Commit a0a6da1a authored by Linus Torvalds's avatar Linus Torvalds

Merge master.kernel.org:/home/rmk/linux-2.6-arm

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: GIC: don't disable software generated interrupts
  ARM: 6472/1: vexpress ct-ca9x4: only set twd_base if local timers are being used
  ARM: arch/arm/kernel/traps.c: Convert sprintf_symbol to %pS
  ARM: arch/arm/kernel/hw_breakpoint.c: Convert WARN_ON to WARN
  ARM: 6462/1: EP93xx: Document DMA M2P API
  ARM: 6470/1: atomic64: use generic implementation for OABI configurations
  ARM: 6469/1: perf-events: squash compiler warning
  ARM: 6468/1: backtrace: fix calculation of thread stack base
  ARM: Fix DMA coherent allocator alignment
  ARM: orion5x/kirkwood/mv78xx0: fix MPP configuration corner cases
  [ARM] TS-78xxx NAND resource type should be IORESOURCE_MEM
  ARM: pxa/saar: fix the building failure caused by typo
  ARM: pxa/cm-x2xx: remove duplicate call to pxa27x_init_irq
  ARM: pxa: fix the missing definition of IRQ_BOARD_END
  ARM: mmp: fix cpuid detection on mmp2
  [ARM] Kirkwood: restrict the scope of the PCIe reset workaround
  [ARM] Kirkwood: fix timer initialization for LaCie boards
  [ARM] Kirkwood: enhance TCLK detection
parents 7803c054 9395f6ea
......@@ -6,7 +6,7 @@ config ARM
select HAVE_MEMBLOCK
select RTC_LIB
select SYS_SUPPORTS_APM_EMULATION
select GENERIC_ATOMIC64 if (!CPU_32v6K)
select GENERIC_ATOMIC64 if (!CPU_32v6K || !AEABI)
select HAVE_OPROFILE if (HAVE_PERF_EVENTS)
select HAVE_ARCH_KGDB
select HAVE_KPROBES if (!XIP_KERNEL)
......
......@@ -251,15 +251,16 @@ void __init gic_dist_init(unsigned int gic_nr, void __iomem *base,
writel(cpumask, base + GIC_DIST_TARGET + i * 4 / 4);
/*
* Set priority on all interrupts.
* Set priority on all global interrupts.
*/
for (i = 0; i < max_irq; i += 4)
for (i = 32; i < max_irq; i += 4)
writel(0xa0a0a0a0, base + GIC_DIST_PRI + i * 4 / 4);
/*
* Disable all interrupts.
* Disable all interrupts. Leave the PPI and SGIs alone
* as these enables are banked registers.
*/
for (i = 0; i < max_irq; i += 32)
for (i = 32; i < max_irq; i += 32)
writel(0xffffffff, base + GIC_DIST_ENABLE_CLEAR + i * 4 / 32);
/*
......@@ -277,11 +278,30 @@ void __init gic_dist_init(unsigned int gic_nr, void __iomem *base,
void __cpuinit gic_cpu_init(unsigned int gic_nr, void __iomem *base)
{
void __iomem *dist_base;
int i;
if (gic_nr >= MAX_GIC_NR)
BUG();
dist_base = gic_data[gic_nr].dist_base;
BUG_ON(!dist_base);
gic_data[gic_nr].cpu_base = base;
/*
* Deal with the banked PPI and SGI interrupts - disable all
* PPI interrupts, ensure all SGI interrupts are enabled.
*/
writel(0xffff0000, dist_base + GIC_DIST_ENABLE_CLEAR);
writel(0x0000ffff, dist_base + GIC_DIST_ENABLE_SET);
/*
* Set priority on PPI and SGI interrupts
*/
for (i = 0; i < 32; i += 4)
writel(0xa0a0a0a0, dist_base + GIC_DIST_PRI + i * 4 / 4);
writel(0xf0, base + GIC_CPU_PRIMASK);
writel(1, base + GIC_CPU_CTRL);
}
......
......@@ -75,7 +75,7 @@ extern unsigned long it8152_base_address;
IT8152_PD_IRQ(1) USB (USBR)
IT8152_PD_IRQ(0) Audio controller (ACR)
*/
#define IT8152_IRQ(x) (IRQ_BOARD_END + (x))
#define IT8152_IRQ(x) (IRQ_BOARD_START + (x))
/* IRQ-sources in 3 groups - local devices, LPC (serial), and external PCI */
#define IT8152_LD_IRQ_COUNT 9
......
......@@ -748,8 +748,7 @@ static int hw_breakpoint_pending(unsigned long addr, unsigned int fsr,
breakpoint_handler(addr, regs);
break;
case ARM_ENTRY_ASYNC_WATCHPOINT:
WARN_ON("Asynchronous watchpoint exception taken. "
"Debugging results may be unreliable");
WARN(1, "Asynchronous watchpoint exception taken. Debugging results may be unreliable\n");
case ARM_ENTRY_SYNC_WATCHPOINT:
watchpoint_handler(addr, regs);
break;
......
......@@ -1749,7 +1749,7 @@ static inline int armv7_pmnc_has_overflowed(unsigned long pmnc)
static inline int armv7_pmnc_counter_has_overflowed(unsigned long pmnc,
enum armv7_counters counter)
{
int ret;
int ret = 0;
if (counter == ARMV7_CYCLE_COUNTER)
ret = pmnc & ARMV7_FLAG_C;
......
......@@ -28,7 +28,7 @@ int notrace unwind_frame(struct stackframe *frame)
/* only go to a higher address on the stack */
low = frame->sp;
high = ALIGN(low, THREAD_SIZE) + THREAD_SIZE;
high = ALIGN(low, THREAD_SIZE);
/* check current frame pointer is within bounds */
if (fp < (low + 12) || fp + 4 >= high)
......
......@@ -53,10 +53,7 @@ static void dump_mem(const char *, const char *, unsigned long, unsigned long);
void dump_backtrace_entry(unsigned long where, unsigned long from, unsigned long frame)
{
#ifdef CONFIG_KALLSYMS
char sym1[KSYM_SYMBOL_LEN], sym2[KSYM_SYMBOL_LEN];
sprint_symbol(sym1, where);
sprint_symbol(sym2, from);
printk("[<%08lx>] (%s) from [<%08lx>] (%s)\n", where, sym1, from, sym2);
printk("[<%08lx>] (%pS) from [<%08lx>] (%pS)\n", where, (void *)where, from, (void *)from);
#else
printk("Function entered at [<%08lx>] from [<%08lx>]\n", where, from);
#endif
......
......@@ -279,7 +279,7 @@ int unwind_frame(struct stackframe *frame)
/* only go to a higher address on the stack */
low = frame->sp;
high = ALIGN(low, THREAD_SIZE) + THREAD_SIZE;
high = ALIGN(low, THREAD_SIZE);
pr_debug("%s(pc = %08lx lr = %08lx sp = %08lx)\n", __func__,
frame->pc, frame->lr, frame->sp);
......
/*
* arch/arm/mach-ep93xx/include/mach/dma.h
/**
* DOC: EP93xx DMA M2P memory to peripheral and peripheral to memory engine
*
* The EP93xx DMA M2P subsystem handles DMA transfers between memory and
* peripherals. DMA M2P channels are available for audio, UARTs and IrDA.
* See chapter 10 of the EP93xx users guide for full details on the DMA M2P
* engine.
*
* See sound/soc/ep93xx/ep93xx-pcm.c for an example use of the DMA M2P code.
*
*/
#ifndef __ASM_ARCH_DMA_H
......@@ -8,12 +16,34 @@
#include <linux/list.h>
#include <linux/types.h>
/**
* struct ep93xx_dma_buffer - Information about a buffer to be transferred
* using the DMA M2P engine
*
* @list: Entry in DMA buffer list
* @bus_addr: Physical address of the buffer
* @size: Size of the buffer in bytes
*/
struct ep93xx_dma_buffer {
struct list_head list;
u32 bus_addr;
u16 size;
};
/**
* struct ep93xx_dma_m2p_client - Information about a DMA M2P client
*
* @name: Unique name for this client
* @flags: Client flags
* @cookie: User data to pass to callback functions
* @buffer_started: Non NULL function to call when a transfer is started.
* The arguments are the user data cookie and the DMA
* buffer which is starting.
* @buffer_finished: Non NULL function to call when a transfer is completed.
* The arguments are the user data cookie, the DMA buffer
* which has completed, and a boolean flag indicating if
* the transfer had an error.
*/
struct ep93xx_dma_m2p_client {
char *name;
u8 flags;
......@@ -24,10 +54,11 @@ struct ep93xx_dma_m2p_client {
struct ep93xx_dma_buffer *buf,
int bytes, int error);
/* Internal to the DMA code. */
/* private: Internal use only */
void *channel;
};
/* DMA M2P ports */
#define EP93XX_DMA_M2P_PORT_I2S1 0x00
#define EP93XX_DMA_M2P_PORT_I2S2 0x01
#define EP93XX_DMA_M2P_PORT_AAC1 0x02
......@@ -39,18 +70,80 @@ struct ep93xx_dma_m2p_client {
#define EP93XX_DMA_M2P_PORT_UART3 0x08
#define EP93XX_DMA_M2P_PORT_IRDA 0x09
#define EP93XX_DMA_M2P_PORT_MASK 0x0f
#define EP93XX_DMA_M2P_TX 0x00
#define EP93XX_DMA_M2P_RX 0x10
#define EP93XX_DMA_M2P_ABORT_ON_ERROR 0x20
#define EP93XX_DMA_M2P_IGNORE_ERROR 0x40
#define EP93XX_DMA_M2P_ERROR_MASK 0x60
/* DMA M2P client flags */
#define EP93XX_DMA_M2P_TX 0x00 /* Memory to peripheral */
#define EP93XX_DMA_M2P_RX 0x10 /* Peripheral to memory */
/*
* DMA M2P client error handling flags. See the EP93xx users guide
* documentation on the DMA M2P CONTROL register for more details
*/
#define EP93XX_DMA_M2P_ABORT_ON_ERROR 0x20 /* Abort on peripheral error */
#define EP93XX_DMA_M2P_IGNORE_ERROR 0x40 /* Ignore peripheral errors */
#define EP93XX_DMA_M2P_ERROR_MASK 0x60 /* Mask of error bits */
/**
* ep93xx_dma_m2p_client_register - Register a client with the DMA M2P
* subsystem
*
* @m2p: Client information to register
* returns 0 on success
*
* The DMA M2P subsystem allocates a channel and an interrupt line for the DMA
* client
*/
int ep93xx_dma_m2p_client_register(struct ep93xx_dma_m2p_client *m2p);
/**
* ep93xx_dma_m2p_client_unregister - Unregister a client from the DMA M2P
* subsystem
*
* @m2p: Client to unregister
*
* Any transfers currently in progress will be completed in hardware, but
* ignored in software.
*/
void ep93xx_dma_m2p_client_unregister(struct ep93xx_dma_m2p_client *m2p);
/**
* ep93xx_dma_m2p_submit - Submit a DMA M2P transfer
*
* @m2p: DMA Client to submit the transfer on
* @buf: DMA Buffer to submit
*
* If the current or next transfer positions are free on the M2P client then
* the transfer is started immediately. If not, the transfer is added to the
* list of pending transfers. This function must not be called from the
* buffer_finished callback for an M2P channel.
*
*/
void ep93xx_dma_m2p_submit(struct ep93xx_dma_m2p_client *m2p,
struct ep93xx_dma_buffer *buf);
/**
* ep93xx_dma_m2p_submit_recursive - Put a DMA transfer on the pending list
* for an M2P channel
*
* @m2p: DMA Client to submit the transfer on
* @buf: DMA Buffer to submit
*
* This function must only be called from the buffer_finished callback for an
* M2P channel. It is commonly used to add the next transfer in a chained list
* of DMA transfers.
*/
void ep93xx_dma_m2p_submit_recursive(struct ep93xx_dma_m2p_client *m2p,
struct ep93xx_dma_buffer *buf);
/**
* ep93xx_dma_m2p_flush - Flush all pending transfers on a DMA M2P client
*
* @m2p: DMA client to flush transfers on
*
* Any transfers currently in progress will be completed in hardware, but
* ignored in software.
*
*/
void ep93xx_dma_m2p_flush(struct ep93xx_dma_m2p_client *m2p);
#endif /* __ASM_ARCH_DMA_H */
......@@ -854,9 +854,8 @@ int __init kirkwood_find_tclk(void)
kirkwood_pcie_id(&dev, &rev);
if ((dev == MV88F6281_DEV_ID && (rev == MV88F6281_REV_A0 ||
rev == MV88F6281_REV_A1)) ||
(dev == MV88F6282_DEV_ID))
if (dev == MV88F6281_DEV_ID || dev == MV88F6282_DEV_ID)
if (((readl(SAMPLE_AT_RESET) >> 21) & 1) == 0)
return 200000000;
return 166666667;
......
......@@ -225,5 +225,5 @@ MACHINE_START(D2NET_V2, "LaCie d2 Network v2")
.init_machine = d2net_v2_init,
.map_io = kirkwood_map_io,
.init_irq = kirkwood_init_irq,
.timer = &lacie_v2_timer,
.timer = &kirkwood_timer,
MACHINE_END
......@@ -111,17 +111,3 @@ void __init lacie_v2_hdd_power_init(int hdd_num)
pr_err("Failed to power up HDD%d\n", i + 1);
}
}
/*****************************************************************************
* Timer
****************************************************************************/
static void lacie_v2_timer_init(void)
{
kirkwood_tclk = 166666667;
orion_time_init(IRQ_KIRKWOOD_BRIDGE, kirkwood_tclk);
}
struct sys_timer lacie_v2_timer = {
.init = lacie_v2_timer_init,
};
......@@ -13,6 +13,4 @@ void lacie_v2_register_flash(void);
void lacie_v2_register_i2c_devices(void);
void lacie_v2_hdd_power_init(int hdd_num);
extern struct sys_timer lacie_v2_timer;
#endif
......@@ -59,7 +59,7 @@ void __init kirkwood_mpp_conf(unsigned int *mpp_list)
}
printk("\n");
while (*mpp_list) {
for ( ; *mpp_list; mpp_list++) {
unsigned int num = MPP_NUM(*mpp_list);
unsigned int sel = MPP_SEL(*mpp_list);
int shift, gpio_mode;
......@@ -88,8 +88,6 @@ void __init kirkwood_mpp_conf(unsigned int *mpp_list)
if (sel != 0)
gpio_mode = 0;
orion_gpio_set_valid(num, gpio_mode);
mpp_list++;
}
printk(KERN_DEBUG " final MPP regs:");
......
......@@ -262,7 +262,7 @@ MACHINE_START(NETSPACE_V2, "LaCie Network Space v2")
.init_machine = netspace_v2_init,
.map_io = kirkwood_map_io,
.init_irq = kirkwood_init_irq,
.timer = &lacie_v2_timer,
.timer = &kirkwood_timer,
MACHINE_END
#endif
......@@ -272,7 +272,7 @@ MACHINE_START(INETSPACE_V2, "LaCie Internet Space v2")
.init_machine = netspace_v2_init,
.map_io = kirkwood_map_io,
.init_irq = kirkwood_init_irq,
.timer = &lacie_v2_timer,
.timer = &kirkwood_timer,
MACHINE_END
#endif
......@@ -282,6 +282,6 @@ MACHINE_START(NETSPACE_MAX_V2, "LaCie Network Space Max v2")
.init_machine = netspace_v2_init,
.map_io = kirkwood_map_io,
.init_irq = kirkwood_init_irq,
.timer = &lacie_v2_timer,
.timer = &kirkwood_timer,
MACHINE_END
#endif
......@@ -403,7 +403,7 @@ MACHINE_START(NET2BIG_V2, "LaCie 2Big Network v2")
.init_machine = netxbig_v2_init,
.map_io = kirkwood_map_io,
.init_irq = kirkwood_init_irq,
.timer = &lacie_v2_timer,
.timer = &kirkwood_timer,
MACHINE_END
#endif
......@@ -413,6 +413,6 @@ MACHINE_START(NET5BIG_V2, "LaCie 5Big Network v2")
.init_machine = netxbig_v2_init,
.map_io = kirkwood_map_io,
.init_irq = kirkwood_init_irq,
.timer = &lacie_v2_timer,
.timer = &kirkwood_timer,
MACHINE_END
#endif
......@@ -27,6 +27,10 @@
#include "mpp.h"
#include "tsx1x-common.h"
/* for the PCIe reset workaround */
#include <plat/pcie.h>
#define QNAP_TS41X_JUMPER_JP1 45
static struct i2c_board_info __initdata qnap_ts41x_i2c_rtc = {
......@@ -140,8 +144,16 @@ static void __init qnap_ts41x_init(void)
static int __init ts41x_pci_init(void)
{
if (machine_is_ts41x())
if (machine_is_ts41x()) {
/*
* Without this explicit reset, the PCIe SATA controller
* (Marvell 88sx7042/sata_mv) is known to stop working
* after a few minutes.
*/
orion_pcie_reset((void __iomem *)PCIE_VIRT_BASE);
kirkwood_pcie_init(KW_PCIE0);
}
return 0;
}
......
......@@ -46,7 +46,8 @@ static inline int cpu_is_pxa910(void)
#ifdef CONFIG_CPU_MMP2
static inline int cpu_is_mmp2(void)
{
return (((cpu_readid_id() >> 8) & 0xff) == 0x58);
return (((read_cpuid_id() >> 8) & 0xff) == 0x58);
}
#else
#define cpu_is_mmp2() (0)
#endif
......
......@@ -54,7 +54,7 @@ void __init mv78xx0_mpp_conf(unsigned int *mpp_list)
}
printk("\n");
while (*mpp_list) {
for ( ; *mpp_list; mpp_list++) {
unsigned int num = MPP_NUM(*mpp_list);
unsigned int sel = MPP_SEL(*mpp_list);
int shift, gpio_mode;
......@@ -83,8 +83,6 @@ void __init mv78xx0_mpp_conf(unsigned int *mpp_list)
if (sel != 0)
gpio_mode = 0;
orion_gpio_set_valid(num, gpio_mode);
mpp_list++;
}
printk(KERN_DEBUG " final MPP regs:");
......
......@@ -127,7 +127,7 @@ void __init orion5x_mpp_conf(struct orion5x_mpp_mode *mode)
/* Initialize gpiolib. */
orion_gpio_init();
while (mode->mpp >= 0) {
for ( ; mode->mpp >= 0; mode++) {
u32 *reg;
int num_type;
int shift;
......@@ -160,8 +160,6 @@ void __init orion5x_mpp_conf(struct orion5x_mpp_mode *mode)
orion_gpio_set_unused(mode->mpp);
orion_gpio_set_valid(mode->mpp, !!(mode->type == MPP_GPIO));
mode++;
}
writel(mpp_0_7_ctrl, MPP_0_7_CTRL);
......
......@@ -239,7 +239,7 @@ static struct platform_nand_data ts78xx_ts_nand_data = {
static struct resource ts78xx_ts_nand_resources = {
.start = TS_NAND_DATA,
.end = TS_NAND_DATA + 4,
.flags = IORESOURCE_IO,
.flags = IORESOURCE_MEM,
};
static struct platform_device ts78xx_ts_nand_device = {
......
......@@ -476,8 +476,6 @@ static void __init cmx2xx_init(void)
static void __init cmx2xx_init_irq(void)
{
pxa27x_init_irq();
if (cpu_is_pxa25x()) {
pxa25x_init_irq();
cmx2xx_pci_init_irq(CMX255_GPIO_IT8152_IRQ);
......
......@@ -116,7 +116,7 @@ static struct platform_device smc91x_device = {
},
};
#if defined(CONFIG_FB_PXA) || (CONFIG_FB_PXA_MODULE)
#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE)
static uint16_t lcd_power_on[] = {
/* single frame */
SMART_CMD_NOOP,
......
......@@ -54,7 +54,9 @@ static struct map_desc ct_ca9x4_io_desc[] __initdata = {
static void __init ct_ca9x4_map_io(void)
{
#ifdef CONFIG_LOCAL_TIMERS
twd_base = MMIO_P2V(A9_MPCORE_TWD);
#endif
v2m_map_io(ct_ca9x4_io_desc, ARRAY_SIZE(ct_ca9x4_io_desc));
}
......
......@@ -198,7 +198,7 @@ __dma_alloc_remap(struct page *page, size_t size, gfp_t gfp, pgprot_t prot)
* fragmentation of the DMA space, and also prevents allocations
* smaller than a section from crossing a section boundary.
*/
bit = fls(size - 1) + 1;
bit = fls(size - 1);
if (bit > SECTION_SHIFT)
bit = SECTION_SHIFT;
align = 1 << bit;
......
......@@ -11,12 +11,15 @@
#ifndef __PLAT_PCIE_H
#define __PLAT_PCIE_H
struct pci_bus;
u32 orion_pcie_dev_id(void __iomem *base);
u32 orion_pcie_rev(void __iomem *base);
int orion_pcie_link_up(void __iomem *base);
int orion_pcie_x4_mode(void __iomem *base);
int orion_pcie_get_local_bus_nr(void __iomem *base);
void orion_pcie_set_local_bus_nr(void __iomem *base, int nr);
void orion_pcie_reset(void __iomem *base);
void orion_pcie_setup(void __iomem *base,
struct mbus_dram_target_info *dram);
int orion_pcie_rd_conf(void __iomem *base, struct pci_bus *bus,
......
......@@ -181,11 +181,6 @@ void __init orion_pcie_setup(void __iomem *base,
u16 cmd;
u32 mask;
/*
* soft reset PCIe unit
*/
orion_pcie_reset(base);
/*
* Point PCIe unit MBUS decode windows to DRAM space.
*/
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment