Merge branch 'samsung/cleanup' into next/drivers

Dependency for the samsung/drivers branch

Conflicts:
	arch/arm/mach-exynos/Makefile
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/arm/insignal-boards.txt

+* Insignal's Exynos4210 based Origen evaluation board
+
+Origen low-cost evaluation board is based on Samsung's Exynos4210 SoC.
+
+Required root node properties:
+    - compatible = should be one or more of the following.
+        (a) "samsung,smdkv310" - for Samsung's SMDKV310 eval board.
+        (b) "samsung,exynos4210"  - for boards based on Exynos4210 SoC.

Documentation/devicetree/bindings/arm/samsung-boards.txt

+* Samsung's Exynos4210 based SMDKV310 evaluation board
+
+SMDKV310 evaluation board is based on Samsung's Exynos4210 SoC.
+
+Required root node properties:
+    - compatible = should be one or more of the following.
+        (a) "samsung,smdkv310" - for Samsung's SMDKV310 eval board.
+        (b) "samsung,exynos4210"  - for boards based on Exynos4210 SoC.

Documentation/devicetree/bindings/dma/arm-pl330.txt

+* ARM PrimeCell PL330 DMA Controller
+
+The ARM PrimeCell PL330 DMA controller can move blocks of memory contents
+between memory and peripherals or memory to memory.
+
+Required properties:
+  - compatible: should include both "arm,pl330" and "arm,primecell".
+  - reg: physical base address of the controller and length of memory mapped
+    region.
+  - interrupts: interrupt number to the cpu.
+
+Example:
+
+	pdma0: pdma@12680000 {
+		compatible = "arm,pl330", "arm,primecell";
+		reg = <0x12680000 0x1000>;
+		interrupts = <99>;
+	};
+
+Client drivers (device nodes requiring dma transfers from dev-to-mem or
+mem-to-dev) should specify the DMA channel numbers using a two-value pair
+as shown below.
+
+  [property name]  = <[phandle of the dma controller] [dma request id]>;
+
+      where 'dma request id' is the dma request number which is connected
+      to the client controller. The 'property name' is recommended to be
+      of the form <name>-dma-channel.
+
+  Example:  tx-dma-channel = <&pdma0 12>;

Documentation/devicetree/bindings/gpio/gpio-samsung.txt

+Samsung Exynos4 GPIO Controller
+
+Required properties:
+- compatible: Compatible property value should be "samsung,exynos4-gpio>".
+
+- reg: Physical base address of the controller and length of memory mapped
+  region.
+
+- #gpio-cells: Should be 4. The syntax of the gpio specifier used by client nodes
+  should be the following with values derived from the SoC user manual.
+     <[phandle of the gpio controller node]
+      [pin number within the gpio controller]
+      [mux function]
+      [pull up/down]
+      [drive strength]>
+
+  Values for gpio specifier:
+  - Pin number: is a value between 0 to 7.
+  - Pull Up/Down: 0 - Pull Up/Down Disabled.
+                  1 - Pull Down Enabled.
+                  3 - Pull Up Enabled.
+  - Drive Strength: 0 - 1x,
+                    1 - 3x,
+                    2 - 2x,
+                    3 - 4x
+
+- gpio-controller: Specifies that the node is a gpio controller.
+- #address-cells: should be 1.
+- #size-cells: should be 1.
+
+Example:
+
+	gpa0: gpio-controller@11400000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "samsung,exynos4-gpio";
+		reg = <0x11400000 0x20>;
+		#gpio-cells = <4>;
+		gpio-controller;
+	};

Documentation/devicetree/bindings/input/samsung-keypad.txt

+* Samsung's Keypad Controller device tree bindings
+
+Samsung's Keypad controller is used to interface a SoC with a matrix-type
+keypad device. The keypad controller supports multiple row and column lines.
+A key can be placed at each intersection of a unique row and a unique column.
+The keypad controller can sense a key-press and key-release and report the
+event using a interrupt to the cpu.
+
+Required SoC Specific Properties:
+- compatible: should be one of the following
+  - "samsung,s3c6410-keypad": For controllers compatible with s3c6410 keypad
+    controller.
+  - "samsung,s5pv210-keypad": For controllers compatible with s5pv210 keypad
+    controller.
+
+- reg: physical base address of the controller and length of memory mapped
+  region.
+
+- interrupts: The interrupt number to the cpu.
+
+Required Board Specific Properties:
+- samsung,keypad-num-rows: Number of row lines connected to the keypad
+  controller.
+
+- samsung,keypad-num-columns: Number of column lines connected to the
+  keypad controller.
+
+- row-gpios: List of gpios used as row lines. The gpio specifier for
+  this property depends on the gpio controller to which these row lines
+  are connected.
+
+- col-gpios: List of gpios used as column lines. The gpio specifier for
+  this property depends on the gpio controller to which these column
+  lines are connected.
+
+- Keys represented as child nodes: Each key connected to the keypad
+  controller is represented as a child node to the keypad controller
+  device node and should include the following properties.
+  - keypad,row: the row number to which the key is connected.
+  - keypad,column: the column number to which the key is connected.
+  - linux,code: the key-code to be reported when the key is pressed
+    and released.
+
+Optional Properties specific to linux:
+- linux,keypad-no-autorepeat: do no enable autorepeat feature.
+- linux,keypad-wakeup: use any event on keypad as wakeup event.
+
+
+Example:
+	keypad@100A0000 {
+		compatible = "samsung,s5pv210-keypad";
+		reg = <0x100A0000 0x100>;
+		interrupts = <173>;
+		samsung,keypad-num-rows = <2>;
+		samsung,keypad-num-columns = <8>;
+		linux,input-no-autorepeat;
+		linux,input-wakeup;
+
+		row-gpios = <&gpx2 0 3 3 0
+			     &gpx2 1 3 3 0>;
+
+		col-gpios = <&gpx1 0 3 0 0
+			     &gpx1 1 3 0 0
+			     &gpx1 2 3 0 0
+			     &gpx1 3 3 0 0
+			     &gpx1 4 3 0 0
+			     &gpx1 5 3 0 0
+			     &gpx1 6 3 0 0
+			     &gpx1 7 3 0 0>;
+
+		key_1 {
+			keypad,row = <0>;
+			keypad,column = <3>;
+			linux,code = <2>;
+		};
+
+		key_2 {
+			keypad,row = <0>;
+			keypad,column = <4>;
+			linux,code = <3>;
+		};
+
+		key_3 {
+			keypad,row = <0>;
+			keypad,column = <5>;
+			linux,code = <4>;
+		};
+	};

Documentation/devicetree/bindings/rtc/s3c-rtc.txt

+* Samsung's S3C Real Time Clock controller
+
+Required properties:
+- compatible: should be one of the following.
+    * "samsung,s3c2410-rtc" - for controllers compatible with s3c2410 rtc.
+    * "samsung,s3c6410-rtc" - for controllers compatible with s3c6410 rtc.
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- interrupts: Two interrupt numbers to the cpu should be specified. First
+  interrupt number is the rtc alarm interupt and second interrupt number
+  is the rtc tick interrupt. The number of cells representing a interrupt
+  depends on the parent interrupt controller.
+
+Example:
+
+	rtc@10070000 {
+		compatible = "samsung,s3c6410-rtc";
+		reg = <0x10070000 0x100>;
+		interrupts = <44 0 45 0>;
+	};

Documentation/devicetree/bindings/serial/samsung_uart.txt

+* Samsung's UART Controller
+
+The Samsung's UART controller is used for interfacing SoC with serial communicaion
+devices.
+
+Required properties:
+- compatible: should be
+  - "samsung,exynos4210-uart", for UART's compatible with Exynos4210 uart ports.
+
+- reg: base physical address of the controller and length of memory mapped
+  region.
+
+- interrupts: interrupt number to the cpu. The interrupt specifier format depends
+  on the interrupt controller parent.

arch/arm/boot/dts/exynos4210-origen.dts

+/*
+ * Samsung's Exynos4210 based Origen board device tree source
+ *
+ * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2010-2011 Linaro Ltd.
+ *		www.linaro.org
+ *
+ * Device tree source file for Insignal's Origen board which is based on
+ * Samsung's Exynos4210 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+/include/ "exynos4210.dtsi"
+
+/ {
+	model = "Insignal Origen evaluation board based on Exynos4210";
+	compatible = "insignal,origen", "samsung,exynos4210";
+
+	memory {
+		reg = <0x40000000 0x40000000>;
+	};
+
+	chosen {
+		bootargs ="root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M console=ttySAC2,115200 init=/linuxrc";
+	};
+
+	sdhci@12530000 {
+		samsung,sdhci-bus-width = <4>;
+		linux,mmc_cap_4_bit_data;
+		samsung,sdhci-cd-internal;
+		gpio-cd = <&gpk2 2 2 3 3>;
+		gpios = <&gpk2 0 2 0 3>,
+			<&gpk2 1 2 0 3>,
+			<&gpk2 3 2 3 3>,
+			<&gpk2 4 2 3 3>,
+			<&gpk2 5 2 3 3>,
+			<&gpk2 6 2 3 3>;
+	};
+
+	sdhci@12510000 {
+		samsung,sdhci-bus-width = <4>;
+		linux,mmc_cap_4_bit_data;
+		samsung,sdhci-cd-internal;
+		gpio-cd = <&gpk0 2 2 3 3>;
+		gpios = <&gpk0 0 2 0 3>,
+			<&gpk0 1 2 0 3>,
+			<&gpk0 3 2 3 3>,
+			<&gpk0 4 2 3 3>,
+			<&gpk0 5 2 3 3>,
+			<&gpk0 6 2 3 3>;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		up {
+			label = "Up";
+			gpios = <&gpx2 0 0 0 2>;
+			linux,code = <103>;
+		};
+
+		down {
+			label = "Down";
+			gpios = <&gpx2 1 0 0 2>;
+			linux,code = <108>;
+		};
+
+		back {
+			label = "Back";
+			gpios = <&gpx1 7 0 0 2>;
+			linux,code = <158>;
+		};
+
+		home {
+			label = "Home";
+			gpios = <&gpx1 6 0 0 2>;
+			linux,code = <102>;
+		};
+
+		menu {
+			label = "Menu";
+			gpios = <&gpx1 5 0 0 2>;
+			linux,code = <139>;
+		};
+	};
+
+	keypad@100A0000 {
+		status = "disabled";
+	};
+
+	sdhci@12520000 {
+		status = "disabled";
+	};
+
+	sdhci@12540000 {
+		status = "disabled";
+	};
+
+	i2c@13860000 {
+		status = "disabled";
+	};
+
+	i2c@13870000 {
+		status = "disabled";
+	};
+
+	i2c@13880000 {
+		status = "disabled";
+	};
+
+	i2c@13890000 {
+		status = "disabled";
+	};
+
+	i2c@138A0000 {
+		status = "disabled";
+	};
+
+	i2c@138B0000 {
+		status = "disabled";
+	};
+
+	i2c@138C0000 {
+		status = "disabled";
+	};
+
+	i2c@138D0000 {
+		status = "disabled";
+	};
+};

arch/arm/boot/dts/exynos4210-smdkv310.dts

+/*
+ * Samsung's Exynos4210 based SMDKV310 board device tree source
+ *
+ * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2010-2011 Linaro Ltd.
+ *		www.linaro.org
+ *
+ * Device tree source file for Samsung's SMDKV310 board which is based on
+ * Samsung's Exynos4210 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+/include/ "exynos4210.dtsi"
+
+/ {
+	model = "Samsung smdkv310 evaluation board based on Exynos4210";
+	compatible = "samsung,smdkv310", "samsung,exynos4210";
+
+	memory {
+		reg = <0x40000000 0x80000000>;
+	};
+
+	chosen {
+		bootargs = "root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M console=ttySAC1,115200 init=/linuxrc";
+	};
+
+	sdhci@12530000 {
+		samsung,sdhci-bus-width = <4>;
+		linux,mmc_cap_4_bit_data;
+		samsung,sdhci-cd-internal;
+		gpio-cd = <&gpk2 2 2 3 3>;
+		gpios = <&gpk2 0 2 0 3>,
+			<&gpk2 1 2 0 3>,
+			<&gpk2 3 2 3 3>,
+			<&gpk2 4 2 3 3>,
+			<&gpk2 5 2 3 3>,
+			<&gpk2 6 2 3 3>;
+	};
+
+	keypad@100A0000 {
+		samsung,keypad-num-rows = <2>;
+		samsung,keypad-num-columns = <8>;
+		linux,keypad-no-autorepeat;
+		linux,keypad-wakeup;
+
+		row-gpios = <&gpx2 0 3 3 0>,
+			    <&gpx2 1 3 3 0>;
+
+		col-gpios = <&gpx1 0 3 0 0>,
+			    <&gpx1 1 3 0 0>,
+			    <&gpx1 2 3 0 0>,
+			    <&gpx1 3 3 0 0>,
+			    <&gpx1 4 3 0 0>,
+			    <&gpx1 5 3 0 0>,
+			    <&gpx1 6 3 0 0>,
+			    <&gpx1 7 3 0 0>;
+
+		key_1 {
+			keypad,row = <0>;
+			keypad,column = <3>;
+			linux,code = <2>;
+		};
+
+		key_2 {
+			keypad,row = <0>;
+			keypad,column = <4>;
+			linux,code = <3>;
+		};
+
+		key_3 {
+			keypad,row = <0>;
+			keypad,column = <5>;
+			linux,code = <4>;
+		};
+
+		key_4 {
+			keypad,row = <0>;
+			keypad,column = <6>;
+			linux,code = <5>;
+		};
+
+		key_5 {
+			keypad,row = <0>;
+			keypad,column = <7>;
+			linux,code = <6>;
+		};
+
+		key_a {
+			keypad,row = <1>;
+			keypad,column = <3>;
+			linux,code = <30>;
+		};
+
+		key_b {
+			keypad,row = <1>;
+			keypad,column = <4>;
+			linux,code = <48>;
+		};
+
+		key_c {
+			keypad,row = <1>;
+			keypad,column = <5>;
+			linux,code = <46>;
+		};
+
+		key_d {
+			keypad,row = <1>;
+			keypad,column = <6>;
+			linux,code = <32>;
+		};
+
+		key_e {
+			keypad,row = <1>;
+			keypad,column = <7>;
+			linux,code = <18>;
+		};
+	};
+
+	i2c@13860000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <20000>;
+		gpios = <&gpd1 0 2 3 0>,
+			<&gpd1 1 2 3 0>;
+
+		eeprom@50 {
+			compatible = "samsung,24ad0xd1";
+			reg = <0x50>;
+		};
+
+		eeprom@52 {
+			compatible = "samsung,24ad0xd1";
+			reg = <0x52>;
+		};
+	};
+
+	sdhci@12510000 {
+		status = "disabled";
+	};
+
+	sdhci@12520000 {
+		status = "disabled";
+	};
+
+	sdhci@12540000 {
+		status = "disabled";
+	};
+
+	i2c@13870000 {
+		status = "disabled";
+	};
+
+	i2c@13880000 {
+		status = "disabled";
+	};
+
+	i2c@13890000 {
+		status = "disabled";
+	};
+
+	i2c@138A0000 {
+		status = "disabled";
+	};
+
+	i2c@138B0000 {
+		status = "disabled";
+	};
+
+	i2c@138C0000 {
+		status = "disabled";
+	};
+
+	i2c@138D0000 {
+		status = "disabled";
+	};
+};

arch/arm/boot/dts/exynos4210.dtsi

+/*
+ * Samsung's Exynos4210 SoC device tree source
+ *
+ * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2010-2011 Linaro Ltd.
+ *		www.linaro.org
+ *
+ * Samsung's Exynos4210 SoC device nodes are listed in this file. Exynos4210
+ * based board files can include this file and provide values for board specfic
+ * bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * Exynos4210 SoC. As device tree coverage for Exynos4210 increases, additional
+ * nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/include/ "skeleton.dtsi"
+
+/ {
+	compatible = "samsung,exynos4210";
+	interrupt-parent = <&gic>;
+
+	gic:interrupt-controller@10490000 {
+		compatible = "arm,cortex-a9-gic";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0x10490000 0x1000>, <0x10480000 0x100>;
+	};
+
+	watchdog@10060000 {
+		compatible = "samsung,s3c2410-wdt";
+		reg = <0x10060000 0x100>;
+		interrupts = <0 43 0>;
+	};
+
+	rtc@10070000 {
+		compatible = "samsung,s3c6410-rtc";
+		reg = <0x10070000 0x100>;
+		interrupts = <0 44 0>, <0 45 0>;
+	};
+
+	keypad@100A0000 {
+		compatible = "samsung,s5pv210-keypad";
+		reg = <0x100A0000 0x100>;
+		interrupts = <0 109 0>;
+	};
+
+	sdhci@12510000 {
+		compatible = "samsung,exynos4210-sdhci";
+		reg = <0x12510000 0x100>;
+		interrupts = <0 73 0>;
+	};
+
+	sdhci@12520000 {
+		compatible = "samsung,exynos4210-sdhci";
+		reg = <0x12520000 0x100>;
+		interrupts = <0 74 0>;
+	};
+
+	sdhci@12530000 {
+		compatible = "samsung,exynos4210-sdhci";
+		reg = <0x12530000 0x100>;
+		interrupts = <0 75 0>;
+	};
+
+	sdhci@12540000 {
+		compatible = "samsung,exynos4210-sdhci";
+		reg = <0x12540000 0x100>;
+		interrupts = <0 76 0>;
+	};
+
+	serial@13800000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x13800000 0x100>;
+		interrupts = <0 52 0>;
+	};
+
+	serial@13810000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x13810000 0x100>;
+		interrupts = <0 53 0>;
+	};
+
+	serial@13820000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x13820000 0x100>;
+		interrupts = <0 54 0>;
+	};
+
+	serial@13830000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x13830000 0x100>;
+		interrupts = <0 55 0>;
+	};
+
+	i2c@13860000 {
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x13860000 0x100>;
+		interrupts = <0 58 0>;
+	};
+
+	i2c@13870000 {
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x13870000 0x100>;
+		interrupts = <0 59 0>;
+	};
+
+	i2c@13880000 {
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x13880000 0x100>;
+		interrupts = <0 60 0>;
+	};
+
+	i2c@13890000 {
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x13890000 0x100>;
+		interrupts = <0 61 0>;
+	};
+
+	i2c@138A0000 {
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x138A0000 0x100>;
+		interrupts = <0 62 0>;
+	};
+
+	i2c@138B0000 {
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x138B0000 0x100>;
+		interrupts = <0 63 0>;
+	};
+
+	i2c@138C0000 {
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x138C0000 0x100>;
+		interrupts = <0 64 0>;
+	};
+
+	i2c@138D0000 {
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x138D0000 0x100>;
+		interrupts = <0 65 0>;
+	};
+
+	amba {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "arm,amba-bus";
+		interrupt-parent = <&gic>;
+		ranges;
+
+		pdma0: pdma@12680000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x12680000 0x1000>;
+			interrupts = <0 35 0>;
+		};
+
+		pdma1: pdma@12690000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x12690000 0x1000>;
+			interrupts = <0 36 0>;
+		};
+	};
+
+	gpio-controllers {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		gpio-controller;
+		ranges;
+
+		gpa0: gpio-controller@11400000 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400000 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpa1: gpio-controller@11400020 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400020 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpb: gpio-controller@11400040 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400040 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpc0: gpio-controller@11400060 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400060 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpc1: gpio-controller@11400080 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400080 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpd0: gpio-controller@114000A0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x114000A0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpd1: gpio-controller@114000C0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x114000C0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpe0: gpio-controller@114000E0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x114000E0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpe1: gpio-controller@11400100 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400100 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpe2: gpio-controller@11400120 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400120 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpe3: gpio-controller@11400140 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400140 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpe4: gpio-controller@11400160 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400160 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpf0: gpio-controller@11400180 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400180 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpf1: gpio-controller@114001A0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x114001A0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpf2: gpio-controller@114001C0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x114001C0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpf3: gpio-controller@114001E0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x114001E0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpj0: gpio-controller@11000000 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000000 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpj1: gpio-controller@11000020 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000020 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpk0: gpio-controller@11000040 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000040 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpk1: gpio-controller@11000060 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000060 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpk2: gpio-controller@11000080 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000080 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpk3: gpio-controller@110000A0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x110000A0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpl0: gpio-controller@110000C0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x110000C0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpl1: gpio-controller@110000E0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x110000E0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpl2: gpio-controller@11000100 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000100 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpy0: gpio-controller@11000120 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000120 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpy1: gpio-controller@11000140 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000140 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpy2: gpio-controller@11000160 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000160 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpy3: gpio-controller@11000180 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000180 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpy4: gpio-controller@110001A0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x110001A0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpy5: gpio-controller@110001C0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x110001C0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpy6: gpio-controller@110001E0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x110001E0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpx0: gpio-controller@11000C00 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000C00 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpx1: gpio-controller@11000C20 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000C20 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpx2: gpio-controller@11000C40 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000C40 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpx3: gpio-controller@11000C60 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000C60 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpz: gpio-controller@03860000 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x03860000 0x20>;
+			#gpio-cells = <4>;
+		};
+	};
+};

arch/arm/mach-exynos/Kconfig

@@ -57,6 +57,11 @@ config EXYNOS4_MCT
 	help
 	  Use MCT (Multi Core Timer) as kernel timers
 
+config EXYNOS4_DEV_DMA
+	bool
+	help
+	  Compile in amba device definitions for DMA controller
+
 config EXYNOS4_DEV_AHCI
 	bool
 	help
@@ -182,6 +187,7 @@ config MACH_SMDKV310
 	select SAMSUNG_DEV_BACKLIGHT
 	select EXYNOS4_DEV_AHCI
 	select SAMSUNG_DEV_KEYPAD
+	select EXYNOS4_DEV_DMA
 	select EXYNOS4_DEV_PD
 	select SAMSUNG_DEV_PWM
 	select EXYNOS4_DEV_USB_OHCI
@@ -203,6 +209,7 @@ config MACH_ARMLEX4210
 	select S3C_DEV_HSMMC2
 	select S3C_DEV_HSMMC3
 	select EXYNOS4_DEV_AHCI
+	select EXYNOS4_DEV_DMA
 	select EXYNOS4_DEV_SYSMMU
 	select EXYNOS4_SETUP_SDHCI
 	help
@@ -228,6 +235,7 @@ config MACH_UNIVERSAL_C210
 	select S5P_DEV_MFC
 	select S5P_DEV_ONENAND
 	select S5P_DEV_TV
+	select EXYNOS4_DEV_DMA
 	select EXYNOS4_DEV_PD
 	select EXYNOS4_SETUP_FIMD0
 	select EXYNOS4_SETUP_I2C1
@@ -261,6 +269,7 @@ config MACH_NURI
 	select S5P_DEV_MFC
 	select S5P_DEV_USB_EHCI
 	select S5P_SETUP_MIPIPHY
+	select EXYNOS4_DEV_DMA
 	select EXYNOS4_DEV_PD
 	select EXYNOS4_SETUP_FIMC
 	select EXYNOS4_SETUP_FIMD0
@@ -293,6 +302,7 @@ config MACH_ORIGEN
 	select S5P_DEV_USB_EHCI
 	select SAMSUNG_DEV_BACKLIGHT
 	select SAMSUNG_DEV_PWM
+	select EXYNOS4_DEV_DMA
 	select EXYNOS4_DEV_PD
 	select EXYNOS4_DEV_USB_OHCI
 	select EXYNOS4_SETUP_FIMD0
@@ -334,6 +344,20 @@ config MACH_SMDK4412
 	  Machine support for Samsung SMDK4412
 endif
 
+comment "Flattened Device Tree based board for Exynos4 based SoC"
+
+config MACH_EXYNOS4_DT
+	bool "Samsung Exynos4 Machine using device tree"
+	select CPU_EXYNOS4210
+	select USE_OF
+	select ARM_AMBA
+	select HAVE_SAMSUNG_KEYPAD if INPUT_KEYBOARD
+	help
+	  Machine support for Samsung Exynos4 machine with device tree enabled.
+	  Select this if a fdt blob is available for the Exynos4 SoC based board.
+	  Note: This is under development and not all peripherals can be supported
+	  with this machine file.
+
 if ARCH_EXYNOS4
 
 comment "Configuration for HSMMC 8-bit bus width"

arch/arm/mach-exynos/Makefile

@@ -13,7 +13,7 @@ obj-				:=
 # Core support for EXYNOS4 system
 
 obj-$(CONFIG_ARCH_EXYNOS4)	+= cpu.o init.o clock.o irq-combiner.o setup-i2c0.o
-obj-$(CONFIG_ARCH_EXYNOS4)	+= irq-eint.o dma.o pmu.o
+obj-$(CONFIG_ARCH_EXYNOS4)	+= irq-eint.o pmu.o
 obj-$(CONFIG_CPU_EXYNOS4210)	+= clock-exynos4210.o
 obj-$(CONFIG_SOC_EXYNOS4212)	+= clock-exynos4212.o
 obj-$(CONFIG_PM)		+= pm.o
@@ -37,6 +37,8 @@ obj-$(CONFIG_MACH_ORIGEN)		+= mach-origen.o
 obj-$(CONFIG_MACH_SMDK4212)		+= mach-smdk4x12.o
 obj-$(CONFIG_MACH_SMDK4412)		+= mach-smdk4x12.o
 
+obj-$(CONFIG_MACH_EXYNOS4_DT)		+= mach-exynos4-dt.o
+
 # device support
 
 obj-$(CONFIG_ARCH_EXYNOS4)		+= dev-audio.o
@@ -44,6 +46,7 @@ obj-$(CONFIG_EXYNOS4_DEV_AHCI)		+= dev-ahci.o
 obj-$(CONFIG_EXYNOS4_DEV_PD)		+= dev-pd.o
 obj-$(CONFIG_EXYNOS4_DEV_SYSMMU)	+= dev-sysmmu.o
 obj-$(CONFIG_EXYNOS4_DEV_DWMCI)		+= dev-dwmci.o
+obj-$(CONFIG_EXYNOS4_DEV_DMA)		+= dma.o
 obj-$(CONFIG_EXYNOS4_DEV_USB_OHCI)	+= dev-ohci.o
 
 obj-$(CONFIG_EXYNOS4_SETUP_FIMC)	+= setup-fimc.o
@@ -56,6 +59,5 @@ obj-$(CONFIG_EXYNOS4_SETUP_I2C5)	+= setup-i2c5.o
 obj-$(CONFIG_EXYNOS4_SETUP_I2C6)	+= setup-i2c6.o
 obj-$(CONFIG_EXYNOS4_SETUP_I2C7)	+= setup-i2c7.o
 obj-$(CONFIG_EXYNOS4_SETUP_KEYPAD)	+= setup-keypad.o
-obj-$(CONFIG_EXYNOS4_SETUP_SDHCI)	+= setup-sdhci.o
 obj-$(CONFIG_EXYNOS4_SETUP_SDHCI_GPIO)	+= setup-sdhci-gpio.o
 obj-$(CONFIG_EXYNOS4_SETUP_USB_PHY)	+= setup-usb-phy.o

arch/arm/mach-exynos/clock.c

@@ -552,16 +552,6 @@ static struct clk init_clocks_off[] = {
 		.devname	= "s5p-sdo",
 		.enable		= exynos4_clk_dac_ctrl,
 		.ctrlbit	= (1 << 0),
-	}, {
-		.name		= "dma",
-		.devname	= "dma-pl330.0",
-		.enable		= exynos4_clk_ip_fsys_ctrl,
-		.ctrlbit	= (1 << 0),
-	}, {
-		.name		= "dma",
-		.devname	= "dma-pl330.1",
-		.enable		= exynos4_clk_ip_fsys_ctrl,
-		.ctrlbit	= (1 << 1),
 	}, {
 		.name		= "adc",
 		.enable		= exynos4_clk_ip_peril_ctrl,
@@ -778,6 +768,20 @@ static struct clk init_clocks[] = {
 	}
 };
 
+static struct clk clk_pdma0 = {
+	.name		= "dma",
+	.devname	= "dma-pl330.0",
+	.enable		= exynos4_clk_ip_fsys_ctrl,
+	.ctrlbit	= (1 << 0),
+};
+
+static struct clk clk_pdma1 = {
+	.name		= "dma",
+	.devname	= "dma-pl330.1",
+	.enable		= exynos4_clk_ip_fsys_ctrl,
+	.ctrlbit	= (1 << 1),
+};
+
 struct clk *clkset_group_list[] = {
 	[0] = &clk_ext_xtal_mux,
 	[1] = &clk_xusbxti,
@@ -1009,46 +1013,6 @@ static struct clksrc_clk clk_dout_mmc4 = {
 
 static struct clksrc_clk clksrcs[] = {
 	{
-		.clk	= {
-			.name		= "uclk1",
-			.devname	= "s5pv210-uart.0",
-			.enable		= exynos4_clksrc_mask_peril0_ctrl,
-			.ctrlbit	= (1 << 0),
-		},
-		.sources = &clkset_group,
-		.reg_src = { .reg = S5P_CLKSRC_PERIL0, .shift = 0, .size = 4 },
-		.reg_div = { .reg = S5P_CLKDIV_PERIL0, .shift = 0, .size = 4 },
-	}, {
-		.clk		= {
-			.name		= "uclk1",
-			.devname	= "s5pv210-uart.1",
-			.enable		= exynos4_clksrc_mask_peril0_ctrl,
-			.ctrlbit	= (1 << 4),
-		},
-		.sources = &clkset_group,
-		.reg_src = { .reg = S5P_CLKSRC_PERIL0, .shift = 4, .size = 4 },
-		.reg_div = { .reg = S5P_CLKDIV_PERIL0, .shift = 4, .size = 4 },
-	}, {
-		.clk		= {
-			.name		= "uclk1",
-			.devname	= "s5pv210-uart.2",
-			.enable		= exynos4_clksrc_mask_peril0_ctrl,
-			.ctrlbit	= (1 << 8),
-		},
-		.sources = &clkset_group,
-		.reg_src = { .reg = S5P_CLKSRC_PERIL0, .shift = 8, .size = 4 },
-		.reg_div = { .reg = S5P_CLKDIV_PERIL0, .shift = 8, .size = 4 },
-	}, {
-		.clk		= {
-			.name		= "uclk1",
-			.devname	= "s5pv210-uart.3",
-			.enable		= exynos4_clksrc_mask_peril0_ctrl,
-			.ctrlbit	= (1 << 12),
-		},
-		.sources = &clkset_group,
-		.reg_src = { .reg = S5P_CLKSRC_PERIL0, .shift = 12, .size = 4 },
-		.reg_div = { .reg = S5P_CLKDIV_PERIL0, .shift = 12, .size = 4 },
-	}, {
 		.clk		= {
 			.name		= "sclk_pwm",
 			.enable		= exynos4_clksrc_mask_peril0_ctrl,
@@ -1191,6 +1155,65 @@ static struct clksrc_clk clksrcs[] = {
 		.reg_src = { .reg = S5P_CLKSRC_MFC, .shift = 8, .size = 1 },
 		.reg_div = { .reg = S5P_CLKDIV_MFC, .shift = 0, .size = 4 },
 	}, {
+		.clk		= {
+			.name		= "sclk_dwmmc",
+			.parent         = &clk_dout_mmc4.clk,
+			.enable		= exynos4_clksrc_mask_fsys_ctrl,
+			.ctrlbit	= (1 << 16),
+		},
+		.reg_div = { .reg = S5P_CLKDIV_FSYS3, .shift = 8, .size = 8 },
+	}
+};
+
+static struct clksrc_clk clk_sclk_uart0 = {
+	.clk	= {
+		.name		= "uclk1",
+		.devname	= "exynos4210-uart.0",
+		.enable		= exynos4_clksrc_mask_peril0_ctrl,
+		.ctrlbit	= (1 << 0),
+	},
+	.sources = &clkset_group,
+	.reg_src = { .reg = S5P_CLKSRC_PERIL0, .shift = 0, .size = 4 },
+	.reg_div = { .reg = S5P_CLKDIV_PERIL0, .shift = 0, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_uart1 = {
+	.clk		= {
+		.name		= "uclk1",
+		.devname	= "exynos4210-uart.1",
+		.enable		= exynos4_clksrc_mask_peril0_ctrl,
+		.ctrlbit	= (1 << 4),
+	},
+	.sources = &clkset_group,
+	.reg_src = { .reg = S5P_CLKSRC_PERIL0, .shift = 4, .size = 4 },
+	.reg_div = { .reg = S5P_CLKDIV_PERIL0, .shift = 4, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_uart2 = {
+	.clk		= {
+		.name		= "uclk1",
+		.devname	= "exynos4210-uart.2",
+		.enable		= exynos4_clksrc_mask_peril0_ctrl,
+		.ctrlbit	= (1 << 8),
+	},
+	.sources = &clkset_group,
+	.reg_src = { .reg = S5P_CLKSRC_PERIL0, .shift = 8, .size = 4 },
+	.reg_div = { .reg = S5P_CLKDIV_PERIL0, .shift = 8, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_uart3 = {
+	.clk		= {
+		.name		= "uclk1",
+		.devname	= "exynos4210-uart.3",
+		.enable		= exynos4_clksrc_mask_peril0_ctrl,
+		.ctrlbit	= (1 << 12),
+	},
+	.sources = &clkset_group,
+	.reg_src = { .reg = S5P_CLKSRC_PERIL0, .shift = 12, .size = 4 },
+	.reg_div = { .reg = S5P_CLKDIV_PERIL0, .shift = 12, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_mmc0 = {
 	.clk		= {
 		.name		= "sclk_mmc",
 		.devname	= "s3c-sdhci.0",
@@ -1199,7 +1222,9 @@ static struct clksrc_clk clksrcs[] = {
 		.ctrlbit	= (1 << 0),
 	},
 	.reg_div = { .reg = S5P_CLKDIV_FSYS1, .shift = 8, .size = 8 },
-	}, {
+};
+
+static struct clksrc_clk clk_sclk_mmc1 = {
 	.clk		= {
 		.name		= "sclk_mmc",
 		.devname	= "s3c-sdhci.1",
@@ -1208,7 +1233,9 @@ static struct clksrc_clk clksrcs[] = {
 		.ctrlbit	= (1 << 4),
 	},
 	.reg_div = { .reg = S5P_CLKDIV_FSYS1, .shift = 24, .size = 8 },
-	}, {
+};
+
+static struct clksrc_clk clk_sclk_mmc2 = {
 	.clk		= {
 		.name		= "sclk_mmc",
 		.devname	= "s3c-sdhci.2",
@@ -1217,7 +1244,9 @@ static struct clksrc_clk clksrcs[] = {
 		.ctrlbit	= (1 << 8),
 	},
 	.reg_div = { .reg = S5P_CLKDIV_FSYS2, .shift = 8, .size = 8 },
-	}, {
+};
+
+static struct clksrc_clk clk_sclk_mmc3 = {
 	.clk		= {
 		.name		= "sclk_mmc",
 		.devname	= "s3c-sdhci.3",
@@ -1226,15 +1255,6 @@ static struct clksrc_clk clksrcs[] = {
 		.ctrlbit	= (1 << 12),
 	},
 	.reg_div = { .reg = S5P_CLKDIV_FSYS2, .shift = 24, .size = 8 },
-	}, {
-		.clk		= {
-			.name		= "sclk_dwmmc",
-			.parent         = &clk_dout_mmc4.clk,
-			.enable		= exynos4_clksrc_mask_fsys_ctrl,
-			.ctrlbit	= (1 << 16),
-		},
-		.reg_div = { .reg = S5P_CLKDIV_FSYS3, .shift = 8, .size = 8 },
-	}
 };
 
 /* Clock initialization code */
@@ -1271,6 +1291,35 @@ static struct clksrc_clk *sysclks[] = {
 	&clk_mout_mfc1,
 };
 
+static struct clk *clk_cdev[] = {
+	&clk_pdma0,
+	&clk_pdma1,
+};
+
+static struct clksrc_clk *clksrc_cdev[] = {
+	&clk_sclk_uart0,
+	&clk_sclk_uart1,
+	&clk_sclk_uart2,
+	&clk_sclk_uart3,
+	&clk_sclk_mmc0,
+	&clk_sclk_mmc1,
+	&clk_sclk_mmc2,
+	&clk_sclk_mmc3,
+};
+
+static struct clk_lookup exynos4_clk_lookup[] = {
+	CLKDEV_INIT("exynos4210-uart.0", "clk_uart_baud0", &clk_sclk_uart0.clk),
+	CLKDEV_INIT("exynos4210-uart.1", "clk_uart_baud0", &clk_sclk_uart1.clk),
+	CLKDEV_INIT("exynos4210-uart.2", "clk_uart_baud0", &clk_sclk_uart2.clk),
+	CLKDEV_INIT("exynos4210-uart.3", "clk_uart_baud0", &clk_sclk_uart3.clk),
+	CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.2", &clk_sclk_mmc0.clk),
+	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &clk_sclk_mmc1.clk),
+	CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.2", &clk_sclk_mmc2.clk),
+	CLKDEV_INIT("s3c-sdhci.3", "mmc_busclk.2", &clk_sclk_mmc3.clk),
+	CLKDEV_INIT("dma-pl330.0", "apb_pclk", &clk_pdma0),
+	CLKDEV_INIT("dma-pl330.1", "apb_pclk", &clk_pdma1),
+};
+
 static int xtal_rate;
 
 static unsigned long exynos4_fout_apll_get_rate(struct clk *clk)
@@ -1478,11 +1527,19 @@ void __init exynos4_register_clocks(void)
 	for (ptr = 0; ptr < ARRAY_SIZE(sclk_tv); ptr++)
 		s3c_register_clksrc(sclk_tv[ptr], 1);
 
+	for (ptr = 0; ptr < ARRAY_SIZE(clksrc_cdev); ptr++)
+		s3c_register_clksrc(clksrc_cdev[ptr], 1);
+
 	s3c_register_clksrc(clksrcs, ARRAY_SIZE(clksrcs));
 	s3c_register_clocks(init_clocks, ARRAY_SIZE(init_clocks));
 
+	s3c24xx_register_clocks(clk_cdev, ARRAY_SIZE(clk_cdev));
+	for (ptr = 0; ptr < ARRAY_SIZE(clk_cdev); ptr++)
+		s3c_disable_clocks(clk_cdev[ptr], 1);
+
 	s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
 	s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
+	clkdev_add_table(exynos4_clk_lookup, ARRAY_SIZE(exynos4_clk_lookup));
 
 	register_syscore_ops(&exynos4_clock_syscore_ops);
 	s3c24xx_register_clock(&dummy_apb_pclk);

arch/arm/mach-exynos/cpu.c

@@ -10,6 +10,8 @@
 
 #include <linux/sched.h>
 #include <linux/sysdev.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
 
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
@@ -218,13 +220,26 @@ static void exynos4_gic_irq_fix_base(struct irq_data *d)
 			    (gic_bank_offset * smp_processor_id());
 }
 
+#ifdef CONFIG_OF
+static const struct of_device_id exynos4_dt_irq_match[] = {
+	{ .compatible = "arm,cortex-a9-gic", .data = gic_of_init, },
+	{},
+};
+#endif
+
 void __init exynos4_init_irq(void)
 {
 	int irq;
 
 	gic_bank_offset = soc_is_exynos4412() ? 0x4000 : 0x8000;
 
+	if (!of_have_populated_dt())
 		gic_init(0, IRQ_PPI(0), S5P_VA_GIC_DIST, S5P_VA_GIC_CPU);
+#ifdef CONFIG_OF
+	else
+		of_irq_init(exynos4_dt_irq_match);
+#endif
+
 	gic_arch_extn.irq_eoi = exynos4_gic_irq_fix_base;
 	gic_arch_extn.irq_unmask = exynos4_gic_irq_fix_base;
 	gic_arch_extn.irq_mask = exynos4_gic_irq_fix_base;

arch/arm/mach-exynos/dma.c

@@ -24,6 +24,7 @@
 #include <linux/dma-mapping.h>
 #include <linux/amba/bus.h>
 #include <linux/amba/pl330.h>
+#include <linux/of.h>
 
 #include <asm/irq.h>
 #include <plat/devs.h>
@@ -35,95 +36,42 @@
 
 static u64 dma_dmamask = DMA_BIT_MASK(32);
 
-struct dma_pl330_peri pdma0_peri[28] = {
-	{
-		.peri_id = (u8)DMACH_PCM0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_PCM0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_PCM2_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_PCM2_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_MSM_REQ0,
-	}, {
-		.peri_id = (u8)DMACH_MSM_REQ2,
-	}, {
-		.peri_id = (u8)DMACH_SPI0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_SPI0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_SPI2_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_SPI2_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_I2S0S_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_I2S0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_I2S0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_UART0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_UART2_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART2_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_UART4_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART4_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_SLIMBUS0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_SLIMBUS0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_SLIMBUS2_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_SLIMBUS2_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_SLIMBUS4_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_SLIMBUS4_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_AC97_MICIN,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_AC97_PCMIN,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_AC97_PCMOUT,
-		.rqtype = MEMTODEV,
-	},
+u8 pdma0_peri[] = {
+	DMACH_PCM0_RX,
+	DMACH_PCM0_TX,
+	DMACH_PCM2_RX,
+	DMACH_PCM2_TX,
+	DMACH_MSM_REQ0,
+	DMACH_MSM_REQ2,
+	DMACH_SPI0_RX,
+	DMACH_SPI0_TX,
+	DMACH_SPI2_RX,
+	DMACH_SPI2_TX,
+	DMACH_I2S0S_TX,
+	DMACH_I2S0_RX,
+	DMACH_I2S0_TX,
+	DMACH_I2S2_RX,
+	DMACH_I2S2_TX,
+	DMACH_UART0_RX,
+	DMACH_UART0_TX,
+	DMACH_UART2_RX,
+	DMACH_UART2_TX,
+	DMACH_UART4_RX,
+	DMACH_UART4_TX,
+	DMACH_SLIMBUS0_RX,
+	DMACH_SLIMBUS0_TX,
+	DMACH_SLIMBUS2_RX,
+	DMACH_SLIMBUS2_TX,
+	DMACH_SLIMBUS4_RX,
+	DMACH_SLIMBUS4_TX,
+	DMACH_AC97_MICIN,
+	DMACH_AC97_PCMIN,
+	DMACH_AC97_PCMOUT,
 };
 
 struct dma_pl330_platdata exynos4_pdma0_pdata = {
 	.nr_valid_peri = ARRAY_SIZE(pdma0_peri),
-	.peri = pdma0_peri,
+	.peri_id = pdma0_peri,
 };
 
 struct amba_device exynos4_device_pdma0 = {
@@ -142,86 +90,37 @@ struct amba_device exynos4_device_pdma0 = {
 	.periphid = 0x00041330,
 };
 
-struct dma_pl330_peri pdma1_peri[25] = {
-	{
-		.peri_id = (u8)DMACH_PCM0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_PCM0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_PCM1_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_PCM1_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_MSM_REQ1,
-	}, {
-		.peri_id = (u8)DMACH_MSM_REQ3,
-	}, {
-		.peri_id = (u8)DMACH_SPI1_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_SPI1_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_I2S0S_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_I2S0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_I2S0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_I2S1_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_I2S1_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_UART0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_UART1_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART1_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_UART3_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART3_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_SLIMBUS1_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_SLIMBUS1_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_SLIMBUS3_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_SLIMBUS3_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_SLIMBUS5_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_SLIMBUS5_TX,
-		.rqtype = MEMTODEV,
-	},
+u8 pdma1_peri[] = {
+	DMACH_PCM0_RX,
+	DMACH_PCM0_TX,
+	DMACH_PCM1_RX,
+	DMACH_PCM1_TX,
+	DMACH_MSM_REQ1,
+	DMACH_MSM_REQ3,
+	DMACH_SPI1_RX,
+	DMACH_SPI1_TX,
+	DMACH_I2S0S_TX,
+	DMACH_I2S0_RX,
+	DMACH_I2S0_TX,
+	DMACH_I2S1_RX,
+	DMACH_I2S1_TX,
+	DMACH_UART0_RX,
+	DMACH_UART0_TX,
+	DMACH_UART1_RX,
+	DMACH_UART1_TX,
+	DMACH_UART3_RX,
+	DMACH_UART3_TX,
+	DMACH_SLIMBUS1_RX,
+	DMACH_SLIMBUS1_TX,
+	DMACH_SLIMBUS3_RX,
+	DMACH_SLIMBUS3_TX,
+	DMACH_SLIMBUS5_RX,
+	DMACH_SLIMBUS5_TX,
 };
 
 struct dma_pl330_platdata exynos4_pdma1_pdata = {
 	.nr_valid_peri = ARRAY_SIZE(pdma1_peri),
-	.peri = pdma1_peri,
+	.peri_id = pdma1_peri,
 };
 
 struct amba_device exynos4_device_pdma1 = {
@@ -242,7 +141,15 @@ struct amba_device exynos4_device_pdma1 = {
 
 static int __init exynos4_dma_init(void)
 {
+	if (of_have_populated_dt())
+		return 0;
+
+	dma_cap_set(DMA_SLAVE, exynos4_pdma0_pdata.cap_mask);
+	dma_cap_set(DMA_CYCLIC, exynos4_pdma0_pdata.cap_mask);
 	amba_device_register(&exynos4_device_pdma0, &iomem_resource);
+
+	dma_cap_set(DMA_SLAVE, exynos4_pdma1_pdata.cap_mask);
+	dma_cap_set(DMA_CYCLIC, exynos4_pdma1_pdata.cap_mask);
 	amba_device_register(&exynos4_device_pdma1, &iomem_resource);
 
 	return 0;

arch/arm/mach-exynos/include/mach/entry-macro.S

@@ -72,7 +72,6 @@
 		cmpcc	\irqnr, \irqnr
 		cmpne	\irqnr, \tmp
 		cmpcs	\irqnr, \irqnr
-		addne	\irqnr, \irqnr, #32
 
 		.endm
 

arch/arm/mach-exynos/include/mach/irqs.h

@@ -17,13 +17,13 @@
 
 /* PPI: Private Peripheral Interrupt */
 
-#define IRQ_PPI(x)		S5P_IRQ(x+16)
+#define IRQ_PPI(x)		(x+16)
 
 #define IRQ_MCT_LOCALTIMER	IRQ_PPI(12)
 
 /* SPI: Shared Peripheral Interrupt */
 
-#define IRQ_SPI(x)		S5P_IRQ(x+32)
+#define IRQ_SPI(x)		(x+32)
 
 #define IRQ_EINT0		IRQ_SPI(16)
 #define IRQ_EINT1		IRQ_SPI(17)
@@ -163,7 +163,9 @@
 #define IRQ_GPIO2_NR_GROUPS	9
 #define IRQ_GPIO_END		(S5P_GPIOINT_BASE + S5P_GPIOINT_COUNT)
 
+#define IRQ_TIMER_BASE		(IRQ_GPIO_END + 64)
+
 /* Set the default NR_IRQS */
-#define NR_IRQS			(IRQ_GPIO_END + 64)
+#define NR_IRQS			(IRQ_TIMER_BASE + IRQ_TIMER_COUNT)
 
 #endif /* __ASM_ARCH_IRQS_H */

arch/arm/mach-exynos/init.c

@@ -14,29 +14,14 @@
 #include <plat/devs.h>
 #include <plat/regs-serial.h>
 
-static struct s3c24xx_uart_clksrc exynos4_serial_clocks[] = {
-	[0] = {
-		.name		= "uclk1",
-		.divisor	= 1,
-		.min_baud	= 0,
-		.max_baud	= 0,
-	},
-};
-
 /* uart registration process */
 void __init exynos4_common_init_uarts(struct s3c2410_uartcfg *cfg, int no)
 {
 	struct s3c2410_uartcfg *tcfg = cfg;
 	u32 ucnt;
 
-	for (ucnt = 0; ucnt < no; ucnt++, tcfg++) {
-		if (!tcfg->clocks) {
+	for (ucnt = 0; ucnt < no; ucnt++, tcfg++)
 		tcfg->has_fracval = 1;
-			tcfg->clocks = exynos4_serial_clocks;
-			tcfg->clocks_size = ARRAY_SIZE(exynos4_serial_clocks);
-		}
-		tcfg->flags |= NO_NEED_CHECK_CLKSRC;
-	}
 
-	s3c24xx_init_uartdevs("s5pv210-uart", s5p_uart_resources, cfg, no);
+	s3c24xx_init_uartdevs("exynos4210-uart", s5p_uart_resources, cfg, no);
 }

arch/arm/mach-exynos/mach-exynos4-dt.c

+/*
+ * Samsung's Exynos4210 flattened device tree enabled machine
+ *
+ * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2010-2011 Linaro Ltd.
+ *		www.linaro.org
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/of_platform.h>
+#include <linux/serial_core.h>
+
+#include <asm/mach/arch.h>
+#include <mach/map.h>
+
+#include <plat/cpu.h>
+#include <plat/regs-serial.h>
+#include <plat/exynos4.h>
+
+/*
+ * The following lookup table is used to override device names when devices
+ * are registered from device tree. This is temporarily added to enable
+ * device tree support addition for the Exynos4 architecture.
+ *
+ * For drivers that require platform data to be provided from the machine
+ * file, a platform data pointer can also be supplied along with the
+ * devices names. Usually, the platform data elements that cannot be parsed
+ * from the device tree by the drivers (example: function pointers) are
+ * supplied. But it should be noted that this is a temporary mechanism and
+ * at some point, the drivers should be capable of parsing all the platform
+ * data from the device tree.
+ */
+static const struct of_dev_auxdata exynos4210_auxdata_lookup[] __initconst = {
+	OF_DEV_AUXDATA("samsung,exynos4210-uart", S5P_PA_UART0,
+				"exynos4210-uart.0", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-uart", S5P_PA_UART1,
+				"exynos4210-uart.1", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-uart", S5P_PA_UART2,
+				"exynos4210-uart.2", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-uart", S5P_PA_UART3,
+				"exynos4210-uart.3", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-sdhci", EXYNOS4_PA_HSMMC(0),
+				"exynos4-sdhci.0", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-sdhci", EXYNOS4_PA_HSMMC(1),
+				"exynos4-sdhci.1", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-sdhci", EXYNOS4_PA_HSMMC(2),
+				"exynos4-sdhci.2", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-sdhci", EXYNOS4_PA_HSMMC(3),
+				"exynos4-sdhci.3", NULL),
+	OF_DEV_AUXDATA("samsung,s3c2440-i2c", EXYNOS4_PA_IIC(0),
+				"s3c2440-i2c.0", NULL),
+	OF_DEV_AUXDATA("arm,pl330", EXYNOS4_PA_PDMA0, "dma-pl330.0", NULL),
+	OF_DEV_AUXDATA("arm,pl330", EXYNOS4_PA_PDMA1, "dma-pl330.1", NULL),
+	{},
+};
+
+static void __init exynos4210_dt_map_io(void)
+{
+	s5p_init_io(NULL, 0, S5P_VA_CHIPID);
+	s3c24xx_init_clocks(24000000);
+}
+
+static void __init exynos4210_dt_machine_init(void)
+{
+	of_platform_populate(NULL, of_default_bus_match_table,
+				exynos4210_auxdata_lookup, NULL);
+}
+
+static char const *exynos4210_dt_compat[] __initdata = {
+	"samsung,exynos4210",
+	NULL
+};
+
+DT_MACHINE_START(EXYNOS4210_DT, "Samsung Exynos4 (Flattened Device Tree)")
+	/* Maintainer: Thomas Abraham <thomas.abraham@linaro.org> */
+	.init_irq	= exynos4_init_irq,
+	.map_io		= exynos4210_dt_map_io,
+	.init_machine	= exynos4210_dt_machine_init,
+	.timer		= &exynos4_timer,
+	.dt_compat	= exynos4210_dt_compat,
+MACHINE_END

arch/arm/mach-exynos/setup-sdhci.c

-/* linux/arch/arm/mach-exynos4/setup-sdhci.c
- *
- * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com
- *
- * EXYNOS4 - Helper functions for settign up SDHCI device(s) (HSMMC)
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/types.h>
-
-/* clock sources for the mmc bus clock, order as for the ctrl2[5..4] */
-
-char *exynos4_hsmmc_clksrcs[4] = {
-	[0] = NULL,
-	[1] = NULL,
-	[2] = "sclk_mmc",	/* mmc_bus */
-	[3] = NULL,
-};

arch/arm/mach-s3c2410/mach-bast.c

@@ -164,22 +164,6 @@ static struct map_desc bast_iodesc[] __initdata = {
 #define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
 #define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
 
-static struct s3c24xx_uart_clksrc bast_serial_clocks[] = {
-	[0] = {
-		.name		= "uclk",
-		.divisor	= 1,
-		.min_baud	= 0,
-		.max_baud	= 0,
-	},
-	[1] = {
-		.name		= "pclk",
-		.divisor	= 1,
-		.min_baud	= 0,
-		.max_baud	= 0,
-	}
-};
-
-
 static struct s3c2410_uartcfg bast_uartcfgs[] __initdata = {
 	[0] = {
 		.hwport	     = 0,
@@ -187,8 +171,6 @@ static struct s3c2410_uartcfg bast_uartcfgs[] __initdata = {
 		.ucon	     = UCON,
 		.ulcon	     = ULCON,
 		.ufcon	     = UFCON,
-		.clocks	     = bast_serial_clocks,
-		.clocks_size = ARRAY_SIZE(bast_serial_clocks),
 	},
 	[1] = {
 		.hwport	     = 1,
@@ -196,8 +178,6 @@ static struct s3c2410_uartcfg bast_uartcfgs[] __initdata = {
 		.ucon	     = UCON,
 		.ulcon	     = ULCON,
 		.ufcon	     = UFCON,
-		.clocks	     = bast_serial_clocks,
-		.clocks_size = ARRAY_SIZE(bast_serial_clocks),
 	},
 	/* port 2 is not actually used */
 	[2] = {
@@ -206,8 +186,6 @@ static struct s3c2410_uartcfg bast_uartcfgs[] __initdata = {
 		.ucon	     = UCON,
 		.ulcon	     = ULCON,
 		.ufcon	     = UFCON,
-		.clocks	     = bast_serial_clocks,
-		.clocks_size = ARRAY_SIZE(bast_serial_clocks),
 	}
 };
 

arch/arm/mach-s3c2410/mach-vr1000.c

@@ -109,23 +109,6 @@ static struct map_desc vr1000_iodesc[] __initdata = {
 #define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
 #define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
 
-/* uart clock source(s) */
-
-static struct s3c24xx_uart_clksrc vr1000_serial_clocks[] = {
-	[0] = {
-		.name		= "uclk",
-		.divisor	= 1,
-		.min_baud	= 0,
-		.max_baud	= 0,
-	},
-	[1] = {
-		.name		= "pclk",
-		.divisor	= 1,
-		.min_baud	= 0,
-		.max_baud	= 0.
-	}
-};
-
 static struct s3c2410_uartcfg vr1000_uartcfgs[] __initdata = {
 	[0] = {
 		.hwport	     = 0,
@@ -133,8 +116,6 @@ static struct s3c2410_uartcfg vr1000_uartcfgs[] __initdata = {
 		.ucon	     = UCON,
 		.ulcon	     = ULCON,
 		.ufcon	     = UFCON,
-		.clocks	     = vr1000_serial_clocks,
-		.clocks_size = ARRAY_SIZE(vr1000_serial_clocks),
 	},
 	[1] = {
 		.hwport	     = 1,
@@ -142,8 +123,6 @@ static struct s3c2410_uartcfg vr1000_uartcfgs[] __initdata = {
 		.ucon	     = UCON,
 		.ulcon	     = ULCON,
 		.ufcon	     = UFCON,
-		.clocks	     = vr1000_serial_clocks,
-		.clocks_size = ARRAY_SIZE(vr1000_serial_clocks),
 	},
 	/* port 2 is not actually used */
 	[2] = {
@@ -152,9 +131,6 @@ static struct s3c2410_uartcfg vr1000_uartcfgs[] __initdata = {
 		.ucon	     = UCON,
 		.ulcon	     = ULCON,
 		.ufcon	     = UFCON,
-		.clocks	     = vr1000_serial_clocks,
-		.clocks_size = ARRAY_SIZE(vr1000_serial_clocks),
-
 	}
 };
 

arch/arm/mach-s3c2410/s3c2410.c

@@ -123,12 +123,18 @@ static struct clk s3c2410_armclk = {
 	.id	= -1,
 };
 
+static struct clk_lookup s3c2410_clk_lookup[] = {
+	CLKDEV_INIT(NULL, "clk_uart_baud0", &clk_p),
+	CLKDEV_INIT(NULL, "clk_uart_baud1", &s3c24xx_uclk),
+};
+
 void __init s3c2410_init_clocks(int xtal)
 {
 	s3c24xx_register_baseclocks(xtal);
 	s3c2410_setup_clocks();
 	s3c2410_baseclk_add();
 	s3c24xx_register_clock(&s3c2410_armclk);
+	clkdev_add_table(s3c2410_clk_lookup, ARRAY_SIZE(s3c2410_clk_lookup));
 }
 
 struct sysdev_class s3c2410_sysclass = {

arch/arm/mach-s3c2412/clock.c

@@ -659,6 +659,12 @@ static struct clk *clks[] __initdata = {
 	&clk_armclk,
 };
 
+static struct clk_lookup s3c2412_clk_lookup[] = {
+	CLKDEV_INIT(NULL, "clk_uart_baud1", &s3c24xx_uclk),
+	CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_p),
+	CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_usysclk),
+};
+
 int __init s3c2412_baseclk_add(void)
 {
 	unsigned long clkcon  = __raw_readl(S3C2410_CLKCON);
@@ -751,6 +757,7 @@ int __init s3c2412_baseclk_add(void)
 		s3c2412_clkcon_enable(clkp, 0);
 	}
 
+	clkdev_add_table(s3c2412_clk_lookup, ARRAY_SIZE(s3c2412_clk_lookup));
 	s3c_pwmclk_init();
 	return 0;
 }

arch/arm/mach-s3c2416/Makefile

@@ -15,7 +15,6 @@ obj-$(CONFIG_S3C2416_PM)	+= pm.o
 #obj-$(CONFIG_S3C2416_DMA)	+= dma.o
 
 # Device setup
-obj-$(CONFIG_S3C2416_SETUP_SDHCI) += setup-sdhci.o
 obj-$(CONFIG_S3C2416_SETUP_SDHCI_GPIO) += setup-sdhci-gpio.o
 
 # Machine support

arch/arm/mach-s3c2416/clock.c

@@ -90,8 +90,7 @@ static struct clksrc_clk hsmmc_div[] = {
 	},
 };
 
-static struct clksrc_clk hsmmc_mux[] = {
-	[0] = {
+static struct clksrc_clk hsmmc_mux0 = {
 	.clk	= {
 		.name		= "hsmmc-if",
 		.devname	= "s3c-sdhci.0",
@@ -100,14 +99,15 @@ static struct clksrc_clk hsmmc_mux[] = {
 	},
 	.sources	= &(struct clksrc_sources) {
 		.nr_sources	= 2,
-			.sources = (struct clk *[]) {
+		.sources	= (struct clk * []) {
 			[0]	= &hsmmc_div[0].clk,
 			[1]	= NULL, /* to fix */
 		},
 	},
 	.reg_src = { .reg = S3C2443_CLKSRC, .size = 1, .shift = 16 },
-	},
-	[1] = {
+};
+
+static struct clksrc_clk hsmmc_mux1 = {
 	.clk	= {
 		.name		= "hsmmc-if",
 		.devname	= "s3c-sdhci.1",
@@ -116,13 +116,12 @@ static struct clksrc_clk hsmmc_mux[] = {
 	},
 	.sources	= &(struct clksrc_sources) {
 		.nr_sources	= 2,
-			.sources = (struct clk *[]) {
+		.sources	= (struct clk * []) {
 			[0]	= &hsmmc_div[1].clk,
 			[1]	= NULL, /* to fix */
 		},
 	},
 	.reg_src = { .reg = S3C2443_CLKSRC, .size = 1, .shift = 17 },
-	},
 };
 
 static struct clk hsmmc0_clk = {
@@ -144,8 +143,14 @@ static struct clksrc_clk *clksrcs[] __initdata = {
 	&hsspi_mux,
 	&hsmmc_div[0],
 	&hsmmc_div[1],
-	&hsmmc_mux[0],
-	&hsmmc_mux[1],
+	&hsmmc_mux0,
+	&hsmmc_mux1,
+};
+
+static struct clk_lookup s3c2416_clk_lookup[] = {
+	CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.0", &hsmmc0_clk),
+	CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.2", &hsmmc_mux0.clk),
+	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &hsmmc_mux1.clk),
 };
 
 void __init s3c2416_init_clocks(int xtal)
@@ -167,6 +172,7 @@ void __init s3c2416_init_clocks(int xtal)
 		s3c_register_clksrc(clksrcs[ptr], 1);
 
 	s3c24xx_register_clock(&hsmmc0_clk);
+	clkdev_add_table(s3c2416_clk_lookup, ARRAY_SIZE(s3c2416_clk_lookup));
 
 	s3c_pwmclk_init();
 

arch/arm/mach-s3c2416/setup-sdhci.c

-/* linux/arch/arm/mach-s3c2416/setup-sdhci.c
- *
- * Copyright 2010 Promwad Innovation Company
- *	Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
- *
- * S3C2416 - Helper functions for settign up SDHCI device(s) (HSMMC)
- *
- * Based on mach-s3c64xx/setup-sdhci.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/types.h>
-
-/* clock sources for the mmc bus clock, order as for the ctrl2[5..4] */
-
-char *s3c2416_hsmmc_clksrcs[4] = {
-	[0] = "hsmmc",
-	[1] = "hsmmc",
-	[2] = "hsmmc-if",
-	/* [3] = "48m", - note not successfully used yet */
-};

arch/arm/mach-s3c2440/clock.c

@@ -34,6 +34,7 @@
 #include <linux/mutex.h>
 #include <linux/clk.h>
 #include <linux/io.h>
+#include <linux/serial_core.h>
 
 #include <mach/hardware.h>
 #include <linux/atomic.h>
@@ -43,6 +44,7 @@
 
 #include <plat/clock.h>
 #include <plat/cpu.h>
+#include <plat/regs-serial.h>
 
 /* S3C2440 extended clock support */
 
@@ -108,6 +110,46 @@ static struct clk s3c2440_clk_ac97 = {
 	.ctrlbit	= S3C2440_CLKCON_CAMERA,
 };
 
+static unsigned long  s3c2440_fclk_n_getrate(struct clk *clk)
+{
+	unsigned long ucon0, ucon1, ucon2, divisor;
+
+	/* the fun of calculating the uart divisors on the s3c2440 */
+	ucon0 = __raw_readl(S3C24XX_VA_UART0 + S3C2410_UCON);
+	ucon1 = __raw_readl(S3C24XX_VA_UART1 + S3C2410_UCON);
+	ucon2 = __raw_readl(S3C24XX_VA_UART2 + S3C2410_UCON);
+
+	ucon0 &= S3C2440_UCON0_DIVMASK;
+	ucon1 &= S3C2440_UCON1_DIVMASK;
+	ucon2 &= S3C2440_UCON2_DIVMASK;
+
+	if (ucon0 != 0)
+		divisor = (ucon0 >> S3C2440_UCON_DIVSHIFT) + 6;
+	else if (ucon1 != 0)
+		divisor = (ucon1 >> S3C2440_UCON_DIVSHIFT) + 21;
+	else if (ucon2 != 0)
+		divisor = (ucon2 >> S3C2440_UCON_DIVSHIFT) + 36;
+	else
+		/* manual calims 44, seems to be 9 */
+		divisor = 9;
+
+	return clk_get_rate(clk->parent) / divisor;
+}
+
+static struct clk s3c2440_clk_fclk_n = {
+	.name		= "fclk_n",
+	.parent		= &clk_f,
+	.ops		= &(struct clk_ops) {
+		.get_rate	= s3c2440_fclk_n_getrate,
+	},
+};
+
+static struct clk_lookup s3c2440_clk_lookup[] = {
+	CLKDEV_INIT(NULL, "clk_uart_baud1", &s3c24xx_uclk),
+	CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_p),
+	CLKDEV_INIT(NULL, "clk_uart_baud3", &s3c2440_clk_fclk_n),
+};
+
 static int s3c2440_clk_add(struct sys_device *sysdev)
 {
 	struct clk *clock_upll;
@@ -126,10 +168,12 @@ static int s3c2440_clk_add(struct sys_device *sysdev)
 	s3c2440_clk_cam.parent = clock_h;
 	s3c2440_clk_ac97.parent = clock_p;
 	s3c2440_clk_cam_upll.parent = clock_upll;
+	s3c24xx_register_clock(&s3c2440_clk_fclk_n);
 
 	s3c24xx_register_clock(&s3c2440_clk_ac97);
 	s3c24xx_register_clock(&s3c2440_clk_cam);
 	s3c24xx_register_clock(&s3c2440_clk_cam_upll);
+	clkdev_add_table(s3c2440_clk_lookup, ARRAY_SIZE(s3c2440_clk_lookup));
 
 	clk_disable(&s3c2440_clk_ac97);
 	clk_disable(&s3c2440_clk_cam);

arch/arm/mach-s3c2440/mach-anubis.c

@@ -96,22 +96,6 @@ static struct map_desc anubis_iodesc[] __initdata = {
 #define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
 #define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
 
-static struct s3c24xx_uart_clksrc anubis_serial_clocks[] = {
-	[0] = {
-		.name		= "uclk",
-		.divisor	= 1,
-		.min_baud	= 0,
-		.max_baud	= 0,
-	},
-	[1] = {
-		.name		= "pclk",
-		.divisor	= 1,
-		.min_baud	= 0,
-		.max_baud	= 0,
-	}
-};
-
-
 static struct s3c2410_uartcfg anubis_uartcfgs[] __initdata = {
 	[0] = {
 		.hwport	     = 0,
@@ -119,8 +103,7 @@ static struct s3c2410_uartcfg anubis_uartcfgs[] __initdata = {
 		.ucon	     = UCON,
 		.ulcon	     = ULCON,
 		.ufcon	     = UFCON,
-		.clocks	     = anubis_serial_clocks,
-		.clocks_size = ARRAY_SIZE(anubis_serial_clocks),
+		.clk_sel	= S3C2410_UCON_CLKSEL1 | S3C2410_UCON_CLKSEL2,
 	},
 	[1] = {
 		.hwport	     = 2,
@@ -128,8 +111,7 @@ static struct s3c2410_uartcfg anubis_uartcfgs[] __initdata = {
 		.ucon	     = UCON,
 		.ulcon	     = ULCON,
 		.ufcon	     = UFCON,
-		.clocks	     = anubis_serial_clocks,
-		.clocks_size = ARRAY_SIZE(anubis_serial_clocks),
+		.clk_sel	= S3C2410_UCON_CLKSEL1 | S3C2410_UCON_CLKSEL2,
 	},
 };
 

arch/arm/mach-s3c2440/mach-at2440evb.c

@@ -57,22 +57,6 @@ static struct map_desc at2440evb_iodesc[] __initdata = {
 #define ULCON (S3C2410_LCON_CS8 | S3C2410_LCON_PNONE)
 #define UFCON (S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE)
 
-static struct s3c24xx_uart_clksrc at2440evb_serial_clocks[] = {
-	[0] = {
-		.name		= "uclk",
-		.divisor	= 1,
-		.min_baud	= 0,
-		.max_baud	= 0,
-	},
-	[1] = {
-		.name		= "pclk",
-		.divisor	= 1,
-		.min_baud	= 0,
-		.max_baud	= 0,
-	}
-};
-
-
 static struct s3c2410_uartcfg at2440evb_uartcfgs[] __initdata = {
 	[0] = {
 		.hwport	     = 0,
@@ -80,8 +64,7 @@ static struct s3c2410_uartcfg at2440evb_uartcfgs[] __initdata = {
 		.ucon	     = UCON,
 		.ulcon	     = ULCON,
 		.ufcon	     = UFCON,
-		.clocks	     = at2440evb_serial_clocks,
-		.clocks_size = ARRAY_SIZE(at2440evb_serial_clocks),
+		.clk_sel	= S3C2410_UCON_CLKSEL1 | S3C2410_UCON_CLKSEL2,
 	},
 	[1] = {
 		.hwport	     = 1,
@@ -89,8 +72,7 @@ static struct s3c2410_uartcfg at2440evb_uartcfgs[] __initdata = {
 		.ucon	     = UCON,
 		.ulcon	     = ULCON,
 		.ufcon	     = UFCON,
-		.clocks	     = at2440evb_serial_clocks,
-		.clocks_size = ARRAY_SIZE(at2440evb_serial_clocks),
+		.clk_sel	= S3C2410_UCON_CLKSEL1 | S3C2410_UCON_CLKSEL2,
 	},
 };
 

arch/arm/mach-s3c2440/mach-osiris.c

@@ -100,21 +100,6 @@ static struct map_desc osiris_iodesc[] __initdata = {
 #define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
 #define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
 
-static struct s3c24xx_uart_clksrc osiris_serial_clocks[] = {
-	[0] = {
-		.name		= "uclk",
-		.divisor	= 1,
-		.min_baud	= 0,
-		.max_baud	= 0,
-	},
-	[1] = {
-		.name		= "pclk",
-		.divisor	= 1,
-		.min_baud	= 0,
-		.max_baud	= 0,
-	}
-};
-
 static struct s3c2410_uartcfg osiris_uartcfgs[] __initdata = {
 	[0] = {
 		.hwport	     = 0,
@@ -122,8 +107,7 @@ static struct s3c2410_uartcfg osiris_uartcfgs[] __initdata = {
 		.ucon	     = UCON,
 		.ulcon	     = ULCON,
 		.ufcon	     = UFCON,
-		.clocks	     = osiris_serial_clocks,
-		.clocks_size = ARRAY_SIZE(osiris_serial_clocks),
+		.clk_sel	= S3C2410_UCON_CLKSEL1 | S3C2410_UCON_CLKSEL2,
 	},
 	[1] = {
 		.hwport	     = 1,
@@ -131,8 +115,7 @@ static struct s3c2410_uartcfg osiris_uartcfgs[] __initdata = {
 		.ucon	     = UCON,
 		.ulcon	     = ULCON,
 		.ufcon	     = UFCON,
-		.clocks	     = osiris_serial_clocks,
-		.clocks_size = ARRAY_SIZE(osiris_serial_clocks),
+		.clk_sel	= S3C2410_UCON_CLKSEL1 | S3C2410_UCON_CLKSEL2,
 	},
 	[2] = {
 		.hwport	     = 2,
@@ -140,8 +123,7 @@ static struct s3c2410_uartcfg osiris_uartcfgs[] __initdata = {
 		.ucon	     = UCON,
 		.ulcon	     = ULCON,
 		.ufcon	     = UFCON,
-		.clocks	     = osiris_serial_clocks,
-		.clocks_size = ARRAY_SIZE(osiris_serial_clocks),
+		.clk_sel	= S3C2410_UCON_CLKSEL1 | S3C2410_UCON_CLKSEL2,
 	}
 };
 

arch/arm/mach-s3c2440/mach-rx1950.c

@@ -68,15 +68,6 @@
 static struct map_desc rx1950_iodesc[] __initdata = {
 };
 
-static struct s3c24xx_uart_clksrc rx1950_serial_clocks[] = {
-	[0] = {
-	       .name = "fclk",
-	       .divisor = 0x0a,
-	       .min_baud = 0,
-	       .max_baud = 0,
-	},
-};
-
 static struct s3c2410_uartcfg rx1950_uartcfgs[] __initdata = {
 	[0] = {
 	       .hwport = 0,
@@ -84,8 +75,7 @@ static struct s3c2410_uartcfg rx1950_uartcfgs[] __initdata = {
 	       .ucon = 0x3c5,
 	       .ulcon = 0x03,
 	       .ufcon = 0x51,
-	       .clocks = rx1950_serial_clocks,
-	       .clocks_size = ARRAY_SIZE(rx1950_serial_clocks),
+		.clk_sel = S3C2410_UCON_CLKSEL3,
 	},
 	[1] = {
 	       .hwport = 1,
@@ -93,8 +83,7 @@ static struct s3c2410_uartcfg rx1950_uartcfgs[] __initdata = {
 	       .ucon = 0x3c5,
 	       .ulcon = 0x03,
 	       .ufcon = 0x51,
-	       .clocks = rx1950_serial_clocks,
-	       .clocks_size = ARRAY_SIZE(rx1950_serial_clocks),
+		.clk_sel = S3C2410_UCON_CLKSEL3,
 	},
 	/* IR port */
 	[2] = {
@@ -103,8 +92,7 @@ static struct s3c2410_uartcfg rx1950_uartcfgs[] __initdata = {
 	       .ucon = 0x3c5,
 	       .ulcon = 0x43,
 	       .ufcon = 0xf1,
-	       .clocks = rx1950_serial_clocks,
-	       .clocks_size = ARRAY_SIZE(rx1950_serial_clocks),
+		.clk_sel = S3C2410_UCON_CLKSEL3,
 	},
 };
 

arch/arm/mach-s3c2440/mach-rx3715.c

@@ -67,16 +67,6 @@ static struct map_desc rx3715_iodesc[] __initdata = {
 	},
 };
 
-
-static struct s3c24xx_uart_clksrc rx3715_serial_clocks[] = {
-	[0] = {
-		.name		= "fclk",
-		.divisor	= 0,
-		.min_baud	= 0,
-		.max_baud	= 0,
-	}
-};
-
 static struct s3c2410_uartcfg rx3715_uartcfgs[] = {
 	[0] = {
 		.hwport	     = 0,
@@ -84,8 +74,7 @@ static struct s3c2410_uartcfg rx3715_uartcfgs[] = {
 		.ucon	     = 0x3c5,
 		.ulcon	     = 0x03,
 		.ufcon	     = 0x51,
-		.clocks	     = rx3715_serial_clocks,
-		.clocks_size = ARRAY_SIZE(rx3715_serial_clocks),
+		.clk_sel	= S3C2410_UCON_CLKSEL3,
 	},
 	[1] = {
 		.hwport	     = 1,
@@ -93,8 +82,7 @@ static struct s3c2410_uartcfg rx3715_uartcfgs[] = {
 		.ucon	     = 0x3c5,
 		.ulcon	     = 0x03,
 		.ufcon	     = 0x00,
-		.clocks	     = rx3715_serial_clocks,
-		.clocks_size = ARRAY_SIZE(rx3715_serial_clocks),
+		.clk_sel	= S3C2410_UCON_CLKSEL3,
 	},
 	/* IR port */
 	[2] = {
@@ -103,8 +91,7 @@ static struct s3c2410_uartcfg rx3715_uartcfgs[] = {
 		.ucon	     = 0x3c5,
 		.ulcon	     = 0x43,
 		.ufcon	     = 0x51,
-		.clocks	     = rx3715_serial_clocks,
-		.clocks_size = ARRAY_SIZE(rx3715_serial_clocks),
+		.clk_sel	= S3C2410_UCON_CLKSEL3,
 	}
 };
 

arch/arm/mach-s3c64xx/Kconfig

@@ -77,6 +77,11 @@ config S3C64XX_SETUP_SDHCI_GPIO
 	help
 	  Common setup code for S3C64XX SDHCI GPIO configurations
 
+config S3C64XX_SETUP_SPI
+	bool
+	help
+	 Common setup code for SPI GPIO configurations
+
 # S36400 Macchine support
 
 config MACH_SMDK6400
@@ -276,6 +281,7 @@ config MACH_WLF_CRAGG_6410
 	select S3C64XX_SETUP_IDE
 	select S3C64XX_SETUP_FB_24BPP
 	select S3C64XX_SETUP_KEYPAD
+	select S3C64XX_SETUP_SPI
 	select SAMSUNG_DEV_ADC
 	select SAMSUNG_DEV_KEYPAD
 	select S3C_DEV_USB_HOST
@@ -286,7 +292,7 @@ config MACH_WLF_CRAGG_6410
 	select S3C_DEV_I2C1
 	select S3C_DEV_WDT
 	select S3C_DEV_RTC
-	select S3C64XX_DEV_SPI
+	select S3C64XX_DEV_SPI0
 	select S3C24XX_GPIO_EXTRA128
 	select I2C
 	help

arch/arm/mach-s3c64xx/Makefile

@@ -32,9 +32,9 @@ obj-$(CONFIG_S3C64XX_SETUP_I2C0) += setup-i2c0.o
 obj-$(CONFIG_S3C64XX_SETUP_I2C1) += setup-i2c1.o
 obj-$(CONFIG_S3C64XX_SETUP_IDE) += setup-ide.o
 obj-$(CONFIG_S3C64XX_SETUP_KEYPAD) += setup-keypad.o
-obj-$(CONFIG_S3C64XX_SETUP_SDHCI) += setup-sdhci.o
 obj-$(CONFIG_S3C64XX_SETUP_FB_24BPP) += setup-fb-24bpp.o
 obj-$(CONFIG_S3C64XX_SETUP_SDHCI_GPIO) += setup-sdhci-gpio.o
+obj-$(CONFIG_S3C64XX_SETUP_SPI) += setup-spi.o
 
 # PM
 
@@ -60,4 +60,3 @@ obj-$(CONFIG_MACH_WLF_CRAGG_6410) += mach-crag6410.o mach-crag6410-module.o
 
 obj-y				+= dev-uart.o
 obj-y				+= dev-audio.o
-obj-$(CONFIG_S3C64XX_DEV_SPI)	+= dev-spi.o

arch/arm/mach-s3c64xx/clock.c

@@ -183,18 +183,6 @@ static struct clk init_clocks_off[] = {
 		.parent		= &clk_p,
 		.enable		= s3c64xx_pclk_ctrl,
 		.ctrlbit	= S3C_CLKCON_PCLK_SPI1,
-	}, {
-		.name		= "spi_48m",
-		.devname	= "s3c64xx-spi.0",
-		.parent		= &clk_48m,
-		.enable		= s3c64xx_sclk_ctrl,
-		.ctrlbit	= S3C_CLKCON_SCLK_SPI0_48,
-	}, {
-		.name		= "spi_48m",
-		.devname	= "s3c64xx-spi.1",
-		.parent		= &clk_48m,
-		.enable		= s3c64xx_sclk_ctrl,
-		.ctrlbit	= S3C_CLKCON_SCLK_SPI1_48,
 	}, {
 		.name		= "48m",
 		.devname	= "s3c-sdhci.0",
@@ -226,6 +214,22 @@ static struct clk init_clocks_off[] = {
 	},
 };
 
+static struct clk clk_48m_spi0 = {
+	.name		= "spi_48m",
+	.devname	= "s3c64xx-spi.0",
+	.parent		= &clk_48m,
+	.enable		= s3c64xx_sclk_ctrl,
+	.ctrlbit	= S3C_CLKCON_SCLK_SPI0_48,
+};
+
+static struct clk clk_48m_spi1 = {
+	.name		= "spi_48m",
+	.devname	= "s3c64xx-spi.1",
+	.parent		= &clk_48m,
+	.enable		= s3c64xx_sclk_ctrl,
+	.ctrlbit	= S3C_CLKCON_SCLK_SPI1_48,
+};
+
 static struct clk init_clocks[] = {
 	{
 		.name		= "lcd",
@@ -242,24 +246,6 @@ static struct clk init_clocks[] = {
 		.parent		= &clk_h,
 		.enable		= s3c64xx_hclk_ctrl,
 		.ctrlbit	= S3C_CLKCON_HCLK_UHOST,
-	}, {
-		.name		= "hsmmc",
-		.devname	= "s3c-sdhci.0",
-		.parent		= &clk_h,
-		.enable		= s3c64xx_hclk_ctrl,
-		.ctrlbit	= S3C_CLKCON_HCLK_HSMMC0,
-	}, {
-		.name		= "hsmmc",
-		.devname	= "s3c-sdhci.1",
-		.parent		= &clk_h,
-		.enable		= s3c64xx_hclk_ctrl,
-		.ctrlbit	= S3C_CLKCON_HCLK_HSMMC1,
-	}, {
-		.name		= "hsmmc",
-		.devname	= "s3c-sdhci.2",
-		.parent		= &clk_h,
-		.enable		= s3c64xx_hclk_ctrl,
-		.ctrlbit	= S3C_CLKCON_HCLK_HSMMC2,
 	}, {
 		.name		= "otg",
 		.parent		= &clk_h,
@@ -310,6 +296,29 @@ static struct clk init_clocks[] = {
 	}
 };
 
+static struct clk clk_hsmmc0 = {
+	.name		= "hsmmc",
+	.devname	= "s3c-sdhci.0",
+	.parent		= &clk_h,
+	.enable		= s3c64xx_hclk_ctrl,
+	.ctrlbit	= S3C_CLKCON_HCLK_HSMMC0,
+};
+
+static struct clk clk_hsmmc1 = {
+	.name		= "hsmmc",
+	.devname	= "s3c-sdhci.1",
+	.parent		= &clk_h,
+	.enable		= s3c64xx_hclk_ctrl,
+	.ctrlbit	= S3C_CLKCON_HCLK_HSMMC1,
+};
+
+static struct clk clk_hsmmc2 = {
+	.name		= "hsmmc",
+	.devname	= "s3c-sdhci.2",
+	.parent		= &clk_h,
+	.enable		= s3c64xx_hclk_ctrl,
+	.ctrlbit	= S3C_CLKCON_HCLK_HSMMC2,
+};
 
 static struct clk clk_fout_apll = {
 	.name		= "fout_apll",
@@ -577,36 +586,6 @@ static struct clksrc_sources clkset_camif = {
 
 static struct clksrc_clk clksrcs[] = {
 	{
-		.clk	= {
-			.name		= "mmc_bus",
-			.devname	= "s3c-sdhci.0",
-			.ctrlbit        = S3C_CLKCON_SCLK_MMC0,
-			.enable		= s3c64xx_sclk_ctrl,
-		},
-		.reg_src	= { .reg = S3C_CLK_SRC, .shift = 18, .size = 2  },
-		.reg_div	= { .reg = S3C_CLK_DIV1, .shift = 0, .size = 4  },
-		.sources	= &clkset_spi_mmc,
-	}, {
-		.clk	= {
-			.name		= "mmc_bus",
-			.devname	= "s3c-sdhci.1",
-			.ctrlbit        = S3C_CLKCON_SCLK_MMC1,
-			.enable		= s3c64xx_sclk_ctrl,
-		},
-		.reg_src	= { .reg = S3C_CLK_SRC, .shift = 20, .size = 2  },
-		.reg_div	= { .reg = S3C_CLK_DIV1, .shift = 4, .size = 4  },
-		.sources	= &clkset_spi_mmc,
-	}, {
-		.clk	= {
-			.name		= "mmc_bus",
-			.devname	= "s3c-sdhci.2",
-			.ctrlbit        = S3C_CLKCON_SCLK_MMC2,
-			.enable		= s3c64xx_sclk_ctrl,
-		},
-		.reg_src	= { .reg = S3C_CLK_SRC, .shift = 22, .size = 2  },
-		.reg_div 	= { .reg = S3C_CLK_DIV1, .shift = 8, .size = 4  },
-		.sources	= &clkset_spi_mmc,
-	}, {
 		.clk	= {
 			.name		= "usb-bus-host",
 			.ctrlbit        = S3C_CLKCON_SCLK_UHOST,
@@ -615,35 +594,6 @@ static struct clksrc_clk clksrcs[] = {
 		.reg_src 	= { .reg = S3C_CLK_SRC, .shift = 5, .size = 2  },
 		.reg_div	= { .reg = S3C_CLK_DIV1, .shift = 20, .size = 4  },
 		.sources	= &clkset_uhost,
-	}, {
-		.clk	= {
-			.name		= "uclk1",
-			.ctrlbit        = S3C_CLKCON_SCLK_UART,
-			.enable		= s3c64xx_sclk_ctrl,
-		},
-		.reg_src	= { .reg = S3C_CLK_SRC, .shift = 13, .size = 1  },
-		.reg_div	= { .reg = S3C_CLK_DIV2, .shift = 16, .size = 4  },
-		.sources	= &clkset_uart,
-	}, {
-/* Where does UCLK0 come from? */
-		.clk	= {
-			.name		= "spi-bus",
-			.devname	= "s3c64xx-spi.0",
-			.ctrlbit        = S3C_CLKCON_SCLK_SPI0,
-			.enable		= s3c64xx_sclk_ctrl,
-		},
-		.reg_src	= { .reg = S3C_CLK_SRC, .shift = 14, .size = 2  },
-		.reg_div	= { .reg = S3C_CLK_DIV2, .shift = 0, .size = 4  },
-		.sources	= &clkset_spi_mmc,
-	}, {
-		.clk	= {
-			.name		= "spi-bus",
-			.devname	= "s3c64xx-spi.1",
-			.enable		= s3c64xx_sclk_ctrl,
-		},
-		.reg_src	= { .reg = S3C_CLK_SRC, .shift = 16, .size = 2  },
-		.reg_div	= { .reg = S3C_CLK_DIV2, .shift = 4, .size = 4  },
-		.sources	= &clkset_spi_mmc,
 	}, {
 		.clk	= {
 			.name		= "audio-bus",
@@ -695,6 +645,78 @@ static struct clksrc_clk clksrcs[] = {
 	},
 };
 
+/* Where does UCLK0 come from? */
+static struct clksrc_clk clk_sclk_uclk = {
+	.clk	= {
+		.name		= "uclk1",
+		.ctrlbit        = S3C_CLKCON_SCLK_UART,
+		.enable		= s3c64xx_sclk_ctrl,
+	},
+	.reg_src	= { .reg = S3C_CLK_SRC, .shift = 13, .size = 1  },
+	.reg_div	= { .reg = S3C_CLK_DIV2, .shift = 16, .size = 4  },
+	.sources	= &clkset_uart,
+};
+
+static struct clksrc_clk clk_sclk_mmc0 = {
+	.clk	= {
+		.name		= "mmc_bus",
+		.devname	= "s3c-sdhci.0",
+		.ctrlbit        = S3C_CLKCON_SCLK_MMC0,
+		.enable		= s3c64xx_sclk_ctrl,
+	},
+	.reg_src	= { .reg = S3C_CLK_SRC, .shift = 18, .size = 2  },
+	.reg_div	= { .reg = S3C_CLK_DIV1, .shift = 0, .size = 4  },
+	.sources	= &clkset_spi_mmc,
+};
+
+static struct clksrc_clk clk_sclk_mmc1 = {
+	.clk	= {
+		.name		= "mmc_bus",
+		.devname	= "s3c-sdhci.1",
+		.ctrlbit        = S3C_CLKCON_SCLK_MMC1,
+		.enable		= s3c64xx_sclk_ctrl,
+	},
+	.reg_src	= { .reg = S3C_CLK_SRC, .shift = 20, .size = 2  },
+	.reg_div	= { .reg = S3C_CLK_DIV1, .shift = 4, .size = 4  },
+	.sources	= &clkset_spi_mmc,
+};
+
+static struct clksrc_clk clk_sclk_mmc2 = {
+	.clk	= {
+		.name		= "mmc_bus",
+		.devname	= "s3c-sdhci.2",
+		.ctrlbit        = S3C_CLKCON_SCLK_MMC2,
+		.enable		= s3c64xx_sclk_ctrl,
+	},
+	.reg_src	= { .reg = S3C_CLK_SRC, .shift = 22, .size = 2  },
+	.reg_div	= { .reg = S3C_CLK_DIV1, .shift = 8, .size = 4  },
+	.sources	= &clkset_spi_mmc,
+};
+
+static struct clksrc_clk clk_sclk_spi0 = {
+	.clk	= {
+		.name		= "spi-bus",
+		.devname	= "s3c64xx-spi.0",
+		.ctrlbit	= S3C_CLKCON_SCLK_SPI0,
+		.enable		= s3c64xx_sclk_ctrl,
+	},
+	.reg_src = { .reg = S3C_CLK_SRC, .shift = 14, .size = 2 },
+	.reg_div = { .reg = S3C_CLK_DIV2, .shift = 0, .size = 4 },
+	.sources = &clkset_spi_mmc,
+};
+
+static struct clksrc_clk clk_sclk_spi1 = {
+	.clk	= {
+		.name		= "spi-bus",
+		.devname	= "s3c64xx-spi.1",
+		.ctrlbit	= S3C_CLKCON_SCLK_SPI1,
+		.enable		= s3c64xx_sclk_ctrl,
+	},
+	.reg_src = { .reg = S3C_CLK_SRC, .shift = 16, .size = 2 },
+	.reg_div = { .reg = S3C_CLK_DIV2, .shift = 4, .size = 4 },
+	.sources = &clkset_spi_mmc,
+};
+
 /* Clock initialisation code */
 
 static struct clksrc_clk *init_parents[] = {
@@ -703,6 +725,39 @@ static struct clksrc_clk *init_parents[] = {
 	&clk_mout_mpll,
 };
 
+static struct clksrc_clk *clksrc_cdev[] = {
+	&clk_sclk_uclk,
+	&clk_sclk_mmc0,
+	&clk_sclk_mmc1,
+	&clk_sclk_mmc2,
+	&clk_sclk_spi0,
+	&clk_sclk_spi1,
+};
+
+static struct clk *clk_cdev[] = {
+	&clk_hsmmc0,
+	&clk_hsmmc1,
+	&clk_hsmmc2,
+	&clk_48m_spi0,
+	&clk_48m_spi1,
+};
+
+static struct clk_lookup s3c64xx_clk_lookup[] = {
+	CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_p),
+	CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_sclk_uclk.clk),
+	CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.0", &clk_hsmmc0),
+	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.0", &clk_hsmmc1),
+	CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.0", &clk_hsmmc2),
+	CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.2", &clk_sclk_mmc0.clk),
+	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &clk_sclk_mmc1.clk),
+	CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.2", &clk_sclk_mmc2.clk),
+	CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
+	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
+	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk2", &clk_48m_spi0),
+	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
+	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk2", &clk_48m_spi1),
+};
+
 #define GET_DIV(clk, field) ((((clk) & field##_MASK) >> field##_SHIFT) + 1)
 
 void __init_or_cpufreq s3c6400_setup_clocks(void)
@@ -811,6 +866,8 @@ static struct clk *clks[] __initdata = {
 void __init s3c64xx_register_clocks(unsigned long xtal, 
 				    unsigned armclk_divlimit)
 {
+	unsigned int cnt;
+
 	armclk_mask = armclk_divlimit;
 
 	s3c24xx_register_baseclocks(xtal);
@@ -821,7 +878,15 @@ void __init s3c64xx_register_clocks(unsigned long xtal,
 	s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
 	s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
 
+	s3c24xx_register_clocks(clk_cdev, ARRAY_SIZE(clk_cdev));
+	for (cnt = 0; cnt < ARRAY_SIZE(clk_cdev); cnt++)
+		s3c_disable_clocks(clk_cdev[cnt], 1);
+
 	s3c24xx_register_clocks(clks1, ARRAY_SIZE(clks1));
 	s3c_register_clksrc(clksrcs, ARRAY_SIZE(clksrcs));
+	for (cnt = 0; cnt < ARRAY_SIZE(clksrc_cdev); cnt++)
+		s3c_register_clksrc(clksrc_cdev[cnt], 1);
+	clkdev_add_table(s3c64xx_clk_lookup, ARRAY_SIZE(s3c64xx_clk_lookup));
+
 	s3c_pwmclk_init();
 }

arch/arm/mach-s3c64xx/dev-spi.c

-/* linux/arch/arm/plat-s3c64xx/dev-spi.c
- *
- * Copyright (C) 2009 Samsung Electronics Ltd.
- *	Jaswinder Singh <jassi.brar@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/string.h>
-#include <linux/export.h>
-#include <linux/platform_device.h>
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-
-#include <mach/dma.h>
-#include <mach/map.h>
-#include <mach/spi-clocks.h>
-#include <mach/irqs.h>
-
-#include <plat/s3c64xx-spi.h>
-#include <plat/gpio-cfg.h>
-#include <plat/devs.h>
-
-static char *spi_src_clks[] = {
-	[S3C64XX_SPI_SRCCLK_PCLK] = "pclk",
-	[S3C64XX_SPI_SRCCLK_SPIBUS] = "spi-bus",
-	[S3C64XX_SPI_SRCCLK_48M] = "spi_48m",
-};
-
-/* SPI Controller platform_devices */
-
-/* Since we emulate multi-cs capability, we do not touch the GPC-3,7.
- * The emulated CS is toggled by board specific mechanism, as it can
- * be either some immediate GPIO or some signal out of some other
- * chip in between ... or some yet another way.
- * We simply do not assume anything about CS.
- */
-static int s3c64xx_spi_cfg_gpio(struct platform_device *pdev)
-{
-	unsigned int base;
-
-	switch (pdev->id) {
-	case 0:
-		base = S3C64XX_GPC(0);
-		break;
-
-	case 1:
-		base = S3C64XX_GPC(4);
-		break;
-
-	default:
-		dev_err(&pdev->dev, "Invalid SPI Controller number!");
-		return -EINVAL;
-	}
-
-	s3c_gpio_cfgall_range(base, 3,
-			      S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
-
-	return 0;
-}
-
-static struct resource s3c64xx_spi0_resource[] = {
-	[0] = {
-		.start = S3C64XX_PA_SPI0,
-		.end   = S3C64XX_PA_SPI0 + 0x100 - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = DMACH_SPI0_TX,
-		.end   = DMACH_SPI0_TX,
-		.flags = IORESOURCE_DMA,
-	},
-	[2] = {
-		.start = DMACH_SPI0_RX,
-		.end   = DMACH_SPI0_RX,
-		.flags = IORESOURCE_DMA,
-	},
-	[3] = {
-		.start = IRQ_SPI0,
-		.end   = IRQ_SPI0,
-		.flags = IORESOURCE_IRQ,
-	},
-};
-
-static struct s3c64xx_spi_info s3c64xx_spi0_pdata = {
-	.cfg_gpio = s3c64xx_spi_cfg_gpio,
-	.fifo_lvl_mask = 0x7f,
-	.rx_lvl_offset = 13,
-	.tx_st_done = 21,
-};
-
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-struct platform_device s3c64xx_device_spi0 = {
-	.name		  = "s3c64xx-spi",
-	.id		  = 0,
-	.num_resources	  = ARRAY_SIZE(s3c64xx_spi0_resource),
-	.resource	  = s3c64xx_spi0_resource,
-	.dev = {
-		.dma_mask		= &spi_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-		.platform_data = &s3c64xx_spi0_pdata,
-	},
-};
-EXPORT_SYMBOL(s3c64xx_device_spi0);
-
-static struct resource s3c64xx_spi1_resource[] = {
-	[0] = {
-		.start = S3C64XX_PA_SPI1,
-		.end   = S3C64XX_PA_SPI1 + 0x100 - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = DMACH_SPI1_TX,
-		.end   = DMACH_SPI1_TX,
-		.flags = IORESOURCE_DMA,
-	},
-	[2] = {
-		.start = DMACH_SPI1_RX,
-		.end   = DMACH_SPI1_RX,
-		.flags = IORESOURCE_DMA,
-	},
-	[3] = {
-		.start = IRQ_SPI1,
-		.end   = IRQ_SPI1,
-		.flags = IORESOURCE_IRQ,
-	},
-};
-
-static struct s3c64xx_spi_info s3c64xx_spi1_pdata = {
-	.cfg_gpio = s3c64xx_spi_cfg_gpio,
-	.fifo_lvl_mask = 0x7f,
-	.rx_lvl_offset = 13,
-	.tx_st_done = 21,
-};
-
-struct platform_device s3c64xx_device_spi1 = {
-	.name		  = "s3c64xx-spi",
-	.id		  = 1,
-	.num_resources	  = ARRAY_SIZE(s3c64xx_spi1_resource),
-	.resource	  = s3c64xx_spi1_resource,
-	.dev = {
-		.dma_mask		= &spi_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-		.platform_data = &s3c64xx_spi1_pdata,
-	},
-};
-EXPORT_SYMBOL(s3c64xx_device_spi1);
-
-void __init s3c64xx_spi_set_info(int cntrlr, int src_clk_nr, int num_cs)
-{
-	struct s3c64xx_spi_info *pd;
-
-	/* Reject invalid configuration */
-	if (!num_cs || src_clk_nr < 0
-			|| src_clk_nr > S3C64XX_SPI_SRCCLK_48M) {
-		printk(KERN_ERR "%s: Invalid SPI configuration\n", __func__);
-		return;
-	}
-
-	switch (cntrlr) {
-	case 0:
-		pd = &s3c64xx_spi0_pdata;
-		break;
-	case 1:
-		pd = &s3c64xx_spi1_pdata;
-		break;
-	default:
-		printk(KERN_ERR "%s: Invalid SPI controller(%d)\n",
-							__func__, cntrlr);
-		return;
-	}
-
-	pd->num_cs = num_cs;
-	pd->src_clk_nr = src_clk_nr;
-	pd->src_clk_name = spi_src_clks[src_clk_nr];
-}

arch/arm/mach-s3c64xx/include/mach/map.h

@@ -115,6 +115,8 @@
 #define S3C_PA_USB_HSOTG	S3C64XX_PA_USB_HSOTG
 #define S3C_PA_RTC		S3C64XX_PA_RTC
 #define S3C_PA_WDT		S3C64XX_PA_WATCHDOG
+#define S3C_PA_SPI0		S3C64XX_PA_SPI0
+#define S3C_PA_SPI1		S3C64XX_PA_SPI1
 
 #define SAMSUNG_PA_ADC		S3C64XX_PA_ADC
 #define SAMSUNG_PA_CFCON	S3C64XX_PA_CFCON

arch/arm/mach-s3c64xx/setup-sdhci.c

-/* linux/arch/arm/mach-s3c64xx/setup-sdhci.c
- *
- * Copyright 2008 Simtec Electronics
- * Copyright 2008 Simtec Electronics
- *	Ben Dooks <ben@simtec.co.uk>
- *	http://armlinux.simtec.co.uk/
- *
- * S3C6400/S3C6410 - Helper functions for settign up SDHCI device(s) (HSMMC)
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/types.h>
-
-/* clock sources for the mmc bus clock, order as for the ctrl2[5..4] */
-
-char *s3c64xx_hsmmc_clksrcs[4] = {
-	[0] = "hsmmc",
-	[1] = "hsmmc",
-	[2] = "mmc_bus",
-	/* [3] = "48m", - note not successfully used yet */
-};

arch/arm/mach-s3c64xx/setup-spi.c

+/* linux/arch/arm/mach-s3c64xx/setup-spi.c
+ *
+ * Copyright (C) 2011 Samsung Electronics Ltd.
+ *		http://www.samsung.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+
+#include <plat/gpio-cfg.h>
+#include <plat/s3c64xx-spi.h>
+
+#ifdef CONFIG_S3C64XX_DEV_SPI0
+struct s3c64xx_spi_info s3c64xx_spi0_pdata __initdata = {
+	.fifo_lvl_mask	= 0x7f,
+	.rx_lvl_offset	= 13,
+	.tx_st_done	= 21,
+};
+
+int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
+{
+	s3c_gpio_cfgall_range(S3C64XX_GPC(0), 3,
+				S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_S3C64XX_DEV_SPI1
+struct s3c64xx_spi_info s3c64xx_spi1_pdata __initdata = {
+	.fifo_lvl_mask	= 0x7f,
+	.rx_lvl_offset	= 13,
+	.tx_st_done	= 21,
+};
+
+int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
+{
+	s3c_gpio_cfgall_range(S3C64XX_GPC(4), 3,
+				S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+	return 0;
+}
+#endif

arch/arm/mach-s5p64x0/Kconfig

@@ -36,6 +36,11 @@ config S5P64X0_SETUP_I2C1
 	help
 	  Common setup code for i2c bus 1.
 
+config S5P64X0_SETUP_SPI
+	bool
+	help
+	  Common setup code for SPI GPIO configurations
+
 # machine support
 
 config MACH_SMDK6440
@@ -45,7 +50,6 @@ config MACH_SMDK6440
 	select S3C_DEV_I2C1
 	select S3C_DEV_RTC
 	select S3C_DEV_WDT
-	select S3C64XX_DEV_SPI
 	select SAMSUNG_DEV_ADC
 	select SAMSUNG_DEV_BACKLIGHT
 	select SAMSUNG_DEV_PWM
@@ -62,7 +66,6 @@ config MACH_SMDK6450
 	select S3C_DEV_I2C1
 	select S3C_DEV_RTC
 	select S3C_DEV_WDT
-	select S3C64XX_DEV_SPI
 	select SAMSUNG_DEV_ADC
 	select SAMSUNG_DEV_BACKLIGHT
 	select SAMSUNG_DEV_PWM

arch/arm/mach-s5p64x0/Makefile

@@ -26,7 +26,7 @@ obj-$(CONFIG_MACH_SMDK6450)	+= mach-smdk6450.o
 # device support
 
 obj-y				+= dev-audio.o
-obj-$(CONFIG_S3C64XX_DEV_SPI)	+= dev-spi.o
 
 obj-$(CONFIG_S5P64X0_SETUP_I2C1)	+= setup-i2c1.o
 obj-$(CONFIG_S5P64X0_SETUP_FB_24BPP)	+= setup-fb-24bpp.o
+obj-$(CONFIG_S5P64X0_SETUP_SPI)		+= setup-spi.o

arch/arm/mach-s5p64x0/clock-s5p6440.c

@@ -267,18 +267,6 @@ static struct clk init_clocks_off[] = {
 		.parent		= &clk_pclk.clk,
 		.enable		= s5p64x0_pclk_ctrl,
 		.ctrlbit	= (1 << 31),
-	}, {
-		.name		= "sclk_spi_48",
-		.devname	= "s3c64xx-spi.0",
-		.parent		= &clk_48m,
-		.enable		= s5p64x0_sclk_ctrl,
-		.ctrlbit	= (1 << 22),
-	}, {
-		.name		= "sclk_spi_48",
-		.devname	= "s3c64xx-spi.1",
-		.parent		= &clk_48m,
-		.enable		= s5p64x0_sclk_ctrl,
-		.ctrlbit	= (1 << 23),
 	}, {
 		.name		= "mmc_48m",
 		.devname	= "s3c-sdhci.0",
@@ -419,35 +407,6 @@ static struct clksrc_clk clksrcs[] = {
 		.sources = &clkset_group1,
 		.reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 22, .size = 2 },
 		.reg_div = { .reg = S5P64X0_CLK_DIV1, .shift = 8, .size = 4 },
-	}, {
-		.clk	= {
-			.name		= "uclk1",
-			.ctrlbit	= (1 << 5),
-			.enable		= s5p64x0_sclk_ctrl,
-		},
-		.sources = &clkset_uart,
-		.reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 13, .size = 1 },
-		.reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 16, .size = 4 },
-	}, {
-		.clk	= {
-			.name		= "sclk_spi",
-			.devname	= "s3c64xx-spi.0",
-			.ctrlbit	= (1 << 20),
-			.enable		= s5p64x0_sclk_ctrl,
-		},
-		.sources = &clkset_group1,
-		.reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 14, .size = 2 },
-		.reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 0, .size = 4 },
-	}, {
-		.clk	= {
-			.name		= "sclk_spi",
-			.devname	= "s3c64xx-spi.1",
-			.ctrlbit	= (1 << 21),
-			.enable		= s5p64x0_sclk_ctrl,
-		},
-		.sources = &clkset_group1,
-		.reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 16, .size = 2 },
-		.reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 4, .size = 4 },
 	}, {
 		.clk	= {
 			.name		= "sclk_post",
@@ -487,6 +446,41 @@ static struct clksrc_clk clksrcs[] = {
 	},
 };
 
+static struct clksrc_clk clk_sclk_uclk = {
+	.clk	= {
+		.name		= "uclk1",
+		.ctrlbit	= (1 << 5),
+		.enable		= s5p64x0_sclk_ctrl,
+	},
+	.sources = &clkset_uart,
+	.reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 13, .size = 1 },
+	.reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 16, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_spi0 = {
+	.clk	= {
+		.name		= "sclk_spi",
+		.devname	= "s3c64xx-spi.0",
+		.ctrlbit	= (1 << 20),
+		.enable		= s5p64x0_sclk_ctrl,
+	},
+	.sources = &clkset_group1,
+	.reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 14, .size = 2 },
+	.reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 0, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_spi1 = {
+	.clk	= {
+		.name		= "sclk_spi",
+		.devname	= "s3c64xx-spi.1",
+		.ctrlbit	= (1 << 21),
+		.enable		= s5p64x0_sclk_ctrl,
+	},
+	.sources = &clkset_group1,
+	.reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 16, .size = 2 },
+	.reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 4, .size = 4 },
+};
+
 /* Clock initialization code */
 static struct clksrc_clk *sysclks[] = {
 	&clk_mout_apll,
@@ -505,6 +499,20 @@ static struct clk dummy_apb_pclk = {
 	.id		= -1,
 };
 
+static struct clksrc_clk *clksrc_cdev[] = {
+	&clk_sclk_uclk,
+	&clk_sclk_spi0,
+	&clk_sclk_spi1,
+};
+
+static struct clk_lookup s5p6440_clk_lookup[] = {
+	CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_pclk_low.clk),
+	CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_sclk_uclk.clk),
+	CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
+	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
+	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
+};
+
 void __init_or_cpufreq s5p6440_setup_clocks(void)
 {
 	struct clk *xtal_clk;
@@ -583,9 +591,12 @@ void __init s5p6440_register_clocks(void)
 
 	s3c_register_clksrc(clksrcs, ARRAY_SIZE(clksrcs));
 	s3c_register_clocks(init_clocks, ARRAY_SIZE(init_clocks));
+	for (ptr = 0; ptr < ARRAY_SIZE(clksrc_cdev); ptr++)
+		s3c_register_clksrc(clksrc_cdev[ptr], 1);
 
 	s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
 	s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
+	clkdev_add_table(s5p6440_clk_lookup, ARRAY_SIZE(s5p6440_clk_lookup));
 
 	s3c24xx_register_clock(&dummy_apb_pclk);
 

arch/arm/mach-s5p64x0/clock-s5p6450.c

@@ -441,35 +441,6 @@ static struct clksrc_clk clksrcs[] = {
 		.sources = &clkset_group2,
 		.reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 22, .size = 2 },
 		.reg_div = { .reg = S5P64X0_CLK_DIV1, .shift = 8, .size = 4 },
-	}, {
-		.clk	= {
-			.name		= "uclk1",
-			.ctrlbit	= (1 << 5),
-			.enable		= s5p64x0_sclk_ctrl,
-		},
-		.sources = &clkset_uart,
-		.reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 13, .size = 1 },
-		.reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 16, .size = 4 },
-	}, {
-		.clk	= {
-			.name		= "sclk_spi",
-			.devname	= "s3c64xx-spi.0",
-			.ctrlbit	= (1 << 20),
-			.enable		= s5p64x0_sclk_ctrl,
-		},
-		.sources = &clkset_group2,
-		.reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 14, .size = 2 },
-		.reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 0, .size = 4 },
-	}, {
-		.clk	= {
-			.name		= "sclk_spi",
-			.devname	= "s3c64xx-spi.1",
-			.ctrlbit	= (1 << 21),
-			.enable		= s5p64x0_sclk_ctrl,
-		},
-		.sources = &clkset_group2,
-		.reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 16, .size = 2 },
-		.reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 4, .size = 4 },
 	}, {
 		.clk	= {
 			.name		= "sclk_fimc",
@@ -536,6 +507,55 @@ static struct clksrc_clk clksrcs[] = {
 	},
 };
 
+static struct clksrc_clk clk_sclk_uclk = {
+	.clk	= {
+		.name		= "uclk1",
+		.ctrlbit	= (1 << 5),
+		.enable		= s5p64x0_sclk_ctrl,
+	},
+	.sources = &clkset_uart,
+	.reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 13, .size = 1 },
+	.reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 16, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_spi0 = {
+	.clk	= {
+		.name		= "sclk_spi",
+		.devname	= "s3c64xx-spi.0",
+		.ctrlbit	= (1 << 20),
+		.enable		= s5p64x0_sclk_ctrl,
+	},
+	.sources = &clkset_group2,
+	.reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 14, .size = 2 },
+	.reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 0, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_spi1 = {
+	.clk	= {
+		.name		= "sclk_spi",
+		.devname	= "s3c64xx-spi.1",
+		.ctrlbit	= (1 << 21),
+		.enable		= s5p64x0_sclk_ctrl,
+	},
+	.sources = &clkset_group2,
+	.reg_src = { .reg = S5P64X0_CLK_SRC0, .shift = 16, .size = 2 },
+	.reg_div = { .reg = S5P64X0_CLK_DIV2, .shift = 4, .size = 4 },
+};
+
+static struct clksrc_clk *clksrc_cdev[] = {
+	&clk_sclk_uclk,
+	&clk_sclk_spi0,
+	&clk_sclk_spi1,
+};
+
+static struct clk_lookup s5p6450_clk_lookup[] = {
+	CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_pclk_low.clk),
+	CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_sclk_uclk.clk),
+	CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
+	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
+	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
+};
+
 /* Clock initialization code */
 static struct clksrc_clk *sysclks[] = {
 	&clk_mout_apll,
@@ -634,9 +654,12 @@ void __init s5p6450_register_clocks(void)
 
 	s3c_register_clksrc(clksrcs, ARRAY_SIZE(clksrcs));
 	s3c_register_clocks(init_clocks, ARRAY_SIZE(init_clocks));
+	for (ptr = 0; ptr < ARRAY_SIZE(clksrc_cdev); ptr++)
+		s3c_register_clksrc(clksrc_cdev[ptr], 1);
 
 	s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
 	s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
+	clkdev_add_table(s5p6450_clk_lookup, ARRAY_SIZE(s5p6450_clk_lookup));
 
 	s3c24xx_register_clock(&dummy_apb_pclk);
 

arch/arm/mach-s5p64x0/dev-spi.c

-/* linux/arch/arm/mach-s5p64x0/dev-spi.c
- *
- * Copyright (c) 2010 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com
- *
- * Copyright (C) 2010 Samsung Electronics Co. Ltd.
- *	Jaswinder Singh <jassi.brar@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/platform_device.h>
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-
-#include <mach/dma.h>
-#include <mach/map.h>
-#include <mach/irqs.h>
-#include <mach/regs-clock.h>
-#include <mach/spi-clocks.h>
-
-#include <plat/cpu.h>
-#include <plat/s3c64xx-spi.h>
-#include <plat/gpio-cfg.h>
-
-static char *s5p64x0_spi_src_clks[] = {
-	[S5P64X0_SPI_SRCCLK_PCLK] = "pclk",
-	[S5P64X0_SPI_SRCCLK_SCLK] = "sclk_spi",
-};
-
-/* SPI Controller platform_devices */
-
-/* Since we emulate multi-cs capability, we do not touch the CS.
- * The emulated CS is toggled by board specific mechanism, as it can
- * be either some immediate GPIO or some signal out of some other
- * chip in between ... or some yet another way.
- * We simply do not assume anything about CS.
- */
-static int s5p6440_spi_cfg_gpio(struct platform_device *pdev)
-{
-	unsigned int base;
-
-	switch (pdev->id) {
-	case 0:
-		base = S5P6440_GPC(0);
-		break;
-
-	case 1:
-		base = S5P6440_GPC(4);
-		break;
-
-	default:
-		dev_err(&pdev->dev, "Invalid SPI Controller number!");
-		return -EINVAL;
-	}
-
-	s3c_gpio_cfgall_range(base, 3,
-			      S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
-
-	return 0;
-}
-
-static int s5p6450_spi_cfg_gpio(struct platform_device *pdev)
-{
-	unsigned int base;
-
-	switch (pdev->id) {
-	case 0:
-		base = S5P6450_GPC(0);
-		break;
-
-	case 1:
-		base = S5P6450_GPC(4);
-		break;
-
-	default:
-		dev_err(&pdev->dev, "Invalid SPI Controller number!");
-		return -EINVAL;
-	}
-
-	s3c_gpio_cfgall_range(base, 3,
-			      S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
-
-	return 0;
-}
-
-static struct resource s5p64x0_spi0_resource[] = {
-	[0] = {
-		.start	= S5P64X0_PA_SPI0,
-		.end	= S5P64X0_PA_SPI0 + 0x100 - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= DMACH_SPI0_TX,
-		.end	= DMACH_SPI0_TX,
-		.flags	= IORESOURCE_DMA,
-	},
-	[2] = {
-		.start	= DMACH_SPI0_RX,
-		.end	= DMACH_SPI0_RX,
-		.flags	= IORESOURCE_DMA,
-	},
-	[3] = {
-		.start	= IRQ_SPI0,
-		.end	= IRQ_SPI0,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct s3c64xx_spi_info s5p6440_spi0_pdata = {
-	.cfg_gpio	= s5p6440_spi_cfg_gpio,
-	.fifo_lvl_mask	= 0x1ff,
-	.rx_lvl_offset	= 15,
-	.tx_st_done	= 25,
-};
-
-static struct s3c64xx_spi_info s5p6450_spi0_pdata = {
-	.cfg_gpio	= s5p6450_spi_cfg_gpio,
-	.fifo_lvl_mask	= 0x1ff,
-	.rx_lvl_offset	= 15,
-	.tx_st_done	= 25,
-};
-
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-struct platform_device s5p64x0_device_spi0 = {
-	.name		= "s3c64xx-spi",
-	.id		= 0,
-	.num_resources	= ARRAY_SIZE(s5p64x0_spi0_resource),
-	.resource	= s5p64x0_spi0_resource,
-	.dev = {
-		.dma_mask		= &spi_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-};
-
-static struct resource s5p64x0_spi1_resource[] = {
-	[0] = {
-		.start	= S5P64X0_PA_SPI1,
-		.end	= S5P64X0_PA_SPI1 + 0x100 - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= DMACH_SPI1_TX,
-		.end	= DMACH_SPI1_TX,
-		.flags	= IORESOURCE_DMA,
-	},
-	[2] = {
-		.start	= DMACH_SPI1_RX,
-		.end	= DMACH_SPI1_RX,
-		.flags	= IORESOURCE_DMA,
-	},
-	[3] = {
-		.start	= IRQ_SPI1,
-		.end	= IRQ_SPI1,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct s3c64xx_spi_info s5p6440_spi1_pdata = {
-	.cfg_gpio	= s5p6440_spi_cfg_gpio,
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 15,
-	.tx_st_done	= 25,
-};
-
-static struct s3c64xx_spi_info s5p6450_spi1_pdata = {
-	.cfg_gpio	= s5p6450_spi_cfg_gpio,
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 15,
-	.tx_st_done	= 25,
-};
-
-struct platform_device s5p64x0_device_spi1 = {
-	.name		= "s3c64xx-spi",
-	.id		= 1,
-	.num_resources	= ARRAY_SIZE(s5p64x0_spi1_resource),
-	.resource	= s5p64x0_spi1_resource,
-	.dev = {
-		.dma_mask		= &spi_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-};
-
-void __init s5p64x0_spi_set_info(int cntrlr, int src_clk_nr, int num_cs)
-{
-	struct s3c64xx_spi_info *pd;
-
-	/* Reject invalid configuration */
-	if (!num_cs || src_clk_nr < 0
-			|| src_clk_nr > S5P64X0_SPI_SRCCLK_SCLK) {
-		printk(KERN_ERR "%s: Invalid SPI configuration\n", __func__);
-		return;
-	}
-
-	switch (cntrlr) {
-	case 0:
-		if (soc_is_s5p6450())
-			pd = &s5p6450_spi0_pdata;
-		else
-			pd = &s5p6440_spi0_pdata;
-
-		s5p64x0_device_spi0.dev.platform_data = pd;
-		break;
-	case 1:
-		if (soc_is_s5p6450())
-			pd = &s5p6450_spi1_pdata;
-		else
-			pd = &s5p6440_spi1_pdata;
-
-		s5p64x0_device_spi1.dev.platform_data = pd;
-		break;
-	default:
-		printk(KERN_ERR "%s: Invalid SPI controller(%d)\n",
-							__func__, cntrlr);
-		return;
-	}
-
-	pd->num_cs = num_cs;
-	pd->src_clk_nr = src_clk_nr;
-	pd->src_clk_name = s5p64x0_spi_src_clks[src_clk_nr];
-}

arch/arm/mach-s5p64x0/dma.c

@@ -38,176 +38,74 @@
 
 static u64 dma_dmamask = DMA_BIT_MASK(32);
 
-struct dma_pl330_peri s5p6440_pdma_peri[22] = {
-	{
-		.peri_id = (u8)DMACH_UART0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_UART1_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART1_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_UART2_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART2_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_UART3_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART3_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = DMACH_MAX,
-	}, {
-		.peri_id = DMACH_MAX,
-	}, {
-		.peri_id = (u8)DMACH_PCM0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_PCM0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_I2S0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_I2S0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_SPI0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_SPI0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_MAX,
-	}, {
-		.peri_id = (u8)DMACH_MAX,
-	}, {
-		.peri_id = (u8)DMACH_MAX,
-	}, {
-		.peri_id = (u8)DMACH_MAX,
-	}, {
-		.peri_id = (u8)DMACH_SPI1_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_SPI1_RX,
-		.rqtype = DEVTOMEM,
-	},
+u8 s5p6440_pdma_peri[] = {
+	DMACH_UART0_RX,
+	DMACH_UART0_TX,
+	DMACH_UART1_RX,
+	DMACH_UART1_TX,
+	DMACH_UART2_RX,
+	DMACH_UART2_TX,
+	DMACH_UART3_RX,
+	DMACH_UART3_TX,
+	DMACH_MAX,
+	DMACH_MAX,
+	DMACH_PCM0_TX,
+	DMACH_PCM0_RX,
+	DMACH_I2S0_TX,
+	DMACH_I2S0_RX,
+	DMACH_SPI0_TX,
+	DMACH_SPI0_RX,
+	DMACH_MAX,
+	DMACH_MAX,
+	DMACH_MAX,
+	DMACH_MAX,
+	DMACH_SPI1_TX,
+	DMACH_SPI1_RX,
 };
 
 struct dma_pl330_platdata s5p6440_pdma_pdata = {
 	.nr_valid_peri = ARRAY_SIZE(s5p6440_pdma_peri),
-	.peri = s5p6440_pdma_peri,
+	.peri_id = s5p6440_pdma_peri,
 };
 
-struct dma_pl330_peri s5p6450_pdma_peri[32] = {
-	{
-		.peri_id = (u8)DMACH_UART0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_UART1_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART1_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_UART2_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART2_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_UART3_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART3_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_UART4_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART4_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_PCM0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_PCM0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_I2S0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_I2S0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_SPI0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_SPI0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_PCM1_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_PCM1_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_PCM2_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_PCM2_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_SPI1_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_SPI1_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_USI_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_USI_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_MAX,
-	}, {
-		.peri_id = (u8)DMACH_I2S1_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_I2S1_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_I2S2_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_I2S2_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_PWM,
-	}, {
-		.peri_id = (u8)DMACH_UART5_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART5_TX,
-		.rqtype = MEMTODEV,
-	},
+u8 s5p6450_pdma_peri[] = {
+	DMACH_UART0_RX,
+	DMACH_UART0_TX,
+	DMACH_UART1_RX,
+	DMACH_UART1_TX,
+	DMACH_UART2_RX,
+	DMACH_UART2_TX,
+	DMACH_UART3_RX,
+	DMACH_UART3_TX,
+	DMACH_UART4_RX,
+	DMACH_UART4_TX,
+	DMACH_PCM0_TX,
+	DMACH_PCM0_RX,
+	DMACH_I2S0_TX,
+	DMACH_I2S0_RX,
+	DMACH_SPI0_TX,
+	DMACH_SPI0_RX,
+	DMACH_PCM1_TX,
+	DMACH_PCM1_RX,
+	DMACH_PCM2_TX,
+	DMACH_PCM2_RX,
+	DMACH_SPI1_TX,
+	DMACH_SPI1_RX,
+	DMACH_USI_TX,
+	DMACH_USI_RX,
+	DMACH_MAX,
+	DMACH_I2S1_TX,
+	DMACH_I2S1_RX,
+	DMACH_I2S2_TX,
+	DMACH_I2S2_RX,
+	DMACH_PWM,
+	DMACH_UART5_RX,
+	DMACH_UART5_TX,
 };
 
 struct dma_pl330_platdata s5p6450_pdma_pdata = {
 	.nr_valid_peri = ARRAY_SIZE(s5p6450_pdma_peri),
-	.peri = s5p6450_pdma_peri,
+	.peri_id = s5p6450_pdma_peri,
 };
 
 struct amba_device s5p64x0_device_pdma = {
@@ -227,10 +125,15 @@ struct amba_device s5p64x0_device_pdma = {
 
 static int __init s5p64x0_dma_init(void)
 {
-	if (soc_is_s5p6450())
+	if (soc_is_s5p6450()) {
+		dma_cap_set(DMA_SLAVE, s5p6450_pdma_pdata.cap_mask);
+		dma_cap_set(DMA_CYCLIC, s5p6450_pdma_pdata.cap_mask);
 		s5p64x0_device_pdma.dev.platform_data = &s5p6450_pdma_pdata;
-	else
+	} else {
+		dma_cap_set(DMA_SLAVE, s5p6440_pdma_pdata.cap_mask);
+		dma_cap_set(DMA_CYCLIC, s5p6440_pdma_pdata.cap_mask);
 		s5p64x0_device_pdma.dev.platform_data = &s5p6440_pdma_pdata;
+	}
 
 	amba_device_register(&s5p64x0_device_pdma, &iomem_resource);
 

arch/arm/mach-s5p64x0/include/mach/irqs.h

@@ -141,6 +141,8 @@
 
 #define IRQ_EINT_GROUP(grp, x)	(IRQ_EINT_GROUP##grp##_BASE + (x))
 
+#define IRQ_TIMER_BASE		(11)
+
 /* Set the default NR_IRQS */
 
 #define NR_IRQS			(IRQ_EINT_GROUP8_BASE + IRQ_EINT_GROUP8_NR + 1)

arch/arm/mach-s5p64x0/include/mach/map.h

@@ -67,6 +67,8 @@
 #define S3C_PA_RTC		S5P64X0_PA_RTC
 #define S3C_PA_WDT		S5P64X0_PA_WDT
 #define S3C_PA_FB		S5P64X0_PA_FB
+#define S3C_PA_SPI0		S5P64X0_PA_SPI0
+#define S3C_PA_SPI1		S5P64X0_PA_SPI1
 
 #define S5P_PA_CHIPID		S5P64X0_PA_CHIPID
 #define S5P_PA_SROMC		S5P64X0_PA_SROMC

arch/arm/mach-s5p64x0/init.c

@@ -23,36 +23,7 @@
 #include <plat/s5p6450.h>
 #include <plat/regs-serial.h>
 
-static struct s3c24xx_uart_clksrc s5p64x0_serial_clocks[] = {
-	[0] = {
-		.name		= "pclk_low",
-		.divisor	= 1,
-		.min_baud	= 0,
-		.max_baud	= 0,
-	},
-	[1] = {
-		.name		= "uclk1",
-		.divisor	= 1,
-		.min_baud	= 0,
-		.max_baud	= 0,
-	},
-};
-
 /* uart registration process */
-
-void __init s5p64x0_common_init_uarts(struct s3c2410_uartcfg *cfg, int no)
-{
-	struct s3c2410_uartcfg *tcfg = cfg;
-	u32 ucnt;
-
-	for (ucnt = 0; ucnt < no; ucnt++, tcfg++) {
-		if (!tcfg->clocks) {
-			tcfg->clocks = s5p64x0_serial_clocks;
-			tcfg->clocks_size = ARRAY_SIZE(s5p64x0_serial_clocks);
-		}
-	}
-}
-
 void __init s5p6440_init_uarts(struct s3c2410_uartcfg *cfg, int no)
 {
 	int uart;
@@ -62,12 +33,10 @@ void __init s5p6440_init_uarts(struct s3c2410_uartcfg *cfg, int no)
 		s5p_uart_resources[uart].resources->end = S5P6440_PA_UART(uart) + S5P_SZ_UART;
 	}
 
-	s5p64x0_common_init_uarts(cfg, no);
 	s3c24xx_init_uartdevs("s3c6400-uart", s5p_uart_resources, cfg, no);
 }
 
 void __init s5p6450_init_uarts(struct s3c2410_uartcfg *cfg, int no)
 {
-	s5p64x0_common_init_uarts(cfg, no);
 	s3c24xx_init_uartdevs("s3c6400-uart", s5p_uart_resources, cfg, no);
 }

arch/arm/mach-s5p64x0/setup-spi.c

+/* linux/arch/arm/mach-s5p64x0/setup-spi.c
+ *
+ * Copyright (C) 2011 Samsung Electronics Ltd.
+ *		http://www.samsung.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+
+#include <plat/gpio-cfg.h>
+#include <plat/cpu.h>
+#include <plat/s3c64xx-spi.h>
+
+#ifdef CONFIG_S3C64XX_DEV_SPI0
+struct s3c64xx_spi_info s3c64xx_spi0_pdata __initdata = {
+	.fifo_lvl_mask	= 0x1ff,
+	.rx_lvl_offset	= 15,
+	.tx_st_done	= 25,
+};
+
+int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
+{
+	if (soc_is_s5p6450())
+		s3c_gpio_cfgall_range(S5P6450_GPC(0), 3,
+					S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+	else
+		s3c_gpio_cfgall_range(S5P6440_GPC(0), 3,
+					S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_S3C64XX_DEV_SPI1
+struct s3c64xx_spi_info s3c64xx_spi1_pdata __initdata = {
+	.fifo_lvl_mask	= 0x7f,
+	.rx_lvl_offset	= 15,
+	.tx_st_done	= 25,
+};
+
+int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
+{
+	if (soc_is_s5p6450())
+		s3c_gpio_cfgall_range(S5P6450_GPC(4), 3,
+					S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+	else
+		s3c_gpio_cfgall_range(S5P6440_GPC(4), 3,
+					S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+	return 0;
+}
+#endif

arch/arm/mach-s5pc100/Kconfig

@@ -45,6 +45,11 @@ config S5PC100_SETUP_SDHCI_GPIO
 	help
 	  Common setup code for SDHCI gpio.
 
+config S5PC100_SETUP_SPI
+	bool
+	help
+	  Common setup code for SPI GPIO configurations.
+
 config MACH_SMDKC100
 	bool "SMDKC100"
 	select CPU_S5PC100

arch/arm/mach-s5pc100/Makefile

@@ -21,12 +21,11 @@ obj-$(CONFIG_S5PC100_SETUP_FB_24BPP)	+= setup-fb-24bpp.o
 obj-$(CONFIG_S5PC100_SETUP_I2C1)	+= setup-i2c1.o
 obj-$(CONFIG_S5PC100_SETUP_IDE)		+= setup-ide.o
 obj-$(CONFIG_S5PC100_SETUP_KEYPAD)	+= setup-keypad.o
-obj-$(CONFIG_S5PC100_SETUP_SDHCI)	+= setup-sdhci.o
 obj-$(CONFIG_S5PC100_SETUP_SDHCI_GPIO)	+= setup-sdhci-gpio.o
+obj-$(CONFIG_S5PC100_SETUP_SPI)	+= setup-spi.o
 
 # device support
 obj-y				+= dev-audio.o
-obj-$(CONFIG_S3C64XX_DEV_SPI)	+= dev-spi.o
 
 # machine support
 

arch/arm/mach-s5pc100/clock.c

@@ -425,24 +425,6 @@ static struct clk init_clocks_off[] = {
 		.parent		= &clk_div_d0_bus.clk,
 		.enable		= s5pc100_d0_2_ctrl,
 		.ctrlbit	= (1 << 1),
-	}, {
-		.name		= "hsmmc",
-		.devname	= "s3c-sdhci.2",
-		.parent		= &clk_div_d1_bus.clk,
-		.enable		= s5pc100_d1_0_ctrl,
-		.ctrlbit	= (1 << 7),
-	}, {
-		.name		= "hsmmc",
-		.devname	= "s3c-sdhci.1",
-		.parent		= &clk_div_d1_bus.clk,
-		.enable		= s5pc100_d1_0_ctrl,
-		.ctrlbit	= (1 << 6),
-	}, {
-		.name		= "hsmmc",
-		.devname	= "s3c-sdhci.0",
-		.parent		= &clk_div_d1_bus.clk,
-		.enable		= s5pc100_d1_0_ctrl,
-		.ctrlbit	= (1 << 5),
 	}, {
 		.name		= "modemif",
 		.parent		= &clk_div_d1_bus.clk,
@@ -672,24 +654,6 @@ static struct clk init_clocks_off[] = {
 		.parent		= &clk_div_pclkd1.clk,
 		.enable		= s5pc100_d1_5_ctrl,
 		.ctrlbit	= (1 << 8),
-	}, {
-		.name		= "spi_48m",
-		.devname	= "s3c64xx-spi.0",
-		.parent		= &clk_mout_48m.clk,
-		.enable		= s5pc100_sclk0_ctrl,
-		.ctrlbit	= (1 << 7),
-	}, {
-		.name		= "spi_48m",
-		.devname	= "s3c64xx-spi.1",
-		.parent		= &clk_mout_48m.clk,
-		.enable		= s5pc100_sclk0_ctrl,
-		.ctrlbit	= (1 << 8),
-	}, {
-		.name		= "spi_48m",
-		.devname	= "s3c64xx-spi.2",
-		.parent		= &clk_mout_48m.clk,
-		.enable		= s5pc100_sclk0_ctrl,
-		.ctrlbit	= (1 << 9),
 	}, {
 		.name		= "mmc_48m",
 		.devname	= "s3c-sdhci.0",
@@ -711,6 +675,54 @@ static struct clk init_clocks_off[] = {
 	},
 };
 
+static struct clk clk_hsmmc2 = {
+	.name		= "hsmmc",
+	.devname	= "s3c-sdhci.2",
+	.parent		= &clk_div_d1_bus.clk,
+	.enable		= s5pc100_d1_0_ctrl,
+	.ctrlbit	= (1 << 7),
+};
+
+static struct clk clk_hsmmc1 = {
+	.name		= "hsmmc",
+	.devname	= "s3c-sdhci.1",
+	.parent		= &clk_div_d1_bus.clk,
+	.enable		= s5pc100_d1_0_ctrl,
+	.ctrlbit	= (1 << 6),
+};
+
+static struct clk clk_hsmmc0 = {
+	.name		= "hsmmc",
+	.devname	= "s3c-sdhci.0",
+	.parent		= &clk_div_d1_bus.clk,
+	.enable		= s5pc100_d1_0_ctrl,
+	.ctrlbit	= (1 << 5),
+};
+
+static struct clk clk_48m_spi0 = {
+	.name		= "spi_48m",
+	.devname	= "s3c64xx-spi.0",
+	.parent		= &clk_mout_48m.clk,
+	.enable		= s5pc100_sclk0_ctrl,
+	.ctrlbit	= (1 << 7),
+};
+
+static struct clk clk_48m_spi1 = {
+	.name		= "spi_48m",
+	.devname	= "s3c64xx-spi.1",
+	.parent		= &clk_mout_48m.clk,
+	.enable		= s5pc100_sclk0_ctrl,
+	.ctrlbit	= (1 << 8),
+};
+
+static struct clk clk_48m_spi2 = {
+	.name		= "spi_48m",
+	.devname	= "s3c64xx-spi.2",
+	.parent		= &clk_mout_48m.clk,
+	.enable		= s5pc100_sclk0_ctrl,
+	.ctrlbit	= (1 << 9),
+};
+
 static struct clk clk_vclk54m = {
 	.name		= "vclk_54m",
 	.rate		= 54000000,
@@ -928,49 +940,6 @@ static struct clksrc_clk clk_sclk_spdif = {
 
 static struct clksrc_clk clksrcs[] = {
 	{
-		.clk	= {
-			.name		= "sclk_spi",
-			.devname	= "s3c64xx-spi.0",
-			.ctrlbit	= (1 << 4),
-			.enable		= s5pc100_sclk0_ctrl,
-
-		},
-		.sources = &clk_src_group1,
-		.reg_src = { .reg = S5P_CLK_SRC1, .shift = 4, .size = 2 },
-		.reg_div = { .reg = S5P_CLK_DIV2, .shift = 4, .size = 4 },
-	}, {
-		.clk	= {
-			.name		= "sclk_spi",
-			.devname	= "s3c64xx-spi.1",
-			.ctrlbit	= (1 << 5),
-			.enable		= s5pc100_sclk0_ctrl,
-
-		},
-		.sources = &clk_src_group1,
-		.reg_src = { .reg = S5P_CLK_SRC1, .shift = 8, .size = 2 },
-		.reg_div = { .reg = S5P_CLK_DIV2, .shift = 8, .size = 4 },
-	}, {
-		.clk	= {
-			.name		= "sclk_spi",
-			.devname	= "s3c64xx-spi.2",
-			.ctrlbit	= (1 << 6),
-			.enable		= s5pc100_sclk0_ctrl,
-
-		},
-		.sources = &clk_src_group1,
-		.reg_src = { .reg = S5P_CLK_SRC1, .shift = 12, .size = 2 },
-		.reg_div = { .reg = S5P_CLK_DIV2, .shift = 12, .size = 4 },
-	}, {
-		.clk	= {
-			.name		= "uclk1",
-			.ctrlbit	= (1 << 3),
-			.enable		= s5pc100_sclk0_ctrl,
-
-		},
-		.sources = &clk_src_group2,
-		.reg_src = { .reg = S5P_CLK_SRC1, .shift = 0, .size = 1 },
-		.reg_div = { .reg = S5P_CLK_DIV2, .shift = 0, .size = 4 },
-	}, {
 		.clk	= {
 			.name		= "sclk_mixer",
 			.ctrlbit	= (1 << 6),
@@ -1022,39 +991,6 @@ static struct clksrc_clk clksrcs[] = {
 		.sources = &clk_src_group7,
 		.reg_src = { .reg = S5P_CLK_SRC2, .shift = 24, .size = 2 },
 		.reg_div = { .reg = S5P_CLK_DIV3, .shift = 24, .size = 4 },
-	}, {
-		.clk	= {
-			.name		= "sclk_mmc",
-			.devname	= "s3c-sdhci.0",
-			.ctrlbit	= (1 << 12),
-			.enable		= s5pc100_sclk1_ctrl,
-
-		},
-		.sources = &clk_src_mmc0,
-		.reg_src = { .reg = S5P_CLK_SRC2, .shift = 0, .size = 2 },
-		.reg_div = { .reg = S5P_CLK_DIV3, .shift = 0, .size = 4 },
-	}, {
-		.clk	= {
-			.name		= "sclk_mmc",
-			.devname	= "s3c-sdhci.1",
-			.ctrlbit	= (1 << 13),
-			.enable		= s5pc100_sclk1_ctrl,
-
-		},
-		.sources = &clk_src_mmc12,
-		.reg_src = { .reg = S5P_CLK_SRC2, .shift = 4, .size = 2 },
-		.reg_div = { .reg = S5P_CLK_DIV3, .shift = 4, .size = 4 },
-	}, {
-		.clk	= {
-			.name		= "sclk_mmc",
-			.devname	= "s3c-sdhci.2",
-			.ctrlbit	= (1 << 14),
-			.enable		= s5pc100_sclk1_ctrl,
-
-		},
-		.sources = &clk_src_mmc12,
-		.reg_src = { .reg = S5P_CLK_SRC2, .shift = 8, .size = 2 },
-		.reg_div = { .reg = S5P_CLK_DIV3, .shift = 8, .size = 4 },
 	}, {
 		.clk	= {
 			.name		= "sclk_irda",
@@ -1098,6 +1034,89 @@ static struct clksrc_clk clksrcs[] = {
 	},
 };
 
+static struct clksrc_clk clk_sclk_uart = {
+	.clk	= {
+		.name		= "uclk1",
+		.ctrlbit	= (1 << 3),
+		.enable		= s5pc100_sclk0_ctrl,
+	},
+	.sources = &clk_src_group2,
+	.reg_src = { .reg = S5P_CLK_SRC1, .shift = 0, .size = 1 },
+	.reg_div = { .reg = S5P_CLK_DIV2, .shift = 0, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_mmc0 = {
+	.clk	= {
+		.name		= "sclk_mmc",
+		.devname	= "s3c-sdhci.0",
+		.ctrlbit	= (1 << 12),
+		.enable		= s5pc100_sclk1_ctrl,
+	},
+	.sources = &clk_src_mmc0,
+	.reg_src = { .reg = S5P_CLK_SRC2, .shift = 0, .size = 2 },
+	.reg_div = { .reg = S5P_CLK_DIV3, .shift = 0, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_mmc1 = {
+	.clk	= {
+		.name		= "sclk_mmc",
+		.devname	= "s3c-sdhci.1",
+		.ctrlbit	= (1 << 13),
+		.enable		= s5pc100_sclk1_ctrl,
+	},
+	.sources = &clk_src_mmc12,
+	.reg_src = { .reg = S5P_CLK_SRC2, .shift = 4, .size = 2 },
+	.reg_div = { .reg = S5P_CLK_DIV3, .shift = 4, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_mmc2 = {
+	.clk	= {
+		.name		= "sclk_mmc",
+		.devname	= "s3c-sdhci.2",
+		.ctrlbit	= (1 << 14),
+		.enable		= s5pc100_sclk1_ctrl,
+	},
+	.sources = &clk_src_mmc12,
+	.reg_src = { .reg = S5P_CLK_SRC2, .shift = 8, .size = 2 },
+	.reg_div = { .reg = S5P_CLK_DIV3, .shift = 8, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_spi0 = {
+	.clk	= {
+		.name		= "sclk_spi",
+		.devname	= "s3c64xx-spi.0",
+		.ctrlbit	= (1 << 4),
+		.enable		= s5pc100_sclk0_ctrl,
+	},
+	.sources = &clk_src_group1,
+	.reg_src = { .reg = S5P_CLK_SRC1, .shift = 4, .size = 2 },
+	.reg_div = { .reg = S5P_CLK_DIV2, .shift = 4, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_spi1 = {
+	.clk	= {
+		.name		= "sclk_spi",
+		.devname	= "s3c64xx-spi.1",
+		.ctrlbit	= (1 << 5),
+		.enable		= s5pc100_sclk0_ctrl,
+	},
+	.sources = &clk_src_group1,
+	.reg_src = { .reg = S5P_CLK_SRC1, .shift = 8, .size = 2 },
+	.reg_div = { .reg = S5P_CLK_DIV2, .shift = 8, .size = 4 },
+};
+
+static struct clksrc_clk clk_sclk_spi2 = {
+	.clk	= {
+		.name		= "sclk_spi",
+		.devname	= "s3c64xx-spi.2",
+		.ctrlbit	= (1 << 6),
+		.enable		= s5pc100_sclk0_ctrl,
+	},
+	.sources = &clk_src_group1,
+	.reg_src = { .reg = S5P_CLK_SRC1, .shift = 12, .size = 2 },
+	.reg_div = { .reg = S5P_CLK_DIV2, .shift = 12, .size = 4 },
+};
+
 /* Clock initialisation code */
 static struct clksrc_clk *sysclks[] = {
 	&clk_mout_apll,
@@ -1127,6 +1146,25 @@ static struct clksrc_clk *sysclks[] = {
 	&clk_sclk_spdif,
 };
 
+static struct clk *clk_cdev[] = {
+	&clk_hsmmc0,
+	&clk_hsmmc1,
+	&clk_hsmmc2,
+	&clk_48m_spi0,
+	&clk_48m_spi1,
+	&clk_48m_spi2,
+};
+
+static struct clksrc_clk *clksrc_cdev[] = {
+	&clk_sclk_uart,
+	&clk_sclk_mmc0,
+	&clk_sclk_mmc1,
+	&clk_sclk_mmc2,
+	&clk_sclk_spi0,
+	&clk_sclk_spi1,
+	&clk_sclk_spi2,
+};
+
 void __init_or_cpufreq s5pc100_setup_clocks(void)
 {
 	unsigned long xtal;
@@ -1266,6 +1304,24 @@ static struct clk *clks[] __initdata = {
 	&clk_pcmcdclk1,
 };
 
+static struct clk_lookup s5pc100_clk_lookup[] = {
+	CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_p),
+	CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_sclk_uart.clk),
+	CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.0", &clk_hsmmc0),
+	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.0", &clk_hsmmc1),
+	CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.0", &clk_hsmmc2),
+	CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.2", &clk_sclk_mmc0.clk),
+	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &clk_sclk_mmc1.clk),
+	CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.2", &clk_sclk_mmc2.clk),
+	CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
+	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk1", &clk_48m_spi0),
+	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk2", &clk_sclk_spi0.clk),
+	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk1", &clk_48m_spi1),
+	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk2", &clk_sclk_spi1.clk),
+	CLKDEV_INIT("s3c64xx-spi.2", "spi_busclk1", &clk_48m_spi2),
+	CLKDEV_INIT("s3c64xx-spi.2", "spi_busclk2", &clk_sclk_spi2.clk),
+};
+
 void __init s5pc100_register_clocks(void)
 {
 	int ptr;
@@ -1277,9 +1333,16 @@ void __init s5pc100_register_clocks(void)
 
 	s3c_register_clksrc(clksrcs, ARRAY_SIZE(clksrcs));
 	s3c_register_clocks(init_clocks, ARRAY_SIZE(init_clocks));
+	for (ptr = 0; ptr < ARRAY_SIZE(clksrc_cdev); ptr++)
+		s3c_register_clksrc(clksrc_cdev[ptr], 1);
 
 	s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
 	s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
+	clkdev_add_table(s5pc100_clk_lookup, ARRAY_SIZE(s5pc100_clk_lookup));
+
+	s3c24xx_register_clocks(clk_cdev, ARRAY_SIZE(clk_cdev));
+	for (ptr = 0; ptr < ARRAY_SIZE(clk_cdev); ptr++)
+		s3c_disable_clocks(clk_cdev[ptr], 1);
 
 	s3c24xx_register_clock(&dummy_apb_pclk);
 

arch/arm/mach-s5pc100/dev-spi.c

-/* linux/arch/arm/mach-s5pc100/dev-spi.c
- *
- * Copyright (C) 2010 Samsung Electronics Co. Ltd.
- *	Jaswinder Singh <jassi.brar@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/platform_device.h>
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-
-#include <mach/dma.h>
-#include <mach/map.h>
-#include <mach/spi-clocks.h>
-#include <mach/irqs.h>
-
-#include <plat/s3c64xx-spi.h>
-#include <plat/gpio-cfg.h>
-#include <plat/irqs.h>
-
-static char *spi_src_clks[] = {
-	[S5PC100_SPI_SRCCLK_PCLK] = "pclk",
-	[S5PC100_SPI_SRCCLK_48M] = "spi_48m",
-	[S5PC100_SPI_SRCCLK_SPIBUS] = "spi_bus",
-};
-
-/* SPI Controller platform_devices */
-
-/* Since we emulate multi-cs capability, we do not touch the CS.
- * The emulated CS is toggled by board specific mechanism, as it can
- * be either some immediate GPIO or some signal out of some other
- * chip in between ... or some yet another way.
- * We simply do not assume anything about CS.
- */
-static int s5pc100_spi_cfg_gpio(struct platform_device *pdev)
-{
-	switch (pdev->id) {
-	case 0:
-		s3c_gpio_cfgall_range(S5PC100_GPB(0), 3,
-				      S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
-		break;
-
-	case 1:
-		s3c_gpio_cfgall_range(S5PC100_GPB(4), 3,
-				      S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
-		break;
-
-	case 2:
-		s3c_gpio_cfgpin(S5PC100_GPG3(0), S3C_GPIO_SFN(3));
-		s3c_gpio_setpull(S5PC100_GPG3(0), S3C_GPIO_PULL_UP);
-		s3c_gpio_cfgall_range(S5PC100_GPB(2), 2,
-				      S3C_GPIO_SFN(3), S3C_GPIO_PULL_UP);
-		break;
-
-	default:
-		dev_err(&pdev->dev, "Invalid SPI Controller number!");
-		return -EINVAL;
-	}
-
-	return 0;
-}
-
-static struct resource s5pc100_spi0_resource[] = {
-	[0] = {
-		.start = S5PC100_PA_SPI0,
-		.end   = S5PC100_PA_SPI0 + 0x100 - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = DMACH_SPI0_TX,
-		.end   = DMACH_SPI0_TX,
-		.flags = IORESOURCE_DMA,
-	},
-	[2] = {
-		.start = DMACH_SPI0_RX,
-		.end   = DMACH_SPI0_RX,
-		.flags = IORESOURCE_DMA,
-	},
-	[3] = {
-		.start = IRQ_SPI0,
-		.end   = IRQ_SPI0,
-		.flags = IORESOURCE_IRQ,
-	},
-};
-
-static struct s3c64xx_spi_info s5pc100_spi0_pdata = {
-	.cfg_gpio = s5pc100_spi_cfg_gpio,
-	.fifo_lvl_mask = 0x7f,
-	.rx_lvl_offset = 13,
-	.high_speed = 1,
-	.tx_st_done = 21,
-};
-
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-struct platform_device s5pc100_device_spi0 = {
-	.name		  = "s3c64xx-spi",
-	.id		  = 0,
-	.num_resources	  = ARRAY_SIZE(s5pc100_spi0_resource),
-	.resource	  = s5pc100_spi0_resource,
-	.dev = {
-		.dma_mask		= &spi_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-		.platform_data = &s5pc100_spi0_pdata,
-	},
-};
-
-static struct resource s5pc100_spi1_resource[] = {
-	[0] = {
-		.start = S5PC100_PA_SPI1,
-		.end   = S5PC100_PA_SPI1 + 0x100 - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = DMACH_SPI1_TX,
-		.end   = DMACH_SPI1_TX,
-		.flags = IORESOURCE_DMA,
-	},
-	[2] = {
-		.start = DMACH_SPI1_RX,
-		.end   = DMACH_SPI1_RX,
-		.flags = IORESOURCE_DMA,
-	},
-	[3] = {
-		.start = IRQ_SPI1,
-		.end   = IRQ_SPI1,
-		.flags = IORESOURCE_IRQ,
-	},
-};
-
-static struct s3c64xx_spi_info s5pc100_spi1_pdata = {
-	.cfg_gpio = s5pc100_spi_cfg_gpio,
-	.fifo_lvl_mask = 0x7f,
-	.rx_lvl_offset = 13,
-	.high_speed = 1,
-	.tx_st_done = 21,
-};
-
-struct platform_device s5pc100_device_spi1 = {
-	.name		  = "s3c64xx-spi",
-	.id		  = 1,
-	.num_resources	  = ARRAY_SIZE(s5pc100_spi1_resource),
-	.resource	  = s5pc100_spi1_resource,
-	.dev = {
-		.dma_mask		= &spi_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-		.platform_data = &s5pc100_spi1_pdata,
-	},
-};
-
-static struct resource s5pc100_spi2_resource[] = {
-	[0] = {
-		.start = S5PC100_PA_SPI2,
-		.end   = S5PC100_PA_SPI2 + 0x100 - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = DMACH_SPI2_TX,
-		.end   = DMACH_SPI2_TX,
-		.flags = IORESOURCE_DMA,
-	},
-	[2] = {
-		.start = DMACH_SPI2_RX,
-		.end   = DMACH_SPI2_RX,
-		.flags = IORESOURCE_DMA,
-	},
-	[3] = {
-		.start = IRQ_SPI2,
-		.end   = IRQ_SPI2,
-		.flags = IORESOURCE_IRQ,
-	},
-};
-
-static struct s3c64xx_spi_info s5pc100_spi2_pdata = {
-	.cfg_gpio = s5pc100_spi_cfg_gpio,
-	.fifo_lvl_mask = 0x7f,
-	.rx_lvl_offset = 13,
-	.high_speed = 1,
-	.tx_st_done = 21,
-};
-
-struct platform_device s5pc100_device_spi2 = {
-	.name		  = "s3c64xx-spi",
-	.id		  = 2,
-	.num_resources	  = ARRAY_SIZE(s5pc100_spi2_resource),
-	.resource	  = s5pc100_spi2_resource,
-	.dev = {
-		.dma_mask		= &spi_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-		.platform_data = &s5pc100_spi2_pdata,
-	},
-};
-
-void __init s5pc100_spi_set_info(int cntrlr, int src_clk_nr, int num_cs)
-{
-	struct s3c64xx_spi_info *pd;
-
-	/* Reject invalid configuration */
-	if (!num_cs || src_clk_nr < 0
-			|| src_clk_nr > S5PC100_SPI_SRCCLK_SPIBUS) {
-		printk(KERN_ERR "%s: Invalid SPI configuration\n", __func__);
-		return;
-	}
-
-	switch (cntrlr) {
-	case 0:
-		pd = &s5pc100_spi0_pdata;
-		break;
-	case 1:
-		pd = &s5pc100_spi1_pdata;
-		break;
-	case 2:
-		pd = &s5pc100_spi2_pdata;
-		break;
-	default:
-		printk(KERN_ERR "%s: Invalid SPI controller(%d)\n",
-							__func__, cntrlr);
-		return;
-	}
-
-	pd->num_cs = num_cs;
-	pd->src_clk_nr = src_clk_nr;
-	pd->src_clk_name = spi_src_clks[src_clk_nr];
-}

arch/arm/mach-s5pc100/dma.c

@@ -35,100 +35,42 @@
 
 static u64 dma_dmamask = DMA_BIT_MASK(32);
 
-struct dma_pl330_peri pdma0_peri[30] = {
-	{
-		.peri_id = (u8)DMACH_UART0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_UART1_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART1_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_UART2_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART2_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_UART3_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART3_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = DMACH_IRDA,
-	}, {
-		.peri_id = (u8)DMACH_I2S0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_I2S0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_I2S0S_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_I2S1_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_I2S1_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_I2S2_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_I2S2_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_SPI0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_SPI0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_SPI1_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_SPI1_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_SPI2_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_SPI2_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_AC97_MICIN,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_AC97_PCMIN,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_AC97_PCMOUT,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_EXTERNAL,
-	}, {
-		.peri_id = (u8)DMACH_PWM,
-	}, {
-		.peri_id = (u8)DMACH_SPDIF,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_HSI_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_HSI_TX,
-		.rqtype = MEMTODEV,
-	},
+u8 pdma0_peri[] = {
+	DMACH_UART0_RX,
+	DMACH_UART0_TX,
+	DMACH_UART1_RX,
+	DMACH_UART1_TX,
+	DMACH_UART2_RX,
+	DMACH_UART2_TX,
+	DMACH_UART3_RX,
+	DMACH_UART3_TX,
+	DMACH_IRDA,
+	DMACH_I2S0_RX,
+	DMACH_I2S0_TX,
+	DMACH_I2S0S_TX,
+	DMACH_I2S1_RX,
+	DMACH_I2S1_TX,
+	DMACH_I2S2_RX,
+	DMACH_I2S2_TX,
+	DMACH_SPI0_RX,
+	DMACH_SPI0_TX,
+	DMACH_SPI1_RX,
+	DMACH_SPI1_TX,
+	DMACH_SPI2_RX,
+	DMACH_SPI2_TX,
+	DMACH_AC97_MICIN,
+	DMACH_AC97_PCMIN,
+	DMACH_AC97_PCMOUT,
+	DMACH_EXTERNAL,
+	DMACH_PWM,
+	DMACH_SPDIF,
+	DMACH_HSI_RX,
+	DMACH_HSI_TX,
 };
 
 struct dma_pl330_platdata s5pc100_pdma0_pdata = {
 	.nr_valid_peri = ARRAY_SIZE(pdma0_peri),
-	.peri = pdma0_peri,
+	.peri_id = pdma0_peri,
 };
 
 struct amba_device s5pc100_device_pdma0 = {
@@ -147,98 +89,42 @@ struct amba_device s5pc100_device_pdma0 = {
 	.periphid = 0x00041330,
 };
 
-struct dma_pl330_peri pdma1_peri[30] = {
-	{
-		.peri_id = (u8)DMACH_UART0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_UART1_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART1_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_UART2_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART2_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_UART3_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_UART3_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = DMACH_IRDA,
-	}, {
-		.peri_id = (u8)DMACH_I2S0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_I2S0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_I2S0S_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_I2S1_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_I2S1_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_I2S2_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_I2S2_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_SPI0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_SPI0_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_SPI1_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_SPI1_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_SPI2_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_SPI2_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_PCM0_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_PCM1_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_PCM1_RX,
-		.rqtype = DEVTOMEM,
-	}, {
-		.peri_id = (u8)DMACH_PCM1_TX,
-		.rqtype = MEMTODEV,
-	}, {
-		.peri_id = (u8)DMACH_MSM_REQ0,
-	}, {
-		.peri_id = (u8)DMACH_MSM_REQ1,
-	}, {
-		.peri_id = (u8)DMACH_MSM_REQ2,
-	}, {
-		.peri_id = (u8)DMACH_MSM_REQ3,
-	},
+u8 pdma1_peri[] = {
+	DMACH_UART0_RX,
+	DMACH_UART0_TX,
+	DMACH_UART1_RX,
+	DMACH_UART1_TX,
+	DMACH_UART2_RX,
+	DMACH_UART2_TX,
+	DMACH_UART3_RX,
+	DMACH_UART3_TX,
+	DMACH_IRDA,
+	DMACH_I2S0_RX,
+	DMACH_I2S0_TX,
+	DMACH_I2S0S_TX,
+	DMACH_I2S1_RX,
+	DMACH_I2S1_TX,
+	DMACH_I2S2_RX,
+	DMACH_I2S2_TX,
+	DMACH_SPI0_RX,
+	DMACH_SPI0_TX,
+	DMACH_SPI1_RX,
+	DMACH_SPI1_TX,
+	DMACH_SPI2_RX,
+	DMACH_SPI2_TX,
+	DMACH_PCM0_RX,
+	DMACH_PCM0_TX,
+	DMACH_PCM1_RX,
+	DMACH_PCM1_TX,
+	DMACH_MSM_REQ0,
+	DMACH_MSM_REQ1,
+	DMACH_MSM_REQ2,
+	DMACH_MSM_REQ3,
 };
 
 struct dma_pl330_platdata s5pc100_pdma1_pdata = {
 	.nr_valid_peri = ARRAY_SIZE(pdma1_peri),
-	.peri = pdma1_peri,
+	.peri_id = pdma1_peri,
 };
 
 struct amba_device s5pc100_device_pdma1 = {
@@ -259,7 +145,12 @@ struct amba_device s5pc100_device_pdma1 = {
 
 static int __init s5pc100_dma_init(void)
 {
+	dma_cap_set(DMA_SLAVE, s5pc100_pdma0_pdata.cap_mask);
+	dma_cap_set(DMA_CYCLIC, s5pc100_pdma0_pdata.cap_mask);
 	amba_device_register(&s5pc100_device_pdma0, &iomem_resource);
+
+	dma_cap_set(DMA_SLAVE, s5pc100_pdma1_pdata.cap_mask);
+	dma_cap_set(DMA_CYCLIC, s5pc100_pdma1_pdata.cap_mask);
 	amba_device_register(&s5pc100_device_pdma1, &iomem_resource);
 
 	return 0;

arch/arm/mach-s5pc100/include/mach/irqs.h

@@ -97,6 +97,8 @@
 #define IRQ_SDMFIQ		S5P_IRQ_VIC2(31)
 #define IRQ_VIC_END		S5P_IRQ_VIC2(31)
 
+#define IRQ_TIMER_BASE		(11)
+
 #define S5P_EINT_BASE1		(S5P_IRQ_VIC0(0))
 #define S5P_EINT_BASE2		(IRQ_VIC_END + 1)
 

arch/arm/mach-s5pc100/include/mach/map.h

@@ -100,6 +100,9 @@
 #define S3C_PA_USB_HSOTG		S5PC100_PA_USB_HSOTG
 #define S3C_PA_USB_HSPHY		S5PC100_PA_USB_HSPHY
 #define S3C_PA_WDT			S5PC100_PA_WATCHDOG
+#define S3C_PA_SPI0			S5PC100_PA_SPI0
+#define S3C_PA_SPI1			S5PC100_PA_SPI1
+#define S3C_PA_SPI2			S5PC100_PA_SPI2
 
 #define S5P_PA_CHIPID			S5PC100_PA_CHIPID
 #define S5P_PA_FIMC0			S5PC100_PA_FIMC0

arch/arm/mach-s5pc100/setup-sdhci.c

-/* linux/arch/arm/mach-s5pc100/setup-sdhci.c
- *
- * Copyright 2008 Samsung Electronics
- *
- * S5PC100 - Helper functions for settign up SDHCI device(s) (HSMMC)
- *
- * Based on mach-s3c6410/setup-sdhci.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/types.h>
-
-/* clock sources for the mmc bus clock, order as for the ctrl2[5..4] */
-
-char *s5pc100_hsmmc_clksrcs[4] = {
-	[0] = "hsmmc",		/* HCLK */
-	/* [1] = "hsmmc",	- duplicate HCLK entry */
-	[2] = "sclk_mmc",	/* mmc_bus */
-	/* [3] = "48m",		- note not successfully used yet */
-};

arch/arm/mach-s5pc100/setup-spi.c

+/* linux/arch/arm/mach-s5pc100/setup-spi.c
+ *
+ * Copyright (C) 2011 Samsung Electronics Ltd.
+ *		http://www.samsung.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+
+#include <plat/gpio-cfg.h>
+#include <plat/s3c64xx-spi.h>
+
+#ifdef CONFIG_S3C64XX_DEV_SPI0
+struct s3c64xx_spi_info s3c64xx_spi0_pdata __initdata = {
+	.fifo_lvl_mask	= 0x7f,
+	.rx_lvl_offset	= 13,
+	.high_speed	= 1,
+	.tx_st_done	= 21,
+};
+
+int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
+{
+	s3c_gpio_cfgall_range(S5PC100_GPB(0), 3,
+				S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_S3C64XX_DEV_SPI1
+struct s3c64xx_spi_info s3c64xx_spi1_pdata __initdata = {
+	.fifo_lvl_mask	= 0x7f,
+	.rx_lvl_offset	= 13,
+	.high_speed	= 1,
+	.tx_st_done	= 21,
+};
+
+int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
+{
+	s3c_gpio_cfgall_range(S5PC100_GPB(4), 3,
+				S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_S3C64XX_DEV_SPI2
+struct s3c64xx_spi_info s3c64xx_spi2_pdata __initdata = {
+	.fifo_lvl_mask	= 0x7f,
+	.rx_lvl_offset	= 13,
+	.high_speed	= 1,
+	.tx_st_done	= 21,
+};
+
+int s3c64xx_spi2_cfg_gpio(struct platform_device *dev)
+{
+	s3c_gpio_cfgpin(S5PC100_GPG3(0), S3C_GPIO_SFN(3));
+	s3c_gpio_setpull(S5PC100_GPG3(0), S3C_GPIO_PULL_UP);
+	s3c_gpio_cfgall_range(S5PC100_GPB(2), 2,
+				S3C_GPIO_SFN(3), S3C_GPIO_PULL_UP);
+	return 0;
+}
+#endif

arch/arm/mach-s5pv210/Kconfig

@@ -60,6 +60,11 @@ config S5PV210_SETUP_FIMC
 	help
 	  Common setup code for the camera interfaces.
 
+config S5PV210_SETUP_SPI
+	bool
+	help
+	  Common setup code for SPI GPIO configurations.
+
 menu "S5PC110 Machines"
 
 config MACH_AQUILA

arch/arm/mach-s5pv210/Makefile

@@ -27,7 +27,6 @@ obj-$(CONFIG_MACH_TORBRECK)	+= mach-torbreck.o
 # device support
 
 obj-y				+= dev-audio.o
-obj-$(CONFIG_S3C64XX_DEV_SPI)	+= dev-spi.o
 
 obj-$(CONFIG_S5PV210_SETUP_FB_24BPP)	+= setup-fb-24bpp.o
 obj-$(CONFIG_S5PV210_SETUP_FIMC)	+= setup-fimc.o
@@ -35,5 +34,5 @@ obj-$(CONFIG_S5PV210_SETUP_I2C1) 	+= setup-i2c1.o
 obj-$(CONFIG_S5PV210_SETUP_I2C2) 	+= setup-i2c2.o
 obj-$(CONFIG_S5PV210_SETUP_IDE)		+= setup-ide.o
 obj-$(CONFIG_S5PV210_SETUP_KEYPAD)	+= setup-keypad.o
-obj-$(CONFIG_S5PV210_SETUP_SDHCI)       += setup-sdhci.o
 obj-$(CONFIG_S5PV210_SETUP_SDHCI_GPIO)	+= setup-sdhci-gpio.o
+obj-$(CONFIG_S5PV210_SETUP_SPI)		+= setup-spi.o

arch/arm/mach-s5pv210/dev-spi.c

-/* linux/arch/arm/mach-s5pv210/dev-spi.c
- *
- * Copyright (C) 2010 Samsung Electronics Co. Ltd.
- *	Jaswinder Singh <jassi.brar@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/platform_device.h>
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-
-#include <mach/dma.h>
-#include <mach/map.h>
-#include <mach/irqs.h>
-#include <mach/spi-clocks.h>
-
-#include <plat/s3c64xx-spi.h>
-#include <plat/gpio-cfg.h>
-
-static char *spi_src_clks[] = {
-	[S5PV210_SPI_SRCCLK_PCLK] = "pclk",
-	[S5PV210_SPI_SRCCLK_SCLK] = "sclk_spi",
-};
-
-/* SPI Controller platform_devices */
-
-/* Since we emulate multi-cs capability, we do not touch the CS.
- * The emulated CS is toggled by board specific mechanism, as it can
- * be either some immediate GPIO or some signal out of some other
- * chip in between ... or some yet another way.
- * We simply do not assume anything about CS.
- */
-static int s5pv210_spi_cfg_gpio(struct platform_device *pdev)
-{
-	unsigned int base;
-
-	switch (pdev->id) {
-	case 0:
-		base = S5PV210_GPB(0);
-		break;
-
-	case 1:
-		base = S5PV210_GPB(4);
-		break;
-
-	default:
-		dev_err(&pdev->dev, "Invalid SPI Controller number!");
-		return -EINVAL;
-	}
-
-	s3c_gpio_cfgall_range(base, 3,
-			      S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
-
-	return 0;
-}
-
-static struct resource s5pv210_spi0_resource[] = {
-	[0] = {
-		.start = S5PV210_PA_SPI0,
-		.end   = S5PV210_PA_SPI0 + 0x100 - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = DMACH_SPI0_TX,
-		.end   = DMACH_SPI0_TX,
-		.flags = IORESOURCE_DMA,
-	},
-	[2] = {
-		.start = DMACH_SPI0_RX,
-		.end   = DMACH_SPI0_RX,
-		.flags = IORESOURCE_DMA,
-	},
-	[3] = {
-		.start = IRQ_SPI0,
-		.end   = IRQ_SPI0,
-		.flags = IORESOURCE_IRQ,
-	},
-};
-
-static struct s3c64xx_spi_info s5pv210_spi0_pdata = {
-	.cfg_gpio = s5pv210_spi_cfg_gpio,
-	.fifo_lvl_mask = 0x1ff,
-	.rx_lvl_offset = 15,
-	.high_speed = 1,
-	.tx_st_done = 25,
-};
-
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-struct platform_device s5pv210_device_spi0 = {
-	.name		  = "s3c64xx-spi",
-	.id		  = 0,
-	.num_resources	  = ARRAY_SIZE(s5pv210_spi0_resource),
-	.resource	  = s5pv210_spi0_resource,
-	.dev = {
-		.dma_mask		= &spi_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-		.platform_data = &s5pv210_spi0_pdata,
-	},
-};
-
-static struct resource s5pv210_spi1_resource[] = {
-	[0] = {
-		.start = S5PV210_PA_SPI1,
-		.end   = S5PV210_PA_SPI1 + 0x100 - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = DMACH_SPI1_TX,
-		.end   = DMACH_SPI1_TX,
-		.flags = IORESOURCE_DMA,
-	},
-	[2] = {
-		.start = DMACH_SPI1_RX,
-		.end   = DMACH_SPI1_RX,
-		.flags = IORESOURCE_DMA,
-	},
-	[3] = {
-		.start = IRQ_SPI1,
-		.end   = IRQ_SPI1,
-		.flags = IORESOURCE_IRQ,
-	},
-};
-
-static struct s3c64xx_spi_info s5pv210_spi1_pdata = {
-	.cfg_gpio = s5pv210_spi_cfg_gpio,
-	.fifo_lvl_mask = 0x7f,
-	.rx_lvl_offset = 15,
-	.high_speed = 1,
-	.tx_st_done = 25,
-};
-
-struct platform_device s5pv210_device_spi1 = {
-	.name		  = "s3c64xx-spi",
-	.id		  = 1,
-	.num_resources	  = ARRAY_SIZE(s5pv210_spi1_resource),
-	.resource	  = s5pv210_spi1_resource,
-	.dev = {
-		.dma_mask		= &spi_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-		.platform_data = &s5pv210_spi1_pdata,
-	},
-};
-
-void __init s5pv210_spi_set_info(int cntrlr, int src_clk_nr, int num_cs)
-{
-	struct s3c64xx_spi_info *pd;
-
-	/* Reject invalid configuration */
-	if (!num_cs || src_clk_nr < 0
-			|| src_clk_nr > S5PV210_SPI_SRCCLK_SCLK) {
-		printk(KERN_ERR "%s: Invalid SPI configuration\n", __func__);
-		return;
-	}
-
-	switch (cntrlr) {
-	case 0:
-		pd = &s5pv210_spi0_pdata;
-		break;
-	case 1:
-		pd = &s5pv210_spi1_pdata;
-		break;
-	default:
-		printk(KERN_ERR "%s: Invalid SPI controller(%d)\n",
-							__func__, cntrlr);
-		return;
-	}
-
-	pd->num_cs = num_cs;
-	pd->src_clk_nr = src_clk_nr;
-	pd->src_clk_name = spi_src_clks[src_clk_nr];
-}

arch/arm/mach-s5pv210/include/mach/irqs.h

@@ -118,6 +118,8 @@
 #define IRQ_MDNIE3		S5P_IRQ_VIC3(8)
 #define IRQ_VIC_END		S5P_IRQ_VIC3(31)
 
+#define IRQ_TIMER_BASE		(11)
+
 #define S5P_EINT_BASE1		(S5P_IRQ_VIC0(0))
 #define S5P_EINT_BASE2		(IRQ_VIC_END + 1)
 

arch/arm/mach-s5pv210/include/mach/map.h

@@ -109,6 +109,8 @@
 #define S3C_PA_RTC			S5PV210_PA_RTC
 #define S3C_PA_USB_HSOTG		S5PV210_PA_HSOTG
 #define S3C_PA_WDT			S5PV210_PA_WATCHDOG
+#define S3C_PA_SPI0			S5PV210_PA_SPI0
+#define S3C_PA_SPI1			S5PV210_PA_SPI1
 
 #define S5P_PA_CHIPID			S5PV210_PA_CHIPID
 #define S5P_PA_FIMC0			S5PV210_PA_FIMC0

arch/arm/mach-s5pv210/init.c

@@ -18,27 +18,8 @@
 #include <plat/s5pv210.h>
 #include <plat/regs-serial.h>
 
-static struct s3c24xx_uart_clksrc s5pv210_serial_clocks[] = {
-	[0] = {
-		.name		= "pclk",
-		.divisor	= 1,
-		.min_baud	= 0,
-		.max_baud	= 0,
-	},
-};
-
 /* uart registration process */
 void __init s5pv210_common_init_uarts(struct s3c2410_uartcfg *cfg, int no)
 {
-	struct s3c2410_uartcfg *tcfg = cfg;
-	u32 ucnt;
-
-	for (ucnt = 0; ucnt < no; ucnt++, tcfg++) {
-		if (!tcfg->clocks) {
-			tcfg->clocks = s5pv210_serial_clocks;
-			tcfg->clocks_size = ARRAY_SIZE(s5pv210_serial_clocks);
-		}
-	}
-
 	s3c24xx_init_uartdevs("s5pv210-uart", s5p_uart_resources, cfg, no);
 }

arch/arm/mach-s5pv210/setup-sdhci.c

-/* linux/arch/arm/mach-s5pv210/setup-sdhci.c
- *
- * Copyright (c) 2009-2010 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com/
- *
- * S5PV210 - Helper functions for settign up SDHCI device(s) (HSMMC)
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/types.h>
-
-/* clock sources for the mmc bus clock, order as for the ctrl2[5..4] */
-
-char *s5pv210_hsmmc_clksrcs[4] = {
-	[0] = "hsmmc",		/* HCLK */
-	/* [1] = "hsmmc",	- duplicate HCLK entry */
-	[2] = "sclk_mmc",	/* mmc_bus */
-	/* [3] = NULL,		- reserved */
-};

arch/arm/mach-s5pv210/setup-spi.c

+/* linux/arch/arm/mach-s5pv210/setup-spi.c
+ *
+ * Copyright (C) 2011 Samsung Electronics Ltd.
+ *		http://www.samsung.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+
+#include <plat/gpio-cfg.h>
+#include <plat/s3c64xx-spi.h>
+
+#ifdef CONFIG_S3C64XX_DEV_SPI0
+struct s3c64xx_spi_info s3c64xx_spi0_pdata = {
+	.fifo_lvl_mask	= 0x1ff,
+	.rx_lvl_offset	= 15,
+	.high_speed	= 1,
+	.tx_st_done	= 25,
+};
+
+int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
+{
+	s3c_gpio_cfgpin(S5PV210_GPB(0), S3C_GPIO_SFN(2));
+	s3c_gpio_setpull(S5PV210_GPB(0), S3C_GPIO_PULL_UP);
+	s3c_gpio_cfgall_range(S5PV210_GPB(2), 2,
+				S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_S3C64XX_DEV_SPI1
+struct s3c64xx_spi_info s3c64xx_spi1_pdata = {
+	.fifo_lvl_mask	= 0x7f,
+	.rx_lvl_offset	= 15,
+	.high_speed	= 1,
+	.tx_st_done	= 25,
+};
+
+int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
+{
+	s3c_gpio_cfgpin(S5PV210_GPB(4), S3C_GPIO_SFN(2));
+	s3c_gpio_setpull(S5PV210_GPB(4), S3C_GPIO_PULL_UP);
+	s3c_gpio_cfgall_range(S5PV210_GPB(6), 2,
+				S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
+	return 0;
+}
+#endif

arch/arm/plat-samsung/include/plat/dma-ops.h

@@ -31,6 +31,7 @@ struct samsung_dma_info {
 	enum dma_slave_buswidth width;
 	dma_addr_t fifo;
 	struct s3c2410_dma_client *client;
+	struct property *dt_dmach_prop;
 };
 
 struct samsung_dma_ops {