-		printk("x2apic enabled by BIOS, switching to x2apic ops\n");
+		pr_info("x2apic enabled by BIOS, switching to x2apic ops\n");
 		x2apic_preenabled = x2apic = 1;
 		apic_ops = &x2apic_ops;
 	}
@@ -1310,7 +1304,7 @@ void enable_x2apic(void)
 
 	rdmsr(MSR_IA32_APICBASE, msr, msr2);
 	if (!(msr & X2APIC_ENABLE)) {
-		printk("Enabling x2apic\n");
+		pr_info("Enabling x2apic\n");
 		wrmsr(MSR_IA32_APICBASE, msr | X2APIC_ENABLE, 0);
 	}
 }
@@ -1325,8 +1319,7 @@ void __init enable_IR_x2apic(void)
 		return;
 
 	if (!x2apic_preenabled && disable_x2apic) {
-		printk(KERN_INFO
-		       "Skipped enabling x2apic and Interrupt-remapping "
+		pr_info("Skipped enabling x2apic and Interrupt-remapping "
 			"because of nox2apic\n");
 		return;
 	}
@@ -1335,22 +1328,19 @@ void __init enable_IR_x2apic(void)
 		panic("Bios already enabled x2apic, can't enforce nox2apic");
 
 	if (!x2apic_preenabled && skip_ioapic_setup) {
-		printk(KERN_INFO
-		       "Skipped enabling x2apic and Interrupt-remapping "
+		pr_info("Skipped enabling x2apic and Interrupt-remapping "
 			"because of skipping io-apic setup\n");
 		return;
 	}
 
 	ret = dmar_table_init();
 	if (ret) {
-		printk(KERN_INFO
-		       "dmar_table_init() failed with %d:\n", ret);
+		pr_info("dmar_table_init() failed with %d:\n", ret);
 
 		if (x2apic_preenabled)
 			panic("x2apic enabled by bios. But IR enabling failed");
 		else
-			printk(KERN_INFO
-			       "Not enabling x2apic,Intr-remapping\n");
+			pr_info("Not enabling x2apic,Intr-remapping\n");
 		return;
 	}
 
@@ -1359,7 +1349,7 @@ void __init enable_IR_x2apic(void)
 
 	ret = save_mask_IO_APIC_setup();
 	if (ret) {
-		printk(KERN_INFO "Saving IO-APIC state failed: %d\n", ret);
+		pr_info("Saving IO-APIC state failed: %d\n", ret);
 		goto end;
 	}
 
@@ -1394,14 +1384,11 @@ void __init enable_IR_x2apic(void)
 
 	if (!ret) {
 		if (!x2apic_preenabled)
-			printk(KERN_INFO
-			       "Enabled x2apic and interrupt-remapping\n");
+			pr_info("Enabled x2apic and interrupt-remapping\n");
 		else
-			printk(KERN_INFO
-			       "Enabled Interrupt-remapping\n");
+			pr_info("Enabled Interrupt-remapping\n");
 	} else
-		printk(KERN_ERR
-		       "Failed to enable Interrupt-remapping and x2apic\n");
+		pr_err("Failed to enable Interrupt-remapping and x2apic\n");
 #else
 	if (!cpu_has_x2apic)
 		return;
@@ -1410,7 +1397,7 @@ void __init enable_IR_x2apic(void)
 		panic("x2apic enabled prior OS handover,"
 		      " enable CONFIG_INTR_REMAP");
 
-	printk(KERN_INFO "Enable CONFIG_INTR_REMAP for enabling intr-remapping "
+	pr_info("Enable CONFIG_INTR_REMAP for enabling intr-remapping "
 		" and x2apic\n");
 #endif
 
@@ -1428,7 +1415,7 @@ void __init enable_IR_x2apic(void)
 static int __init detect_init_APIC(void)
 {
 	if (!cpu_has_apic) {
-		printk(KERN_INFO "No local APIC present\n");
+		pr_info("No local APIC present\n");
 		return -1;
 	}
 
@@ -1469,7 +1456,7 @@ static int __init detect_init_APIC(void)
 		 * "lapic" specified.
 		 */
 		if (!force_enable_local_apic) {
-			printk(KERN_INFO "Local APIC disabled by BIOS -- "
+			pr_info("Local APIC disabled by BIOS -- "
 				"you can enable it with \"lapic\"\n");
 			return -1;
 		}
@@ -1480,8 +1467,7 @@ static int __init detect_init_APIC(void)
 		 */
 		rdmsr(MSR_IA32_APICBASE, l, h);
 		if (!(l & MSR_IA32_APICBASE_ENABLE)) {
-			printk(KERN_INFO
-			       "Local APIC disabled by BIOS -- reenabling.\n");
+			pr_info("Local APIC disabled by BIOS -- reenabling.\n");
 			l &= ~MSR_IA32_APICBASE_BASE;
 			l |= MSR_IA32_APICBASE_ENABLE | APIC_DEFAULT_PHYS_BASE;
 			wrmsr(MSR_IA32_APICBASE, l, h);
@@ -1494,7 +1480,7 @@ static int __init detect_init_APIC(void)
 	 */
 	features = cpuid_edx(1);
 	if (!(features & (1 << X86_FEATURE_APIC))) {
-		printk(KERN_WARNING "Could not enable APIC!\n");
+		pr_warning("Could not enable APIC!\n");
 		return -1;
 	}
 	set_cpu_cap(&boot_cpu_data, X86_FEATURE_APIC);
@@ -1505,14 +1491,14 @@ static int __init detect_init_APIC(void)
 	if (l & MSR_IA32_APICBASE_ENABLE)
 		mp_lapic_addr = l & MSR_IA32_APICBASE_BASE;
 
-	printk(KERN_INFO "Found and enabled local APIC!\n");
+	pr_info("Found and enabled local APIC!\n");
 
 	apic_pm_activate();
 
 	return 0;
 
 no_apic:
-	printk(KERN_INFO "No local APIC present or hardware disabled\n");
+	pr_info("No local APIC present or hardware disabled\n");
 	return -1;
 }
 #endif
@@ -1588,12 +1574,12 @@ int __init APIC_init_uniprocessor(void)
 {
 #ifdef CONFIG_X86_64
 	if (disable_apic) {
-		printk(KERN_INFO "Apic disabled\n");
+		pr_info("Apic disabled\n");
 		return -1;
 	}
 	if (!cpu_has_apic) {
 		disable_apic = 1;
-		printk(KERN_INFO "Apic disabled by BIOS\n");
+		pr_info("Apic disabled by BIOS\n");
 		return -1;
 	}
 #else
@@ -1605,7 +1591,7 @@ int __init APIC_init_uniprocessor(void)
 	 */
 	if (!cpu_has_apic &&
 	    APIC_INTEGRATED(apic_version[boot_cpu_physical_apicid])) {
-		printk(KERN_ERR "BIOS bug, local APIC 0x%x not detected!...\n",
+		pr_err("BIOS bug, local APIC 0x%x not detected!...\n",
 			boot_cpu_physical_apicid);
 		clear_cpu_cap(&boot_cpu_data, X86_FEATURE_APIC);
 		return -1;
@@ -1699,7 +1685,7 @@ void smp_spurious_interrupt(struct pt_regs *regs)
 	add_pda(irq_spurious_count, 1);
 #else
 	/* see sw-dev-man vol 3, chapter 7.4.13.5 */
-	printk(KERN_INFO "spurious APIC interrupt on CPU#%d, "
+	pr_info("spurious APIC interrupt on CPU#%d, "
 		"should never happen.\n", smp_processor_id());
 	__get_cpu_var(irq_stat).irq_spurious_count++;
 #endif
@@ -1724,17 +1710,18 @@ void smp_error_interrupt(struct pt_regs *regs)
 	ack_APIC_irq();
 	atomic_inc(&irq_err_count);
 
-	/* Here is what the APIC error bits mean:
-	   0: Send CS error
-	   1: Receive CS error
-	   2: Send accept error
-	   3: Receive accept error
-	   4: Reserved
-	   5: Send illegal vector
-	   6: Received illegal vector
-	   7: Illegal register address
-	*/
-	printk(KERN_DEBUG "APIC error on CPU%d: %02x(%02x)\n",
+	/*
+	 * Here is what the APIC error bits mean:
+	 * 0: Send CS error
+	 * 1: Receive CS error
+	 * 2: Send accept error
+	 * 3: Receive accept error
+	 * 4: Reserved
+	 * 5: Send illegal vector
+	 * 6: Received illegal vector
+	 * 7: Illegal register address
+	 */
+	pr_debug("APIC error on CPU%d: %02x(%02x)\n",
 		smp_processor_id(), v , v1);
 	irq_exit();
 }
@@ -1838,7 +1825,7 @@ void __cpuinit generic_processor_info(int apicid, int version)
 	 * Validate version
 	 */
 	if (version == 0x0) {
-		printk(KERN_WARNING "BIOS bug, APIC version is 0 for CPU#%d! "
+		pr_warning("BIOS bug, APIC version is 0 for CPU#%d! "
 			"fixing up to 0x10. (tell your hw vendor)\n",
 			version);
 		version = 0x10;
@@ -1846,7 +1833,7 @@ void __cpuinit generic_processor_info(int apicid, int version)
 	apic_version[apicid] = version;
 
 	if (num_processors >= NR_CPUS) {
-		printk(KERN_WARNING "WARNING: NR_CPUS limit of %i reached."
+		pr_warning("WARNING: NR_CPUS limit of %i reached."
 			"  Processor ignored.\n", NR_CPUS);
 		return;
 	}
@@ -2209,7 +2196,7 @@ static int __init apic_set_verbosity(char *arg)
 	else if (strcmp("verbose", arg) == 0)
 		apic_verbosity = APIC_VERBOSE;
 	else {
-		printk(KERN_WARNING "APIC Verbosity level %s not recognised"
+		pr_warning("APIC Verbosity level %s not recognised"
 			" use apic=verbose or apic=debug\n", arg);
 		return -EINVAL;
 	}

arch/x86/kernel/nmi.c

@@ -131,6 +131,11 @@ static void report_broken_nmi(int cpu, int *prev_nmi_count)
 	atomic_dec(&nmi_active);
 }
 
+static void __acpi_nmi_disable(void *__unused)
+{
+	apic_write(APIC_LVT0, APIC_DM_NMI | APIC_LVT_MASKED);
+}
+
 int __init check_nmi_watchdog(void)
 {
 	unsigned int *prev_nmi_count;
@@ -179,8 +184,12 @@ int __init check_nmi_watchdog(void)
 	kfree(prev_nmi_count);
 	return 0;
 error:
-	if (nmi_watchdog == NMI_IO_APIC && !timer_through_8259)
+	if (nmi_watchdog == NMI_IO_APIC) {
+		if (!timer_through_8259)
 			disable_8259A_irq(0);
+		on_each_cpu(__acpi_nmi_disable, NULL, 1);
+	}
+
 #ifdef CONFIG_X86_32
 	timer_ack = 0;
 #endif
@@ -285,11 +294,6 @@ void acpi_nmi_enable(void)
 		on_each_cpu(__acpi_nmi_enable, NULL, 1);
 }
 
-static void __acpi_nmi_disable(void *__unused)
-{
-	apic_write(APIC_LVT0, APIC_DM_NMI | APIC_LVT_MASKED);
-}
-
 /*
  * Disable timer based NMIs on all CPUs:
  */
@@ -340,6 +344,8 @@ void stop_apic_nmi_watchdog(void *unused)
 		return;
 	if (nmi_watchdog == NMI_LOCAL_APIC)
 		lapic_watchdog_stop();
+	else
+		__acpi_nmi_disable(NULL);
 	__get_cpu_var(wd_enabled) = 0;
 	atomic_dec(&nmi_active);
 }
@@ -465,6 +471,24 @@ nmi_watchdog_tick(struct pt_regs *regs, unsigned reason)
 
 #ifdef CONFIG_SYSCTL
 
+static void enable_ioapic_nmi_watchdog_single(void *unused)
+{
+	__get_cpu_var(wd_enabled) = 1;
+	atomic_inc(&nmi_active);
+	__acpi_nmi_enable(NULL);
+}
+
+static void enable_ioapic_nmi_watchdog(void)
+{
+	on_each_cpu(enable_ioapic_nmi_watchdog_single, NULL, 1);
+	touch_nmi_watchdog();
+}
+
+static void disable_ioapic_nmi_watchdog(void)
+{
+	on_each_cpu(stop_apic_nmi_watchdog, NULL, 1);
+}
+
 static int __init setup_unknown_nmi_panic(char *str)
 {
 	unknown_nmi_panic = 1;
@@ -507,6 +531,11 @@ int proc_nmi_enabled(struct ctl_table *table, int write, struct file *file,
 			enable_lapic_nmi_watchdog();
 		else
 			disable_lapic_nmi_watchdog();
+	} else if (nmi_watchdog == NMI_IO_APIC) {
+		if (nmi_watchdog_enabled)
+			enable_ioapic_nmi_watchdog();
+		else
+			disable_ioapic_nmi_watchdog();
 	} else {
 		printk(KERN_WARNING
 			"NMI watchdog doesn't know what hardware to touch\n");