hwmon: add driver for the Microchip LAN966x SoC

Add support for the temperatur sensor and the fan controller on the
Microchip LAN966x SoC. Apparently, an Analog Bits PVT sensor is used
which can measure temperature and process voltages. But only a forumlae
for the temperature sensor is known. Additionally, the SoC support a fan
tacho input as well as a PWM signal to control the fan.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220401214032.3738095-5-michael@walle.cc
[groeck: Added missing reference in Documentation/hwmon/index.rst]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Documentation/hwmon/index.rst

@@ -90,6 +90,7 @@ Hardware Monitoring Kernel Drivers
    jc42
    k10temp
    k8temp
+   lan966x
    lineage-pem
    lm25066
    lm63

Documentation/hwmon/lan966x.rst

+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver lan966x-hwmon
+===========================
+
+Supported chips:
+
+  * Microchip LAN9668 (sensor in SoC)
+
+    Prefix: 'lan9668-hwmon'
+
+    Datasheet: https://microchip-ung.github.io/lan9668_reginfo
+
+Authors:
+
+	Michael Walle <michael@walle.cc>
+
+Description
+-----------
+
+This driver implements support for the Microchip LAN9668 on-chip
+temperature sensor as well as its fan controller. It provides one
+temperature sensor and one fan controller. The temperature range
+of the sensor is specified from -40 to +125 degrees Celsius and
+its accuracy is +/- 5 degrees Celsius. The fan controller has a
+tacho input and a PWM output with a customizable PWM output
+frequency ranging from ~20Hz to ~650kHz.
+
+No alarms are supported by the SoC.
+
+The driver exports temperature values, fan tacho input and PWM
+settings via the following sysfs files:
+
+**temp1_input**
+
+**fan1_input**
+
+**pwm1**
+
+**pwm1_freq**

drivers/hwmon/Kconfig

@@ -819,6 +819,18 @@ config SENSORS_POWR1220
 	  This driver can also be built as a module. If so, the module
 	  will be called powr1220.
 
+config SENSORS_LAN966X
+	tristate "Microchip LAN966x Hardware Monitoring"
+	depends on SOC_LAN966 || COMPILE_TEST
+	select REGMAP
+	select POLYNOMIAL
+	help
+	  If you say yes here you get support for temperature monitoring
+	  on the Microchip LAN966x SoC.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called lan966x-hwmon.
+
 config SENSORS_LINEAGE
 	tristate "Lineage Compact Power Line Power Entry Module"
 	depends on I2C

drivers/hwmon/Makefile

@@ -100,6 +100,7 @@ obj-$(CONFIG_SENSORS_IT87)	+= it87.o
 obj-$(CONFIG_SENSORS_JC42)	+= jc42.o
 obj-$(CONFIG_SENSORS_K8TEMP)	+= k8temp.o
 obj-$(CONFIG_SENSORS_K10TEMP)	+= k10temp.o
+obj-$(CONFIG_SENSORS_LAN966X)	+= lan966x-hwmon.o
 obj-$(CONFIG_SENSORS_LINEAGE)	+= lineage-pem.o
 obj-$(CONFIG_SENSORS_LOCHNAGAR)	+= lochnagar-hwmon.o
 obj-$(CONFIG_SENSORS_LM63)	+= lm63.o

drivers/hwmon/lan966x-hwmon.c

+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/hwmon.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+#include <linux/polynomial.h>
+#include <linux/regmap.h>
+
+/*
+ * The original translation formulae of the temperature (in degrees of Celsius)
+ * are as follows:
+ *
+ *   T = -3.4627e-11*(N^4) + 1.1023e-7*(N^3) + -1.9165e-4*(N^2) +
+ *       3.0604e-1*(N^1) + -5.6197e1
+ *
+ * where [-56.197, 136.402]C and N = [0, 1023].
+ *
+ * They must be accordingly altered to be suitable for the integer arithmetics.
+ * The technique is called 'factor redistribution', which just makes sure the
+ * multiplications and divisions are made so to have a result of the operations
+ * within the integer numbers limit. In addition we need to translate the
+ * formulae to accept millidegrees of Celsius. Here what it looks like after
+ * the alterations:
+ *
+ *   T = -34627e-12*(N^4) + 110230e-9*(N^3) + -191650e-6*(N^2) +
+ *       306040e-3*(N^1) + -56197
+ *
+ * where T = [-56197, 136402]mC and N = [0, 1023].
+ */
+
+static const struct polynomial poly_N_to_temp = {
+	.terms = {
+		{4,  -34627, 1000, 1},
+		{3,  110230, 1000, 1},
+		{2, -191650, 1000, 1},
+		{1,  306040, 1000, 1},
+		{0,  -56197,    1, 1}
+	}
+};
+
+#define PVT_SENSOR_CTRL		0x0 /* unused */
+#define PVT_SENSOR_CFG		0x4
+#define   SENSOR_CFG_CLK_CFG		GENMASK(27, 20)
+#define   SENSOR_CFG_TRIM_VAL		GENMASK(13, 9)
+#define   SENSOR_CFG_SAMPLE_ENA		BIT(8)
+#define   SENSOR_CFG_START_CAPTURE	BIT(7)
+#define   SENSOR_CFG_CONTINIOUS_MODE	BIT(6)
+#define   SENSOR_CFG_PSAMPLE_ENA	GENMASK(1, 0)
+#define PVT_SENSOR_STAT		0x8
+#define   SENSOR_STAT_DATA_VALID	BIT(10)
+#define   SENSOR_STAT_DATA		GENMASK(9, 0)
+
+#define FAN_CFG			0x0
+#define   FAN_CFG_DUTY_CYCLE		GENMASK(23, 16)
+#define   INV_POL			BIT(3)
+#define   GATE_ENA			BIT(2)
+#define   PWM_OPEN_COL_ENA		BIT(1)
+#define   FAN_STAT_CFG			BIT(0)
+#define FAN_PWM_FREQ		0x4
+#define   FAN_PWM_CYC_10US		GENMASK(25, 15)
+#define   FAN_PWM_FREQ_FREQ		GENMASK(14, 0)
+#define FAN_CNT			0xc
+#define   FAN_CNT_DATA			GENMASK(15, 0)
+
+#define LAN966X_PVT_CLK		1200000 /* 1.2 MHz */
+
+struct lan966x_hwmon {
+	struct regmap *regmap_pvt;
+	struct regmap *regmap_fan;
+	struct clk *clk;
+	unsigned long clk_rate;
+};
+
+static int lan966x_hwmon_read_temp(struct device *dev, long *val)
+{
+	struct lan966x_hwmon *hwmon = dev_get_drvdata(dev);
+	unsigned int data;
+	int ret;
+
+	ret = regmap_read(hwmon->regmap_pvt, PVT_SENSOR_STAT, &data);
+	if (ret < 0)
+		return ret;
+
+	if (!(data & SENSOR_STAT_DATA_VALID))
+		return -ENODATA;
+
+	*val = polynomial_calc(&poly_N_to_temp,
+			       FIELD_GET(SENSOR_STAT_DATA, data));
+
+	return 0;
+}
+
+static int lan966x_hwmon_read_fan(struct device *dev, long *val)
+{
+	struct lan966x_hwmon *hwmon = dev_get_drvdata(dev);
+	unsigned int data;
+	int ret;
+
+	ret = regmap_read(hwmon->regmap_fan, FAN_CNT, &data);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * Data is given in pulses per second. Assume two pulses
+	 * per revolution.
+	 */
+	*val = FIELD_GET(FAN_CNT_DATA, data) * 60 / 2;
+
+	return 0;
+}
+
+static int lan966x_hwmon_read_pwm(struct device *dev, long *val)
+{
+	struct lan966x_hwmon *hwmon = dev_get_drvdata(dev);
+	unsigned int data;
+	int ret;
+
+	ret = regmap_read(hwmon->regmap_fan, FAN_CFG, &data);
+	if (ret < 0)
+		return ret;
+
+	*val = FIELD_GET(FAN_CFG_DUTY_CYCLE, data);
+
+	return 0;
+}
+
+static int lan966x_hwmon_read_pwm_freq(struct device *dev, long *val)
+{
+	struct lan966x_hwmon *hwmon = dev_get_drvdata(dev);
+	unsigned long tmp;
+	unsigned int data;
+	int ret;
+
+	ret = regmap_read(hwmon->regmap_fan, FAN_PWM_FREQ, &data);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * Datasheet says it is sys_clk / 256 / pwm_freq. But in reality
+	 * it is sys_clk / 256 / (pwm_freq + 1).
+	 */
+	data = FIELD_GET(FAN_PWM_FREQ_FREQ, data) + 1;
+	tmp = DIV_ROUND_CLOSEST(hwmon->clk_rate, 256);
+	*val = DIV_ROUND_CLOSEST(tmp, data);
+
+	return 0;
+}
+
+static int lan966x_hwmon_read(struct device *dev, enum hwmon_sensor_types type,
+			      u32 attr, int channel, long *val)
+{
+	switch (type) {
+	case hwmon_temp:
+		return lan966x_hwmon_read_temp(dev, val);
+	case hwmon_fan:
+		return lan966x_hwmon_read_fan(dev, val);
+	case hwmon_pwm:
+		switch (attr) {
+		case hwmon_pwm_input:
+			return lan966x_hwmon_read_pwm(dev, val);
+		case hwmon_pwm_freq:
+			return lan966x_hwmon_read_pwm_freq(dev, val);
+		default:
+			return -EOPNOTSUPP;
+		}
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static int lan966x_hwmon_write_pwm(struct device *dev, long val)
+{
+	struct lan966x_hwmon *hwmon = dev_get_drvdata(dev);
+
+	if (val < 0 || val > 255)
+		return -EINVAL;
+
+	return regmap_update_bits(hwmon->regmap_fan, FAN_CFG,
+				  FAN_CFG_DUTY_CYCLE,
+				  FIELD_PREP(FAN_CFG_DUTY_CYCLE, val));
+}
+
+static int lan966x_hwmon_write_pwm_freq(struct device *dev, long val)
+{
+	struct lan966x_hwmon *hwmon = dev_get_drvdata(dev);
+
+	if (val <= 0)
+		return -EINVAL;
+
+	val = DIV_ROUND_CLOSEST(hwmon->clk_rate, val);
+	val = DIV_ROUND_CLOSEST(val, 256) - 1;
+	val = clamp_val(val, 0, FAN_PWM_FREQ_FREQ);
+
+	return regmap_update_bits(hwmon->regmap_fan, FAN_PWM_FREQ,
+				  FAN_PWM_FREQ_FREQ,
+				  FIELD_PREP(FAN_PWM_FREQ_FREQ, val));
+}
+
+static int lan966x_hwmon_write(struct device *dev, enum hwmon_sensor_types type,
+			       u32 attr, int channel, long val)
+{
+	switch (type) {
+	case hwmon_pwm:
+		switch (attr) {
+		case hwmon_pwm_input:
+			return lan966x_hwmon_write_pwm(dev, val);
+		case hwmon_pwm_freq:
+			return lan966x_hwmon_write_pwm_freq(dev, val);
+		default:
+			return -EOPNOTSUPP;
+		}
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static umode_t lan966x_hwmon_is_visible(const void *data,
+					enum hwmon_sensor_types type,
+					u32 attr, int channel)
+{
+	umode_t mode = 0;
+
+	switch (type) {
+	case hwmon_temp:
+		switch (attr) {
+		case hwmon_temp_input:
+			mode = 0444;
+			break;
+		default:
+			break;
+		}
+		break;
+	case hwmon_fan:
+		switch (attr) {
+		case hwmon_fan_input:
+			mode = 0444;
+			break;
+		default:
+			break;
+		}
+		break;
+	case hwmon_pwm:
+		switch (attr) {
+		case hwmon_pwm_input:
+		case hwmon_pwm_freq:
+			mode = 0644;
+			break;
+		default:
+			break;
+		}
+		break;
+	default:
+		break;
+	}
+
+	return mode;
+}
+
+static const struct hwmon_channel_info *lan966x_hwmon_info[] = {
+	HWMON_CHANNEL_INFO(chip, HWMON_C_REGISTER_TZ),
+	HWMON_CHANNEL_INFO(temp, HWMON_T_INPUT),
+	HWMON_CHANNEL_INFO(fan, HWMON_F_INPUT),
+	HWMON_CHANNEL_INFO(pwm, HWMON_PWM_INPUT | HWMON_PWM_FREQ),
+	NULL
+};
+
+static const struct hwmon_ops lan966x_hwmon_ops = {
+	.is_visible = lan966x_hwmon_is_visible,
+	.read = lan966x_hwmon_read,
+	.write = lan966x_hwmon_write,
+};
+
+static const struct hwmon_chip_info lan966x_hwmon_chip_info = {
+	.ops = &lan966x_hwmon_ops,
+	.info = lan966x_hwmon_info,
+};
+
+static void lan966x_hwmon_disable(void *data)
+{
+	struct lan966x_hwmon *hwmon = data;
+
+	regmap_update_bits(hwmon->regmap_pvt, PVT_SENSOR_CFG,
+			   SENSOR_CFG_SAMPLE_ENA | SENSOR_CFG_CONTINIOUS_MODE,
+			   0);
+}
+
+static int lan966x_hwmon_enable(struct device *dev,
+				struct lan966x_hwmon *hwmon)
+{
+	unsigned int mask = SENSOR_CFG_CLK_CFG |
+			    SENSOR_CFG_SAMPLE_ENA |
+			    SENSOR_CFG_START_CAPTURE |
+			    SENSOR_CFG_CONTINIOUS_MODE |
+			    SENSOR_CFG_PSAMPLE_ENA;
+	unsigned int val;
+	unsigned int div;
+	int ret;
+
+	/* enable continuous mode */
+	val = SENSOR_CFG_SAMPLE_ENA | SENSOR_CFG_CONTINIOUS_MODE;
+
+	/* set PVT clock to be between 1.15 and 1.25 MHz */
+	div = DIV_ROUND_CLOSEST(hwmon->clk_rate, LAN966X_PVT_CLK);
+	val |= FIELD_PREP(SENSOR_CFG_CLK_CFG, div);
+
+	ret = regmap_update_bits(hwmon->regmap_pvt, PVT_SENSOR_CFG,
+				 mask, val);
+	if (ret)
+		return ret;
+
+	return devm_add_action_or_reset(dev, lan966x_hwmon_disable, hwmon);
+}
+
+static struct regmap *lan966x_init_regmap(struct platform_device *pdev,
+					  const char *name)
+{
+	struct regmap_config regmap_config = {
+		.reg_bits = 32,
+		.reg_stride = 4,
+		.val_bits = 32,
+	};
+	void __iomem *base;
+
+	base = devm_platform_ioremap_resource_byname(pdev, name);
+	if (IS_ERR(base))
+		return ERR_CAST(base);
+
+	regmap_config.name = name;
+
+	return devm_regmap_init_mmio(&pdev->dev, base, &regmap_config);
+}
+
+static void lan966x_clk_disable(void *data)
+{
+	struct lan966x_hwmon *hwmon = data;
+
+	clk_disable_unprepare(hwmon->clk);
+}
+
+static int lan966x_clk_enable(struct device *dev, struct lan966x_hwmon *hwmon)
+{
+	int ret;
+
+	ret = clk_prepare_enable(hwmon->clk);
+	if (ret)
+		return ret;
+
+	return devm_add_action_or_reset(dev, lan966x_clk_disable, hwmon);
+}
+
+static int lan966x_hwmon_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct lan966x_hwmon *hwmon;
+	struct device *hwmon_dev;
+	int ret;
+
+	hwmon = devm_kzalloc(dev, sizeof(*hwmon), GFP_KERNEL);
+	if (!hwmon)
+		return -ENOMEM;
+
+	hwmon->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(hwmon->clk))
+		return dev_err_probe(dev, PTR_ERR(hwmon->clk),
+				     "failed to get clock\n");
+
+	ret = lan966x_clk_enable(dev, hwmon);
+	if (ret)
+		return dev_err_probe(dev, ret, "failed to enable clock\n");
+
+	hwmon->clk_rate = clk_get_rate(hwmon->clk);
+
+	hwmon->regmap_pvt = lan966x_init_regmap(pdev, "pvt");
+	if (IS_ERR(hwmon->regmap_pvt))
+		return dev_err_probe(dev, PTR_ERR(hwmon->regmap_pvt),
+				     "failed to get regmap for PVT registers\n");
+
+	hwmon->regmap_fan = lan966x_init_regmap(pdev, "fan");
+	if (IS_ERR(hwmon->regmap_fan))
+		return dev_err_probe(dev, PTR_ERR(hwmon->regmap_fan),
+				     "failed to get regmap for fan registers\n");
+
+	ret = lan966x_hwmon_enable(dev, hwmon);
+	if (ret)
+		return dev_err_probe(dev, ret, "failed to enable sensor\n");
+
+	hwmon_dev = devm_hwmon_device_register_with_info(&pdev->dev,
+				"lan966x_hwmon", hwmon,
+				&lan966x_hwmon_chip_info, NULL);
+	if (IS_ERR(hwmon_dev))
+		return dev_err_probe(dev, PTR_ERR(hwmon_dev),
+				     "failed to register hwmon device\n");
+
+	return 0;
+}
+
+static const struct of_device_id lan966x_hwmon_of_match[] = {
+	{ .compatible = "microchip,lan9668-hwmon" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, lan966x_hwmon_of_match);
+
+static struct platform_driver lan966x_hwmon_driver = {
+	.probe = lan966x_hwmon_probe,
+	.driver = {
+		.name = "lan966x-hwmon",
+		.of_match_table = lan966x_hwmon_of_match,
+	},
+};
+module_platform_driver(lan966x_hwmon_driver);
+
+MODULE_DESCRIPTION("LAN966x Hardware Monitoring Driver");
+MODULE_AUTHOR("Michael Walle <michael@walle.cc>");
+MODULE_LICENSE("GPL");