wifi: wilc1000: fix incorrect power down sequence

Use the correct register configuration when the WILC chip is down so the
successive interface up operation is successful. The modified registers
values during chip down helps to avoid the "FW not responding" debug
message which sometimes occurs because of temporary bus communication
failure during the next start. Also, make sure on first communication with
the chip that it is indeed woken up.
Reported-by: Michael Walle <mwalle@kernel.org>
Closes: https://lore.kernel.org/linux-wireless/20221026085415.6jgwrhq4sunqaypm@0002.3ffe.de/Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115-wilc_1000_fixes-v1-4-54d29463a738@bootlin.com

drivers/net/wireless/microchip/wilc1000/wlan.c

@@ -1198,27 +1198,32 @@ int wilc_wlan_stop(struct wilc *wilc, struct wilc_vif *vif)
 
 	acquire_bus(wilc, WILC_BUS_ACQUIRE_AND_WAKEUP);
 
-	ret = wilc->hif_func->hif_read_reg(wilc, WILC_GP_REG_0, &reg);
-	if (ret) {
-		netdev_err(vif->ndev, "Error while reading reg\n");
+	ret = wilc->hif_func->hif_read_reg(wilc, GLOBAL_MODE_CONTROL, &reg);
+	if (ret)
 		goto release;
-	}
 
-	ret = wilc->hif_func->hif_write_reg(wilc, WILC_GP_REG_0,
-					(reg | WILC_ABORT_REQ_BIT));
-	if (ret) {
-		netdev_err(vif->ndev, "Error while writing reg\n");
+	reg &= ~WILC_GLOBAL_MODE_ENABLE_WIFI;
+	ret = wilc->hif_func->hif_write_reg(wilc, GLOBAL_MODE_CONTROL, reg);
+	if (ret)
+		goto release;
+
+	ret = wilc->hif_func->hif_read_reg(wilc, PWR_SEQ_MISC_CTRL, &reg);
+	if (ret)
+		goto release;
+
+	reg &= ~WILC_PWR_SEQ_ENABLE_WIFI_SLEEP;
+	ret = wilc->hif_func->hif_write_reg(wilc, PWR_SEQ_MISC_CTRL, reg);
+	if (ret)
 		goto release;
-	}
 
-	ret = wilc->hif_func->hif_read_reg(wilc, WILC_FW_HOST_COMM, &reg);
+	ret = wilc->hif_func->hif_read_reg(wilc, WILC_GP_REG_0, &reg);
 	if (ret) {
 		netdev_err(vif->ndev, "Error while reading reg\n");
 		goto release;
 	}
-	reg = BIT(0);
 
-	ret = wilc->hif_func->hif_write_reg(wilc, WILC_FW_HOST_COMM, reg);
+	ret = wilc->hif_func->hif_write_reg(wilc, WILC_GP_REG_0,
+					(reg | WILC_ABORT_REQ_BIT));
 	if (ret) {
 		netdev_err(vif->ndev, "Error while writing reg\n");
 		goto release;
@@ -1410,7 +1415,7 @@ static int init_chip(struct net_device *dev)
 	struct wilc_vif *vif = netdev_priv(dev);
 	struct wilc *wilc = vif->wilc;
 
-	acquire_bus(wilc, WILC_BUS_ACQUIRE_ONLY);
+	acquire_bus(wilc, WILC_BUS_ACQUIRE_AND_WAKEUP);
 
 	chipid = wilc_get_chipid(wilc, true);
 
@@ -1440,7 +1445,7 @@ static int init_chip(struct net_device *dev)
 	}
 
 release:
-	release_bus(wilc, WILC_BUS_RELEASE_ONLY);
+	release_bus(wilc, WILC_BUS_RELEASE_ALLOW_SLEEP);
 
 	return ret;
 }

drivers/net/wireless/microchip/wilc1000/wlan.h

@@ -156,6 +156,12 @@
 #define WILC_GP_REG_0			0x149c
 #define WILC_GP_REG_1			0x14a0
 
+#define GLOBAL_MODE_CONTROL		0x1614
+#define PWR_SEQ_MISC_CTRL		0x3008
+
+#define WILC_GLOBAL_MODE_ENABLE_WIFI	BIT(0)
+#define WILC_PWR_SEQ_ENABLE_WIFI_SLEEP	BIT(28)
+
 #define WILC_HAVE_SDIO_IRQ_GPIO		BIT(0)
 #define WILC_HAVE_USE_PMU		BIT(1)
 #define WILC_HAVE_SLEEP_CLK_SRC_RTC	BIT(2)