Commit c245d94e authored by Rayagonda Kokatanur's avatar Rayagonda Kokatanur Committed by Wolfram Sang

i2c: iproc: Add multi byte read-write support for slave mode

Add multiple byte read-write support for slave mode.
Signed-off-by: default avatarRayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: default avatarSrinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: default avatarRay Jui <ray.jui@broadcom.com>
Signed-off-by: default avatarWolfram Sang <wsa@the-dreams.de>
parent a4b5363a
......@@ -165,12 +165,6 @@ enum i2c_slave_read_status {
I2C_SLAVE_RX_END,
};
enum i2c_slave_xfer_dir {
I2C_SLAVE_DIR_READ = 0,
I2C_SLAVE_DIR_WRITE,
I2C_SLAVE_DIR_NONE,
};
enum bus_speed_index {
I2C_SPD_100K = 0,
I2C_SPD_400K,
......@@ -203,7 +197,6 @@ struct bcm_iproc_i2c_dev {
struct i2c_msg *msg;
struct i2c_client *slave;
enum i2c_slave_xfer_dir xfer_dir;
/* bytes that have been transferred */
unsigned int tx_bytes;
......@@ -219,7 +212,8 @@ struct bcm_iproc_i2c_dev {
| BIT(IS_M_RX_THLD_SHIFT))
#define ISR_MASK_SLAVE (BIT(IS_S_START_BUSY_SHIFT)\
| BIT(IS_S_RX_EVENT_SHIFT) | BIT(IS_S_RD_EVENT_SHIFT))
| BIT(IS_S_RX_EVENT_SHIFT) | BIT(IS_S_RD_EVENT_SHIFT)\
| BIT(IS_S_TX_UNDERRUN_SHIFT))
static int bcm_iproc_i2c_reg_slave(struct i2c_client *slave);
static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave);
......@@ -297,15 +291,11 @@ static void bcm_iproc_i2c_slave_init(
/* clear all pending slave interrupts */
iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, ISR_MASK_SLAVE);
/* Enable interrupt register for any READ event */
val = BIT(IE_S_RD_EVENT_SHIFT);
/* Enable interrupt register to indicate a valid byte in receive fifo */
val |= BIT(IE_S_RX_EVENT_SHIFT);
val = BIT(IE_S_RX_EVENT_SHIFT);
/* Enable interrupt register for the Slave BUSY command */
val |= BIT(IE_S_START_BUSY_SHIFT);
iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val);
iproc_i2c->xfer_dir = I2C_SLAVE_DIR_NONE;
}
static void bcm_iproc_i2c_check_slave_status(
......@@ -314,8 +304,11 @@ static void bcm_iproc_i2c_check_slave_status(
u32 val;
val = iproc_i2c_rd_reg(iproc_i2c, S_CMD_OFFSET);
val = (val >> S_CMD_STATUS_SHIFT) & S_CMD_STATUS_MASK;
/* status is valid only when START_BUSY is cleared after it was set */
if (val & BIT(S_CMD_START_BUSY_SHIFT))
return;
val = (val >> S_CMD_STATUS_SHIFT) & S_CMD_STATUS_MASK;
if (val == S_CMD_STATUS_TIMEOUT) {
dev_err(iproc_i2c->device, "slave random stretch time timeout\n");
......@@ -329,68 +322,64 @@ static void bcm_iproc_i2c_check_slave_status(
static bool bcm_iproc_i2c_slave_isr(struct bcm_iproc_i2c_dev *iproc_i2c,
u32 status)
{
u8 value;
u32 val;
u32 rd_status;
u32 tmp;
u8 value, rx_status;
/* Start of transaction. check address and populate the direction */
if (iproc_i2c->xfer_dir == I2C_SLAVE_DIR_NONE) {
tmp = iproc_i2c_rd_reg(iproc_i2c, S_RX_OFFSET);
rd_status = (tmp >> S_RX_STATUS_SHIFT) & S_RX_STATUS_MASK;
/* This condition checks whether the request is a new request */
if (((rd_status == I2C_SLAVE_RX_START) &&
(status & BIT(IS_S_RX_EVENT_SHIFT))) ||
((rd_status == I2C_SLAVE_RX_END) &&
(status & BIT(IS_S_RD_EVENT_SHIFT)))) {
/* Last bit is W/R bit.
* If 1 then its a read request(by master).
*/
iproc_i2c->xfer_dir = tmp & SLAVE_READ_WRITE_BIT_MASK;
if (iproc_i2c->xfer_dir == I2C_SLAVE_DIR_WRITE)
i2c_slave_event(iproc_i2c->slave,
I2C_SLAVE_READ_REQUESTED, &value);
else
/* Slave RX byte receive */
if (status & BIT(IS_S_RX_EVENT_SHIFT)) {
val = iproc_i2c_rd_reg(iproc_i2c, S_RX_OFFSET);
rx_status = (val >> S_RX_STATUS_SHIFT) & S_RX_STATUS_MASK;
if (rx_status == I2C_SLAVE_RX_START) {
/* Start of SMBUS for Master write */
i2c_slave_event(iproc_i2c->slave,
I2C_SLAVE_WRITE_REQUESTED, &value);
}
}
/* read request from master */
if ((status & BIT(IS_S_RD_EVENT_SHIFT)) &&
(iproc_i2c->xfer_dir == I2C_SLAVE_DIR_WRITE)) {
val = iproc_i2c_rd_reg(iproc_i2c, S_RX_OFFSET);
value = (u8)((val >> S_RX_DATA_SHIFT) & S_RX_DATA_MASK);
i2c_slave_event(iproc_i2c->slave,
I2C_SLAVE_READ_PROCESSED, &value);
I2C_SLAVE_WRITE_RECEIVED, &value);
} else if (status & BIT(IS_S_RD_EVENT_SHIFT)) {
/* Start of SMBUS for Master Read */
i2c_slave_event(iproc_i2c->slave,
I2C_SLAVE_READ_REQUESTED, &value);
iproc_i2c_wr_reg(iproc_i2c, S_TX_OFFSET, value);
val = BIT(S_CMD_START_BUSY_SHIFT);
iproc_i2c_wr_reg(iproc_i2c, S_CMD_OFFSET, val);
}
/* write request from master */
if ((status & BIT(IS_S_RX_EVENT_SHIFT)) &&
(iproc_i2c->xfer_dir == I2C_SLAVE_DIR_READ)) {
val = iproc_i2c_rd_reg(iproc_i2c, S_RX_OFFSET);
/* Its a write request by Master to Slave.
* We read data present in receive FIFO
/*
* Enable interrupt for TX FIFO becomes empty and
* less than PKT_LENGTH bytes were output on the SMBUS
*/
val = iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
val |= BIT(IE_S_TX_UNDERRUN_SHIFT);
iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val);
} else {
/* Master write other than start */
value = (u8)((val >> S_RX_DATA_SHIFT) & S_RX_DATA_MASK);
i2c_slave_event(iproc_i2c->slave,
I2C_SLAVE_WRITE_RECEIVED, &value);
}
} else if (status & BIT(IS_S_TX_UNDERRUN_SHIFT)) {
/* Master read other than start */
i2c_slave_event(iproc_i2c->slave,
I2C_SLAVE_READ_PROCESSED, &value);
/* check the status for the last byte of the transaction */
rd_status = (val >> S_RX_STATUS_SHIFT) & S_RX_STATUS_MASK;
if (rd_status == I2C_SLAVE_RX_END)
iproc_i2c->xfer_dir = I2C_SLAVE_DIR_NONE;
dev_dbg(iproc_i2c->device, "\nread value = 0x%x\n", value);
iproc_i2c_wr_reg(iproc_i2c, S_TX_OFFSET, value);
val = BIT(S_CMD_START_BUSY_SHIFT);
iproc_i2c_wr_reg(iproc_i2c, S_CMD_OFFSET, val);
}
/* Stop */
if (status & BIT(IS_S_START_BUSY_SHIFT)) {
i2c_slave_event(iproc_i2c->slave, I2C_SLAVE_STOP, &value);
iproc_i2c->xfer_dir = I2C_SLAVE_DIR_NONE;
/*
* Enable interrupt for TX FIFO becomes empty and
* less than PKT_LENGTH bytes were output on the SMBUS
*/
val = iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
val &= ~BIT(IE_S_TX_UNDERRUN_SHIFT);
iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val);
}
/* clear interrupt status */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment