Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM 64-bit DT updates from Arnd Bergmann: "ARM64 DT updates are fairly small this time, only two new SoCs and a handful of new machines get added, all of them similar to other hardware we already support. New SoC: - HiSilicon Kirin960/Hi3660 and HiKey960 development board - NXP LS1012a with three reference boards: http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A New development board: - Banana Pi M64, based on Allwinner A64: http://www.banana-pi.org/m64.html - SolidRun MACCHIATOBin based on Marvell Armada 8K: https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/ - Broadcom BCM958712DxXMC NorthStar2 reference board (another one) A lot of platforms improve support for existing machines by adding extra devices for which a binding and driver is availabe: Allwinner: - MMC, USB ARM Juno: - Coresight, STM Broadcom: - NS2 GICv2m irqchip and PCIe Marvell: - Armada 3700 SPI, I2C, ethernet switch Mediatek: - MT8173 thermal NXP i.MX: - LS1046A thermal Qualcomm: - coresight on MSM8916, HDMI, WCNSS, SCM Renesas: - r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd Rockchip: - thermal, eDP, pinctrl enhancements Samsung: - TM2 touchkey, Exynos5433 HDMI and power management improvements UniPhier: - SD reset, eMMC controller ZTE: - oppv2 cpufreq" * tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (110 commits) arm64: dts: qcom: Add msm8916 CoreSight components arm64: dts: marvell: adjust name of sd-mmc-gop clock in syscon arm64: allwinner: add BananaPi-M64 support arm64: allwinner: a64: add UART1 pin nodes arm64: allwinner: pine64: add MMC support arm64: allwinner: a64: Increase the MMC max frequency arm64: allwinner: a64: Add MMC pinctrl nodes arm64: allwinner: a64: Add MMC nodes dt-bindings: clockgen: Add compatible string for LS1012A Documentation: DT: add LS1012A compatible for SCFG and DCFG Documentation: DT: Add entry for FSL LS1012A RDB, FRDM, QDS boards arm64: dts: marvell: add generic-ahci compatibles for CP110 ahci arm64: tegra: Use symbolic reset identifiers arm64: dts: r8a7796: Mark EthernetAVB device node disabled arm64: dts: r8a7795: Mark EthernetAVB device node disabled arm64: dts: r8a7795: tidyup audma definition order arm64: dts: r8a7796: Link ARM GIC to clock and clock domain arm64: dts: r8a7795: Link ARM GIC to clock and clock domain arm64: dts: r8a7796: Add R-Car Gen3 thermal support arm64: dts: r8a7795: Add R-Car Gen3 thermal support ...

Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann: "ARM64 DT updates are fairly small this time, only two new SoCs and a handful of new machines get added, all of them similar to other hardware we already support. New SoC: - HiSilicon Kirin960/Hi3660 and HiKey960 development board - NXP LS1012a with three reference boards: http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A New development board: - Banana Pi M64, based on Allwinner A64: http://www.banana-pi.org/m64.html - SolidRun MACCHIATOBin based on Marvell Armada 8K: https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/ - Broadcom BCM958712DxXMC NorthStar2 reference board (another one) A lot of platforms improve support for existing machines by adding extra devices for which a binding and driver is availabe: Allwinner: - MMC, USB ARM Juno: - Coresight, STM Broadcom: - NS2 GICv2m irqchip and PCIe Marvell: - Armada 3700 SPI, I2C, ethernet switch Mediatek: - MT8173 thermal NXP i.MX: - LS1046A thermal Qualcomm: - coresight on MSM8916, HDMI, WCNSS, SCM Renesas: - r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd Rockchip: - thermal, eDP, pinctrl enhancements Samsung: - TM2 touchkey, Exynos5433 HDMI and power management improvements UniPhier: - SD reset, eMMC controller ZTE: - oppv2 cpufreq" * tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (110 commits) arm64: dts: qcom: Add msm8916 CoreSight components arm64: dts: marvell: adjust name of sd-mmc-gop clock in syscon arm64: allwinner: add BananaPi-M64 support arm64: allwinner: a64: add UART1 pin nodes arm64: allwinner: pine64: add MMC support arm64: allwinner: a64: Increase the MMC max frequency arm64: allwinner: a64: Add MMC pinctrl nodes arm64: allwinner: a64: Add MMC nodes dt-bindings: clockgen: Add compatible string for LS1012A Documentation: DT: add LS1012A compatible for SCFG and DCFG Documentation: DT: Add entry for FSL LS1012A RDB, FRDM, QDS boards arm64: dts: marvell: add generic-ahci compatibles for CP110 ahci arm64: tegra: Use symbolic reset identifiers arm64: dts: r8a7796: Mark EthernetAVB device node disabled arm64: dts: r8a7795: Mark EthernetAVB device node disabled arm64: dts: r8a7795: tidyup audma definition order arm64: dts: r8a7796: Link ARM GIC to clock and clock domain arm64: dts: r8a7795: Link ARM GIC to clock and clock domain arm64: dts: r8a7796: Add R-Car Gen3 thermal support arm64: dts: r8a7795: Add R-Car Gen3 thermal support ...
c61c15e0 · Linus Torvalds · 195849ea · cbab3197 · c61c15e0 · c61c15e0
Commit c61c15e0 authored Feb 23, 2017 by Linus Torvalds
72 changed files
--- a/Documentation/devicetree/bindings/arm/cpus.txt
+++ b/Documentation/devicetree/bindings/arm/cpus.txt
@@ -158,6 +158,7 @@ nodes to be present and contain the properties described below.
 			    "arm,cortex-a53"
 			    "arm,cortex-a57"
 			    "arm,cortex-a72"
+			    "arm,cortex-a73"
 			    "arm,cortex-m0"
 			    "arm,cortex-m0+"
 			    "arm,cortex-m1"

--- a/Documentation/devicetree/bindings/arm/fsl.txt
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@@ -108,7 +108,7 @@ status.
  - compatible: Should contain a chip-specific compatible string,
 	Chip-specific strings are of the form "fsl,<chip>-scfg",
 	The following <chip>s are known to be supported:
-	ls1021a, ls1043a, ls1046a, ls2080a.
+	ls1012a, ls1021a, ls1043a, ls1046a, ls2080a.

  - reg: should contain base address and length of SCFG memory-mapped registers

@@ -126,7 +126,7 @@ core start address and release the secondary core from holdoff and startup.
  - compatible: Should contain a chip-specific compatible string,
 	Chip-specific strings are of the form "fsl,<chip>-dcfg",
 	The following <chip>s are known to be supported:
-	ls1021a, ls1043a, ls1046a, ls2080a.
+	ls1012a, ls1021a, ls1043a, ls1046a, ls2080a.

  - reg : should contain base address and length of DCFG memory-mapped registers

@@ -139,6 +139,22 @@ Example:
 Freescale ARMv8 based Layerscape SoC family Device Tree Bindings
 ----------------------------------------------------------------

+LS1012A SoC
+Required root node properties:
+    - compatible = "fsl,ls1012a";
+
+LS1012A ARMv8 based RDB Board
+Required root node properties:
+    - compatible = "fsl,ls1012a-rdb", "fsl,ls1012a";
+
+LS1012A ARMv8 based FRDM Board
+Required root node properties:
+    - compatible = "fsl,ls1012a-frdm", "fsl,ls1012a";
+
+LS1012A ARMv8 based QDS Board
+Required root node properties:
+    - compatible = "fsl,ls1012a-qds", "fsl,ls1012a";
+
 LS1043A SoC
 Required root node properties:
    - compatible = "fsl,ls1043a";

--- a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
+++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
 Hisilicon Platforms Device Tree Bindings
 ----------------------------------------------------
+Hi3660 SoC
+Required root node properties:
+	- compatible = "hisilicon,hi3660";
+
 Hi4511 Board
 Required root node properties:
 	- compatible = "hisilicon,hi3620-hi4511";

--- a/Documentation/devicetree/bindings/arm/shmobile.txt
+++ b/Documentation/devicetree/bindings/arm/shmobile.txt
@@ -75,7 +75,7 @@ Boards:
    compatible = "renesas,rskrza1", "renesas,r7s72100"
  - Salvator-X (RTP0RC7795SIPB0010S)
    compatible = "renesas,salvator-x", "renesas,r8a7795";
-  - Salvator-X
+  - Salvator-X (RTP0RC7796SIPB0011S)
    compatible = "renesas,salvator-x", "renesas,r8a7796";
  - SILK (RTP0RC7794LCB00011S)
    compatible = "renesas,silk", "renesas,r8a7794"

--- a/Documentation/devicetree/bindings/clock/qoriq-clock.txt
+++ b/Documentation/devicetree/bindings/clock/qoriq-clock.txt
@@ -31,6 +31,7 @@ Required properties:
 	* "fsl,t4240-clockgen"
 	* "fsl,b4420-clockgen"
 	* "fsl,b4860-clockgen"
+	* "fsl,ls1012a-clockgen"
 	* "fsl,ls1021a-clockgen"
 	* "fsl,ls1043a-clockgen"
 	* "fsl,ls1046a-clockgen"

--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-bananapi-m64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb

 always		:= $(dtb-y)

--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+/*
+ * Copyright (c) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "sun50i-a64.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "BananaPi-M64";
+	compatible = "sinovoip,bananapi-m64", "allwinner,sun50i-a64";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_vcc3v3: vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	status = "okay";
+};
+
+&i2c1_pins {
+	bias-pull-up;
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	status = "okay";
+};
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
@@ -44,6 +44,8 @@

 #include "sun50i-a64.dtsi"

+#include <dt-bindings/gpio/gpio.h>
+
 / {
 	model = "Pine64";
 	compatible = "pine64,pine64", "allwinner,sun50i-a64";
@@ -55,11 +57,16 @@ aliases {
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	reg_vcc3v3: vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 };

-&uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+&ehci1 {
 	status = "okay";
 };

@@ -72,3 +79,33 @@ &i2c1 {
 &i2c1_pins {
 	bias-pull-up;
 };
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
@@ -42,8 +42,9 @@
 *     OTHER DEALINGS IN THE SOFTWARE.
 */

+#include <dt-bindings/clock/sun50i-a64-ccu.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/reset/sun50i-a64-ccu.h>

 / {
 	interrupt-parent = <&gic>;
@@ -120,6 +121,105 @@ soc {
 		#size-cells = <1>;
 		ranges;

+		mmc0: mmc@1c0f000 {
+			compatible = "allwinner,sun50i-a64-mmc";
+			reg = <0x01c0f000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC0>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			max-frequency = <150000000>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc1: mmc@1c10000 {
+			compatible = "allwinner,sun50i-a64-mmc";
+			reg = <0x01c10000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC1>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			max-frequency = <150000000>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc2: mmc@1c11000 {
+			compatible = "allwinner,sun50i-a64-emmc";
+			reg = <0x01c11000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC2>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			max-frequency = <200000000>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		usb_otg: usb@01c19000 {
+			compatible = "allwinner,sun8i-a33-musb";
+			reg = <0x01c19000 0x0400>;
+			clocks = <&ccu CLK_BUS_OTG>;
+			resets = <&ccu RST_BUS_OTG>;
+			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "mc";
+			phys = <&usbphy 0>;
+			phy-names = "usb";
+			extcon = <&usbphy 0>;
+			status = "disabled";
+		};
+
+		usbphy: phy@01c19400 {
+			compatible = "allwinner,sun50i-a64-usb-phy";
+			reg = <0x01c19400 0x14>,
+			      <0x01c1b800 0x4>;
+			reg-names = "phy_ctrl",
+				    "pmu1";
+			clocks = <&ccu CLK_USB_PHY0>,
+				 <&ccu CLK_USB_PHY1>;
+			clock-names = "usb0_phy",
+				      "usb1_phy";
+			resets = <&ccu RST_USB_PHY0>,
+				 <&ccu RST_USB_PHY1>;
+			reset-names = "usb0_reset",
+				      "usb1_reset";
+			status = "disabled";
+			#phy-cells = <1>;
+		};
+
+		ehci1: usb@01c1b000 {
+			compatible = "allwinner,sun50i-a64-ehci", "generic-ehci";
+			reg = <0x01c1b000 0x100>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_OHCI1>,
+				 <&ccu CLK_BUS_EHCI1>,
+				 <&ccu CLK_USB_OHCI1>;
+			resets = <&ccu RST_BUS_OHCI1>,
+				 <&ccu RST_BUS_EHCI1>;
+			phys = <&usbphy 1>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		ohci1: usb@01c1b400 {
+			compatible = "allwinner,sun50i-a64-ohci", "generic-ohci";
+			reg = <0x01c1b400 0x100>;
+			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_OHCI1>,
+				 <&ccu CLK_USB_OHCI1>;
+			resets = <&ccu RST_BUS_OHCI1>;
+			phys = <&usbphy 1>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
 		ccu: clock@01c20000 {
 			compatible = "allwinner,sun50i-a64-ccu";
 			reg = <0x01c20000 0x400>;
@@ -146,10 +246,45 @@ i2c1_pins: i2c1_pins {
 				function = "i2c1";
 			};

+			mmc0_pins: mmc0-pins {
+				pins = "PF0", "PF1", "PF2", "PF3",
+				       "PF4", "PF5";
+				function = "mmc0";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			mmc1_pins: mmc1-pins {
+				pins = "PG0", "PG1", "PG2", "PG3",
+				       "PG4", "PG5";
+				function = "mmc1";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			mmc2_pins: mmc2-pins {
+				pins = "PC1", "PC5", "PC6", "PC8", "PC9",
+				       "PC10","PC11", "PC12", "PC13",
+				       "PC14", "PC15", "PC16";
+				function = "mmc2";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
 			uart0_pins_a: uart0@0 {
 				pins = "PB8", "PB9";
 				function = "uart0";
 			};
+
+			uart1_pins: uart1_pins {
+				pins = "PG6", "PG7";
+				function = "uart1";
+			};
+
+			uart1_rts_cts_pins: uart1_rts_cts_pins {
+				pins = "PG8", "PG9";
+				function = "uart1";
+			};
 		};

 		uart0: serial@1c28000 {

--- a/arch/arm64/boot/dts/arm/juno-base.dtsi
+++ b/arch/arm64/boot/dts/arm/juno-base.dtsi
+#include "juno-clocks.dtsi"
+
+/ {
 	/*
 	 *  Devices shared by all Juno boards
 	 */
+	dma-ranges = <0 0 0 0 0x100 0>;

 	memtimer: timer@2a810000 {
 		compatible = "arm,armv7-timer-mem";
@@ -48,6 +52,7 @@ smmu_etr: iommu@2b600000 {
 		#iommu-cells = <1>;
 		#global-interrupts = <1>;
 		dma-coherent;
+		power-domains = <&scpi_devpd 0>;
 		status = "disabled";
 	};

@@ -83,7 +88,7 @@ timer {
 	 * The actual size is just 4K though 64K is reserved. Access to the
 	 * unmapped reserved region results in a DECERR response.
 	 */
-	etf@20010000 {
+	etf@20010000 { /* etf0 */
 		compatible = "arm,coresight-tmc", "arm,primecell";
 		reg = <0 0x20010000 0 0x1000>;

@@ -97,7 +102,7 @@ ports {
 			/* input port */
 			port@0 {
 				reg = <0>;
-				etf_in_port: endpoint {
+				etf0_in_port: endpoint {
 					slave-mode;
 					remote-endpoint = <&main_funnel_out_port>;
 				};
@@ -106,8 +111,7 @@ etf_in_port: endpoint {
 			/* output port */
 			port@1 {
 				reg = <0>;
-				etf_out_port: endpoint {
-					remote-endpoint = <&replicator_in_port0>;
+				etf0_out_port: endpoint {
 				};
 			};
 		};
@@ -128,7 +132,8 @@ tpiu_in_port: endpoint {
 		};
 	};

-	main-funnel@20040000 {
+	/* main funnel on Juno r0, cssys0 funnel on Juno r1/r2 as per TRM*/
+	main_funnel: funnel@20040000 {
 		compatible = "arm,coresight-funnel", "arm,primecell";
 		reg = <0 0x20040000 0 0x1000>;

@@ -139,13 +144,15 @@ ports {
 			#address-cells = <1>;
 			#size-cells = <0>;

+			/* output port */
 			port@0 {
 				reg = <0>;
 				main_funnel_out_port: endpoint {
-					remote-endpoint = <&etf_in_port>;
+					remote-endpoint = <&etf0_in_port>;
 				};
 			};

+			/* input ports */
 			port@1 {
 				reg = <0>;
 				main_funnel_in_port0: endpoint {
@@ -161,7 +168,6 @@ main_funnel_in_port1: endpoint {
 					remote-endpoint = <&cluster1_funnel_out_port>;
 				};
 			};
-
 		};
 	};

@@ -181,6 +187,21 @@ etr_in_port: endpoint {
 		};
 	};

+	stm@20100000 {
+		compatible = "arm,coresight-stm", "arm,primecell";
+		reg = <0 0x20100000 0 0x1000>,
+		      <0 0x28000000 0 0x1000000>;
+		reg-names = "stm-base", "stm-stimulus-base";
+
+		clocks = <&soc_smc50mhz>;
+		clock-names = "apb_pclk";
+		power-domains = <&scpi_devpd 0>;
+		port {
+			stm_out_port: endpoint {
+			};
+		};
+	};
+
 	etm0: etm@22040000 {
 		compatible = "arm,coresight-etm4x", "arm,primecell";
 		reg = <0 0x22040000 0 0x1000>;
@@ -195,7 +216,7 @@ cluster0_etm0_out_port: endpoint {
 		};
 	};

-	cluster0-funnel@220c0000 {
+	funnel@220c0000 { /* cluster0 funnel */
 		compatible = "arm,coresight-funnel", "arm,primecell";
 		reg = <0 0x220c0000 0 0x1000>;

@@ -259,7 +280,7 @@ cluster1_etm0_out_port: endpoint {
 		};
 	};

-	cluster1-funnel@230c0000 {
+	funnel@230c0000 { /* cluster1 funnel */
 		compatible = "arm,coresight-funnel", "arm,primecell";
 		reg = <0 0x230c0000 0 0x1000>;

@@ -382,7 +403,6 @@ port@2 {
 				reg = <0>;
 				replicator_in_port0: endpoint {
 					slave-mode;
-					remote-endpoint = <&etf_out_port>;
 				};
 			};
 		};
@@ -507,8 +527,6 @@ gpu1_thermal_zone: gpu1 {
 		};
 	};

-	/include/ "juno-clocks.dtsi"
-
 	smmu_dma: iommu@7fb00000 {
 		compatible = "arm,mmu-401", "arm,smmu-v1";
 		reg = <0x0 0x7fb00000 0x0 0x10000>;
@@ -719,3 +737,4 @@ site2: tlx@60000000 {
 		interrupt-map-mask = <0 0>;
 		interrupt-map = <0 0 &gic 0 0 0 168 IRQ_TYPE_LEVEL_HIGH>;
 	};
+};
--- a/arch/arm64/boot/dts/arm/juno-clocks.dtsi
+++ b/arch/arm64/boot/dts/arm/juno-clocks.dtsi
@@ -6,7 +6,7 @@
 * This file is licensed under a dual GPLv2 or BSD license.
 *
 */
-
+/ {
 	/* SoC fixed clocks */
 	soc_uartclk: refclk7273800hz {
 		compatible = "fixed-clock";
@@ -42,3 +42,4 @@ soc_faxiclk: refclk400mhz {
 		clock-frequency = <400000000>;
 		clock-output-names = "faxi_clk";
 	};
+};
--- a/arch/arm64/boot/dts/arm/juno-cs-r1r2.dtsi
+++ b/arch/arm64/boot/dts/arm/juno-cs-r1r2.dtsi
+/ {
+	funnel@20130000 { /* cssys1 */
+		compatible = "arm,coresight-funnel", "arm,primecell";
+		reg = <0 0x20130000 0 0x1000>;
+
+		clocks = <&soc_smc50mhz>;
+		clock-names = "apb_pclk";
+		power-domains = <&scpi_devpd 0>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* output port */
+			port@0 {
+				reg = <0>;
+				csys1_funnel_out_port: endpoint {
+					remote-endpoint = <&etf1_in_port>;
+				};
+			};
+
+			/* input port */
+			port@1 {
+				reg = <0>;
+				csys1_funnel_in_port0: endpoint {
+					slave-mode;
+				};
+			};
+
+		};
+	};
+
+	etf@20140000 { /* etf1 */
+		compatible = "arm,coresight-tmc", "arm,primecell";
+		reg = <0 0x20140000 0 0x1000>;
+
+		clocks = <&soc_smc50mhz>;
+		clock-names = "apb_pclk";
+		power-domains = <&scpi_devpd 0>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* input port */
+			port@0 {
+				reg = <0>;
+				etf1_in_port: endpoint {
+					slave-mode;
+					remote-endpoint = <&csys1_funnel_out_port>;
+				};
+			};
+
+			/* output port */
+			port@1 {
+				reg = <0>;
+				etf1_out_port: endpoint {
+					remote-endpoint = <&csys2_funnel_in_port1>;
+				};
+			};
+		};
+	};
+
+	funnel@20150000 { /* cssys2 */
+		compatible = "arm,coresight-funnel", "arm,primecell";
+		reg = <0 0x20150000 0 0x1000>;
+
+		clocks = <&soc_smc50mhz>;
+		clock-names = "apb_pclk";
+		power-domains = <&scpi_devpd 0>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* output port */
+			port@0 {
+				reg = <0>;
+				csys2_funnel_out_port: endpoint {
+					remote-endpoint = <&replicator_in_port0>;
+				};
+			};
+
+			/* input ports */
+			port@1 {
+				reg = <0>;
+				csys2_funnel_in_port0: endpoint {
+					slave-mode;
+					remote-endpoint = <&etf0_out_port>;
+				};
+			};
+
+			port@2 {
+				reg = <1>;
+				csys2_funnel_in_port1: endpoint {
+					slave-mode;
+					remote-endpoint = <&etf1_out_port>;
+				};
+			};
+
+		};
+	};
+};
--- a/arch/arm64/boot/dts/arm/juno-motherboard.dtsi
+++ b/arch/arm64/boot/dts/arm/juno-motherboard.dtsi
@@ -131,13 +131,6 @@ ethernet@2,00000000 {
 				vddvario-supply = <&mb_fixed_3v3>;
 			};

-			usb@5,00000000 {
-				compatible = "nxp,usb-isp1763";
-				reg = <5 0x00000000 0x20000>;
-				bus-width = <16>;
-				interrupts = <4>;
-			};
-
 			iofpga@3,00000000 {
 				compatible = "simple-bus";
 				#address-cells = <1>;

--- a/arch/arm64/boot/dts/arm/juno-r1.dts
+++ b/arch/arm64/boot/dts/arm/juno-r1.dts
@@ -9,6 +9,8 @@
 /dts-v1/;

 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "juno-base.dtsi"
+#include "juno-cs-r1r2.dtsi"

 / {
 	model = "ARM Juno development board (r1)";
@@ -176,8 +178,6 @@ pmu_a53 {
 				     <&A53_2>,
 				     <&A53_3>;
 	};
-
-	#include "juno-base.dtsi"
 };

 &memtimer {
@@ -227,3 +227,15 @@ &gpu0_thermal_zone {
 &gpu1_thermal_zone {
 	status = "okay";
 };
+
+&etf0_out_port {
+	remote-endpoint = <&csys2_funnel_in_port0>;
+};
+
+&replicator_in_port0 {
+	remote-endpoint = <&csys2_funnel_out_port>;
+};
+
+&stm_out_port {
+	remote-endpoint = <&csys1_funnel_in_port0>;
+};
--- a/arch/arm64/boot/dts/arm/juno-r2.dts
+++ b/arch/arm64/boot/dts/arm/juno-r2.dts
@@ -9,6 +9,8 @@
 /dts-v1/;

 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "juno-base.dtsi"
+#include "juno-cs-r1r2.dtsi"

 / {
 	model = "ARM Juno development board (r2)";
@@ -176,8 +178,6 @@ pmu_a53 {
 				     <&A53_2>,
 				     <&A53_3>;
 	};
-
-	#include "juno-base.dtsi"
 };

 &memtimer {
@@ -227,3 +227,15 @@ &gpu0_thermal_zone {
 &gpu1_thermal_zone {
 	status = "okay";
 };
+
+&etf0_out_port {
+	remote-endpoint = <&csys2_funnel_in_port0>;
+};
+
+&replicator_in_port0 {
+	remote-endpoint = <&csys2_funnel_out_port>;
+};
+
+&stm_out_port {
+	remote-endpoint = <&csys1_funnel_in_port0>;
+};
--- a/arch/arm64/boot/dts/arm/juno.dts
+++ b/arch/arm64/boot/dts/arm/juno.dts
@@ -9,6 +9,7 @@
 /dts-v1/;

 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "juno-base.dtsi"

 / {
 	model = "ARM Juno development board (r0)";
@@ -176,8 +177,6 @@ pmu_a53 {
 				     <&A53_2>,
 				     <&A53_3>;
 	};
-
-	#include "juno-base.dtsi"
 };

 &etm0 {
@@ -203,3 +202,27 @@ &etm4 {
 &etm5 {
 	cpu = <&A53_3>;
 };
+
+&etf0_out_port {
+	remote-endpoint = <&replicator_in_port0>;
+};
+
+&replicator_in_port0 {
+	remote-endpoint = <&etf0_out_port>;
+};
+
+&stm_out_port {
+	remote-endpoint = <&main_funnel_in_port2>;
+};
+
+&main_funnel {
+	ports {
+		port@3 {
+			reg = <2>;
+			main_funnel_in_port2: endpoint {
+				slave-mode;
+				remote-endpoint = <&stm_out_port>;
+			};
+		};
+	};
+};
--- a/arch/arm64/boot/dts/broadcom/Makefile
+++ b/arch/arm64/boot/dts/broadcom/Makefile
 dtb-$(CONFIG_ARCH_BCM2835) += bcm2837-rpi-3-b.dtb
-dtb-$(CONFIG_ARCH_BCM_IPROC) += ns2-svk.dtb
+dtb-$(CONFIG_ARCH_BCM_IPROC) += ns2-svk.dtb ns2-xmc.dtb
 dtb-$(CONFIG_ARCH_VULCAN) += vulcan-eval.dtb

 always		:= $(dtb-y)

--- a/arch/arm64/boot/dts/broadcom/ns2-svk.dts
+++ b/arch/arm64/boot/dts/broadcom/ns2-svk.dts
@@ -76,6 +76,10 @@ &pcie4 {
 	status = "ok";
 };

+&pcie8 {
+	status = "ok";
+};
+
 &i2c0 {
 	status = "ok";
 };

--- a/arch/arm64/boot/dts/broadcom/ns2-xmc.dts
+++ b/arch/arm64/boot/dts/broadcom/ns2-xmc.dts
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2016 Broadcom.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "ns2.dtsi"
+
+/ {
+	model = "Broadcom NS2 XMC";
+	compatible = "brcm,ns2-xmc", "brcm,ns2";
+
+	aliases {
+		serial0 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+		bootargs = "earlycon=uart8250,mmio32,0x66130000";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x000000000 0x80000000 0x00000001 0x00000000>;
+	};
+};
+
+&enet {
+	status = "ok";
+};
+
+&i2c0 {
+	status = "ok";
+};
+
+&i2c1 {
+	status = "ok";
+};
+
+&mdio_mux_iproc {
+	mdio@10 {
+		gphy0: eth-phy@10 {
+			reg = <0x10>;
+		};
+	};
+};
+
+&nand {
+	nandcs@0 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-ecc-mode = "hw";
+		nand-ecc-strength = <8>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <16>;
+		brcm,nand-oob-sector-size = <16>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "nboot";
+			reg = <0x00000000 0x00280000>; /*  2.5MB */
+			read-only;
+		};
+
+		partition@280000 {
+			label = "nenv";
+			reg = <0x00280000 0x00040000>; /* 0.25MB */
+			read-only;
+		};
+
+		partition@2c0000 {
+			label = "ndtb";
+			reg = <0x002c0000 0x00040000>; /* 0.25MB */
+			read-only;
+		};
+
+		partition@300000 {
+			label = "nsystem";
+			reg = <0x00300000 0x03d00000>; /*   61MB */
+			read-only;
+		};
+
+		partition@4000000 {
+			label = "nrootfs";
+			reg = <0x04000000 0x06400000>; /*  100MB */
+		};
+
+		partition@0a400000{
+			label = "ncustfs";
+			reg = <0x0a400000 0x35c00000>; /*  860MB */
+		};
+	};
+};
+
+&pci_phy0 {
+	status = "ok";
+};
+
+&pcie0 {
+	status = "ok";
+};
+
+&pcie8 {
+	status = "ok";
+};
+
+&sata_phy0 {
+	status = "ok";
+};
+
+&sata_phy1 {
+	status = "ok";
+};
+
+&sata {
+	status = "ok";
+};
+
+&qspi {
+	flash: m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p80";
+		spi-max-frequency = <62500000>;
+		m25p,default-addr-width = <3>;
+		reg = <0x0 0x0>;
+
+		partition@0 {
+			label = "bl0";
+			reg = <0x00000000 0x00080000>; /*  512KB */
+		};
+
+		partition@80000 {
+			label = "fip";
+			reg = <0x00080000 0x00150000>; /* 1344KB */
+		};
+
+		partition@1e0000 {
+			label = "env";
+			reg = <0x001e0000 0x00010000>;/*    64KB */
+		};
+
+		partition@1f0000 {
+			label = "dtb";
+			reg = <0x001f0000 0x00010000>; /*   64KB */
+		};
+
+		partition@200000 {
+			label = "kernel";
+			reg = <0x00200000 0x00e00000>; /*   14MB */
+		};
+
+		partition@1000000 {
+			label = "rootfs";
+			reg = <0x01000000 0x01000000>; /*   16MB */
+		};
+	};
+};
+
+&uart3 {
+	status = "ok";
+};
--- a/arch/arm64/boot/dts/broadcom/ns2.dtsi
+++ b/arch/arm64/boot/dts/broadcom/ns2.dtsi
@@ -30,6 +30,8 @@
 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */

+/memreserve/ 0x81000000 0x00200000;
+
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/bcm-ns2.h>

@@ -115,7 +117,7 @@ pcie0: pcie@20020000 {

 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 281 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 281 IRQ_TYPE_NONE>;

 		linux,pci-domain = <0>;

@@ -136,18 +138,7 @@ pcie0: pcie@20020000 {
 		phys = <&pci_phy0>;
 		phy-names = "pcie-phy";

-		msi-parent = <&msi0>;
-		msi0: msi@20020000 {
-			compatible = "brcm,iproc-msi";
-			msi-controller;
-			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 277 IRQ_TYPE_NONE>,
-				     <GIC_SPI 278 IRQ_TYPE_NONE>,
-				     <GIC_SPI 279 IRQ_TYPE_NONE>,
-				     <GIC_SPI 280 IRQ_TYPE_NONE>;
-			brcm,num-eq-region = <1>;
-			brcm,num-msi-msg-region = <1>;
-		};
+		msi-parent = <&v2m0>;
 	};

 	pcie4: pcie@50020000 {
@@ -156,7 +147,7 @@ pcie4: pcie@50020000 {

 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 305 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 305 IRQ_TYPE_NONE>;

 		linux,pci-domain = <4>;

@@ -177,16 +168,24 @@ pcie4: pcie@50020000 {
 		phys = <&pci_phy1>;
 		phy-names = "pcie-phy";

-		msi-parent = <&msi4>;
-		msi4: msi@50020000 {
-			compatible = "brcm,iproc-msi";
-			msi-controller;
-			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 301 IRQ_TYPE_NONE>,
-				     <GIC_SPI 302 IRQ_TYPE_NONE>,
-				     <GIC_SPI 303 IRQ_TYPE_NONE>,
-				     <GIC_SPI 304 IRQ_TYPE_NONE>;
-		};
+		msi-parent = <&v2m0>;
+	};
+
+	pcie8: pcie@60c00000 {
+		compatible = "brcm,iproc-pcie-paxc";
+		reg = <0 0x60c00000 0 0x1000>;
+		linux,pci-domain = <8>;
+
+		bus-range = <0x0 0x1>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		ranges = <0x83000000 0 0x00000000 0 0x60000000 0 0x00c00000>;
+
+		status = "disabled";
+
+		msi-parent = <&v2m0>;
 	};

 	soc: soc {
@@ -331,6 +330,82 @@ gic: interrupt-controller@65210000 {
 			      <0x65260000 0x1000>;
 			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_RAW(0xf) |
 				      IRQ_TYPE_LEVEL_HIGH)>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x652e0000 0x80000>;
+
+			v2m0: v2m@00000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x00000 0x1000>;
+				arm,msi-base-spi = <72>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m1: v2m@10000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x10000 0x1000>;
+				arm,msi-base-spi = <88>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m2: v2m@20000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x20000 0x1000>;
+				arm,msi-base-spi = <104>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m3: v2m@30000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x30000 0x1000>;
+				arm,msi-base-spi = <120>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m4: v2m@40000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x40000 0x1000>;
+				arm,msi-base-spi = <136>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m5: v2m@50000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x50000 0x1000>;
+				arm,msi-base-spi = <152>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m6: v2m@60000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x60000 0x1000>;
+				arm,msi-base-spi = <168>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m7: v2m@70000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x70000 0x1000>;
+				arm,msi-base-spi = <184>;
+				arm,msi-num-spis = <16>;
+			};
 		};

 		cci@65590000 {

--- a/arch/arm64/boot/dts/exynos/exynos5433-bus.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos5433-bus.dtsi
+/*
+ * Samsung's Exynos5433 SoC Memory interface and AMBA bus device tree source
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ * Chanwoo Choi <cw00.choi@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+&soc {
+	bus_g2d_400: bus0 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_top CLK_ACLK_G2D_400>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_g2d_400_opp_table>;
+		status = "disabled";
+	};
+
+	bus_g2d_266: bus1 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_top CLK_ACLK_G2D_266>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_g2d_266_opp_table>;
+		status = "disabled";
+	};
+
+	bus_gscl: bus2 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_top CLK_ACLK_GSCL_333>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_gscl_opp_table>;
+		status = "disabled";
+	};
+
+	bus_hevc: bus3 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_top CLK_ACLK_HEVC_400>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_hevc_opp_table>;
+		status = "disabled";
+	};
+
+	bus_jpeg: bus4 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_top CLK_SCLK_JPEG_MSCL>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_g2d_400_opp_table>;
+		status = "disabled";
+	};
+
+	bus_mfc: bus5 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_top CLK_ACLK_MFC_400>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_g2d_400_opp_table>;
+		status = "disabled";
+	};
+
+	bus_mscl: bus6 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_top CLK_ACLK_MSCL_400>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_g2d_400_opp_table>;
+		status = "disabled";
+	};
+
+	bus_noc0: bus7 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_top CLK_ACLK_BUS0_400>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_hevc_opp_table>;
+		status = "disabled";
+	};
+
+	bus_noc1: bus8 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_top CLK_ACLK_BUS1_400>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_hevc_opp_table>;
+		status = "disabled";
+	};
+
+	bus_noc2: bus9 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_mif CLK_ACLK_BUS2_400>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_noc2_opp_table>;
+		status = "disabled";
+	};
+
+	bus_g2d_400_opp_table: opp_table2 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp@400000000 {
+			opp-hz = /bits/ 64 <400000000>;
+			opp-microvolt = <1075000>;
+		};
+		opp@267000000 {
+			opp-hz = /bits/ 64 <267000000>;
+			opp-microvolt = <1000000>;
+		};
+		opp@200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-microvolt = <975000>;
+		};
+		opp@160000000 {
+			opp-hz = /bits/ 64 <160000000>;
+			opp-microvolt = <962500>;
+		};
+		opp@134000000 {
+			opp-hz = /bits/ 64 <134000000>;
+			opp-microvolt = <950000>;
+		};
+		opp@100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <937500>;
+		};
+	};
+
+	bus_g2d_266_opp_table: opp_table3 {
+		compatible = "operating-points-v2";
+
+		opp@267000000 {
+			opp-hz = /bits/ 64 <267000000>;
+		};
+		opp@200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+		};
+		opp@160000000 {
+			opp-hz = /bits/ 64 <160000000>;
+		};
+		opp@134000000 {
+			opp-hz = /bits/ 64 <134000000>;
+		};
+		opp@100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+	};
+
+	bus_gscl_opp_table: opp_table4 {
+		compatible = "operating-points-v2";
+
+		opp@333000000 {
+			opp-hz = /bits/ 64 <333000000>;
+		};
+		opp@222000000 {
+			opp-hz = /bits/ 64 <222000000>;
+		};
+		opp@166500000 {
+			opp-hz = /bits/ 64 <166500000>;
+		};
+	};
+
+	bus_hevc_opp_table: opp_table5 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp@400000000 {
+			opp-hz = /bits/ 64 <400000000>;
+		};
+		opp@267000000 {
+			opp-hz = /bits/ 64 <267000000>;
+		};
+		opp@200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+		};
+		opp@160000000 {
+			opp-hz = /bits/ 64 <160000000>;
+		};
+		opp@134000000 {
+			opp-hz = /bits/ 64 <134000000>;
+		};
+		opp@100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+	};
+
+	bus_noc2_opp_table: opp_table6 {
+		compatible = "operating-points-v2";
+
+		opp@400000000 {
+			opp-hz = /bits/ 64 <400000000>;
+		};
+		opp@200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+		};
+		opp@134000000 {
+			opp-hz = /bits/ 64 <134000000>;
+		};
+		opp@100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+	};
+};
--- a/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
@@ -12,25 +12,14 @@
 * published by the Free Software Foundation.
 */

-#define PIN_PULL_NONE		0
-#define PIN_PULL_DOWN		1
-#define PIN_PULL_UP		3
-
-#define PIN_DRV_LV1		0
-#define PIN_DRV_LV2		2
-#define PIN_DRV_LV3		1
-#define PIN_DRV_LV4		3
-
-#define PIN_IN			0
-#define PIN_OUT			1
-#define PIN_FUNC1		2
-
-#define PIN(_func, _pin, _pull, _drv)			\
-	_pin {						\
-		samsung,pins = #_pin;			\
-		samsung,pin-function = <PIN_ ##_func>;	\
-		samsung,pin-pud = <PIN_PULL_ ##_pull>;	\
-		samsung,pin-drv = <PIN_DRV_ ##_drv>;	\
+#include <dt-bindings/pinctrl/samsung.h>
+
+#define PIN(_func, _pin, _pull, _drv)					\
+	_pin {								\
+		samsung,pins = #_pin;					\
+		samsung,pin-function = <EXYNOS_PIN_FUNC_ ##_func>;	\
+		samsung,pin-pud = <EXYNOS_PIN_PULL_ ##_pull>;		\
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_ ##_drv>;		\
 	}

 &pinctrl_alive {
@@ -145,23 +134,23 @@ gpz1: gpz1 {
 	i2s0_bus: i2s0-bus {
 		samsung,pins = "gpz0-0", "gpz0-1", "gpz0-2", "gpz0-3",
 				"gpz0-4", "gpz0-5", "gpz0-6";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <1>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	pcm0_bus: pcm0-bus {
 		samsung,pins = "gpz1-0", "gpz1-1", "gpz1-2", "gpz1-3";
-		samsung,pin-function = <3>;
-		samsung,pin-pud = <1>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	uart_aud_bus: uart-aud-bus {
 		samsung,pins = "gpz1-3", "gpz1-2", "gpz1-1", "gpz1-0";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 };

@@ -196,16 +185,16 @@ gpd5: gpd5 {

 	spi2_bus: spi2-bus {
 		samsung,pins = "gpd5-0", "gpd5-2", "gpd5-3";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	hs_i2c6_bus: hs-i2c6-bus {
 		samsung,pins = "gpd5-3", "gpd5-2";
-		samsung,pin-function = <4>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 };

@@ -260,141 +249,141 @@ gpr3: gpr3 {

 	sd0_clk: sd0-clk {
 		samsung,pins = "gpr0-0";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <3>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};

 	sd0_cmd: sd0-cmd {
 		samsung,pins = "gpr0-1";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <3>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};

 	sd0_rdqs: sd0-rdqs {
 		samsung,pins = "gpr0-2";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <1>;
-		samsung,pin-drv = <3>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};

 	sd0_qrdy: sd0-qrdy {
 		samsung,pins = "gpr0-3";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <1>;
-		samsung,pin-drv = <3>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};

 	sd0_bus1: sd0-bus-width1 {
 		samsung,pins = "gpr1-0";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <3>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};

 	sd0_bus4: sd0-bus-width4 {
 		samsung,pins = "gpr1-1", "gpr1-2", "gpr1-3";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <3>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};

 	sd0_bus8: sd0-bus-width8 {
 		samsung,pins = "gpr1-4", "gpr1-5", "gpr1-6", "gpr1-7";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <3>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};

 	sd1_clk: sd1-clk {
 		samsung,pins = "gpr2-0";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <3>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};

 	sd1_cmd: sd1-cmd {
 		samsung,pins = "gpr2-1";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <3>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};

 	sd1_bus1: sd1-bus-width1 {
 		samsung,pins = "gpr3-0";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <3>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};

 	sd1_bus4: sd1-bus-width4 {
 		samsung,pins = "gpr3-1", "gpr3-2", "gpr3-3";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <3>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};

 	sd1_bus8: sd1-bus-width8 {
 		samsung,pins = "gpr3-4", "gpr3-5", "gpr3-6", "gpr3-7";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <3>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};

 	pcie_bus: pcie_bus {
 		samsung,pins = "gpr3-4", "gpr3-5", "gpr3-6", "gpr3-7";
-		samsung,pin-function = <3>;
-		samsung,pin-pud = <3>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 	};

 	sd2_clk: sd2-clk {
 		samsung,pins = "gpr4-0";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <3>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};

 	sd2_cmd: sd2-cmd {
 		samsung,pins = "gpr4-1";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <3>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};

 	sd2_cd: sd2-cd {
 		samsung,pins = "gpr4-2";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <3>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};

 	sd2_bus1: sd2-bus-width1 {
 		samsung,pins = "gpr4-3";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <3>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};

 	sd2_bus4: sd2-bus-width4 {
 		samsung,pins = "gpr4-4", "gpr4-5", "gpr4-6";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <3>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};

 	sd2_clk_output: sd2-clk-output {
 		samsung,pins = "gpr4-0";
-		samsung,pin-function = <1>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <2>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR3>;
 	};

 	sd2_cmd_output: sd2-cmd-output {
 		samsung,pins = "gpr4-1";
-		samsung,pin-function = <1>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <2>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR3>;
 	};
 };

@@ -419,9 +408,9 @@ gpj0: gpj0 {

 	hs_i2c4_bus: hs-i2c4-bus {
 		samsung,pins = "gpj0-1", "gpj0-0";
-		samsung,pin-function = <4>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 };

@@ -564,225 +553,225 @@ gpg3: gpg3 {

 	hs_i2c8_bus: hs-i2c8-bus {
 		samsung,pins = "gpb0-1", "gpb0-0";
-		samsung,pin-function = <4>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	hs_i2c9_bus: hs-i2c9-bus {
 		samsung,pins = "gpb0-3", "gpb0-2";
-		samsung,pin-function = <4>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	i2s1_bus: i2s1-bus {
 		samsung,pins = "gpd4-0", "gpd4-1", "gpd4-2",
 				"gpd4-3", "gpd4-4";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <1>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	pcm1_bus: pcm1-bus {
 		samsung,pins = "gpd4-0", "gpd4-1", "gpd4-2",
 				"gpd4-3", "gpd4-4";
-		samsung,pin-function = <3>;
-		samsung,pin-pud = <1>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	spdif_bus: spdif-bus {
 		samsung,pins = "gpd4-3", "gpd4-4";
-		samsung,pin-function = <4>;
-		samsung,pin-pud = <1>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	fimc_is_spi_pin0: fimc-is-spi-pin0 {
 		samsung,pins = "gpc3-3", "gpc3-2", "gpc3-1", "gpc3-0";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	fimc_is_spi_pin1: fimc-is-spi-pin1 {
 		samsung,pins = "gpc3-7", "gpc3-6", "gpc3-5", "gpc3-4";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	uart0_bus: uart0-bus {
 		samsung,pins = "gpd0-3", "gpd0-2", "gpd0-1", "gpd0-0";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};

 	hs_i2c2_bus: hs-i2c2-bus {
 		samsung,pins = "gpd0-3", "gpd0-2";
-		samsung,pin-function = <3>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	uart2_bus: uart2-bus {
 		samsung,pins = "gpd1-5", "gpd1-4";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};

 	uart1_bus: uart1-bus {
 		samsung,pins = "gpd1-3", "gpd1-2", "gpd1-1", "gpd1-0";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};

 	hs_i2c3_bus: hs-i2c3-bus {
 		samsung,pins = "gpd1-3", "gpd1-2";
-		samsung,pin-function = <3>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	hs_i2c0_bus: hs-i2c0-bus {
 		samsung,pins = "gpd2-1", "gpd2-0";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	hs_i2c1_bus: hs-i2c1-bus {
 		samsung,pins = "gpd2-3", "gpd2-2";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	pwm0_out: pwm0-out {
 		samsung,pins = "gpd2-4";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	pwm1_out: pwm1-out {
 		samsung,pins = "gpd2-5";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	pwm2_out: pwm2-out {
 		samsung,pins = "gpd2-6";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	pwm3_out: pwm3-out {
 		samsung,pins = "gpd2-7";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	spi1_bus: spi1-bus {
 		samsung,pins = "gpd6-2", "gpd6-4", "gpd6-5";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	hs_i2c7_bus: hs-i2c7-bus {
 		samsung,pins = "gpd2-7", "gpd2-6";
-		samsung,pin-function = <4>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	spi0_bus: spi0-bus {
 		samsung,pins = "gpd8-0", "gpd6-0", "gpd6-1";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	hs_i2c10_bus: hs-i2c10-bus {
 		samsung,pins = "gpg3-1", "gpg3-0";
-		samsung,pin-function = <4>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	hs_i2c11_bus: hs-i2c11-bus {
 		samsung,pins = "gpg3-3", "gpg3-2";
-		samsung,pin-function = <4>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	spi3_bus: spi3-bus {
 		samsung,pins = "gpg3-4", "gpg3-6", "gpg3-7";
-		samsung,pin-function = <3>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	spi4_bus: spi4-bus {
 		samsung,pins = "gpv7-1", "gpv7-3", "gpv7-4";
-		samsung,pin-function = <3>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	fimc_is_uart: fimc-is-uart {
 		samsung,pins = "gpc1-1", "gpc0-7";
-		samsung,pin-function = <3>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	fimc_is_ch0_i2c: fimc-is-ch0_i2c {
 		samsung,pins = "gpc2-1", "gpc2-0";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	fimc_is_ch0_mclk: fimc-is-ch0_mclk {
 		samsung,pins = "gpd7-0";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	fimc_is_ch1_i2c: fimc-is-ch1-i2c {
 		samsung,pins = "gpc2-3", "gpc2-2";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	fimc_is_ch1_mclk: fimc-is-ch1-mclk {
 		samsung,pins = "gpd7-1";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	fimc_is_ch2_i2c: fimc-is-ch2-i2c {
 		samsung,pins = "gpc2-5", "gpc2-4";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};

 	fimc_is_ch2_mclk: fimc-is-ch2-mclk {
 		samsung,pins = "gpd7-2";
-		samsung,pin-function = <2>;
-		samsung,pin-pud = <0>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 };

@@ -797,8 +786,8 @@ gpj1: gpj1 {

 	hs_i2c5_bus: hs-i2c5-bus {
 		samsung,pins = "gpj1-1", "gpj1-0";
-		samsung,pin-function = <4>;
-		samsung,pin-pud = <3>;
-		samsung,pin-drv = <0>;
+		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 };
--- a/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi
+/*
+ * SAMSUNG Exynos5433 TM2 board device tree source
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ *
+ * Common device tree source file for Samsung's TM2 and TM2E boards
+ * which are based on Samsung Exynos5433 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+#include "exynos5433.dtsi"
+#include <dt-bindings/clock/samsung,s2mps11.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	aliases {
+		gsc0 = &gsc_0;
+		gsc1 = &gsc_1;
+		gsc2 = &gsc_2;
+		pinctrl0 = &pinctrl_alive;
+		pinctrl1 = &pinctrl_aud;
+		pinctrl2 = &pinctrl_cpif;
+		pinctrl3 = &pinctrl_ese;
+		pinctrl4 = &pinctrl_finger;
+		pinctrl5 = &pinctrl_fsys;
+		pinctrl6 = &pinctrl_imem;
+		pinctrl7 = &pinctrl_nfc;
+		pinctrl8 = &pinctrl_peric;
+		pinctrl9 = &pinctrl_touch;
+		serial0 = &serial_0;
+		serial1 = &serial_1;
+		serial2 = &serial_2;
+		serial3 = &serial_3;
+		spi0 = &spi_0;
+		spi1 = &spi_1;
+		spi2 = &spi_2;
+		spi3 = &spi_3;
+		spi4 = &spi_4;
+		mshc0 = &mshc_0;
+		mshc2 = &mshc_2;
+	};
+
+	chosen {
+		stdout-path = &serial_1;
+	};
+
+	memory@20000000 {
+		device_type = "memory";
+		reg = <0x0 0x20000000 0x0 0xc0000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		power-key {
+			gpios = <&gpa2 7 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			label = "power key";
+			debounce-interval = <10>;
+		};
+
+		volume-up-key {
+			gpios = <&gpa2 0 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			label = "volume-up key";
+			debounce-interval = <10>;
+		};
+
+		volume-down-key {
+			gpios = <&gpa2 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "volume-down key";
+			debounce-interval = <10>;
+		};
+
+		homepage-key {
+			gpios = <&gpa0 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_MENU>;
+			label = "homepage key";
+			debounce-interval = <10>;
+		};
+	};
+
+	i2c_max98504: i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		gpios = <&gpd0 1 GPIO_ACTIVE_HIGH /* SPK_AMP_SDA */
+			 &gpd0 0 GPIO_ACTIVE_HIGH /* SPK_AMP_SCL */ >;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		max98504: max98504@31 {
+			compatible = "maxim,max98504";
+			reg = <0x31>;
+			maxim,rx-path = <1>;
+			maxim,tx-path = <1>;
+			maxim,tx-channel-mask = <3>;
+			maxim,tx-channel-source = <2>;
+		};
+	};
+
+	sound {
+		compatible = "samsung,tm2-audio";
+		audio-codec = <&wm5110>;
+		i2s-controller = <&i2s0>;
+		audio-amplifier = <&max98504>;
+		mic-bias-gpios = <&gpr3 2 GPIO_ACTIVE_HIGH>;
+		model = "wm5110";
+		samsung,audio-routing =
+			/* Headphone */
+			"HP", "HPOUT1L",
+			"HP", "HPOUT1R",
+
+			/* Speaker */
+			"SPK", "SPKOUT",
+			"SPKOUT", "HPOUT2L",
+			"SPKOUT", "HPOUT2R",
+
+			/* Receiver */
+			"RCV", "HPOUT3L",
+			"RCV", "HPOUT3R";
+		status = "okay";
+	};
+};
+
+&adc {
+	vdd-supply = <&ldo3_reg>;
+	status = "okay";
+
+	thermistor-ap {
+		compatible = "murata,ncp03wf104";
+		pullup-uv = <1800000>;
+		pullup-ohm = <100000>;
+		pulldown-ohm = <0>;
+		io-channels = <&adc 0>;
+	};
+
+	thermistor-battery {
+		compatible = "murata,ncp03wf104";
+		pullup-uv = <1800000>;
+		pullup-ohm = <100000>;
+		pulldown-ohm = <0>;
+		io-channels = <&adc 1>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	thermistor-charger {
+		compatible = "murata,ncp03wf104";
+		pullup-uv = <1800000>;
+		pullup-ohm = <100000>;
+		pulldown-ohm = <0>;
+		io-channels = <&adc 2>;
+	};
+};
+
+&bus_g2d_400 {
+	devfreq-events = <&ppmu_event0_d0_general>, <&ppmu_event0_d1_general>;
+	vdd-supply = <&buck4_reg>;
+	exynos,saturation-ratio = <10>;
+	status = "okay";
+};
+
+&bus_g2d_266 {
+	devfreq = <&bus_g2d_400>;
+	status = "okay";
+};
+
+&bus_gscl {
+	devfreq = <&bus_g2d_400>;
+	status = "okay";
+};
+
+&bus_hevc {
+	devfreq = <&bus_g2d_400>;
+	status = "okay";
+};
+
+&bus_jpeg {
+	devfreq = <&bus_g2d_400>;
+	status = "okay";
+};
+
+&bus_mfc {
+	devfreq = <&bus_g2d_400>;
+	status = "okay";
+};
+
+&bus_mscl {
+	devfreq = <&bus_g2d_400>;
+	status = "okay";
+};
+
+&bus_noc0 {
+	devfreq = <&bus_g2d_400>;
+	status = "okay";
+};
+
+&bus_noc1 {
+	devfreq = <&bus_g2d_400>;
+	status = "okay";
+};
+
+&bus_noc2 {
+	devfreq = <&bus_g2d_400>;
+	status = "okay";
+};
+
+&cmu_aud {
+	assigned-clocks = <&cmu_aud CLK_MOUT_AUD_PLL_USER>;
+	assigned-clock-parents = <&cmu_top CLK_FOUT_AUD_PLL>;
+};
+
+&cmu_disp {
+	assigned-clocks = <&cmu_mif CLK_MOUT_SCLK_DECON_TV_ECLK_A>,
+			  <&cmu_mif CLK_DIV_SCLK_DECON_TV_ECLK>,
+			  <&cmu_disp CLK_MOUT_SCLK_DECON_TV_ECLK_USER>,
+			  <&cmu_disp CLK_MOUT_SCLK_DECON_TV_ECLK>;
+	assigned-clock-parents = <&cmu_mif CLK_MOUT_BUS_PLL_DIV2>,
+				 <0>,
+				 <&cmu_mif CLK_SCLK_DECON_TV_ECLK_DISP>,
+				 <&cmu_disp CLK_MOUT_SCLK_DECON_TV_ECLK_USER>;
+	assigned-clock-rates = <0>, <400000000>;
+};
+
+&cmu_fsys {
+	assigned-clocks = <&cmu_top CLK_MOUT_SCLK_USBDRD30>,
+		<&cmu_top CLK_MOUT_SCLK_USBHOST30>,
+		<&cmu_fsys CLK_MOUT_SCLK_USBDRD30_USER>,
+		<&cmu_fsys CLK_MOUT_SCLK_USBHOST30_USER>,
+		<&cmu_fsys CLK_MOUT_PHYCLK_USBDRD30_UDRD30_PIPE_PCLK_USER>,
+		<&cmu_fsys CLK_MOUT_PHYCLK_USBHOST30_UHOST30_PIPE_PCLK_USER>,
+		<&cmu_fsys CLK_MOUT_PHYCLK_USBDRD30_UDRD30_PHYCLOCK_USER>,
+		<&cmu_fsys CLK_MOUT_PHYCLK_USBHOST30_UHOST30_PHYCLOCK_USER>,
+		<&cmu_top CLK_DIV_SCLK_USBDRD30>,
+		<&cmu_top CLK_DIV_SCLK_USBHOST30>;
+	assigned-clock-parents = <&cmu_top CLK_MOUT_BUS_PLL_USER>,
+		<&cmu_top CLK_MOUT_BUS_PLL_USER>,
+		<&cmu_top CLK_SCLK_USBDRD30_FSYS>,
+		<&cmu_top CLK_SCLK_USBHOST30_FSYS>,
+		<&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PIPE_PCLK_PHY>,
+		<&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PIPE_PCLK_PHY>,
+		<&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PHYCLOCK_PHY>,
+		<&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PHYCLOCK_PHY>;
+	assigned-clock-rates = <0>, <0>, <0>, <0>, <0>, <0>, <0>, <0>,
+			       <66700000>, <66700000>;
+};
+
+&cmu_gscl {
+	assigned-clocks = <&cmu_gscl CLK_MOUT_ACLK_GSCL_111_USER>,
+			  <&cmu_gscl CLK_MOUT_ACLK_GSCL_333_USER>;
+	assigned-clock-parents = <&cmu_top CLK_ACLK_GSCL_111>,
+				 <&cmu_top CLK_ACLK_GSCL_333>;
+};
+
+&cmu_mfc {
+	assigned-clocks = <&cmu_mfc CLK_MOUT_ACLK_MFC_400_USER>;
+	assigned-clock-parents = <&cmu_top CLK_ACLK_MFC_400>;
+};
+
+&cmu_mscl {
+	assigned-clocks = <&cmu_mscl CLK_MOUT_ACLK_MSCL_400_USER>,
+			  <&cmu_mscl CLK_MOUT_SCLK_JPEG_USER>,
+			  <&cmu_mscl CLK_MOUT_SCLK_JPEG>,
+			  <&cmu_top CLK_MOUT_SCLK_JPEG_A>;
+	assigned-clock-parents = <&cmu_top CLK_ACLK_MSCL_400>,
+				 <&cmu_top CLK_SCLK_JPEG_MSCL>,
+				 <&cmu_mscl CLK_MOUT_SCLK_JPEG_USER>,
+				 <&cmu_top CLK_MOUT_BUS_PLL_USER>;
+};
+
+&cpu0 {
+	cpu-supply = <&buck3_reg>;
+};
+
+&cpu4 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&decon {
+	status = "okay";
+
+	i80-if-timings {
+	};
+};
+
+&decon_tv {
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			tv_to_hdmi: endpoint {
+				remote-endpoint = <&hdmi_to_tv>;
+			};
+		};
+	};
+};
+
+&dsi {
+	status = "okay";
+	vddcore-supply = <&ldo6_reg>;
+	vddio-supply = <&ldo7_reg>;
+	samsung,pll-clock-frequency = <24000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&te_irq>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@1 {
+			reg = <1>;
+
+			dsi_out: endpoint {
+				samsung,burst-clock-frequency = <512000000>;
+				samsung,esc-clock-frequency = <16000000>;
+			};
+		};
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpa3 0 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+	vdd-supply = <&ldo6_reg>;
+	vdd_osc-supply = <&ldo7_reg>;
+	vdd_pll-supply = <&ldo6_reg>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			hdmi_to_tv: endpoint {
+				remote-endpoint = <&tv_to_hdmi>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+			hdmi_to_mhl: endpoint {
+				remote-endpoint = <&mhl_to_hdmi>;
+			};
+		};
+	};
+};
+
+&hsi2c_0 {
+	status = "okay";
+	clock-frequency = <2500000>;
+
+	s2mps13-pmic@66 {
+		compatible = "samsung,s2mps13-pmic";
+		interrupt-parent = <&gpa0>;
+		interrupts = <7 IRQ_TYPE_NONE>;
+		reg = <0x66>;
+		samsung,s2mps11-wrstbi-ground;
+
+		s2mps13_osc: clocks {
+			compatible = "samsung,s2mps13-clk";
+			#clock-cells = <1>;
+			clock-output-names = "s2mps13_ap", "s2mps13_cp",
+				"s2mps13_bt";
+		};
+
+		regulators {
+			ldo1_reg: LDO1 {
+				regulator-name = "VDD_ALIVE_0.9V_AP";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-always-on;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "VDDQ_MMC2_2.8V_AP";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo3_reg: LDO3 {
+				regulator-name = "VDD1_E_1.8V_AP";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "VDD10_MIF_PLL_1.0V_AP";
+				regulator-min-microvolt = <1300000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-always-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo5_reg: LDO5 {
+				regulator-name = "VDD10_DPLL_1.0V_AP";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo6_reg: LDO6 {
+				regulator-name = "VDD10_MIPI2L_1.0V_AP";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo7_reg: LDO7 {
+				regulator-name = "VDD18_MIPI2L_1.8V_AP";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo8_reg: LDO8 {
+				regulator-name = "VDD18_LLI_1.8V_AP";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo9_reg: LDO9 {
+				regulator-name = "VDD18_ABB_ETC_1.8V_AP";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo10_reg: LDO10 {
+				regulator-name = "VDD33_USB30_3.0V_AP";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo11_reg: LDO11 {
+				regulator-name = "VDD_INT_M_1.0V_AP";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo12_reg: LDO12 {
+				regulator-name = "VDD_KFC_M_1.1V_AP";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+			};
+
+			ldo13_reg: LDO13 {
+				regulator-name = "VDD_G3D_M_0.95V_AP";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <950000>;
+				regulator-always-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo14_reg: LDO14 {
+				regulator-name = "VDDQ_M1_LDO_1.2V_AP";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo15_reg: LDO15 {
+				regulator-name = "VDDQ_M2_LDO_1.2V_AP";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo16_reg: LDO16 {
+				regulator-name = "VDDQ_EFUSE";
+				regulator-min-microvolt = <1400000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-always-on;
+			};
+
+			ldo17_reg: LDO17 {
+				regulator-name = "V_TFLASH_2.8V_AP";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			ldo18_reg: LDO18 {
+				regulator-name = "V_CODEC_1.8V_AP";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo19_reg: LDO19 {
+				regulator-name = "VDDA_1.8V_COMP";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			ldo20_reg: LDO20 {
+				regulator-name = "VCC_2.8V_AP";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+			};
+
+			ldo21_reg: LDO21 {
+				regulator-name = "VT_CAM_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo22_reg: LDO22 {
+				regulator-name = "CAM_IO_1.8V_AP";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo23_reg: LDO23 {
+				regulator-name = "CAM_SEN_CORE_1.05V_AP";
+				regulator-min-microvolt = <1050000>;
+				regulator-max-microvolt = <1050000>;
+			};
+
+			ldo24_reg: LDO24 {
+				regulator-name = "VT_CAM_1.2V";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			ldo25_reg: LDO25 {
+				regulator-name = "UNUSED_LDO25";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			ldo26_reg: LDO26 {
+				regulator-name = "CAM_AF_2.8V_AP";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			ldo27_reg: LDO27 {
+				regulator-name = "VCC_3.0V_LCD_AP";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+			};
+
+			ldo28_reg: LDO28 {
+				regulator-name = "VCC_1.8V_LCD_AP";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo29_reg: LDO29 {
+				regulator-name = "VT_CAM_2.8V";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+			};
+
+			ldo30_reg: LDO30 {
+				regulator-name = "TSP_AVDD_3.3V_AP";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			ldo31_reg: LDO31 {
+				/*
+				 * LDO31 differs from target to target,
+				 * its definition is in the .dts
+				 */
+			};
+
+			ldo32_reg: LDO32 {
+				regulator-name = "VTOUCH_1.8V_AP";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo33_reg: LDO33 {
+				regulator-name = "VTOUCH_LED_3.3V";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-ramp-delay = <12500>;
+			};
+
+			ldo34_reg: LDO34 {
+				regulator-name = "VCC_1.8V_MHL_AP";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <2100000>;
+			};
+
+			ldo35_reg: LDO35 {
+				regulator-name = "OIS_VM_2.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			ldo36_reg: LDO36 {
+				regulator-name = "VSIL_1.0V";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+			};
+
+			ldo37_reg: LDO37 {
+				regulator-name = "VF_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo38_reg: LDO38 {
+				/*
+				 * LDO38 differs from target to target,
+				 * its definition is in the .dts
+				 */
+			};
+
+			ldo39_reg: LDO39 {
+				regulator-name = "V_HRM_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo40_reg: LDO40 {
+				regulator-name = "V_HRM_3.3V";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			buck1_reg: BUCK1 {
+				regulator-name = "VDD_MIF_0.9V_AP";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "VDD_EGL_1.0V_AP";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-always-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck3_reg: BUCK3 {
+				regulator-name = "VDD_KFC_1.0V_AP";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck4_reg: BUCK4 {
+				regulator-name = "VDD_INT_0.95V_AP";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck5_reg: BUCK5 {
+				regulator-name = "VDD_DISP_CAM0_0.9V_AP";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck6_reg: BUCK6 {
+				regulator-name = "VDD_G3D_0.9V_AP";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck7_reg: BUCK7 {
+				regulator-name = "VDD_MEM1_1.2V_AP";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+			};
+
+			buck8_reg: BUCK8 {
+				regulator-name = "VDD_LLDO_1.35V_AP";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			buck9_reg: BUCK9 {
+				regulator-name = "VDD_MLDO_2.0V_AP";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			buck10_reg: BUCK10 {
+				regulator-name = "vdd_mem2";
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&hsi2c_7 {
+	status = "okay";
+
+	sii8620@39 {
+		reg = <0x39>;
+		compatible = "sil,sii8620";
+		cvcc10-supply = <&ldo36_reg>;
+		iovcc18-supply = <&ldo34_reg>;
+		interrupt-parent = <&gpf0>;
+		interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
+		reset-gpios = <&gpv7 0 GPIO_ACTIVE_LOW>;
+		clocks = <&pmu_system_controller 0>;
+		clock-names = "xtal";
+
+		port {
+			mhl_to_hdmi: endpoint {
+				remote-endpoint = <&hdmi_to_mhl>;
+			};
+		};
+	};
+};
+
+&hsi2c_8 {
+	status = "okay";
+
+	max77843@66 {
+		compatible = "maxim,max77843";
+		interrupt-parent = <&gpa1>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+		reg = <0x66>;
+
+		muic: max77843-muic {
+			compatible = "maxim,max77843-muic";
+		};
+
+		regulators {
+			compatible = "maxim,max77843-regulator";
+			safeout1_reg: SAFEOUT1 {
+				regulator-name = "SAFEOUT1";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <4950000>;
+			};
+
+			safeout2_reg: SAFEOUT2 {
+				regulator-name = "SAFEOUT2";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <4950000>;
+			};
+
+			charger_reg: CHARGER {
+				regulator-name = "CHARGER";
+				regulator-min-microamp = <100000>;
+				regulator-max-microamp = <3150000>;
+			};
+		};
+
+		haptic: max77843-haptic {
+			compatible = "maxim,max77843-haptic";
+			haptic-supply = <&ldo38_reg>;
+			pwms = <&pwm 0 33670 0>;
+			pwm-names = "haptic";
+		};
+	};
+};
+
+&hsi2c_11 {
+	status = "okay";
+};
+
+&i2s0 {
+	status = "okay";
+};
+
+&mshc_0 {
+	status = "okay";
+	num-slots = <1>;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	cap-mmc-highspeed;
+	non-removable;
+	card-detect-delay = <200>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <0 4>;
+	samsung,dw-mshc-ddr-timing = <0 2>;
+	samsung,dw-mshc-hs400-timing = <0 3>;
+	samsung,read-strobe-delay = <90>;
+	fifo-depth = <0x80>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_qrdy &sd0_bus1 &sd0_bus4
+			&sd0_bus8 &sd0_rdqs>;
+	bus-width = <8>;
+	assigned-clocks = <&cmu_top CLK_SCLK_MMC0_FSYS>;
+	assigned-clock-rates = <800000000>;
+};
+
+&mshc_2 {
+	status = "okay";
+	num-slots = <1>;
+	cap-sd-highspeed;
+	disable-wp;
+	cd-gpios = <&gpa2 4 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+	card-detect-delay = <200>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <0 4>;
+	samsung,dw-mshc-ddr-timing = <0 2>;
+	fifo-depth = <0x80>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus1 &sd2_bus4>;
+	bus-width = <4>;
+};
+
+&ppmu_d0_general {
+	status = "okay";
+	events {
+		ppmu_event0_d0_general: ppmu-event0-d0-general {
+			event-name = "ppmu-event0-d0-general";
+		};
+	};
+};
+
+&ppmu_d1_general {
+	status = "okay";
+	events {
+		ppmu_event0_d1_general: ppmu-event0-d1-general {
+		       event-name = "ppmu-event0-d1-general";
+	       };
+       };
+};
+
+&pinctrl_alive {
+	pinctrl-names = "default";
+	pinctrl-0 = <&initial_alive>;
+
+	initial_alive: initial-state {
+		PIN(INPUT, gpa0-0, DOWN, FAST_SR1);
+		PIN(INPUT, gpa0-1, NONE, FAST_SR1);
+		PIN(INPUT, gpa0-2, DOWN, FAST_SR1);
+		PIN(INPUT, gpa0-3, NONE, FAST_SR1);
+		PIN(INPUT, gpa0-4, NONE, FAST_SR1);
+		PIN(INPUT, gpa0-5, DOWN, FAST_SR1);
+		PIN(INPUT, gpa0-6, NONE, FAST_SR1);
+		PIN(INPUT, gpa0-7, NONE, FAST_SR1);
+
+		PIN(INPUT, gpa1-0, UP, FAST_SR1);
+		PIN(INPUT, gpa1-1, NONE, FAST_SR1);
+		PIN(INPUT, gpa1-2, NONE, FAST_SR1);
+		PIN(INPUT, gpa1-3, DOWN, FAST_SR1);
+		PIN(INPUT, gpa1-4, DOWN, FAST_SR1);
+		PIN(INPUT, gpa1-5, NONE, FAST_SR1);
+		PIN(INPUT, gpa1-6, NONE, FAST_SR1);
+		PIN(INPUT, gpa1-7, NONE, FAST_SR1);
+
+		PIN(INPUT, gpa2-0, NONE, FAST_SR1);
+		PIN(INPUT, gpa2-1, NONE, FAST_SR1);
+		PIN(INPUT, gpa2-2, NONE, FAST_SR1);
+		PIN(INPUT, gpa2-3, DOWN, FAST_SR1);
+		PIN(INPUT, gpa2-4, NONE, FAST_SR1);
+		PIN(INPUT, gpa2-5, DOWN, FAST_SR1);
+		PIN(INPUT, gpa2-6, DOWN, FAST_SR1);
+		PIN(INPUT, gpa2-7, NONE, FAST_SR1);
+
+		PIN(INPUT, gpa3-0, DOWN, FAST_SR1);
+		PIN(INPUT, gpa3-1, DOWN, FAST_SR1);
+		PIN(INPUT, gpa3-2, NONE, FAST_SR1);
+		PIN(INPUT, gpa3-3, DOWN, FAST_SR1);
+		PIN(INPUT, gpa3-4, NONE, FAST_SR1);
+		PIN(INPUT, gpa3-5, DOWN, FAST_SR1);
+		PIN(INPUT, gpa3-6, DOWN, FAST_SR1);
+		PIN(INPUT, gpa3-7, DOWN, FAST_SR1);
+
+		PIN(INPUT, gpf1-0, NONE, FAST_SR1);
+		PIN(INPUT, gpf1-1, NONE, FAST_SR1);
+		PIN(INPUT, gpf1-2, DOWN, FAST_SR1);
+		PIN(INPUT, gpf1-4, UP, FAST_SR1);
+		PIN(OUTPUT, gpf1-5, NONE, FAST_SR1);
+		PIN(INPUT, gpf1-6, DOWN, FAST_SR1);
+		PIN(INPUT, gpf1-7, DOWN, FAST_SR1);
+
+		PIN(INPUT, gpf2-0, DOWN, FAST_SR1);
+		PIN(INPUT, gpf2-1, DOWN, FAST_SR1);
+		PIN(INPUT, gpf2-2, DOWN, FAST_SR1);
+		PIN(INPUT, gpf2-3, DOWN, FAST_SR1);
+
+		PIN(INPUT, gpf3-0, DOWN, FAST_SR1);
+		PIN(INPUT, gpf3-1, DOWN, FAST_SR1);
+		PIN(INPUT, gpf3-2, NONE, FAST_SR1);
+		PIN(INPUT, gpf3-3, DOWN, FAST_SR1);
+
+		PIN(INPUT, gpf4-0, DOWN, FAST_SR1);
+		PIN(INPUT, gpf4-1, DOWN, FAST_SR1);
+		PIN(INPUT, gpf4-2, DOWN, FAST_SR1);
+		PIN(INPUT, gpf4-3, DOWN, FAST_SR1);
+		PIN(INPUT, gpf4-4, DOWN, FAST_SR1);
+		PIN(INPUT, gpf4-5, DOWN, FAST_SR1);
+		PIN(INPUT, gpf4-6, DOWN, FAST_SR1);
+		PIN(INPUT, gpf4-7, DOWN, FAST_SR1);
+
+		PIN(INPUT, gpf5-0, DOWN, FAST_SR1);
+		PIN(INPUT, gpf5-1, DOWN, FAST_SR1);
+		PIN(INPUT, gpf5-2, DOWN, FAST_SR1);
+		PIN(INPUT, gpf5-3, DOWN, FAST_SR1);
+		PIN(OUTPUT, gpf5-4, NONE, FAST_SR1);
+		PIN(INPUT, gpf5-5, DOWN, FAST_SR1);
+		PIN(INPUT, gpf5-6, DOWN, FAST_SR1);
+		PIN(INPUT, gpf5-7, DOWN, FAST_SR1);
+	};
+
+	te_irq: te_irq {
+		samsung,pins = "gpf1-3";
+		samsung,pin-function = <0xf>;
+	};
+};
+
+&pinctrl_cpif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&initial_cpif>;
+
+	initial_cpif: initial-state {
+		PIN(INPUT, gpv6-0, DOWN, FAST_SR1);
+		PIN(INPUT, gpv6-1, DOWN, FAST_SR1);
+	};
+};
+
+&pinctrl_ese {
+	pinctrl-names = "default";
+	pinctrl-0 = <&initial_ese>;
+
+	initial_ese: initial-state {
+		PIN(INPUT, gpj2-0, DOWN, FAST_SR1);
+		PIN(INPUT, gpj2-1, DOWN, FAST_SR1);
+		PIN(INPUT, gpj2-2, DOWN, FAST_SR1);
+	};
+};
+
+&pinctrl_fsys {
+	pinctrl-names = "default";
+	pinctrl-0 = <&initial_fsys>;
+
+	initial_fsys: initial-state {
+		PIN(INPUT, gpr3-0, NONE, FAST_SR1);
+		PIN(INPUT, gpr3-1, DOWN, FAST_SR1);
+		PIN(INPUT, gpr3-2, DOWN, FAST_SR1);
+		PIN(INPUT, gpr3-3, DOWN, FAST_SR1);
+		PIN(INPUT, gpr3-7, NONE, FAST_SR1);
+	};
+};
+
+&pinctrl_imem {
+	pinctrl-names = "default";
+	pinctrl-0 = <&initial_imem>;
+
+	initial_imem: initial-state {
+		PIN(INPUT, gpf0-0, UP, FAST_SR1);
+		PIN(INPUT, gpf0-1, UP, FAST_SR1);
+		PIN(INPUT, gpf0-2, DOWN, FAST_SR1);
+		PIN(INPUT, gpf0-3, UP, FAST_SR1);
+		PIN(INPUT, gpf0-4, DOWN, FAST_SR1);
+		PIN(INPUT, gpf0-5, NONE, FAST_SR1);
+		PIN(INPUT, gpf0-6, DOWN, FAST_SR1);
+		PIN(INPUT, gpf0-7, UP, FAST_SR1);
+	};
+};
+
+&pinctrl_nfc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&initial_nfc>;
+
+	initial_nfc: initial-state {
+		PIN(INPUT, gpj0-2, DOWN, FAST_SR1);
+	};
+};
+
+&pinctrl_peric {
+	pinctrl-names = "default";
+	pinctrl-0 = <&initial_peric>;
+
+	initial_peric: initial-state {
+		PIN(INPUT, gpv7-0, DOWN, FAST_SR1);
+		PIN(INPUT, gpv7-1, DOWN, FAST_SR1);
+		PIN(INPUT, gpv7-2, NONE, FAST_SR1);
+		PIN(INPUT, gpv7-3, DOWN, FAST_SR1);
+		PIN(INPUT, gpv7-4, DOWN, FAST_SR1);
+		PIN(INPUT, gpv7-5, DOWN, FAST_SR1);
+
+		PIN(INPUT, gpb0-4, DOWN, FAST_SR1);
+
+		PIN(INPUT, gpc0-2, DOWN, FAST_SR1);
+		PIN(INPUT, gpc0-5, DOWN, FAST_SR1);
+		PIN(INPUT, gpc0-7, DOWN, FAST_SR1);
+
+		PIN(INPUT, gpc1-1, DOWN, FAST_SR1);
+
+		PIN(INPUT, gpc3-4, NONE, FAST_SR1);
+		PIN(INPUT, gpc3-5, NONE, FAST_SR1);
+		PIN(INPUT, gpc3-6, NONE, FAST_SR1);
+		PIN(INPUT, gpc3-7, NONE, FAST_SR1);
+
+		PIN(OUTPUT, gpg0-0, NONE, FAST_SR1);
+		PIN(2, gpg0-1, DOWN, FAST_SR1);
+
+		PIN(INPUT, gpd2-5, DOWN, FAST_SR1);
+
+		PIN(INPUT, gpd4-0, NONE, FAST_SR1);
+		PIN(INPUT, gpd4-1, DOWN, FAST_SR1);
+		PIN(INPUT, gpd4-2, DOWN, FAST_SR1);
+		PIN(INPUT, gpd4-3, DOWN, FAST_SR1);
+		PIN(INPUT, gpd4-4, DOWN, FAST_SR1);
+
+		PIN(INPUT, gpd6-3, DOWN, FAST_SR1);
+
+		PIN(INPUT, gpd8-1, UP, FAST_SR1);
+
+		PIN(INPUT, gpg1-0, DOWN, FAST_SR1);
+		PIN(INPUT, gpg1-1, DOWN, FAST_SR1);
+		PIN(INPUT, gpg1-2, DOWN, FAST_SR1);
+		PIN(INPUT, gpg1-3, DOWN, FAST_SR1);
+		PIN(INPUT, gpg1-4, DOWN, FAST_SR1);
+
+		PIN(INPUT, gpg2-0, DOWN, FAST_SR1);
+		PIN(INPUT, gpg2-1, DOWN, FAST_SR1);
+
+		PIN(INPUT, gpg3-0, DOWN, FAST_SR1);
+		PIN(INPUT, gpg3-1, DOWN, FAST_SR1);
+		PIN(INPUT, gpg3-5, DOWN, FAST_SR1);
+		PIN(INPUT, gpg3-7, DOWN, FAST_SR1);
+	};
+};
+
+&pinctrl_touch {
+	pinctrl-names = "default";
+	pinctrl-0 = <&initial_touch>;
+
+	initial_touch: initial-state {
+		PIN(INPUT, gpj1-2, DOWN, FAST_SR1);
+	};
+};
+
+&pwm {
+	pinctrl-0 = <&pwm0_out>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&mic {
+	status = "okay";
+
+	i80-if-timings {
+	};
+};
+
+&pmu_system_controller {
+	assigned-clocks = <&pmu_system_controller 0>;
+	assigned-clock-parents = <&xxti>;
+};
+
+&serial_1 {
+	status = "okay";
+};
+
+&spi_1 {
+	cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	wm5110: wm5110-codec@0 {
+		compatible = "wlf,wm5110";
+		reg = <0x0>;
+		spi-max-frequency = <20000000>;
+		interrupt-parent = <&gpa0>;
+		interrupts = <4 IRQ_TYPE_NONE>;
+		clocks = <&pmu_system_controller 0>,
+			<&s2mps13_osc S2MPS11_CLK_BT>;
+		clock-names = "mclk1", "mclk2";
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		wlf,micd-detect-debounce = <300>;
+		wlf,micd-bias-start-time = <0x1>;
+		wlf,micd-rate = <0x7>;
+		wlf,micd-dbtime = <0x1>;
+		wlf,micd-force-micbias;
+		wlf,micd-configs = <0x0 1 0>;
+		wlf,hpdet-channel = <1>;
+		wlf,gpsw = <0x1>;
+		wlf,inmode = <2 0 2 0>;
+
+		wlf,reset = <&gpc0 7 GPIO_ACTIVE_HIGH>;
+		wlf,ldoena = <&gpf0 0 GPIO_ACTIVE_HIGH>;
+
+		/* core supplies */
+		AVDD-supply = <&ldo18_reg>;
+		DBVDD1-supply = <&ldo18_reg>;
+		CPVDD-supply = <&ldo18_reg>;
+		DBVDD2-supply = <&ldo18_reg>;
+		DBVDD3-supply = <&ldo18_reg>;
+
+		controller-data {
+			samsung,spi-feedback-delay = <0>;
+		};
+	};
+};
+
+&timer {
+	clock-frequency = <24000000>;
+};
+
+&tmu_atlas0 {
+	vtmu-supply = <&ldo3_reg>;
+	status = "okay";
+};
+
+&tmu_apollo {
+	vtmu-supply = <&ldo3_reg>;
+	status = "okay";
+};
+
+&tmu_g3d {
+	vtmu-supply = <&ldo3_reg>;
+	status = "okay";
+};
+
+&usbdrd30 {
+	vdd33-supply = <&ldo10_reg>;
+	vdd10-supply = <&ldo6_reg>;
+	status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+	dr_mode = "otg";
+};
+
+&usbdrd30_phy {
+	vbus-supply = <&safeout1_reg>;
+	status = "okay";
+};
+
+&xxti {
+	clock-frequency = <24000000>;
+};
--- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
@@ -11,1039 +11,34 @@
 * published by the Free Software Foundation.
 */

-/dts-v1/;
-#include "exynos5433.dtsi"
-#include <dt-bindings/clock/samsung,s2mps11.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
+#include "exynos5433-tm2-common.dtsi"

 / {
 	model = "Samsung TM2 board";
 	compatible = "samsung,tm2", "samsung,exynos5433";
-
-	aliases {
-		gsc0 = &gsc_0;
-		gsc1 = &gsc_1;
-		gsc2 = &gsc_2;
-		pinctrl0 = &pinctrl_alive;
-		pinctrl1 = &pinctrl_aud;
-		pinctrl2 = &pinctrl_cpif;
-		pinctrl3 = &pinctrl_ese;
-		pinctrl4 = &pinctrl_finger;
-		pinctrl5 = &pinctrl_fsys;
-		pinctrl6 = &pinctrl_imem;
-		pinctrl7 = &pinctrl_nfc;
-		pinctrl8 = &pinctrl_peric;
-		pinctrl9 = &pinctrl_touch;
-		serial0 = &serial_0;
-		serial1 = &serial_1;
-		serial2 = &serial_2;
-		serial3 = &serial_3;
-		spi0 = &spi_0;
-		spi1 = &spi_1;
-		spi2 = &spi_2;
-		spi3 = &spi_3;
-		spi4 = &spi_4;
-		mshc0 = &mshc_0;
-		mshc2 = &mshc_2;
-	};
-
-	chosen {
-		stdout-path = &serial_1;
-	};
-
-	memory@20000000 {
-		device_type = "memory";
-		reg = <0x0 0x20000000 0x0 0xc0000000>;
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		power-key {
-			gpios = <&gpa2 7 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_POWER>;
-			label = "power key";
-			debounce-interval = <10>;
-		};
-
-		volume-up-key {
-			gpios = <&gpa2 0 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEUP>;
-			label = "volume-up key";
-			debounce-interval = <10>;
-		};
-
-		volume-down-key {
-			gpios = <&gpa2 1 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
-			label = "volume-down key";
-			debounce-interval = <10>;
-		};
-
-		homepage-key {
-			gpios = <&gpa0 3 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_MENU>;
-			label = "homepage key";
-			debounce-interval = <10>;
-		};
-	};
-
-	i2c_max98504: i2c-gpio-0 {
-		compatible = "i2c-gpio";
-		gpios = <&gpd0 1 GPIO_ACTIVE_HIGH /* SPK_AMP_SDA */
-			 &gpd0 0 GPIO_ACTIVE_HIGH /* SPK_AMP_SCL */ >;
-		i2c-gpio,delay-us = <2>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		status = "okay";
-
-		max98504: max98504@31 {
-			compatible = "maxim,max98504";
-			reg = <0x31>;
-			maxim,rx-path = <1>;
-			maxim,tx-path = <1>;
-			maxim,tx-channel-mask = <3>;
-			maxim,tx-channel-source = <2>;
-		};
-	};
-
-	sound {
-		compatible = "samsung,tm2-audio";
-		audio-codec = <&wm5110>;
-		i2s-controller = <&i2s0>;
-		audio-amplifier = <&max98504>;
-		mic-bias-gpios = <&gpr3 2 GPIO_ACTIVE_HIGH>;
-		model = "wm5110";
-		samsung,audio-routing =
-			/* Headphone */
-			"HP", "HPOUT1L",
-			"HP", "HPOUT1R",
-
-			/* Speaker */
-			"SPK", "SPKOUT",
-			"SPKOUT", "HPOUT2L",
-			"SPKOUT", "HPOUT2R",
-
-			/* Receiver */
-			"RCV", "HPOUT3L",
-			"RCV", "HPOUT3R";
-		status = "okay";
-	};
-};
-
-&adc {
-	vdd-supply = <&ldo3_reg>;
-	status = "okay";
-
-	thermistor-ap {
-		compatible = "murata,ncp03wf104";
-		pullup-uv = <1800000>;
-		pullup-ohm = <100000>;
-		pulldown-ohm = <0>;
-		io-channels = <&adc 0>;
-	};
-
-	thermistor-battery {
-		compatible = "murata,ncp03wf104";
-		pullup-uv = <1800000>;
-		pullup-ohm = <100000>;
-		pulldown-ohm = <0>;
-		io-channels = <&adc 1>;
-		#thermal-sensor-cells = <0>;
-	};
-
-	thermistor-charger {
-		compatible = "murata,ncp03wf104";
-		pullup-uv = <1800000>;
-		pullup-ohm = <100000>;
-		pulldown-ohm = <0>;
-		io-channels = <&adc 2>;
-	};
-};
-
-&cmu_aud {
-	assigned-clocks = <&cmu_aud CLK_MOUT_AUD_PLL_USER>;
-	assigned-clock-parents = <&cmu_top CLK_FOUT_AUD_PLL>;
-};
-
-&cmu_fsys {
-	assigned-clocks = <&cmu_top CLK_MOUT_SCLK_USBDRD30>,
-		<&cmu_top CLK_MOUT_SCLK_USBHOST30>,
-		<&cmu_fsys CLK_MOUT_SCLK_USBDRD30_USER>,
-		<&cmu_fsys CLK_MOUT_SCLK_USBHOST30_USER>,
-		<&cmu_fsys CLK_MOUT_PHYCLK_USBDRD30_UDRD30_PIPE_PCLK_USER>,
-		<&cmu_fsys CLK_MOUT_PHYCLK_USBHOST30_UHOST30_PIPE_PCLK_USER>,
-		<&cmu_fsys CLK_MOUT_PHYCLK_USBDRD30_UDRD30_PHYCLOCK_USER>,
-		<&cmu_fsys CLK_MOUT_PHYCLK_USBHOST30_UHOST30_PHYCLOCK_USER>,
-		<&cmu_top CLK_DIV_SCLK_USBDRD30>,
-		<&cmu_top CLK_DIV_SCLK_USBHOST30>;
-	assigned-clock-parents = <&cmu_top CLK_MOUT_BUS_PLL_USER>,
-		<&cmu_top CLK_MOUT_BUS_PLL_USER>,
-		<&cmu_top CLK_SCLK_USBDRD30_FSYS>,
-		<&cmu_top CLK_SCLK_USBHOST30_FSYS>,
-		<&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PIPE_PCLK_PHY>,
-		<&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PIPE_PCLK_PHY>,
-		<&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PHYCLOCK_PHY>,
-		<&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PHYCLOCK_PHY>;
-	assigned-clock-rates = <0>, <0>, <0>, <0>, <0>, <0>, <0>, <0>,
-			       <66700000>, <66700000>;
-};
-
-&cmu_gscl {
-	assigned-clocks = <&cmu_gscl CLK_MOUT_ACLK_GSCL_111_USER>,
-			  <&cmu_gscl CLK_MOUT_ACLK_GSCL_333_USER>;
-	assigned-clock-parents = <&cmu_top CLK_ACLK_GSCL_111>,
-				 <&cmu_top CLK_ACLK_GSCL_333>;
-};
-
-&cmu_mfc {
-	assigned-clocks = <&cmu_mfc CLK_MOUT_ACLK_MFC_400_USER>;
-	assigned-clock-parents = <&cmu_top CLK_ACLK_MFC_400>;
-};
-
-&cmu_mscl {
-	assigned-clocks = <&cmu_mscl CLK_MOUT_ACLK_MSCL_400_USER>,
-			  <&cmu_mscl CLK_MOUT_SCLK_JPEG_USER>,
-			  <&cmu_mscl CLK_MOUT_SCLK_JPEG>,
-			  <&cmu_top CLK_MOUT_SCLK_JPEG_A>;
-	assigned-clock-parents = <&cmu_top CLK_ACLK_MSCL_400>,
-				 <&cmu_top CLK_SCLK_JPEG_MSCL>,
-				 <&cmu_mscl CLK_MOUT_SCLK_JPEG_USER>,
-				 <&cmu_top CLK_MOUT_BUS_PLL_USER>;
-};
-
-&cpu0 {
-	cpu-supply = <&buck3_reg>;
-};
-
-&cpu4 {
-	cpu-supply = <&buck2_reg>;
-};
-
-&decon {
-	status = "okay";
-
-	i80-if-timings {
-	};
-};
-
-&dsi {
-	status = "okay";
-	vddcore-supply = <&ldo6_reg>;
-	vddio-supply = <&ldo7_reg>;
-	samsung,pll-clock-frequency = <24000000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&te_irq>;
-
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		port@1 {
-			reg = <1>;
-
-			dsi_out: endpoint {
-				samsung,burst-clock-frequency = <512000000>;
-				samsung,esc-clock-frequency = <16000000>;
-			};
-		};
-	};
-};
-
-&hsi2c_0 {
-	status = "okay";
-	clock-frequency = <2500000>;
-
-	s2mps13-pmic@66 {
-		compatible = "samsung,s2mps13-pmic";
-		interrupt-parent = <&gpa0>;
-		interrupts = <7 IRQ_TYPE_NONE>;
-		reg = <0x66>;
-		samsung,s2mps11-wrstbi-ground;
-
-		s2mps13_osc: clocks {
-			compatible = "samsung,s2mps13-clk";
-			#clock-cells = <1>;
-			clock-output-names = "s2mps13_ap", "s2mps13_cp",
-				"s2mps13_bt";
-		};
-
-		regulators {
-			ldo1_reg: LDO1 {
-				regulator-name = "VDD_ALIVE_0.9V_AP";
-				regulator-min-microvolt = <900000>;
-				regulator-max-microvolt = <900000>;
-				regulator-always-on;
-			};
-
-			ldo2_reg: LDO2 {
-				regulator-name = "VDDQ_MMC2_2.8V_AP";
-				regulator-min-microvolt = <2800000>;
-				regulator-max-microvolt = <2800000>;
-				regulator-always-on;
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			ldo3_reg: LDO3 {
-				regulator-name = "VDD1_E_1.8V_AP";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-always-on;
-			};
-
-			ldo4_reg: LDO4 {
-				regulator-name = "VDD10_MIF_PLL_1.0V_AP";
-				regulator-min-microvolt = <1300000>;
-				regulator-max-microvolt = <1300000>;
-				regulator-always-on;
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			ldo5_reg: LDO5 {
-				regulator-name = "VDD10_DPLL_1.0V_AP";
-				regulator-min-microvolt = <1000000>;
-				regulator-max-microvolt = <1000000>;
-				regulator-always-on;
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			ldo6_reg: LDO6 {
-				regulator-name = "VDD10_MIPI2L_1.0V_AP";
-				regulator-min-microvolt = <1000000>;
-				regulator-max-microvolt = <1000000>;
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			ldo7_reg: LDO7 {
-				regulator-name = "VDD18_MIPI2L_1.8V_AP";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-			};
-
-			ldo8_reg: LDO8 {
-				regulator-name = "VDD18_LLI_1.8V_AP";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-always-on;
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			ldo9_reg: LDO9 {
-				regulator-name = "VDD18_ABB_ETC_1.8V_AP";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-always-on;
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			ldo10_reg: LDO10 {
-				regulator-name = "VDD33_USB30_3.0V_AP";
-				regulator-min-microvolt = <3000000>;
-				regulator-max-microvolt = <3000000>;
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			ldo11_reg: LDO11 {
-				regulator-name = "VDD_INT_M_1.0V_AP";
-				regulator-min-microvolt = <1000000>;
-				regulator-max-microvolt = <1000000>;
-				regulator-always-on;
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			ldo12_reg: LDO12 {
-				regulator-name = "VDD_KFC_M_1.1V_AP";
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <1350000>;
-				regulator-always-on;
-			};
-
-			ldo13_reg: LDO13 {
-				regulator-name = "VDD_G3D_M_0.95V_AP";
-				regulator-min-microvolt = <950000>;
-				regulator-max-microvolt = <950000>;
-				regulator-always-on;
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			ldo14_reg: LDO14 {
-				regulator-name = "VDDQ_M1_LDO_1.2V_AP";
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <1200000>;
-				regulator-always-on;
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			ldo15_reg: LDO15 {
-				regulator-name = "VDDQ_M2_LDO_1.2V_AP";
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <1200000>;
-				regulator-always-on;
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			ldo16_reg: LDO16 {
-				regulator-name = "VDDQ_EFUSE";
-				regulator-min-microvolt = <1400000>;
-				regulator-max-microvolt = <3400000>;
-				regulator-always-on;
-			};
-
-			ldo17_reg: LDO17 {
-				regulator-name = "V_TFLASH_2.8V_AP";
-				regulator-min-microvolt = <2800000>;
-				regulator-max-microvolt = <2800000>;
-			};
-
-			ldo18_reg: LDO18 {
-				regulator-name = "V_CODEC_1.8V_AP";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-			};
-
-			ldo19_reg: LDO19 {
-				regulator-name = "VDDA_1.8V_COMP";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-always-on;
-			};
-
-			ldo20_reg: LDO20 {
-				regulator-name = "VCC_2.8V_AP";
-				regulator-min-microvolt = <2800000>;
-				regulator-max-microvolt = <2800000>;
-				regulator-always-on;
-			};
-
-			ldo21_reg: LDO21 {
-				regulator-name = "VT_CAM_1.8V";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-			};
-
-			ldo22_reg: LDO22 {
-				regulator-name = "CAM_IO_1.8V_AP";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-			};
-
-			ldo23_reg: LDO23 {
-				regulator-name = "CAM_SEN_CORE_1.2V_AP";
-				regulator-min-microvolt = <1050000>;
-				regulator-max-microvolt = <1200000>;
-			};
-
-			ldo24_reg: LDO24 {
-				regulator-name = "VT_CAM_1.2V";
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <1200000>;
-			};
-
-			ldo25_reg: LDO25 {
-				regulator-name = "CAM_SEN_A2.8V_AP";
-				regulator-min-microvolt = <2800000>;
-				regulator-max-microvolt = <2800000>;
-			};
-
-			ldo26_reg: LDO26 {
-				regulator-name = "CAM_AF_2.8V_AP";
-				regulator-min-microvolt = <2800000>;
-				regulator-max-microvolt = <2800000>;
-			};
-
-			ldo27_reg: LDO27 {
-				regulator-name = "VCC_3.0V_LCD_AP";
-				regulator-min-microvolt = <3000000>;
-				regulator-max-microvolt = <3000000>;
-			};
-
-			ldo28_reg: LDO28 {
-				regulator-name = "VCC_1.8V_LCD_AP";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-			};
-
-			ldo29_reg: LDO29 {
-				regulator-name = "VT_CAM_2.8V";
-				regulator-min-microvolt = <3000000>;
-				regulator-max-microvolt = <3000000>;
-			};
-
-			ldo30_reg: LDO30 {
-				regulator-name = "TSP_AVDD_3.3V_AP";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-			};
-
-			ldo31_reg: LDO31 {
-				regulator-name = "TSP_VDD_1.85V_AP";
-				regulator-min-microvolt = <1850000>;
-				regulator-max-microvolt = <1850000>;
-			};
-
-			ldo32_reg: LDO32 {
-				regulator-name = "VTOUCH_1.8V_AP";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-			};
-
-			ldo33_reg: LDO33 {
-				regulator-name = "VTOUCH_LED_3.3V";
-				regulator-min-microvolt = <2500000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-ramp-delay = <12500>;
-			};
-
-			ldo34_reg: LDO34 {
-				regulator-name = "VCC_1.8V_MHL_AP";
-				regulator-min-microvolt = <1000000>;
-				regulator-max-microvolt = <2100000>;
-			};
-
-			ldo35_reg: LDO35 {
-				regulator-name = "OIS_VM_2.8V";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <2800000>;
-			};
-
-			ldo36_reg: LDO36 {
-				regulator-name = "VSIL_1.0V";
-				regulator-min-microvolt = <1000000>;
-				regulator-max-microvolt = <1000000>;
-			};
-
-			ldo37_reg: LDO37 {
-				regulator-name = "VF_1.8V";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-			};
-
-			ldo38_reg: LDO38 {
-				regulator-name = "VCC_3.0V_MOTOR_AP";
-				regulator-min-microvolt = <3000000>;
-				regulator-max-microvolt = <3000000>;
-			};
-
-			ldo39_reg: LDO39 {
-				regulator-name = "V_HRM_1.8V";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-			};
-
-			ldo40_reg: LDO40 {
-				regulator-name = "V_HRM_3.3V";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-			};
-
-			buck1_reg: BUCK1 {
-				regulator-name = "VDD_MIF_0.9V_AP";
-				regulator-min-microvolt = <600000>;
-				regulator-max-microvolt = <1500000>;
-				regulator-always-on;
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			buck2_reg: BUCK2 {
-				regulator-name = "VDD_EGL_1.0V_AP";
-				regulator-min-microvolt = <900000>;
-				regulator-max-microvolt = <1300000>;
-				regulator-always-on;
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			buck3_reg: BUCK3 {
-				regulator-name = "VDD_KFC_1.0V_AP";
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <1200000>;
-				regulator-always-on;
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			buck4_reg: BUCK4 {
-				regulator-name = "VDD_INT_0.95V_AP";
-				regulator-min-microvolt = <600000>;
-				regulator-max-microvolt = <1500000>;
-				regulator-always-on;
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			buck5_reg: BUCK5 {
-				regulator-name = "VDD_DISP_CAM0_0.9V_AP";
-				regulator-min-microvolt = <600000>;
-				regulator-max-microvolt = <1500000>;
-				regulator-always-on;
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			buck6_reg: BUCK6 {
-				regulator-name = "VDD_G3D_0.9V_AP";
-				regulator-min-microvolt = <600000>;
-				regulator-max-microvolt = <1500000>;
-				regulator-always-on;
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			buck7_reg: BUCK7 {
-				regulator-name = "VDD_MEM1_1.2V_AP";
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <1200000>;
-				regulator-always-on;
-			};
-
-			buck8_reg: BUCK8 {
-				regulator-name = "VDD_LLDO_1.35V_AP";
-				regulator-min-microvolt = <1350000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-always-on;
-			};
-
-			buck9_reg: BUCK9 {
-				regulator-name = "VDD_MLDO_2.0V_AP";
-				regulator-min-microvolt = <1350000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-always-on;
-			};
-
-			buck10_reg: BUCK10 {
-				regulator-name = "vdd_mem2";
-				regulator-min-microvolt = <550000>;
-				regulator-max-microvolt = <1500000>;
-				regulator-always-on;
-			};
-		};
-	};
 };

-&hsi2c_8 {
+&hsi2c_9 {
 	status = "okay";

-	max77843@66 {
-		compatible = "maxim,max77843";
-		interrupt-parent = <&gpa1>;
-		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
-		reg = <0x66>;
-
-		muic: max77843-muic {
-			compatible = "maxim,max77843-muic";
-		};
-
-		regulators {
-			compatible = "maxim,max77843-regulator";
-			safeout1_reg: SAFEOUT1 {
-				regulator-name = "SAFEOUT1";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <4950000>;
-			};
-
-			safeout2_reg: SAFEOUT2 {
-				regulator-name = "SAFEOUT2";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <4950000>;
-			};
-
-			charger_reg: CHARGER {
-				regulator-name = "CHARGER";
-				regulator-min-microamp = <100000>;
-				regulator-max-microamp = <3150000>;
-			};
-		};
-
-		haptic: max77843-haptic {
-			compatible = "maxim,max77843-haptic";
-			haptic-supply = <&ldo38_reg>;
-			pwms = <&pwm 0 33670 0>;
-			pwm-names = "haptic";
-		};
+	touchkey@20 {
+		compatible = "cypress,tm2-touchkey";
+		reg = <0x20>;
+		interrupt-parent = <&gpa3>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+		vcc-supply = <&ldo32_reg>;
+		vdd-supply = <&ldo33_reg>;
 	};
 };

-&i2s0 {
-	status = "okay";
-};
-
-&mshc_0 {
-	status = "okay";
-	num-slots = <1>;
-	mmc-hs200-1_8v;
-	mmc-hs400-1_8v;
-	cap-mmc-highspeed;
-	non-removable;
-	card-detect-delay = <200>;
-	samsung,dw-mshc-ciu-div = <3>;
-	samsung,dw-mshc-sdr-timing = <0 4>;
-	samsung,dw-mshc-ddr-timing = <0 2>;
-	samsung,dw-mshc-hs400-timing = <0 3>;
-	samsung,read-strobe-delay = <90>;
-	fifo-depth = <0x80>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_qrdy &sd0_bus1 &sd0_bus4
-			&sd0_bus8 &sd0_rdqs>;
-	bus-width = <8>;
-	assigned-clocks = <&cmu_top CLK_SCLK_MMC0_FSYS>;
-	assigned-clock-rates = <800000000>;
-};
-
-&mshc_2 {
-	status = "okay";
-	num-slots = <1>;
-	cap-sd-highspeed;
-	disable-wp;
-	cd-gpios = <&gpa2 4 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
-	card-detect-delay = <200>;
-	samsung,dw-mshc-ciu-div = <3>;
-	samsung,dw-mshc-sdr-timing = <0 4>;
-	samsung,dw-mshc-ddr-timing = <0 2>;
-	fifo-depth = <0x80>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus1 &sd2_bus4>;
-	bus-width = <4>;
-};
-
-&pinctrl_alive {
-	pinctrl-names = "default";
-	pinctrl-0 = <&initial_alive>;
-
-	initial_alive: initial-state {
-		PIN(IN, gpa0-0, DOWN, LV1);
-		PIN(IN, gpa0-1, NONE, LV1);
-		PIN(IN, gpa0-2, DOWN, LV1);
-		PIN(IN, gpa0-3, NONE, LV1);
-		PIN(IN, gpa0-4, NONE, LV1);
-		PIN(IN, gpa0-5, DOWN, LV1);
-		PIN(IN, gpa0-6, NONE, LV1);
-		PIN(IN, gpa0-7, NONE, LV1);
-
-		PIN(IN, gpa1-0, UP, LV1);
-		PIN(IN, gpa1-1, NONE, LV1);
-		PIN(IN, gpa1-2, NONE, LV1);
-		PIN(IN, gpa1-3, DOWN, LV1);
-		PIN(IN, gpa1-4, DOWN, LV1);
-		PIN(IN, gpa1-5, NONE, LV1);
-		PIN(IN, gpa1-6, NONE, LV1);
-		PIN(IN, gpa1-7, NONE, LV1);
-
-		PIN(IN, gpa2-0, NONE, LV1);
-		PIN(IN, gpa2-1, NONE, LV1);
-		PIN(IN, gpa2-2, NONE, LV1);
-		PIN(IN, gpa2-3, DOWN, LV1);
-		PIN(IN, gpa2-4, NONE, LV1);
-		PIN(IN, gpa2-5, DOWN, LV1);
-		PIN(IN, gpa2-6, DOWN, LV1);
-		PIN(IN, gpa2-7, NONE, LV1);
-
-		PIN(IN, gpa3-0, DOWN, LV1);
-		PIN(IN, gpa3-1, DOWN, LV1);
-		PIN(IN, gpa3-2, NONE, LV1);
-		PIN(IN, gpa3-3, DOWN, LV1);
-		PIN(IN, gpa3-4, NONE, LV1);
-		PIN(IN, gpa3-5, DOWN, LV1);
-		PIN(IN, gpa3-6, DOWN, LV1);
-		PIN(IN, gpa3-7, DOWN, LV1);
-
-		PIN(IN, gpf1-0, NONE, LV1);
-		PIN(IN, gpf1-1, NONE, LV1);
-		PIN(IN, gpf1-2, DOWN, LV1);
-		PIN(IN, gpf1-4, UP, LV1);
-		PIN(OUT, gpf1-5, NONE, LV1);
-		PIN(IN, gpf1-6, DOWN, LV1);
-		PIN(IN, gpf1-7, DOWN, LV1);
-
-		PIN(IN, gpf2-0, DOWN, LV1);
-		PIN(IN, gpf2-1, DOWN, LV1);
-		PIN(IN, gpf2-2, DOWN, LV1);
-		PIN(IN, gpf2-3, DOWN, LV1);
-
-		PIN(IN, gpf3-0, DOWN, LV1);
-		PIN(IN, gpf3-1, DOWN, LV1);
-		PIN(IN, gpf3-2, NONE, LV1);
-		PIN(IN, gpf3-3, DOWN, LV1);
-
-		PIN(IN, gpf4-0, DOWN, LV1);
-		PIN(IN, gpf4-1, DOWN, LV1);
-		PIN(IN, gpf4-2, DOWN, LV1);
-		PIN(IN, gpf4-3, DOWN, LV1);
-		PIN(IN, gpf4-4, DOWN, LV1);
-		PIN(IN, gpf4-5, DOWN, LV1);
-		PIN(IN, gpf4-6, DOWN, LV1);
-		PIN(IN, gpf4-7, DOWN, LV1);
-
-		PIN(IN, gpf5-0, DOWN, LV1);
-		PIN(IN, gpf5-1, DOWN, LV1);
-		PIN(IN, gpf5-2, DOWN, LV1);
-		PIN(IN, gpf5-3, DOWN, LV1);
-		PIN(OUT, gpf5-4, NONE, LV1);
-		PIN(IN, gpf5-5, DOWN, LV1);
-		PIN(IN, gpf5-6, DOWN, LV1);
-		PIN(IN, gpf5-7, DOWN, LV1);
-	};
-
-	te_irq: te_irq {
-		samsung,pins = "gpf1-3";
-		samsung,pin-function = <0xf>;
-	};
-};
-
-&pinctrl_cpif {
-	pinctrl-names = "default";
-	pinctrl-0 = <&initial_cpif>;
-
-	initial_cpif: initial-state {
-		PIN(IN, gpv6-0, DOWN, LV1);
-		PIN(IN, gpv6-1, DOWN, LV1);
-	};
-};
-
-&pinctrl_ese {
-	pinctrl-names = "default";
-	pinctrl-0 = <&initial_ese>;
-
-	initial_ese: initial-state {
-		PIN(IN, gpj2-0, DOWN, LV1);
-		PIN(IN, gpj2-1, DOWN, LV1);
-		PIN(IN, gpj2-2, DOWN, LV1);
-	};
-};
-
-&pinctrl_fsys {
-	pinctrl-names = "default";
-	pinctrl-0 = <&initial_fsys>;
-
-	initial_fsys: initial-state {
-		PIN(IN, gpr3-0, NONE, LV1);
-		PIN(IN, gpr3-1, DOWN, LV1);
-		PIN(IN, gpr3-2, DOWN, LV1);
-		PIN(IN, gpr3-3, DOWN, LV1);
-		PIN(IN, gpr3-7, NONE, LV1);
-	};
-};
-
-&pinctrl_imem {
-	pinctrl-names = "default";
-	pinctrl-0 = <&initial_imem>;
-
-	initial_imem: initial-state {
-		PIN(IN, gpf0-0, UP, LV1);
-		PIN(IN, gpf0-1, UP, LV1);
-		PIN(IN, gpf0-2, DOWN, LV1);
-		PIN(IN, gpf0-3, UP, LV1);
-		PIN(IN, gpf0-4, DOWN, LV1);
-		PIN(IN, gpf0-5, NONE, LV1);
-		PIN(IN, gpf0-6, DOWN, LV1);
-		PIN(IN, gpf0-7, UP, LV1);
-	};
-};
-
-&pinctrl_nfc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&initial_nfc>;
-
-	initial_nfc: initial-state {
-		PIN(IN, gpj0-2, DOWN, LV1);
-	};
-};
-
-&pinctrl_peric {
-	pinctrl-names = "default";
-	pinctrl-0 = <&initial_peric>;
-
-	initial_peric: initial-state {
-		PIN(IN, gpv7-0, DOWN, LV1);
-		PIN(IN, gpv7-1, DOWN, LV1);
-		PIN(IN, gpv7-2, NONE, LV1);
-		PIN(IN, gpv7-3, DOWN, LV1);
-		PIN(IN, gpv7-4, DOWN, LV1);
-		PIN(IN, gpv7-5, DOWN, LV1);
-
-		PIN(IN, gpb0-4, DOWN, LV1);
-
-		PIN(IN, gpc0-2, DOWN, LV1);
-		PIN(IN, gpc0-5, DOWN, LV1);
-		PIN(IN, gpc0-7, DOWN, LV1);
-
-		PIN(IN, gpc1-1, DOWN, LV1);
-
-		PIN(IN, gpc3-4, NONE, LV1);
-		PIN(IN, gpc3-5, NONE, LV1);
-		PIN(IN, gpc3-6, NONE, LV1);
-		PIN(IN, gpc3-7, NONE, LV1);
-
-		PIN(OUT, gpg0-0, NONE, LV1);
-		PIN(FUNC1, gpg0-1, DOWN, LV1);
-
-		PIN(IN, gpd2-5, DOWN, LV1);
-
-		PIN(IN, gpd4-0, NONE, LV1);
-		PIN(IN, gpd4-1, DOWN, LV1);
-		PIN(IN, gpd4-2, DOWN, LV1);
-		PIN(IN, gpd4-3, DOWN, LV1);
-		PIN(IN, gpd4-4, DOWN, LV1);
-
-		PIN(IN, gpd6-3, DOWN, LV1);
-
-		PIN(IN, gpd8-1, UP, LV1);
-
-		PIN(IN, gpg1-0, DOWN, LV1);
-		PIN(IN, gpg1-1, DOWN, LV1);
-		PIN(IN, gpg1-2, DOWN, LV1);
-		PIN(IN, gpg1-3, DOWN, LV1);
-		PIN(IN, gpg1-4, DOWN, LV1);
-
-		PIN(IN, gpg2-0, DOWN, LV1);
-		PIN(IN, gpg2-1, DOWN, LV1);
-
-		PIN(IN, gpg3-0, DOWN, LV1);
-		PIN(IN, gpg3-1, DOWN, LV1);
-		PIN(IN, gpg3-5, DOWN, LV1);
-		PIN(IN, gpg3-7, DOWN, LV1);
-	};
-};
-
-&pinctrl_touch {
-	pinctrl-names = "default";
-	pinctrl-0 = <&initial_touch>;
-
-	initial_touch: initial-state {
-		PIN(IN, gpj1-2, DOWN, LV1);
-	};
-};
-
-&pwm {
-	pinctrl-0 = <&pwm0_out>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&mic {
-	status = "okay";
-
-	i80-if-timings {
-	};
-};
-
-&pmu_system_controller {
-	assigned-clocks = <&pmu_system_controller 0>;
-	assigned-clock-parents = <&xxti>;
-};
-
-&serial_1 {
-	status = "okay";
-};
-
-&spi_1 {
-	cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>;
-	status = "okay";
-
-	wm5110: wm5110-codec@0 {
-		compatible = "wlf,wm5110";
-		reg = <0x0>;
-		spi-max-frequency = <20000000>;
-		interrupt-parent = <&gpa0>;
-		interrupts = <4 IRQ_TYPE_NONE>;
-		clocks = <&pmu_system_controller 0>,
-			<&s2mps13_osc S2MPS11_CLK_BT>;
-		clock-names = "mclk1", "mclk2";
-
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		wlf,micd-detect-debounce = <300>;
-		wlf,micd-bias-start-time = <0x1>;
-		wlf,micd-rate = <0x7>;
-		wlf,micd-dbtime = <0x1>;
-		wlf,micd-force-micbias;
-		wlf,micd-configs = <0x0 1 0>;
-		wlf,hpdet-channel = <1>;
-		wlf,gpsw = <0x1>;
-		wlf,inmode = <2 0 2 0>;
-
-		wlf,reset = <&gpc0 7 GPIO_ACTIVE_HIGH>;
-		wlf,ldoena = <&gpf0 0 GPIO_ACTIVE_HIGH>;
-
-		/* core supplies */
-		AVDD-supply = <&ldo18_reg>;
-		DBVDD1-supply = <&ldo18_reg>;
-		CPVDD-supply = <&ldo18_reg>;
-		DBVDD2-supply = <&ldo18_reg>;
-		DBVDD3-supply = <&ldo18_reg>;
-
-		controller-data {
-			samsung,spi-feedback-delay = <0>;
-		};
-	};
-};
-
-&timer {
-	clock-frequency = <24000000>;
-};
-
-&tmu_atlas0 {
-	vtmu-supply = <&ldo3_reg>;
-	status = "okay";
-};
-
-&tmu_apollo {
-	vtmu-supply = <&ldo3_reg>;
-	status = "okay";
-};
-
-&tmu_g3d {
-	vtmu-supply = <&ldo3_reg>;
-	status = "okay";
-};
-
-&usbdrd30 {
-	vdd33-supply = <&ldo10_reg>;
-	vdd10-supply = <&ldo6_reg>;
-	status = "okay";
-};
-
-&usbdrd_dwc3_0 {
-	dr_mode = "otg";
-};
-
-&usbdrd30_phy {
-	vbus-supply = <&safeout1_reg>;
-	status = "okay";
+&ldo31_reg {
+	regulator-name = "TSP_VDD_1.85V_AP";
+	regulator-min-microvolt = <1850000>;
+	regulator-max-microvolt = <1850000>;
 };

-&xxti {
-	clock-frequency = <24000000>;
+&ldo38_reg {
+	regulator-name = "VCC_3.0V_MOTOR_AP";
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
 };
--- a/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts
@@ -11,23 +11,13 @@
 * published by the Free Software Foundation.
 */

-#include "exynos5433-tm2.dts"
+#include "exynos5433-tm2-common.dtsi"

 / {
 	model = "Samsung TM2E board";
 	compatible = "samsung,tm2e", "samsung,exynos5433";
 };

-&ldo23_reg {
-	regulator-name = "CAM_SEN_CORE_1.025V_AP";
-	regulator-max-microvolt = <1050000>;
-};
-
-&ldo25_reg {
-	regulator-name = "UNUSED_LDO25";
-	regulator-always-off;
-};
-
 &ldo31_reg {
 	regulator-name = "TSP_VDD_1.8V_AP";
 	regulator-min-microvolt = <1800000>;

--- a/arch/arm64/boot/dts/exynos/exynos5433.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos5433.dtsi
@@ -299,7 +299,7 @@ cmu_peric: clock-controller@14c80000 {
 			#clock-cells = <1>;
 		};

-		cmu_peris: clock-controller@0x10040000 {
+		cmu_peris: clock-controller@10040000 {
 			compatible = "samsung,exynos5433-cmu-peris";
 			reg = <0x10040000 0x1000>;
 			#clock-cells = <1>;
@@ -599,6 +599,30 @@ mct@101c0000 {
 			clock-names = "fin_pll", "mct";
 		};

+		ppmu_d0_cpu: ppmu@10480000 {
+			compatible = "samsung,exynos-ppmu-v2";
+			reg = <0x10480000 0x2000>;
+			status = "disabled";
+		};
+
+		ppmu_d0_general: ppmu@10490000 {
+			compatible = "samsung,exynos-ppmu-v2";
+			reg = <0x10490000 0x2000>;
+			status = "disabled";
+		};
+
+		ppmu_d1_cpu: ppmu@104b0000 {
+			compatible = "samsung,exynos-ppmu-v2";
+			reg = <0x104b0000 0x2000>;
+			status = "disabled";
+		};
+
+		ppmu_d1_general: ppmu@104c0000 {
+			compatible = "samsung,exynos-ppmu-v2";
+			reg = <0x104c0000 0x2000>;
+			status = "disabled";
+		};
+
 		pinctrl_alive: pinctrl@10580000 {
 			compatible = "samsung,exynos5433-pinctrl";
 			reg = <0x10580000 0x1a20>, <0x11090000 0x100>;
@@ -682,7 +706,7 @@ gic: interrupt-controller@11001000 {
 			interrupts = <GIC_PPI 9 0xf04>;
 		};

-		mipi_phy: video-phy@105c0710 {
+		mipi_phy: video-phy {
 			compatible = "samsung,exynos5433-mipi-video-phy";
 			#phy-cells = <1>;
 			samsung,pmu-syscon = <&pmu_system_controller>;
@@ -727,6 +751,29 @@ decon_to_mic: endpoint {
 			};
 		};

+		decon_tv: decon@13880000 {
+			compatible = "samsung,exynos5433-decon-tv";
+			reg = <0x13880000 0x20b8>;
+			clocks = <&cmu_disp CLK_PCLK_DECON_TV>,
+				 <&cmu_disp CLK_ACLK_DECON_TV>,
+				 <&cmu_disp CLK_ACLK_SMMU_TV0X>,
+				 <&cmu_disp CLK_ACLK_XIU_TV0X>,
+				 <&cmu_disp CLK_PCLK_SMMU_TV0X>,
+				 <&cmu_disp CLK_SCLK_DECON_TV_VCLK>,
+				 <&cmu_disp CLK_SCLK_DECON_TV_ECLK>;
+			clock-names = "pclk", "aclk_decon", "aclk_smmu_decon0x",
+				      "aclk_xiu_decon0x", "pclk_smmu_decon0x",
+				      "sclk_decon_vclk", "sclk_decon_eclk";
+			samsung,disp-sysreg = <&syscon_disp>;
+			interrupt-names = "fifo", "vsync", "lcd_sys";
+			interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			iommus = <&sysmmu_tv0x>, <&sysmmu_tv1x>;
+			iommu-names = "m0", "m1";
+		};
+
 		dsi: dsi@13900000 {
 			compatible = "samsung,exynos5433-mipi-dsi";
 			reg = <0x13900000 0xC0>;
@@ -790,6 +837,35 @@ mic_to_dsi: endpoint {
 			};
 		};

+		hdmi: hdmi@13970000 {
+			compatible = "samsung,exynos5433-hdmi";
+			reg = <0x13970000 0x70000>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu_disp CLK_PCLK_HDMI>,
+				<&cmu_disp CLK_PCLK_HDMIPHY>,
+				<&cmu_disp CLK_PHYCLK_HDMIPHY_TMDS_CLKO>,
+				<&cmu_disp CLK_PHYCLK_HDMI_PIXEL>,
+				<&cmu_disp CLK_PHYCLK_HDMIPHY_TMDS_CLKO_PHY>,
+				<&cmu_disp CLK_MOUT_PHYCLK_HDMIPHY_TMDS_CLKO_USER>,
+				<&cmu_disp CLK_PHYCLK_HDMIPHY_PIXEL_CLKO_PHY>,
+				<&cmu_disp CLK_MOUT_PHYCLK_HDMIPHY_PIXEL_CLKO_USER>,
+				<&xxti>, <&cmu_disp CLK_SCLK_HDMI_SPDIF>;
+			clock-names = "hdmi_pclk", "hdmi_i_pclk",
+				"i_tmds_clk", "i_pixel_clk",
+				"tmds_clko", "tmds_clko_user",
+				"pixel_clko", "pixel_clko_user",
+				"oscclk", "i_spdif_clk";
+			phy = <&hdmiphy>;
+			ddc = <&hsi2c_11>;
+			samsung,syscon-phandle = <&pmu_system_controller>;
+			samsung,sysreg-phandle = <&syscon_disp>;
+			status = "disabled";
+		};
+
+		hdmiphy: hdmiphy@13af0000 {
+			reg = <0x13af0000 0x80>;
+		};
+
 		syscon_disp: syscon@13b80000 {
 			compatible = "syscon";
 			reg = <0x13b80000 0x1010>;
@@ -868,7 +944,7 @@ mfc: codec@152E0000 {
 			iommu-names = "left", "right";
 		};

-		sysmmu_decon0x: sysmmu@0x13a00000 {
+		sysmmu_decon0x: sysmmu@13a00000 {
 			compatible = "samsung,exynos-sysmmu";
 			reg = <0x13a00000 0x1000>;
 			interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
@@ -878,7 +954,7 @@ sysmmu_decon0x: sysmmu@0x13a00000 {
 			#iommu-cells = <0>;
 		};

-		sysmmu_decon1x: sysmmu@0x13a10000 {
+		sysmmu_decon1x: sysmmu@13a10000 {
 			compatible = "samsung,exynos-sysmmu";
 			reg = <0x13a10000 0x1000>;
 			interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
@@ -888,7 +964,27 @@ sysmmu_decon1x: sysmmu@0x13a10000 {
 			#iommu-cells = <0>;
 		};

-		sysmmu_gscl0: sysmmu@0x13C80000 {
+		sysmmu_tv0x: sysmmu@13a20000 {
+			compatible = "samsung,exynos-sysmmu";
+			reg = <0x13a20000 0x1000>;
+			interrupts = <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "pclk", "aclk";
+			clocks = <&cmu_disp CLK_PCLK_SMMU_TV0X>,
+				<&cmu_disp CLK_ACLK_SMMU_TV0X>;
+			#iommu-cells = <0>;
+		};
+
+		sysmmu_tv1x: sysmmu@13a30000 {
+			compatible = "samsung,exynos-sysmmu";
+			reg = <0x13a30000 0x1000>;
+			interrupts = <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "pclk", "aclk";
+			clocks = <&cmu_disp CLK_PCLK_SMMU_TV1X>,
+				<&cmu_disp CLK_ACLK_SMMU_TV1X>;
+			#iommu-cells = <0>;
+		};
+
+		sysmmu_gscl0: sysmmu@13c80000 {
 			compatible = "samsung,exynos-sysmmu";
 			reg = <0x13C80000 0x1000>;
 			interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
@@ -898,7 +994,7 @@ sysmmu_gscl0: sysmmu@0x13C80000 {
 			#iommu-cells = <0>;
 		};

-		sysmmu_gscl1: sysmmu@0x13C90000 {
+		sysmmu_gscl1: sysmmu@13c90000 {
 			compatible = "samsung,exynos-sysmmu";
 			reg = <0x13C90000 0x1000>;
 			interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
@@ -908,7 +1004,7 @@ sysmmu_gscl1: sysmmu@0x13C90000 {
 			#iommu-cells = <0>;
 		};

-		sysmmu_gscl2: sysmmu@0x13CA0000 {
+		sysmmu_gscl2: sysmmu@13ca0000 {
 			compatible = "samsung,exynos-sysmmu";
 			reg = <0x13CA0000 0x1000>;
 			interrupts = <GIC_SPI 292 IRQ_TYPE_LEVEL_HIGH>;
@@ -918,7 +1014,7 @@ sysmmu_gscl2: sysmmu@0x13CA0000 {
 			#iommu-cells = <0>;
 		};

-		sysmmu_jpeg: sysmmu@0x15060000 {
+		sysmmu_jpeg: sysmmu@15060000 {
 			compatible = "samsung,exynos-sysmmu";
 			reg = <0x15060000 0x1000>;
 			interrupts = <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>;
@@ -928,7 +1024,7 @@ sysmmu_jpeg: sysmmu@0x15060000 {
 			#iommu-cells = <0>;
 		};

-		sysmmu_mfc_0: sysmmu@0x15200000 {
+		sysmmu_mfc_0: sysmmu@15200000 {
 			compatible = "samsung,exynos-sysmmu";
 			reg = <0x15200000 0x1000>;
 			interrupts = <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
@@ -938,7 +1034,7 @@ sysmmu_mfc_0: sysmmu@0x15200000 {
 			#iommu-cells = <0>;
 		};

-		sysmmu_mfc_1: sysmmu@0x15210000 {
+		sysmmu_mfc_1: sysmmu@15210000 {
 			compatible = "samsung,exynos-sysmmu";
 			reg = <0x15210000 0x1000>;
 			interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
@@ -1261,7 +1357,7 @@ hsi2c_11: hsi2c@14df0000 {
 			status = "disabled";
 		};

-		usbdrd30: usb@15400000  {
+		usbdrd30: usbdrd {
 			compatible = "samsung,exynos5250-dwusb3";
 			clocks = <&cmu_fsys CLK_ACLK_USBDRD30>,
 				<&cmu_fsys CLK_SCLK_USBDRD30>;
@@ -1308,7 +1404,7 @@ usbhost30_phy: phy@15580000 {
 			status = "disabled";
 		};

-		usbhost30: usb@15a00000 {
+		usbhost30: usbhost {
 			compatible = "samsung,exynos5250-dwusb3";
 			clocks = <&cmu_fsys CLK_ACLK_USBHOST30>,
 				<&cmu_fsys CLK_SCLK_USBHOST30>;
@@ -1398,6 +1494,8 @@ pdma1: pdma@15600000 {
 		audio-subsystem@11400000 {
 			compatible = "samsung,exynos5433-lpass";
 			reg = <0x11400000 0x100>, <0x11500000 0x08>;
+			clocks = <&cmu_aud CLK_PCLK_SFR0_CTRL>;
+			clock-names = "sfr0_ctrl";
 			samsung,pmu-syscon = <&pmu_system_controller>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -1458,5 +1556,6 @@ timer: timer {
 	};
 };

+#include "exynos5433-bus.dtsi"
 #include "exynos5433-pinctrl.dtsi"
 #include "exynos5433-tmu.dtsi"
--- a/arch/arm64/boot/dts/exynos/exynos7-pinctrl.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos7-pinctrl.dtsi
@@ -497,49 +497,49 @@ sd0_clk: sd0-clk {
 		samsung,pins = "gpr0-0";
 		samsung,pin-function = <2>;
 		samsung,pin-pud = <0>;
-		samsung,pin-drv = <3>;
+		samsung,pin-drv = <4>;
 	};

 	sd0_cmd: sd0-cmd {
 		samsung,pins = "gpr0-1";
 		samsung,pin-function = <2>;
 		samsung,pin-pud = <3>;
-		samsung,pin-drv = <3>;
+		samsung,pin-drv = <4>;
 	};

 	sd0_ds: sd0-ds {
 		samsung,pins = "gpr0-2";
 		samsung,pin-function = <2>;
 		samsung,pin-pud = <1>;
-		samsung,pin-drv = <3>;
+		samsung,pin-drv = <4>;
 	};

 	sd0_qrdy: sd0-qrdy {
 		samsung,pins = "gpr0-3";
 		samsung,pin-function = <2>;
 		samsung,pin-pud = <1>;
-		samsung,pin-drv = <3>;
+		samsung,pin-drv = <4>;
 	};

 	sd0_bus1: sd0-bus-width1 {
 		samsung,pins = "gpr1-0";
 		samsung,pin-function = <2>;
 		samsung,pin-pud = <3>;
-		samsung,pin-drv = <3>;
+		samsung,pin-drv = <4>;
 	};

 	sd0_bus4: sd0-bus-width4 {
 		samsung,pins = "gpr1-1", "gpr1-2", "gpr1-3";
 		samsung,pin-function = <2>;
 		samsung,pin-pud = <3>;
-		samsung,pin-drv = <3>;
+		samsung,pin-drv = <4>;
 	};

 	sd0_bus8: sd0-bus-width8 {
 		samsung,pins = "gpr1-4", "gpr1-5", "gpr1-6", "gpr1-7";
 		samsung,pin-function = <2>;
 		samsung,pin-pud = <3>;
-		samsung,pin-drv = <3>;
+		samsung,pin-drv = <4>;
 	};

 	sd1_clk: sd1-clk {

--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-frdm.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-qds.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb

--- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts
+/*
+ * Device Tree file for Freescale LS1012A Freedom Board.
+ *
+ * Copyright 2016, Freescale Semiconductor
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "fsl-ls1012a.dtsi"
+
+/ {
+	model = "LS1012A Freedom Board";
+	compatible = "fsl,ls1012a-frdm", "fsl,ls1012a";
+
+	sys_mclk: clock-mclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Headphone", "Headphone Jack",
+			"Speaker", "Speaker Ext",
+			"Line", "Line In Jack";
+		simple-audio-card,routing =
+			"MIC_IN", "Microphone Jack",
+			"Microphone Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"Speaker Ext", "LINE_OUT";
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+			frame-master;
+			bitclock-master;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&codec>;
+			frame-master;
+			bitclock-master;
+			system-clock-frequency = <25000000>;
+		};
+	};
+};
+
+&duart0 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	codec: sgtl5000@a {
+		#sound-dai-cells = <0>;
+		compatible = "fsl,sgtl5000";
+		reg = <0xa>;
+		VDDA-supply = <&reg_1p8v>;
+		VDDIO-supply = <&reg_1p8v>;
+		clocks = <&sys_mclk>;
+	};
+};
+
+&sai2 {
+	status = "okay";
+};
--- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
+/*
+ * Device Tree file for Freescale LS1012A QDS Board.
+ *
+ * Copyright 2016, Freescale Semiconductor
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "fsl-ls1012a.dtsi"
+
+/ {
+	model = "LS1012A QDS Board";
+	compatible = "fsl,ls1012a-qds", "fsl,ls1012a";
+
+	sys_mclk: clock-mclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Headphone", "Headphone Jack",
+			"Speaker", "Speaker Ext",
+			"Line", "Line In Jack";
+		simple-audio-card,routing =
+			"MIC_IN", "Microphone Jack",
+			"Microphone Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"Speaker Ext", "LINE_OUT";
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+			frame-master;
+			bitclock-master;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&codec>;
+			frame-master;
+			bitclock-master;
+			system-clock-frequency = <24576000>;
+		};
+	};
+};
+
+&duart0 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	pca9547@77 {
+		compatible = "nxp,pca9547";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+
+			codec: sgtl5000@a {
+				#sound-dai-cells = <0>;
+				compatible = "fsl,sgtl5000";
+				reg = <0xa>;
+				VDDA-supply = <&reg_3p3v>;
+				VDDIO-supply = <&reg_3p3v>;
+				clocks = <&sys_mclk>;
+			};
+		};
+	};
+};
+
+&sai2 {
+	status = "okay";
+};
--- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
+/*
+ * Device Tree file for Freescale LS1012A RDB Board.
+ *
+ * Copyright 2016, Freescale Semiconductor
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "fsl-ls1012a.dtsi"
+
+/ {
+	model = "LS1012A RDB Board";
+	compatible = "fsl,ls1012a-rdb", "fsl,ls1012a";
+};
+
+&duart0 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+};
--- a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
+/*
+ * Device Tree Include file for Freescale Layerscape-1012A family SoC.
+ *
+ * Copyright 2016, Freescale Semiconductor
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "fsl,ls1012a";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			clocks = <&clockgen 1 0>;
+			#cooling-cells = <2>;
+		};
+	};
+
+	sysclk: sysclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+		clock-output-names = "sysclk";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <1 13 IRQ_TYPE_LEVEL_LOW>,/* Physical Secure PPI */
+			     <1 14 IRQ_TYPE_LEVEL_LOW>,/* Physical Non-Secure PPI */
+			     <1 11 IRQ_TYPE_LEVEL_LOW>,/* Virtual PPI */
+			     <1 10 IRQ_TYPE_LEVEL_LOW>;/* Hypervisor PPI */
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <0 106 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gic: interrupt-controller@1400000 {
+		compatible = "arm,gic-400";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0x0 0x1401000 0 0x1000>, /* GICD */
+		      <0x0 0x1402000 0 0x2000>, /* GICC */
+		      <0x0 0x1404000 0 0x2000>, /* GICH */
+		      <0x0 0x1406000 0 0x2000>; /* GICV */
+		interrupts = <1 9 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	reboot {
+		compatible = "syscon-reboot";
+		regmap = <&dcfg>;
+		offset = <0xb0>;
+		mask = <0x02>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		scfg: scfg@1570000 {
+			compatible = "fsl,ls1012a-scfg", "syscon";
+			reg = <0x0 0x1570000 0x0 0x10000>;
+			big-endian;
+		};
+
+		dcfg: dcfg@1ee0000 {
+			compatible = "fsl,ls1012a-dcfg",
+				     "syscon";
+			reg = <0x0 0x1ee0000 0x0 0x10000>;
+			big-endian;
+		};
+
+		clockgen: clocking@1ee1000 {
+			compatible = "fsl,ls1012a-clockgen";
+			reg = <0x0 0x1ee1000 0x0 0x1000>;
+			#clock-cells = <2>;
+			clocks = <&sysclk>;
+		};
+
+		i2c0: i2c@2180000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2180000 0x0 0x10000>;
+			interrupts = <0 56 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 0>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@2190000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2190000 0x0 0x10000>;
+			interrupts = <0 57 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 0>;
+			status = "disabled";
+		};
+
+		duart0: serial@21c0500 {
+			compatible = "fsl,ns16550", "ns16550a";
+			reg = <0x00 0x21c0500 0x0 0x100>;
+			interrupts = <0 54 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 0>;
+			status = "disabled";
+		};
+
+		duart1: serial@21c0600 {
+			compatible = "fsl,ns16550", "ns16550a";
+			reg = <0x00 0x21c0600 0x0 0x100>;
+			interrupts = <0 54 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 0>;
+			status = "disabled";
+		};
+
+		gpio0: gpio@2300000 {
+			compatible = "fsl,qoriq-gpio";
+			reg = <0x0 0x2300000 0x0 0x10000>;
+			interrupts = <0 66 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio1: gpio@2310000 {
+			compatible = "fsl,qoriq-gpio";
+			reg = <0x0 0x2310000 0x0 0x10000>;
+			interrupts = <0 67 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		wdog0: wdog@2ad0000 {
+			compatible = "fsl,ls1012a-wdt",
+				     "fsl,imx21-wdt";
+			reg = <0x0 0x2ad0000 0x0 0x10000>;
+			interrupts = <0 83 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 0>;
+			big-endian;
+		};
+
+		sai1: sai@2b50000 {
+			#sound-dai-cells = <0>;
+			compatible = "fsl,vf610-sai";
+			reg = <0x0 0x2b50000 0x0 0x10000>;
+			interrupts = <0 148 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 3>, <&clockgen 4 3>,
+				 <&clockgen 4 3>, <&clockgen 4 3>;
+			clock-names = "bus", "mclk1", "mclk2", "mclk3";
+			dma-names = "tx", "rx";
+			dmas = <&edma0 1 47>,
+			       <&edma0 1 46>;
+			status = "disabled";
+		};
+
+		sai2: sai@2b60000 {
+			#sound-dai-cells = <0>;
+			compatible = "fsl,vf610-sai";
+			reg = <0x0 0x2b60000 0x0 0x10000>;
+			interrupts = <0 149 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 3>, <&clockgen 4 3>,
+				 <&clockgen 4 3>, <&clockgen 4 3>;
+			clock-names = "bus", "mclk1", "mclk2", "mclk3";
+			dma-names = "tx", "rx";
+			dmas = <&edma0 1 45>,
+			       <&edma0 1 44>;
+			status = "disabled";
+		};
+
+		edma0: edma@2c00000 {
+			#dma-cells = <2>;
+			compatible = "fsl,vf610-edma";
+			reg = <0x0 0x2c00000 0x0 0x10000>,
+			      <0x0 0x2c10000 0x0 0x10000>,
+			      <0x0 0x2c20000 0x0 0x10000>;
+			interrupts = <0 103 IRQ_TYPE_LEVEL_HIGH>,
+				     <0 103 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "edma-tx", "edma-err";
+			dma-channels = <32>;
+			big-endian;
+			clock-names = "dmamux0", "dmamux1";
+			clocks = <&clockgen 4 3>,
+				 <&clockgen 4 3>;
+		};
+
+		sata: sata@3200000 {
+			compatible = "fsl,ls1012a-ahci", "fsl,ls1043a-ahci";
+			reg = <0x0 0x3200000 0x0 0x10000>;
+			interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 0>;
+			status = "disabled";
+		};
+	};
+};
--- a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
@@ -45,6 +45,7 @@
 */

 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>

 / {
 	compatible = "fsl,ls1046a";
@@ -67,6 +68,7 @@ cpu0: cpu@0 {
 			clocks = <&clockgen 1 0>;
 			next-level-cache = <&l2>;
 			cpu-idle-states = <&CPU_PH20>;
+			#cooling-cells = <2>;
 		};

 		cpu1: cpu@1 {
@@ -279,6 +281,84 @@ clockgen: clocking@1ee1000 {
 			clocks = <&sysclk>;
 		};

+		tmu: tmu@1f00000 {
+			compatible = "fsl,qoriq-tmu";
+			reg = <0x0 0x1f00000 0x0 0x10000>;
+			interrupts = <0 33 0x4>;
+			fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x30062>;
+			fsl,tmu-calibration =
+				/* Calibration data group 1 */
+				<0x00000000 0x00000026
+				0x00000001 0x0000002d
+				0x00000002 0x00000032
+				0x00000003 0x00000039
+				0x00000004 0x0000003f
+				0x00000005 0x00000046
+				0x00000006 0x0000004d
+				0x00000007 0x00000054
+				0x00000008 0x0000005a
+				0x00000009 0x00000061
+				0x0000000a 0x0000006a
+				0x0000000b 0x00000071
+				/* Calibration data group 2 */
+				0x00010000 0x00000025
+				0x00010001 0x0000002c
+				0x00010002 0x00000035
+				0x00010003 0x0000003d
+				0x00010004 0x00000045
+				0x00010005 0x0000004e
+				0x00010006 0x00000057
+				0x00010007 0x00000061
+				0x00010008 0x0000006b
+				0x00010009 0x00000076
+				/* Calibration data group 3 */
+				0x00020000 0x00000029
+				0x00020001 0x00000033
+				0x00020002 0x0000003d
+				0x00020003 0x00000049
+				0x00020004 0x00000056
+				0x00020005 0x00000061
+				0x00020006 0x0000006d
+				/* Calibration data group 4 */
+				0x00030000 0x00000021
+				0x00030001 0x0000002a
+				0x00030002 0x0000003c
+				0x00030003 0x0000004e>;
+			big-endian;
+			#thermal-sensor-cells = <1>;
+		};
+
+		thermal-zones {
+			cpu_thermal: cpu-thermal {
+				polling-delay-passive = <1000>;
+				polling-delay = <5000>;
+				thermal-sensors = <&tmu 3>;
+
+				trips {
+					cpu_alert: cpu-alert {
+						temperature = <85000>;
+						hysteresis = <2000>;
+						type = "passive";
+					};
+
+					cpu_crit: cpu-crit {
+						temperature = <95000>;
+						hysteresis = <2000>;
+						type = "critical";
+					};
+				};
+
+				cooling-maps {
+					map0 {
+						trip = <&cpu_alert>;
+						cooling-device =
+							<&cpu0 THERMAL_NO_LIMIT
+							THERMAL_NO_LIMIT>;
+					};
+				};
+			};
+		};
+
 		dspi: dspi@2100000 {
 			compatible = "fsl,ls1021a-v1.0-dspi";
 			#address-cells = <1>;

--- a/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts
@@ -102,7 +102,6 @@ pca9547@75 {
 		reg = <0x75>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		status = "disabled";
 		i2c@1 {
 			#address-cells = <1>;
 			#size-cells = <0>;

--- a/arch/arm64/boot/dts/hisilicon/Makefile
+++ b/arch/arm64/boot/dts/hisilicon/Makefile
+dtb-$(CONFIG_ARCH_HISI) += hi3660-hikey960.dtb
 dtb-$(CONFIG_ARCH_HISI) += hi6220-hikey.dtb
 dtb-$(CONFIG_ARCH_HISI) += hip05-d02.dtb
 dtb-$(CONFIG_ARCH_HISI) += hip06-d03.dtb

--- a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
+/*
+ * dts file for Hisilicon HiKey960 Development Board
+ *
+ * Copyright (C) 2016, Hisilicon Ltd.
+ *
+ */
+
+/dts-v1/;
+
+#include "hi3660.dtsi"
+
+/ {
+	model = "HiKey960";
+	compatible = "hisilicon,hi3660";
+
+	aliases {
+		serial5 = &uart5;       /* console UART */
+	};
+
+	chosen {
+		stdout-path = "serial5:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		/* rewrite this at bootloader */
+		reg = <0x0 0x0 0x0 0x0>;
+	};
+};
+
+&uart5 {
+	status = "okay";
+};
--- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
+/*
+ * dts file for Hisilicon Hi3660 SoC
+ *
+ * Copyright (C) 2016, Hisilicon Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "hisilicon,hi3660";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+				core2 {
+					cpu = <&cpu2>;
+				};
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+			cluster1 {
+				core0 {
+					cpu = <&cpu4>;
+				};
+				core1 {
+					cpu = <&cpu5>;
+				};
+				core2 {
+					cpu = <&cpu6>;
+				};
+				core3 {
+					cpu = <&cpu7>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a53", "arm,armv8";
+			device_type = "cpu";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a53", "arm,armv8";
+			device_type = "cpu";
+			reg = <0x0 0x1>;
+			enable-method = "psci";
+		};
+
+		cpu2: cpu@2 {
+			compatible = "arm,cortex-a53", "arm,armv8";
+			device_type = "cpu";
+			reg = <0x0 0x2>;
+			enable-method = "psci";
+		};
+
+		cpu3: cpu@3 {
+			compatible = "arm,cortex-a53", "arm,armv8";
+			device_type = "cpu";
+			reg = <0x0 0x3>;
+			enable-method = "psci";
+		};
+
+		cpu4: cpu@100 {
+			compatible = "arm,cortex-a73", "arm,armv8";
+			device_type = "cpu";
+			reg = <0x0 0x100>;
+			enable-method = "psci";
+		};
+
+		cpu5: cpu@101 {
+			compatible = "arm,cortex-a73", "arm,armv8";
+			device_type = "cpu";
+			reg = <0x0 0x101>;
+			enable-method = "psci";
+		};
+
+		cpu6: cpu@102 {
+			compatible = "arm,cortex-a73", "arm,armv8";
+			device_type = "cpu";
+			reg = <0x0 0x102>;
+			enable-method = "psci";
+		};
+
+		cpu7: cpu@103 {
+			compatible = "arm,cortex-a73", "arm,armv8";
+			device_type = "cpu";
+			reg = <0x0 0x103>;
+			enable-method = "psci";
+		};
+	};
+
+	gic: interrupt-controller@e82b0000 {
+		compatible = "arm,gic-400";
+		reg = <0x0 0xe82b1000 0 0x1000>, /* GICD */
+		      <0x0 0xe82b2000 0 0x2000>, /* GICC */
+		      <0x0 0xe82b4000 0 0x2000>, /* GICH */
+		      <0x0 0xe82b6000 0 0x2000>; /* GICV */
+		#address-cells = <0>;
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) |
+					 IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) |
+					  IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) |
+					  IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) |
+					  IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) |
+					  IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		fixed_uart5: fixed_19_2M {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
+			clock-output-names = "fixed:uart5";
+		};
+
+		uart5: uart@fdf05000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x0 0xfdf05000 0x0 0x1000>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&fixed_uart5 &fixed_uart5>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb

 always		:= $(dtb-y)
 subdir-y	:= $(dts-dirs)

--- a/arch/arm64/boot/dts/marvell/armada-371x.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-371x.dtsi
@@ -16,17 +16,17 @@
 *     published by the Free Software Foundation; either version 2 of the
 *     License, or (at your option) any later version.
 *
- *     This file is distributed in the hope that it will be useful
+ *     This file is distributed in the hope that it will be useful,
 *     but WITHOUT ANY WARRANTY; without even the implied warranty of
 *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *     GNU General Public License for more details.
 *
- * Or, alternatively
+ * Or, alternatively,
 *
 *  b) Permission is hereby granted, free of charge, to any person
 *     obtaining a copy of this software and associated documentation
 *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use
+ *     restriction, including without limitation the rights to use,
 *     copy, modify, merge, publish, distribute, sublicense, and/or
 *     sell copies of the Software, and to permit persons to whom the
 *     Software is furnished to do so, subject to the following
@@ -35,11 +35,11 @@
 *     The above copyright notice and this permission notice shall be
 *     included in all copies or substantial portions of the Software.
 *
- *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
 *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
 *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
 *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
 *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
 *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
 *     OTHER DEALINGS IN THE SOFTWARE.

--- a/arch/arm64/boot/dts/marvell/armada-3720-db.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-db.dts
@@ -15,17 +15,17 @@
 *     published by the Free Software Foundation; either version 2 of the
 *     License, or (at your option) any later version.
 *
- *     This file is distributed in the hope that it will be useful
+ *     This file is distributed in the hope that it will be useful,
 *     but WITHOUT ANY WARRANTY; without even the implied warranty of
 *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *     GNU General Public License for more details.
 *
- * Or, alternatively
+ * Or, alternatively,
 *
 *  b) Permission is hereby granted, free of charge, to any person
 *     obtaining a copy of this software and associated documentation
 *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use
+ *     restriction, including without limitation the rights to use,
 *     copy, modify, merge, publish, distribute, sublicense, and/or
 *     sell copies of the Software, and to permit persons to whom the
 *     Software is furnished to do so, subject to the following
@@ -34,11 +34,11 @@
 *     The above copyright notice and this permission notice shall be
 *     included in all copies or substantial portions of the Software.
 *
- *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
 *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
 *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
 *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
 *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
 *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
 *     OTHER DEALINGS IN THE SOFTWARE.
@@ -62,11 +62,45 @@ memory@0 {
 	};
 };

+&i2c0 {
+	status = "okay";
+};
+
 /* CON3 */
 &sata {
 	status = "okay";
 };

+&spi0 {
+	status = "okay";
+
+	m25p80@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <108000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			partition@0 {
+				label = "bootloader";
+				reg = <0x0 0x200000>;
+			};
+			partition@200000 {
+				label = "U-boot Env";
+				reg = <0x200000 0x10000>;
+			};
+			partition@210000 {
+				label = "Linux";
+				reg = <0x210000 0xDF0000>;
+			};
+		};
+	};
+};
+
 /* Exported on the micro USB connector CON32 through an FTDI */
 &uart0 {
 	status = "okay";

--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
@@ -14,17 +14,17 @@
 *     published by the Free Software Foundation; either version 2 of the
 *     License, or (at your option) any later version.
 *
- *     This file is distributed in the hope that it will be useful
+ *     This file is distributed in the hope that it will be useful,
 *     but WITHOUT ANY WARRANTY; without even the implied warranty of
 *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *     GNU General Public License for more details.
 *
- * Or, alternatively
+ * Or, alternatively,
 *
 *  b) Permission is hereby granted, free of charge, to any person
 *     obtaining a copy of this software and associated documentation
 *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use
+ *     restriction, including without limitation the rights to use,
 *     copy, modify, merge, publish, distribute, sublicense, and/or
 *     sell copies of the Software, and to permit persons to whom the
 *     Software is furnished to do so, subject to the following
@@ -33,11 +33,11 @@
 *     The above copyright notice and this permission notice shall be
 *     included in all copies or substantial portions of the Software.
 *
- *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
 *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
 *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
 *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
 *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
 *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
 *     OTHER DEALINGS IN THE SOFTWARE.
@@ -80,3 +80,69 @@ &uart0 {
 &usb3 {
 	status = "okay";
 };
+
+&mdio {
+	switch0: switch0@1 {
+		compatible = "marvell,mv88e6085";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <1>;
+
+		dsa,member = <0 0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "cpu";
+				ethernet = <&eth0>;
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "wan";
+				phy-handle = <&switch0phy0>;
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan0";
+				phy-handle = <&switch0phy1>;
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan1";
+				phy-handle = <&switch0phy2>;
+			};
+
+		};
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch0phy0: switch0phy0@11 {
+				reg = <0x11>;
+			};
+			switch0phy1: switch0phy1@12 {
+				reg = <0x12>;
+			};
+			switch0phy2: switch0phy2@13 {
+				reg = <0x13>;
+			};
+		};
+	};
+};
+
+&eth0 {
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
--- a/arch/arm64/boot/dts/marvell/armada-372x.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-372x.dtsi
@@ -16,17 +16,17 @@
 *     published by the Free Software Foundation; either version 2 of the
 *     License, or (at your option) any later version.
 *
- *     This file is distributed in the hope that it will be useful
+ *     This file is distributed in the hope that it will be useful,
 *     but WITHOUT ANY WARRANTY; without even the implied warranty of
 *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *     GNU General Public License for more details.
 *
- * Or, alternatively
+ * Or, alternatively,
 *
 *  b) Permission is hereby granted, free of charge, to any person
 *     obtaining a copy of this software and associated documentation
 *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use
+ *     restriction, including without limitation the rights to use,
 *     copy, modify, merge, publish, distribute, sublicense, and/or
 *     sell copies of the Software, and to permit persons to whom the
 *     Software is furnished to do so, subject to the following
@@ -35,11 +35,11 @@
 *     The above copyright notice and this permission notice shall be
 *     included in all copies or substantial portions of the Software.
 *
- *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
 *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
 *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
 *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
 *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
 *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
 *     OTHER DEALINGS IN THE SOFTWARE.

--- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
@@ -15,17 +15,17 @@
 *     published by the Free Software Foundation; either version 2 of the
 *     License, or (at your option) any later version.
 *
- *     This file is distributed in the hope that it will be useful
+ *     This file is distributed in the hope that it will be useful,
 *     but WITHOUT ANY WARRANTY; without even the implied warranty of
 *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *     GNU General Public License for more details.
 *
- * Or, alternatively
+ * Or, alternatively,
 *
 *  b) Permission is hereby granted, free of charge, to any person
 *     obtaining a copy of this software and associated documentation
 *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use
+ *     restriction, including without limitation the rights to use,
 *     copy, modify, merge, publish, distribute, sublicense, and/or
 *     sell copies of the Software, and to permit persons to whom the
 *     Software is furnished to do so, subject to the following
@@ -34,11 +34,11 @@
 *     The above copyright notice and this permission notice shall be
 *     included in all copies or substantial portions of the Software.
 *
- *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
 *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
 *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
 *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
 *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
 *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
 *     OTHER DEALINGS IN THE SOFTWARE.
@@ -98,6 +98,35 @@ internal-regs@d0000000 {
 			/* 32M internal register @ 0xd000_0000 */
 			ranges = <0x0 0x0 0xd0000000 0x2000000>;

+			spi0: spi@10600 {
+				compatible = "marvell,armada-3700-spi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x10600 0xA00>;
+				clocks = <&nb_periph_clk 7>;
+				interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+				num-cs = <4>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@11000 {
+				compatible = "marvell,armada-3700-i2c";
+				reg = <0x11000 0x24>;
+				clocks = <&nb_periph_clk 10>;
+				interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+				mrvl,i2c-fast-mode;
+				status = "disabled";
+			};
+
+			i2c1: i2c@11080 {
+				compatible = "marvell,armada-3700-i2c";
+				reg = <0x11080 0x24>;
+				clocks = <&nb_periph_clk 9>;
+				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+				mrvl,i2c-fast-mode;
+				status = "disabled";
+			};
+
 			uart0: serial@12000 {
 				compatible = "marvell,armada-3700-uart";
 				reg = <0x12000 0x400>;

--- a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts
+++ b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts
+/*
+ * Copyright (C) 2016 Marvell Technology Group Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/*
+ * Device Tree file for MACCHIATOBin Armada 8040 community board platform
+ */
+
+#include "armada-8040.dtsi"
+
+/ {
+	model = "Marvell 8040 MACHIATOBin";
+	compatible = "marvell,armada8040-mcbin", "marvell,armada8040",
+			"marvell,armada-ap806-quad", "marvell,armada-ap806";
+
+	memory@00000000 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	/* Regulator labels correspond with schematics */
+	v_3_3: regulator-3-3v {
+		compatible = "regulator-fixed";
+		regulator-name = "v_3_3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		status = "okay";
+	};
+
+	v_vddo_h: regulator-1-8v {
+		compatible = "regulator-fixed";
+		regulator-name = "v_vddo_h";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		status = "okay";
+	};
+
+	v_5v0_usb3_hst_vbus: regulator-usb3-vbus0 {
+		compatible = "regulator-fixed";
+		regulator-name = "v_5v0_usb3_hst_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		/* actually GPIO controlled, but 8k has no GPIO support yet */
+		regulator-always-on;
+		status = "okay";
+	};
+
+	usb3h0_phy: usb3_phy0 {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&v_5v0_usb3_hst_vbus>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&cpm_i2c0 {
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&cpm_sata0 {
+	/* CPM Lane 0 - U29 */
+	status = "okay";
+};
+
+&cpm_usb3_0 {
+	/* J38? - USB2.0 only */
+	status = "okay";
+};
+
+&cpm_usb3_1 {
+	/* J38? - USB2.0 only */
+	status = "okay";
+};
+
+&cps_sata0 {
+	/* CPS Lane 1 - U32 */
+	/* CPS Lane 3 - U31 */
+	status = "okay";
+};
+
+&cps_spi1 {
+	status = "okay";
+
+	spi-flash@0 {
+		compatible = "st,w25q32";
+		spi-max-frequency = <50000000>;
+		reg = <0>;
+	};
+};
+
+&cps_usb3_0 {
+	/* CPS Lane 2 - CON7 */
+	usb-phy = <&usb3h0_phy>;
+	status = "okay";
+};
--- a/arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi
@@ -74,13 +74,14 @@ cpm_syscon0: system-controller@440000 {
 					"cpm-gop-dp", "none", "cpm-pcie_x10",
 					"cpm-pcie_x11", "cpm-pcie_x4", "cpm-pcie-xor",
 					"cpm-sata", "cpm-sata-usb", "cpm-main",
-					"cpm-sd-mmc", "none", "none",
+					"cpm-sd-mmc-gop", "none", "none",
 					"cpm-slow-io", "cpm-usb3h0", "cpm-usb3h1",
 					"cpm-usb3dev", "cpm-eip150", "cpm-eip197";
 			};

 			cpm_sata0: sata@540000 {
-				compatible = "marvell,armada-8k-ahci";
+				compatible = "marvell,armada-8k-ahci",
+					     "generic-ahci";
 				reg = <0x540000 0x30000>;
 				interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&cpm_syscon0 1 15>;

--- a/arch/arm64/boot/dts/marvell/armada-cp110-slave.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-cp110-slave.dtsi
@@ -74,13 +74,14 @@ cps_syscon0: system-controller@440000 {
 					"cps-gop-dp", "none", "cps-pcie_x10",
 					"cps-pcie_x11", "cps-pcie_x4", "cps-pcie-xor",
 					"cps-sata", "cps-sata-usb", "cps-main",
-					"cps-sd-mmc", "none", "none",
+					"cps-sd-mmc-gop", "none", "none",
 					"cps-slow-io", "cps-usb3h0", "cps-usb3h1",
 					"cps-usb3dev", "cps-eip150", "cps-eip197";
 			};

 			cps_sata0: sata@540000 {
-				compatible = "marvell,armada-8k-ahci";
+				compatible = "marvell,armada-8k-ahci",
+					     "generic-ahci";
 				reg = <0x540000 0x30000>;
 				interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&cps_syscon0 1 15>;

--- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
@@ -182,12 +182,12 @@ cooling-maps {
 				map@0 {
 					trip = <&target>;
 					cooling-device = <&cpu0 0 0>;
-					contribution = <1024>;
+					contribution = <3072>;
 				};
 				map@1 {
 					trip = <&target>;
 					cooling-device = <&cpu2 0 0>;
-					contribution = <2048>;
+					contribution = <1024>;
 				};
 			};
 		};
@@ -401,6 +401,11 @@ iommu: iommu@10205000 {
 		efuse: efuse@10206000 {
 			compatible = "mediatek,mt8173-efuse";
 			reg = <0 0x10206000 0 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			thermal_calibration: calib@528 {
+				reg = <0x528 0xc>;
+			};
 		};

 		apmixedsys: clock-controller@10209000 {
@@ -574,6 +579,8 @@ thermal: thermal@1100b000 {
 			resets = <&pericfg MT8173_PERI_THERM_SW_RST>;
 			mediatek,auxadc = <&auxadc>;
 			mediatek,apmixedsys = <&apmixedsys>;
+			nvmem-cells = <&thermal_calibration>;
+			nvmem-cell-names = "calibration-data";
 		};

 		nor_flash: spi@1100d000 {
@@ -780,6 +787,8 @@ mmsys: clock-controller@14000000 {
 			compatible = "mediatek,mt8173-mmsys", "syscon";
 			reg = <0 0x14000000 0 0x1000>;
 			power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+			assigned-clocks = <&topckgen CLK_TOP_MM_SEL>;
+			assigned-clock-rates = <400000000>;
 			#clock-cells = <1>;
 		};


--- a/arch/arm64/boot/dts/nvidia/tegra186.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra186.dtsi
+#include <dt-bindings/clock/tegra186-clock.h>
 #include <dt-bindings/gpio/tegra186-gpio.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/mailbox/tegra186-hsp.h>
+#include <dt-bindings/reset/tegra186-reset.h>

 / {
 	compatible = "nvidia,tegra186";
@@ -29,9 +32,9 @@ uarta: serial@3100000 {
 		reg = <0x0 0x03100000 0x0 0x40>;
 		reg-shift = <2>;
 		interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&bpmp 55>;
+		clocks = <&bpmp TEGRA186_CLK_UARTA>;
 		clock-names = "serial";
-		resets = <&bpmp 47>;
+		resets = <&bpmp TEGRA186_RESET_UARTA>;
 		reset-names = "serial";
 		status = "disabled";
 	};
@@ -41,9 +44,9 @@ uartb: serial@3110000 {
 		reg = <0x0 0x03110000 0x0 0x40>;
 		reg-shift = <2>;
 		interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&bpmp 56>;
+		clocks = <&bpmp TEGRA186_CLK_UARTB>;
 		clock-names = "serial";
-		resets = <&bpmp 48>;
+		resets = <&bpmp TEGRA186_RESET_UARTB>;
 		reset-names = "serial";
 		status = "disabled";
 	};
@@ -53,9 +56,9 @@ uartd: serial@3130000 {
 		reg = <0x0 0x03130000 0x0 0x40>;
 		reg-shift = <2>;
 		interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&bpmp 77>;
+		clocks = <&bpmp TEGRA186_CLK_UARTD>;
 		clock-names = "serial";
-		resets = <&bpmp 50>;
+		resets = <&bpmp TEGRA186_RESET_UARTD>;
 		reset-names = "serial";
 		status = "disabled";
 	};
@@ -65,9 +68,9 @@ uarte: serial@3140000 {
 		reg = <0x0 0x03140000 0x0 0x40>;
 		reg-shift = <2>;
 		interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&bpmp 194>;
+		clocks = <&bpmp TEGRA186_CLK_UARTE>;
 		clock-names = "serial";
-		resets = <&bpmp 132>;
+		resets = <&bpmp TEGRA186_RESET_UARTE>;
 		reset-names = "serial";
 		status = "disabled";
 	};
@@ -77,9 +80,9 @@ uartf: serial@3150000 {
 		reg = <0x0 0x03150000 0x0 0x40>;
 		reg-shift = <2>;
 		interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&bpmp 195>;
+		clocks = <&bpmp TEGRA186_CLK_UARTF>;
 		clock-names = "serial";
-		resets = <&bpmp 111>;
+		resets = <&bpmp TEGRA186_RESET_UARTF>;
 		reset-names = "serial";
 		status = "disabled";
 	};
@@ -90,9 +93,9 @@ gen1_i2c: i2c@3160000 {
 		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&bpmp 47>;
+		clocks = <&bpmp TEGRA186_CLK_I2C1>;
 		clock-names = "div-clk";
-		resets = <&bpmp 19>;
+		resets = <&bpmp TEGRA186_RESET_I2C1>;
 		reset-names = "i2c";
 		status = "disabled";
 	};
@@ -103,9 +106,9 @@ cam_i2c: i2c@3180000 {
 		interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&bpmp 75>;
+		clocks = <&bpmp TEGRA186_CLK_I2C3>;
 		clock-names = "div-clk";
-		resets = <&bpmp 21>;
+		resets = <&bpmp TEGRA186_RESET_I2C3>;
 		reset-names = "i2c";
 		status = "disabled";
 	};
@@ -117,9 +120,9 @@ dp_aux_ch1_i2c: i2c@3190000 {
 		interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&bpmp 86>;
+		clocks = <&bpmp TEGRA186_CLK_I2C4>;
 		clock-names = "div-clk";
-		resets = <&bpmp 22>;
+		resets = <&bpmp TEGRA186_RESET_I2C4>;
 		reset-names = "i2c";
 		status = "disabled";
 	};
@@ -131,9 +134,9 @@ pwr_i2c: i2c@31a0000 {
 		interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&bpmp 48>;
+		clocks = <&bpmp TEGRA186_CLK_I2C5>;
 		clock-names = "div-clk";
-		resets = <&bpmp 23>;
+		resets = <&bpmp TEGRA186_RESET_I2C5>;
 		reset-names = "i2c";
 		status = "disabled";
 	};
@@ -145,9 +148,9 @@ dp_aux_ch0_i2c: i2c@31b0000 {
 		interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&bpmp 125>;
+		clocks = <&bpmp TEGRA186_CLK_I2C6>;
 		clock-names = "div-clk";
-		resets = <&bpmp 24>;
+		resets = <&bpmp TEGRA186_RESET_I2C6>;
 		reset-names = "i2c";
 		status = "disabled";
 	};
@@ -158,9 +161,9 @@ gen7_i2c: i2c@31c0000 {
 		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&bpmp 182>;
+		clocks = <&bpmp TEGRA186_CLK_I2C7>;
 		clock-names = "div-clk";
-		resets = <&bpmp 81>;
+		resets = <&bpmp TEGRA186_RESET_I2C7>;
 		reset-names = "i2c";
 		status = "disabled";
 	};
@@ -171,9 +174,9 @@ gen9_i2c: i2c@31e0000 {
 		interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&bpmp 183>;
+		clocks = <&bpmp TEGRA186_CLK_I2C9>;
 		clock-names = "div-clk";
-		resets = <&bpmp 83>;
+		resets = <&bpmp TEGRA186_RESET_I2C9>;
 		reset-names = "i2c";
 		status = "disabled";
 	};
@@ -182,9 +185,9 @@ sdmmc1: sdhci@3400000 {
 		compatible = "nvidia,tegra186-sdhci";
 		reg = <0x0 0x03400000 0x0 0x10000>;
 		interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&bpmp 52>;
+		clocks = <&bpmp TEGRA186_CLK_SDMMC1>;
 		clock-names = "sdhci";
-		resets = <&bpmp 33>;
+		resets = <&bpmp TEGRA186_RESET_SDMMC1>;
 		reset-names = "sdhci";
 		status = "disabled";
 	};
@@ -193,9 +196,9 @@ sdmmc2: sdhci@3420000 {
 		compatible = "nvidia,tegra186-sdhci";
 		reg = <0x0 0x03420000 0x0 0x10000>;
 		interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&bpmp 53>;
+		clocks = <&bpmp TEGRA186_CLK_SDMMC2>;
 		clock-names = "sdhci";
-		resets = <&bpmp 34>;
+		resets = <&bpmp TEGRA186_RESET_SDMMC2>;
 		reset-names = "sdhci";
 		status = "disabled";
 	};
@@ -204,9 +207,9 @@ sdmmc3: sdhci@3440000 {
 		compatible = "nvidia,tegra186-sdhci";
 		reg = <0x0 0x03440000 0x0 0x10000>;
 		interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&bpmp 76>;
+		clocks = <&bpmp TEGRA186_CLK_SDMMC3>;
 		clock-names = "sdhci";
-		resets = <&bpmp 35>;
+		resets = <&bpmp TEGRA186_RESET_SDMMC3>;
 		reset-names = "sdhci";
 		status = "disabled";
 	};
@@ -215,9 +218,9 @@ sdmmc4: sdhci@3460000 {
 		compatible = "nvidia,tegra186-sdhci";
 		reg = <0x0 0x03460000 0x0 0x10000>;
 		interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&bpmp 54>;
+		clocks = <&bpmp TEGRA186_CLK_SDMMC4>;
 		clock-names = "sdhci";
-		resets = <&bpmp 36>;
+		resets = <&bpmp TEGRA186_RESET_SDMMC4>;
 		reset-names = "sdhci";
 		status = "disabled";
 	};
@@ -248,9 +251,9 @@ gen2_i2c: i2c@c240000 {
 		interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&bpmp 218>;
+		clocks = <&bpmp TEGRA186_CLK_I2C2>;
 		clock-names = "div-clk";
-		resets = <&bpmp 20>;
+		resets = <&bpmp TEGRA186_RESET_I2C2>;
 		reset-names = "i2c";
 		status = "disabled";
 	};
@@ -261,9 +264,9 @@ gen8_i2c: i2c@c250000 {
 		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&bpmp 219>;
+		clocks = <&bpmp TEGRA186_CLK_I2C8>;
 		clock-names = "div-clk";
-		resets = <&bpmp 82>;
+		resets = <&bpmp TEGRA186_RESET_I2C8>;
 		reset-names = "i2c";
 		status = "disabled";
 	};
@@ -273,9 +276,9 @@ uartc: serial@c280000 {
 		reg = <0x0 0x0c280000 0x0 0x40>;
 		reg-shift = <2>;
 		interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&bpmp 215>;
+		clocks = <&bpmp TEGRA186_CLK_UARTC>;
 		clock-names = "serial";
-		resets = <&bpmp 49>;
+		resets = <&bpmp TEGRA186_RESET_UARTC>;
 		reset-names = "serial";
 		status = "disabled";
 	};
@@ -285,9 +288,9 @@ uartg: serial@c290000 {
 		reg = <0x0 0x0c290000 0x0 0x40>;
 		reg-shift = <2>;
 		interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&bpmp 216>;
+		clocks = <&bpmp TEGRA186_CLK_UARTG>;
 		clock-names = "serial";
-		resets = <&bpmp 112>;
+		resets = <&bpmp TEGRA186_RESET_UARTG>;
 		reset-names = "serial";
 		status = "disabled";
 	};
@@ -369,7 +372,8 @@ cpu@5 {

 	bpmp: bpmp {
 		compatible = "nvidia,tegra186-bpmp";
-		mboxes = <&hsp_top0 0 19>;
+		mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_DB
+				    TEGRA_HSP_DB_MASTER_BPMP>;
 		shmem = <&cpu_bpmp_tx &cpu_bpmp_rx>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;

--- a/arch/arm64/boot/dts/qcom/apq8016-sbc-pmic-pins.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc-pmic-pins.dtsi
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>

 &pm8916_gpios {

@@ -30,6 +31,18 @@ pinconf {

 &pm8916_mpps {

+	pinctrl-names = "default";
+	pinctrl-0 = <&ls_exp_gpio_f>;
+
+	ls_exp_gpio_f: pm8916_mpp4 {
+		pinconf {
+			pins = "mpp4";
+			function = "digital";
+			output-low;
+			power-source = <PM8916_MPP_L5>;	// 1.8V
+		};
+	};
+
 	pm8916_mpps_leds: pm8916_mpps_leds {
 		pinconf {
 			pins = "mpp2", "mpp3";

--- a/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi
@@ -72,4 +72,17 @@ pinconf {
 			bias-disable;
 		};
 	};
+
+	msm_key_volp_n_default: msm_key_volp_n_default {
+		pinmux {
+			function = "gpio";
+			pins = "gpio107";
+		};
+		pinconf {
+			pins = "gpio107";
+			drive-strength = <8>;
+			input-enable;
+			bias-pull-up;
+		};
+	};
 };
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
@@ -15,6 +15,8 @@
 #include "pm8916.dtsi"
 #include "apq8016-sbc-soc-pins.dtsi"
 #include "apq8016-sbc-pmic-pins.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 #include <dt-bindings/sound/apq8016-lpass.h>

 / {
@@ -85,6 +87,7 @@ adv_bridge: bridge@39 {
 				pinctrl-names = "default","sleep";
 				pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
 				pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
+				#sound-dai-cells = <1>;

 				ports {
 					#address-cells = <1>;
@@ -285,6 +288,15 @@ sound: sound {
                        qcom,audio-routing =
                                "AMIC2", "MIC BIAS Internal2",
                                "AMIC3", "MIC BIAS External1";
+			external-dai-link@0 {
+				link-name = "ADV7533";
+				cpu { /* QUAT */
+					sound-dai = <&lpass MI2S_QUATERNARY>;
+				};
+				codec {
+					sound-dai = <&adv_bridge 0>;
+				};
+			};

                        internal-codec-playback-dai-link@0 {            /* I2S - Internal codec */
                                link-name = "WCD";
@@ -306,6 +318,10 @@ codec {
                                };
                        };
                };
+
+		wcnss@a21b000 {
+			status = "okay";
+		};
 	};

 	usb2513 {
@@ -331,6 +347,22 @@ hdmi_con: endpoint {
 			};
 		};
 	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&msm_key_volp_n_default>;
+
+		button@0 {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
+		};
+	};
 };

 &wcd_codec {

--- a/arch/arm64/boot/dts/qcom/apq8096-db820c-pmic-pins.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c-pmic-pins.dtsi
@@ -5,11 +5,23 @@ &pm8994_gpios {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ls_exp_gpio_f>;

-	ls_exp_gpio_f: pm8916_mpp4 {
+	ls_exp_gpio_f: pm8994_gpio5 {
 		pinconf {
 			pins = "gpio5";
 			output-low;
 			power-source = <2>; // PM8994_GPIO_S4, 1.8V
 		};
 	};
+
+	volume_up_gpio: pm8996_gpio2 {
+		pinconf {
+			pins = "gpio2";
+			function = "normal";
+			input-enable;
+			drive-push-pull;
+			bias-pull-up;
+			qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+			power-source = <PM8994_GPIO_S4>; // 1.8V
+		};
+	};
 };
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
@@ -15,6 +15,8 @@
 #include "pm8994.dtsi"
 #include "apq8096-db820c-pins.dtsi"
 #include "apq8096-db820c-pmic-pins.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>

 / {
 	aliases {
@@ -87,4 +89,21 @@ sdhci@74a4900 {
 			status = "okay";
 		};
 	};
+
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&volume_up_gpio>;
+
+		button@0 {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm8994_gpios 2 GPIO_ACTIVE_LOW>;
+		};
+	};
 };
--- a/arch/arm64/boot/dts/qcom/msm8916-pins.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916-pins.dtsi
@@ -720,4 +720,17 @@ pinconf {
 			};
 		};
 	};
+
+	wcnss_pin_a: wcnss-active {
+		pinmux {
+			pins = "gpio40", "gpio41", "gpio42", "gpio43", "gpio44";
+			function = "wcss_wlan";
+		};
+
+		pinconf {
+			pins = "gpio40", "gpio41", "gpio42", "gpio43", "gpio44";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
 };
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -14,6 +14,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-msm8916.h>
 #include <dt-bindings/reset/qcom,gcc-msm8916.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>

 / {
 	model = "Qualcomm Technologies, Inc. MSM8916";
@@ -82,7 +83,7 @@ mpss_mem: mpss@86800000 {
 			no-map;
 		};

-		wcnss@89300000 {
+		wcnss_mem: wcnss@89300000 {
 			reg = <0x0 0x89300000 0x0 0x600000>;
 			no-map;
 		};
@@ -856,6 +857,316 @@ mpss {
 				memory-region = <&mpss_mem>;
 			};
 		};
+
+		pronto: wcnss@a21b000 {
+			compatible = "qcom,pronto-v2-pil", "qcom,pronto";
+			reg = <0x0a204000 0x2000>, <0x0a202000 0x1000>, <0x0a21b000 0x3000>;
+			reg-names = "ccu", "dxe", "pmu";
+
+			memory-region = <&wcnss_mem>;
+
+			interrupts-extended = <&intc 0 149 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+			vddmx-supply = <&pm8916_l3>;
+			vddpx-supply = <&pm8916_l7>;
+
+			qcom,state = <&wcnss_smp2p_out 0>;
+			qcom,state-names = "stop";
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&wcnss_pin_a>;
+
+			status = "disabled";
+
+			iris {
+				compatible = "qcom,wcn3620";
+
+				clocks = <&rpmcc RPM_SMD_RF_CLK2>;
+				clock-names = "xo";
+
+				vddxo-supply = <&pm8916_l7>;
+				vddrfa-supply = <&pm8916_s3>;
+				vddpa-supply = <&pm8916_l9>;
+				vdddig-supply = <&pm8916_l5>;
+			};
+
+			smd-edge {
+				interrupts = <0 142 1>;
+
+				qcom,ipc = <&apcs 8 17>;
+				qcom,smd-edge = <6>;
+				qcom,remote-pid = <4>;
+
+				label = "pronto";
+
+				wcnss {
+					compatible = "qcom,wcnss";
+					qcom,smd-channels = "WCNSS_CTRL";
+
+					qcom,mmio = <&pronto>;
+
+					bt {
+						compatible = "qcom,wcnss-bt";
+					};
+
+					wifi {
+						compatible = "qcom,wcnss-wlan";
+
+						interrupts = <0 145 IRQ_TYPE_LEVEL_HIGH>,
+							     <0 146 IRQ_TYPE_LEVEL_HIGH>;
+						interrupt-names = "tx", "rx";
+
+						qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>;
+						qcom,smem-state-names = "tx-enable", "tx-rings-empty";
+					};
+				};
+			};
+		};
+
+		tpiu@820000 {
+			compatible = "arm,coresight-tpiu", "arm,primecell";
+			reg = <0x820000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			port {
+				tpiu_in: endpoint {
+					slave-mode;
+					remote-endpoint = <&replicator_out1>;
+				};
+			};
+		};
+
+		funnel@821000 {
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0x821000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				/*
+				 * Not described input ports:
+				 * 0 - connected to Resource and Power Manger CPU ETM
+				 * 1 - not-connected
+				 * 2 - connected to Modem CPU ETM
+				 * 3 - not-connected
+				 * 5 - not-connected
+				 * 6 - connected trought funnel to Wireless CPU ETM
+				 * 7 - connected to STM component
+				 */
+
+				port@4 {
+					reg = <4>;
+					funnel0_in4: endpoint {
+						slave-mode;
+						remote-endpoint = <&funnel1_out>;
+					};
+				};
+				port@8 {
+					reg = <0>;
+					funnel0_out: endpoint {
+						remote-endpoint = <&etf_in>;
+					};
+				};
+			};
+		};
+
+		replicator@824000 {
+			compatible = "qcom,coresight-replicator1x", "arm,primecell";
+			reg = <0x824000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					replicator_out0: endpoint {
+						remote-endpoint = <&etr_in>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					replicator_out1: endpoint {
+						remote-endpoint = <&tpiu_in>;
+					};
+				};
+				port@2 {
+					reg = <0>;
+					replicator_in: endpoint {
+						slave-mode;
+						remote-endpoint = <&etf_out>;
+					};
+				};
+			};
+		};
+
+		etf@825000 {
+			compatible = "arm,coresight-tmc", "arm,primecell";
+			reg = <0x825000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					etf_out: endpoint {
+						slave-mode;
+						remote-endpoint = <&funnel0_out>;
+					};
+				};
+				port@1 {
+					reg = <0>;
+					etf_in: endpoint {
+						remote-endpoint = <&replicator_in>;
+					};
+				};
+			};
+		};
+
+		etr@826000 {
+			compatible = "arm,coresight-tmc", "arm,primecell";
+			reg = <0x826000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			port {
+				etr_in: endpoint {
+					slave-mode;
+					remote-endpoint = <&replicator_out0>;
+				};
+			};
+		};
+
+		funnel@841000 {	/* APSS funnel only 4 inputs are used */
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0x841000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					funnel1_in0: endpoint {
+						slave-mode;
+						remote-endpoint = <&etm0_out>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					funnel1_in1: endpoint {
+						slave-mode;
+						remote-endpoint = <&etm1_out>;
+					};
+				};
+				port@2 {
+					reg = <2>;
+					funnel1_in2: endpoint {
+						slave-mode;
+						remote-endpoint = <&etm2_out>;
+					};
+				};
+				port@3 {
+					reg = <3>;
+					funnel1_in3: endpoint {
+						slave-mode;
+						remote-endpoint = <&etm3_out>;
+					};
+				};
+				port@4 {
+					reg = <0>;
+					funnel1_out: endpoint {
+						remote-endpoint = <&funnel0_in4>;
+					};
+				};
+			};
+		};
+
+		etm@85c000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0x85c000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU0>;
+
+			port {
+				etm0_out: endpoint {
+				remote-endpoint = <&funnel1_in0>;
+				};
+			};
+		};
+
+		etm@85d000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0x85d000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU1>;
+
+			port {
+				etm1_out: endpoint {
+					remote-endpoint = <&funnel1_in1>;
+				};
+			};
+		};
+
+		etm@85e000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0x85e000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU2>;
+
+			port {
+				etm2_out: endpoint {
+					remote-endpoint = <&funnel1_in2>;
+				};
+			};
+		};
+
+		etm@85f000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0x85f000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU3>;
+
+			port {
+				etm3_out: endpoint {
+					remote-endpoint = <&funnel1_in3>;
+				};
+			};
+		};
 	};

 	smd {
@@ -871,7 +1182,7 @@ rpm_requests {
 				qcom,smd-channels = "rpm_requests";

 				rpmcc: qcom,rpmcc {
-					compatible = "qcom,rpmcc-msm8916", "qcom,rpmcc";
+					compatible = "qcom,rpmcc-msm8916";
 					#clock-cells = <1>;
 				};


--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -258,6 +258,12 @@ psci {
 		method = "smc";
 	};

+	firmware {
+		scm {
+			compatible = "qcom,scm-msm8996";
+		};
+	};
+
 	tcsr_mutex: hwlock {
 		compatible = "qcom,tcsr-mutex";
 		syscon = <&tcsr_mutex_regs 0 0x1000>;

--- a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
@@ -277,6 +277,8 @@ &rcar_sound {
 		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
 		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
 		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
 		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
 		 <&audio_clk_a>, <&cs2000>,
 		 <&audio_clk_c>,

--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -412,6 +412,8 @@ &rcar_sound {
 		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
 		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
 		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
 		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
 		 <&audio_clk_a>, <&cs2000>,
 		 <&audio_clk_c>,

--- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
@@ -166,6 +166,9 @@ gic: interrupt-controller@f1010000 {
 			      <0x0 0xf1060000 0 0x20000>;
 			interrupts = <GIC_PPI 9
 					(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			clocks = <&cpg CPG_MOD 408>;
+			clock-names = "clk";
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
 		};

 		wdt0: watchdog@e6020000 {
@@ -337,72 +340,6 @@ sysc: system-controller@e6180000 {
 			#power-domain-cells = <1>;
 		};

-		audma0: dma-controller@ec700000 {
-			compatible = "renesas,dmac-r8a7795",
-				     "renesas,rcar-dmac";
-			reg = <0 0xec700000 0 0x10000>;
-			interrupts = <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "error",
-					"ch0", "ch1", "ch2", "ch3",
-					"ch4", "ch5", "ch6", "ch7",
-					"ch8", "ch9", "ch10", "ch11",
-					"ch12", "ch13", "ch14", "ch15";
-			clocks = <&cpg CPG_MOD 502>;
-			clock-names = "fck";
-			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
-			#dma-cells = <1>;
-			dma-channels = <16>;
-		};
-
-		audma1: dma-controller@ec720000 {
-			compatible = "renesas,dmac-r8a7795",
-				     "renesas,rcar-dmac";
-			reg = <0 0xec720000 0 0x10000>;
-			interrupts = <GIC_SPI 351 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 349 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 382 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 383 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "error",
-					"ch0", "ch1", "ch2", "ch3",
-					"ch4", "ch5", "ch6", "ch7",
-					"ch8", "ch9", "ch10", "ch11",
-					"ch12", "ch13", "ch14", "ch15";
-			clocks = <&cpg CPG_MOD 501>;
-			clock-names = "fck";
-			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
-			#dma-cells = <1>;
-			dma-channels = <16>;
-		};
-
 		pfc: pfc@e6060000 {
 			compatible = "renesas,pfc-r8a7795";
 			reg = <0 0xe6060000 0 0x50c>;
@@ -522,6 +459,72 @@ GIC_SPI 431 IRQ_TYPE_LEVEL_HIGH
 			dma-channels = <16>;
 		};

+		audma0: dma-controller@ec700000 {
+			compatible = "renesas,dmac-r8a7795",
+				     "renesas,rcar-dmac";
+			reg = <0 0xec700000 0 0x10000>;
+			interrupts = <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					"ch0", "ch1", "ch2", "ch3",
+					"ch4", "ch5", "ch6", "ch7",
+					"ch8", "ch9", "ch10", "ch11",
+					"ch12", "ch13", "ch14", "ch15";
+			clocks = <&cpg CPG_MOD 502>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#dma-cells = <1>;
+			dma-channels = <16>;
+		};
+
+		audma1: dma-controller@ec720000 {
+			compatible = "renesas,dmac-r8a7795",
+				     "renesas,rcar-dmac";
+			reg = <0 0xec720000 0 0x10000>;
+			interrupts = <GIC_SPI 351 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 349 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 382 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 383 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					"ch0", "ch1", "ch2", "ch3",
+					"ch4", "ch5", "ch6", "ch7",
+					"ch8", "ch9", "ch10", "ch11",
+					"ch12", "ch13", "ch14", "ch15";
+			clocks = <&cpg CPG_MOD 501>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#dma-cells = <1>;
+			dma-channels = <16>;
+		};
+
 		avb: ethernet@e6800000 {
 			compatible = "renesas,etheravb-r8a7795",
 				     "renesas,etheravb-rcar-gen3";
@@ -563,6 +566,7 @@ avb: ethernet@e6800000 {
 			phy-mode = "rgmii-id";
 			#address-cells = <1>;
 			#size-cells = <0>;
+			status = "disabled";
 		};

 		can0: can@e6c30000 {
@@ -792,7 +796,8 @@ scif5: serial@e6f30000 {
 		i2c0: i2c@e6500000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7795";
+			compatible = "renesas,i2c-r8a7795",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe6500000 0 0x40>;
 			interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 931>;
@@ -806,7 +811,8 @@ i2c0: i2c@e6500000 {
 		i2c1: i2c@e6508000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7795";
+			compatible = "renesas,i2c-r8a7795",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe6508000 0 0x40>;
 			interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 930>;
@@ -820,7 +826,8 @@ i2c1: i2c@e6508000 {
 		i2c2: i2c@e6510000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7795";
+			compatible = "renesas,i2c-r8a7795",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe6510000 0 0x40>;
 			interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 929>;
@@ -834,7 +841,8 @@ i2c2: i2c@e6510000 {
 		i2c3: i2c@e66d0000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7795";
+			compatible = "renesas,i2c-r8a7795",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe66d0000 0 0x40>;
 			interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 928>;
@@ -848,7 +856,8 @@ i2c3: i2c@e66d0000 {
 		i2c4: i2c@e66d8000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7795";
+			compatible = "renesas,i2c-r8a7795",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe66d8000 0 0x40>;
 			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 927>;
@@ -862,7 +871,8 @@ i2c4: i2c@e66d8000 {
 		i2c5: i2c@e66e0000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7795";
+			compatible = "renesas,i2c-r8a7795",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe66e0000 0 0x40>;
 			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 919>;
@@ -876,7 +886,8 @@ i2c5: i2c@e66e0000 {
 		i2c6: i2c@e66e8000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7795";
+			compatible = "renesas,i2c-r8a7795",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe66e8000 0 0x40>;
 			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 918>;
@@ -887,6 +898,69 @@ i2c6: i2c@e66e8000 {
 			status = "disabled";
 		};

+		pwm0: pwm@e6e30000 {
+			compatible = "renesas,pwm-r8a7795", "renesas,pwm-rcar";
+			reg = <0 0xe6e30000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm1: pwm@e6e31000 {
+			compatible = "renesas,pwm-r8a7795", "renesas,pwm-rcar";
+			reg = <0 0xe6e31000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm2: pwm@e6e32000 {
+			compatible = "renesas,pwm-r8a7795", "renesas,pwm-rcar";
+			reg = <0 0xe6e32000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm3: pwm@e6e33000 {
+			compatible = "renesas,pwm-r8a7795", "renesas,pwm-rcar";
+			reg = <0 0xe6e33000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm4: pwm@e6e34000 {
+			compatible = "renesas,pwm-r8a7795", "renesas,pwm-rcar";
+			reg = <0 0xe6e34000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm5: pwm@e6e35000 {
+			compatible = "renesas,pwm-r8a7795", "renesas,pwm-rcar";
+			reg = <0 0xe6e35000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm6: pwm@e6e36000 {
+			compatible = "renesas,pwm-r8a7795", "renesas,pwm-rcar";
+			reg = <0 0xe6e36000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
 		rcar_sound: sound@ec500000 {
 			/*
 			 * #sound-dai-cells is required
@@ -919,6 +993,8 @@ rcar_sound: sound@ec500000 {
 				 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
 				 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
 				 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
+				 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+				 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
 				 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
 				 <&audio_clk_a>, <&audio_clk_b>,
 				 <&audio_clk_c>,
@@ -930,6 +1006,8 @@ rcar_sound: sound@ec500000 {
 				      "src.9", "src.8", "src.7", "src.6",
 				      "src.5", "src.4", "src.3", "src.2",
 				      "src.1", "src.0",
+				      "mix.1", "mix.0",
+				      "ctu.1", "ctu.0",
 				      "dvc.0", "dvc.1",
 				      "clk_a", "clk_b", "clk_c", "clk_i";
 			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
@@ -946,6 +1024,22 @@ dvc1: dvc-1 {
 				};
 			};

+			rcar_sound,mix {
+				mix0: mix-0 { };
+				mix1: mix-1 { };
+			};
+
+			rcar_sound,ctu {
+				ctu00: ctu-0 { };
+				ctu01: ctu-1 { };
+				ctu02: ctu-2 { };
+				ctu03: ctu-3 { };
+				ctu10: ctu-4 { };
+				ctu11: ctu-5 { };
+				ctu12: ctu-6 { };
+				ctu13: ctu-7 { };
+			};
+
 			rcar_sound,src {
 				src0: src-0 {
 					interrupts = <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
@@ -1058,6 +1152,7 @@ sata: sata@ee300000 {
 			reg = <0 0xee300000 0 0x1fff>;
 			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 815>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
 			status = "disabled";
 		};

@@ -1146,7 +1241,8 @@ sdhi3: sd@ee160000 {
 		};

 		usb2_phy0: usb-phy@ee080200 {
-			compatible = "renesas,usb2-phy-r8a7795";
+			compatible = "renesas,usb2-phy-r8a7795",
+				     "renesas,rcar-gen3-usb2-phy";
 			reg = <0 0xee080200 0 0x700>;
 			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 703>;
@@ -1156,7 +1252,8 @@ usb2_phy0: usb-phy@ee080200 {
 		};

 		usb2_phy1: usb-phy@ee0a0200 {
-			compatible = "renesas,usb2-phy-r8a7795";
+			compatible = "renesas,usb2-phy-r8a7795",
+				     "renesas,rcar-gen3-usb2-phy";
 			reg = <0 0xee0a0200 0 0x700>;
 			clocks = <&cpg CPG_MOD 702>;
 			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
@@ -1165,7 +1262,8 @@ usb2_phy1: usb-phy@ee0a0200 {
 		};

 		usb2_phy2: usb-phy@ee0c0200 {
-			compatible = "renesas,usb2-phy-r8a7795";
+			compatible = "renesas,usb2-phy-r8a7795",
+				     "renesas,rcar-gen3-usb2-phy";
 			reg = <0 0xee0c0200 0 0x700>;
 			clocks = <&cpg CPG_MOD 701>;
 			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
@@ -1256,7 +1354,8 @@ hsusb: usb@e6590000 {
 		};

 		pciec0: pcie@fe000000 {
-			compatible = "renesas,pcie-r8a7795";
+			compatible = "renesas,pcie-r8a7795",
+				     "renesas,pcie-rcar-gen3";
 			reg = <0 0xfe000000 0 0x80000>;
 			#address-cells = <3>;
 			#size-cells = <2>;
@@ -1281,7 +1380,8 @@ pciec0: pcie@fe000000 {
 		};

 		pciec1: pcie@ee800000 {
-			compatible = "renesas,pcie-r8a7795";
+			compatible = "renesas,pcie-r8a7795",
+				     "renesas,pcie-rcar-gen3";
 			reg = <0 0xee800000 0 0x80000>;
 			#address-cells = <3>;
 			#size-cells = <2>;
@@ -1551,5 +1651,63 @@ du_out_lvds0: endpoint {
 				};
 			};
 		};
+
+		tsc: thermal@e6198000 {
+			compatible = "renesas,r8a7795-thermal";
+			reg = <0 0xe6198000 0 0x68>,
+			      <0 0xe61a0000 0 0x5c>,
+			      <0 0xe61a8000 0 0x5c>;
+			interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 522>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#thermal-sensor-cells = <1>;
+			status = "okay";
+		};
+
+		thermal-zones {
+			sensor_thermal1: sensor-thermal1 {
+				polling-delay-passive = <250>;
+				polling-delay = <1000>;
+				thermal-sensors = <&tsc 0>;
+
+				trips {
+					sensor1_crit: sensor1-crit {
+						temperature = <120000>;
+						hysteresis = <2000>;
+						type = "critical";
+					};
+				};
+			};
+
+			sensor_thermal2: sensor-thermal2 {
+				polling-delay-passive = <250>;
+				polling-delay = <1000>;
+				thermal-sensors = <&tsc 1>;
+
+				trips {
+					sensor2_crit: sensor2-crit {
+						temperature = <120000>;
+						hysteresis = <2000>;
+						type = "critical";
+					};
+				};
+			};
+
+			sensor_thermal3: sensor-thermal3 {
+				polling-delay-passive = <250>;
+				polling-delay = <1000>;
+				thermal-sensors = <&tsc 2>;
+
+				trips {
+					sensor3_crit: sensor3-crit {
+						temperature = <120000>;
+						hysteresis = <2000>;
+						type = "critical";
+					};
+				};
+			};
+		};
 	};
 };
--- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
@@ -18,6 +18,7 @@ / {

 	aliases {
 		serial0 = &scif2;
+		ethernet0 = &avb;
 	};

 	chosen {
@@ -31,6 +32,11 @@ memory@48000000 {
 		reg = <0x0 0x48000000 0x0 0x78000000>;
 	};

+	memory@600000000 {
+		device_type = "memory";
+		reg = <0x6 0x00000000 0x0 0x80000000>;
+	};
+
 	reg_1p8v: regulator0 {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-1.8V";
@@ -102,6 +108,11 @@ &pfc {
 	pinctrl-0 = <&scif_clk_pins>;
 	pinctrl-names = "default";

+	avb_pins: avb {
+		groups = "avb_mdc";
+		function = "avb";
+	};
+
 	scif2_pins: scif2 {
 		groups = "scif2_data_a";
 		function = "scif2";
@@ -153,6 +164,32 @@ sdhi3_pins_uhs: sd3_uhs {
 	};
 };

+&avb {
+	pinctrl-0 = <&avb_pins>;
+	pinctrl-names = "default";
+	renesas,no-ether-link;
+	phy-handle = <&phy0>;
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		rxc-skew-ps = <900>;
+		rxdv-skew-ps = <0>;
+		rxd0-skew-ps = <0>;
+		rxd1-skew-ps = <0>;
+		rxd2-skew-ps = <0>;
+		rxd3-skew-ps = <0>;
+		txc-skew-ps = <900>;
+		txen-skew-ps = <0>;
+		txd0-skew-ps = <0>;
+		txd1-skew-ps = <0>;
+		txd2-skew-ps = <0>;
+		txd3-skew-ps = <0>;
+		reg = <0>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
 &extal_clk {
 	clock-frequency = <16666666>;
 };

--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -69,6 +69,13 @@ extalr_clk: extalr {
 		clock-frequency = <0>;
 	};

+	/* External CAN clock - to be overridden by boards that provide it */
+	can_clk: can {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
 	/* External SCIF clock - to be overridden by boards that provide it */
 	scif_clk: scif {
 		compatible = "fixed-clock";
@@ -94,6 +101,9 @@ gic: interrupt-controller@f1010000 {
 			      <0x0 0xf1060000 0 0x20000>;
 			interrupts = <GIC_PPI 9
 					(GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>;
+			clocks = <&cpg CPG_MOD 408>;
+			clock-names = "clk";
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
 		};

 		timer {
@@ -262,7 +272,8 @@ sysc: system-controller@e6180000 {
 		i2c0: i2c@e6500000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7796";
+			compatible = "renesas,i2c-r8a7796",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe6500000 0 0x40>;
 			interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 931>;
@@ -277,7 +288,8 @@ i2c0: i2c@e6500000 {
 		i2c1: i2c@e6508000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7796";
+			compatible = "renesas,i2c-r8a7796",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe6508000 0 0x40>;
 			interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 930>;
@@ -292,7 +304,8 @@ i2c1: i2c@e6508000 {
 		i2c2: i2c@e6510000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7796";
+			compatible = "renesas,i2c-r8a7796",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe6510000 0 0x40>;
 			interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 929>;
@@ -307,7 +320,8 @@ i2c2: i2c@e6510000 {
 		i2c3: i2c@e66d0000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7796";
+			compatible = "renesas,i2c-r8a7796",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe66d0000 0 0x40>;
 			interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 928>;
@@ -321,7 +335,8 @@ i2c3: i2c@e66d0000 {
 		i2c4: i2c@e66d8000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7796";
+			compatible = "renesas,i2c-r8a7796",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe66d8000 0 0x40>;
 			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 927>;
@@ -335,7 +350,8 @@ i2c4: i2c@e66d8000 {
 		i2c5: i2c@e66e0000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7796";
+			compatible = "renesas,i2c-r8a7796",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe66e0000 0 0x40>;
 			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 919>;
@@ -349,7 +365,8 @@ i2c5: i2c@e66e0000 {
 		i2c6: i2c@e66e8000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7796";
+			compatible = "renesas,i2c-r8a7796",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe66e8000 0 0x40>;
 			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 918>;
@@ -360,6 +377,104 @@ i2c6: i2c@e66e8000 {
 			status = "disabled";
 		};

+		can0: can@e6c30000 {
+			compatible = "renesas,can-r8a7796",
+				     "renesas,rcar-gen3-can";
+			reg = <0 0xe6c30000 0 0x1000>;
+			interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 916>,
+			       <&cpg CPG_CORE R8A7796_CLK_CANFD>,
+			       <&can_clk>;
+			clock-names = "clkp1", "clkp2", "can_clk";
+			assigned-clocks = <&cpg CPG_CORE R8A7796_CLK_CANFD>;
+			assigned-clock-rates = <40000000>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
+		can1: can@e6c38000 {
+			compatible = "renesas,can-r8a7796",
+				     "renesas,rcar-gen3-can";
+			reg = <0 0xe6c38000 0 0x1000>;
+			interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 915>,
+			       <&cpg CPG_CORE R8A7796_CLK_CANFD>,
+			       <&can_clk>;
+			clock-names = "clkp1", "clkp2", "can_clk";
+			assigned-clocks = <&cpg CPG_CORE R8A7796_CLK_CANFD>;
+			assigned-clock-rates = <40000000>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
+		canfd: can@e66c0000 {
+			compatible = "renesas,r8a7796-canfd",
+				     "renesas,rcar-gen3-canfd";
+			reg = <0 0xe66c0000 0 0x8000>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+				   <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 914>,
+			       <&cpg CPG_CORE R8A7796_CLK_CANFD>,
+			       <&can_clk>;
+			clock-names = "fck", "canfd", "can_clk";
+			assigned-clocks = <&cpg CPG_CORE R8A7796_CLK_CANFD>;
+			assigned-clock-rates = <40000000>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			status = "disabled";
+
+			channel0 {
+				status = "disabled";
+			};
+
+			channel1 {
+				status = "disabled";
+			};
+		};
+
+		avb: ethernet@e6800000 {
+			compatible = "renesas,etheravb-r8a7796",
+				     "renesas,etheravb-rcar-gen3";
+			reg = <0 0xe6800000 0 0x800>, <0 0xe6a00000 0 0x10000>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch11",
+					  "ch12", "ch13", "ch14", "ch15",
+					  "ch16", "ch17", "ch18", "ch19",
+					  "ch20", "ch21", "ch22", "ch23",
+					  "ch24";
+			clocks = <&cpg CPG_MOD 812>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			phy-mode = "rgmii-id";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		scif2: serial@e6e88000 {
 			compatible = "renesas,scif-r8a7796",
 				     "renesas,rcar-gen3-scif", "renesas,scif";
@@ -373,6 +488,64 @@ scif2: serial@e6e88000 {
 			status = "disabled";
 		};

+		msiof0: spi@e6e90000 {
+			compatible = "renesas,msiof-r8a7796",
+				     "renesas,rcar-gen3-msiof";
+			reg = <0 0xe6e90000 0 0x0064>;
+			interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 211>;
+			dmas = <&dmac1 0x41>, <&dmac1 0x40>,
+			       <&dmac2 0x41>, <&dmac2 0x40>;
+			dma-names = "tx", "rx";
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		msiof1: spi@e6ea0000 {
+			compatible = "renesas,msiof-r8a7796",
+				     "renesas,rcar-gen3-msiof";
+			reg = <0 0xe6ea0000 0 0x0064>;
+			interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 210>;
+			dmas = <&dmac1 0x43>, <&dmac1 0x42>,
+			       <&dmac2 0x43>, <&dmac2 0x42>;
+			dma-names = "tx", "rx";
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		msiof2: spi@e6c00000 {
+			compatible = "renesas,msiof-r8a7796",
+				     "renesas,rcar-gen3-msiof";
+			reg = <0 0xe6c00000 0 0x0064>;
+			interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 209>;
+			dmas = <&dmac0 0x45>, <&dmac0 0x44>;
+			dma-names = "tx", "rx";
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		msiof3: spi@e6c10000 {
+			compatible = "renesas,msiof-r8a7796",
+				     "renesas,rcar-gen3-msiof";
+			reg = <0 0xe6c10000 0 0x0064>;
+			interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 208>;
+			dmas = <&dmac0 0x47>, <&dmac0 0x46>;
+			dma-names = "tx", "rx";
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		dmac0: dma-controller@e6700000 {
 			compatible = "renesas,dmac-r8a7796",
 				     "renesas,rcar-dmac";
@@ -511,5 +684,63 @@ sdhi3: sd@ee160000 {
 			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
 			status = "disabled";
 		};
+
+		tsc: thermal@e6198000 {
+			compatible = "renesas,r8a7796-thermal";
+			reg = <0 0xe6198000 0 0x68>,
+			      <0 0xe61a0000 0 0x5c>,
+			      <0 0xe61a8000 0 0x5c>;
+			interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 522>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			#thermal-sensor-cells = <1>;
+			status = "okay";
+		};
+
+		thermal-zones {
+			sensor_thermal1: sensor-thermal1 {
+				polling-delay-passive = <250>;
+				polling-delay = <1000>;
+				thermal-sensors = <&tsc 0>;
+
+				trips {
+					sensor1_crit: sensor1-crit {
+						temperature = <120000>;
+						hysteresis = <2000>;
+						type = "critical";
+					};
+				};
+			};
+
+			sensor_thermal2: sensor-thermal2 {
+				polling-delay-passive = <250>;
+				polling-delay = <1000>;
+				thermal-sensors = <&tsc 1>;
+
+				trips {
+					sensor2_crit: sensor2-crit {
+						temperature = <120000>;
+						hysteresis = <2000>;
+						type = "critical";
+					};
+				};
+			};
+
+			sensor_thermal3: sensor-thermal3 {
+				polling-delay-passive = <250>;
+				polling-delay = <1000>;
+				thermal-sensors = <&tsc 2>;
+
+				trips {
+					sensor3_crit: sensor3-crit {
+						temperature = <120000>;
+						hysteresis = <2000>;
+						type = "critical";
+					};
+				};
+			};
+		};
 	};
 };
--- a/arch/arm64/boot/dts/rockchip/rk3368-evb.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3368-evb.dtsi
@@ -90,7 +90,7 @@ backlight: backlight {
 			240 241 242 243 244 245 246 247
 			248 249 250 251 252 253 254 255>;
 		default-brightness-level = <128>;
-		enable-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+		enable-gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&bl_en>;
 		pwms = <&pwm0 0 1000000 PWM_POLARITY_INVERTED>;
@@ -101,7 +101,7 @@ emmc_pwrseq: emmc-pwrseq {
 		compatible = "mmc-pwrseq-emmc";
 		pinctrl-0 = <&emmc_reset>;
 		pinctrl-names = "default";
-		reset-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio2 RK_PA3 GPIO_ACTIVE_HIGH>;
 	};

 	keys: gpio-keys {
@@ -111,7 +111,7 @@ keys: gpio-keys {

 		power {
 			wakeup-source;
-			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
 			label = "GPIO Power";
 			linux,code = <KEY_POWER>;
 		};
@@ -121,7 +121,7 @@ power {
 	vcc_host: vcc-host-regulator {
 		compatible = "regulator-fixed";
 		enable-active-high;
-		gpio = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+		gpio = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&host_vbus_drv>;
 		regulator-name = "vcc_host";
@@ -166,7 +166,7 @@ &gmac {
 	phy-supply = <&vcc_lan>;
 	phy-mode = "rmii";
 	clock_in_out = "output";
-	snps,reset-gpio = <&gpio3 12 0>;
+	snps,reset-gpio = <&gpio3 RK_PB4 GPIO_ACTIVE_HIGH>;
 	snps,reset-active-low;
 	snps,reset-delays-us = <0 10000 1000000>;
 	pinctrl-names = "default";

--- a/arch/arm64/boot/dts/rockchip/rk3368-geekbox.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3368-geekbox.dts
@@ -66,7 +66,7 @@ ext_gmac: gmac-clk {

 	ir: ir-receiver {
 		compatible = "gpio-ir-receiver";
-		gpios = <&gpio3 30 GPIO_ACTIVE_LOW>;
+		gpios = <&gpio3 RK_PD6 GPIO_ACTIVE_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&ir_int>;
 	};
@@ -77,7 +77,7 @@ keys: gpio-keys {
 		pinctrl-0 = <&pwr_key>;

 		power {
-			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
 			label = "GPIO Power";
 			linux,code = <KEY_POWER>;
 			wakeup-source;
@@ -88,13 +88,13 @@ leds: gpio-leds {
 		compatible = "gpio-leds";

 		blue {
-			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_HIGH>;
 			label = "geekbox:blue:led";
 			default-state = "on";
 		};

 		red {
-			gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpio2 RK_PA3 GPIO_ACTIVE_HIGH>;
 			label = "geekbox:red:led";
 			default-state = "off";
 		};
@@ -146,7 +146,7 @@ rk808: pmic@1b {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pmic_int>, <&pmic_sleep>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+		interrupts = <RK_PA5 IRQ_TYPE_LEVEL_LOW>;
 		rockchip,system-power-controller;
 		vcc1-supply = <&vcc_sys>;
 		vcc2-supply = <&vcc_sys>;

--- a/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
@@ -61,7 +61,7 @@ emmc_pwrseq: emmc-pwrseq {
 		compatible = "mmc-pwrseq-emmc";
 		pinctrl-0 = <&emmc_reset>;
 		pinctrl-names = "default";
-		reset-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio2 RK_PA3 GPIO_ACTIVE_HIGH>;
 	};

 	ext_gmac: external-gmac-clock {
@@ -78,7 +78,7 @@ keys: gpio-keys {

 		power {
 			wakeup-source;
-			gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
 			label = "GPIO Power";
 			linux,code = <KEY_POWER>;
 		};
@@ -88,7 +88,7 @@ leds: gpio-leds {
 		compatible = "gpio-leds";

 		red {
-			gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpio3 RK_PD5 GPIO_ACTIVE_HIGH>;
 			label = "orion:red:led";
 			pinctrl-names = "default";
 			pinctrl-0 = <&led_ctl>;
@@ -96,7 +96,7 @@ red {
 		};

 		blue {
-			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
 			label = "orion:blue:led";
 			pinctrl-names = "default";
 			pinctrl-0 = <&stby_pwren>;
@@ -117,7 +117,7 @@ vcc_18: vcc18-regulator {
 	/* supplies both host and otg */
 	vcc_host: vcc-host-regulator {
 		compatible = "regulator-fixed";
-		gpio = <&gpio0 4 GPIO_ACTIVE_LOW>;
+		gpio = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&host_vbus_drv>;
 		regulator-name = "vcc_host";
@@ -149,7 +149,7 @@ vcc_lan: vcc-lan-regulator {
 	vcc_sd: vcc-sd-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc_sd";
-		gpio = <&gpio3 11 GPIO_ACTIVE_LOW>;
+		gpio = <&gpio3 RK_PB3 GPIO_ACTIVE_LOW>;
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <3300000>;
 		vin-supply = <&vcc_io>;
@@ -217,7 +217,7 @@ &gmac {
 	phy-mode = "rgmii";
 	pinctrl-names = "default";
 	pinctrl-0 = <&rgmii_pins>;
-	snps,reset-gpio = <&gpio3 12 0>;
+	snps,reset-gpio = <&gpio3 RK_PB4 GPIO_ACTIVE_HIGH>;
 	snps,reset-active-low;
 	snps,reset-delays-us = <0 10000 1000000>;
 	tx_delay = <0x30>;

--- a/arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dts
@@ -63,7 +63,7 @@ keys: gpio-keys {
 		pinctrl-0 = <&pwr_key>;

 		power {
-			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
 			label = "GPIO Power";
 			linux,code = <KEY_POWER>;
 			wakeup-source;
@@ -105,7 +105,7 @@ rk808: pmic@1b {
 		compatible = "rockchip,rk808";
 		reg = <0x1b>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+		interrupts = <RK_PA5 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pmic_int>, <&pmic_sleep>;
 		rockchip,system-power-controller;
@@ -236,7 +236,7 @@ accelerometer@18 {
 		compatible = "bosch,bma250";
 		reg = <0x18>;
 		interrupt-parent = <&gpio2>;
-		interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+		interrupts = <RK_PC1 IRQ_TYPE_LEVEL_LOW>;
 	};
 };

@@ -247,8 +247,8 @@ gsl1680: touchscreen@40 {
 		compatible = "silead,gsl1680";
 		reg = <0x40>;
 		interrupt-parent = <&gpio3>;
-		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
-		power-gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PD4 IRQ_TYPE_EDGE_FALLING>;
+		power-gpios = <&gpio3 RK_PB7 GPIO_ACTIVE_HIGH>;
 		touchscreen-size-x = <800>;
 		touchscreen-size-y = <1280>;
 		silead,max-fingers = <5>;

--- a/arch/arm64/boot/dts/rockchip/rk3368-r88.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3368-r88.dts
@@ -61,7 +61,7 @@ emmc_pwrseq: emmc-pwrseq {
 		compatible = "mmc-pwrseq-emmc";
 		pinctrl-0 = <&emmc_reset>;
 		pinctrl-names = "default";
-		reset-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio2 RK_PA3 GPIO_ACTIVE_HIGH>;
 	};

 	keys: gpio-keys {
@@ -71,7 +71,7 @@ keys: gpio-keys {

 		power {
 			wakeup-source;
-			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
 			label = "GPIO Power";
 			linux,code = <KEY_POWER>;
 		};
@@ -81,7 +81,7 @@ leds: gpio-leds {
 		compatible = "gpio-leds";

 		work {
-			gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpio3 RK_PD5 GPIO_ACTIVE_HIGH>;
 			label = "r88:green:led";
 			pinctrl-names = "default";
 			pinctrl-0 = <&led_ctl>;
@@ -90,7 +90,7 @@ work {

 	ir: ir-receiver {
 		compatible = "gpio-ir-receiver";
-		gpios = <&gpio3 30 GPIO_ACTIVE_LOW>;
+		gpios = <&gpio3 RK_PD6 GPIO_ACTIVE_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&ir_int>;
 	};
@@ -104,10 +104,10 @@ sdio_pwrseq: sdio-pwrseq {

 		reset-gpios =
 			/* BT_RST_N */
-			<&gpio3 5 GPIO_ACTIVE_LOW>,
+			<&gpio3 RK_PA5 GPIO_ACTIVE_LOW>,

 			/* WL_REG_ON */
-			<&gpio3 4 GPIO_ACTIVE_LOW>;
+			<&gpio3 RK_PA4 GPIO_ACTIVE_LOW>;
 	};

 	vcc_18: vcc18-regulator {
@@ -124,7 +124,7 @@ vcc_18: vcc18-regulator {
 	vcc_host: vcc-host-regulator {
 		compatible = "regulator-fixed";
 		enable-active-high;
-		gpio = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+		gpio = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&host_vbus_drv>;
 		regulator-name = "vcc_host";
@@ -199,7 +199,7 @@ &gmac {
 	phy-supply = <&vcc_lan>;
 	phy-mode = "rmii";
 	clock_in_out = "output";
-	snps,reset-gpio = <&gpio3 12 0>;
+	snps,reset-gpio = <&gpio3 RK_PB4 GPIO_ACTIVE_HIGH>;
 	snps,reset-active-low;
 	snps,reset-delays-us = <0 10000 1000000>;
 	pinctrl-names = "default";

--- a/arch/arm64/boot/dts/rockchip/rk3399-evb.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-evb.dts
@@ -85,7 +85,7 @@ backlight: backlight {
 			240 241 242 243 244 245 246 247
 			248 249 250 251 252 253 254 255>;
 		default-brightness-level = <200>;
-		enable-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+		enable-gpios = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
 		pwms = <&pwm0 0 25000 0>;
 	};

@@ -128,7 +128,7 @@ vcc5v0_sys: vcc5v0-sys {
 	vcc5v0_host: vcc5v0-host-regulator {
 		compatible = "regulator-fixed";
 		enable-active-high;
-		gpio = <&gpio4 25 GPIO_ACTIVE_HIGH>;
+		gpio = <&gpio4 RK_PD1 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&vcc5v0_host_en>;
 		regulator-name = "vcc5v0_host";
@@ -163,7 +163,7 @@ &gmac {
 	phy-mode = "rgmii";
 	pinctrl-names = "default";
 	pinctrl-0 = <&rgmii_pins>;
-	snps,reset-gpio = <&gpio3 15 GPIO_ACTIVE_LOW>;
+	snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
 	snps,reset-active-low;
 	snps,reset-delays-us = <0 10000 50000>;
 	tx_delay = <0x28>;
@@ -196,7 +196,7 @@ &pcie_phy {
 };

 &pcie0 {
-	ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+	ep-gpios = <&gpio3 RK_PB5 GPIO_ACTIVE_HIGH>;
 	num-lanes = <4>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pcie_clkreqn>;

--- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
@@ -283,6 +283,7 @@ pcie0: pcie@f8000000 {
 		#address-cells = <3>;
 		#size-cells = <2>;
 		#interrupt-cells = <1>;
+		aspm-no-l0s;
 		bus-range = <0x0 0x1>;
 		clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>,
 			 <&cru PCLK_PCIE>, <&cru SCLK_PCIE_PM>;
@@ -297,6 +298,7 @@ pcie0: pcie@f8000000 {
 				<0 0 0 2 &pcie0_intc 1>,
 				<0 0 0 3 &pcie0_intc 2>,
 				<0 0 0 4 &pcie0_intc 3>;
+		max-link-speed = <1>;
 		msi-map = <0x0 &its 0x0 0x1000>;
 		phys = <&pcie_phy>;
 		phy-names = "pcie-phy";
@@ -321,8 +323,10 @@ usb_host0_ehci: usb@fe380000 {
 		compatible = "generic-ehci";
 		reg = <0x0 0xfe380000 0x0 0x20000>;
 		interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH 0>;
-		clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>;
-		clock-names = "hclk_host0", "hclk_host0_arb";
+		clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>,
+			 <&u2phy0>;
+		clock-names = "usbhost", "arbiter",
+			      "utmi";
 		phys = <&u2phy0_host>;
 		phy-names = "usb";
 		status = "disabled";
@@ -332,8 +336,12 @@ usb_host0_ohci: usb@fe3a0000 {
 		compatible = "generic-ohci";
 		reg = <0x0 0xfe3a0000 0x0 0x20000>;
 		interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH 0>;
-		clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>;
-		clock-names = "hclk_host0", "hclk_host0_arb";
+		clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>,
+			 <&u2phy0>;
+		clock-names = "usbhost", "arbiter",
+			      "utmi";
+		phys = <&u2phy0_host>;
+		phy-names = "usb";
 		status = "disabled";
 	};

@@ -341,8 +349,10 @@ usb_host1_ehci: usb@fe3c0000 {
 		compatible = "generic-ehci";
 		reg = <0x0 0xfe3c0000 0x0 0x20000>;
 		interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH 0>;
-		clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>;
-		clock-names = "hclk_host1", "hclk_host1_arb";
+		clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>,
+			 <&u2phy1>;
+		clock-names = "usbhost", "arbiter",
+			      "utmi";
 		phys = <&u2phy1_host>;
 		phy-names = "usb";
 		status = "disabled";
@@ -352,8 +362,12 @@ usb_host1_ohci: usb@fe3e0000 {
 		compatible = "generic-ohci";
 		reg = <0x0 0xfe3e0000 0x0 0x20000>;
 		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH 0>;
-		clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>;
-		clock-names = "hclk_host1", "hclk_host1_arb";
+		clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>,
+			 <&u2phy1>;
+		clock-names = "usbhost", "arbiter",
+			      "utmi";
+		phys = <&u2phy1_host>;
+		phy-names = "usb";
 		status = "disabled";
 	};

@@ -607,7 +621,7 @@ spi5: spi@ff200000 {
 		status = "disabled";
 	};

-	thermal-zones {
+	thermal_zones: thermal-zones {
 		cpu_thermal: cpu {
 			polling-delay-passive = <100>;
 			polling-delay = <1000>;
@@ -1077,6 +1091,7 @@ wafer_info: wafer-info@1c {
 	pmucru: pmu-clock-controller@ff750000 {
 		compatible = "rockchip,rk3399-pmucru";
 		reg = <0x0 0xff750000 0x0 0x1000>;
+		rockchip,grf = <&pmugrf>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
 		assigned-clocks = <&pmucru PLL_PPLL>;
@@ -1086,6 +1101,7 @@ pmucru: pmu-clock-controller@ff750000 {
 	cru: clock-controller@ff760000 {
 		compatible = "rockchip,rk3399-cru";
 		reg = <0x0 0xff760000 0x0 0x1000>;
+		rockchip,grf = <&grf>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
 		assigned-clocks =
@@ -1436,6 +1452,13 @@ clk_32k: clk-32k {
 			};
 		};

+		edp {
+			edp_hpd: edp-hpd {
+				rockchip,pins =
+					<4 23 RK_FUNC_2 &pcfg_pull_none>;
+			};
+		};
+
 		gmac {
 			rgmii_pins: rgmii-pins {
 				rockchip,pins =

--- a/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi
@@ -273,6 +273,17 @@ smpctrl@59800000 {
 			reg = <0x59801000 0x400>;
 		};

+		sdctrl@59810000 {
+			compatible = "socionext,uniphier-ld11-sdctrl",
+				     "simple-mfd", "syscon";
+			reg = <0x59810000 0x400>;
+
+			sd_rst: reset {
+				compatible = "socionext,uniphier-ld11-sd-reset";
+				#reset-cells = <1>;
+			};
+		};
+
 		perictrl@59820000 {
 			compatible = "socionext,uniphier-ld11-perictrl",
 				     "simple-mfd", "syscon";
@@ -289,6 +300,16 @@ peri_rst: reset {
 			};
 		};

+		emmc: sdhc@5a000000 {
+			compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc";
+			reg = <0x5a000000 0x400>;
+			interrupts = <0 78 4>;
+			clocks = <&sys_clk 4>;
+			bus-width = <8>;
+			mmc-ddr-1_8v;
+			mmc-hs200-1_8v;
+		};
+
 		usb0: usb@5a800100 {
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";

--- a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
@@ -374,6 +374,16 @@ peri_rst: reset {
 			};
 		};

+		emmc: sdhc@5a000000 {
+			compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc";
+			reg = <0x5a000000 0x400>;
+			interrupts = <0 78 4>;
+			clocks = <&sys_clk 4>;
+			bus-width = <8>;
+			mmc-ddr-1_8v;
+			mmc-hs200-1_8v;
+		};
+
 		soc-glue@5f800000 {
 			compatible = "socionext,uniphier-ld20-soc-glue",
 				     "simple-mfd", "syscon";

--- a/arch/arm64/boot/dts/zte/zx296718.dtsi
+++ b/arch/arm64/boot/dts/zte/zx296718.dtsi
@@ -44,6 +44,7 @@
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/zx296718-clock.h>

 / {
 	compatible = "zte,zx296718";
@@ -81,6 +82,8 @@ cpu0: cpu@0 {
 			compatible = "arm,cortex-a53","arm,armv8";
 			reg = <0x0 0x0>;
 			enable-method = "psci";
+			clocks = <&topcrm A53_GATE>;
+			operating-points-v2 = <&cluster0_opp>;
 		};

 		cpu1: cpu@1 {
@@ -88,6 +91,8 @@ cpu1: cpu@1 {
 			compatible = "arm,cortex-a53","arm,armv8";
 			reg = <0x0 0x1>;
 			enable-method = "psci";
+			clocks = <&topcrm A53_GATE>;
+			operating-points-v2 = <&cluster0_opp>;
 		};

 		cpu2: cpu@2 {
@@ -95,6 +100,8 @@ cpu2: cpu@2 {
 			compatible = "arm,cortex-a53","arm,armv8";
 			reg = <0x0 0x2>;
 			enable-method = "psci";
+			clocks = <&topcrm A53_GATE>;
+			operating-points-v2 = <&cluster0_opp>;
 		};

 		cpu3: cpu@3 {
@@ -102,6 +109,38 @@ cpu3: cpu@3 {
 			compatible = "arm,cortex-a53","arm,armv8";
 			reg = <0x0 0x3>;
 			enable-method = "psci";
+			clocks = <&topcrm A53_GATE>;
+			operating-points-v2 = <&cluster0_opp>;
+		};
+	};
+
+	cluster0_opp: opp-table0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp@500000000 {
+			opp-hz = /bits/ 64 <500000000>;
+			clock-latency-ns = <500000>;
+		};
+
+		opp@648000000 {
+			opp-hz = /bits/ 64 <648000000>;
+			clock-latency-ns = <500000>;
+		};
+
+		opp@800000000 {
+			opp-hz = /bits/ 64 <800000000>;
+			clock-latency-ns = <500000>;
+		};
+
+		opp@1000000000 {
+			opp-hz = /bits/ 64 <1000000000>;
+			clock-latency-ns = <500000>;
+		};
+
+		opp@1188000000 {
+			opp-hz = /bits/ 64 <1188000000>;
+			clock-latency-ns = <500000>;
 		};
 	};


--- a/include/dt-bindings/pinctrl/samsung.h
+++ b/include/dt-bindings/pinctrl/samsung.h
@@ -45,6 +45,20 @@
 #define EXYNOS5420_PIN_DRV_LV3		2
 #define EXYNOS5420_PIN_DRV_LV4		3

+/* Drive strengths for Exynos5433 */
+#define EXYNOS5433_PIN_DRV_FAST_SR1	0
+#define EXYNOS5433_PIN_DRV_FAST_SR2	1
+#define EXYNOS5433_PIN_DRV_FAST_SR3	2
+#define EXYNOS5433_PIN_DRV_FAST_SR4	3
+#define EXYNOS5433_PIN_DRV_FAST_SR5	4
+#define EXYNOS5433_PIN_DRV_FAST_SR6	5
+#define EXYNOS5433_PIN_DRV_SLOW_SR1	8
+#define EXYNOS5433_PIN_DRV_SLOW_SR2	9
+#define EXYNOS5433_PIN_DRV_SLOW_SR3	0xa
+#define EXYNOS5433_PIN_DRV_SLOW_SR4	0xb
+#define EXYNOS5433_PIN_DRV_SLOW_SR5	0xc
+#define EXYNOS5433_PIN_DRV_SLOW_SR6	0xf
+
 #define EXYNOS_PIN_FUNC_INPUT		0
 #define EXYNOS_PIN_FUNC_OUTPUT		1
 #define EXYNOS_PIN_FUNC_2		2