sfc: Export fibre-specific supported link modes

The 1/10GbaseT modes were set up for cards with SFP+ cages in
3497ed8c ("sfc: report supported link speeds on SFP connections").
10GbaseT was likely used since no 10G fibre mode existed.

The missing fibre modes for 1/10G were added to ethtool.h in 5711a982
("net: ethtool: add support for 1000BaseX and missing 10G link modes")
shortly thereafter.

The user guide available at https://support-nic.xilinx.com/wp/drivers
lists support for the following cable and transceiver types in section 2.9:
- QSFP28 100G Direct Attach Cables
- QSFP28 100G SR Optical Transceivers (with SR4 modules listed)
- SFP28 25G Direct Attach Cables
- SFP28 25G SR Optical Transceivers
- QSFP+ 40G Direct Attach Cables
- QSFP+ 40G Active Optical Cables
- QSFP+ 40G SR4 Optical Transceivers
- QSFP+ to SFP+ Breakout Direct Attach Cables
- QSFP+ to SFP+ Breakout Active Optical Cables
- SFP+ 10G Direct Attach Cables
- SFP+ 10G SR Optical Transceivers
- SFP+ 10G LR Optical Transceivers
- SFP 1000BASE‐T Transceivers
- 1G Optical Transceivers
(From user guide issue 28. Issue 16 which also includes older cards like
SFN5xxx/SFN6xxx has matching lists for 1/10/40G transceiver types.)

Regarding SFP+ 10GBASE‐T transceivers the latest guide says:
"Solarflare adapters do not support 10GBASE‐T transceiver modules."

Tested using SFN5122F-R7 (with 2 SFP+ ports). Supported link modes do not change
depending on module used (tested with 1000BASE-T, 1000BASE-BX10, 10GBASE-LR).
Before:

$ ethtool ext
Settings for ext:
	Supported ports: [ FIBRE ]
	Supported link modes:   1000baseT/Full
	                        10000baseT/Full
	Supported pause frame use: Symmetric Receive-only
	Supports auto-negotiation: No
	Supported FEC modes: Not reported
	Advertised link modes:  Not reported
	Advertised pause frame use: No
	Advertised auto-negotiation: No
	Advertised FEC modes: Not reported
	Link partner advertised link modes:  Not reported
	Link partner advertised pause frame use: No
	Link partner advertised auto-negotiation: No
	Link partner advertised FEC modes: Not reported
	Speed: 1000Mb/s
	Duplex: Full
	Auto-negotiation: off
	Port: FIBRE
	PHYAD: 255
	Transceiver: internal
        Current message level: 0x000020f7 (8439)
                               drv probe link ifdown ifup rx_err tx_err hw
	Link detected: yes

After:

$ ethtool ext
Settings for ext:
	Supported ports: [ FIBRE ]
	Supported link modes:   1000baseT/Full
	                        1000baseX/Full
	                        10000baseCR/Full
	                        10000baseSR/Full
	                        10000baseLR/Full
	Supported pause frame use: Symmetric Receive-only
	Supports auto-negotiation: No
	Supported FEC modes: Not reported
	Advertised link modes:  Not reported
	Advertised pause frame use: No
	Advertised auto-negotiation: No
	Advertised FEC modes: Not reported
	Link partner advertised link modes:  Not reported
	Link partner advertised pause frame use: No
	Link partner advertised auto-negotiation: No
	Link partner advertised FEC modes: Not reported
	Speed: 1000Mb/s
	Duplex: Full
	Auto-negotiation: off
	Port: FIBRE
	PHYAD: 255
	Transceiver: internal
	Supports Wake-on: g
	Wake-on: d
        Current message level: 0x000020f7 (8439)
                               drv probe link ifdown ifup rx_err tx_err hw
	Link detected: yes
Signed-off-by: Erik Ekman <erik@kryo.se>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/sfc/mcdi_port_common.c

@@ -132,16 +132,27 @@ void mcdi_to_ethtool_linkset(u32 media, u32 cap, unsigned long *linkset)
 	case MC_CMD_MEDIA_SFP_PLUS:
 	case MC_CMD_MEDIA_QSFP_PLUS:
 		SET_BIT(FIBRE);
-		if (cap & (1 << MC_CMD_PHY_CAP_1000FDX_LBN))
+		if (cap & (1 << MC_CMD_PHY_CAP_1000FDX_LBN)) {
 			SET_BIT(1000baseT_Full);
-		if (cap & (1 << MC_CMD_PHY_CAP_10000FDX_LBN))
-			SET_BIT(10000baseT_Full);
-		if (cap & (1 << MC_CMD_PHY_CAP_40000FDX_LBN))
+			SET_BIT(1000baseX_Full);
+		}
+		if (cap & (1 << MC_CMD_PHY_CAP_10000FDX_LBN)) {
+			SET_BIT(10000baseCR_Full);
+			SET_BIT(10000baseLR_Full);
+			SET_BIT(10000baseSR_Full);
+		}
+		if (cap & (1 << MC_CMD_PHY_CAP_40000FDX_LBN)) {
 			SET_BIT(40000baseCR4_Full);
-		if (cap & (1 << MC_CMD_PHY_CAP_100000FDX_LBN))
+			SET_BIT(40000baseSR4_Full);
+		}
+		if (cap & (1 << MC_CMD_PHY_CAP_100000FDX_LBN)) {
 			SET_BIT(100000baseCR4_Full);
-		if (cap & (1 << MC_CMD_PHY_CAP_25000FDX_LBN))
+			SET_BIT(100000baseSR4_Full);
+		}
+		if (cap & (1 << MC_CMD_PHY_CAP_25000FDX_LBN)) {
 			SET_BIT(25000baseCR_Full);
+			SET_BIT(25000baseSR_Full);
+		}
 		if (cap & (1 << MC_CMD_PHY_CAP_50000FDX_LBN))
 			SET_BIT(50000baseCR2_Full);
 		break;
@@ -192,15 +203,19 @@ u32 ethtool_linkset_to_mcdi_cap(const unsigned long *linkset)
 		result |= (1 << MC_CMD_PHY_CAP_100FDX_LBN);
 	if (TEST_BIT(1000baseT_Half))
 		result |= (1 << MC_CMD_PHY_CAP_1000HDX_LBN);
-	if (TEST_BIT(1000baseT_Full) || TEST_BIT(1000baseKX_Full))
+	if (TEST_BIT(1000baseT_Full) || TEST_BIT(1000baseKX_Full) ||
+			TEST_BIT(1000baseX_Full))
 		result |= (1 << MC_CMD_PHY_CAP_1000FDX_LBN);
-	if (TEST_BIT(10000baseT_Full) || TEST_BIT(10000baseKX4_Full))
+	if (TEST_BIT(10000baseT_Full) || TEST_BIT(10000baseKX4_Full) ||
+			TEST_BIT(10000baseCR_Full) || TEST_BIT(10000baseLR_Full) ||
+			TEST_BIT(10000baseSR_Full))
 		result |= (1 << MC_CMD_PHY_CAP_10000FDX_LBN);
-	if (TEST_BIT(40000baseCR4_Full) || TEST_BIT(40000baseKR4_Full))
+	if (TEST_BIT(40000baseCR4_Full) || TEST_BIT(40000baseKR4_Full) ||
+			TEST_BIT(40000baseSR4_Full))
 		result |= (1 << MC_CMD_PHY_CAP_40000FDX_LBN);
-	if (TEST_BIT(100000baseCR4_Full))
+	if (TEST_BIT(100000baseCR4_Full) || TEST_BIT(100000baseSR4_Full))
 		result |= (1 << MC_CMD_PHY_CAP_100000FDX_LBN);
-	if (TEST_BIT(25000baseCR_Full))
+	if (TEST_BIT(25000baseCR_Full) || TEST_BIT(25000baseSR_Full))
 		result |= (1 << MC_CMD_PHY_CAP_25000FDX_LBN);
 	if (TEST_BIT(50000baseCR2_Full))
 		result |= (1 << MC_CMD_PHY_CAP_50000FDX_LBN);