Input: add driver for SiS 9200 family I2C touchscreen controllers

This is a driver for SiS 9200 family touchscreen controllers using I2C bus.
Signed-off-by: Mika Penttilä <mika.penttila@nextfour.com>
Acked-by: Tammy Tseng <tammy_tseng@sis.com>
Acked-by: Yuger Yu <yuger_yu@sis.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Documentation/devicetree/bindings/input/touchscreen/sis_i2c.txt

+* SiS I2C Multiple Touch Controller
+
+Required properties:
+- compatible: must be "sis,9200-ts"
+- reg: i2c slave address
+- interrupt-parent: the phandle for the interrupt controller
+  (see interrupt binding [0])
+- interrupts: touch controller interrupt (see interrupt
+  binding [0])
+
+Optional properties:
+- pinctrl-names: should be "default" (see pinctrl binding [1]).
+- pinctrl-0: a phandle pointing to the pin settings for the
+  device (see pinctrl binding [1]).
+- attn-gpios: the gpio pin used as attention line
+- reset-gpios: the gpio pin used to reset the controller
+- wakeup-source: touchscreen can be used as a wakeup source
+
+[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+[1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+Example:
+
+	sis9255@5c  {
+		compatible = "sis,9200-ts";
+		reg = <0x5c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sis>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <19 IRQ_TYPE_EDGE_FALLING>;
+		irq-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+		reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;
+	};

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -221,6 +221,7 @@ simtek
 sii	Seiko Instruments, Inc.
 silergy	Silergy Corp.
 sirf	SiRF Technology, Inc.
+sis	Silicon Integrated Systems Corp.
 sitronix	Sitronix Technology Corporation
 skyworks	Skyworks Solutions, Inc.
 smsc	Standard Microsystems Corporation

drivers/input/touchscreen/Kconfig

@@ -1071,6 +1071,18 @@ config TOUCHSCREEN_SILEAD
 	  To compile this driver as a module, choose M here: the
 	  module will be called silead.
 
+config TOUCHSCREEN_SIS_I2C
+	tristate "SiS 9200 family I2C touchscreen"
+	depends on I2C
+	depends on GPIOLIB || COMPILE_TEST
+	help
+	  This enables support for SiS 9200 family over I2C based touchscreens.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called sis_i2c.
+
 config TOUCHSCREEN_ST1232
 	tristate "Sitronix ST1232 touchscreen controllers"
 	depends on I2C

drivers/input/touchscreen/Makefile

@@ -65,6 +65,7 @@ obj-$(CONFIG_TOUCHSCREEN_PIXCIR)	+= pixcir_i2c_ts.o
 obj-$(CONFIG_TOUCHSCREEN_RM_TS)		+= raydium_i2c_ts.o
 obj-$(CONFIG_TOUCHSCREEN_S3C2410)	+= s3c2410_ts.o
 obj-$(CONFIG_TOUCHSCREEN_SILEAD)	+= silead.o
+obj-$(CONFIG_TOUCHSCREEN_SIS_I2C)	+= sis_i2c.o
 obj-$(CONFIG_TOUCHSCREEN_ST1232)	+= st1232.o
 obj-$(CONFIG_TOUCHSCREEN_STMPE)		+= stmpe-ts.o
 obj-$(CONFIG_TOUCHSCREEN_SUN4I)		+= sun4i-ts.o