Merge tag 'pinctrl-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull bulk pin control changes from Linus Walleij:
 "This has been queued and tested for a while.  Lots of action here,
  like in the GPIO tree, embedded stuff like this is really hot now it
  seems.  Details in the signed tag.  I'm especially happy about the
  Qualcomm driver as it is used in such a huge subset of mobile handsets
  out there, and these platforms in general need better upstream support

   - New driver for the Qualcomm TLMM pin controller and its msm8x74
     subdriver.

   - New driver for the Broadcom Capri BCM281xx SoC.

   - New subdriver for the imx25 pin controller.

   - New subdriver for the Tegra124 pin controller.

   - Lock GPIO lines as IRQs for select combined pin control and GPIO
     drivers for baytrail and sirf.

   - Some semi-big refactorings and extenstions to the sirf driver.

   - Lots of patching, cleanup and fixing in the Renesas "PFC" driver
     and associated subdrivers as usual.  It is settling down a little
     bit now it seems.

   - Minor fixes and incremental updates here and there as usual"

* tag 'pinctrl-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
  pinctrl: sunxi: Honor GPIO output initial vaules
  pinctrl: capri: add dependency on OF
  ARM: bcm11351: Enable pinctrl for Broadcom Capri SoCs
  ARM: pinctrl: Add Broadcom Capri pinctrl driver
  pinctrl: Add pinctrl binding for Broadcom Capri SoCs
  pinctrl: Add void * to pinctrl_pin_desc
  pinctrl: st: Fix a typo in probe
  pinctrl: Fix some typos and grammar issues in the documentation
  pinctrl: sirf: lock IRQs when starting them
  pinctrl: sirf: put gpio interrupt pin into input status automatically
  pinctrl: sirf: use only one irq_domain for the whole device node
  pinctrl: single: fix infinite loop caused by bad mask
  pinctrl: single: fix pcs_disable with bits_per_mux
  pinctrl: single: fix DT bindings documentation
  pinctrl: as3722: Set pin to output mode for some function
  pinctrl: sirf: add pin group for USP0 with only RX or TX frame sync
  pinctrl: sirf: fix the pins of sdmmc5 connected with TriG
  pinctrl: sirf: add lost usp1_uart_nostreamctrl group for atlas6
  pinctrl: sunxi: Add Allwinner A20 clock output pin functions
  pinctrl/lantiq: fix typo
  ...

Documentation/devicetree/bindings/pinctrl/fsl,imx25-pinctrl.txt

+* Freescale IMX25 IOMUX Controller
+
+Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
+and usage.
+
+CONFIG bits definition:
+PAD_CTL_HYS			(1 << 8)
+PAD_CTL_PKE			(1 << 7)
+PAD_CTL_PUE			(1 << 6)
+PAD_CTL_PUS_100K_DOWN		(0 << 4)
+PAD_CTL_PUS_47K_UP		(1 << 4)
+PAD_CTL_PUS_100K_UP		(2 << 4)
+PAD_CTL_PUS_22K_UP		(3 << 4)
+PAD_CTL_ODE_CMOS		(0 << 3)
+PAD_CTL_ODE_OPENDRAIN		(1 << 3)
+PAD_CTL_DSE_NOMINAL		(0 << 1)
+PAD_CTL_DSE_HIGH		(1 << 1)
+PAD_CTL_DSE_MAX			(2 << 1)
+PAD_CTL_SRE_FAST		(1 << 0)
+PAD_CTL_SRE_SLOW		(0 << 0)
+
+Refer to imx25-pinfunc.h in device tree source folder for all available
+imx25 PIN_FUNC_ID.

Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt

@@ -52,12 +52,25 @@ Required properties for pin configuration node:
   CONFIG can be 0 or 1, meaning Pullup disable/enable.
 
 
+The iomux controller has gpio child nodes which are embedded in the iomux
+control registers. They have to be defined as child nodes of the iomux device
+node. If gpio subnodes are defined "#address-cells", "#size-cells" and "ranges"
+properties for the iomux device node are required.
 
 Example:
 
 iomuxc: iomuxc@10015000 {
 	compatible = "fsl,imx27-iomuxc";
 	reg = <0x10015000 0x600>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	gpio1: gpio@10015000 {
+		...
+	};
+
+	...
 
 	uart {
 		pinctrl_uart1: uart-1 {
@@ -83,6 +96,15 @@ The above example using macros:
 iomuxc: iomuxc@10015000 {
 	compatible = "fsl,imx27-iomuxc";
 	reg = <0x10015000 0x600>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	gpio1: gpio@10015000 {
+		...
+	};
+
+	...
 
 	uart {
 		pinctrl_uart1: uart-1 {

Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-pinmux.txt

+NVIDIA Tegra124 pinmux controller
+
+The Tegra124 pinctrl binding is very similar to the Tegra20 and Tegra30
+pinctrl binding, as described in nvidia,tegra20-pinmux.txt and
+nvidia,tegra30-pinmux.txt. In fact, this document assumes that binding as
+a baseline, and only documents the differences between the two bindings.
+
+Required properties:
+- compatible: "nvidia,tegra124-pinmux"
+- reg: Should contain a list of base address and size pairs for:
+    -- first entry - the drive strength and pad control registers.
+    -- second entry - the pinmux registers
+
+Tegra124 adds the following optional properties for pin configuration subnodes.
+The macros for options are defined in the
+	include/dt-binding/pinctrl/pinctrl-tegra.h.
+- nvidia,enable-input: Integer. Enable the pin's input path.
+		enable :TEGRA_PIN_ENABLE0 and
+		disable or output only: TEGRA_PIN_DISABLE.
+- nvidia,open-drain: Integer.
+		enable: TEGRA_PIN_ENABLE.
+		disable: TEGRA_PIN_DISABLE.
+- nvidia,lock: Integer. Lock the pin configuration against further changes
+    until reset.
+		enable: TEGRA_PIN_ENABLE.
+		disable: TEGRA_PIN_DISABLE.
+- nvidia,io-reset: Integer. Reset the IO path.
+		enable: TEGRA_PIN_ENABLE.
+		disable: TEGRA_PIN_DISABLE.
+- nvidia,rcv-sel: Integer. Select VIL/VIH receivers.
+		normal: TEGRA_PIN_DISABLE
+		high: TEGRA_PIN_ENABLE
+
+Please refer the Tegra TRM for complete details regarding which groups
+support which functionality.
+
+Valid values for pin and group names are:
+
+  per-pin mux groups:
+
+    These all support nvidia,function, nvidia,tristate, nvidia,pull,
+    nvidia,enable-input. Some support nvidia,lock nvidia,open-drain,
+    nvidia,io-reset and nvidia,rcv-sel.
+
+	ulpi_data0_po1, ulpi_data1_po2, ulpi_data2_po3, ulpi_data3_po4,
+	ulpi_data4_po5, ulpi_data5_po6, ulpi_data6_po7, ulpi_data7_po0,
+	ulpi_clk_py0, ulpi_dir_py1, ulpi_nxt_py2, ulpi_stp_py3, dap3_fs_pp0,
+	dap3_din_pp1, dap3_dout_pp2, dap3_sclk_pp3, pv0, pv1, sdmmc1_clk_pz0,
+	sdmmc1_cmd_pz1, sdmmc1_dat3_py4, sdmmc1_dat2_py5, sdmmc1_dat1_py6,
+	sdmmc1_dat0_py7, clk2_out_pw5, clk2_req_pcc5, hdmi_int_pn7, ddc_scl_pv4,
+	ddc_sda_pv5, uart2_rxd_pc3, uart2_txd_pc2, uart2_rts_n_pj6,
+	uart2_cts_n_pj5, uart3_txd_pw6, uart3_rxd_pw7, uart3_cts_n_pa1,
+	uart3_rts_n_pc0, pu0, pu1, pu2, pu3, pu4, pu5, pu6, gen1_i2c_scl_pc4,
+	gen1_i2c_sda_pc5, dap4_fs_pp4, dap4_din_pp5, dap4_dout_pp6,
+	dap4_sclk_pp7, clk3_out_pee0, clk3_req_pee1, pc7, pi5, pi7, pk0, pk1,
+	pj0, pj2, pk3, pk4, pk2, pi3, pi6, pg0, pg1, pg2, pg3, pg4, pg5, pg6,
+	pg7, ph0, ph1, ph2, ph3, ph4, ph5, ph6, ph7, pj7, pb0, pb1, pk7, pi0,
+	pi1, pi2, pi4, gen2_i2c_scl_pt5, gen2_i2c_sda_pt6, sdmmc4_clk_pcc4,
+	sdmmc4_cmd_pt7, sdmmc4_dat0_paa0, sdmmc4_dat1_paa1, sdmmc4_dat2_paa2,
+	sdmmc4_dat3_paa3, sdmmc4_dat4_paa4, sdmmc4_dat5_paa5, sdmmc4_dat6_paa6,
+	sdmmc4_dat7_paa7, cam_mclk_pcc0, pcc1, pbb0, cam_i2c_scl_pbb1,
+	cam_i2c_sda_pbb2, pbb3, pbb4, pbb5, pbb6, pbb7, pcc2, jtag_rtck,
+	pwr_i2c_scl_pz6, pwr_i2c_sda_pz7, kb_row0_pr0, kb_row1_pr1, kb_row2_pr2,
+	kb_row3_pr3, kb_row4_pr4, kb_row5_pr5, kb_row6_pr6, kb_row7_pr7,
+	kb_row8_ps0, kb_row9_ps1, kb_row10_ps2, kb_row11_ps3, kb_row12_ps4,
+	kb_row13_ps5, kb_row14_ps6, kb_row15_ps7, kb_col0_pq0, kb_col1_pq1,
+	kb_col2_pq2, kb_col3_pq3, kb_col4_pq4, kb_col5_pq5, kb_col6_pq6,
+	kb_col7_pq7, clk_32k_out_pa0, core_pwr_req, cpu_pwr_req, pwr_int_n,
+	clk_32k_in, owr, dap1_fs_pn0, dap1_din_pn1, dap1_dout_pn2,
+	dap1_sclk_pn3, dap_mclk1_req_pee2, dap_mclk1_pw4, spdif_in_pk6,
+	spdif_out_pk5, dap2_fs_pa2, dap2_din_pa4, dap2_dout_pa5, dap2_sclk_pa3,
+	dvfs_pwm_px0, gpio_x1_aud_px1, gpio_x3_aud_px3, dvfs_clk_px2,
+	gpio_x4_aud_px4, gpio_x5_aud_px5, gpio_x6_aud_px6, gpio_x7_aud_px7,
+	sdmmc3_clk_pa6, sdmmc3_cmd_pa7, sdmmc3_dat0_pb7, sdmmc3_dat1_pb6,
+	sdmmc3_dat2_pb5, sdmmc3_dat3_pb4, pex_l0_rst_n_pdd1,
+	pex_l0_clkreq_n_pdd2, pex_wake_n_pdd3, pex_l1_rst_n_pdd5,
+	pex_l1_clkreq_n_pdd6, hdmi_cec_pee3, sdmmc1_wp_n_pv3,
+	sdmmc3_cd_n_pv2, gpio_w2_aud_pw2, gpio_w3_aud_pw3, usb_vbus_en0_pn4,
+	usb_vbus_en1_pn5, sdmmc3_clk_lb_out_pee4, sdmmc3_clk_lb_in_pee5,
+	gmi_clk_lb, reset_out_n, kb_row16_pt0, kb_row17_pt1, usb_vbus_en2_pff1,
+	pff2, dp_hpd_pff0,
+
+  drive groups:
+
+    These all support nvidia,pull-down-strength, nvidia,pull-up-strength,
+    nvidia,slew-rate-rising, nvidia,slew-rate-falling. Most but not all
+    support nvidia,high-speed-mode, nvidia,schmitt, nvidia,low-power-mode
+    and nvidia,drive-type.
+
+    ao1, ao2, at1, at2, at3, at4, at5, cdev1, cdev2, dap1, dap2, dap3, dap4,
+    dbg, sdio3, spi, uaa, uab, uart2, uart3, sdio1, ddc, gma, gme, gmf, gmg,
+    gmh, owr, uda, gpv, dev3, cec, usb_vbus_en, ao3, ao0, hv0, sdio4, ao4.
+
+Valid values for nvidia,functions are:
+
+  blink, cec, cldvfs, clk12, cpu, dap, dap1, dap2, dev3, displaya,
+  displaya_alt, displayb, dtv, extperiph1, extperiph2, extperiph3,
+  gmi, gmi_alt, hda, hsi, i2c1, i2c2, i2c3, i2c4, i2cpwr, i2s0,
+  i2s1, i2s2, i2s3, i2s4, irda, kbc, owr, pmi, pwm0, pwm1, pwm2, pwm3,
+  pwron, reset_out_n, rsvd1, rsvd2, rsvd3, rsvd4, sdmmc1, sdmmc2, sdmmc3,
+  sdmmc4, soc, spdif, spi1, spi2, spi3, spi4, spi5, spi6, trace, uarta,
+  uartb, uartc, uartd, ulpi, usb, vgp1, vgp2, vgp3, vgp4, vgp5, vgp6,
+  vi, vi_alt1, vi_alt3, vimclk2, vimclk2_alt, sata, ccla, pe0, pe, pe1,
+  dp, rtck, sys, clk tmds.
+
+Example:
+
+	pinmux: pinmux {
+		compatible = "nvidia,tegra124-pinmux";
+		reg = <0x70000868 0x164		/* Pad control registers */
+		       0x70003000 0x434>;	/* PinMux registers */
+	};
+
+Example pinmux entries:
+
+	pinctrl {
+		sdmmc4_default: pinmux {
+			sdmmc4_clk_pcc4 {
+				nvidia,pins = "sdmmc4_clk_pcc4",
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_dat0_paa0 {
+				nvidia,pins = "sdmmc4_dat0_paa0",
+						"sdmmc4_dat1_paa1",
+						"sdmmc4_dat2_paa2",
+						"sdmmc4_dat3_paa3",
+						"sdmmc4_dat4_paa4",
+						"sdmmc4_dat5_paa5",
+						"sdmmc4_dat6_paa6",
+						"sdmmc4_dat7_paa7";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+		};
+	};
+
+	sdhci@78000400 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc4_default>;
+	};

Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt

@@ -151,6 +151,8 @@ drive-push-pull		- drive actively high and low
 drive-open-drain	- drive with open drain
 drive-open-source	- drive with open source
 drive-strength		- sink or source at most X mA
+input-enable		- enable input on pin (no effect on output)
+input-disable		- disable input on pin (no effect on output)
 input-schmitt-enable	- enable schmitt-trigger mode
 input-schmitt-disable	- disable schmitt-trigger mode
 input-debounce		- debounce mode with debound time X
@@ -158,6 +160,7 @@ low-power-enable	- enable low power mode
 low-power-disable	- disable low power mode
 output-low		- set the pin to output mode with low level
 output-high		- set the pin to output mode with high level
+slew-rate		- set the slew rate
 
 Some of the generic properties take arguments. For those that do, the
 arguments are described below.

Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt

@@ -98,7 +98,7 @@ below for more information.
 In case when one register changes more than one pin's mux the
 pinctrl-single,bits need to be used which takes three parameters:
 
-	pinctrl-single,bits = <0xdc 0x18, 0xff>;
+	pinctrl-single,bits = <0xdc 0x18 0xff>;
 
 Where 0xdc is the offset from the pinctrl register base address for the
 device pinctrl register, 0x18 is the desired value, and 0xff is the sub mask to

Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt

+Qualcomm MSM8974 TLMM block
+
+Required properties:
+- compatible: "qcom,msm8x74-pinctrl"
+- reg: Should be the base address and length of the TLMM block.
+- interrupts: Should be the parent IRQ of the TLMM block.
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells: Should be two.
+- gpio-controller: Marks the device node as a GPIO controller.
+- #gpio-cells : Should be two.
+                The first cell is the gpio pin number and the
+                second cell is used for optional parameters.
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Qualcomm's pin configuration nodes act as a container for an abitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+ pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength.
+
+Non-empty subnodes must specify the 'pins' property.
+Note that not all properties are valid for all pins.
+
+
+Valid values for qcom,pins are:
+  gpio0-gpio145
+    Supports mux, bias and drive-strength
+
+  sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data
+    Supports bias and drive-strength
+
+Valid values for qcom,function are:
+  blsp_i2c2, blsp_i2c6, blsp_i2c11, blsp_spi1, blsp_uart2, blsp_uart8, slimbus
+
+  (Note that this is not yet the complete list of functions)
+
+
+
+Example:
+
+	msmgpio: pinctrl@fd510000 {
+		compatible = "qcom,msm8974-pinctrl";
+		reg = <0xfd510000 0x4000>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupts = <0 208 0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart2_default>;
+
+		uart2_default: uart2_default {
+			mux {
+				qcom,pins = "gpio4", "gpio5";
+				qcom,function = "blsp_uart2";
+			};
+
+			tx {
+				qcom,pins = "gpio4";
+				drive-strength = <4>;
+				bias-disable;
+			};
+
+			rx {
+				qcom,pins = "gpio5";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+		};
+	};

Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt

@@ -26,6 +26,11 @@ Optional properties:
   - #gpio-range-cells: Mandatory when the PFC doesn't handle GPIO, forbidden
     otherwise. Should be 3.
 
+  - interrupts-extended: Specify the interrupts associated with external
+    IRQ pins. This property is mandatory when the PFC handles GPIOs and
+    forbidden otherwise. When specified, it must contain one interrupt per
+    external IRQ, sorted by external IRQ number.
+
 The PFC node also acts as a container for pin configuration nodes. Please refer
 to pinctrl-bindings.txt in this directory for the definition of the term "pin
 configuration node" and for the common pinctrl bindings used by client devices.
@@ -103,6 +108,15 @@ Example 1: SH73A0 (SH-Mobile AG5) pin controller node
 		      <0xe605801c 0x1c>;
 		gpio-controller;
 		#gpio-cells = <2>;
+		interrupts-extended =
+			<&irqpin0 0 0>, <&irqpin0 1 0>, <&irqpin0 2 0>, <&irqpin0 3 0>,
+			<&irqpin0 4 0>, <&irqpin0 5 0>, <&irqpin0 6 0>, <&irqpin0 7 0>,
+			<&irqpin1 0 0>, <&irqpin1 1 0>, <&irqpin1 2 0>, <&irqpin1 3 0>,
+			<&irqpin1 4 0>, <&irqpin1 5 0>, <&irqpin1 6 0>, <&irqpin1 7 0>,
+			<&irqpin2 0 0>, <&irqpin2 1 0>, <&irqpin2 2 0>, <&irqpin2 3 0>,
+			<&irqpin2 4 0>, <&irqpin2 5 0>, <&irqpin2 6 0>, <&irqpin2 7 0>,
+			<&irqpin3 0 0>, <&irqpin3 1 0>, <&irqpin3 2 0>, <&irqpin3 3 0>,
+			<&irqpin3 4 0>, <&irqpin3 5 0>, <&irqpin3 6 0>, <&irqpin3 7 0>;
 	};
 
 Example 2: A GPIO LED node that references a GPIO

Documentation/pinctrl.txt

@@ -18,7 +18,7 @@ Definition of PIN CONTROLLER:
 
 - A pin controller is a piece of hardware, usually a set of registers, that
   can control PINs. It may be able to multiplex, bias, set load capacitance,
-  set drive strength etc for individual pins or groups of pins.
+  set drive strength, etc. for individual pins or groups of pins.
 
 Definition of PIN:
 
@@ -90,7 +90,7 @@ selected drivers, you need to select them from your machine's Kconfig entry,
 since these are so tightly integrated with the machines they are used on.
 See for example arch/arm/mach-u300/Kconfig for an example.
 
-Pins usually have fancier names than this. You can find these in the dataheet
+Pins usually have fancier names than this. You can find these in the datasheet
 for your chip. Notice that the core pinctrl.h file provides a fancy macro
 called PINCTRL_PIN() to create the struct entries. As you can see I enumerated
 the pins from 0 in the upper left corner to 63 in the lower right corner.
@@ -185,7 +185,7 @@ static struct pinctrl_desc foo_desc = {
 };
 
 The pin control subsystem will call the .get_groups_count() function to
-determine total number of legal selectors, then it will call the other functions
+determine the total number of legal selectors, then it will call the other functions
 to retrieve the name and pins of the group. Maintaining the data structure of
 the groups is up to the driver, this is just a simple example - in practice you
 may need more entries in your group structure, for example specific register
@@ -195,7 +195,7 @@ ranges associated with each group and so on.
 Pin configuration
 =================
 
-Pins can sometimes be software-configured in an various ways, mostly related
+Pins can sometimes be software-configured in various ways, mostly related
 to their electronic properties when used as inputs or outputs. For example you
 may be able to make an output pin high impedance, or "tristate" meaning it is
 effectively disconnected. You may be able to connect an input pin to VDD or GND
@@ -291,7 +291,7 @@ Since the pin controller subsystem have its pinspace local to the pin
 controller we need a mapping so that the pin control subsystem can figure out
 which pin controller handles control of a certain GPIO pin. Since a single
 pin controller may be muxing several GPIO ranges (typically SoCs that have
-one set of pins but internally several GPIO silicon blocks, each modelled as
+one set of pins, but internally several GPIO silicon blocks, each modelled as
 a struct gpio_chip) any number of GPIO ranges can be added to a pin controller
 instance like this:
 
@@ -373,9 +373,9 @@ will be called on that specific pin controller.
 
 For all functionalities dealing with pin biasing, pin muxing etc, the pin
 controller subsystem will look up the corresponding pin number from the passed
-in gpio number, and use the range's internals to retrive a pin number. After
+in gpio number, and use the range's internals to retrieve a pin number. After
 that, the subsystem passes it on to the pin control driver, so the driver
-will get an pin number into its handled number range. Further it is also passed
+will get a pin number into its handled number range. Further it is also passed
 the range ID value, so that the pin controller knows which range it should
 deal with.
 
@@ -430,8 +430,8 @@ pins you see some will be taken by things like a few VCC and GND to feed power
 to the chip, and quite a few will be taken by large ports like an external
 memory interface. The remaining pins will often be subject to pin multiplexing.
 
-The example 8x8 PGA package above will have pin numbers 0 thru 63 assigned to
-its physical pins. It will name the pins { A1, A2, A3 ... H6, H7, H8 } using
+The example 8x8 PGA package above will have pin numbers 0 through 63 assigned
+to its physical pins. It will name the pins { A1, A2, A3 ... H6, H7, H8 } using
 pinctrl_register_pins() and a suitable data set as shown earlier.
 
 In this 8x8 BGA package the pins { A8, A7, A6, A5 } can be used as an SPI port
@@ -442,7 +442,7 @@ we cannot use the SPI port and I2C port at the same time. However in the inside
 of the package the silicon performing the SPI logic can alternatively be routed
 out on pins { G4, G3, G2, G1 }.
 
-On the botton row at { A1, B1, C1, D1, E1, F1, G1, H1 } we have something
+On the bottom row at { A1, B1, C1, D1, E1, F1, G1, H1 } we have something
 special - it's an external MMC bus that can be 2, 4 or 8 bits wide, and it will
 consume 2, 4 or 8 pins respectively, so either { A1, B1 } are taken or
 { A1, B1, C1, D1 } or all of them. If we use all 8 bits, we cannot use the SPI
@@ -549,7 +549,7 @@ Assumptions:
 
 We assume that the number of possible function maps to pin groups is limited by
 the hardware. I.e. we assume that there is no system where any function can be
-mapped to any pin, like in a phone exchange. So the available pins groups for
+mapped to any pin, like in a phone exchange. So the available pin groups for
 a certain function will be limited to a few choices (say up to eight or so),
 not hundreds or any amount of choices. This is the characteristic we have found
 by inspecting available pinmux hardware, and a necessary assumption since we
@@ -564,7 +564,7 @@ The pinmux core takes care of preventing conflicts on pins and calling
 the pin controller driver to execute different settings.
 
 It is the responsibility of the pinmux driver to impose further restrictions
-(say for example infer electronic limitations due to load etc) to determine
+(say for example infer electronic limitations due to load, etc.) to determine
 whether or not the requested function can actually be allowed, and in case it
 is possible to perform the requested mux setting, poke the hardware so that
 this happens.
@@ -755,7 +755,7 @@ Pin control interaction with the GPIO subsystem
 Note that the following implies that the use case is to use a certain pin
 from the Linux kernel using the API in <linux/gpio.h> with gpio_request()
 and similar functions. There are cases where you may be using something
-that your datasheet calls "GPIO mode" but actually is just an electrical
+that your datasheet calls "GPIO mode", but actually is just an electrical
 configuration for a certain device. See the section below named
 "GPIO mode pitfalls" for more details on this scenario.
 
@@ -871,7 +871,7 @@ hardware and shall be put into different subsystems:
 
 - Registers (or fields within registers) that control muxing of signals
   from various other HW blocks (e.g. I2C, MMC, or GPIO) onto pins should
-  be exposed through the pinctrl subssytem, as mux functions.
+  be exposed through the pinctrl subsystem, as mux functions.
 
 - Registers (or fields within registers) that control GPIO functionality
   such as setting a GPIO's output value, reading a GPIO's input value, or
@@ -895,7 +895,7 @@ Example: a pin is usually muxed in to be used as a UART TX line. But during
 system sleep, we need to put this pin into "GPIO mode" and ground it.
 
 If you make a 1-to-1 map to the GPIO subsystem for this pin, you may start
-to think that you need to come up with something real complex, that the
+to think that you need to come up with something really complex, that the
 pin shall be used for UART TX and GPIO at the same time, that you will grab
 a pin control handle and set it to a certain state to enable UART TX to be
 muxed in, then twist it over to GPIO mode and use gpio_direction_output()
@@ -964,12 +964,12 @@ GPIO mode.
 This will give the desired effect without any bogus interaction with the
 GPIO subsystem. It is just an electrical configuration used by that device
 when going to sleep, it might imply that the pin is set into something the
-datasheet calls "GPIO mode" but that is not the point: it is still used
+datasheet calls "GPIO mode", but that is not the point: it is still used
 by that UART device to control the pins that pertain to that very UART
 driver, putting them into modes needed by the UART. GPIO in the Linux
 kernel sense are just some 1-bit line, and is a different use case.
 
-How the registers are poked to attain the push/pull and output low
+How the registers are poked to attain the push or pull, and output low
 configuration and the muxing of the "u0" or "gpio-mode" group onto these
 pins is a question for the driver.
 
@@ -977,7 +977,7 @@ Some datasheets will be more helpful and refer to the "GPIO mode" as
 "low power mode" rather than anything to do with GPIO. This often means
 the same thing electrically speaking, but in this latter case the
 software engineers will usually quickly identify that this is some
-specific muxing/configuration rather than anything related to the GPIO
+specific muxing or configuration rather than anything related to the GPIO
 API.
 
 
@@ -1024,8 +1024,7 @@ up the device struct (just like with clockdev or regulators). The function name
 must match a function provided by the pinmux driver handling this pin range.
 
 As you can see we may have several pin controllers on the system and thus
-we need to specify which one of them that contain the functions we wish
-to map.
+we need to specify which one of them contains the functions we wish to map.
 
 You register this pinmux mapping to the pinmux subsystem by simply:
 
@@ -1254,10 +1253,10 @@ The semantics of the pinctrl APIs are:
   pinctrl_get().
 
 - pinctrl_lookup_state() is called in process context to obtain a handle to a
-  specific state for a the client device. This operation may be slow too.
+  specific state for a client device. This operation may be slow, too.
 
 - pinctrl_select_state() programs pin controller hardware according to the
-  definition of the state as given by the mapping table. In theory this is a
+  definition of the state as given by the mapping table. In theory, this is a
   fast-path operation, since it only involved blasting some register settings
   into hardware. However, note that some pin controllers may have their
   registers on a slow/IRQ-based bus, so client devices should not assume they

arch/arm/boot/dts/bcm11351.dtsi

@@ -142,4 +142,8 @@ sdio4: sdio@3f1b0000 {
 		status = "disabled";
 	};
 
+	pinctrl@35004800 {
+		compatible = "brcm,capri-pinctrl";
+		reg = <0x35004800 0x430>;
+	};
 };

arch/arm/configs/bcm_defconfig

@@ -126,3 +126,4 @@ CONFIG_CRC_ITU_T=y
 CONFIG_CRC7=y
 CONFIG_XZ_DEC=y
 CONFIG_AVERAGE=y
+CONFIG_PINCTRL_CAPRI=y

arch/arm/mach-bcm/Kconfig

@@ -25,6 +25,7 @@ config ARCH_BCM_MOBILE
 	select TICK_ONESHOT
 	select CACHE_L2X0
 	select HAVE_ARM_ARCH_TIMER
+	select PINCTRL
 	help
 	  This enables support for systems based on Broadcom mobile SoCs.
 	  It currently supports the 'BCM281XX' family, which includes

drivers/pinctrl/Kconfig

@@ -104,6 +104,19 @@ config PINCTRL_BCM2835
 	select PINMUX
 	select PINCONF
 
+config PINCTRL_CAPRI
+	bool "Broadcom Capri pinctrl driver"
+	depends on OF
+	select PINMUX
+	select PINCONF
+	select GENERIC_PINCONF
+	select REGMAP_MMIO
+	help
+	  Say Y here to support Broadcom Capri pinctrl driver, which is used for
+	  the BCM281xx SoC family, including BCM11130, BCM11140, BCM11351,
+	  BCM28145, and BCM28155 SoCs.  This driver requires the pinctrl
+	  framework.  GPIO is provided by a separate GPIO driver.
+
 config PINCTRL_IMX
 	bool
 	select PINMUX
@@ -116,15 +129,22 @@ config PINCTRL_IMX1_CORE
 
 config PINCTRL_IMX27
 	bool "IMX27 pinctrl driver"
-	depends on OF
 	depends on SOC_IMX27
 	select PINCTRL_IMX1_CORE
 	help
 	  Say Y here to enable the imx27 pinctrl driver
 
+
+config PINCTRL_IMX25
+        bool "IMX25 pinctrl driver"
+        depends on OF
+        depends on SOC_IMX25
+        select PINCTRL_IMX
+        help
+          Say Y here to enable the imx25 pinctrl driver
+
 config PINCTRL_IMX35
 	bool "IMX35 pinctrl driver"
-	depends on OF
 	depends on SOC_IMX35
 	select PINCTRL_IMX
 	help
@@ -132,7 +152,6 @@ config PINCTRL_IMX35
 
 config PINCTRL_IMX50
 	bool "IMX50 pinctrl driver"
-	depends on OF
 	depends on SOC_IMX50
 	select PINCTRL_IMX
 	help
@@ -140,7 +159,6 @@ config PINCTRL_IMX50
 
 config PINCTRL_IMX51
 	bool "IMX51 pinctrl driver"
-	depends on OF
 	depends on SOC_IMX51
 	select PINCTRL_IMX
 	help
@@ -148,7 +166,6 @@ config PINCTRL_IMX51
 
 config PINCTRL_IMX53
 	bool "IMX53 pinctrl driver"
-	depends on OF
 	depends on SOC_IMX53
 	select PINCTRL_IMX
 	help
@@ -156,7 +173,6 @@ config PINCTRL_IMX53
 
 config PINCTRL_IMX6Q
 	bool "IMX6Q/DL pinctrl driver"
-	depends on OF
 	depends on SOC_IMX6Q
 	select PINCTRL_IMX
 	help
@@ -164,7 +180,6 @@ config PINCTRL_IMX6Q
 
 config PINCTRL_IMX6SL
 	bool "IMX6SL pinctrl driver"
-	depends on OF
 	depends on SOC_IMX6SL
 	select PINCTRL_IMX
 	help
@@ -172,7 +187,6 @@ config PINCTRL_IMX6SL
 
 config PINCTRL_VF610
 	bool "Freescale Vybrid VF610 pinctrl driver"
-	depends on OF
 	depends on SOC_VF610
 	select PINCTRL_IMX
 	help
@@ -202,6 +216,20 @@ config PINCTRL_IMX28
 	bool
 	select PINCTRL_MXS
 
+config PINCTRL_MSM
+	tristate
+	select PINMUX
+	select PINCONF
+	select GENERIC_PINCONF
+
+config PINCTRL_MSM8X74
+	tristate "Qualcomm 8x74 pin controller driver"
+	depends on GPIOLIB && OF && OF_IRQ
+	select PINCTRL_MSM
+	help
+	  This is the pinctrl, pinmux, pinconf and gpiolib driver for the
+	  Qualcomm TLMM block found in the Qualcomm 8974 platform.
+
 config PINCTRL_NOMADIK
 	bool "Nomadik pin controller driver"
 	depends on ARCH_U8500 || ARCH_NOMADIK
@@ -268,6 +296,10 @@ config PINCTRL_TEGRA114
 	bool
 	select PINCTRL_TEGRA
 
+config PINCTRL_TEGRA124
+	bool
+	select PINCTRL_TEGRA
+
 config PINCTRL_TZ1090
 	bool "Toumaz Xenif TZ1090 pin control driver"
 	depends on SOC_TZ1090

drivers/pinctrl/Makefile

@@ -21,6 +21,7 @@ obj-$(CONFIG_PINCTRL_BF60x)	+= pinctrl-adi2-bf60x.o
 obj-$(CONFIG_PINCTRL_AT91)	+= pinctrl-at91.o
 obj-$(CONFIG_PINCTRL_BCM2835)	+= pinctrl-bcm2835.o
 obj-$(CONFIG_PINCTRL_BAYTRAIL)	+= pinctrl-baytrail.o
+obj-$(CONFIG_PINCTRL_CAPRI)	+= pinctrl-capri.o
 obj-$(CONFIG_PINCTRL_IMX)	+= pinctrl-imx.o
 obj-$(CONFIG_PINCTRL_IMX1_CORE)	+= pinctrl-imx1-core.o
 obj-$(CONFIG_PINCTRL_IMX27)	+= pinctrl-imx27.o
@@ -34,7 +35,10 @@ obj-$(CONFIG_PINCTRL_IMX6SL)	+= pinctrl-imx6sl.o
 obj-$(CONFIG_PINCTRL_FALCON)	+= pinctrl-falcon.o
 obj-$(CONFIG_PINCTRL_MXS)	+= pinctrl-mxs.o
 obj-$(CONFIG_PINCTRL_IMX23)	+= pinctrl-imx23.o
+obj-$(CONFIG_PINCTRL_IMX25)	+= pinctrl-imx25.o
 obj-$(CONFIG_PINCTRL_IMX28)	+= pinctrl-imx28.o
+obj-$(CONFIG_PINCTRL_MSM)	+= pinctrl-msm.o
+obj-$(CONFIG_PINCTRL_MSM8X74)	+= pinctrl-msm8x74.o
 obj-$(CONFIG_PINCTRL_NOMADIK)	+= pinctrl-nomadik.o
 obj-$(CONFIG_PINCTRL_STN8815)	+= pinctrl-nomadik-stn8815.o
 obj-$(CONFIG_PINCTRL_DB8500)	+= pinctrl-nomadik-db8500.o
@@ -48,6 +52,7 @@ obj-$(CONFIG_PINCTRL_TEGRA)	+= pinctrl-tegra.o
 obj-$(CONFIG_PINCTRL_TEGRA20)	+= pinctrl-tegra20.o
 obj-$(CONFIG_PINCTRL_TEGRA30)	+= pinctrl-tegra30.o
 obj-$(CONFIG_PINCTRL_TEGRA114)	+= pinctrl-tegra114.o
+obj-$(CONFIG_PINCTRL_TEGRA124)	+= pinctrl-tegra124.o
 obj-$(CONFIG_PINCTRL_TZ1090)	+= pinctrl-tz1090.o
 obj-$(CONFIG_PINCTRL_TZ1090_PDC)	+= pinctrl-tz1090-pdc.o
 obj-$(CONFIG_PINCTRL_U300)	+= pinctrl-u300.o

drivers/pinctrl/pinconf-generic.c

@@ -48,6 +48,7 @@ static struct pin_config_item conf_items[] = {
 	PCONFDUMP(PIN_CONFIG_DRIVE_OPEN_DRAIN, "output drive open drain", NULL),
 	PCONFDUMP(PIN_CONFIG_DRIVE_OPEN_SOURCE, "output drive open source", NULL),
 	PCONFDUMP(PIN_CONFIG_DRIVE_STRENGTH, "output drive strength", "mA"),
+	PCONFDUMP(PIN_CONFIG_INPUT_ENABLE, "input enabled", NULL),
 	PCONFDUMP(PIN_CONFIG_INPUT_SCHMITT_ENABLE, "input schmitt enabled", NULL),
 	PCONFDUMP(PIN_CONFIG_INPUT_SCHMITT, "input schmitt trigger", NULL),
 	PCONFDUMP(PIN_CONFIG_INPUT_DEBOUNCE, "input debounce", "usec"),
@@ -160,6 +161,8 @@ static struct pinconf_generic_dt_params dt_params[] = {
 	{ "drive-open-drain", PIN_CONFIG_DRIVE_OPEN_DRAIN, 0 },
 	{ "drive-open-source", PIN_CONFIG_DRIVE_OPEN_SOURCE, 0 },
 	{ "drive-strength", PIN_CONFIG_DRIVE_STRENGTH, 0 },
+	{ "input-enable", PIN_CONFIG_INPUT_ENABLE, 1 },
+	{ "input-disable", PIN_CONFIG_INPUT_ENABLE, 0 },
 	{ "input-schmitt-enable", PIN_CONFIG_INPUT_SCHMITT_ENABLE, 1 },
 	{ "input-schmitt-disable", PIN_CONFIG_INPUT_SCHMITT_ENABLE, 0 },
 	{ "input-debounce", PIN_CONFIG_INPUT_DEBOUNCE, 0 },
@@ -167,6 +170,7 @@ static struct pinconf_generic_dt_params dt_params[] = {
 	{ "low-power-disable", PIN_CONFIG_LOW_POWER_MODE, 0 },
 	{ "output-low", PIN_CONFIG_OUTPUT, 0, },
 	{ "output-high", PIN_CONFIG_OUTPUT, 1, },
+	{ "slew-rate", PIN_CONFIG_SLEW_RATE, 0},
 };
 
 /**

drivers/pinctrl/pinconf.c

@@ -28,12 +28,6 @@ int pinconf_check_ops(struct pinctrl_dev *pctldev)
 {
 	const struct pinconf_ops *ops = pctldev->desc->confops;
 
-	/* We must be able to read out pin status */
-	if (!ops->pin_config_get && !ops->pin_config_group_get) {
-		dev_err(pctldev->dev,
-			"pinconf must be able to read out pin status\n");
-		return -EINVAL;
-	}
 	/* We have to be able to config the pins in SOME way */
 	if (!ops->pin_config_set && !ops->pin_config_group_set) {
 		dev_err(pctldev->dev,
@@ -67,9 +61,9 @@ int pin_config_get_for_pin(struct pinctrl_dev *pctldev, unsigned pin,
 	const struct pinconf_ops *ops = pctldev->desc->confops;
 
 	if (!ops || !ops->pin_config_get) {
-		dev_err(pctldev->dev, "cannot get pin configuration, missing "
+		dev_dbg(pctldev->dev, "cannot get pin configuration, missing "
 			"pin_config_get() function in driver\n");
-		return -EINVAL;
+		return -ENOTSUPP;
 	}
 
 	return ops->pin_config_get(pctldev, pin, config);
@@ -93,10 +87,10 @@ int pin_config_group_get(const char *dev_name, const char *pin_group,
 	ops = pctldev->desc->confops;
 
 	if (!ops || !ops->pin_config_group_get) {
-		dev_err(pctldev->dev, "cannot get configuration for pin "
+		dev_dbg(pctldev->dev, "cannot get configuration for pin "
 			"group, missing group config get function in "
 			"driver\n");
-		ret = -EINVAL;
+		ret = -ENOTSUPP;
 		goto unlock;
 	}
 
@@ -302,12 +296,8 @@ static void pinconf_dump_pin(struct pinctrl_dev *pctldev,
 static int pinconf_pins_show(struct seq_file *s, void *what)
 {
 	struct pinctrl_dev *pctldev = s->private;
-	const struct pinconf_ops *ops = pctldev->desc->confops;
 	unsigned i, pin;
 
-	if (!ops || !ops->pin_config_get)
-		return 0;
-
 	seq_puts(s, "Pin config settings per pin\n");
 	seq_puts(s, "Format: pin (name): configs\n");
 
@@ -352,13 +342,9 @@ static int pinconf_groups_show(struct seq_file *s, void *what)
 {
 	struct pinctrl_dev *pctldev = s->private;
 	const struct pinctrl_ops *pctlops = pctldev->desc->pctlops;
-	const struct pinconf_ops *ops = pctldev->desc->confops;
 	unsigned ngroups = pctlops->get_groups_count(pctldev);
 	unsigned selector = 0;
 
-	if (!ops || !ops->pin_config_group_get)
-		return 0;
-
 	seq_puts(s, "Pin config settings per pin group\n");
 	seq_puts(s, "Format: group (name): configs\n");
 

drivers/pinctrl/pinctrl-as3722.c

@@ -250,6 +250,26 @@ static int as3722_pinctrl_enable(struct pinctrl_dev *pctldev, unsigned function,
 		return ret;
 	}
 	as_pci->gpio_control[group].io_function = function;
+
+	switch (val) {
+	case AS3722_GPIO_IOSF_SD0_OUT:
+	case AS3722_GPIO_IOSF_PWR_GOOD_OUT:
+	case AS3722_GPIO_IOSF_Q32K_OUT:
+	case AS3722_GPIO_IOSF_PWM_OUT:
+	case AS3722_GPIO_IOSF_SD6_LOW_VOLT_LOW:
+		ret = as3722_update_bits(as_pci->as3722, gpio_cntr_reg,
+			AS3722_GPIO_MODE_MASK, AS3722_GPIO_MODE_OUTPUT_VDDH);
+		if (ret < 0) {
+			dev_err(as_pci->dev, "GPIO%d_CTRL update failed %d\n",
+				group, ret);
+			return ret;
+		}
+		as_pci->gpio_control[group].mode_prop =
+				AS3722_GPIO_MODE_OUTPUT_VDDH;
+		break;
+	default:
+		break;
+	}
 	return ret;
 }
 

drivers/pinctrl/pinctrl-at91.c

@@ -118,7 +118,7 @@ struct at91_pin_group {
 };
 
 /**
- * struct at91_pinctrl_mux_ops - describes an At91 mux ops group
+ * struct at91_pinctrl_mux_ops - describes an AT91 mux ops group
  * on new IP with support for periph C and D the way to mux in
  * periph A and B has changed
  * So provide the right call back
@@ -722,7 +722,8 @@ static int at91_pinconf_get(struct pinctrl_dev *pctldev,
 	unsigned pin;
 	int div;
 
-	dev_dbg(info->dev, "%s:%d, pin_id=%d, config=0x%lx", __func__, __LINE__, pin_id, *config);
+	*config = 0;
+	dev_dbg(info->dev, "%s:%d, pin_id=%d", __func__, __LINE__, pin_id);
 	pio = pin_to_controller(info, pin_to_bank(pin_id));
 	pin = pin_id % MAX_NB_GPIO_PER_BANK;
 
@@ -783,10 +784,35 @@ static int at91_pinconf_set(struct pinctrl_dev *pctldev,
 	return 0;
 }
 
+#define DBG_SHOW_FLAG(flag) do {		\
+	if (config & flag) {			\
+		if (num_conf)			\
+			seq_puts(s, "|");	\
+		seq_puts(s, #flag);		\
+		num_conf++;			\
+	}					\
+} while (0)
+
 static void at91_pinconf_dbg_show(struct pinctrl_dev *pctldev,
 				   struct seq_file *s, unsigned pin_id)
 {
+	unsigned long config;
+	int ret, val, num_conf = 0;
+
+	ret = at91_pinconf_get(pctldev, pin_id, &config);
+
+	DBG_SHOW_FLAG(MULTI_DRIVE);
+	DBG_SHOW_FLAG(PULL_UP);
+	DBG_SHOW_FLAG(PULL_DOWN);
+	DBG_SHOW_FLAG(DIS_SCHMIT);
+	DBG_SHOW_FLAG(DEGLITCH);
+	DBG_SHOW_FLAG(DEBOUNCE);
+	if (config & DEBOUNCE) {
+		val = config >> DEBOUNCE_VAL_SHIFT;
+		seq_printf(s, "(%d)", val);
+	}
 
+	return;
 }
 
 static void at91_pinconf_group_dbg_show(struct pinctrl_dev *pctldev,
@@ -1339,14 +1365,12 @@ void at91_pinctrl_gpio_suspend(void)
 		__raw_writel(backups[i], pio + PIO_IDR);
 		__raw_writel(wakeups[i], pio + PIO_IER);
 
-		if (!wakeups[i]) {
-			clk_unprepare(gpio_chips[i]->clock);
-			clk_disable(gpio_chips[i]->clock);
-		} else {
+		if (!wakeups[i])
+			clk_disable_unprepare(gpio_chips[i]->clock);
+		else
 			printk(KERN_DEBUG "GPIO-%c may wake for %08x\n",
 			       'A'+i, wakeups[i]);
 	}
-	}
 }
 
 void at91_pinctrl_gpio_resume(void)
@@ -1361,10 +1385,8 @@ void at91_pinctrl_gpio_resume(void)
 
 		pio = gpio_chips[i]->regbase;
 
-		if (!wakeups[i]) {
-			if (clk_prepare(gpio_chips[i]->clock) == 0)
-				clk_enable(gpio_chips[i]->clock);
-		}
+		if (!wakeups[i])
+			clk_prepare_enable(gpio_chips[i]->clock);
 
 		__raw_writel(wakeups[i], pio + PIO_IDR);
 		__raw_writel(backups[i], pio + PIO_IER);
@@ -1396,7 +1418,7 @@ static void gpio_irq_handler(unsigned irq, struct irq_desc *desc)
 	chained_irq_enter(chip, desc);
 	for (;;) {
 		/* Reading ISR acks pending (edge triggered) GPIO interrupts.
-		 * When there none are pending, we're finished unless we need
+		 * When there are none pending, we're finished unless we need
 		 * to process multiple banks (like ID_PIOCDE on sam9263).
 		 */
 		isr = readl_relaxed(pio + PIO_ISR) & readl_relaxed(pio + PIO_IMR);
@@ -1505,7 +1527,7 @@ static int at91_gpio_of_irq_setup(struct device_node *node,
 		prev = gpio_chips[at91_gpio->pioc_idx - 1];
 
 	/* The top level handler handles one bank of GPIOs, except
-	 * on some SoC it can handles up to three...
+	 * on some SoC it can handle up to three...
 	 * We only set up the handler for the first of the list.
 	 */
 	if (prev && prev->next == at91_gpio)

drivers/pinctrl/pinctrl-baytrail.c

@@ -285,13 +285,19 @@ static void byt_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
 	spin_lock_irqsave(&vg->lock, flags);
 
 	for (i = 0; i < vg->chip.ngpio; i++) {
+		const char *label;
 		offs = vg->range->pins[i] * 16;
 		conf0 = readl(vg->reg_base + offs + BYT_CONF0_REG);
 		val = readl(vg->reg_base + offs + BYT_VAL_REG);
 
+		label = gpiochip_is_requested(chip, i);
+		if (!label)
+			label = "Unrequested";
+
 		seq_printf(s,
-			   " gpio-%-3d %s %s %s pad-%-3d offset:0x%03x mux:%d %s%s%s\n",
+			   " gpio-%-3d (%-20.20s) %s %s %s pad-%-3d offset:0x%03x mux:%d %s%s%s\n",
 			   i,
+			   label,
 			   val & BYT_INPUT_EN ? "  " : "in",
 			   val & BYT_OUTPUT_EN ? "   " : "out",
 			   val & BYT_LEVEL ? "hi" : "lo",
@@ -365,11 +371,33 @@ static void byt_irq_mask(struct irq_data *d)
 {
 }
 
+static unsigned int byt_irq_startup(struct irq_data *d)
+{
+	struct byt_gpio *vg = irq_data_get_irq_chip_data(d);
+
+	if (gpio_lock_as_irq(&vg->chip, irqd_to_hwirq(d)))
+		dev_err(vg->chip.dev,
+			"unable to lock HW IRQ %lu for IRQ\n",
+			irqd_to_hwirq(d));
+	byt_irq_unmask(d);
+	return 0;
+}
+
+static void byt_irq_shutdown(struct irq_data *d)
+{
+	struct byt_gpio *vg = irq_data_get_irq_chip_data(d);
+
+	byt_irq_mask(d);
+	gpio_unlock_as_irq(&vg->chip, irqd_to_hwirq(d));
+}
+
 static struct irq_chip byt_irqchip = {
 	.name = "BYT-GPIO",
 	.irq_mask = byt_irq_mask,
 	.irq_unmask = byt_irq_unmask,
 	.irq_set_type = byt_irq_type,
+	.irq_startup = byt_irq_startup,
+	.irq_shutdown = byt_irq_shutdown,
 };
 
 static void byt_gpio_irq_init_hw(struct byt_gpio *vg)

drivers/pinctrl/pinctrl-imx1-core.c

@@ -638,6 +638,13 @@ int imx1_pinctrl_core_probe(struct platform_device *pdev,
 		return -EINVAL;
 	}
 
+	ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
+	if (ret) {
+		pinctrl_unregister(ipctl->pctl);
+		dev_err(&pdev->dev, "Failed to populate subdevices\n");
+		return ret;
+	}
+
 	dev_info(&pdev->dev, "initialized IMX pinctrl driver\n");
 
 	return 0;

drivers/pinctrl/pinctrl-msm.h

+/*
+ * Copyright (c) 2013, Sony Mobile Communications AB.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+#ifndef __PINCTRL_MSM_H__
+#define __PINCTRL_MSM_H__
+
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/machine.h>
+
+/**
+ * struct msm_function - a pinmux function
+ * @name:    Name of the pinmux function.
+ * @groups:  List of pingroups for this function.
+ * @ngroups: Number of entries in @groups.
+ */
+struct msm_function {
+	const char *name;
+	const char * const *groups;
+	unsigned ngroups;
+};
+
+/**
+ * struct msm_pingroup - Qualcomm pingroup definition
+ * @name:                 Name of the pingroup.
+ * @pins:	          A list of pins assigned to this pingroup.
+ * @npins:	          Number of entries in @pins.
+ * @funcs:                A list of pinmux functions that can be selected for
+ *                        this group. The index of the selected function is used
+ *                        for programming the function selector.
+ *                        Entries should be indices into the groups list of the
+ *                        struct msm_pinctrl_soc_data.
+ * @ctl_reg:              Offset of the register holding control bits for this group.
+ * @io_reg:               Offset of the register holding input/output bits for this group.
+ * @intr_cfg_reg:         Offset of the register holding interrupt configuration bits.
+ * @intr_status_reg:      Offset of the register holding the status bits for this group.
+ * @intr_target_reg:      Offset of the register specifying routing of the interrupts
+ *                        from this group.
+ * @mux_bit:              Offset in @ctl_reg for the pinmux function selection.
+ * @pull_bit:             Offset in @ctl_reg for the bias configuration.
+ * @drv_bit:              Offset in @ctl_reg for the drive strength configuration.
+ * @oe_bit:               Offset in @ctl_reg for controlling output enable.
+ * @in_bit:               Offset in @io_reg for the input bit value.
+ * @out_bit:              Offset in @io_reg for the output bit value.
+ * @intr_enable_bit:      Offset in @intr_cfg_reg for enabling the interrupt for this group.
+ * @intr_status_bit:      Offset in @intr_status_reg for reading and acking the interrupt
+ *                        status.
+ * @intr_target_bit:      Offset in @intr_target_reg for configuring the interrupt routing.
+ * @intr_raw_status_bit:  Offset in @intr_cfg_reg for the raw status bit.
+ * @intr_polarity_bit:    Offset in @intr_cfg_reg for specifying polarity of the interrupt.
+ * @intr_detection_bit:   Offset in @intr_cfg_reg for specifying interrupt type.
+ * @intr_detection_width: Number of bits used for specifying interrupt type,
+ *                        Should be 2 for SoCs that can detect both edges in hardware,
+ *                        otherwise 1.
+ */
+struct msm_pingroup {
+	const char *name;
+	const unsigned *pins;
+	unsigned npins;
+
+	unsigned funcs[8];
+
+	s16 ctl_reg;
+	s16 io_reg;
+	s16 intr_cfg_reg;
+	s16 intr_status_reg;
+	s16 intr_target_reg;
+
+	unsigned mux_bit:5;
+
+	unsigned pull_bit:5;
+	unsigned drv_bit:5;
+
+	unsigned oe_bit:5;
+	unsigned in_bit:5;
+	unsigned out_bit:5;
+
+	unsigned intr_enable_bit:5;
+	unsigned intr_status_bit:5;
+
+	unsigned intr_target_bit:5;
+	unsigned intr_raw_status_bit:5;
+	unsigned intr_polarity_bit:5;
+	unsigned intr_detection_bit:5;
+	unsigned intr_detection_width:5;
+};
+
+/**
+ * struct msm_pinctrl_soc_data - Qualcomm pin controller driver configuration
+ * @pins:       An array describing all pins the pin controller affects.
+ * @npins:      The number of entries in @pins.
+ * @functions:  An array describing all mux functions the SoC supports.
+ * @nfunctions: The number of entries in @functions.
+ * @groups:     An array describing all pin groups the pin SoC supports.
+ * @ngroups:    The numbmer of entries in @groups.
+ * @ngpio:      The number of pingroups the driver should expose as GPIOs.
+ */
+struct msm_pinctrl_soc_data {
+	const struct pinctrl_pin_desc *pins;
+	unsigned npins;
+	const struct msm_function *functions;
+	unsigned nfunctions;
+	const struct msm_pingroup *groups;
+	unsigned ngroups;
+	unsigned ngpios;
+};
+
+int msm_pinctrl_probe(struct platform_device *pdev,
+		      const struct msm_pinctrl_soc_data *soc_data);
+int msm_pinctrl_remove(struct platform_device *pdev);
+
+#endif

drivers/pinctrl/pinctrl-nomadik.c

@@ -846,14 +846,14 @@ static void nmk_gpio_dbg_show_one(struct seq_file *s,
 		   (mode < 0) ? "unknown" : modes[mode],
 		   pull ? "pull" : "none");
 
-	if (label && !is_out) {
+	if (!is_out) {
 		int irq = gpio_to_irq(gpio);
 		struct irq_desc	*desc = irq_to_desc(irq);
 
 		/* This races with request_irq(), set_irq_type(),
 		 * and set_irq_wake() ... but those are "rare".
 		 */
-		if (irq >= 0 && desc->action) {
+		if (irq > 0 && desc && desc->action) {
 			char *trigger;
 			u32 bitmask = nmk_gpio_get_bitmask(gpio);
 

drivers/pinctrl/pinctrl-single.c

@@ -525,12 +525,18 @@ static void pcs_disable(struct pinctrl_dev *pctldev, unsigned fselector,
 	for (i = 0; i < func->nvals; i++) {
 		struct pcs_func_vals *vals;
 		unsigned long flags;
-		unsigned val;
+		unsigned val, mask;
 
 		vals = &func->vals[i];
 		raw_spin_lock_irqsave(&pcs->lock, flags);
 		val = pcs->read(vals->reg);
-		val &= ~pcs->fmask;
+
+		if (pcs->bits_per_mux)
+			mask = vals->mask;
+		else
+			mask = pcs->fmask;
+
+		val &= ~mask;
 		val |= pcs->foff << pcs->fshift;
 		pcs->write(val, vals->reg);
 		raw_spin_unlock_irqrestore(&pcs->lock, flags);
@@ -1312,6 +1318,14 @@ static int pcs_parse_bits_in_pinctrl_entry(struct pcs_device *pcs,
 			mask_pos = ((pcs->fmask) << (bit_pos - 1));
 			val_pos = val & mask_pos;
 			submask = mask & mask_pos;
+
+			if ((mask & mask_pos) == 0) {
+				dev_err(pcs->dev,
+					"Invalid mask for %s at 0x%x\n",
+					np->name, offset);
+				break;
+			}
+
 			mask &= ~mask_pos;
 
 			if (submask != mask_pos) {

include/linux/mfd/as3722.h

@@ -314,6 +314,7 @@
 #define AS3722_GPIO_IOSF_GPIO_INTERRUPT_IN		AS3722_GPIO_IOSF_VAL(3)
 #define AS3722_GPIO_IOSF_ISINK_PWM_IN			AS3722_GPIO_IOSF_VAL(4)
 #define AS3722_GPIO_IOSF_VOLTAGE_STBY			AS3722_GPIO_IOSF_VAL(5)
+#define AS3722_GPIO_IOSF_SD0_OUT			AS3722_GPIO_IOSF_VAL(6)
 #define AS3722_GPIO_IOSF_PWR_GOOD_OUT			AS3722_GPIO_IOSF_VAL(7)
 #define AS3722_GPIO_IOSF_Q32K_OUT			AS3722_GPIO_IOSF_VAL(8)
 #define AS3722_GPIO_IOSF_WATCHDOG_IN			AS3722_GPIO_IOSF_VAL(9)