Merge tag 'phy-for-5.18' of...

Merge tag 'phy-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into char-misc-next

Vinod writes:

phy-for-5.18

  - New support:
        - Mediatek tphy support for MT8186
	- Qualcomm usb phy support for sc8180x and sc8280xp
	- Qualcomm ufs phy support for sc8180x and sc8280xp
	- Qualcomm usb phy support for MSM8953
	- Cadence D-Phy Rx support
	- Sun4i support for USB phy
	- Rockchip naneng combo phy support for RK3568
	- Qualcomm eDP PHY for sc7280

  - Updates:
        - wake on support for Synopsis XHCI controllers
	- Yamilify Qualcomm USB HS phy binding
	- Charger detection support for TI tusb1210

* tag 'phy-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (53 commits)
  phy: qcom-qmp: add sc8280xp UFS PHY
  dt-bindings: phy: qcom,qmp: add sc8180x and sc8280xp ufs compatibles
  phy: qcom-snps: Add sc8280xp support
  dt-bindings: phy: qcom,usb-snps-femto-v2: Add sc8180x and sc8280xp
  dt-bindings: Revert "dt-bindings: soc: grf: add naneng combo phy register compatible"
  phy: dt-bindings: Add Cadence D-PHY Rx bindings
  phy: dt-bindings: cdns,dphy: add power-domains property
  phy: dt-bindings: Convert Cadence DPHY binding to YAML
  phy: cadence: Add Cadence D-PHY Rx driver
  dt-bindings: phy: renesas,usb2-phy: Document RZ/V2L phy bindings
  Revert "PCI: aardvark: Fix initialization with old Marvell's Arm Trusted Firmware"
  Revert "usb: host: xhci: mvebu: make USB 3.0 PHY optional for Armada 3720"
  Revert "ata: ahci: mvebu: Make SATA PHY optional for Armada 3720"
  phy: marvell: phy-mvebu-a3700-comphy: Add native kernel implementation
  phy: marvell: phy-mvebu-a3700-comphy: Remove port from driver configuration
  phy: phy-brcm-usb: fixup BCM4908 support
  dt-bindings: phy: mediatek,tphy: Add compatible for MT8192
  phy: ti: tusb1210: Add charger detection
  phy: ti: tusb1210: Add a delay between power-on and restoring the phy-parameters
  phy: ti: tusb1210: Drop tusb->vendor_specific2 != 0 check from tusb1210_power_on()
  ...

Documentation/devicetree/bindings/phy/allwinner,sun50i-a64-usb-phy.yaml

@@ -15,7 +15,9 @@ properties:
     const: 1
 
   compatible:
-    const: allwinner,sun50i-a64-usb-phy
+    enum:
+      - allwinner,sun20i-d1-usb-phy
+      - allwinner,sun50i-a64-usb-phy
 
   reg:
     items:

Documentation/devicetree/bindings/phy/cdns,dphy-rx.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/cdns,dphy-rx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cadence DPHY Rx Device Tree Bindings
+
+maintainers:
+  - Pratyush Yadav <p.yadav@ti.com>
+
+properties:
+  compatible:
+    items:
+      - const: cdns,dphy-rx
+
+  reg:
+    maxItems: 1
+
+  "#phy-cells":
+    const: 0
+
+  power-domains:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - "#phy-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/soc/ti,sci_pm_domain.h>
+
+    dphy0: phy@4580000 {
+        compatible = "cdns,dphy-rx";
+        reg = <0x4580000 0x1100>;
+        #phy-cells = <0>;
+        power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>;
+    };

Documentation/devicetree/bindings/phy/cdns,dphy.txt

-Cadence DPHY
-============
-
-Cadence DPHY block.
-
-Required properties:
-- compatible: should be set to "cdns,dphy".
-- reg: physical base address and length of the DPHY registers.
-- clocks: DPHY reference clocks.
-- clock-names: must contain "psm" and "pll_ref".
-- #phy-cells: must be set to 0.
-
-Example:
-	dphy0: dphy@fd0e0000{
-		compatible = "cdns,dphy";
-		reg = <0x0 0xfd0e0000 0x0 0x1000>;
-		clocks = <&psm_clk>, <&pll_ref_clk>;
-		clock-names = "psm", "pll_ref";
-		#phy-cells = <0>;
-	};

Documentation/devicetree/bindings/phy/cdns,dphy.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/cdns,dphy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cadence DPHY Device Tree Bindings
+
+maintainers:
+  - Pratyush Yadav <p.yadav@ti.com>
+
+properties:
+  compatible:
+    items:
+      - const: cdns,dphy
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: PMA state machine clock
+      - description: PLL reference clock
+
+  clock-names:
+    items:
+      - const: psm
+      - const: pll_ref
+
+  "#phy-cells":
+    const: 0
+
+  power-domains:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - "#phy-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/soc/ti,sci_pm_domain.h>
+
+    dphy0: phy@fd0e0000{
+        compatible = "cdns,dphy";
+        reg = <0xfd0e0000 0x1000>;
+        clocks = <&psm_clk>, <&pll_ref_clk>;
+        clock-names = "psm", "pll_ref";
+        power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>;
+        #phy-cells = <0>;
+    };

Documentation/devicetree/bindings/phy/mediatek,tphy.yaml

@@ -80,6 +80,8 @@ properties:
               - mediatek,mt2712-tphy
               - mediatek,mt7629-tphy
               - mediatek,mt8183-tphy
+              - mediatek,mt8186-tphy
+              - mediatek,mt8192-tphy
           - const: mediatek,generic-tphy-v2
       - items:
           - enum:

Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/phy-rockchip-naneng-combphy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Rockchip SoC Naneng Combo Phy Device Tree Bindings
+
+maintainers:
+  - Heiko Stuebner <heiko@sntech.de>
+
+properties:
+  compatible:
+    enum:
+      - rockchip,rk3568-naneng-combphy
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: reference clock
+      - description: apb clock
+      - description: pipe clock
+
+  clock-names:
+    items:
+      - const: ref
+      - const: apb
+      - const: pipe
+
+  resets:
+    items:
+      - description: exclusive PHY reset line
+
+  rockchip,enable-ssc:
+    type: boolean
+    description:
+      The option SSC can be enabled for U3, SATA and PCIE.
+      Most commercially available platforms use SSC to reduce EMI.
+
+  rockchip,ext-refclk:
+    type: boolean
+    description:
+      Many PCIe connections, especially backplane connections,
+      require a synchronous reference clock between the two link partners.
+      To achieve this a common clock source, referred to as REFCLK in
+      the PCI Express Card Electromechanical Specification,
+      should be used by both ends of the PCIe link.
+      In PCIe mode one can choose to use an internal or an external reference
+      clock.
+      By default the internal clock is selected. The PCIe PHY provides a 100MHz
+      differential clock output(optional with SSC) for system applications.
+      When selecting this option an externally 100MHz differential
+      reference clock needs to be provided to the PCIe PHY.
+
+  rockchip,pipe-grf:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Some additional phy settings are accessed through GRF regs.
+
+  rockchip,pipe-phy-grf:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Some additional pipe settings are accessed through GRF regs.
+
+  "#phy-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - resets
+  - rockchip,pipe-grf
+  - rockchip,pipe-phy-grf
+  - "#phy-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/rk3568-cru.h>
+
+    pipegrf: syscon@fdc50000 {
+      compatible = "rockchip,rk3568-pipe-grf", "syscon";
+      reg = <0xfdc50000 0x1000>;
+    };
+
+    pipe_phy_grf0: syscon@fdc70000 {
+      compatible = "rockchip,rk3568-pipe-phy-grf", "syscon";
+      reg = <0xfdc70000 0x1000>;
+    };
+
+    combphy0: phy@fe820000 {
+      compatible = "rockchip,rk3568-naneng-combphy";
+      reg = <0xfe820000 0x100>;
+      clocks = <&pmucru CLK_PCIEPHY0_REF>,
+               <&cru PCLK_PIPEPHY0>,
+               <&cru PCLK_PIPE>;
+      clock-names = "ref", "apb", "pipe";
+      assigned-clocks = <&pmucru CLK_PCIEPHY0_REF>;
+      assigned-clock-rates = <100000000>;
+      resets = <&cru SRST_PIPEPHY0>;
+      rockchip,pipe-grf = <&pipegrf>;
+      rockchip,pipe-phy-grf = <&pipe_phy_grf0>;
+      #phy-cells = <1>;
+    };

Documentation/devicetree/bindings/phy/qcom,edp-phy.yaml

@@ -16,7 +16,9 @@ description:
 
 properties:
   compatible:
-    const: qcom,sc8180x-edp-phy
+    enum:
+      - qcom,sc7280-edp-phy
+      - qcom,sc8180x-edp-phy
 
   reg:
     items:

Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml

@@ -32,6 +32,7 @@ properties:
       - qcom,sc8180x-qmp-pcie-phy
       - qcom,sc8180x-qmp-ufs-phy
       - qcom,sc8180x-qmp-usb3-phy
+      - qcom,sc8280xp-qmp-ufs-phy
       - qcom,sdm845-qhp-pcie-phy
       - qcom,sdm845-qmp-pcie-phy
       - qcom,sdm845-qmp-ufs-phy
@@ -280,6 +281,8 @@ allOf:
               - qcom,sdm845-qmp-ufs-phy
               - qcom,sm8150-qmp-ufs-phy
               - qcom,sm8250-qmp-ufs-phy
+              - qcom,sc8180x-qmp-ufs-phy
+              - qcom,sc8280xp-qmp-ufs-phy
     then:
       properties:
         clocks:

Documentation/devicetree/bindings/phy/qcom,qusb2-phy.yaml

@@ -19,6 +19,7 @@ properties:
       - items:
           - enum:
               - qcom,ipq8074-qusb2-phy
+              - qcom,msm8953-qusb2-phy
               - qcom,msm8996-qusb2-phy
               - qcom,msm8998-qusb2-phy
               - qcom,qcm2290-qusb2-phy

Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt

-Qualcomm's USB HS PHY
-
-PROPERTIES
-
-- compatible:
-    Usage: required
-    Value type: <string>
-    Definition: Should contain "qcom,usb-hs-phy" and more specifically one of the
-                following:
-
-                        "qcom,usb-hs-phy-apq8064"
-                        "qcom,usb-hs-phy-msm8916"
-                        "qcom,usb-hs-phy-msm8974"
-
-- #phy-cells:
-    Usage: required
-    Value type: <u32>
-    Definition: Should contain 0
-
-- clocks:
-    Usage: required
-    Value type: <prop-encoded-array>
-    Definition: Should contain clock specifier for the reference and sleep
-                clocks
-
-- clock-names:
-    Usage: required
-    Value type: <stringlist>
-    Definition: Should contain "ref" and "sleep" for the reference and sleep
-                clocks respectively
-
-- resets:
-    Usage: required
-    Value type: <prop-encoded-array>
-    Definition: Should contain the phy and POR resets
-
-- reset-names:
-    Usage: required
-    Value type: <stringlist>
-    Definition: Should contain "phy" and "por" for the phy and POR resets
-                respectively
-
-- v3p3-supply:
-    Usage: required
-    Value type: <phandle>
-    Definition: Should contain a reference to the 3.3V supply
-
-- v1p8-supply:
-    Usage: required
-    Value type: <phandle>
-    Definition: Should contain a reference to the 1.8V supply
-
-- extcon:
-    Usage: optional
-    Value type: <prop-encoded-array>
-    Definition: Should contain the vbus extcon
-
-- qcom,init-seq:
-    Usage: optional
-    Value type: <u8 array>
-    Definition: Should contain a sequence of ULPI address and value pairs to
-                program into the ULPI_EXT_VENDOR_SPECIFIC area. This is related
-                to Device Mode Eye Diagram test. The addresses are offsets
-                from the ULPI_EXT_VENDOR_SPECIFIC address, for example,
-                <0x1 0x53> would mean "write the value 0x53 to address 0x81".
-
-EXAMPLE
-
-otg: usb-controller {
-	ulpi {
-		phy {
-			compatible = "qcom,usb-hs-phy-msm8974", "qcom,usb-hs-phy";
-			#phy-cells = <0>;
-			clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
-			clock-names = "ref", "sleep";
-			resets = <&gcc GCC_USB2A_PHY_BCR>, <&otg 0>;
-			reset-names = "phy", "por";
-			v3p3-supply = <&pm8941_l24>;
-			v1p8-supply = <&pm8941_l6>;
-			extcon = <&smbb>;
-			qcom,init-seq = /bits/ 8 <0x1 0x63>;
-		};
-	};
-};

Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml

+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/qcom,usb-hs-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm's USB HS PHY binding description
+
+maintainers:
+  - Bjorn Andersson <bjorn.andersson@linaro.org>
+
+if:
+  properties:
+    compatible:
+      contains:
+        const: qcom,usb-hs-phy-apq8064
+  then:
+    properties:
+      resets:
+        maxItems: 1
+
+      reset-names:
+        const: por
+
+  else:
+    properties:
+      resets:
+        minItems: 2
+        maxItems: 2
+
+      reset-names:
+        items:
+          - const: phy
+          - const: por
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - qcom,usb-hs-phy-apq8064
+          - qcom,usb-hs-phy-msm8916
+          - qcom,usb-hs-phy-msm8974
+      - const: qcom,usb-hs-phy
+
+  clocks:
+    minItems: 2
+    maxItems: 2
+
+  clock-names:
+    maxItems: 2
+    contains:
+      items:
+        - const: ref
+        - const: sleep
+
+  resets: true
+
+  reset-names: true
+
+  v1p8-supply: true
+
+  v3p3-supply: true
+
+  extcon: true
+
+  "#phy-cells":
+    const: 0
+
+  qcom,init-seq:
+    $ref: /schemas/types.yaml#/definitions/uint8-matrix
+    description: >
+      Sequence of ULPI address and value pairs to
+      program into the ULPI_EXT_VENDOR_SPECIFIC area.
+      This is related to Device Mode Eye Diagram test.
+    maxItems: 32 # no hard limit
+    items:
+      items:
+        - description: >
+            the address is offset from the ULPI_EXT_VENDOR_SPECIFIC address
+        - description: value
+
+required:
+  - clocks
+  - clock-names
+  - resets
+  - reset-names
+  - "#phy-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    otg: usb-controller {
+      ulpi {
+        phy {
+          compatible = "qcom,usb-hs-phy-msm8974", "qcom,usb-hs-phy";
+          #phy-cells = <0>;
+          clocks = <&clk 0>, <&clk 258>;
+          clock-names = "ref", "sleep";
+          resets = <&gcc 10>, <&otg 0>;
+          reset-names = "phy", "por";
+          v3p3-supply = <&pm8941_l24>;
+          v1p8-supply = <&pm8941_l6>;
+          extcon = <&smbb>;
+          qcom,init-seq = /bits/ 8 <0x1 0x63>;
+        };
+      };
+    };

Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml

@@ -15,8 +15,11 @@ description: |
 properties:
   compatible:
     enum:
+      - qcom,usb-snps-hs-5nm-phy
       - qcom,usb-snps-hs-7nm-phy
       - qcom,sc7280-usb-hs-phy
+      - qcom,sc8180x-usb-hs-phy
+      - qcom,sc8280xp-usb-hs-phy
       - qcom,sm8150-usb-hs-phy
       - qcom,sm8250-usb-hs-phy
       - qcom,sm8350-usb-hs-phy

Documentation/devicetree/bindings/phy/renesas,usb2-phy.yaml

@@ -33,7 +33,8 @@ properties:
       - items:
           - enum:
               - renesas,usb2-phy-r9a07g044 # RZ/G2{L,LC}
-          - const: renesas,rzg2l-usb2-phy  # RZ/G2L family
+              - renesas,usb2-phy-r9a07g054 # RZ/V2L
+          - const: renesas,rzg2l-usb2-phy
 
   reg:
     maxItems: 1

Documentation/devicetree/bindings/phy/samsung,dp-video-phy.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/samsung,dp-video-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung Exynos SoC DisplayPort PHY
+
+maintainers:
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+  - Marek Szyprowski <m.szyprowski@samsung.com>
+  - Sylwester Nawrocki <s.nawrocki@samsung.com>
+
+properties:
+  compatible:
+    enum:
+      - samsung,exynos5250-dp-video-phy
+      - samsung,exynos5420-dp-video-phy
+
+  "#phy-cells":
+    const: 0
+
+  samsung,pmu-syscon:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Phandle to PMU system controller interface.
+
+required:
+  - compatible
+  - "#phy-cells"
+  - samsung,pmu-syscon
+
+additionalProperties: false
+
+examples:
+  - |
+    phy {
+        compatible = "samsung,exynos5420-dp-video-phy";
+        samsung,pmu-syscon = <&pmu_system_controller>;
+        #phy-cells = <0>;
+    };

Documentation/devicetree/bindings/phy/samsung,exynos5250-sata-phy.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/samsung,exynos5250-sata-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung Exynos5250 SoC SATA PHY
+
+maintainers:
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+  - Marek Szyprowski <m.szyprowski@samsung.com>
+  - Sylwester Nawrocki <s.nawrocki@samsung.com>
+
+properties:
+  compatible:
+    const: samsung,exynos5250-sata-phy
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    items:
+      - const: sata_phyctrl
+
+  "#phy-cells":
+    const: 0
+
+  reg:
+    maxItems: 1
+
+  samsung,syscon-phandle:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Phandle to PMU system controller interface.
+
+  samsung,exynos-sataphy-i2c-phandle:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Phandle to I2C SATA interface.
+
+required:
+  - compatible
+  - clocks
+  - clock-names
+  - "#phy-cells"
+  - reg
+  - samsung,syscon-phandle
+  - samsung,exynos-sataphy-i2c-phandle
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/exynos5250.h>
+
+    phy@12170000 {
+        compatible = "samsung,exynos5250-sata-phy";
+        reg = <0x12170000 0x1ff>;
+        clocks = <&clock CLK_SATA_PHYCTRL>;
+        clock-names = "sata_phyctrl";
+        #phy-cells = <0>;
+        samsung,syscon-phandle = <&pmu_system_controller>;
+        samsung,exynos-sataphy-i2c-phandle = <&sata_phy_i2c>;
+    };

Documentation/devicetree/bindings/phy/samsung,mipi-video-phy.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/samsung,mipi-video-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung S5P/Exynos SoC MIPI CSIS/DSIM DPHY
+
+maintainers:
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+  - Marek Szyprowski <m.szyprowski@samsung.com>
+  - Sylwester Nawrocki <s.nawrocki@samsung.com>
+
+description: |
+  For samsung,s5pv210-mipi-video-phy compatible PHYs the second cell in the
+  PHY specifier identifies the PHY and its meaning is as follows::
+    0 - MIPI CSIS 0,
+    1 - MIPI DSIM 0,
+    2 - MIPI CSIS 1,
+    3 - MIPI DSIM 1.
+
+  samsung,exynos5420-mipi-video-phy and samsung,exynos5433-mipi-video-phy
+  support additional fifth PHY::
+    4 - MIPI CSIS 2.
+
+properties:
+  compatible:
+    enum:
+      - samsung,s5pv210-mipi-video-phy
+      - samsung,exynos5420-mipi-video-phy
+      - samsung,exynos5433-mipi-video-phy
+
+  "#phy-cells":
+    const: 1
+
+  syscon:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Phandle to PMU system controller interface, valid only for
+      samsung,s5pv210-mipi-video-phy and samsung,exynos5420-mipi-video-phy.
+
+  samsung,pmu-syscon:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Phandle to PMU system controller interface, valid for
+      samsung,exynos5433-mipi-video-phy.
+
+  samsung,disp-sysreg:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Phandle to DISP system controller interface, valid for
+      samsung,exynos5433-mipi-video-phy.
+
+  samsung,cam0-sysreg:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Phandle to CAM0 system controller interface, valid for
+      samsung,exynos5433-mipi-video-phy.
+
+  samsung,cam1-sysreg:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Phandle to CAM1 system controller interface, valid for
+      samsung,exynos5433-mipi-video-phy.
+
+required:
+  - compatible
+  - "#phy-cells"
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - samsung,s5pv210-mipi-video-phy
+              - samsung,exynos5420-mipi-video-phy
+    then:
+      properties:
+        samsung,pmu-syscon: false
+        samsung,disp-sysreg: false
+        samsung,cam0-sysreg: false
+        samsung,cam1-sysreg: false
+      required:
+        - syscon
+    else:
+      properties:
+        syscon: false
+      required:
+        - samsung,pmu-syscon
+        - samsung,disp-sysreg
+        - samsung,cam0-sysreg
+        - samsung,cam1-sysreg
+
+additionalProperties: false
+
+examples:
+  - |
+    phy {
+        compatible = "samsung,exynos5433-mipi-video-phy";
+        #phy-cells = <1>;
+        samsung,pmu-syscon = <&pmu_system_controller>;
+        samsung,cam0-sysreg = <&syscon_cam0>;
+        samsung,cam1-sysreg = <&syscon_cam1>;
+        samsung,disp-sysreg = <&syscon_disp>;
+    };
+
+  - |
+    phy {
+        compatible = "samsung,s5pv210-mipi-video-phy";
+        syscon = <&pmu_system_controller>;
+        #phy-cells = <1>;
+    };

Documentation/devicetree/bindings/phy/samsung,usb2-phy.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/samsung,usb2-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung S5P/Exynos SoC USB 2.0 PHY
+
+maintainers:
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+  - Marek Szyprowski <m.szyprowski@samsung.com>
+  - Sylwester Nawrocki <s.nawrocki@samsung.com>
+
+description: |
+  The first phandle argument in the PHY specifier identifies the PHY, its
+  meaning is compatible dependent. For the currently supported SoCs (Exynos4210
+  and Exynos4212) it is as follows::
+    0 - USB device ("device"),
+    1 - USB host ("host"),
+    2 - HSIC0 ("hsic0"),
+    3 - HSIC1 ("hsic1"),
+  Exynos3250 has only USB device phy available as phy 0.
+
+  Exynos4210 and Exynos4212 use mode switching and require that mode switch
+  register is supplied.
+
+properties:
+  compatible:
+    enum:
+      - samsung,exynos3250-usb2-phy
+      - samsung,exynos4210-usb2-phy
+      - samsung,exynos4x12-usb2-phy
+      - samsung,exynos5250-usb2-phy
+      - samsung,exynos5420-usb2-phy
+      - samsung,s5pv210-usb2-phy
+
+  clocks:
+    items:
+      - description: PHY module gate clock.
+      - description: Reference rate clock of PHY module.
+
+  clock-names:
+    items:
+      - const: phy
+      - const: ref
+
+  "#phy-cells":
+    const: 1
+
+  reg:
+    maxItems: 1
+
+  samsung,pmureg-phandle:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Phandle to PMU system controller interface.
+
+  samsung,sysreg-phandle:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Phandle to system registers interface.
+
+  vbus-supply:
+    description:
+      VBUS power source.
+
+required:
+  - compatible
+  - clocks
+  - clock-names
+  - "#phy-cells"
+  - reg
+  - samsung,pmureg-phandle
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - samsung,exynos4x12-usb2-phy
+              - samsung,exynos5250-usb2-phy
+              - samsung,exynos5420-usb2-phy
+    then:
+      required:
+        - samsung,sysreg-phandle
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/exynos5420.h>
+
+    phy@12130000 {
+        compatible = "samsung,exynos5420-usb2-phy";
+        reg = <0x12130000 0x100>;
+        #phy-cells = <1>;
+        clocks = <&clock CLK_USBH20>, <&clock CLK_SCLK_USBPHY300>;
+        clock-names = "phy", "ref";
+        samsung,sysreg-phandle = <&sysreg_system_controller>;
+        samsung,pmureg-phandle = <&pmu_system_controller>;
+    };

Documentation/devicetree/bindings/phy/samsung,usb3-drd-phy.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/samsung,usb3-drd-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung Exynos SoC USB 3.0 DRD PHY USB 2.0 PHY
+
+maintainers:
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+  - Marek Szyprowski <m.szyprowski@samsung.com>
+  - Sylwester Nawrocki <s.nawrocki@samsung.com>
+
+description: |
+  For samsung,exynos5250-usbdrd-phy and samsung,exynos5420-usbdrd-phy
+  compatible PHYs, the second cell in the PHY specifier identifies the
+  PHY id, which is interpreted as follows::
+    0 - UTMI+ type phy,
+    1 - PIPE3 type phy.
+
+  For SoCs like Exynos5420 having multiple USB 3.0 DRD PHY controllers,
+  'usbdrd_phy' nodes should have numbered alias in the aliases node, in the
+  form of usbdrdphyN, N = 0, 1... (depending on number of controllers).
+
+properties:
+  compatible:
+    enum:
+      - samsung,exynos5250-usbdrd-phy
+      - samsung,exynos5420-usbdrd-phy
+      - samsung,exynos5433-usbdrd-phy
+      - samsung,exynos7-usbdrd-phy
+
+  clocks:
+    minItems: 2
+    maxItems: 5
+
+  clock-names:
+    minItems: 2
+    maxItems: 5
+    description: |
+      At least two clocks::
+        - Main PHY clock (same as USB DRD controller i.e. DWC3 IP clock), used
+          for register access.
+        - PHY reference clock (usually crystal clock), used for PHY operations,
+          associated by phy name. It is used to determine bit values for clock
+          settings register.  For Exynos5420 this is given as 'sclk_usbphy30'
+          in the CMU.
+
+  "#phy-cells":
+    const: 1
+
+  port:
+    $ref: /schemas/graph.yaml#/properties/port
+    description:
+      Any connector to the data bus of this controller should be modelled using
+      the OF graph bindings specified.
+
+  reg:
+    maxItems: 1
+
+  samsung,pmu-syscon:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Phandle to PMU system controller interface.
+
+  vbus-supply:
+    description:
+      VBUS power source.
+
+  vbus-boost-supply:
+    description:
+      VBUS Boost 5V power source.
+
+required:
+  - compatible
+  - clocks
+  - clock-names
+  - "#phy-cells"
+  - reg
+  - samsung,pmu-syscon
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - samsung,exynos5433-usbdrd-phy
+              - samsung,exynos7-usbdrd-phy
+    then:
+      properties:
+        clocks:
+          minItems: 5
+          maxItems: 5
+        clock-names:
+          items:
+            - const: phy
+            - const: ref
+            - const: phy_utmi
+            - const: phy_pipe
+            - const: itp
+    else:
+      properties:
+        clocks:
+          minItems: 2
+          maxItems: 2
+        clock-names:
+          items:
+            - const: phy
+            - const: ref
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/exynos5420.h>
+
+    phy@12100000 {
+        compatible = "samsung,exynos5420-usbdrd-phy";
+        reg = <0x12100000 0x100>;
+        #phy-cells = <1>;
+        clocks = <&clock CLK_USBD300>, <&clock CLK_SCLK_USBPHY300>;
+        clock-names = "phy", "ref";
+        samsung,pmu-syscon = <&pmu_system_controller>;
+        vbus-supply = <&usb300_vbus_reg>;
+    };

Documentation/devicetree/bindings/phy/samsung-phy.txt

-Samsung S5P/Exynos SoC series MIPI CSIS/DSIM DPHY
--------------------------------------------------
-
-Required properties:
-- compatible : should be one of the listed compatibles:
-	- "samsung,s5pv210-mipi-video-phy"
-	- "samsung,exynos5420-mipi-video-phy"
-	- "samsung,exynos5433-mipi-video-phy"
-- #phy-cells : from the generic phy bindings, must be 1;
-
-In case of s5pv210 and exynos5420 compatible PHYs:
-- syscon - phandle to the PMU system controller
-
-In case of exynos5433 compatible PHY:
- - samsung,pmu-syscon - phandle to the PMU system controller
- - samsung,disp-sysreg - phandle to the DISP system registers controller
- - samsung,cam0-sysreg - phandle to the CAM0 system registers controller
- - samsung,cam1-sysreg - phandle to the CAM1 system registers controller
-
-For "samsung,s5pv210-mipi-video-phy" compatible PHYs the second cell in
-the PHY specifier identifies the PHY and its meaning is as follows:
-  0 - MIPI CSIS 0,
-  1 - MIPI DSIM 0,
-  2 - MIPI CSIS 1,
-  3 - MIPI DSIM 1.
-"samsung,exynos5420-mipi-video-phy" and "samsung,exynos5433-mipi-video-phy"
-supports additional fifth PHY:
-  4 - MIPI CSIS 2.
-
-Samsung Exynos SoC series Display Port PHY
--------------------------------------------------
-
-Required properties:
-- compatible : should be one of the following supported values:
-	 - "samsung,exynos5250-dp-video-phy"
-	 - "samsung,exynos5420-dp-video-phy"
-- samsung,pmu-syscon: phandle for PMU system controller interface, used to
-		      control pmu registers for power isolation.
-- #phy-cells : from the generic PHY bindings, must be 0;
-
-Samsung S5P/Exynos SoC series USB PHY
--------------------------------------------------
-
-Required properties:
-- compatible : should be one of the listed compatibles:
-	- "samsung,exynos3250-usb2-phy"
-	- "samsung,exynos4210-usb2-phy"
-	- "samsung,exynos4x12-usb2-phy"
-	- "samsung,exynos5250-usb2-phy"
-	- "samsung,exynos5420-usb2-phy"
-	- "samsung,s5pv210-usb2-phy"
-- reg : a list of registers used by phy driver
-	- first and obligatory is the location of phy modules registers
-- samsung,sysreg-phandle - handle to syscon used to control the system registers
-- samsung,pmureg-phandle - handle to syscon used to control PMU registers
-- #phy-cells : from the generic phy bindings, must be 1;
-- clocks and clock-names:
-	- the "phy" clock is required by the phy module, used as a gate
-	- the "ref" clock is used to get the rate of the clock provided to the
-	  PHY module
-
-Optional properties:
-- vbus-supply: power-supply phandle for vbus power source
-
-The first phandle argument in the PHY specifier identifies the PHY, its
-meaning is compatible dependent. For the currently supported SoCs (Exynos 4210
-and Exynos 4212) it is as follows:
-  0 - USB device ("device"),
-  1 - USB host ("host"),
-  2 - HSIC0 ("hsic0"),
-  3 - HSIC1 ("hsic1"),
-Exynos3250 has only USB device phy available as phy 0.
-
-Exynos 4210 and Exynos 4212 use mode switching and require that mode switch
-register is supplied.
-
-Example:
-
-For Exynos 4412 (compatible with Exynos 4212):
-
-usbphy: phy@125b0000 {
-	compatible = "samsung,exynos4x12-usb2-phy";
-	reg = <0x125b0000 0x100>;
-	clocks = <&clock 305>, <&clock 2>;
-	clock-names = "phy", "ref";
-	#phy-cells = <1>;
-	samsung,sysreg-phandle = <&sys_reg>;
-	samsung,pmureg-phandle = <&pmu_reg>;
-};
-
-Then the PHY can be used in other nodes such as:
-
-phy-consumer@12340000 {
-	phys = <&usbphy 2>;
-	phy-names = "phy";
-};
-
-Refer to DT bindings documentation of particular PHY consumer devices for more
-information about required PHYs and the way of specification.
-
-Samsung SATA PHY Controller
----------------------------
-
-SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers.
-Each SATA PHY controller should have its own node.
-
-Required properties:
-- compatible        : compatible list, contains "samsung,exynos5250-sata-phy"
-- reg : offset and length of the SATA PHY register set;
-- #phy-cells : must be zero
-- clocks : must be exactly one entry
-- clock-names : must be "sata_phyctrl"
-- samsung,exynos-sataphy-i2c-phandle : a phandle to the I2C device, no arguments
-- samsung,syscon-phandle : a phandle to the PMU system controller, no arguments
-
-Example:
-	sata_phy: sata-phy@12170000 {
-		compatible = "samsung,exynos5250-sata-phy";
-		reg = <0x12170000 0x1ff>;
-		clocks = <&clock 287>;
-		clock-names = "sata_phyctrl";
-		#phy-cells = <0>;
-		samsung,exynos-sataphy-i2c-phandle = <&sata_phy_i2c>;
-		samsung,syscon-phandle = <&pmu_syscon>;
-	};
-
-Device-Tree bindings for sataphy i2c client driver
---------------------------------------------------
-
-Required properties:
-compatible: Should be "samsung,exynos-sataphy-i2c"
-- reg: I2C address of the sataphy i2c device.
-
-Example:
-
-	sata_phy_i2c:sata-phy@38 {
-		compatible = "samsung,exynos-sataphy-i2c";
-		reg = <0x38>;
-	};
-
-Samsung Exynos5 SoC series USB DRD PHY controller
---------------------------------------------------
-
-Required properties:
-- compatible : Should be set to one of the following supported values:
-	- "samsung,exynos5250-usbdrd-phy" - for exynos5250 SoC,
-	- "samsung,exynos5420-usbdrd-phy" - for exynos5420 SoC.
-	- "samsung,exynos5433-usbdrd-phy" - for exynos5433 SoC.
-	- "samsung,exynos7-usbdrd-phy" - for exynos7 SoC.
-- reg : Register offset and length of USB DRD PHY register set;
-- clocks: Clock IDs array as required by the controller
-- clock-names: names of clocks correseponding to IDs in the clock property;
-	       Required clocks:
-	- phy: main PHY clock (same as USB DRD controller i.e. DWC3 IP clock),
-	       used for register access.
-	- ref: PHY's reference clock (usually crystal clock), used for
-	       PHY operations, associated by phy name. It is used to
-	       determine bit values for clock settings register.
-	       For Exynos5420 this is given as 'sclk_usbphy30' in CMU.
-	- optional clocks: Exynos5433 & Exynos7 SoC has now following additional
-			   gate clocks available:
-			   - phy_pipe: for PIPE3 phy
-			   - phy_utmi: for UTMI+ phy
-			   - itp: for ITP generation
-- samsung,pmu-syscon: phandle for PMU system controller interface, used to
-		      control pmu registers for power isolation.
-- #phy-cells : from the generic PHY bindings, must be 1;
-
-For "samsung,exynos5250-usbdrd-phy" and "samsung,exynos5420-usbdrd-phy"
-compatible PHYs, the second cell in the PHY specifier identifies the
-PHY id, which is interpreted as follows:
-  0 - UTMI+ type phy,
-  1 - PIPE3 type phy,
-
-Example:
-	usbdrd_phy: usbphy@12100000 {
-		compatible = "samsung,exynos5250-usbdrd-phy";
-		reg = <0x12100000 0x100>;
-		clocks = <&clock 286>, <&clock 1>;
-		clock-names = "phy", "ref";
-		samsung,pmu-syscon = <&pmu_system_controller>;
-		#phy-cells = <1>;
-	};
-
-- aliases: For SoCs like Exynos5420 having multiple USB 3.0 DRD PHY controllers,
-	   'usbdrd_phy' nodes should have numbered alias in the aliases node,
-	   in the form of usbdrdphyN, N = 0, 1... (depending on number of
-	   controllers).
-Example:
-	aliases {
-		usbdrdphy0 = &usb3_phy0;
-		usbdrdphy1 = &usb3_phy1;
-	};
-
-Samsung Exynos SoC series PCIe PHY controller
---------------------------------------------------
-Required properties:
-- compatible : Should be set to "samsung,exynos5440-pcie-phy"
-- #phy-cells : Must be zero
-- reg : a register used by phy driver.
-	- First is for phy register, second is for block register.
-- reg-names : Must be set to "phy" and "block".
-
-Example:
-	pcie_phy0: pcie-phy@270000 {
-		#phy-cells = <0>;
-		compatible = "samsung,exynos5440-pcie-phy";
-		reg = <0x270000 0x1000>, <0x271000 0x40>;
-		reg-names = "phy", "block";
-	};

Documentation/devicetree/bindings/trivial-devices.yaml

@@ -283,6 +283,8 @@ properties:
           - renesas,isl29501
             # S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power)
           - samsung,24ad0xd1
+            # Samsung Exynos SoC SATA PHY I2C device
+          - samsung,exynos-sataphy-i2c
             # Sensirion low power multi-pixel gas sensor with I2C interface
           - sensirion,sgpc3
             # Sensirion multi-pixel gas sensor with I2C interface

MAINTAINERS

@@ -17182,7 +17182,7 @@ SAMSUNG USB2 PHY DRIVER
 M:	Sylwester Nawrocki <s.nawrocki@samsung.com>
 L:	linux-kernel@vger.kernel.org
 S:	Supported
-F:	Documentation/devicetree/bindings/phy/samsung-phy.txt
+F:	Documentation/devicetree/bindings/phy/samsung,usb2-phy.yaml
 F:	Documentation/driver-api/phy/samsung-usb2.rst
 F:	drivers/phy/samsung/phy-exynos4210-usb2.c
 F:	drivers/phy/samsung/phy-exynos4x12-usb2.c

drivers/ata/ahci.h

@@ -240,8 +240,6 @@ enum {
 							as default lpm_policy */
 	AHCI_HFLAG_SUSPEND_PHYS		= (1 << 26), /* handle PHYs during
 							suspend/resume */
-	AHCI_HFLAG_IGN_NOTSUPP_POWER_ON	= (1 << 27), /* ignore -EOPNOTSUPP
-							from phy_power_on() */
 	AHCI_HFLAG_NO_SXS		= (1 << 28), /* SXS not supported */
 
 	/* ap->flags bits */

drivers/ata/ahci_mvebu.c

@@ -227,7 +227,7 @@ static const struct ahci_mvebu_plat_data ahci_mvebu_armada_380_plat_data = {
 
 static const struct ahci_mvebu_plat_data ahci_mvebu_armada_3700_plat_data = {
 	.plat_config = ahci_mvebu_armada_3700_config,
-	.flags = AHCI_HFLAG_SUSPEND_PHYS | AHCI_HFLAG_IGN_NOTSUPP_POWER_ON,
+	.flags = AHCI_HFLAG_SUSPEND_PHYS,
 };
 
 static const struct of_device_id ahci_mvebu_of_match[] = {

drivers/ata/libahci_platform.c

@@ -59,7 +59,7 @@ int ahci_platform_enable_phys(struct ahci_host_priv *hpriv)
 		}
 
 		rc = phy_power_on(hpriv->phys[i]);
-		if (rc && !(rc == -EOPNOTSUPP && (hpriv->flags & AHCI_HFLAG_IGN_NOTSUPP_POWER_ON))) {
+		if (rc) {
 			phy_exit(hpriv->phys[i]);
 			goto disable_phys;
 		}

drivers/pci/controller/pci-aardvark.c

@@ -1482,9 +1482,7 @@ static int advk_pcie_enable_phy(struct advk_pcie *pcie)
 	}
 
 	ret = phy_power_on(pcie->phy);
-	if (ret == -EOPNOTSUPP) {
-		dev_warn(&pcie->pdev->dev, "PHY unsupported by firmware\n");
-	} else if (ret) {
+	if (ret) {
 		phy_exit(pcie->phy);
 		return ret;
 	}

drivers/phy/allwinner/phy-sun4i-usb.c

@@ -43,7 +43,7 @@
 #define REG_PHYCTL_A33			0x10
 #define REG_PHY_OTGCTL			0x20
 
-#define REG_PMU_UNK1			0x10
+#define REG_HCI_PHY_CTL			0x10
 
 #define PHYCTL_DATA			BIT(7)
 
@@ -82,6 +82,7 @@
 /* A83T specific control bits for PHY0 */
 #define PHY_CTL_VBUSVLDEXT		BIT(5)
 #define PHY_CTL_SIDDQ			BIT(3)
+#define PHY_CTL_H3_SIDDQ		BIT(1)
 
 /* A83T specific control bits for PHY2 HSIC */
 #define SUNXI_EHCI_HS_FORCE		BIT(20)
@@ -115,9 +116,9 @@ struct sun4i_usb_phy_cfg {
 	int hsic_index;
 	enum sun4i_usb_phy_type type;
 	u32 disc_thresh;
+	u32 hci_phy_ctl_clear;
 	u8 phyctl_offset;
 	bool dedicated_clocks;
-	bool enable_pmu_unk1;
 	bool phy0_dual_route;
 	int missing_phys;
 };
@@ -288,6 +289,12 @@ static int sun4i_usb_phy_init(struct phy *_phy)
 		return ret;
 	}
 
+	if (phy->pmu && data->cfg->hci_phy_ctl_clear) {
+		val = readl(phy->pmu + REG_HCI_PHY_CTL);
+		val &= ~data->cfg->hci_phy_ctl_clear;
+		writel(val, phy->pmu + REG_HCI_PHY_CTL);
+	}
+
 	if (data->cfg->type == sun8i_a83t_phy ||
 	    data->cfg->type == sun50i_h6_phy) {
 		if (phy->index == 0) {
@@ -297,11 +304,6 @@ static int sun4i_usb_phy_init(struct phy *_phy)
 			writel(val, data->base + data->cfg->phyctl_offset);
 		}
 	} else {
-		if (phy->pmu && data->cfg->enable_pmu_unk1) {
-			val = readl(phy->pmu + REG_PMU_UNK1);
-			writel(val & ~2, phy->pmu + REG_PMU_UNK1);
-		}
-
 		/* Enable USB 45 Ohm resistor calibration */
 		if (phy->index == 0)
 			sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN, 0x01, 1);
@@ -863,7 +865,6 @@ static const struct sun4i_usb_phy_cfg sun4i_a10_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = false,
-	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = {
@@ -872,7 +873,6 @@ static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = {
 	.disc_thresh = 2,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = false,
-	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = {
@@ -881,7 +881,6 @@ static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = {
@@ -890,7 +889,6 @@ static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = {
 	.disc_thresh = 2,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = false,
-	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = {
@@ -899,7 +897,6 @@ static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
@@ -908,7 +905,6 @@ static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A33,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun8i_a83t_cfg = {
@@ -925,7 +921,7 @@ static const struct sun4i_usb_phy_cfg sun8i_h3_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A33,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = true,
+	.hci_phy_ctl_clear = PHY_CTL_H3_SIDDQ,
 	.phy0_dual_route = true,
 };
 
@@ -935,7 +931,7 @@ static const struct sun4i_usb_phy_cfg sun8i_r40_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A33,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = true,
+	.hci_phy_ctl_clear = PHY_CTL_H3_SIDDQ,
 	.phy0_dual_route = true,
 };
 
@@ -945,7 +941,16 @@ static const struct sun4i_usb_phy_cfg sun8i_v3s_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A33,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = true,
+	.hci_phy_ctl_clear = PHY_CTL_H3_SIDDQ,
+	.phy0_dual_route = true,
+};
+
+static const struct sun4i_usb_phy_cfg sun20i_d1_cfg = {
+	.num_phys = 2,
+	.type = sun50i_h6_phy,
+	.phyctl_offset = REG_PHYCTL_A33,
+	.dedicated_clocks = true,
+	.hci_phy_ctl_clear = PHY_CTL_SIDDQ,
 	.phy0_dual_route = true,
 };
 
@@ -955,14 +960,13 @@ static const struct sun4i_usb_phy_cfg sun50i_a64_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A33,
 	.dedicated_clocks = true,
-	.enable_pmu_unk1 = true,
+	.hci_phy_ctl_clear = PHY_CTL_H3_SIDDQ,
 	.phy0_dual_route = true,
 };
 
 static const struct sun4i_usb_phy_cfg sun50i_h6_cfg = {
 	.num_phys = 4,
 	.type = sun50i_h6_phy,
-	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A33,
 	.dedicated_clocks = true,
 	.phy0_dual_route = true,
@@ -980,6 +984,7 @@ static const struct of_device_id sun4i_usb_phy_of_match[] = {
 	{ .compatible = "allwinner,sun8i-h3-usb-phy", .data = &sun8i_h3_cfg },
 	{ .compatible = "allwinner,sun8i-r40-usb-phy", .data = &sun8i_r40_cfg },
 	{ .compatible = "allwinner,sun8i-v3s-usb-phy", .data = &sun8i_v3s_cfg },
+	{ .compatible = "allwinner,sun20i-d1-usb-phy", .data = &sun20i_d1_cfg },
 	{ .compatible = "allwinner,sun50i-a64-usb-phy",
 	  .data = &sun50i_a64_cfg},
 	{ .compatible = "allwinner,sun50i-h6-usb-phy", .data = &sun50i_h6_cfg },

drivers/phy/amlogic/phy-meson-gxl-usb2.c

@@ -114,8 +114,10 @@ static int phy_meson_gxl_usb2_init(struct phy *phy)
 		return ret;
 
 	ret = clk_prepare_enable(priv->clk);
-	if (ret)
+	if (ret) {
+		reset_control_rearm(priv->reset);
 		return ret;
+	}
 
 	return 0;
 }
@@ -125,6 +127,7 @@ static int phy_meson_gxl_usb2_exit(struct phy *phy)
 	struct phy_meson_gxl_usb2_priv *priv = phy_get_drvdata(phy);
 
 	clk_disable_unprepare(priv->clk);
+	reset_control_rearm(priv->reset);
 
 	return 0;
 }

drivers/phy/amlogic/phy-meson8b-usb2.c

@@ -154,6 +154,7 @@ static int phy_meson8b_usb2_power_on(struct phy *phy)
 	ret = clk_prepare_enable(priv->clk_usb_general);
 	if (ret) {
 		dev_err(&phy->dev, "Failed to enable USB general clock\n");
+		reset_control_rearm(priv->reset);
 		return ret;
 	}
 
@@ -161,6 +162,7 @@ static int phy_meson8b_usb2_power_on(struct phy *phy)
 	if (ret) {
 		dev_err(&phy->dev, "Failed to enable USB DDR clock\n");
 		clk_disable_unprepare(priv->clk_usb_general);
+		reset_control_rearm(priv->reset);
 		return ret;
 	}
 
@@ -199,6 +201,7 @@ static int phy_meson8b_usb2_power_on(struct phy *phy)
 				dev_warn(&phy->dev, "USB ID detect failed!\n");
 				clk_disable_unprepare(priv->clk_usb);
 				clk_disable_unprepare(priv->clk_usb_general);
+				reset_control_rearm(priv->reset);
 				return -EINVAL;
 			}
 		}
@@ -218,6 +221,7 @@ static int phy_meson8b_usb2_power_off(struct phy *phy)
 
 	clk_disable_unprepare(priv->clk_usb);
 	clk_disable_unprepare(priv->clk_usb_general);
+	reset_control_rearm(priv->reset);
 
 	/* power off the PHY by putting it into reset mode */
 	regmap_update_bits(priv->regmap, REG_CTRL, REG_CTRL_POWER_ON_RESET,
@@ -265,8 +269,9 @@ static int phy_meson8b_usb2_probe(struct platform_device *pdev)
 		return PTR_ERR(priv->clk_usb);
 
 	priv->reset = devm_reset_control_get_optional_shared(&pdev->dev, NULL);
-	if (PTR_ERR(priv->reset) == -EPROBE_DEFER)
-		return PTR_ERR(priv->reset);
+	if (IS_ERR(priv->reset))
+		return dev_err_probe(&pdev->dev, PTR_ERR(priv->reset),
+				     "Failed to get the reset line");
 
 	priv->dr_mode = of_usb_get_dr_mode_by_phy(pdev->dev.of_node, -1);
 	if (priv->dr_mode == USB_DR_MODE_UNKNOWN) {

drivers/phy/broadcom/phy-brcm-usb-init-synopsys.c

@@ -47,6 +47,8 @@
 #define   USB_CTRL_USB_PM_SOFT_RESET_MASK		0x40000000
 #define   USB_CTRL_USB_PM_BDC_SOFT_RESETB_MASK		0x00800000
 #define   USB_CTRL_USB_PM_XHC_SOFT_RESETB_MASK		0x00400000
+#define   USB_CTRL_USB_PM_XHC_PME_EN_MASK		0x00000010
+#define   USB_CTRL_USB_PM_XHC_S2_CLK_SWITCH_EN_MASK	0x00000008
 #define USB_CTRL_USB_PM_STATUS		0x08
 #define USB_CTRL_USB_DEVICE_CTL1	0x10
 #define   USB_CTRL_USB_DEVICE_CTL1_PORT_MODE_MASK	0x00000003
@@ -190,10 +192,6 @@ static void usb_init_common(struct brcm_usb_init_params *params)
 
 	pr_debug("%s\n", __func__);
 
-	USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN);
-	/* 1 millisecond - for USB clocks to settle down */
-	usleep_range(1000, 2000);
-
 	if (USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE)) {
 		reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
 		reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
@@ -222,6 +220,17 @@ static void usb_wake_enable_7211b0(struct brcm_usb_init_params *params,
 		USB_CTRL_UNSET(ctrl, CTLR_CSHCR, ctl_pme_en);
 }
 
+static void usb_wake_enable_7216(struct brcm_usb_init_params *params,
+				 bool enable)
+{
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
+
+	if (enable)
+		USB_CTRL_SET(ctrl, USB_PM, XHC_PME_EN);
+	else
+		USB_CTRL_UNSET(ctrl, USB_PM, XHC_PME_EN);
+}
+
 static void usb_init_common_7211b0(struct brcm_usb_init_params *params)
 {
 	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
@@ -295,6 +304,20 @@ static void usb_init_common_7211b0(struct brcm_usb_init_params *params)
 	usb2_eye_fix_7211b0(params);
 }
 
+static void usb_init_common_7216(struct brcm_usb_init_params *params)
+{
+	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
+
+	USB_CTRL_UNSET(ctrl, USB_PM, XHC_S2_CLK_SWITCH_EN);
+	USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN);
+
+	/* 1 millisecond - for USB clocks to settle down */
+	usleep_range(1000, 2000);
+
+	usb_wake_enable_7216(params, false);
+	usb_init_common(params);
+}
+
 static void usb_init_xhci(struct brcm_usb_init_params *params)
 {
 	pr_debug("%s\n", __func__);
@@ -302,14 +325,20 @@ static void usb_init_xhci(struct brcm_usb_init_params *params)
 	xhci_soft_reset(params, 0);
 }
 
-static void usb_uninit_common(struct brcm_usb_init_params *params)
+static void usb_uninit_common_7216(struct brcm_usb_init_params *params)
 {
 	void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
 
 	pr_debug("%s\n", __func__);
 
+	if (!params->wake_enabled) {
 		USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN);
 
+		/* Switch to using slower clock during suspend to save power */
+		USB_CTRL_SET(ctrl, USB_PM, XHC_S2_CLK_SWITCH_EN);
+	} else {
+		usb_wake_enable_7216(params, true);
+	}
 }
 
 static void usb_uninit_common_7211b0(struct brcm_usb_init_params *params)
@@ -371,9 +400,9 @@ static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
 
 static const struct brcm_usb_init_ops bcm7216_ops = {
 	.init_ipp = usb_init_ipp,
-	.init_common = usb_init_common,
+	.init_common = usb_init_common_7216,
 	.init_xhci = usb_init_xhci,
-	.uninit_common = usb_uninit_common,
+	.uninit_common = usb_uninit_common_7216,
 	.uninit_xhci = usb_uninit_xhci,
 	.get_dual_select = usb_get_dual_select,
 	.set_dual_select = usb_set_dual_select,
@@ -396,6 +425,7 @@ void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params)
 
 	params->family_name = "7216";
 	params->ops = &bcm7216_ops;
+	params->suspend_with_clocks = true;
 }
 
 void brcm_usb_dvr_init_7211b0(struct brcm_usb_init_params *params)

drivers/phy/broadcom/phy-brcm-usb-init.c

@@ -79,6 +79,7 @@
 
 enum brcm_family_type {
 	BRCM_FAMILY_3390A0,
+	BRCM_FAMILY_4908,
 	BRCM_FAMILY_7250B0,
 	BRCM_FAMILY_7271A0,
 	BRCM_FAMILY_7364A0,
@@ -96,6 +97,7 @@ enum brcm_family_type {
 
 static const char *family_names[BRCM_FAMILY_COUNT] = {
 	USB_BRCM_FAMILY(3390A0),
+	USB_BRCM_FAMILY(4908),
 	USB_BRCM_FAMILY(7250B0),
 	USB_BRCM_FAMILY(7271A0),
 	USB_BRCM_FAMILY(7364A0),
@@ -203,6 +205,27 @@ usb_reg_bits_map_table[BRCM_FAMILY_COUNT][USB_CTRL_SELECTOR_COUNT] = {
 		USB_CTRL_USB_PM_USB20_HC_RESETB_VAR_MASK,
 		ENDIAN_SETTINGS, /* USB_CTRL_SETUP ENDIAN bits */
 	},
+	/* 4908 */
+	[BRCM_FAMILY_4908] = {
+		0, /* USB_CTRL_SETUP_SCB1_EN_MASK */
+		0, /* USB_CTRL_SETUP_SCB2_EN_MASK */
+		0, /* USB_CTRL_SETUP_SS_EHCI64BIT_EN_MASK */
+		0, /* USB_CTRL_SETUP_STRAP_IPP_SEL_MASK */
+		0, /* USB_CTRL_SETUP_OC3_DISABLE_MASK */
+		0, /* USB_CTRL_PLL_CTL_PLL_IDDQ_PWRDN_MASK */
+		0, /* USB_CTRL_USB_PM_BDC_SOFT_RESETB_MASK */
+		USB_CTRL_USB_PM_XHC_SOFT_RESETB_MASK,
+		USB_CTRL_USB_PM_USB_PWRDN_MASK,
+		0, /* USB_CTRL_USB30_CTL1_XHC_SOFT_RESETB_MASK */
+		0, /* USB_CTRL_USB30_CTL1_USB3_IOC_MASK */
+		0, /* USB_CTRL_USB30_CTL1_USB3_IPP_MASK */
+		0, /* USB_CTRL_USB_DEVICE_CTL1_PORT_MODE_MASK */
+		0, /* USB_CTRL_USB_PM_SOFT_RESET_MASK */
+		0, /* USB_CTRL_SETUP_CC_DRD_MODE_ENABLE_MASK */
+		0, /* USB_CTRL_SETUP_STRAP_CC_DRD_MODE_ENABLE_SEL_MASK */
+		0, /* USB_CTRL_USB_PM_USB20_HC_RESETB_VAR_MASK */
+		0, /* USB_CTRL_SETUP ENDIAN bits */
+	},
 	/* 7250b0 */
 	[BRCM_FAMILY_7250B0] = {
 		USB_CTRL_SETUP_SCB1_EN_MASK,
@@ -559,6 +582,7 @@ static void brcmusb_usb3_pll_54mhz(struct brcm_usb_init_params *params)
 	 */
 	switch (params->selected_family) {
 	case BRCM_FAMILY_3390A0:
+	case BRCM_FAMILY_4908:
 	case BRCM_FAMILY_7250B0:
 	case BRCM_FAMILY_7366C0:
 	case BRCM_FAMILY_74371A0:
@@ -1004,6 +1028,18 @@ static const struct brcm_usb_init_ops bcm7445_ops = {
 	.set_dual_select = usb_set_dual_select,
 };
 
+void brcm_usb_dvr_init_4908(struct brcm_usb_init_params *params)
+{
+	int fam;
+
+	fam = BRCM_FAMILY_4908;
+	params->selected_family = fam;
+	params->usb_reg_bits_map =
+		&usb_reg_bits_map_table[fam][0];
+	params->family_name = family_names[fam];
+	params->ops = &bcm7445_ops;
+}
+
 void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params)
 {
 	int fam;

drivers/phy/broadcom/phy-brcm-usb-init.h

@@ -64,6 +64,7 @@ struct  brcm_usb_init_params {
 	bool suspend_with_clocks;
 };
 
+void brcm_usb_dvr_init_4908(struct brcm_usb_init_params *params);
 void brcm_usb_dvr_init_7445(struct brcm_usb_init_params *params);
 void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params);
 void brcm_usb_dvr_init_7211b0(struct brcm_usb_init_params *params);

drivers/phy/broadcom/phy-brcm-usb.c

@@ -283,6 +283,15 @@ static const struct attribute_group brcm_usb_phy_group = {
 	.attrs = brcm_usb_phy_attrs,
 };
 
+static const struct match_chip_info chip_info_4908 = {
+	.init_func = &brcm_usb_dvr_init_4908,
+	.required_regs = {
+		BRCM_REGS_CTRL,
+		BRCM_REGS_XHCI_EC,
+		-1,
+	},
+};
+
 static const struct match_chip_info chip_info_7216 = {
 	.init_func = &brcm_usb_dvr_init_7216,
 	.required_regs = {
@@ -318,7 +327,7 @@ static const struct match_chip_info chip_info_7445 = {
 static const struct of_device_id brcm_usb_dt_ids[] = {
 	{
 		.compatible = "brcm,bcm4908-usb-phy",
-		.data = &chip_info_7445,
+		.data = &chip_info_4908,
 	},
 	{
 		.compatible = "brcm,bcm7216-usb-phy",

drivers/phy/cadence/Kconfig

@@ -22,6 +22,14 @@ config PHY_CADENCE_DPHY
 	  system. If M is selected, the module will be called
 	  cdns-dphy.
 
+config PHY_CADENCE_DPHY_RX
+	tristate "Cadence D-PHY Rx Support"
+	depends on HAS_IOMEM && OF
+	select GENERIC_PHY
+	select GENERIC_PHY_MIPI_DPHY
+	help
+	  Support for Cadence D-PHY in Rx configuration.
+
 config PHY_CADENCE_SIERRA
 	tristate "Cadence Sierra PHY Driver"
 	depends on OF && HAS_IOMEM && RESET_CONTROLLER

drivers/phy/cadence/Makefile

 # SPDX-License-Identifier: GPL-2.0-only
 obj-$(CONFIG_PHY_CADENCE_TORRENT)	+= phy-cadence-torrent.o
 obj-$(CONFIG_PHY_CADENCE_DPHY)	+= cdns-dphy.o
+obj-$(CONFIG_PHY_CADENCE_DPHY_RX)	+= cdns-dphy-rx.o
 obj-$(CONFIG_PHY_CADENCE_SIERRA)	+= phy-cadence-sierra.o
 obj-$(CONFIG_PHY_CADENCE_SALVO)	+= phy-cadence-salvo.o

drivers/phy/cadence/cdns-dphy-rx.c

+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+#include <linux/phy/phy-mipi-dphy.h>
+#include <linux/platform_device.h>
+
+#define DPHY_PMA_CMN(reg)		(reg)
+#define DPHY_PCS(reg)			(0xb00 + (reg))
+#define DPHY_ISO(reg)			(0xc00 + (reg))
+
+#define DPHY_CMN_SSM			DPHY_PMA_CMN(0x20)
+#define DPHY_CMN_RX_MODE_EN		BIT(10)
+#define DPHY_CMN_RX_BANDGAP_TIMER_MASK	GENMASK(8, 1)
+#define DPHY_CMN_SSM_EN			BIT(0)
+
+#define DPHY_CMN_RX_BANDGAP_TIMER	0x14
+
+#define DPHY_BAND_CFG			DPHY_PCS(0x0)
+#define DPHY_BAND_CFG_RIGHT_BAND	GENMASK(9, 5)
+#define DPHY_BAND_CFG_LEFT_BAND		GENMASK(4, 0)
+
+#define DPHY_POWER_ISLAND_EN_DATA	DPHY_PCS(0x8)
+#define DPHY_POWER_ISLAND_EN_DATA_VAL	0xaaaaaaaa
+
+#define DPHY_POWER_ISLAND_EN_CLK	DPHY_PCS(0xc)
+#define DPHY_POWER_ISLAND_EN_CLK_VAL	0xaa
+
+#define DPHY_ISO_CL_CTRL_L		DPHY_ISO(0x10)
+#define DPHY_ISO_DL_CTRL_L0		DPHY_ISO(0x14)
+#define DPHY_ISO_DL_CTRL_L1		DPHY_ISO(0x20)
+#define DPHY_ISO_DL_CTRL_L2		DPHY_ISO(0x30)
+#define DPHY_ISO_DL_CTRL_L3		DPHY_ISO(0x3c)
+
+#define DPHY_ISO_LANE_READY_BIT		0
+#define DPHY_ISO_LANE_READY_TIMEOUT_MS	100UL
+
+#define DPHY_LANES_MIN			1
+#define DPHY_LANES_MAX			4
+
+struct cdns_dphy_rx {
+	void __iomem *regs;
+	struct device *dev;
+	struct phy *phy;
+};
+
+struct cdns_dphy_rx_band {
+	/* Rates are in Mbps. */
+	unsigned int min_rate;
+	unsigned int max_rate;
+};
+
+/* Order of bands is important since the index is the band number. */
+static const struct cdns_dphy_rx_band bands[] = {
+	{ 80, 100 }, { 100, 120 }, { 120, 160 }, { 160, 200 }, { 200, 240 },
+	{ 240, 280 }, { 280, 320 }, { 320, 360 }, { 360, 400 }, { 400, 480 },
+	{ 480, 560 }, { 560, 640 }, { 640, 720 }, { 720, 800 }, { 800, 880 },
+	{ 880, 1040 }, { 1040, 1200 }, { 1200, 1350 }, { 1350, 1500 },
+	{ 1500, 1750 }, { 1750, 2000 }, { 2000, 2250 }, { 2250, 2500 }
+};
+
+static int cdns_dphy_rx_power_on(struct phy *phy)
+{
+	struct cdns_dphy_rx *dphy = phy_get_drvdata(phy);
+
+	/* Start RX state machine. */
+	writel(DPHY_CMN_SSM_EN | DPHY_CMN_RX_MODE_EN |
+	       FIELD_PREP(DPHY_CMN_RX_BANDGAP_TIMER_MASK,
+			  DPHY_CMN_RX_BANDGAP_TIMER),
+	       dphy->regs + DPHY_CMN_SSM);
+
+	return 0;
+}
+
+static int cdns_dphy_rx_power_off(struct phy *phy)
+{
+	struct cdns_dphy_rx *dphy = phy_get_drvdata(phy);
+
+	writel(0, dphy->regs + DPHY_CMN_SSM);
+
+	return 0;
+}
+
+static int cdns_dphy_rx_get_band_ctrl(unsigned long hs_clk_rate)
+{
+	unsigned int rate, i;
+
+	rate = hs_clk_rate / 1000000UL;
+	/* Since CSI-2 clock is DDR, the bit rate is twice the clock rate. */
+	rate *= 2;
+
+	if (rate < bands[0].min_rate)
+		return -EOPNOTSUPP;
+
+	for (i = 0; i < ARRAY_SIZE(bands); i++)
+		if (rate < bands[i].max_rate)
+			return i;
+
+	return -EOPNOTSUPP;
+}
+
+static inline int cdns_dphy_rx_wait_for_bit(void __iomem *addr,
+					    unsigned int bit)
+{
+	u32 val;
+
+	return readl_relaxed_poll_timeout(addr, val, val & BIT(bit), 10,
+					  DPHY_ISO_LANE_READY_TIMEOUT_MS * 1000);
+}
+
+static int cdns_dphy_rx_wait_lane_ready(struct cdns_dphy_rx *dphy,
+					unsigned int lanes)
+{
+	static const u32 data_lane_ctrl[] = {DPHY_ISO_DL_CTRL_L0,
+					     DPHY_ISO_DL_CTRL_L1,
+					     DPHY_ISO_DL_CTRL_L2,
+					     DPHY_ISO_DL_CTRL_L3};
+	void __iomem *reg = dphy->regs;
+	unsigned int i;
+	int ret;
+
+	/* Clock lane */
+	ret = cdns_dphy_rx_wait_for_bit(reg + DPHY_ISO_CL_CTRL_L,
+					DPHY_ISO_LANE_READY_BIT);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < lanes; i++) {
+		ret = cdns_dphy_rx_wait_for_bit(reg + data_lane_ctrl[i],
+						DPHY_ISO_LANE_READY_BIT);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int cdns_dphy_rx_configure(struct phy *phy,
+				  union phy_configure_opts *opts)
+{
+	struct cdns_dphy_rx *dphy = phy_get_drvdata(phy);
+	unsigned int reg, lanes = opts->mipi_dphy.lanes;
+	int band_ctrl, ret;
+
+	/* Data lanes. Minimum one lane is mandatory. */
+	if (lanes < DPHY_LANES_MIN || lanes > DPHY_LANES_MAX)
+		return -EINVAL;
+
+	band_ctrl = cdns_dphy_rx_get_band_ctrl(opts->mipi_dphy.hs_clk_rate);
+	if (band_ctrl < 0)
+		return band_ctrl;
+
+	reg = FIELD_PREP(DPHY_BAND_CFG_LEFT_BAND, band_ctrl) |
+	      FIELD_PREP(DPHY_BAND_CFG_RIGHT_BAND, band_ctrl);
+	writel(reg, dphy->regs + DPHY_BAND_CFG);
+
+	/*
+	 * Set the required power island phase 2 time. This is mandated by DPHY
+	 * specs.
+	 */
+	reg = DPHY_POWER_ISLAND_EN_DATA_VAL;
+	writel(reg, dphy->regs + DPHY_POWER_ISLAND_EN_DATA);
+	reg = DPHY_POWER_ISLAND_EN_CLK_VAL;
+	writel(reg, dphy->regs + DPHY_POWER_ISLAND_EN_CLK);
+
+	ret = cdns_dphy_rx_wait_lane_ready(dphy, lanes);
+	if (ret) {
+		dev_err(dphy->dev, "DPHY wait for lane ready timeout\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int cdns_dphy_rx_validate(struct phy *phy, enum phy_mode mode,
+				 int submode, union phy_configure_opts *opts)
+{
+	int ret;
+
+	if (mode != PHY_MODE_MIPI_DPHY)
+		return -EINVAL;
+
+	ret = cdns_dphy_rx_get_band_ctrl(opts->mipi_dphy.hs_clk_rate);
+	if (ret < 0)
+		return ret;
+
+	return phy_mipi_dphy_config_validate(&opts->mipi_dphy);
+}
+
+static const struct phy_ops cdns_dphy_rx_ops = {
+	.power_on = cdns_dphy_rx_power_on,
+	.power_off = cdns_dphy_rx_power_off,
+	.configure = cdns_dphy_rx_configure,
+	.validate = cdns_dphy_rx_validate,
+};
+
+static int cdns_dphy_rx_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct phy_provider *provider;
+	struct cdns_dphy_rx *dphy;
+
+	dphy = devm_kzalloc(dev, sizeof(*dphy), GFP_KERNEL);
+	if (!dphy)
+		return -ENOMEM;
+
+	dev_set_drvdata(dev, dphy);
+	dphy->dev = dev;
+
+	dphy->regs = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(dphy->regs))
+		return PTR_ERR(dphy->regs);
+
+	dphy->phy = devm_phy_create(dev, NULL, &cdns_dphy_rx_ops);
+	if (IS_ERR(dphy->phy)) {
+		dev_err(dev, "Failed to create PHY: %ld\n", PTR_ERR(dphy->phy));
+		return PTR_ERR(dphy->phy);
+	}
+
+	phy_set_drvdata(dphy->phy, dphy);
+	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (IS_ERR(provider)) {
+		dev_err(dev, "Failed to register PHY provider: %ld\n",
+			PTR_ERR(provider));
+		return PTR_ERR(provider);
+	}
+
+	return 0;
+}
+
+static const struct of_device_id cdns_dphy_rx_of_match[] = {
+	{ .compatible = "cdns,dphy-rx" },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, cdns_dphy_rx_of_match);
+
+static struct platform_driver cdns_dphy_rx_platform_driver = {
+	.probe		= cdns_dphy_rx_probe,
+	.driver		= {
+		.name		= "cdns-mipi-dphy-rx",
+		.of_match_table	= cdns_dphy_rx_of_match,
+	},
+};
+module_platform_driver(cdns_dphy_rx_platform_driver);
+
+MODULE_AUTHOR("Pratyush Yadav <p.yadav@ti.com>");
+MODULE_DESCRIPTION("Cadence D-PHY Rx Driver");
+MODULE_LICENSE("GPL");

drivers/phy/cadence/phy-cadence-salvo.c

@@ -263,14 +263,9 @@ static int cdns_salvo_phy_probe(struct platform_device *pdev)
 	struct phy_provider *phy_provider;
 	struct device *dev = &pdev->dev;
 	struct cdns_salvo_phy *salvo_phy;
-	const struct of_device_id *match;
 	struct cdns_salvo_data *data;
 
-	match = of_match_device(cdns_salvo_phy_of_match, dev);
-	if (!match)
-		return -EINVAL;
-
-	data = (struct cdns_salvo_data *)match->data;
+	data = (struct cdns_salvo_data *)of_device_get_match_data(dev);
 	salvo_phy = devm_kzalloc(dev, sizeof(*salvo_phy), GFP_KERNEL);
 	if (!salvo_phy)
 		return -ENOMEM;

drivers/phy/cadence/phy-cadence-sierra.c

@@ -370,6 +370,7 @@ struct cdns_sierra_phy {
 	int nsubnodes;
 	u32 num_lanes;
 	bool autoconf;
+	int already_configured;
 	struct clk_onecell_data clk_data;
 	struct clk *output_clks[CDNS_SIERRA_OUTPUT_CLOCKS];
 };
@@ -517,7 +518,7 @@ static int cdns_sierra_phy_init(struct phy *gphy)
 	int i, j;
 
 	/* Initialise the PHY registers, unless auto configured */
-	if (phy->autoconf || phy->nsubnodes > 1)
+	if (phy->autoconf || phy->already_configured || phy->nsubnodes > 1)
 		return 0;
 
 	clk_set_rate(phy->input_clks[CMN_REFCLK_DIG_DIV], 25000000);
@@ -646,6 +647,18 @@ static const struct phy_ops ops = {
 	.owner		= THIS_MODULE,
 };
 
+static int cdns_sierra_noop_phy_on(struct phy *gphy)
+{
+	usleep_range(5000, 10000);
+
+	return 0;
+}
+
+static const struct phy_ops noop_ops = {
+	.power_on	= cdns_sierra_noop_phy_on,
+	.owner		= THIS_MODULE,
+};
+
 static u8 cdns_sierra_pll_mux_get_parent(struct clk_hw *hw)
 {
 	struct cdns_sierra_pll_mux *mux = to_cdns_sierra_pll_mux(hw);
@@ -1118,13 +1131,6 @@ static int cdns_sierra_phy_get_clocks(struct cdns_sierra_phy *sp,
 	struct clk *clk;
 	int ret;
 
-	clk = devm_clk_get_optional(dev, "phy_clk");
-	if (IS_ERR(clk)) {
-		dev_err(dev, "failed to get clock phy_clk\n");
-		return PTR_ERR(clk);
-	}
-	sp->input_clks[PHY_CLK] = clk;
-
 	clk = devm_clk_get_optional(dev, "cmn_refclk_dig_div");
 	if (IS_ERR(clk)) {
 		dev_err(dev, "cmn_refclk_dig_div clock not found\n");
@@ -1160,17 +1166,33 @@ static int cdns_sierra_phy_get_clocks(struct cdns_sierra_phy *sp,
 	return 0;
 }
 
-static int cdns_sierra_phy_enable_clocks(struct cdns_sierra_phy *sp)
+static int cdns_sierra_phy_clk(struct cdns_sierra_phy *sp)
 {
+	struct device *dev = sp->dev;
+	struct clk *clk;
 	int ret;
 
+	clk = devm_clk_get_optional(dev, "phy_clk");
+	if (IS_ERR(clk)) {
+		dev_err(dev, "failed to get clock phy_clk\n");
+		return PTR_ERR(clk);
+	}
+	sp->input_clks[PHY_CLK] = clk;
+
 	ret = clk_prepare_enable(sp->input_clks[PHY_CLK]);
 	if (ret)
 		return ret;
 
+	return 0;
+}
+
+static int cdns_sierra_phy_enable_clocks(struct cdns_sierra_phy *sp)
+{
+	int ret;
+
 	ret = clk_prepare_enable(sp->output_clks[CDNS_SIERRA_PLL_CMNLC]);
 	if (ret)
-		goto err_pll_cmnlc;
+		return ret;
 
 	ret = clk_prepare_enable(sp->output_clks[CDNS_SIERRA_PLL_CMNLC1]);
 	if (ret)
@@ -1181,9 +1203,6 @@ static int cdns_sierra_phy_enable_clocks(struct cdns_sierra_phy *sp)
 err_pll_cmnlc1:
 	clk_disable_unprepare(sp->output_clks[CDNS_SIERRA_PLL_CMNLC]);
 
-err_pll_cmnlc:
-	clk_disable_unprepare(sp->input_clks[PHY_CLK]);
-
 	return ret;
 }
 
@@ -1191,6 +1210,7 @@ static void cdns_sierra_phy_disable_clocks(struct cdns_sierra_phy *sp)
 {
 	clk_disable_unprepare(sp->output_clks[CDNS_SIERRA_PLL_CMNLC1]);
 	clk_disable_unprepare(sp->output_clks[CDNS_SIERRA_PLL_CMNLC]);
+	if (!sp->already_configured)
 		clk_disable_unprepare(sp->input_clks[PHY_CLK]);
 }
 
@@ -1382,22 +1402,30 @@ static int cdns_sierra_phy_probe(struct platform_device *pdev)
 	if (ret)
 		return ret;
 
-	ret = cdns_sierra_phy_get_resets(sp, dev);
+	ret = cdns_sierra_phy_enable_clocks(sp);
 	if (ret)
 		goto unregister_clk;
 
-	ret = cdns_sierra_phy_enable_clocks(sp);
+	regmap_field_read(sp->pma_cmn_ready, &sp->already_configured);
+
+	if (!sp->already_configured) {
+		ret = cdns_sierra_phy_clk(sp);
 		if (ret)
-		goto unregister_clk;
+			goto clk_disable;
+
+		ret = cdns_sierra_phy_get_resets(sp, dev);
+		if (ret)
+			goto clk_disable;
 
 		/* Enable APB */
 		reset_control_deassert(sp->apb_rst);
+	}
 
 	/* Check that PHY is present */
 	regmap_field_read(sp->macro_id_type, &id_value);
 	if  (sp->init_data->id_value != id_value) {
 		ret = -EINVAL;
-		goto clk_disable;
+		goto ctrl_assert;
 	}
 
 	sp->autoconf = of_property_read_bool(dn, "cdns,autoconf");
@@ -1433,8 +1461,10 @@ static int cdns_sierra_phy_probe(struct platform_device *pdev)
 
 		sp->num_lanes += sp->phys[node].num_lanes;
 
+		if (!sp->already_configured)
 			gphy = devm_phy_create(dev, child, &ops);
-
+		else
+			gphy = devm_phy_create(dev, child, &noop_ops);
 		if (IS_ERR(gphy)) {
 			ret = PTR_ERR(gphy);
 			of_node_put(child);
@@ -1455,7 +1485,7 @@ static int cdns_sierra_phy_probe(struct platform_device *pdev)
 	}
 
 	/* If more than one subnode, configure the PHY as multilink */
-	if (!sp->autoconf && sp->nsubnodes > 1) {
+	if (!sp->already_configured && !sp->autoconf && sp->nsubnodes > 1) {
 		ret = cdns_sierra_phy_configure_multilink(sp);
 		if (ret)
 			goto put_control;
@@ -1473,9 +1503,11 @@ static int cdns_sierra_phy_probe(struct platform_device *pdev)
 put_control:
 	while (--node >= 0)
 		reset_control_put(sp->phys[node].lnk_rst);
+ctrl_assert:
+	if (!sp->already_configured)
+		reset_control_assert(sp->apb_rst);
 clk_disable:
 	cdns_sierra_phy_disable_clocks(sp);
-	reset_control_assert(sp->apb_rst);
 unregister_clk:
 	cdns_sierra_clk_unregister(sp);
 	return ret;

drivers/phy/freescale/Kconfig

 # SPDX-License-Identifier: GPL-2.0-only
+
+if (ARCH_MXC && ARM64) || COMPILE_TEST
+
 config PHY_FSL_IMX8MQ_USB
 	tristate "Freescale i.MX8M USB3 PHY"
 	depends on OF && HAS_IOMEM
@@ -22,3 +25,5 @@ config PHY_FSL_IMX8M_PCIE
 	help
 	  Enable this to add support for the PCIE PHY as found on
 	  i.MX8M family of SOCs.
+
+endif

drivers/phy/freescale/phy-fsl-imx8m-pcie.c

@@ -5,9 +5,9 @@
 
 #include <linux/bitfield.h>
 #include <linux/clk.h>
+#include <linux/delay.h>
 #include <linux/io.h>
 #include <linux/iopoll.h>
-#include <linux/delay.h>
 #include <linux/mfd/syscon.h>
 #include <linux/mfd/syscon/imx7-iomuxc-gpr.h>
 #include <linux/module.h>
@@ -15,6 +15,7 @@
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
 #include <linux/reset.h>
+
 #include <dt-bindings/phy/phy-imx8-pcie.h>
 
 #define IMX8MM_PCIE_PHY_CMN_REG061	0x184

drivers/phy/phy-core-mipi-dphy.c

@@ -64,10 +64,10 @@ int phy_mipi_dphy_get_default_config(unsigned long pixel_clock,
 	cfg->hs_trail = max(4 * 8 * ui, 60000 + 4 * 4 * ui);
 
 	cfg->init = 100;
-	cfg->lpx = 60000;
+	cfg->lpx = 50000;
 	cfg->ta_get = 5 * cfg->lpx;
 	cfg->ta_go = 4 * cfg->lpx;
-	cfg->ta_sure = 2 * cfg->lpx;
+	cfg->ta_sure = cfg->lpx;
 	cfg->wakeup = 1000;
 
 	cfg->hs_clk_rate = hs_clk_rate;

drivers/phy/qualcomm/phy-qcom-edp.c

@@ -335,9 +335,11 @@ static int qcom_edp_phy_power_on(struct phy *phy)
 	writel(0x00, edp->tx0 + TXn_LANE_MODE_1);
 	writel(0x00, edp->tx1 + TXn_LANE_MODE_1);
 
+	if (edp->dp_opts.ssc) {
 		ret = qcom_edp_configure_ssc(edp);
 		if (ret)
 			return ret;
+	}
 
 	ret = qcom_edp_configure_pll(edp);
 	if (ret)
@@ -654,6 +656,7 @@ static int qcom_edp_phy_probe(struct platform_device *pdev)
 }
 
 static const struct of_device_id qcom_edp_phy_match_table[] = {
+	{ .compatible = "qcom,sc7280-edp-phy" },
 	{ .compatible = "qcom,sc8180x-edp-phy" },
 	{ }
 };

drivers/phy/qualcomm/phy-qcom-ipq806x-usb.c

@@ -10,6 +10,7 @@
 #include <linux/delay.h>
 #include <linux/regmap.h>
 #include <linux/mfd/syscon.h>
+#include <linux/bitfield.h>
 
 /* USB QSCRATCH Hardware registers */
 #define QSCRATCH_GENERAL_CFG		(0x08)
@@ -74,20 +75,20 @@
 		 PHY_PARAM_CTRL1_LOS_BIAS_MASK)
 
 #define PHY_PARAM_CTRL1_TX_FULL_SWING(x)	\
-		(((x) << 20) & PHY_PARAM_CTRL1_TX_FULL_SWING_MASK)
+		FIELD_PREP(PHY_PARAM_CTRL1_TX_FULL_SWING_MASK, (x))
 #define PHY_PARAM_CTRL1_TX_DEEMPH_6DB(x)	\
-		(((x) << 14) & PHY_PARAM_CTRL1_TX_DEEMPH_6DB_MASK)
+		FIELD_PREP(PHY_PARAM_CTRL1_TX_DEEMPH_6DB_MASK, (x))
 #define PHY_PARAM_CTRL1_TX_DEEMPH_3_5DB(x)	\
-		(((x) <<  8) & PHY_PARAM_CTRL1_TX_DEEMPH_3_5DB_MASK)
+		FIELD_PREP(PHY_PARAM_CTRL1_TX_DEEMPH_3_5DB_MASK, x)
 #define PHY_PARAM_CTRL1_LOS_BIAS(x)	\
-		(((x) <<  3) & PHY_PARAM_CTRL1_LOS_BIAS_MASK)
+		FIELD_PREP(PHY_PARAM_CTRL1_LOS_BIAS_MASK, (x))
 
 /* RX OVRD IN HI bits */
 #define RX_OVRD_IN_HI_RX_RESET_OVRD		BIT(13)
 #define RX_OVRD_IN_HI_RX_RX_RESET		BIT(12)
 #define RX_OVRD_IN_HI_RX_EQ_OVRD		BIT(11)
 #define RX_OVRD_IN_HI_RX_EQ_MASK		GENMASK(10, 7)
-#define RX_OVRD_IN_HI_RX_EQ(x)			((x) << 8)
+#define RX_OVRD_IN_HI_RX_EQ(x)			FIELD_PREP(RX_OVRD_IN_HI_RX_EQ_MASK, (x))
 #define RX_OVRD_IN_HI_RX_EQ_EN_OVRD		BIT(7)
 #define RX_OVRD_IN_HI_RX_EQ_EN			BIT(6)
 #define RX_OVRD_IN_HI_RX_LOS_FILTER_OVRD	BIT(5)
@@ -111,6 +112,9 @@
 #define SS_CR_READ_REG				BIT(0)
 #define SS_CR_WRITE_REG				BIT(0)
 
+#define LATCH_SLEEP				40
+#define LATCH_TIMEOUT				100
+
 struct usb_phy {
 	void __iomem		*base;
 	struct device		*dev;
@@ -156,19 +160,9 @@ static inline void usb_phy_write_readback(struct usb_phy *phy_dwc3,
 
 static int wait_for_latch(void __iomem *addr)
 {
-	u32 retry = 10;
-
-	while (true) {
-		if (!readl(addr))
-			break;
-
-		if (--retry == 0)
-			return -ETIMEDOUT;
-
-		usleep_range(10, 20);
-	}
+	u32 val;
 
-	return 0;
+	return readl_poll_timeout(addr, val, !val, LATCH_SLEEP, LATCH_TIMEOUT);
 }
 
 /**

drivers/phy/qualcomm/phy-qcom-qmp.c

@@ -5977,6 +5977,9 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
 	}, {
 		.compatible = "qcom,sc8180x-qmp-ufs-phy",
 		.data = &sm8150_ufsphy_cfg,
+	}, {
+		.compatible = "qcom,sc8280xp-qmp-ufs-phy",
+		.data = &sm8350_ufsphy_cfg,
 	}, {
 		.compatible = "qcom,sc8180x-qmp-usb3-phy",
 		.data = &sm8150_usb3phy_cfg,

drivers/phy/qualcomm/phy-qcom-qusb2.c

@@ -911,6 +911,9 @@ static const struct of_device_id qusb2_phy_of_match_table[] = {
 	}, {
 		.compatible	= "qcom,ipq8074-qusb2-phy",
 		.data		= &msm8996_phy_cfg,
+	}, {
+		.compatible	= "qcom,msm8953-qusb2-phy",
+		.data		= &msm8996_phy_cfg,
 	}, {
 		.compatible	= "qcom,msm8996-qusb2-phy",
 		.data		= &msm8996_phy_cfg,

drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c

@@ -32,6 +32,7 @@
 #define POR					BIT(1)
 
 #define USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0	(0x54)
+#define SIDDQ					BIT(2)
 #define RETENABLEN				BIT(3)
 #define FSEL_MASK				GENMASK(6, 4)
 #define FSEL_DEFAULT				(0x3 << 4)
@@ -233,6 +234,9 @@ static int qcom_snps_hsphy_init(struct phy *phy)
 	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_UTMI_CTRL0,
 					SLEEPM, SLEEPM);
 
+	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0,
+				   SIDDQ, 0);
+
 	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_UTMI_CTRL5,
 					POR, 0);
 
@@ -275,6 +279,7 @@ static const struct phy_ops qcom_snps_hsphy_gen_ops = {
 
 static const struct of_device_id qcom_snps_hsphy_of_match_table[] = {
 	{ .compatible	= "qcom,sm8150-usb-hs-phy", },
+	{ .compatible	= "qcom,usb-snps-hs-5nm-phy", },
 	{ .compatible	= "qcom,usb-snps-hs-7nm-phy", },
 	{ .compatible	= "qcom,usb-snps-femto-v2-phy",	},
 	{ }

drivers/phy/rockchip/Kconfig

@@ -66,6 +66,14 @@ config PHY_ROCKCHIP_INNO_DSIDPHY
 	  Enable this to support the Rockchip MIPI/LVDS/TTL PHY with
 	  Innosilicon IP block.
 
+config PHY_ROCKCHIP_NANENG_COMBO_PHY
+	tristate "Rockchip NANENG COMBO PHY Driver"
+	depends on ARCH_ROCKCHIP && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support the Rockchip PCIe/USB3.0/SATA/QSGMII
+	  combo PHY with NaNeng IP block.
+
 config PHY_ROCKCHIP_PCIE
 	tristate "Rockchip PCIe PHY Driver"
 	depends on (ARCH_ROCKCHIP && OF) || COMPILE_TEST

drivers/phy/rockchip/Makefile

@@ -6,6 +6,7 @@ obj-$(CONFIG_PHY_ROCKCHIP_INNO_CSIDPHY)	+= phy-rockchip-inno-csidphy.o
 obj-$(CONFIG_PHY_ROCKCHIP_INNO_DSIDPHY)	+= phy-rockchip-inno-dsidphy.o
 obj-$(CONFIG_PHY_ROCKCHIP_INNO_HDMI)	+= phy-rockchip-inno-hdmi.o
 obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2)	+= phy-rockchip-inno-usb2.o
+obj-$(CONFIG_PHY_ROCKCHIP_NANENG_COMBO_PHY)	+= phy-rockchip-naneng-combphy.o
 obj-$(CONFIG_PHY_ROCKCHIP_PCIE)		+= phy-rockchip-pcie.o
 obj-$(CONFIG_PHY_ROCKCHIP_TYPEC)	+= phy-rockchip-typec.o
 obj-$(CONFIG_PHY_ROCKCHIP_USB)		+= phy-rockchip-usb.o

drivers/usb/host/xhci-mvebu.c

@@ -8,7 +8,6 @@
 #include <linux/mbus.h>
 #include <linux/of.h>
 #include <linux/platform_device.h>
-#include <linux/phy/phy.h>
 
 #include <linux/usb.h>
 #include <linux/usb/hcd.h>
@@ -75,47 +74,6 @@ int xhci_mvebu_mbus_init_quirk(struct usb_hcd *hcd)
 	return 0;
 }
 
-int xhci_mvebu_a3700_plat_setup(struct usb_hcd *hcd)
-{
-	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
-	struct device *dev = hcd->self.controller;
-	struct phy *phy;
-	int ret;
-
-	/* Old bindings miss the PHY handle */
-	phy = of_phy_get(dev->of_node, "usb3-phy");
-	if (IS_ERR(phy) && PTR_ERR(phy) == -EPROBE_DEFER)
-		return -EPROBE_DEFER;
-	else if (IS_ERR(phy))
-		goto phy_out;
-
-	ret = phy_init(phy);
-	if (ret)
-		goto phy_put;
-
-	ret = phy_set_mode(phy, PHY_MODE_USB_HOST_SS);
-	if (ret)
-		goto phy_exit;
-
-	ret = phy_power_on(phy);
-	if (ret == -EOPNOTSUPP) {
-		/* Skip initializatin of XHCI PHY when it is unsupported by firmware */
-		dev_warn(dev, "PHY unsupported by firmware\n");
-		xhci->quirks |= XHCI_SKIP_PHY_INIT;
-	}
-	if (ret)
-		goto phy_exit;
-
-	phy_power_off(phy);
-phy_exit:
-	phy_exit(phy);
-phy_put:
-	of_phy_put(phy);
-phy_out:
-
-	return 0;
-}
-
 int xhci_mvebu_a3700_init_quirk(struct usb_hcd *hcd)
 {
 	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);

drivers/usb/host/xhci-mvebu.h

@@ -12,7 +12,6 @@ struct usb_hcd;
 
 #if IS_ENABLED(CONFIG_USB_XHCI_MVEBU)
 int xhci_mvebu_mbus_init_quirk(struct usb_hcd *hcd);
-int xhci_mvebu_a3700_plat_setup(struct usb_hcd *hcd);
 int xhci_mvebu_a3700_init_quirk(struct usb_hcd *hcd);
 #else
 static inline int xhci_mvebu_mbus_init_quirk(struct usb_hcd *hcd)
@@ -20,11 +19,6 @@ static inline int xhci_mvebu_mbus_init_quirk(struct usb_hcd *hcd)
 	return 0;
 }
 
-static inline int xhci_mvebu_a3700_plat_setup(struct usb_hcd *hcd)
-{
-	return 0;
-}
-
 static inline int xhci_mvebu_a3700_init_quirk(struct usb_hcd *hcd)
 {
 	return 0;

drivers/usb/host/xhci-plat.c

@@ -44,16 +44,6 @@ static void xhci_priv_plat_start(struct usb_hcd *hcd)
 		priv->plat_start(hcd);
 }
 
-static int xhci_priv_plat_setup(struct usb_hcd *hcd)
-{
-	struct xhci_plat_priv *priv = hcd_to_xhci_priv(hcd);
-
-	if (!priv->plat_setup)
-		return 0;
-
-	return priv->plat_setup(hcd);
-}
-
 static int xhci_priv_init_quirk(struct usb_hcd *hcd)
 {
 	struct xhci_plat_priv *priv = hcd_to_xhci_priv(hcd);
@@ -121,7 +111,6 @@ static const struct xhci_plat_priv xhci_plat_marvell_armada = {
 };
 
 static const struct xhci_plat_priv xhci_plat_marvell_armada3700 = {
-	.plat_setup = xhci_mvebu_a3700_plat_setup,
 	.init_quirk = xhci_mvebu_a3700_init_quirk,
 };
 
@@ -341,14 +330,7 @@ static int xhci_plat_probe(struct platform_device *pdev)
 
 	hcd->tpl_support = of_usb_host_tpl_support(sysdev->of_node);
 	xhci->shared_hcd->tpl_support = hcd->tpl_support;
-
-	if (priv) {
-		ret = xhci_priv_plat_setup(hcd);
-		if (ret)
-			goto disable_usb_phy;
-	}
-
-	if ((xhci->quirks & XHCI_SKIP_PHY_INIT) || (priv && (priv->quirks & XHCI_SKIP_PHY_INIT)))
+	if (priv && (priv->quirks & XHCI_SKIP_PHY_INIT))
 		hcd->skip_phy_initialization = 1;
 
 	if (priv && (priv->quirks & XHCI_SG_TRB_CACHE_SIZE_QUIRK))

drivers/usb/host/xhci-plat.h

@@ -13,7 +13,6 @@
 struct xhci_plat_priv {
 	const char *firmware_name;
 	unsigned long long quirks;
-	int (*plat_setup)(struct usb_hcd *);
 	void (*plat_start)(struct usb_hcd *);
 	int (*init_quirk)(struct usb_hcd *);
 	int (*suspend_quirk)(struct usb_hcd *);