[PATCH] sh: PCI updates

This updates some of the PCI drivers.  SH7751, the sh03 board-specific PCI
code, and some ST40 PCI updates are grouped in this.  
Signed-off-by: Paul Mundt <paul.mundt@nokia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

arch/sh/boards/se/7751/io.c

@@ -18,7 +18,7 @@
 #include <asm/addrspace.h>
 
 #include <linux/pci.h>
-#include <asm/pci-sh7751.h>
+#include "../../../drivers/pci/pci-sh7751.h"
 
 #if 0
 /******************************************************************

arch/sh/boards/se/7751/pci.c

@@ -19,7 +19,7 @@
 #include <linux/pci.h>
 
 #include <asm/io.h>
-#include <asm/pci-sh7751.h>
+#include "../../../drivers/pci/pci-sh7751.h"
 
 #define PCIMCR_MRSET_OFF	0xBFFFFFFF
 #define PCIMCR_RFSH_OFF		0xFFFFFFFB

arch/sh/drivers/pci/Makefile

@@ -13,4 +13,4 @@ obj-$(CONFIG_SH_DREAMCAST)		+= ops-dreamcast.o fixups-dreamcast.o \
 obj-$(CONFIG_SH_SECUREEDGE5410)		+= ops-snapgear.o
 obj-$(CONFIG_SH_BIGSUR)			+= ops-bigsur.o
 obj-$(CONFIG_SH_RTS7751R2D)		+= ops-rts7751r2d.o fixups-rts7751r2d.o
-
+obj-$(CONFIG_SH_SH03)			+= ops-sh03.o fixups-sh03.o

arch/sh/drivers/pci/fixups-rts7751r2d.c

@@ -18,15 +18,26 @@
 
 int pci_fixup_pcic(void)
 {
-	unsigned long mcr;
+	unsigned long bcr1, mcr;
 
-	outl(0xfb900047, SH7751_PCICONF1);
-	outl(0xab000001, SH7751_PCICONF4);
+	bcr1 = inl(SH7751_BCR1);
+	bcr1 |= 0x40080000;	/* Enable Bit 19 BREQEN, set PCIC to slave */
+	outl(bcr1, PCI_REG(SH7751_PCIBCR1));
+
+	/* Enable all interrupts, so we known what to fix */
+	outl(0x0000c3ff, PCI_REG(SH7751_PCIINTM));
+	outl(0x0000380f, PCI_REG(SH7751_PCIAINTM));
+
+	outl(0xfb900047, PCI_REG(SH7751_PCICONF1));
+	outl(0xab000001, PCI_REG(SH7751_PCICONF4));
 
 	mcr = inl(SH7751_MCR);
 	mcr = (mcr & PCIMCR_MRSET_OFF) & PCIMCR_RFSH_OFF;
-	outl(mcr, SH7751_PCIMCR);
+	outl(mcr, PCI_REG(SH7751_PCIMCR));
 
+	outl(0x0c000000, PCI_REG(SH7751_PCICONF5));
+	outl(0xd0000000, PCI_REG(SH7751_PCICONF6));
+	outl(0x0c000000, PCI_REG(SH7751_PCILAR0));
+	outl(0x00000000, PCI_REG(SH7751_PCILAR1));
 	return 0;
 }
-

arch/sh/drivers/pci/fixups-sh03.c

+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/pci.h>
+
+/*
+ * 	IRQ functions
+ */
+
+int __init pcibios_map_platform_irq(u8 slot, u8 pin, struct pci_dev *dev)
+{
+	int irq;
+
+	if (dev->bus->number == 0) {
+		switch (slot) {
+		case 4: return 5;	/* eth0       */
+		case 8: return 5;	/* eth1       */
+		case 6: return 2;	/* PCI bridge */
+		default:
+                	printk("PCI: Bad IRQ mapping request for slot %d\n", slot);
+                	return 2;
+		}
+	} else {
+		switch (pin) {
+		case 0:   irq =  2; break;
+		case 1:   irq =  2; break;
+		case 2:   irq =  2; break;
+		case 3:   irq =  2; break;
+		case 4:   irq =  2; break;
+		default:  irq = -1; break;
+		}
+	}
+	return irq;
+}
+
+static u8 __init sh03_no_swizzle(struct pci_dev *dev, u8 *pin)
+{
+	/* no swizzling */
+	return PCI_SLOT(dev->devfn);
+}
+
+static int sh03_pci_lookup_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+	int irq = -1;
+
+	/* now lookup the actual IRQ on a platform specific basis (pci-'platform'.c) */
+	irq = pcibios_map_platform_irq(slot, pin, dev);
+	if( irq < 0 ) {
+		pr_debug("PCI: Error mapping IRQ on device %s\n", dev->slot_name);
+		return irq;
+	}
+
+	pr_debug("Setting IRQ for slot %s to %d\n", dev->slot_name, irq);
+
+	return irq;
+}
+
+void __init pcibios_fixup_irqs(void)
+{
+	pci_fixup_irqs(sh03_no_swizzle, sh03_pci_lookup_irq);
+}

arch/sh/drivers/pci/ops-rts7751r2d.c

@@ -61,7 +61,12 @@ EXPORT_SYMBOL(board_pci_channels);
 static struct sh7751_pci_address_map sh7751_pci_map = {
 	.window0	= {
 		.base	= SH7751_CS3_BASE_ADDR,
-		.size	= 0x03f00000,
+		.size	= 0x04000000,
+	},
+
+	.window1	= {
+		.base	= 0x00000000,	/* Unused */
+		.size	= 0x00000000,	/* Unused */
 	},
 
 	.flags	= SH7751_PCIC_NO_RESET,

arch/sh/drivers/pci/ops-sh03.c

+/*
+ * linux/arch/sh/drivers/pci/ops-sh03.c
+ *
+ * PCI initialization for the Interface CTP/PCI-SH03 board
+ */
+
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+#include <asm/io.h>
+#include "pci-sh7751.h"
+
+/*
+ * Description:  This function sets up and initializes the pcic, sets
+ * up the BARS, maps the DRAM into the address space etc, etc.
+ */
+int __init pcibios_init_platform(void)
+{
+   return 1;
+}
+
+static struct resource sh7751_io_resource = {
+	.name   = "SH03 IO",
+	.start  = SH7751_PCI_IO_BASE,
+	.end    = SH7751_PCI_IO_BASE + SH7751_PCI_IO_SIZE - 1,
+	.flags  = IORESOURCE_IO
+};
+
+static struct resource sh7751_mem_resource = {
+	.name   = "SH03 mem",
+	.start  = SH7751_PCI_MEMORY_BASE,
+	.end    = SH7751_PCI_MEMORY_BASE + SH7751_PCI_MEM_SIZE - 1,
+	.flags  = IORESOURCE_MEM
+};
+
+extern struct pci_ops sh7751_pci_ops;
+
+struct pci_channel board_pci_channels[] = {
+	{ &sh7751_pci_ops, &sh7751_io_resource, &sh7751_mem_resource, 0, 0xff },
+	{ NULL, NULL, NULL, 0, 0 },
+};
+

arch/sh/drivers/pci/pci-auto.c

@@ -524,8 +524,10 @@ pciauto_bus_scan(struct pci_channel *hose, int top_bus, int current_bus)
 					 PCI_COMMAND, cmdstat | PCI_COMMAND_IO |
 					 PCI_COMMAND_MEMORY |
 					 PCI_COMMAND_MASTER);
+#if !defined(CONFIG_SH_HS7751RVOIP) && !defined(CONFIG_SH_RTS7751R2D)
 		early_write_config_byte(hose, top_bus, current_bus, pci_devfn,
 					PCI_LATENCY_TIMER, 0x80);
+#endif
 
 		/* Allocate PCI I/O and/or memory space */
 		pciauto_setup_bars(hose, top_bus, current_bus, pci_devfn, PCI_BASE_ADDRESS_5);

arch/sh/drivers/pci/pci-sh7751.c

@@ -33,6 +33,8 @@
 static unsigned int pci_probe = PCI_PROBE_CONF1;
 extern int pci_fixup_pcic(void);
 
+void pcibios_fixup_irqs(void) __attribute__ ((weak));
+
 /*
  * Direct access to PCI hardware...
  */
@@ -158,7 +160,6 @@ static int __init pci_check_direct(void)
  *  Handle bus scanning and fixups ....
  */
 
-#if !defined(CONFIG_SH_HS7751RVOIP) && !defined(CONFIG_SH_RTS7751R2D)
 static void __init pci_fixup_ide_bases(struct pci_dev *d)
 {
 	int i;
@@ -256,7 +257,7 @@ int __init sh7751_pcic_init(struct sh7751_pci_address_map *map)
 	outl(0, PCI_REG(SH7751_PCICLKR));
 	/* Clear Powerdown IRQ's (not done in reset) */
 	word = SH7751_PCIPINT_D3 | SH7751_PCIPINT_D0;
-	outl(word, PCI_REG(SH7751_PCICLKR));
+	outl(word, PCI_REG(SH7751_PCIPINT));
 
 	/*
 	 * This code is unused for some boards as it is done in the

arch/sh/drivers/pci/pci-st40.h

@@ -33,13 +33,36 @@
 #define ST40PCI_LAR0          0x1c
 
 #define ST40PCI_INT           0x24
+#define INT_MNLTDIM           (1<<15)
+#define INT_TTADI             (1<<14)
+#define INT_TMTO              (1<<9)
+#define INT_MDEI              (1<<8)
+#define INT_APEDI             (1<<7)
+#define INT_SDI               (1<<6)
+#define INT_DPEITW            (1<<5)
+#define INT_PEDITR            (1<<4)
+#define INT_TADIM             (1<<3)
 #define INT_MADIM             (1<<2)
+#define INT_MWPDI             (1<<1)
+#define INT_MRDPEI            (1<<0)
 
 
 #define ST40PCI_INTM          0x28
 #define ST40PCI_AIR           0x2c
+
 #define ST40PCI_CIR           0x30
+#define CIR_PIOTEM            (1<<31)
+#define CIR_RWTET             (1<<26)
+
 #define ST40PCI_AINT          0x40
+#define AINT_MBI              (1<<13)
+#define AINT_TBTOI            (1<<12)
+#define AINT_MBTOI            (1<<11)
+#define AINT_TAI              (1<<3)
+#define AINT_MAI              (1<<2)
+#define AINT_RDPEI            (1<<1)
+#define AINT_WDPE             (1<<0)
+
 #define ST40PCI_AINTM         0x44
 #define ST40PCI_BMIR          0x48
 #define ST40PCI_PAR           0x4c
@@ -51,6 +74,53 @@
 #define ST40PCI_IOBMR         0x74
 #define ST40PCI_PDR           0x78
 
+/* H8 specific registers start here */
+#define ST40PCI_WCBAR         0x7c
+#define ST40PCI_LOCCFG_UNLOCK 0x34
+
+#define ST40PCI_RBAR0         0x100
+#define ST40PCI_RSR0          0x104
+#define ST40PCI_RLAR0         0x108
+
+#define ST40PCI_RBAR1         0x110
+#define ST40PCI_RSR1          0x114
+#define ST40PCI_RLAR1         0x118
+
+
+#define ST40PCI_RBAR2         0x120
+#define ST40PCI_RSR2          0x124
+#define ST40PCI_RLAR2         0x128
+
+#define ST40PCI_RBAR3         0x130
+#define ST40PCI_RSR3          0x134
+#define ST40PCI_RLAR3         0x138
+
+#define ST40PCI_RBAR4         0x140
+#define ST40PCI_RSR4          0x144
+#define ST40PCI_RLAR4         0x148
+
+#define ST40PCI_RBAR5         0x150
+#define ST40PCI_RSR5          0x154
+#define ST40PCI_RLAR5         0x158
+
+#define ST40PCI_RBAR6         0x160
+#define ST40PCI_RSR6          0x164
+#define ST40PCI_RLAR6         0x168
+
+#define ST40PCI_RBAR7         0x170
+#define ST40PCI_RSR7          0x174
+#define ST40PCI_RLAR7         0x178
+
+
+#define ST40PCI_RBAR(n)      (0x100+(0x10*(n)))
+#define ST40PCI_RSR(n)       (0x104+(0x10*(n)))
+#define ST40PCI_RLAR(n)      (0x108+(0x10*(n)))
+
+#define ST40PCI_PERF               0x80
+#define PERF_MASTER_WRITE_POSTING  (1<<4)
+/* H8 specific registers end here */
+
+
 /* These are configs space registers */
 #define ST40PCI_CSR_VID               0x10000
 #define ST40PCI_CSR_DID               0x10002

arch/sh/drivers/pci/pci.c

@@ -106,6 +106,8 @@ int pcibios_enable_device(struct pci_dev *dev, int mask)
 	pci_read_config_word(dev, PCI_COMMAND, &cmd);
 	old_cmd = cmd;
 	for(idx=0; idx<6; idx++) {
+		if (!(mask & (1 << idx)))
+			continue;
 		r = &dev->resource[idx];
 		if (!r->start && r->end) {
 			printk(KERN_ERR "PCI: Device %s not available because "