sh: rts7751r2d board updates.

This tidies up some of the rts7751r2d mess and gets it booting
again. Update the defconfig, too.
Signed-off-by: Masayuki Hosokawa <hosokawa@ace-jp.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

arch/sh/boards/renesas/rts7751r2d/Makefile

@@ -2,4 +2,4 @@
 # Makefile for the RTS7751R2D specific parts of the kernel
 #
 
-obj-y	 := setup.o io.o irq.o
+obj-y	 := setup.o irq.o

arch/sh/boards/renesas/rts7751r2d/io.c

-/*
- * Copyright (C) 2001  Ian da Silva, Jeremy Siegel
- * Based largely on io_se.c.
- *
- * I/O routine for Renesas Technology sales RTS7751R2D.
- *
- * Initial version only to support LAN access; some
- * placeholder code from io_rts7751r2d.c left in with the
- * expectation of later SuperIO and PCMCIA access.
- */
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/io.h>
-#include <asm/rts7751r2d.h>
-#include <asm/addrspace.h>
-
-/*
- * The 7751R RTS7751R2D uses the built-in PCI controller (PCIC)
- * of the 7751R processor, and has a SuperIO accessible via the PCI.
- * The board also includes a PCMCIA controller on its memory bus,
- * like the other Solution Engine boards.
- */
-
-static inline unsigned long port2adr(unsigned int port)
-{
-	if ((0x1f0 <= port && port < 0x1f8) || port == 0x3f6)
-		if (port == 0x3f6)
-			return (PA_AREA5_IO + 0x80c);
-		else
-			return (PA_AREA5_IO + 0x1000 + ((port-0x1f0) << 1));
-	else
-		maybebadio((unsigned long)port);
-
-	return port;
-}
-
-static inline unsigned long port88796l(unsigned int port, int flag)
-{
-	unsigned long addr;
-
-	if (flag)
-		addr = PA_AX88796L + ((port - AX88796L_IO_BASE) << 1);
-	else
-		addr = PA_AX88796L + ((port - AX88796L_IO_BASE) << 1) + 0x1000;
-
-	return addr;
-}
-
-/* The 7751R RTS7751R2D seems to have everything hooked */
-/* up pretty normally (nothing on high-bytes only...) so this */
-/* shouldn't be needed */
-static inline int shifted_port(unsigned long port)
-{
-	/* For IDE registers, value is not shifted */
-	if ((0x1f0 <= port && port < 0x1f8) || port == 0x3f6)
-		return 0;
-	else
-		return 1;
-}
-
-#if defined(CONFIG_NE2000) || defined(CONFIG_NE2000_MODULE)
-#define CHECK_AX88796L_PORT(port) \
-  ((port >= AX88796L_IO_BASE) && (port < (AX88796L_IO_BASE+0x20)))
-#else
-#define CHECK_AX88796L_PORT(port) (0)
-#endif
-
-/*
- * General outline: remap really low stuff [eventually] to SuperIO,
- * stuff in PCI IO space (at or above window at pci.h:PCIBIOS_MIN_IO)
- * is mapped through the PCI IO window.  Stuff with high bits (PXSEG)
- * should be way beyond the window, and is used  w/o translation for
- * compatibility.
- */
-unsigned char rts7751r2d_inb(unsigned long port)
-{
-	if (CHECK_AX88796L_PORT(port))
-		return (*(volatile unsigned short *)port88796l(port, 0)) & 0xff;
-	else if (PXSEG(port))
-		return *(volatile unsigned char *)port;
-	else if (is_pci_ioaddr(port) || shifted_port(port))
-		return *(volatile unsigned char *)pci_ioaddr(port);
-	else
-		return (*(volatile unsigned short *)port2adr(port) & 0xff);
-}
-
-unsigned char rts7751r2d_inb_p(unsigned long port)
-{
-	unsigned char v;
-
-	if (CHECK_AX88796L_PORT(port))
-		v = (*(volatile unsigned short *)port88796l(port, 0)) & 0xff;
-        else if (PXSEG(port))
-		v = *(volatile unsigned char *)port;
-	else if (is_pci_ioaddr(port) || shifted_port(port))
-		v = *(volatile unsigned char *)pci_ioaddr(port);
-	else
-		v = (*(volatile unsigned short *)port2adr(port) & 0xff);
-
-	ctrl_delay();
-
-	return v;
-}
-
-unsigned short rts7751r2d_inw(unsigned long port)
-{
-	if (CHECK_AX88796L_PORT(port))
-		maybebadio(port);
-        else if (PXSEG(port))
-		return *(volatile unsigned short *)port;
-	else if (is_pci_ioaddr(port) || shifted_port(port))
-		return *(volatile unsigned short *)pci_ioaddr(port);
-	else
-		maybebadio(port);
-
-	return 0;
-}
-
-unsigned int rts7751r2d_inl(unsigned long port)
-{
-	if (CHECK_AX88796L_PORT(port))
-		maybebadio(port);
-        else if (PXSEG(port))
-		return *(volatile unsigned long *)port;
-	else if (is_pci_ioaddr(port) || shifted_port(port))
-		return *(volatile unsigned long *)pci_ioaddr(port);
-	else
-		maybebadio(port);
-
-	return 0;
-}
-
-void rts7751r2d_outb(unsigned char value, unsigned long port)
-{
-	if (CHECK_AX88796L_PORT(port))
-		*((volatile unsigned short *)port88796l(port, 0)) = value;
-        else if (PXSEG(port))
-		*(volatile unsigned char *)port = value;
-	else if (is_pci_ioaddr(port) || shifted_port(port))
-		*(volatile unsigned char *)pci_ioaddr(port) = value;
-	else
-		*(volatile unsigned short *)port2adr(port) = value;
-}
-
-void rts7751r2d_outb_p(unsigned char value, unsigned long port)
-{
-	if (CHECK_AX88796L_PORT(port))
-		*((volatile unsigned short *)port88796l(port, 0)) = value;
-        else if (PXSEG(port))
-		*(volatile unsigned char *)port = value;
-	else if (is_pci_ioaddr(port) || shifted_port(port))
-		*(volatile unsigned char *)pci_ioaddr(port) = value;
-	else
-		*(volatile unsigned short *)port2adr(port) = value;
-
-	ctrl_delay();
-}
-
-void rts7751r2d_outw(unsigned short value, unsigned long port)
-{
-	if (CHECK_AX88796L_PORT(port))
-		maybebadio(port);
-        else if (PXSEG(port))
-		*(volatile unsigned short *)port = value;
-	else if (is_pci_ioaddr(port) || shifted_port(port))
-		*(volatile unsigned short *)pci_ioaddr(port) = value;
-	else
-		maybebadio(port);
-}
-
-void rts7751r2d_outl(unsigned int value, unsigned long port)
-{
-	if (CHECK_AX88796L_PORT(port))
-		maybebadio(port);
-        else if (PXSEG(port))
-		*(volatile unsigned long *)port = value;
-	else if (is_pci_ioaddr(port) || shifted_port(port))
-		*(volatile unsigned long *)pci_ioaddr(port) = value;
-	else
-		maybebadio(port);
-}
-
-void rts7751r2d_insb(unsigned long port, void *addr, unsigned long count)
-{
-	unsigned long a = (unsigned long)addr;
-	volatile __u8 *bp;
-	volatile __u16 *p;
-
-	if (CHECK_AX88796L_PORT(port)) {
-		p = (volatile unsigned short *)port88796l(port, 0);
-		while (count--)
-			ctrl_outb(*p & 0xff, a++);
-	} else if (PXSEG(port))
-		while (count--)
-			ctrl_outb(ctrl_inb(port), a++);
-	else if (is_pci_ioaddr(port) || shifted_port(port)) {
-		bp = (__u8 *)pci_ioaddr(port);
-		while (count--)
-			ctrl_outb(*bp, a++);
-	} else {
-		p = (volatile unsigned short *)port2adr(port);
-		while (count--)
-			ctrl_outb(*p & 0xff, a++);
-	}
-}
-
-void rts7751r2d_insw(unsigned long port, void *addr, unsigned long count)
-{
-	unsigned long a = (unsigned long)addr;
-	volatile __u16 *p;
-
-	if (CHECK_AX88796L_PORT(port))
-		p = (volatile unsigned short *)port88796l(port, 1);
-	else if (PXSEG(port))
-		p = (volatile unsigned short *)port;
-	else if (is_pci_ioaddr(port) || shifted_port(port))
-		p = (volatile unsigned short *)pci_ioaddr(port);
-	else
-		p = (volatile unsigned short *)port2adr(port);
-	while (count--)
-		ctrl_outw(*p, a++);
-}
-
-void rts7751r2d_insl(unsigned long port, void *addr, unsigned long count)
-{
-	if (CHECK_AX88796L_PORT(port))
-		maybebadio(port);
-	else if (is_pci_ioaddr(port) || shifted_port(port)) {
-		unsigned long a = (unsigned long)addr;
-
-		while (count--) {
-			ctrl_outl(ctrl_inl(pci_ioaddr(port)), a);
-			a += 4;
-		}
-	} else
-		maybebadio(port);
-}
-
-void rts7751r2d_outsb(unsigned long port, const void *addr, unsigned long count)
-{
-	unsigned long a = (unsigned long)addr;
-	volatile __u8 *bp;
-	volatile __u16 *p;
-
-	if (CHECK_AX88796L_PORT(port)) {
-		p = (volatile unsigned short *)port88796l(port, 0);
-		while (count--)
-			*p = ctrl_inb(a++);
-	} else if (PXSEG(port))
-		while (count--)
-			ctrl_outb(a++, port);
-	else if (is_pci_ioaddr(port) || shifted_port(port)) {
-		bp = (__u8 *)pci_ioaddr(port);
-		while (count--)
-			*bp = ctrl_inb(a++);
-	} else {
-		p = (volatile unsigned short *)port2adr(port);
-		while (count--)
-			*p = ctrl_inb(a++);
-	}
-}
-
-void rts7751r2d_outsw(unsigned long port, const void *addr, unsigned long count)
-{
-	unsigned long a = (unsigned long)addr;
-	volatile __u16 *p;
-
-	if (CHECK_AX88796L_PORT(port))
-		p = (volatile unsigned short *)port88796l(port, 1);
-	else if (PXSEG(port))
-		p = (volatile unsigned short *)port;
-	else if (is_pci_ioaddr(port) || shifted_port(port))
-		p = (volatile unsigned short *)pci_ioaddr(port);
-	else
-		p = (volatile unsigned short *)port2adr(port);
-
-	while (count--) {
-		ctrl_outw(*p, a);
-		a += 2;
-	}
-}
-
-void rts7751r2d_outsl(unsigned long port, const void *addr, unsigned long count)
-{
-	if (CHECK_AX88796L_PORT(port))
-		maybebadio(port);
-	else if (is_pci_ioaddr(port) || shifted_port(port)) {
-		unsigned long a = (unsigned long)addr;
-
-		while (count--) {
-			ctrl_outl(ctrl_inl(a), pci_ioaddr(port));
-			a += 4;
-		}
-	} else
-		maybebadio(port);
-}
-
-unsigned long rts7751r2d_isa_port2addr(unsigned long offset)
-{
-	return port2adr(offset);
-}

arch/sh/boards/renesas/rts7751r2d/irq.c

@@ -9,7 +9,9 @@
  * Atom Create Engineering Co., Ltd. 2002.
  */
 #include <linux/init.h>
+#include <linux/interrupt.h>
 #include <linux/irq.h>
+#include <linux/interrupt.h>
 #include <linux/io.h>
 #include <asm/rts7751r2d.h>
 
@@ -22,79 +24,31 @@ static int mask_pos[] = {6, 11, 9, 8, 12, 10, 5, 4, 7, 14, 13, 0, 0, 0, 0};
 extern int voyagergx_irq_demux(int irq);
 extern void setup_voyagergx_irq(void);
 
-static void enable_rts7751r2d_irq(unsigned int irq);
-static void disable_rts7751r2d_irq(unsigned int irq);
-
-/* shutdown is same as "disable" */
-#define shutdown_rts7751r2d_irq disable_rts7751r2d_irq
-
-static void ack_rts7751r2d_irq(unsigned int irq);
-static void end_rts7751r2d_irq(unsigned int irq);
-
-static unsigned int startup_rts7751r2d_irq(unsigned int irq)
+static void enable_rts7751r2d_irq(unsigned int irq)
 {
-	enable_rts7751r2d_irq(irq);
-	return 0; /* never anything pending */
+	/* Set priority in IPR back to original value */
+	ctrl_outw(ctrl_inw(IRLCNTR1) | (1 << mask_pos[irq]), IRLCNTR1);
 }
 
 static void disable_rts7751r2d_irq(unsigned int irq)
 {
-	unsigned short val;
-	unsigned short mask = 0xffff ^ (0x0001 << mask_pos[irq]);
-
 	/* Set the priority in IPR to 0 */
-	val = ctrl_inw(IRLCNTR1);
-	val &= mask;
-	ctrl_outw(val, IRLCNTR1);
-}
-
-static void enable_rts7751r2d_irq(unsigned int irq)
-{
-	unsigned short val;
-	unsigned short value = (0x0001 << mask_pos[irq]);
-
-	/* Set priority in IPR back to original value */
-	val = ctrl_inw(IRLCNTR1);
-	val |= value;
-	ctrl_outw(val, IRLCNTR1);
+	ctrl_outw(ctrl_inw(IRLCNTR1) & (0xffff ^ (1 << mask_pos[irq])),
+		  IRLCNTR1);
 }
 
 int rts7751r2d_irq_demux(int irq)
 {
-	int demux_irq;
-
-	demux_irq = voyagergx_irq_demux(irq);
-	return demux_irq;
-}
-
-static void ack_rts7751r2d_irq(unsigned int irq)
-{
-	disable_rts7751r2d_irq(irq);
+	return voyagergx_irq_demux(irq);
 }
 
-static void end_rts7751r2d_irq(unsigned int irq)
-{
-	if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS)))
-		enable_rts7751r2d_irq(irq);
-}
-
-static struct hw_interrupt_type rts7751r2d_irq_type = {
-	.typename = "RTS7751R2D IRQ",
-	.startup = startup_rts7751r2d_irq,
-	.shutdown = shutdown_rts7751r2d_irq,
-	.enable = enable_rts7751r2d_irq,
-	.disable = disable_rts7751r2d_irq,
-	.ack = ack_rts7751r2d_irq,
-	.end = end_rts7751r2d_irq,
+static struct irq_chip rts7751r2d_irq_chip __read_mostly = {
+	.name		= "rts7751r2d",
+	.mask		= disable_rts7751r2d_irq,
+	.unmask		= enable_rts7751r2d_irq,
+	.mask_ack	= disable_rts7751r2d_irq,
 };
 
-static void make_rts7751r2d_irq(unsigned int irq)
-{
-	disable_irq_nosync(irq);
-	irq_desc[irq].chip = &rts7751r2d_irq_type;
-	disable_rts7751r2d_irq(irq);
-}
-
 /*
  * Initialize IRQ setting
  */
@@ -119,8 +73,12 @@ void __init init_rts7751r2d_IRQ(void)
 	 * IRL14=Extention #3
 	 */
 
-	for (i=0; i<15; i++)
-		make_rts7751r2d_irq(i);
+	for (i=0; i<15; i++) {
+		disable_irq_nosync(i);
+		set_irq_chip_and_handler_name(i, &rts7751r2d_irq_chip,
+					      handle_level_irq, "level");
+		enable_rts7751r2d_irq(i);
+	}
 
 	setup_voyagergx_irq();
 }

arch/sh/boards/renesas/rts7751r2d/setup.c

 /*
  * Renesas Technology Sales RTS7751R2D Support.
  *
- * Copyright (C) 2002 Atom Create Engineering Co., Ltd.
- * Copyright (C) 2004 - 2006 Paul Mundt
+ * Copyright (C) 2002 - 2006 Atom Create Engineering Co., Ltd.
+ * Copyright (C) 2004 - 2007 Paul Mundt
  *
  * This file is subject to the terms and conditions of the GNU General Public
  * License.  See the file "COPYING" in the main directory of this archive
@@ -10,33 +10,13 @@
  */
 #include <linux/init.h>
 #include <linux/platform_device.h>
+#include <linux/pata_platform.h>
 #include <linux/serial_8250.h>
 #include <linux/pm.h>
 #include <asm/machvec.h>
-#include <asm/mach/rts7751r2d.h>
-#include <asm/io.h>
+#include <asm/rts7751r2d.h>
 #include <asm/voyagergx.h>
-
-extern void heartbeat_rts7751r2d(void);
-extern void init_rts7751r2d_IRQ(void);
-extern int rts7751r2d_irq_demux(int irq);
-
-extern void *voyagergx_consistent_alloc(struct device *, size_t, dma_addr_t *, gfp_t);
-extern int voyagergx_consistent_free(struct device *, size_t, void *, dma_addr_t);
-
-static struct plat_serial8250_port uart_platform_data[] = {
-	{
-		.membase	= (void *)VOYAGER_UART_BASE,
-		.mapbase	= VOYAGER_UART_BASE,
-		.iotype		= UPIO_MEM,
-		.irq		= VOYAGER_UART0_IRQ,
-		.flags		= UPF_BOOT_AUTOCONF,
-		.regshift	= 2,
-		.uartclk	= (9600 * 16),
-	}, {
-		.flags		= 0,
-	},
-};
+#include <asm/io.h>
 
 static void __init voyagergx_serial_init(void)
 {
@@ -45,25 +25,72 @@ static void __init voyagergx_serial_init(void)
 	/*
 	 * GPIO Control
 	 */
-	val = inl(GPIO_MUX_HIGH);
+	val = readl((void __iomem *)GPIO_MUX_HIGH);
 	val |= 0x00001fe0;
-	outl(val, GPIO_MUX_HIGH);
+	writel(val, (void __iomem *)GPIO_MUX_HIGH);
 
 	/*
 	 * Power Mode Gate
 	 */
-	val = inl(POWER_MODE0_GATE);
+	val = readl((void __iomem *)POWER_MODE0_GATE);
 	val |= (POWER_MODE0_GATE_U0 | POWER_MODE0_GATE_U1);
-	outl(val, POWER_MODE0_GATE);
+	writel(val, (void __iomem *)POWER_MODE0_GATE);
 
-	val = inl(POWER_MODE1_GATE);
+	val = readl((void __iomem *)POWER_MODE1_GATE);
 	val |= (POWER_MODE1_GATE_U0 | POWER_MODE1_GATE_U1);
-	outl(val, POWER_MODE1_GATE);
+	writel(val, (void __iomem *)POWER_MODE1_GATE);
 }
 
+static struct resource cf_ide_resources[] = {
+	[0] = {
+		.start	= PA_AREA5_IO + 0x1000,
+		.end	= PA_AREA5_IO + 0x1000 + 0x08 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= PA_AREA5_IO + 0x80c,
+		.end	= PA_AREA5_IO + 0x80c + 0x16 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = {
+#ifdef CONFIG_RTS7751R2D_REV11
+		.start	= 1,
+#else
+		.start	= 2,
+#endif
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct pata_platform_info pata_info = {
+	.ioport_shift	= 1,
+};
+
+static struct platform_device cf_ide_device  = {
+	.name		= "pata_platform",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(cf_ide_resources),
+	.resource	= cf_ide_resources,
+	.dev	= {
+		.platform_data	= &pata_info,
+	},
+};
+
+static struct plat_serial8250_port uart_platform_data[] = {
+	{
+		.membase	= (void __iomem *)VOYAGER_UART_BASE,
+		.mapbase	= VOYAGER_UART_BASE,
+		.iotype		= UPIO_MEM,
+		.irq		= VOYAGER_UART0_IRQ,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.regshift	= 2,
+		.uartclk	= (9600 * 16),
+	}
+};
+
 static struct platform_device uart_device = {
 	.name		= "serial8250",
-	.id		= -1,
+	.id		= PLAT8250_DEV_PLATFORM,
 	.dev		= {
 		.platform_data	= uart_platform_data,
 	},
@@ -87,6 +114,7 @@ static struct platform_device heartbeat_device = {
 static struct platform_device *rts7751r2d_devices[] __initdata = {
 	&uart_device,
 	&heartbeat_device,
+	&cf_ide_device,
 };
 
 static int __init rts7751r2d_devices_setup(void)
@@ -94,6 +122,7 @@ static int __init rts7751r2d_devices_setup(void)
 	return platform_add_devices(rts7751r2d_devices,
 				    ARRAY_SIZE(rts7751r2d_devices));
 }
+__initcall(rts7751r2d_devices_setup);
 
 static void rts7751r2d_power_off(void)
 {
@@ -105,14 +134,17 @@ static void rts7751r2d_power_off(void)
  */
 static void __init rts7751r2d_setup(char **cmdline_p)
 {
-	device_initcall(rts7751r2d_devices_setup);
+	u16 ver = ctrl_inw(PA_VERREG);
+
+	printk(KERN_INFO "Renesas Technology Sales RTS7751R2D support.\n");
+
+	printk(KERN_INFO "FPGA version:%d (revision:%d)\n",
+					(ver >> 4) & 0xf, ver & 0xf);
 
 	ctrl_outw(0x0000, PA_OUTPORT);
 	pm_power_off = rts7751r2d_power_off;
 
 	voyagergx_serial_init();
-
-	printk(KERN_INFO "Renesas Technology Sales RTS7751R2D support.\n");
 }
 
 /*
@@ -123,27 +155,6 @@ struct sh_machine_vector mv_rts7751r2d __initmv = {
 	.mv_setup		= rts7751r2d_setup,
 	.mv_nr_irqs		= 72,
 
-	.mv_inb			= rts7751r2d_inb,
-	.mv_inw			= rts7751r2d_inw,
-	.mv_inl			= rts7751r2d_inl,
-	.mv_outb		= rts7751r2d_outb,
-	.mv_outw		= rts7751r2d_outw,
-	.mv_outl		= rts7751r2d_outl,
-
-	.mv_inb_p		= rts7751r2d_inb_p,
-	.mv_inw_p		= rts7751r2d_inw,
-	.mv_inl_p		= rts7751r2d_inl,
-	.mv_outb_p		= rts7751r2d_outb_p,
-	.mv_outw_p		= rts7751r2d_outw,
-	.mv_outl_p		= rts7751r2d_outl,
-
-	.mv_insb		= rts7751r2d_insb,
-	.mv_insw		= rts7751r2d_insw,
-	.mv_insl		= rts7751r2d_insl,
-	.mv_outsb		= rts7751r2d_outsb,
-	.mv_outsw		= rts7751r2d_outsw,
-	.mv_outsl		= rts7751r2d_outsl,
-
 	.mv_init_irq		= init_rts7751r2d_IRQ,
 	.mv_irq_demux		= rts7751r2d_irq_demux,
 

arch/sh/cchips/voyagergx/irq.c

@@ -28,21 +28,21 @@ static void disable_voyagergx_irq(unsigned int irq)
 	unsigned long val;
 	unsigned long mask = 1 << (irq - VOYAGER_IRQ_BASE);
 
-    	pr_debug("disable_voyagergx_irq(%d): mask=%lx\n", irq, mask);
-        val = inl(VOYAGER_INT_MASK);
-        val &= ~mask;
-        outl(val, VOYAGER_INT_MASK);
+	pr_debug("disable_voyagergx_irq(%d): mask=%x\n", irq, mask);
+	val = readl((void __iomem *)VOYAGER_INT_MASK);
+	val &= ~mask;
+	writel(val, (void __iomem *)VOYAGER_INT_MASK);
 }
 
 static void enable_voyagergx_irq(unsigned int irq)
 {
-        unsigned long val;
-        unsigned long mask = 1 << (irq - VOYAGER_IRQ_BASE);
+	unsigned long val;
+	unsigned long mask = 1 << (irq - VOYAGER_IRQ_BASE);
 
-        pr_debug("disable_voyagergx_irq(%d): mask=%lx\n", irq, mask);
-        val = inl(VOYAGER_INT_MASK);
-        val |= mask;
-        outl(val, VOYAGER_INT_MASK);
+	pr_debug("disable_voyagergx_irq(%d): mask=%x\n", irq, mask);
+	val = readl((void __iomem *)VOYAGER_INT_MASK);
+	val |= mask;
+	writel(val, (void __iomem *)VOYAGER_INT_MASK);
 }
 
 static void mask_and_ack_voyagergx(unsigned int irq)
@@ -68,20 +68,20 @@ static void shutdown_voyagergx_irq(unsigned int irq)
 }
 
 static struct hw_interrupt_type voyagergx_irq_type = {
-	.typename = "VOYAGERGX-IRQ",
-	.startup = startup_voyagergx_irq,
-	.shutdown = shutdown_voyagergx_irq,
-	.enable = enable_voyagergx_irq,
-	.disable = disable_voyagergx_irq,
-	.ack = mask_and_ack_voyagergx,
-	.end = end_voyagergx_irq,
+	.typename	= "VOYAGERGX-IRQ",
+	.startup	= startup_voyagergx_irq,
+	.shutdown	= shutdown_voyagergx_irq,
+	.enable		= enable_voyagergx_irq,
+	.disable	= disable_voyagergx_irq,
+	.ack		= mask_and_ack_voyagergx,
+	.end		= end_voyagergx_irq,
 };
 
 static irqreturn_t voyagergx_interrupt(int irq, void *dev_id)
 {
 	printk(KERN_INFO
 	       "VoyagerGX: spurious interrupt, status: 0x%x\n",
-	       		inl(INT_STATUS));
+			(unsigned int)readl((void __iomem *)INT_STATUS));
 	return IRQ_HANDLED;
 }
 
@@ -93,13 +93,13 @@ static struct {
 void voyagergx_register_irq_demux(int irq,
 		int (*demux)(int irq, void *dev), void *dev)
 {
-    	voyagergx_demux[irq - VOYAGER_IRQ_BASE].func = demux;
-    	voyagergx_demux[irq - VOYAGER_IRQ_BASE].dev = dev;
+	voyagergx_demux[irq - VOYAGER_IRQ_BASE].func = demux;
+	voyagergx_demux[irq - VOYAGER_IRQ_BASE].dev = dev;
 }
 
 void voyagergx_unregister_irq_demux(int irq)
 {
-    	voyagergx_demux[irq - VOYAGER_IRQ_BASE].func = 0;
+	voyagergx_demux[irq - VOYAGER_IRQ_BASE].func = 0;
 }
 
 int voyagergx_irq_demux(int irq)
@@ -107,31 +107,25 @@ int voyagergx_irq_demux(int irq)
 
 	if (irq == IRQ_VOYAGER ) {
 		unsigned long i = 0, bit __attribute__ ((unused));
-		unsigned long val  = inl(INT_STATUS);
-#if 1
-		if ( val & ( 1 << 1 )){
+		unsigned long val  = readl((void __iomem *)INT_STATUS);
+
+		if (val & (1 << 1))
 			i = 1;
-		} else if ( val & ( 1 << 2 )){
+		else if (val & (1 << 2))
 			i = 2;
-		} else if ( val & ( 1 << 6 )){
+		else if (val & (1 << 6))
 			i = 6;
-		} else if( val & ( 1 << 10 )){
+		else if (val & (1 << 10))
 			i = 10;
-		} else if( val & ( 1 << 11 )){
+		else if (val & (1 << 11))
 			i = 11;
-		} else if( val & ( 1 << 12 )){
+		else if (val & (1 << 12))
 			i = 12;
-		} else if( val & ( 1 << 17 )){
+		else if (val & (1 << 17))
 			i = 17;
-		} else {
+		else
 			printk("Unexpected IRQ irq = %d status = 0x%08lx\n", irq, val);
-		}
-		pr_debug("voyagergx_irq_demux %ld\n", i);
-#else
-		for (bit = 1, i = 0 ; i < VOYAGER_IRQ_NUM ; bit <<= 1, i++)
-			if (val & bit)
-				break;
-#endif
+		pr_debug("voyagergx_irq_demux %d \n", i);
     	    	if (i < VOYAGER_IRQ_NUM) {
 			irq = VOYAGER_IRQ_BASE + i;
     	    		if (voyagergx_demux[i].func != 0)

arch/sh/cchips/voyagergx/setup.c

@@ -19,7 +19,7 @@ static int __init setup_voyagergx(void)
 {
 	unsigned long val;
 
-	val = inl(DRAM_CTRL);
+	val = readl((void __iomem *)DRAM_CTRL);
 	val |= (DRAM_CTRL_CPU_COLUMN_SIZE_256	|
 		DRAM_CTRL_CPU_ACTIVE_PRECHARGE	|
 		DRAM_CTRL_CPU_RESET		|
@@ -29,7 +29,7 @@ static int __init setup_voyagergx(void)
 		DRAM_CTRL_ACTIVE_PRECHARGE	|
 		DRAM_CTRL_RESET			|
 		DRAM_CTRL_REMAIN_ACTIVE);
-	outl(val, DRAM_CTRL);
+	writel(val, (void __iomem *)DRAM_CTRL);
 
 	return 0;
 }

arch/sh/configs/rts7751r2d_defconfig

 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.18
-# Tue Oct  3 11:38:36 2006
+# Linux kernel version: 2.6.20
+# Thu Feb 15 17:17:29 2007
 #
 CONFIG_SUPERH=y
 CONFIG_RWSEM_GENERIC_SPINLOCK=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_HWEIGHT=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 CONFIG_GENERIC_IRQ_PROBE=y
 CONFIG_GENERIC_CALIBRATE_DELAY=y
+# CONFIG_GENERIC_TIME is not set
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
 
 #
@@ -33,8 +39,8 @@ CONFIG_SYSVIPC=y
 # CONFIG_UTS_NS is not set
 # CONFIG_AUDIT is not set
 # CONFIG_IKCONFIG is not set
+CONFIG_SYSFS_DEPRECATED=y
 # CONFIG_RELAY is not set
-CONFIG_INITRAMFS_SOURCE=""
 # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
 CONFIG_SYSCTL=y
 CONFIG_EMBEDDED=y
@@ -97,10 +103,8 @@ CONFIG_DEFAULT_IOSCHED="anticipatory"
 # CONFIG_SH_73180_SOLUTION_ENGINE is not set
 # CONFIG_SH_7751_SYSTEMH is not set
 # CONFIG_SH_HP6XX is not set
-# CONFIG_SH_EC3104 is not set
 # CONFIG_SH_SATURN is not set
 # CONFIG_SH_DREAMCAST is not set
-# CONFIG_SH_BIGSUR is not set
 # CONFIG_SH_MPC1211 is not set
 # CONFIG_SH_SH03 is not set
 # CONFIG_SH_SECUREEDGE5410 is not set
@@ -113,6 +117,9 @@ CONFIG_SH_RTS7751R2D=y
 # CONFIG_SH_LANDISK is not set
 # CONFIG_SH_TITAN is not set
 # CONFIG_SH_SHMIN is not set
+# CONFIG_SH_7206_SOLUTION_ENGINE is not set
+# CONFIG_SH_7619_SOLUTION_ENGINE is not set
+# CONFIG_SH_ASDAP310 is not set
 # CONFIG_SH_UNKNOWN is not set
 
 #
@@ -124,6 +131,12 @@ CONFIG_CPU_SH4=y
 # SH-2 Processor Support
 #
 # CONFIG_CPU_SUBTYPE_SH7604 is not set
+# CONFIG_CPU_SUBTYPE_SH7619 is not set
+
+#
+# SH-2A Processor Support
+#
+# CONFIG_CPU_SUBTYPE_SH7206 is not set
 
 #
 # SH-3 Processor Support
@@ -159,12 +172,14 @@ CONFIG_CPU_SUBTYPE_SH7751R=y
 #
 # CONFIG_CPU_SUBTYPE_SH7770 is not set
 # CONFIG_CPU_SUBTYPE_SH7780 is not set
+# CONFIG_CPU_SUBTYPE_SH7785 is not set
 
 #
 # SH4AL-DSP Processor Support
 #
 # CONFIG_CPU_SUBTYPE_SH73180 is not set
 # CONFIG_CPU_SUBTYPE_SH7343 is not set
+# CONFIG_CPU_SUBTYPE_SH7722 is not set
 
 #
 # Memory management options
@@ -174,6 +189,9 @@ CONFIG_PAGE_OFFSET=0x80000000
 CONFIG_MEMORY_START=0x0c000000
 CONFIG_MEMORY_SIZE=0x04000000
 CONFIG_VSYSCALL=y
+CONFIG_PAGE_SIZE_4KB=y
+# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PAGE_SIZE_64KB is not set
 CONFIG_SELECT_MEMORY_MODEL=y
 CONFIG_FLATMEM_MANUAL=y
 # CONFIG_DISCONTIGMEM_MANUAL is not set
@@ -183,6 +201,7 @@ CONFIG_FLAT_NODE_MEM_MAP=y
 # CONFIG_SPARSEMEM_STATIC is not set
 CONFIG_SPLIT_PTLOCK_CPUS=4
 # CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
 
 #
 # Cache configuration
@@ -195,11 +214,14 @@ CONFIG_SPLIT_PTLOCK_CPUS=4
 # Processor features
 #
 CONFIG_CPU_LITTLE_ENDIAN=y
+# CONFIG_CPU_BIG_ENDIAN is not set
 CONFIG_SH_FPU=y
 # CONFIG_SH_DSP is not set
 # CONFIG_SH_STORE_QUEUES is not set
 CONFIG_CPU_HAS_INTEVT=y
+CONFIG_CPU_HAS_IPR_IRQ=y
 CONFIG_CPU_HAS_SR_RB=y
+CONFIG_CPU_HAS_PTEA=y
 
 #
 # Timer support
@@ -210,6 +232,8 @@ CONFIG_SH_TMU=y
 # RTS7751R2D options
 #
 CONFIG_RTS7751R2D_REV11=y
+CONFIG_SH_TIMER_IRQ=16
+# CONFIG_NO_IDLE_HZ is not set
 CONFIG_SH_PCLK_FREQ=60000000
 
 #
@@ -231,11 +255,17 @@ CONFIG_VOYAGERGX=y
 # CONFIG_HD6446X_SERIES is not set
 CONFIG_HEARTBEAT=y
 
+#
+# Additional SuperH Device Drivers
+#
+# CONFIG_PUSH_SWITCH is not set
+
 #
 # Kernel features
 #
 # CONFIG_HZ_100 is not set
 CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
 # CONFIG_HZ_1000 is not set
 CONFIG_HZ=250
 # CONFIG_KEXEC is not set
@@ -251,7 +281,7 @@ CONFIG_ZERO_PAGE_OFFSET=0x00010000
 CONFIG_BOOT_LINK_OFFSET=0x00800000
 # CONFIG_UBC_WAKEUP is not set
 CONFIG_CMDLINE_BOOL=y
-CONFIG_CMDLINE="mem=64M console=ttySC0,115200 root=/dev/hda1"
+CONFIG_CMDLINE="console=ttySC0,115200 root=/dev/sda1"
 
 #
 # Bus options
@@ -260,7 +290,6 @@ CONFIG_PCI=y
 CONFIG_SH_PCIDMA_NONCOHERENT=y
 CONFIG_PCI_AUTO=y
 CONFIG_PCI_AUTO_UPDATE_RESOURCES=y
-# CONFIG_PCI_MULTITHREAD_PROBE is not set
 
 #
 # PCCARD (PCMCIA/CardBus) support
@@ -302,6 +331,7 @@ CONFIG_UNIX=y
 CONFIG_XFRM=y
 # CONFIG_XFRM_USER is not set
 # CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
 # CONFIG_NET_KEY is not set
 CONFIG_INET=y
 # CONFIG_IP_MULTICAST is not set
@@ -319,11 +349,13 @@ CONFIG_IP_FIB_HASH=y
 # CONFIG_INET_TUNNEL is not set
 CONFIG_INET_XFRM_MODE_TRANSPORT=y
 CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
 CONFIG_INET_DIAG=y
 CONFIG_INET_TCP_DIAG=y
 # CONFIG_TCP_CONG_ADVANCED is not set
 CONFIG_TCP_CONG_CUBIC=y
 CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
 # CONFIG_IPV6 is not set
 # CONFIG_INET6_XFRM_TUNNEL is not set
 # CONFIG_INET6_TUNNEL is not set
@@ -380,7 +412,7 @@ CONFIG_WIRELESS_EXT=y
 #
 CONFIG_STANDALONE=y
 CONFIG_PREVENT_FIRMWARE_BUILD=y
-# CONFIG_FW_LOADER is not set
+CONFIG_FW_LOADER=m
 # CONFIG_SYS_HYPERVISOR is not set
 
 #
@@ -422,44 +454,145 @@ CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
 # CONFIG_ATA_OVER_ETH is not set
 
 #
-# ATA/ATAPI/MFM/RLL support
-#
-CONFIG_IDE=y
-CONFIG_IDE_MAX_HWIFS=4
-CONFIG_BLK_DEV_IDE=y
-
-#
-# Please see Documentation/ide.txt for help/info on IDE drives
+# Misc devices
 #
-# CONFIG_BLK_DEV_IDE_SATA is not set
-CONFIG_BLK_DEV_IDEDISK=y
-# CONFIG_IDEDISK_MULTI_MODE is not set
-# CONFIG_BLK_DEV_IDECD is not set
-# CONFIG_BLK_DEV_IDETAPE is not set
-# CONFIG_BLK_DEV_IDEFLOPPY is not set
-# CONFIG_IDE_TASK_IOCTL is not set
+# CONFIG_SGI_IOC4 is not set
+# CONFIG_TIFM_CORE is not set
 
 #
-# IDE chipset support/bugfixes
+# ATA/ATAPI/MFM/RLL support
 #
-CONFIG_IDE_GENERIC=y
-# CONFIG_BLK_DEV_IDEPCI is not set
-# CONFIG_IDE_ARM is not set
-# CONFIG_BLK_DEV_IDEDMA is not set
-# CONFIG_IDEDMA_AUTO is not set
-# CONFIG_BLK_DEV_HD is not set
+# CONFIG_IDE is not set
 
 #
 # SCSI device support
 #
 # CONFIG_RAID_ATTRS is not set
-# CONFIG_SCSI is not set
+CONFIG_SCSI=y
+# CONFIG_SCSI_TGT is not set
 # CONFIG_SCSI_NETLINK is not set
+CONFIG_SCSI_PROC_FS=y
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=y
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+# CONFIG_CHR_DEV_SG is not set
+# CONFIG_CHR_DEV_SCH is not set
+
+#
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+#
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+
+#
+# SCSI Transports
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
+
+#
+# SCSI low-level drivers
+#
+# CONFIG_ISCSI_TCP is not set
+# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
+# CONFIG_SCSI_3W_9XXX is not set
+# CONFIG_SCSI_ACARD is not set
+# CONFIG_SCSI_AACRAID is not set
+# CONFIG_SCSI_AIC7XXX is not set
+# CONFIG_SCSI_AIC7XXX_OLD is not set
+# CONFIG_SCSI_AIC79XX is not set
+# CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_DPT_I2O is not set
+# CONFIG_SCSI_ARCMSR is not set
+# CONFIG_MEGARAID_NEWGEN is not set
+# CONFIG_MEGARAID_LEGACY is not set
+# CONFIG_MEGARAID_SAS is not set
+# CONFIG_SCSI_HPTIOP is not set
+# CONFIG_SCSI_DMX3191D is not set
+# CONFIG_SCSI_FUTURE_DOMAIN is not set
+# CONFIG_SCSI_IPS is not set
+# CONFIG_SCSI_INITIO is not set
+# CONFIG_SCSI_INIA100 is not set
+# CONFIG_SCSI_STEX is not set
+# CONFIG_SCSI_SYM53C8XX_2 is not set
+# CONFIG_SCSI_IPR is not set
+# CONFIG_SCSI_QLOGIC_1280 is not set
+# CONFIG_SCSI_QLA_FC is not set
+# CONFIG_SCSI_QLA_ISCSI is not set
+# CONFIG_SCSI_LPFC is not set
+# CONFIG_SCSI_DC395x is not set
+# CONFIG_SCSI_DC390T is not set
+# CONFIG_SCSI_NSP32 is not set
+# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_SRP is not set
 
 #
 # Serial ATA (prod) and Parallel ATA (experimental) drivers
 #
-# CONFIG_ATA is not set
+CONFIG_ATA=y
+# CONFIG_ATA_NONSTANDARD is not set
+# CONFIG_SATA_AHCI is not set
+# CONFIG_SATA_SVW is not set
+# CONFIG_ATA_PIIX is not set
+# CONFIG_SATA_MV is not set
+# CONFIG_SATA_NV is not set
+# CONFIG_PDC_ADMA is not set
+# CONFIG_SATA_QSTOR is not set
+# CONFIG_SATA_PROMISE is not set
+# CONFIG_SATA_SX4 is not set
+# CONFIG_SATA_SIL is not set
+# CONFIG_SATA_SIL24 is not set
+# CONFIG_SATA_SIS is not set
+# CONFIG_SATA_ULI is not set
+# CONFIG_SATA_VIA is not set
+# CONFIG_SATA_VITESSE is not set
+# CONFIG_SATA_INIC162X is not set
+# CONFIG_PATA_ALI is not set
+# CONFIG_PATA_AMD is not set
+# CONFIG_PATA_ARTOP is not set
+# CONFIG_PATA_ATIIXP is not set
+# CONFIG_PATA_CMD64X is not set
+# CONFIG_PATA_CS5520 is not set
+# CONFIG_PATA_CS5530 is not set
+# CONFIG_PATA_CYPRESS is not set
+# CONFIG_PATA_EFAR is not set
+# CONFIG_ATA_GENERIC is not set
+# CONFIG_PATA_HPT366 is not set
+# CONFIG_PATA_HPT37X is not set
+# CONFIG_PATA_HPT3X2N is not set
+# CONFIG_PATA_HPT3X3 is not set
+# CONFIG_PATA_IT821X is not set
+# CONFIG_PATA_IT8213 is not set
+# CONFIG_PATA_JMICRON is not set
+# CONFIG_PATA_TRIFLEX is not set
+# CONFIG_PATA_MARVELL is not set
+# CONFIG_PATA_MPIIX is not set
+# CONFIG_PATA_OLDPIIX is not set
+# CONFIG_PATA_NETCELL is not set
+# CONFIG_PATA_NS87410 is not set
+# CONFIG_PATA_OPTI is not set
+# CONFIG_PATA_OPTIDMA is not set
+# CONFIG_PATA_PDC_OLD is not set
+# CONFIG_PATA_RADISYS is not set
+# CONFIG_PATA_RZ1000 is not set
+# CONFIG_PATA_SC1200 is not set
+# CONFIG_PATA_SERVERWORKS is not set
+# CONFIG_PATA_PDC2027X is not set
+# CONFIG_PATA_SIL680 is not set
+# CONFIG_PATA_SIS is not set
+# CONFIG_PATA_VIA is not set
+# CONFIG_PATA_WINBOND is not set
+CONFIG_PATA_PLATFORM=y
 
 #
 # Multi-device support (RAID and LVM)
@@ -470,6 +603,9 @@ CONFIG_IDE_GENERIC=y
 # Fusion MPT device support
 #
 # CONFIG_FUSION is not set
+# CONFIG_FUSION_SPI is not set
+# CONFIG_FUSION_FC is not set
+# CONFIG_FUSION_SAS is not set
 
 #
 # IEEE 1394 (FireWire) support
@@ -540,6 +676,7 @@ CONFIG_8139TOO=y
 # CONFIG_SUNDANCE is not set
 # CONFIG_TLAN is not set
 # CONFIG_VIA_RHINE is not set
+# CONFIG_SC92031 is not set
 
 #
 # Ethernet (1000 Mbit)
@@ -559,14 +696,17 @@ CONFIG_8139TOO=y
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
 # CONFIG_QLA3XXX is not set
+# CONFIG_ATL1 is not set
 
 #
 # Ethernet (10000 Mbit)
 #
 # CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
 # CONFIG_IXGB is not set
 # CONFIG_S2IO is not set
 # CONFIG_MYRI10GE is not set
+# CONFIG_NETXEN_NIC is not set
 
 #
 # Token Ring devices
@@ -611,6 +751,7 @@ CONFIG_NET_WIRELESS=y
 # CONFIG_HIPPI is not set
 # CONFIG_PPP is not set
 # CONFIG_SLIP is not set
+# CONFIG_NET_FC is not set
 # CONFIG_SHAPER is not set
 # CONFIG_NETCONSOLE is not set
 # CONFIG_NETPOLL is not set
@@ -646,14 +787,23 @@ CONFIG_NET_WIRELESS=y
 #
 # Serial drivers
 #
-# CONFIG_SERIAL_8250 is not set
+CONFIG_SERIAL_8250=y
+# CONFIG_SERIAL_8250_CONSOLE is not set
+CONFIG_SERIAL_8250_PCI=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+# CONFIG_SERIAL_8250_EXTENDED is not set
 
 #
 # Non-8250 serial port support
 #
-# CONFIG_SERIAL_SH_SCI is not set
+CONFIG_SERIAL_SH_SCI=y
+CONFIG_SERIAL_SH_SCI_NR_UARTS=1
+CONFIG_SERIAL_SH_SCI_CONSOLE=y
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
 # CONFIG_SERIAL_JSM is not set
-# CONFIG_UNIX98_PTYS is not set
+CONFIG_UNIX98_PTYS=y
 CONFIG_LEGACY_PTYS=y
 CONFIG_LEGACY_PTY_COUNT=256
 
@@ -671,10 +821,6 @@ CONFIG_HW_RANDOM=y
 # CONFIG_DTLK is not set
 # CONFIG_R3964 is not set
 # CONFIG_APPLICOM is not set
-
-#
-# Ftape, the floppy tape device driver
-#
 # CONFIG_DRM is not set
 # CONFIG_RAW_DRIVER is not set
 
@@ -682,7 +828,6 @@ CONFIG_HW_RANDOM=y
 # TPM devices
 #
 # CONFIG_TCG_TPM is not set
-# CONFIG_TELCLOCK is not set
 
 #
 # I2C support
@@ -698,6 +843,7 @@ CONFIG_HW_RANDOM=y
 #
 # Dallas's 1-wire bus
 #
+# CONFIG_W1 is not set
 
 #
 # Hardware Monitoring support
@@ -706,18 +852,14 @@ CONFIG_HWMON=y
 # CONFIG_HWMON_VID is not set
 # CONFIG_SENSORS_ABITUGURU is not set
 # CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_PC87427 is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_HWMON_DEBUG_CHIP is not set
 
-#
-# Misc devices
-#
-
 #
 # Multimedia devices
 #
 # CONFIG_VIDEO_DEV is not set
-CONFIG_VIDEO_V4L2=y
 
 #
 # Digital Video Broadcasting Devices
@@ -759,7 +901,6 @@ CONFIG_SND_VERBOSE_PROCFS=y
 CONFIG_SND_MPU401_UART=m
 CONFIG_SND_OPL3_LIB=m
 CONFIG_SND_AC97_CODEC=m
-CONFIG_SND_AC97_BUS=m
 # CONFIG_SND_DUMMY is not set
 # CONFIG_SND_MTPAV is not set
 # CONFIG_SND_SERIAL_U16550 is not set
@@ -782,6 +923,18 @@ CONFIG_SND_AC97_BUS=m
 # CONFIG_SND_CMIPCI is not set
 # CONFIG_SND_CS4281 is not set
 # CONFIG_SND_CS46XX is not set
+# CONFIG_SND_DARLA20 is not set
+# CONFIG_SND_GINA20 is not set
+# CONFIG_SND_LAYLA20 is not set
+# CONFIG_SND_DARLA24 is not set
+# CONFIG_SND_GINA24 is not set
+# CONFIG_SND_LAYLA24 is not set
+# CONFIG_SND_MONA is not set
+# CONFIG_SND_MIA is not set
+# CONFIG_SND_ECHO3G is not set
+# CONFIG_SND_INDIGO is not set
+# CONFIG_SND_INDIGOIO is not set
+# CONFIG_SND_INDIGODJ is not set
 # CONFIG_SND_EMU10K1 is not set
 # CONFIG_SND_EMU10K1X is not set
 # CONFIG_SND_ENS1370 is not set
@@ -801,6 +954,7 @@ CONFIG_SND_AC97_BUS=m
 # CONFIG_SND_MIXART is not set
 # CONFIG_SND_NM256 is not set
 # CONFIG_SND_PCXHR is not set
+# CONFIG_SND_RIPTIDE is not set
 # CONFIG_SND_RME32 is not set
 # CONFIG_SND_RME96 is not set
 # CONFIG_SND_RME9652 is not set
@@ -812,18 +966,23 @@ CONFIG_SND_AC97_BUS=m
 CONFIG_SND_YMFPCI=m
 # CONFIG_SND_AC97_POWER_SAVE is not set
 
+#
+# SoC audio support
+#
+# CONFIG_SND_SOC is not set
+
 #
 # Open Sound System
 #
 CONFIG_SOUND_PRIME=m
-# CONFIG_OSS_OBSOLETE_DRIVER is not set
+# CONFIG_OBSOLETE_OSS is not set
 # CONFIG_SOUND_BT878 is not set
-# CONFIG_SOUND_ES1371 is not set
 # CONFIG_SOUND_ICH is not set
 # CONFIG_SOUND_TRIDENT is not set
 # CONFIG_SOUND_MSNDCLAS is not set
 # CONFIG_SOUND_MSNDPIN is not set
 # CONFIG_SOUND_VIA82CXXX is not set
+CONFIG_AC97_BUS=m
 
 #
 # USB support
@@ -872,7 +1031,29 @@ CONFIG_USB_ARCH_HAS_EHCI=y
 #
 # Real Time Clock
 #
-# CONFIG_RTC_CLASS is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+
+#
+# RTC drivers
+#
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+CONFIG_RTC_DRV_SH=y
+# CONFIG_RTC_DRV_TEST is not set
+# CONFIG_RTC_DRV_V3020 is not set
 
 #
 # DMA Engine support
@@ -887,6 +1068,14 @@ CONFIG_USB_ARCH_HAS_EHCI=y
 # DMA Devices
 #
 
+#
+# Auxiliary Display support
+#
+
+#
+# Virtualization
+#
+
 #
 # File systems
 #
@@ -894,10 +1083,12 @@ CONFIG_EXT2_FS=y
 # CONFIG_EXT2_FS_XATTR is not set
 # CONFIG_EXT2_FS_XIP is not set
 # CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 CONFIG_MINIX_FS=y
 # CONFIG_ROMFS_FS is not set
@@ -932,7 +1123,8 @@ CONFIG_PROC_FS=y
 CONFIG_PROC_KCORE=y
 CONFIG_PROC_SYSCTL=y
 CONFIG_SYSFS=y
-# CONFIG_TMPFS is not set
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
 # CONFIG_HUGETLBFS is not set
 # CONFIG_HUGETLB_PAGE is not set
 CONFIG_RAMFS=y
@@ -1017,6 +1209,11 @@ CONFIG_NLS_CODEPAGE_932=y
 # CONFIG_NLS_KOI8_U is not set
 # CONFIG_NLS_UTF8 is not set
 
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+
 #
 # Profiling support
 #
@@ -1026,16 +1223,20 @@ CONFIG_OPROFILE=y
 #
 # Kernel hacking
 #
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 # CONFIG_PRINTK_TIME is not set
 CONFIG_ENABLE_MUST_CHECK=y
 # CONFIG_MAGIC_SYSRQ is not set
 # CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
 # CONFIG_DEBUG_KERNEL is not set
 CONFIG_LOG_BUF_SHIFT=14
 # CONFIG_DEBUG_BUGVERBOSE is not set
-# CONFIG_DEBUG_FS is not set
 # CONFIG_SH_STANDARD_BIOS is not set
-# CONFIG_EARLY_SCIF_CONSOLE is not set
+CONFIG_EARLY_SCIF_CONSOLE=y
+CONFIG_EARLY_SCIF_CONSOLE_PORT=0xffe80000
+CONFIG_EARLY_PRINTK=y
 # CONFIG_KGDB is not set
 
 #
@@ -1052,8 +1253,11 @@ CONFIG_LOG_BUF_SHIFT=14
 #
 # Library routines
 #
+CONFIG_BITREVERSE=y
 # CONFIG_CRC_CCITT is not set
 # CONFIG_CRC16 is not set
 CONFIG_CRC32=y
 # CONFIG_LIBCRC32C is not set
 CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y

arch/sh/kernel/cpu/sh4/setup-sh7750.c

@@ -46,11 +46,13 @@ static struct platform_device rtc_device = {
 
 static struct plat_sci_port sci_platform_data[] = {
 	{
+#ifndef CONFIG_SH_RTS7751R2D
 		.mapbase	= 0xffe00000,
 		.flags		= UPF_BOOT_AUTOCONF,
 		.type		= PORT_SCI,
 		.irqs		= { 23, 24, 25, 0 },
 	}, {
+#endif
 		.mapbase	= 0xffe80000,
 		.flags		= UPF_BOOT_AUTOCONF,
 		.type		= PORT_SCIF,

arch/sh/kernel/io_generic.c

-/* $Id: io_generic.c,v 1.2 2003/05/04 19:29:53 lethal Exp $
- *
- * linux/arch/sh/kernel/io_generic.c
+/*
+ * arch/sh/kernel/io_generic.c
  *
  * Copyright (C) 2000  Niibe Yutaka
- * Copyright (C) 2005  Paul Mundt
+ * Copyright (C) 2005 - 2007 Paul Mundt
  *
  * Generic I/O routine. These can be used where a machine specific version
  * is not required.
@@ -13,8 +12,9 @@
  * for more details.
  */
 #include <linux/module.h>
-#include <asm/io.h>
+#include <linux/io.h>
 #include <asm/machvec.h>
+#include <asm/cacheflush.h>
 
 #ifdef CONFIG_CPU_SH3
 /* SH3 has a PCMCIA bug that needs a dummy read from area 6 for a
@@ -96,6 +96,7 @@ void generic_insw(unsigned long port, void *dst, unsigned long count)
 	while (count--)
 		*buf++ = *port_addr;
 
+	flush_dcache_all();
 	dummy_read();
 }
 
@@ -170,6 +171,7 @@ void generic_outsw(unsigned long port, const void *src, unsigned long count)
 	while (count--)
 		*port_addr = *buf++;
 
+	flush_dcache_all();
 	dummy_read();
 }
 

include/asm-sh/rts7751r2d.h

@@ -68,6 +68,10 @@
 #define IRQ_PCISLOT2	10		/* PCI Slot #2 IRQ */
 #define	IRQ_EXTENTION	11		/* EXTn IRQ */
 
+/* arch/sh/boards/renesas/rts7751r2d/irq.c */
+void init_rts7751r2d_IRQ(void);
+int rts7751r2d_irq_demux(int);
+
 #define __IO_PREFIX rts7751r2d
 #include <asm/io_generic.h>
 

include/asm-sh/serial.h

@@ -29,10 +29,7 @@
 
 #else
 
-#define SERIAL_PORT_DFNS			\
-	/* UART CLK   PORT IRQ     FLAGS        */			\
-	{ 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS },	/* ttyS0 */	\
-	{ 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }	/* ttyS1 */
+#define SERIAL_PORT_DFNS
 
 #endif
 

include/asm-sh/voyagergx.h

@@ -308,6 +308,9 @@
 #define AC97C_READ			(1 << 19)
 #define AC97C_WD_BIT			(1 << 2)
 #define AC97C_INDEX_MASK		0x7f
-/* -------------------------------------------------------------------- */
+
+/* arch/sh/cchips/voyagergx/consistent.c */
+void *voyagergx_consistent_alloc(struct device *, size_t, dma_addr_t *, gfp_t);
+int voyagergx_consistent_free(struct device *, size_t, void *, dma_addr_t);
 
 #endif /* _VOYAGER_GX_REG_H */