Commit 9c4df53b authored by Ben Hutchings's avatar Ben Hutchings Committed by David S. Miller

ethtool, mdio, mii: Specify MDIO information fields in struct ethtool_cmd

Add comments for ethtool_cmd::phy_address and
ethtool_cmd::mdio_support, and definitions of the flags currently
used in mdio_support.

In the mdio library, assert that its own flags continue to match those
in the ethtool interface.

In the mii library, use the ethtool flag definition and stop
including <linux/mdio.h>.
Signed-off-by: default avatarBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 9c717758
......@@ -190,6 +190,9 @@ void mdio45_ethtool_gset_npage(const struct mdio_if_info *mdio,
int reg;
u32 speed;
BUILD_BUG_ON(MDIO_SUPPORTS_C22 != ETH_MDIO_SUPPORTS_C22);
BUILD_BUG_ON(MDIO_SUPPORTS_C45 != ETH_MDIO_SUPPORTS_C45);
ecmd->transceiver = XCVR_INTERNAL;
ecmd->phy_address = mdio->prtad;
ecmd->mdio_support =
......
......@@ -31,7 +31,7 @@
#include <linux/module.h>
#include <linux/netdevice.h>
#include <linux/ethtool.h>
#include <linux/mdio.h>
#include <linux/mii.h>
static u32 mii_get_an(struct mii_if_info *mii, u16 addr)
{
......@@ -74,7 +74,7 @@ int mii_ethtool_gset(struct mii_if_info *mii, struct ethtool_cmd *ecmd)
/* this isn't fully supported at higher layers */
ecmd->phy_address = mii->phy_id;
ecmd->mdio_support = MDIO_SUPPORTS_C22;
ecmd->mdio_support = ETH_MDIO_SUPPORTS_C22;
ecmd->advertising = ADVERTISED_TP | ADVERTISED_MII;
......
......@@ -30,10 +30,15 @@ struct ethtool_cmd {
* access it */
__u8 duplex; /* Duplex, half or full */
__u8 port; /* Which connector port */
__u8 phy_address;
__u8 phy_address; /* MDIO PHY address (PRTAD for clause 45).
* May be read-only or read-write
* depending on the driver.
*/
__u8 transceiver; /* Which transceiver to use */
__u8 autoneg; /* Enable or disable autonegotiation */
__u8 mdio_support;
__u8 mdio_support; /* MDIO protocols supported. Read-only.
* Not set by all drivers.
*/
__u32 maxtxpkt; /* Tx pkts before generating tx int */
__u32 maxrxpkt; /* Rx pkts before generating rx int */
__u16 speed_hi; /* The forced speed (upper
......@@ -59,6 +64,20 @@ static inline __u32 ethtool_cmd_speed(const struct ethtool_cmd *ep)
return (ep->speed_hi << 16) | ep->speed;
}
/* Device supports clause 22 register access to PHY or peripherals
* using the interface defined in <linux/mii.h>. This should not be
* set if there are known to be no such peripherals present or if
* the driver only emulates clause 22 registers for compatibility.
*/
#define ETH_MDIO_SUPPORTS_C22 1
/* Device supports clause 45 register access to PHY or peripherals
* using the interface defined in <linux/mii.h> and <linux/mdio.h>.
* This should not be set if there are known to be no such peripherals
* present.
*/
#define ETH_MDIO_SUPPORTS_C45 2
#define ETHTOOL_FWVERS_LEN 32
#define ETHTOOL_BUSINFO_LEN 32
/* these strings are set to whatever the driver author decides... */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment