macb: Move the Atmel driver

Move the Atmel driver into drivers/net/ethernet/cadence/ and
make the necessary Kconfig and Makefile changes.

CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>

MAINTAINERS

@@ -1323,7 +1323,7 @@ F:	include/video/atmel_lcdc.h
 ATMEL MACB ETHERNET DRIVER
 M:	Nicolas Ferre <nicolas.ferre@atmel.com>
 S:	Supported
-F:	drivers/net/macb.*
+F:	drivers/net/ethernet/cadence/
 
 ATMEL SPI DRIVER
 M:	Nicolas Ferre <nicolas.ferre@atmel.com>

drivers/net/Kconfig

@@ -2,9 +2,6 @@
 # Network device configuration
 #
 
-config HAVE_NET_MACB
-	bool
-
 menuconfig NETDEVICES
 	default y if UML
 	depends on NET
@@ -224,19 +221,6 @@ menuconfig NET_ETHERNET
 
 if NET_ETHERNET
 
-config MACB
-	tristate "Atmel MACB support"
-	depends on HAVE_NET_MACB
-	select PHYLIB
-	help
-	  The Atmel MACB ethernet interface is found on many AT32 and AT91
-	  parts. Say Y to include support for the MACB chip.
-
-	  To compile this driver as a module, choose M here: the module
-	  will be called macb.
-
-source "drivers/net/arm/Kconfig"
-
 config SH_ETH
 	tristate "Renesas SuperH Ethernet support"
 	depends on SUPERH && \

drivers/net/Makefile

@@ -63,9 +63,6 @@ obj-$(CONFIG_ETHOC) += ethoc.o
 obj-$(CONFIG_GRETH) += greth.o
 
 obj-$(CONFIG_DNET) += dnet.o
-obj-$(CONFIG_MACB) += macb.o
-
-obj-$(CONFIG_ARM) += arm/
 obj-$(CONFIG_DEV_APPLETALK) += appletalk/
 obj-$(CONFIG_ETHERNET) += ethernet/
 obj-$(CONFIG_TR) += tokenring/

drivers/net/arm/Kconfig

-#
-# Acorn Network device configuration
-#  These are for Acorn's Expansion card network interfaces
-#
-
-config ARM_AT91_ETHER
-	tristate "AT91RM9200 Ethernet support"
-	depends on ARM && ARCH_AT91RM9200
-	select MII
-	help
-	  If you wish to compile a kernel for the AT91RM9200 and enable
-	  ethernet support, then you should always answer Y to this.

drivers/net/arm/Makefile

-# File: drivers/net/arm/Makefile
-#
-# Makefile for the ARM network device drivers
-#
-
-obj-$(CONFIG_ARM_AT91_ETHER)	+= at91_ether.o

drivers/net/ethernet/Kconfig

@@ -15,6 +15,7 @@ source "drivers/net/ethernet/3com/Kconfig"
 source "drivers/net/ethernet/amd/Kconfig"
 source "drivers/net/ethernet/apple/Kconfig"
 source "drivers/net/ethernet/atheros/Kconfig"
+source "drivers/net/ethernet/cadence/Kconfig"
 source "drivers/net/ethernet/adi/Kconfig"
 source "drivers/net/ethernet/broadcom/Kconfig"
 source "drivers/net/ethernet/brocade/Kconfig"

drivers/net/ethernet/Makefile

@@ -7,6 +7,7 @@ obj-$(CONFIG_NET_VENDOR_8390) += 8390/
 obj-$(CONFIG_NET_VENDOR_AMD) += amd/
 obj-$(CONFIG_NET_VENDOR_APPLE) += apple/
 obj-$(CONFIG_NET_VENDOR_ATHEROS) += atheros/
+obj-$(CONFIG_NET_ATMEL) += cadence/
 obj-$(CONFIG_NET_BFIN) += adi/
 obj-$(CONFIG_NET_VENDOR_BROADCOM) += broadcom/
 obj-$(CONFIG_NET_VENDOR_BROCADE) += brocade/

drivers/net/ethernet/cadence/Kconfig

+#
+# Atmel device configuration
+#
+
+config HAVE_NET_MACB
+	bool
+
+config NET_ATMEL
+	bool "Atmel devices"
+	depends on HAVE_NET_MACB || (ARM && ARCH_AT91RM9200)
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y.
+	  Make sure you know the name of your card. Read the Ethernet-HOWTO,
+	  available from <http://www.tldp.org/docs.html#howto>.
+
+	  If unsure, say Y.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the remaining Atmel network card questions. If you say Y, you will be
+	  asked for your specific card in the following questions.
+
+if NET_ATMEL
+
+config ARM_AT91_ETHER
+	tristate "AT91RM9200 Ethernet support"
+	depends on ARM && ARCH_AT91RM9200
+	select MII
+	---help---
+	  If you wish to compile a kernel for the AT91RM9200 and enable
+	  ethernet support, then you should always answer Y to this.
+
+config MACB
+	tristate "Atmel MACB support"
+	depends on HAVE_NET_MACB
+	select PHYLIB
+	---help---
+	  The Atmel MACB ethernet interface is found on many AT32 and AT91
+	  parts. Say Y to include support for the MACB chip.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called macb.
+
+endif # NET_ATMEL

drivers/net/ethernet/cadence/Makefile

+#
+# Makefile for the Atmel network device drivers.
+#
+
+obj-$(CONFIG_ARM_AT91_ETHER) += at91_ether.o
+obj-$(CONFIG_MACB) += macb.o