Merge tag 'pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "We have no core changes but lots of incremental development in drivers
  all over the place: Renesas, NXP, Mediatek and Actions Semiconductor
  keep churning out new SoCs.

  I have some subtree maintainers for Renesas and Intel helping out to
  keep down the load, it's been working smoothly (Samsung also have a
  subtree but it was not used this cycle.)

  New drivers:

   - NXP (ex Freescale) i.MX 8 QXP SoC driver.

   - Mediatek MT6797 SoC driver.

   - Mediatek MT7629 SoC driver.

   - Actions Semiconductor S700 SoC driver.

   - Renesas RZ/A2 SoC driver.

   - Allwinner sunxi suniv F1C100 SoC driver.

   - Qualcomm PMS405 PMIC driver.

   - Microsemi Ocelot Jaguar2 SoC driver.

  Improvements:

   - Some RT improvements (using raw spinlocks where appropriate).

   - A lot of new pin sets on the Renesas PFC pin controllers.

   - GPIO hogs now work on the Qualcomm SPMI/SSBI pin controller GPIO
     chips, and Xway.

   - Major modernization of the Intel pin control drivers.

   - STM32 pin control driver will now synchronize usage of pins with
     another CPU using a hardware spinlock"

* tag 'pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (145 commits)
  dt-bindings: arm: fsl-scu: add imx8qm pinctrl support
  pinctrl: freescale: Break dependency on SOC_IMX8MQ for i.MX8MQ
  pinctrl: imx-scu: Depend on IMX_SCU
  pinctrl: ocelot: Add dependency on HAS_IOMEM
  pinctrl: ocelot: add MSCC Jaguar2 support
  pinctrl: bcm: ns: support updated DT binding as syscon subnode
  dt-bindings: pinctrl: bcm4708-pinmux: rework binding to use syscon
  MAINTAINERS: merge at91 pinctrl entries
  pinctrl: imx8qxp: break the dependency on SOC_IMX8QXP
  pinctrl: uniphier: constify uniphier_pinctrl_socdata
  pinctrl: mediatek: improve Kconfig dependencies
  pinctrl: msm: mark PM functions as __maybe_unused
  dt-bindings: pinctrl: sunxi: Add supply properties
  pinctrl: meson: meson8b: add the missing GPIO_GROUPs for BOOT and CARD
  pinctrl: meson: meson8: add the missing GPIO_GROUPs for BOOT and CARD
  pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs"
  pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs"
  pinctrl: meson: meson8b: fix the GPIO function for the GPIOAO pins
  pinctrl: meson: meson8: fix the GPIO function for the GPIOAO pins
  pinctrl: sh-pfc: Make pinmux_cfg_reg.var_field_width[] variable-length
  ...

Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt

@@ -88,13 +88,16 @@ Pinctrl bindings based on SCU Message Protocol
 This binding uses the i.MX common pinctrl binding[3].
 
 Required properties:
-- compatible:		Should be "fsl,imx8qxp-iomuxc".
+- compatible:		Should be one of:
+			"fsl,imx8qm-iomuxc",
+			"fsl,imx8qxp-iomuxc".
 
 Required properties for Pinctrl sub nodes:
 - fsl,pins:		Each entry consists of 3 integers which represents
 			the mux and config setting for one pin. The first 2
 			integers <pin_id mux_mode> are specified using a
 			PIN_FUNC_ID macro, which can be found in
+			<dt-bindings/pinctrl/pads-imx8qm.h>,
 			<dt-bindings/pinctrl/pads-imx8qxp.h>.
 			The last integer CONFIG is the pad setting value like
 			pull-up on this pin.

Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt

+Actions Semi S700 Pin Controller
+
+This binding describes the pin controller found in the S700 SoC.
+
+Required Properties:
+
+- compatible:   Should be "actions,s700-pinctrl"
+- reg:          Should contain the register base address and size of
+		the pin controller.
+- clocks:       phandle of the clock feeding the pin controller
+- gpio-controller: Marks the device node as a GPIO controller.
+- gpio-ranges: Specifies the mapping between gpio controller and
+               pin-controller pins.
+- #gpio-cells: Should be two. The first cell is the gpio pin number
+		and the second cell is used for optional parameters.
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells: Specifies the number of cells needed to encode an
+		interrupt.  Shall be set to 2.  The first cell
+		defines the interrupt number, the second encodes
+		the trigger flags described in
+		bindings/interrupt-controller/interrupts.txt
+- interrupts: The interrupt outputs from the controller. There is one GPIO
+              interrupt per GPIO bank. The number of interrupts listed depends
+              on the number of GPIO banks on the SoC. The interrupts must be
+              ordered by bank, starting with bank 0.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+PIN CONFIGURATION NODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+Pinmux functions are available only for the pin groups while pinconf
+parameters are available for both pin groups and individual pins.
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+Required Properties:
+
+- pins:		An array of strings, each string containing the name of a pin.
+		These pins are used for selecting the pull control and schmitt
+		trigger parameters. The following are the list of pins
+		available:
+
+		eth_txd0, eth_txd1, eth_txd2, eth_txd3, eth_txen, eth_rxer,
+		eth_crs_dv, eth_rxd1, eth_rxd0, eth_rxd2, eth_rxd3, eth_ref_clk,
+		eth_mdc, eth_mdio, sirq0, sirq1, sirq2, i2s_d0, i2s_bclk0,
+		i2s_lrclk0, i2s_mclk0, i2s_d1, i2s_bclk1, i2s_lrclk1, i2s_mclk1,
+		pcm1_in, pcm1_clk, pcm1_sync, pcm1_out, ks_in0, ks_in1, ks_in2,
+		ks_in3, ks_out0, ks_out1, ks_out2, lvds_oep, lvds_oen, lvds_odp,
+		lvds_odn, lvds_ocp, lvds_ocn, lvds_obp, lvds_obn, lvds_oap,
+		lvds_oan, lvds_eep, lvds_een, lvds_edp, lvds_edn, lvds_ecp,
+		lvds_ecn, lvds_ebp, lvds_ebn, lvds_eap, lvds_ean, lcd0_d18,
+		lcd0_d2, dsi_dp3, dsi_dn3, dsi_dp1, dsi_dn1, dsi_cp, dsi_cn,
+		dsi_dp0, dsi_dn0, dsi_dp2, dsi_dn2, sd0_d0, sd0_d1, sd0_d2,
+		sd0_d3, sd1_d0, sd1_d1, sd1_d2, sd1_d3, sd0_cmd, sd0_clk,
+		sd1_cmd, sd1_clk, spi0_ss, spi0_miso, uart0_rx, uart0_tx,
+		uart2_rx, uart2_tx, uart2_rtsb, uart2_ctsb, uart3_rx, uart3_tx,
+		uart3_rtsb, uart3_ctsb, i2c0_sclk, i2c0_sdata, i2c1_sclk,
+		i2c1_sdata, i2c2_sdata, csi_dn0, csi_dp0, csi_dn1, csi_dp1,
+		csi_cn, csi_cp, csi_dn2, csi_dp2, csi_dn3, csi_dp3,
+		sensor0_pclk, sensor0_ckout, dnand_d0, dnand_d1, dnand_d2,
+		dnand_d3, dnand_d4, dnand_d5, dnand_d6, dnand_d7, dnand_wrb,
+		dnand_rdb, dnand_rdbn, dnand_dqs, dnand_dqsn, dnand_rb0,
+		dnand_ale, dnand_cle, dnand_ceb0, dnand_ceb1, dnand_ceb2,
+		dnand_ceb3, porb, clko_25m, bsel, pkg0, pkg1, pkg2, pkg3
+
+- groups:       An array of strings, each string containing the name of a pin
+                group. These pin groups are used for selecting the pinmux
+                functions.
+		rgmii_txd23_mfp, rgmii_rxd2_mfp, rgmii_rxd3_mfp, lcd0_d18_mfp,
+		rgmii_txd01_mfp, rgmii_txd0_mfp, rgmii_txd1_mfp, rgmii_txen_mfp,
+		rgmii_rxen_mfp, rgmii_rxd1_mfp, rgmii_rxd0_mfp, rgmii_ref_clk_mfp,
+		i2s_d0_mfp, i2s_pcm1_mfp, i2s0_pcm0_mfp, i2s1_pcm0_mfp,
+		i2s_d1_mfp, ks_in2_mfp, ks_in1_mfp, ks_in0_mfp, ks_in3_mfp,
+		ks_out0_mfp, ks_out1_mfp, ks_out2_mfp, lvds_o_pn_mfp, dsi_dn0_mfp,
+		dsi_dp2_mfp, lcd0_d2_mfp, dsi_dp3_mfp, dsi_dn3_mfp, dsi_dp0_mfp,
+		lvds_ee_pn_mfp, uart2_rx_tx_mfp, spi0_i2c_pcm_mfp, dsi_dnp1_cp_d2_mfp,
+		dsi_dnp1_cp_d17_mfp, lvds_e_pn_mfp, dsi_dn2_mfp, uart2_rtsb_mfp,
+		uart2_ctsb_mfp, uart3_rtsb_mfp, uart3_ctsb_mfp, sd0_d0_mfp, sd0_d1_mfp,
+		sd0_d2_d3_mfp, sd1_d0_d3_mfp, sd0_cmd_mfp, sd0_clk_mfp, sd1_cmd_mfp,
+		uart0_rx_mfp, clko_25m_mfp, csi_cn_cp_mfp, sens0_ckout_mfp, uart0_tx_mfp,
+		i2c0_mfp, csi_dn_dp_mfp, sen0_pclk_mfp, pcm1_in_mfp, pcm1_clk_mfp,
+		pcm1_sync_mfp, pcm1_out_mfp, dnand_data_wr_mfp, dnand_acle_ce0_mfp,
+		nand_ceb2_mfp, nand_ceb3_mfp
+
+		These pin groups are used for selecting the drive strength
+		parameters.
+
+		sirq_drv, rgmii_txd23_drv, rgmii_rxd23_drv, rgmii_txd01_txen_drv,
+		rgmii_rxer_drv, rgmii_crs_drv, rgmii_rxd10_drv, rgmii_ref_clk_drv,
+		smi_mdc_mdio_drv, i2s_d0_drv, i2s_bclk0_drv, i2s3_drv, i2s13_drv,
+		pcm1_drv, ks_in_drv, ks_out_drv, lvds_all_drv, lcd_d18_d2_drv,
+		dsi_all_drv, sd0_d0_d3_drv, sd0_cmd_drv, sd0_clk_drv, spi0_all_drv,
+		uart0_rx_drv, uart0_tx_drv, uart2_all_drv, i2c0_all_drv, i2c12_all_drv,
+		sens0_pclk_drv, sens0_ckout_drv, uart3_all_drv
+
+- function:	An array of strings, each string containing the name of the
+		pinmux functions. These functions can only be selected by
+		the corresponding pin groups. The following are the list of
+		pinmux functions available:
+
+		nor, eth_rgmii, eth_sgmii, spi0, spi1, spi2, spi3, seNs0, sens1,
+		uart0, uart1, uart2, uart3, uart4, uart5, uart6, i2s0, i2s1,
+		pcm1, pcm0, ks, jtag, pwm0, pwm1, pwm2, pwm3, pwm4, pwm5, p0,
+		sd0, sd1, sd2, i2c0, i2c1, i2c2, i2c3, dsi, lvds, usb30,
+		clko_25m, mipi_csi, nand, spdif, sirq0, sirq1, sirq2, bt, lcd0
+
+Optional Properties:
+
+- bias-pull-down: No arguments. The specified pins should be configured as
+		pull down.
+- bias-pull-up:   No arguments. The specified pins should be configured as
+		pull up.
+- input-schmitt-enable: No arguments: Enable schmitt trigger for the specified
+		pins
+- input-schmitt-disable: No arguments: Disable schmitt trigger for the specified
+		pins
+- drive-strength: Integer. Selects the drive strength for the specified
+		pins in mA.
+		Valid values are:
+		<2>
+		<4>
+		<8>
+		<12>
+
+Example:
+
+	pinctrl: pinctrl@e01b0000 {
+		compatible = "actions,s700-pinctrl";
+		reg = <0x0 0xe01b0000 0x0 0x1000>;
+		clocks = <&cmu CLK_GPIO>;
+		gpio-controller;
+		gpio-ranges = <&pinctrl 0 0 136>;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+                interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
+                             <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,
+                             <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>,
+                             <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+                             <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+
+		uart3-default: uart3-default {
+			pinmux {
+				groups = "uart3_rtsb_mfp", "uart3_ctsb_mfp";
+				function = "uart3";
+			};
+			pinconf {
+				groups = "uart3_all_drv";
+				drive-strength = <2>;
+			};
+		};
+	};

Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt

@@ -29,6 +29,7 @@ Required properties:
   "allwinner,sun50i-h5-pinctrl"
   "allwinner,sun50i-h6-pinctrl"
   "allwinner,sun50i-h6-r-pinctrl"
+  "allwinner,suniv-f1c100s-pinctrl"
   "nextthing,gr8-pinctrl"
 
 - reg: Should contain the register physical address and length for the
@@ -43,6 +44,19 @@ Note: For backward compatibility reasons, the hosc and losc clocks are only
 required if you need to use the optional input-debounce property. Any new
 device tree should set them.
 
+Each pin bank, depending on the SoC, can have an associated regulator:
+
+- vcc-pa-supply: for the A10, A20, A31, A31s, A80 and R40 SoCs
+- vcc-pb-supply: for the A31, A31s, A80 and V3s SoCs
+- vcc-pc-supply: for the A10, A20, A31, A31s, A64, A80, H5, R40 and V3s SoCs
+- vcc-pd-supply: for the A23, A31, A31s, A64, A80, A83t, H3, H5 and R40 SoCs
+- vcc-pe-supply: for the A10, A20, A31, A31s, A64, A80, R40 and V3s SoCs
+- vcc-pf-supply: for the A10, A20, A31, A31s, A80, R40 and V3s SoCs
+- vcc-pg-supply: for the A10, A20, A31, A31s, A64, A80, H3, H5, R40 and V3s SoCs
+- vcc-ph-supply: for the A31, A31s and A80 SoCs
+- vcc-pl-supply: for the r-pinctrl of the A64, A80 and A83t SoCs
+- vcc-pm-supply: for the r-pinctrl of the A31, A31s and A80 SoCs
+
 Optional properties:
   - input-debounce: Array of debouncing periods in microseconds. One period per
     irq bank found in the controller. 0 if no setup required.

Documentation/devicetree/bindings/pinctrl/brcm,bcm4708-pinmux.txt

@@ -7,13 +7,15 @@ configure controller correctly.
 
 A list of pins varies across chipsets so few bindings are available.
 
+Node of the pinmux must be nested in the CRU (Central Resource Unit) "syscon"
+noce.
+
 Required properties:
 - compatible: must be one of:
 	"brcm,bcm4708-pinmux"
 	"brcm,bcm4709-pinmux"
 	"brcm,bcm53012-pinmux"
-- reg: iomem address range of CRU (Central Resource Unit) pin registers
-- reg-names: "cru_gpio_control" - the only needed & supported reg right now
+- offset: offset of pin registers in the CRU block
 
 Functions and their groups available for all chipsets:
 - "spi": "spi_grp"
@@ -37,16 +39,12 @@ Example:
 		#size-cells = <1>;
 
 		cru@100 {
-			compatible = "simple-bus";
+			compatible = "syscon", "simple-mfd";
 			reg = <0x100 0x1a4>;
-			ranges;
-			#address-cells = <1>;
-			#size-cells = <1>;
 
-			pin-controller@1c0 {
+			pinctrl {
 				compatible = "brcm,bcm4708-pinmux";
-				reg = <0x1c0 0x24>;
-				reg-names = "cru_gpio_control";
+				offset = <0xc0>;
 
 				spi-pins {
 					function = "spi";

Documentation/devicetree/bindings/pinctrl/fsl,imx7ulp-pinctrl.txt

@@ -7,55 +7,47 @@ Note:
 This binding doc is only for the IOMUXC1 support in A7 Domain and it only
 supports generic pin config.
 
-Please also refer pinctrl-bindings.txt in this directory for generic pinctrl
-binding.
-
-=== Pin Controller Node ===
+Please refer to fsl,imx-pinctrl.txt in this directory for common binding
+part and usage.
 
 Required properties:
-- compatible:	"fsl,imx7ulp-iomuxc1"
-- reg:		Should contain the base physical address and size of the iomuxc
-		registers.
-
-=== Pin Configuration Node ===
-- pinmux: One integers array, represents a group of pins mux setting.
-	The format is pinmux = <PIN_FUNC_ID>, PIN_FUNC_ID is a pin working on
-	a specific function.
-
-	NOTE: i.MX7ULP PIN_FUNC_ID consists of 4 integers as it shares one mux
-	and config register as follows:
-	<mux_conf_reg input_reg mux_mode input_val>
-
-	Refer to imx7ulp-pinfunc.h in in device tree source folder for all
-	available imx7ulp PIN_FUNC_ID.
-
-Optional Properties:
-- drive-strength		Integer. Controls Drive Strength
-					0: Standard
-					1: Hi Driver
-- drive-push-pull		Bool. Enable Pin Push-pull
-- drive-open-drain		Bool. Enable Pin Open-drian
-- slew-rate:			Integer. Controls Slew Rate
-					0: Standard
-					1: Slow
-- bias-disable:			Bool. Pull disabled
-- bias-pull-down:		Bool. Pull down on pin
-- bias-pull-up:			Bool. Pull up on pin
+- compatible:	"fsl,imx7ulp-iomuxc1".
+- fsl,pins:	Each entry consists of 5 integers which represents the mux
+		and config setting for one pin. The first 4 integers
+		<mux_conf_reg input_reg mux_mode input_val> are specified
+		using a PIN_FUNC_ID macro, which can be found in
+		imx7ulp-pinfunc.h in the device tree source folder.
+		The last integer CONFIG is the pad setting value like
+		pull-up on this pin.
+
+		Please refer to i.MX7ULP Reference Manual for detailed
+		CONFIG settings.
+
+CONFIG bits definition:
+PAD_CTL_OBE		(1 << 17)
+PAD_CTL_IBE		(1 << 16)
+PAD_CTL_LK		(1 << 16)
+PAD_CTL_DSE_HI		(1 << 6)
+PAD_CTL_DSE_STD		(0 << 6)
+PAD_CTL_ODE		(1 << 5)
+PAD_CTL_PUSH_PULL	(0 << 5)
+PAD_CTL_SRE_SLOW	(1 << 2)
+PAD_CTL_SRE_STD		(0 << 2)
+PAD_CTL_PE		(1 << 0)
 
 Examples:
 #include "imx7ulp-pinfunc.h"
 
 /* Pin Controller Node */
-iomuxc1: iomuxc@40ac0000 {
+iomuxc1: pinctrl@40ac0000 {
 	compatible = "fsl,imx7ulp-iomuxc1";
 	reg = <0x40ac0000 0x1000>;
 
 	/* Pin Configuration Node */
 	pinctrl_lpuart4: lpuart4grp {
-		pinmux = <
-			IMX7ULP_PAD_PTC3__LPUART4_RX
-			IMX7ULP_PAD_PTC2__LPUART4_TX
+		fsl,pins = <
+			IMX7ULP_PAD_PTC3__LPUART4_RX	0x1
+			IMX7ULP_PAD_PTC2__LPUART4_TX	0x1
 		>;
-		bias-pull-up;
 	};
 };

Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.txt

@@ -2,7 +2,8 @@ Microsemi Ocelot pin controller Device Tree Bindings
 ----------------------------------------------------
 
 Required properties:
- - compatible		: Should be "mscc,ocelot-pinctrl"
+ - compatible		: Should be "mscc,ocelot-pinctrl" or
+				"mscc,jaguar2-pinctrl"
  - reg			: Address and length of the register set for the device
  - gpio-controller	: Indicates this device is a GPIO controller
  - #gpio-cells		: Must be 2.

Documentation/devicetree/bindings/pinctrl/pinctrl-mt6797.txt

+* MediaTek MT6797 Pin Controller
+
+The MediaTek's MT6797 Pin controller is used to control SoC pins.
+
+Required properties:
+- compatible: Value should be one of the following.
+              "mediatek,mt6797-pinctrl", compatible with mt6797 pinctrl.
+- reg:        Should contain address and size for gpio, iocfgl, iocfgb,
+              iocfgr and iocfgt register bases.
+- reg-names:  An array of strings describing the "reg" entries. Must
+              contain "gpio", "iocfgl", "iocfgb", "iocfgr", "iocfgt".
+- gpio-controller: Marks the device node as a gpio controller.
+- #gpio-cells: Should be two. The first cell is the gpio pin number
+               and the second cell is used for optional parameters.
+
+Optional properties:
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells: Should be two.
+- interrupts : The interrupt outputs from the controller.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices.
+
+Subnode format
+A pinctrl node should contain at least one subnodes representing the
+pinctrl groups available on the machine. Each subnode will list the
+pins it needs, and how they should be configured, with regard to muxer
+configuration, pullups, drive strength, input enable/disable and input schmitt.
+
+    node {
+        pinmux = <PIN_NUMBER_PINMUX>;
+        GENERIC_PINCONFIG;
+    };
+
+Required properties:
+- pinmux: Integer array, represents gpio pin number and mux setting.
+    Supported pin number and mux varies for different SoCs, and are defined
+    as macros in dt-bindings/pinctrl/<soc>-pinfunc.h directly.
+
+Optional properties:
+- GENERIC_PINCONFIG: is the generic pinconfig options to use, bias-disable,
+    bias-pull, bias-pull-down, input-enable, input-schmitt-enable,
+    input-schmitt-disable, output-enable output-low, output-high,
+    drive-strength, and slew-rate are valid.
+
+    Valid arguments for 'slew-rate' are '0' for no slew rate controlled and
+    '1' for slower slew rate respectively. Valid arguments for 'drive-strength'
+    is limited, such as 2, 4, 8, 12, or 16 in mA.
+
+    Some optional vendor properties as defined are valid to specify in a
+    pinconf subnode:
+    - mediatek,tdsel: An integer describing the steps for output level shifter
+      duty cycle when asserted (high pulse width adjustment). Valid arguments
+      are from 0 to 15.
+    - mediatek,rdsel: An integer describing the steps for input level shifter
+      duty cycle when asserted (high pulse width adjustment). Valid arguments
+      are from 0 to 63.
+    - mediatek,pull-up-adv: An integer describing the code R1R0 as 0, 1, 2
+      or 3 for the advanced pull-up resistors.
+    - mediatek,pull-down-adv: An integer describing the code R1R0 as 0, 1, 2,
+      or 3 for the advanced pull-down resistors.
+
+Examples:
+
+        pio: pinctrl@10005000 {
+                compatible = "mediatek,mt6797-pinctrl";
+                reg = <0 0x10005000 0 0x1000>,
+                      <0 0x10002000 0 0x400>,
+                      <0 0x10002400 0 0x400>,
+                      <0 0x10002800 0 0x400>,
+                      <0 0x10002C00 0 0x400>;
+                reg-names = "gpio", "iocfgl", "iocfgb",
+                            "iocfgr", "iocfgt";
+                gpio-controller;
+                #gpio-cells = <2>;
+
+                uart1_pins_a: uart1 {
+                        pins1 {
+                                pinmux = <MT6797_GPIO232__FUNC_URXD1>,
+                                         <MT6797_GPIO233__FUNC_UTXD1>;
+                        };
+                };
+        };

Documentation/devicetree/bindings/pinctrl/pinctrl-mt7622.txt

@@ -3,6 +3,7 @@
 Required properties for the root node:
  - compatible: Should be one of the following
 	       "mediatek,mt7622-pinctrl" for MT7622 SoC
+	       "mediatek,mt7629-pinctrl" for MT7629 SoC
  - reg: offset and length of the pinctrl space
 
  - gpio-controller: Marks the device node as a GPIO controller.
@@ -324,6 +325,136 @@ group.
 	"uart4_2_rts_cts"		"uart"		95, 96
 	"watchdog"			"watchdog"	78
 
+
+== Valid values for pins, function and groups on MT7629 ==
+
+	Pin #:  Valid values for pins
+	-----------------------------
+	PIN 0: "TOP_5G_CLK"
+	PIN 1: "TOP_5G_DATA"
+	PIN 2: "WF0_5G_HB0"
+	PIN 3: "WF0_5G_HB1"
+	PIN 4: "WF0_5G_HB2"
+	PIN 5: "WF0_5G_HB3"
+	PIN 6: "WF0_5G_HB4"
+	PIN 7: "WF0_5G_HB5"
+	PIN 8: "WF0_5G_HB6"
+	PIN 9: "XO_REQ"
+	PIN 10: "TOP_RST_N"
+	PIN 11: "SYS_WATCHDOG"
+	PIN 12: "EPHY_LED0_N_JTDO"
+	PIN 13: "EPHY_LED1_N_JTDI"
+	PIN 14: "EPHY_LED2_N_JTMS"
+	PIN 15: "EPHY_LED3_N_JTCLK"
+	PIN 16: "EPHY_LED4_N_JTRST_N"
+	PIN 17: "WF2G_LED_N"
+	PIN 18: "WF5G_LED_N"
+	PIN 19: "I2C_SDA"
+	PIN 20: "I2C_SCL"
+	PIN 21: "GPIO_9"
+	PIN 22: "GPIO_10"
+	PIN 23: "GPIO_11"
+	PIN 24: "GPIO_12"
+	PIN 25: "UART1_TXD"
+	PIN 26: "UART1_RXD"
+	PIN 27: "UART1_CTS"
+	PIN 28: "UART1_RTS"
+	PIN 29: "UART2_TXD"
+	PIN 30: "UART2_RXD"
+	PIN 31: "UART2_CTS"
+	PIN 32: "UART2_RTS"
+	PIN 33: "MDI_TP_P1"
+	PIN 34: "MDI_TN_P1"
+	PIN 35: "MDI_RP_P1"
+	PIN 36: "MDI_RN_P1"
+	PIN 37: "MDI_RP_P2"
+	PIN 38: "MDI_RN_P2"
+	PIN 39: "MDI_TP_P2"
+	PIN 40: "MDI_TN_P2"
+	PIN 41: "MDI_TP_P3"
+	PIN 42: "MDI_TN_P3"
+	PIN 43: "MDI_RP_P3"
+	PIN 44: "MDI_RN_P3"
+	PIN 45: "MDI_RP_P4"
+	PIN 46: "MDI_RN_P4"
+	PIN 47: "MDI_TP_P4"
+	PIN 48: "MDI_TN_P4"
+	PIN 49: "SMI_MDC"
+	PIN 50: "SMI_MDIO"
+	PIN 51: "PCIE_PERESET_N"
+	PIN 52: "PWM_0"
+	PIN 53: "GPIO_0"
+	PIN 54: "GPIO_1"
+	PIN 55: "GPIO_2"
+	PIN 56: "GPIO_3"
+	PIN 57: "GPIO_4"
+	PIN 58: "GPIO_5"
+	PIN 59: "GPIO_6"
+	PIN 60: "GPIO_7"
+	PIN 61: "GPIO_8"
+	PIN 62: "SPI_CLK"
+	PIN 63: "SPI_CS"
+	PIN 64: "SPI_MOSI"
+	PIN 65: "SPI_MISO"
+	PIN 66: "SPI_WP"
+	PIN 67: "SPI_HOLD"
+	PIN 68: "UART0_TXD"
+	PIN 69: "UART0_RXD"
+	PIN 70: "TOP_2G_CLK"
+	PIN 71: "TOP_2G_DATA"
+	PIN 72: "WF0_2G_HB0"
+	PIN 73: "WF0_2G_HB1"
+	PIN 74: "WF0_2G_HB2"
+	PIN 75: "WF0_2G_HB3"
+	PIN 76: "WF0_2G_HB4"
+	PIN 77: "WF0_2G_HB5"
+	PIN 78: "WF0_2G_HB6"
+
+Valid values for function are:
+	"eth", "i2c", "led", "flash", "pcie", "pwm", "spi", "uart",
+	"watchdog", "wifi"
+
+Valid values for groups are:
+	Valid value			function	pins (in pin#)
+	----------------------------------------------------------------
+	"mdc_mdio"			"eth"		23, 24
+	"i2c_0"				"i2c"		19, 20
+	"i2c_1"				"i2c"		53, 54
+	"ephy_leds"			"led"		12, 13, 14, 15, 16,
+							17, 18
+	"ephy0_led"			"led"		12
+	"ephy1_led"			"led"		13
+	"ephy2_led"			"led"		14
+	"ephy3_led"			"led"		15
+	"ephy4_led"			"led"		16
+	"wf2g_led"			"led"		17
+	"wf5g_led"			"led"		18
+	"snfi"				"flash"		62, 63, 64, 65, 66, 67
+	"spi_nor"			"flash"		62, 63, 64, 65, 66, 67
+	"pcie_pereset"			"pcie"		51
+	"pcie_wake"			"pcie"		55
+	"pcie_clkreq"			"pcie"		56
+	"pwm_0"				"pwm"		52
+	"pwm_1"				"pwm"		61
+	"spi_0"				"spi"		21, 22, 23, 24
+	"spi_1"				"spi"		62, 63, 64, 65
+	"spi_wp"			"spi"		66
+	"spi_hold"			"spi"		67
+	"uart0_txd_rxd"			"uart"		68, 69
+	"uart1_0_txd_rxd"		"uart"		25, 26
+	"uart1_0_cts_rts"		"uart"		27, 28
+	"uart1_1_txd_rxd"		"uart"		53, 54
+	"uart1_1_cts_rts"		"uart"		55, 56
+	"uart2_0_txd_rxd"		"uart"		29, 30
+	"uart2_0_cts_rts"		"uart"		31, 32
+	"uart2_1_txd_rxd"		"uart"		57, 58
+	"uart2_1_cts_rts"		"uart"		59, 60
+	"watchdog"			"watchdog"	11
+	"wf0_2g"			"wifi"		70, 71, 72, 73, 74,
+							75, 76, 77, 78
+	"wf0_5g"			"wifi"		0, 1, 2, 3, 4, 5, 6,
+							7, 8, 9, 10
+
 Example:
 
 	pio: pinctrl@10211000 {

Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt

@@ -92,7 +92,7 @@ to specify in a pin configuration subnode:
 		    gpio1-gpio26 for pm8998
 		    gpio1-gpio22 for pma8084
 		    gpio1-gpio10 for pmi8994
-		    gpio1-gpio11 for pms405
+		    gpio1-gpio12 for pms405 (holes on gpio1, gpio9 and gpio10)
 
 - function:
 	Usage: required

Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.txt

+Renesas RZ/A2 combined Pin and GPIO controller
+
+The Renesas SoCs of the RZ/A2 series feature a combined Pin and GPIO controller.
+Pin multiplexing and GPIO configuration is performed on a per-pin basis.
+Each port features up to 8 pins, each of them configurable for GPIO
+function (port mode) or in alternate function mode.
+Up to 8 different alternate function modes exist for each single pin.
+
+Pin controller node
+-------------------
+
+Required properties:
+  - compatible: shall be:
+    - "renesas,r7s9210-pinctrl": for RZ/A2M
+  - reg
+    Address base and length of the memory area where the pin controller
+    hardware is mapped to.
+  - gpio-controller
+    This pin controller also controls pins as GPIO
+  - #gpio-cells
+    Must be 2
+  - gpio-ranges
+    Expresses the total number of GPIO ports/pins in this SoC
+
+Example: Pin controller node for RZ/A2M SoC (r7s9210)
+
+	pinctrl: pin-controller@fcffe000 {
+		compatible = "renesas,r7s9210-pinctrl";
+		reg = <0xfcffe000 0x1000>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-ranges = <&pinctrl 0 0 176>;
+	};
+
+Sub-nodes
+---------
+
+The child nodes of the pin controller designate pins to be used for
+specific peripheral functions or as GPIO.
+
+- Pin multiplexing sub-nodes:
+  A pin multiplexing sub-node describes how to configure a set of
+  (or a single) pin in some desired alternate function mode.
+  The values for the pinmux properties are a combination of port name, pin
+  number and the desired function index. Use the RZA2_PINMUX macro located
+  in include/dt-bindings/pinctrl/r7s9210-pinctrl.h to easily define these.
+  For assigning GPIO pins, use the macro RZA2_PIN also in r7s9210-pinctrl.h
+  to express the desired port pin.
+
+  Required properties:
+    - pinmux:
+      integer array representing pin number and pin multiplexing configuration.
+      When a pin has to be configured in alternate function mode, use this
+      property to identify the pin by its global index, and provide its
+      alternate function configuration number along with it.
+      When multiple pins are required to be configured as part of the same
+      alternate function they shall be specified as members of the same
+      argument list of a single "pinmux" property.
+      Helper macros to ease assembling the pin index from its position
+      (port where it sits on and pin number) and alternate function identifier
+      are provided by the pin controller header file at:
+      <dt-bindings/pinctrl/r7s9210-pinctrl.h>
+      Integers values in "pinmux" argument list are assembled as:
+      ((PORT * 8 + PIN) | MUX_FUNC << 16)
+
+  Example: Board specific pins configuration
+
+	&pinctrl {
+		/* Serial Console */
+		scif4_pins: serial4 {
+			pinmux = <RZA2_PINMUX(PORT9, 0, 4)>,	/* TxD4 */
+				 <RZA2_PINMUX(PORT9, 1, 4)>;	/* RxD4 */
+		};
+	};
+
+  Example: Assigning a GPIO:
+
+	leds {
+		status = "okay";
+		compatible = "gpio-leds";
+
+		led0 {
+			/* P6_0 */
+			gpios = <&pinctrl RZA2_PIN(PORT6, 0) GPIO_ACTIVE_HIGH>;
+		};
+	};

Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt

@@ -56,6 +56,7 @@ Optional properties:
    More details in Documentation/devicetree/bindings/gpio/gpio.txt.
  - st,bank-ioport: should correspond to the EXTI IOport selection (EXTI line
    used to select GPIOs as interrupts).
+ - hwlocks: reference to a phandle of a hardware spinlock provider node.
 
 Example 1:
 #include <dt-bindings/pinctrl/stm32f429-pinfunc.h>

MAINTAINERS

@@ -11919,18 +11919,12 @@ F:	Documentation/driver-api/pinctl.rst
 F:	drivers/pinctrl/
 F:	include/linux/pinctrl/
 
-PIN CONTROLLER - ATMEL AT91
-M:	Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
-L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Maintained
-F:	drivers/pinctrl/pinctrl-at91.*
-
-PIN CONTROLLER - ATMEL AT91 PIO4
+PIN CONTROLLER - MICROCHIP AT91
 M:	Ludovic Desroches <ludovic.desroches@microchip.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 L:	linux-gpio@vger.kernel.org
 S:	Supported
-F:	drivers/pinctrl/pinctrl-at91-pio4.*
+F:	drivers/pinctrl/pinctrl-at91*
 
 PIN CONTROLLER - FREESCALE
 M:	Dong Aisheng <aisheng.dong@nxp.com>
@@ -11966,11 +11960,11 @@ F:	Documentation/devicetree/bindings/pinctrl/qcom,*.txt
 F:	drivers/pinctrl/qcom/
 
 PIN CONTROLLER - RENESAS
-M:	Laurent Pinchart <laurent.pinchart@ideasonboard.com>
 M:	Geert Uytterhoeven <geert+renesas@glider.be>
 L:	linux-renesas-soc@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers.git sh-pfc
 S:	Maintained
+F:	drivers/pinctrl/pinctrl-rz*
 F:	drivers/pinctrl/sh-pfc/
 
 PIN CONTROLLER - SAMSUNG

drivers/pinctrl/Kconfig

@@ -195,6 +195,17 @@ config PINCTRL_RZA1
 	help
 	  This selects pinctrl driver for Renesas RZ/A1 platforms.
 
+config PINCTRL_RZA2
+	bool "Renesas RZ/A2 gpio and pinctrl driver"
+	depends on OF
+	depends on ARCH_R7S9210 || COMPILE_TEST
+	select GPIOLIB
+	select GENERIC_PINCTRL_GROUPS
+	select GENERIC_PINMUX_FUNCTIONS
+	select GENERIC_PINCONF
+	help
+	  This selects GPIO and pinctrl driver for Renesas RZ/A2 platforms.
+
 config PINCTRL_RZN1
 	bool "Renesas RZ/N1 pinctrl driver"
 	depends on OF
@@ -339,15 +350,15 @@ config PINCTRL_RK805
 	  This selects the pinctrl driver for RK805.
 
 config PINCTRL_OCELOT
-	bool "Pinctrl driver for the Microsemi Ocelot SoCs"
-	default y
+	bool "Pinctrl driver for the Microsemi Ocelot and Jaguar2 SoCs"
 	depends on OF
-	depends on MSCC_OCELOT || COMPILE_TEST
+	depends on HAS_IOMEM
 	select GPIOLIB
 	select GPIOLIB_IRQCHIP
 	select GENERIC_PINCONF
 	select GENERIC_PINCTRL_GROUPS
 	select GENERIC_PINMUX_FUNCTIONS
+	select OF_GPIO
 	select REGMAP_MMIO
 
 source "drivers/pinctrl/actions/Kconfig"

drivers/pinctrl/Makefile

@@ -27,6 +27,7 @@ obj-$(CONFIG_PINCTRL_PIC32)	+= pinctrl-pic32.o
 obj-$(CONFIG_PINCTRL_PISTACHIO)	+= pinctrl-pistachio.o
 obj-$(CONFIG_PINCTRL_ROCKCHIP)	+= pinctrl-rockchip.o
 obj-$(CONFIG_PINCTRL_RZA1)	+= pinctrl-rza1.o
+obj-$(CONFIG_PINCTRL_RZA2)	+= pinctrl-rza2.o
 obj-$(CONFIG_PINCTRL_RZN1)	+= pinctrl-rzn1.o
 obj-$(CONFIG_PINCTRL_SINGLE)	+= pinctrl-single.o
 obj-$(CONFIG_PINCTRL_SIRF)	+= sirf/

drivers/pinctrl/actions/Kconfig

@@ -9,6 +9,12 @@ config PINCTRL_OWL
 	help
 	  Say Y here to enable Actions Semi OWL pinctrl driver
 
+config PINCTRL_S700
+	bool "Actions Semi S700 pinctrl driver"
+	depends on PINCTRL_OWL
+	help
+	  Say Y here to enable Actions Semi S700 pinctrl driver
+
 config PINCTRL_S900
 	bool "Actions Semi S900 pinctrl driver"
 	depends on PINCTRL_OWL

drivers/pinctrl/actions/Makefile

 obj-$(CONFIG_PINCTRL_OWL)	+= pinctrl-owl.o
+obj-$(CONFIG_PINCTRL_S700) 	+= pinctrl-s700.o
 obj-$(CONFIG_PINCTRL_S900) 	+= pinctrl-s900.o

drivers/pinctrl/actions/pinctrl-owl.c

@@ -246,60 +246,6 @@ static int owl_pad_pinconf_reg(const struct owl_padinfo *info,
 	return 0;
 }
 
-static int owl_pad_pinconf_arg2val(const struct owl_padinfo *info,
-				unsigned int param,
-				u32 *arg)
-{
-	switch (param) {
-	case PIN_CONFIG_BIAS_BUS_HOLD:
-		*arg = OWL_PINCONF_PULL_HOLD;
-		break;
-	case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
-		*arg = OWL_PINCONF_PULL_HIZ;
-		break;
-	case PIN_CONFIG_BIAS_PULL_DOWN:
-		*arg = OWL_PINCONF_PULL_DOWN;
-		break;
-	case PIN_CONFIG_BIAS_PULL_UP:
-		*arg = OWL_PINCONF_PULL_UP;
-		break;
-	case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
-		*arg = (*arg >= 1 ? 1 : 0);
-		break;
-	default:
-		return -ENOTSUPP;
-	}
-
-	return 0;
-}
-
-static int owl_pad_pinconf_val2arg(const struct owl_padinfo *padinfo,
-				unsigned int param,
-				u32 *arg)
-{
-	switch (param) {
-	case PIN_CONFIG_BIAS_BUS_HOLD:
-		*arg = *arg == OWL_PINCONF_PULL_HOLD;
-		break;
-	case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
-		*arg = *arg == OWL_PINCONF_PULL_HIZ;
-		break;
-	case PIN_CONFIG_BIAS_PULL_DOWN:
-		*arg = *arg == OWL_PINCONF_PULL_DOWN;
-		break;
-	case PIN_CONFIG_BIAS_PULL_UP:
-		*arg = *arg == OWL_PINCONF_PULL_UP;
-		break;
-	case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
-		*arg = *arg == 1;
-		break;
-	default:
-		return -ENOTSUPP;
-	}
-
-	return 0;
-}
-
 static int owl_pin_config_get(struct pinctrl_dev *pctrldev,
 				unsigned int pin,
 				unsigned long *config)
@@ -318,7 +264,10 @@ static int owl_pin_config_get(struct pinctrl_dev *pctrldev,
 
 	arg = owl_read_field(pctrl, reg, bit, width);
 
-	ret = owl_pad_pinconf_val2arg(info, param, &arg);
+	if (!pctrl->soc->padctl_val2arg)
+		return -ENOTSUPP;
+
+	ret = pctrl->soc->padctl_val2arg(info, param, &arg);
 	if (ret)
 		return ret;
 
@@ -349,7 +298,10 @@ static int owl_pin_config_set(struct pinctrl_dev *pctrldev,
 		if (ret)
 			return ret;
 
-		ret = owl_pad_pinconf_arg2val(info, param, &arg);
+		if (!pctrl->soc->padctl_arg2val)
+			return -ENOTSUPP;
+
+		ret = pctrl->soc->padctl_arg2val(info, param, &arg);
 		if (ret)
 			return ret;
 
@@ -787,7 +739,7 @@ static void owl_gpio_irq_mask(struct irq_data *data)
 	val = readl_relaxed(gpio_base + port->intc_msk);
 	if (val == 0)
 		owl_gpio_update_reg(gpio_base + port->intc_ctl,
-					OWL_GPIO_CTLR_ENABLE, false);
+					OWL_GPIO_CTLR_ENABLE + port->shared_ctl_offset * 5, false);
 
 	raw_spin_unlock_irqrestore(&pctrl->lock, flags);
 }
@@ -811,7 +763,8 @@ static void owl_gpio_irq_unmask(struct irq_data *data)
 
 	/* enable port interrupt */
 	value = readl_relaxed(gpio_base + port->intc_ctl);
-	value |= BIT(OWL_GPIO_CTLR_ENABLE) | BIT(OWL_GPIO_CTLR_SAMPLE_CLK_24M);
+	value |= ((BIT(OWL_GPIO_CTLR_ENABLE) | BIT(OWL_GPIO_CTLR_SAMPLE_CLK_24M))
+			<< port->shared_ctl_offset * 5);
 	writel_relaxed(value, gpio_base + port->intc_ctl);
 
 	/* enable GPIO interrupt */
@@ -849,7 +802,7 @@ static void owl_gpio_irq_ack(struct irq_data *data)
 	raw_spin_lock_irqsave(&pctrl->lock, flags);
 
 	owl_gpio_update_reg(gpio_base + port->intc_ctl,
-				OWL_GPIO_CTLR_PENDING, true);
+				OWL_GPIO_CTLR_PENDING + port->shared_ctl_offset * 5, true);
 
 	raw_spin_unlock_irqrestore(&pctrl->lock, flags);
 }

drivers/pinctrl/actions/pinctrl-owl.h

@@ -15,12 +15,135 @@
 #define OWL_PINCONF_SLEW_SLOW 0
 #define OWL_PINCONF_SLEW_FAST 1
 
-enum owl_pinconf_pull {
-	OWL_PINCONF_PULL_HIZ,
-	OWL_PINCONF_PULL_DOWN,
-	OWL_PINCONF_PULL_UP,
-	OWL_PINCONF_PULL_HOLD,
-};
+#define MUX_PG(group_name, reg, shift, width)				\
+	{								\
+		.name = #group_name,					\
+		.pads = group_name##_pads,				\
+		.npads = ARRAY_SIZE(group_name##_pads),			\
+		.funcs = group_name##_funcs,				\
+		.nfuncs = ARRAY_SIZE(group_name##_funcs),		\
+		.mfpctl_reg  = MFCTL##reg,				\
+		.mfpctl_shift = shift,					\
+		.mfpctl_width = width,					\
+		.drv_reg = -1,						\
+		.drv_shift = -1,					\
+		.drv_width = -1,					\
+		.sr_reg = -1,						\
+		.sr_shift = -1,						\
+		.sr_width = -1,						\
+	}
+
+#define DRV_PG(group_name, reg, shift, width)				\
+	{								\
+		.name = #group_name,					\
+		.pads = group_name##_pads,				\
+		.npads = ARRAY_SIZE(group_name##_pads),			\
+		.mfpctl_reg  = -1,					\
+		.mfpctl_shift = -1,					\
+		.mfpctl_width = -1,					\
+		.drv_reg = PAD_DRV##reg,				\
+		.drv_shift = shift,					\
+		.drv_width = width,					\
+		.sr_reg = -1,						\
+		.sr_shift = -1,						\
+		.sr_width = -1,						\
+	}
+
+#define SR_PG(group_name, reg, shift, width)				\
+	{								\
+		.name = #group_name,					\
+		.pads = group_name##_pads,				\
+		.npads = ARRAY_SIZE(group_name##_pads),			\
+		.mfpctl_reg  = -1,					\
+		.mfpctl_shift = -1,					\
+		.mfpctl_width = -1,					\
+		.drv_reg = -1,						\
+		.drv_shift = -1,					\
+		.drv_width = -1,					\
+		.sr_reg = PAD_SR##reg,					\
+		.sr_shift = shift,					\
+		.sr_width = width,					\
+	}
+
+#define FUNCTION(fname)					\
+	{						\
+		.name = #fname,				\
+		.groups = fname##_groups,		\
+		.ngroups = ARRAY_SIZE(fname##_groups),	\
+	}
+
+/* PAD PULL UP/DOWN CONFIGURES */
+#define PULLCTL_CONF(pull_reg, pull_sft, pull_wdt)	\
+	{						\
+		.reg = PAD_PULLCTL##pull_reg,		\
+		.shift = pull_sft,			\
+		.width = pull_wdt,			\
+	}
+
+#define PAD_PULLCTL_CONF(pad_name, pull_reg, pull_sft, pull_wdt)	\
+	struct owl_pullctl pad_name##_pullctl_conf			\
+		= PULLCTL_CONF(pull_reg, pull_sft, pull_wdt)
+
+#define ST_CONF(st_reg, st_sft, st_wdt)			\
+	{						\
+		.reg = PAD_ST##st_reg,			\
+		.shift = st_sft,			\
+		.width = st_wdt,			\
+	}
+
+#define PAD_ST_CONF(pad_name, st_reg, st_sft, st_wdt)	\
+	struct owl_st pad_name##_st_conf		\
+		= ST_CONF(st_reg, st_sft, st_wdt)
+
+#define PAD_INFO(name)					\
+	{						\
+		.pad = name,				\
+		.pullctl = NULL,			\
+		.st = NULL,				\
+	}
+
+#define PAD_INFO_ST(name)				\
+	{						\
+		.pad = name,				\
+		.pullctl = NULL,			\
+		.st = &name##_st_conf,			\
+	}
+
+#define PAD_INFO_PULLCTL(name)				\
+	{						\
+		.pad = name,				\
+		.pullctl = &name##_pullctl_conf,	\
+		.st = NULL,				\
+	}
+
+#define PAD_INFO_PULLCTL_ST(name)			\
+	{						\
+		.pad = name,				\
+		.pullctl = &name##_pullctl_conf,	\
+		.st = &name##_st_conf,			\
+	}
+
+#define OWL_GPIO_PORT_A		0
+#define OWL_GPIO_PORT_B		1
+#define OWL_GPIO_PORT_C		2
+#define OWL_GPIO_PORT_D		3
+#define OWL_GPIO_PORT_E		4
+#define OWL_GPIO_PORT_F		5
+
+#define OWL_GPIO_PORT(port, base, count, _outen, _inen, _dat, _intc_ctl,\
+			_intc_pd, _intc_msk, _intc_type, _share)	\
+	[OWL_GPIO_PORT_##port] = {				\
+		.offset = base,					\
+		.pins = count,					\
+		.outen = _outen,				\
+		.inen = _inen,					\
+		.dat = _dat,					\
+		.intc_ctl = _intc_ctl,				\
+		.intc_pd = _intc_pd,				\
+		.intc_msk = _intc_msk,				\
+		.intc_type = _intc_type,			\
+		.shared_ctl_offset = _share,			\
+	}
 
 enum owl_pinconf_drv {
 	OWL_PINCONF_DRV_2MA,
@@ -148,6 +271,7 @@ struct owl_gpio_port {
 	unsigned int intc_pd;
 	unsigned int intc_msk;
 	unsigned int intc_type;
+	u8 shared_ctl_offset;
 };
 
 /**
@@ -174,6 +298,12 @@ struct owl_pinctrl_soc_data {
 	unsigned int ngpios;
 	const struct owl_gpio_port *ports;
 	unsigned int nports;
+	int (*padctl_val2arg)(const struct owl_padinfo *padinfo,
+				unsigned int param,
+				u32 *arg);
+	int (*padctl_arg2val)(const struct owl_padinfo *info,
+				unsigned int param,
+				u32 *arg);
 };
 
 int owl_pinctrl_probe(struct platform_device *pdev,

drivers/pinctrl/actions/pinctrl-s900.c

@@ -13,6 +13,7 @@
 #include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinconf-generic.h>
 #include "pinctrl-owl.h"
 
 /* Pinctrl registers offset */
@@ -33,13 +34,6 @@
 #define PAD_SR1			(0x0274)
 #define PAD_SR2			(0x0278)
 
-#define OWL_GPIO_PORT_A		0
-#define OWL_GPIO_PORT_B		1
-#define OWL_GPIO_PORT_C		2
-#define OWL_GPIO_PORT_D		3
-#define OWL_GPIO_PORT_E		4
-#define OWL_GPIO_PORT_F		5
-
 #define _GPIOA(offset)		(offset)
 #define _GPIOB(offset)		(32 + (offset))
 #define _GPIOC(offset)		(64 + (offset))
@@ -892,55 +886,6 @@ static unsigned int i2c2_sr_pads[]		= { I2C2_SCLK, I2C2_SDATA };
 static unsigned int sensor0_sr_pads[]		= { SENSOR0_PCLK,
 						    SENSOR0_CKOUT };
 
-#define MUX_PG(group_name, reg, shift, width)				\
-	{								\
-		.name = #group_name,					\
-		.pads = group_name##_pads,				\
-		.npads = ARRAY_SIZE(group_name##_pads),			\
-		.funcs = group_name##_funcs,				\
-		.nfuncs = ARRAY_SIZE(group_name##_funcs),		\
-		.mfpctl_reg  = MFCTL##reg,				\
-		.mfpctl_shift = shift,					\
-		.mfpctl_width = width,					\
-		.drv_reg = -1,						\
-		.drv_shift = -1,					\
-		.drv_width = -1,					\
-		.sr_reg = -1,						\
-		.sr_shift = -1,						\
-		.sr_width = -1,						\
-	}
-
-#define DRV_PG(group_name, reg, shift, width)				\
-	{								\
-		.name = #group_name,					\
-		.pads = group_name##_pads,				\
-		.npads = ARRAY_SIZE(group_name##_pads),			\
-		.mfpctl_reg  = -1,					\
-		.mfpctl_shift = -1,					\
-		.mfpctl_width = -1,					\
-		.drv_reg = PAD_DRV##reg,				\
-		.drv_shift = shift,					\
-		.drv_width = width,					\
-		.sr_reg = -1,						\
-		.sr_shift = -1,						\
-		.sr_width = -1,						\
-	}
-
-#define SR_PG(group_name, reg, shift, width)				\
-	{								\
-		.name = #group_name,					\
-		.pads = group_name##_pads,				\
-		.npads = ARRAY_SIZE(group_name##_pads),			\
-		.mfpctl_reg  = -1,					\
-		.mfpctl_shift = -1,					\
-		.mfpctl_width = -1,					\
-		.drv_reg = -1,						\
-		.drv_shift = -1,					\
-		.drv_width = -1,					\
-		.sr_reg = PAD_SR##reg,					\
-		.sr_shift = shift,					\
-		.sr_width = width,					\
-	}
 
 /* Pinctrl groups */
 static const struct owl_pingroup s900_groups[] = {
@@ -1442,13 +1387,6 @@ static const char * const sirq2_groups[] = {
 	"sirq2_dummy",
 };
 
-#define FUNCTION(fname)					\
-	{						\
-		.name = #fname,				\
-		.groups = fname##_groups,		\
-		.ngroups = ARRAY_SIZE(fname##_groups),	\
-	}
-
 static const struct owl_pinmux_func s900_functions[] = {
 	[S900_MUX_ERAM] = FUNCTION(eram),
 	[S900_MUX_ETH_RMII] = FUNCTION(eth_rmii),
@@ -1500,28 +1438,6 @@ static const struct owl_pinmux_func s900_functions[] = {
 	[S900_MUX_SIRQ1] = FUNCTION(sirq1),
 	[S900_MUX_SIRQ2] = FUNCTION(sirq2)
 };
-/* PAD PULL UP/DOWN CONFIGURES */
-#define PULLCTL_CONF(pull_reg, pull_sft, pull_wdt)			\
-	{								\
-		.reg = PAD_PULLCTL##pull_reg,				\
-		.shift = pull_sft,					\
-		.width = pull_wdt,					\
-	}
-
-#define PAD_PULLCTL_CONF(pad_name, pull_reg, pull_sft, pull_wdt)	\
-	struct owl_pullctl pad_name##_pullctl_conf			\
-		= PULLCTL_CONF(pull_reg, pull_sft, pull_wdt)
-
-#define ST_CONF(st_reg, st_sft, st_wdt)					\
-	{								\
-		.reg = PAD_ST##st_reg,					\
-		.shift = st_sft,					\
-		.width = st_wdt,					\
-	}
-
-#define PAD_ST_CONF(pad_name, st_reg, st_sft, st_wdt)			\
-	struct owl_st pad_name##_st_conf				\
-		= ST_CONF(st_reg, st_sft, st_wdt)
 
 /* PAD_PULLCTL0 */
 static PAD_PULLCTL_CONF(ETH_RXER, 0, 18, 2);
@@ -1639,34 +1555,6 @@ static PAD_ST_CONF(SPI0_SS, 1, 2, 1);
 static PAD_ST_CONF(I2S_BCLK0, 1, 1, 1);
 static PAD_ST_CONF(I2S_MCLK0, 1, 0, 1);
 
-#define PAD_INFO(name)							\
-	{								\
-		.pad = name,						\
-		.pullctl = NULL,					\
-		.st = NULL,						\
-	}
-
-#define PAD_INFO_ST(name)						\
-	{								\
-		.pad = name,						\
-		.pullctl = NULL,					\
-		.st = &name##_st_conf,					\
-	}
-
-#define PAD_INFO_PULLCTL(name)						\
-	{								\
-		.pad = name,						\
-		.pullctl = &name##_pullctl_conf,			\
-		.st = NULL,						\
-	}
-
-#define PAD_INFO_PULLCTL_ST(name)					\
-	{								\
-		.pad = name,						\
-		.pullctl = &name##_pullctl_conf,			\
-		.st = &name##_st_conf,					\
-	}
-
 /* Pad info table */
 static struct owl_padinfo s900_padinfo[NUM_PADS] = {
 	[ETH_TXD0] = PAD_INFO_ST(ETH_TXD0),
@@ -1821,29 +1709,76 @@ static struct owl_padinfo s900_padinfo[NUM_PADS] = {
 	[SGPIO3] = PAD_INFO_PULLCTL_ST(SGPIO3)
 };
 
-#define OWL_GPIO_PORT(port, base, count, _outen, _inen, _dat,		\
-			_intc_ctl, _intc_pd, _intc_msk, _intc_type)	\
-	[OWL_GPIO_PORT_##port] = {					\
-		.offset = base,						\
-		.pins = count,						\
-		.outen = _outen,					\
-		.inen = _inen,						\
-		.dat = _dat,						\
-		.intc_ctl = _intc_ctl,					\
-		.intc_pd = _intc_pd,					\
-		.intc_msk = _intc_msk,					\
-		.intc_type = _intc_type,				\
-	}
-
 static const struct owl_gpio_port s900_gpio_ports[] = {
-	OWL_GPIO_PORT(A, 0x0000, 32, 0x0, 0x4, 0x8, 0x204, 0x208, 0x20C, 0x240),
-	OWL_GPIO_PORT(B, 0x000C, 32, 0x0, 0x4, 0x8, 0x534, 0x204, 0x208, 0x23C),
-	OWL_GPIO_PORT(C, 0x0018, 12, 0x0, 0x4, 0x8, 0x52C, 0x200, 0x204, 0x238),
-	OWL_GPIO_PORT(D, 0x0024, 30, 0x0, 0x4, 0x8, 0x524, 0x1FC, 0x200, 0x234),
-	OWL_GPIO_PORT(E, 0x0030, 32, 0x0, 0x4, 0x8, 0x51C, 0x1F8, 0x1FC, 0x230),
-	OWL_GPIO_PORT(F, 0x00F0, 8, 0x0, 0x4, 0x8, 0x460, 0x140, 0x144, 0x178)
+	OWL_GPIO_PORT(A, 0x0000, 32, 0x0, 0x4, 0x8, 0x204, 0x208, 0x20C, 0x240, 0),
+	OWL_GPIO_PORT(B, 0x000C, 32, 0x0, 0x4, 0x8, 0x534, 0x204, 0x208, 0x23C, 0),
+	OWL_GPIO_PORT(C, 0x0018, 12, 0x0, 0x4, 0x8, 0x52C, 0x200, 0x204, 0x238, 0),
+	OWL_GPIO_PORT(D, 0x0024, 30, 0x0, 0x4, 0x8, 0x524, 0x1FC, 0x200, 0x234, 0),
+	OWL_GPIO_PORT(E, 0x0030, 32, 0x0, 0x4, 0x8, 0x51C, 0x1F8, 0x1FC, 0x230, 0),
+	OWL_GPIO_PORT(F, 0x00F0, 8, 0x0, 0x4, 0x8, 0x460, 0x140, 0x144, 0x178, 0)
 };
 
+enum s900_pinconf_pull {
+	OWL_PINCONF_PULL_HIZ,
+	OWL_PINCONF_PULL_DOWN,
+	OWL_PINCONF_PULL_UP,
+	OWL_PINCONF_PULL_HOLD,
+};
+
+static int s900_pad_pinconf_arg2val(const struct owl_padinfo *info,
+				unsigned int param,
+				u32 *arg)
+{
+	switch (param) {
+	case PIN_CONFIG_BIAS_BUS_HOLD:
+		*arg = OWL_PINCONF_PULL_HOLD;
+		break;
+	case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+		*arg = OWL_PINCONF_PULL_HIZ;
+		break;
+	case PIN_CONFIG_BIAS_PULL_DOWN:
+		*arg = OWL_PINCONF_PULL_DOWN;
+		break;
+	case PIN_CONFIG_BIAS_PULL_UP:
+		*arg = OWL_PINCONF_PULL_UP;
+		break;
+	case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+		*arg = (*arg >= 1 ? 1 : 0);
+		break;
+	default:
+		return -ENOTSUPP;
+	}
+
+	return 0;
+}
+
+static int s900_pad_pinconf_val2arg(const struct owl_padinfo *padinfo,
+				unsigned int param,
+				u32 *arg)
+{
+	switch (param) {
+	case PIN_CONFIG_BIAS_BUS_HOLD:
+		*arg = *arg == OWL_PINCONF_PULL_HOLD;
+		break;
+	case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+		*arg = *arg == OWL_PINCONF_PULL_HIZ;
+		break;
+	case PIN_CONFIG_BIAS_PULL_DOWN:
+		*arg = *arg == OWL_PINCONF_PULL_DOWN;
+		break;
+	case PIN_CONFIG_BIAS_PULL_UP:
+		*arg = *arg == OWL_PINCONF_PULL_UP;
+		break;
+	case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+		*arg = *arg == 1;
+		break;
+	default:
+		return -ENOTSUPP;
+	}
+
+	return 0;
+}
+
 static struct owl_pinctrl_soc_data s900_pinctrl_data = {
 	.padinfo = s900_padinfo,
 	.pins = (const struct pinctrl_pin_desc *)s900_pads,
@@ -1854,7 +1789,9 @@ static struct owl_pinctrl_soc_data s900_pinctrl_data = {
 	.ngroups = ARRAY_SIZE(s900_groups),
 	.ngpios = NUM_GPIOS,
 	.ports = s900_gpio_ports,
-	.nports = ARRAY_SIZE(s900_gpio_ports)
+	.nports = ARRAY_SIZE(s900_gpio_ports),
+	.padctl_arg2val = s900_pad_pinconf_arg2val,
+	.padctl_val2arg = s900_pad_pinconf_val2arg,
 };
 
 static int s900_pinctrl_probe(struct platform_device *pdev)

drivers/pinctrl/aspeed/Makefile

 # Aspeed pinctrl support
 
-ccflags-y += -Woverride-init
+ccflags-y += $(call cc-option,-Woverride-init)
 obj-$(CONFIG_PINCTRL_ASPEED)	+= pinctrl-aspeed.o
 obj-$(CONFIG_PINCTRL_ASPEED_G4)	+= pinctrl-aspeed-g4.o
 obj-$(CONFIG_PINCTRL_ASPEED_G5)	+= pinctrl-aspeed-g5.o

drivers/pinctrl/bcm/pinctrl-bcm2835.c

+// SPDX-License-Identifier: GPL-2.0+
 /*
  * Driver for Broadcom BCM2835 GPIO unit (pinctrl + GPIO)
  *
@@ -6,16 +7,6 @@
  * This driver is inspired by:
  * pinctrl-nomadik.c, please see original file for copyright information
  * pinctrl-tegra.c, please see original file for copyright information
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <linux/bitmap.h>
@@ -72,10 +63,8 @@
 #define GPIO_REG_OFFSET(p)	((p) / 32)
 #define GPIO_REG_SHIFT(p)	((p) % 32)
 
-enum bcm2835_pinconf_param {
-	/* argument: bcm2835_pinconf_pull */
-	BCM2835_PINCONF_PARAM_PULL = (PIN_CONFIG_END + 1),
-};
+/* argument: bcm2835_pinconf_pull */
+#define BCM2835_PINCONF_PARAM_PULL	(PIN_CONFIG_END + 1)
 
 struct bcm2835_pinctrl {
 	struct device *dev;
@@ -90,7 +79,7 @@ struct bcm2835_pinctrl {
 	struct gpio_chip gpio_chip;
 	struct pinctrl_gpio_range gpio_range;
 
-	spinlock_t irq_lock[BCM2835_NUM_BANKS];
+	raw_spinlock_t irq_lock[BCM2835_NUM_BANKS];
 };
 
 /* pins are just named GPIO0..GPIO53 */
@@ -461,10 +450,10 @@ static void bcm2835_gpio_irq_enable(struct irq_data *data)
 	unsigned bank = GPIO_REG_OFFSET(gpio);
 	unsigned long flags;
 
-	spin_lock_irqsave(&pc->irq_lock[bank], flags);
+	raw_spin_lock_irqsave(&pc->irq_lock[bank], flags);
 	set_bit(offset, &pc->enabled_irq_map[bank]);
 	bcm2835_gpio_irq_config(pc, gpio, true);
-	spin_unlock_irqrestore(&pc->irq_lock[bank], flags);
+	raw_spin_unlock_irqrestore(&pc->irq_lock[bank], flags);
 }
 
 static void bcm2835_gpio_irq_disable(struct irq_data *data)
@@ -476,12 +465,12 @@ static void bcm2835_gpio_irq_disable(struct irq_data *data)
 	unsigned bank = GPIO_REG_OFFSET(gpio);
 	unsigned long flags;
 
-	spin_lock_irqsave(&pc->irq_lock[bank], flags);
+	raw_spin_lock_irqsave(&pc->irq_lock[bank], flags);
 	bcm2835_gpio_irq_config(pc, gpio, false);
 	/* Clear events that were latched prior to clearing event sources */
 	bcm2835_gpio_set_bit(pc, GPEDS0, gpio);
 	clear_bit(offset, &pc->enabled_irq_map[bank]);
-	spin_unlock_irqrestore(&pc->irq_lock[bank], flags);
+	raw_spin_unlock_irqrestore(&pc->irq_lock[bank], flags);
 }
 
 static int __bcm2835_gpio_irq_set_type_disabled(struct bcm2835_pinctrl *pc,
@@ -584,7 +573,7 @@ static int bcm2835_gpio_irq_set_type(struct irq_data *data, unsigned int type)
 	unsigned long flags;
 	int ret;
 
-	spin_lock_irqsave(&pc->irq_lock[bank], flags);
+	raw_spin_lock_irqsave(&pc->irq_lock[bank], flags);
 
 	if (test_bit(offset, &pc->enabled_irq_map[bank]))
 		ret = __bcm2835_gpio_irq_set_type_enabled(pc, gpio, type);
@@ -596,7 +585,7 @@ static int bcm2835_gpio_irq_set_type(struct irq_data *data, unsigned int type)
 	else
 		irq_set_handler_locked(data, handle_level_irq);
 
-	spin_unlock_irqrestore(&pc->irq_lock[bank], flags);
+	raw_spin_unlock_irqrestore(&pc->irq_lock[bank], flags);
 
 	return ret;
 }
@@ -1047,7 +1036,7 @@ static int bcm2835_pinctrl_probe(struct platform_device *pdev)
 		for_each_set_bit(offset, &events, 32)
 			bcm2835_gpio_wr(pc, GPEDS0 + i * 4, BIT(offset));
 
-		spin_lock_init(&pc->irq_lock[i]);
+		raw_spin_lock_init(&pc->irq_lock[i]);
 	}
 
 	err = gpiochip_add_data(&pc->gpio_chip, pc);

drivers/pinctrl/bcm/pinctrl-ns.c

@@ -5,6 +5,7 @@
 
 #include <linux/err.h>
 #include <linux/io.h>
+#include <linux/mfd/syscon.h>
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
@@ -12,6 +13,7 @@
 #include <linux/pinctrl/pinctrl.h>
 #include <linux/pinctrl/pinmux.h>
 #include <linux/platform_device.h>
+#include <linux/regmap.h>
 #include <linux/slab.h>
 
 #define FLAG_BCM4708		BIT(1)
@@ -22,7 +24,8 @@ struct ns_pinctrl {
 	struct device *dev;
 	unsigned int chipset_flag;
 	struct pinctrl_dev *pctldev;
-	void __iomem *base;
+	struct regmap *regmap;
+	u32 offset;
 
 	struct pinctrl_desc pctldesc;
 	struct ns_pinctrl_group *groups;
@@ -229,9 +232,9 @@ static int ns_pinctrl_set_mux(struct pinctrl_dev *pctrl_dev,
 		unset |= BIT(pin_number);
 	}
 
-	tmp = readl(ns_pinctrl->base);
+	regmap_read(ns_pinctrl->regmap, ns_pinctrl->offset, &tmp);
 	tmp &= ~unset;
-	writel(tmp, ns_pinctrl->base);
+	regmap_write(ns_pinctrl->regmap, ns_pinctrl->offset, tmp);
 
 	return 0;
 }
@@ -263,13 +266,13 @@ static const struct of_device_id ns_pinctrl_of_match_table[] = {
 static int ns_pinctrl_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
 	const struct of_device_id *of_id;
 	struct ns_pinctrl *ns_pinctrl;
 	struct pinctrl_desc *pctldesc;
 	struct pinctrl_pin_desc *pin;
 	struct ns_pinctrl_group *group;
 	struct ns_pinctrl_function *function;
-	struct resource *res;
 	int i;
 
 	ns_pinctrl = devm_kzalloc(dev, sizeof(*ns_pinctrl), GFP_KERNEL);
@@ -287,12 +290,18 @@ static int ns_pinctrl_probe(struct platform_device *pdev)
 		return -EINVAL;
 	ns_pinctrl->chipset_flag = (uintptr_t)of_id->data;
 
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
-					   "cru_gpio_control");
-	ns_pinctrl->base = devm_ioremap_resource(dev, res);
-	if (IS_ERR(ns_pinctrl->base)) {
-		dev_err(dev, "Failed to map pinctrl regs\n");
-		return PTR_ERR(ns_pinctrl->base);
+	ns_pinctrl->regmap = syscon_node_to_regmap(of_get_parent(np));
+	if (IS_ERR(ns_pinctrl->regmap)) {
+		int err = PTR_ERR(ns_pinctrl->regmap);
+
+		dev_err(dev, "Failed to map pinctrl regs: %d\n", err);
+
+		return err;
+	}
+
+	if (of_property_read_u32(np, "offset", &ns_pinctrl->offset)) {
+		dev_err(dev, "Failed to get register offset\n");
+		return -ENOENT;
 	}
 
 	memcpy(pctldesc, &ns_pinctrl_desc, sizeof(*pctldesc));

drivers/pinctrl/freescale/Kconfig

@@ -5,6 +5,11 @@ config PINCTRL_IMX
 	select GENERIC_PINCONF
 	select REGMAP
 
+config PINCTRL_IMX_SCU
+	bool
+	depends on IMX_SCU
+	select PINCTRL_IMX
+
 config PINCTRL_IMX1_CORE
 	bool
 	select PINMUX
@@ -119,11 +124,18 @@ config PINCTRL_IMX7ULP
 
 config PINCTRL_IMX8MQ
 	bool "IMX8MQ pinctrl driver"
-	depends on SOC_IMX8MQ
+	depends on ARCH_MXC && ARM64
 	select PINCTRL_IMX
 	help
 	  Say Y here to enable the imx8mq pinctrl driver
 
+config PINCTRL_IMX8QXP
+	bool "IMX8QXP pinctrl driver"
+	depends on ARCH_MXC && ARM64
+	select PINCTRL_IMX_SCU
+	help
+	  Say Y here to enable the imx8qxp pinctrl driver
+
 config PINCTRL_VF610
 	bool "Freescale Vybrid VF610 pinctrl driver"
 	depends on SOC_VF610

drivers/pinctrl/freescale/Makefile

 # SPDX-License-Identifier: GPL-2.0
 # Freescale pin control drivers
 obj-$(CONFIG_PINCTRL_IMX)	+= pinctrl-imx.o
+obj-$(CONFIG_PINCTRL_IMX_SCU)	+= pinctrl-scu.o
 obj-$(CONFIG_PINCTRL_IMX1_CORE)	+= pinctrl-imx1-core.o
 obj-$(CONFIG_PINCTRL_IMX1)	+= pinctrl-imx1.o
 obj-$(CONFIG_PINCTRL_IMX21)	+= pinctrl-imx21.o
@@ -18,6 +19,7 @@ obj-$(CONFIG_PINCTRL_IMX6UL)	+= pinctrl-imx6ul.o
 obj-$(CONFIG_PINCTRL_IMX7D)	+= pinctrl-imx7d.o
 obj-$(CONFIG_PINCTRL_IMX7ULP)	+= pinctrl-imx7ulp.o
 obj-$(CONFIG_PINCTRL_IMX8MQ)	+= pinctrl-imx8mq.o
+obj-$(CONFIG_PINCTRL_IMX8QXP)	+= pinctrl-imx8qxp.o
 obj-$(CONFIG_PINCTRL_VF610)	+= pinctrl-vf610.o
 obj-$(CONFIG_PINCTRL_MXS)	+= pinctrl-mxs.o
 obj-$(CONFIG_PINCTRL_IMX23)	+= pinctrl-imx23.o

drivers/pinctrl/freescale/pinctrl-imx.h

@@ -19,22 +19,43 @@ struct platform_device;
 extern struct pinmux_ops imx_pmx_ops;
 
 /**
- * struct imx_pin - describes a single i.MX pin
- * @pin: the pin_id of this pin
+ * struct imx_pin_mmio - MMIO pin configurations
  * @mux_mode: the mux mode for this pin.
  * @input_reg: the select input register offset for this pin if any
  *	0 if no select input setting needed.
  * @input_val: the select input value for this pin.
  * @configs: the config for this pin.
  */
-struct imx_pin {
-	unsigned int pin;
+struct imx_pin_mmio {
 	unsigned int mux_mode;
 	u16 input_reg;
 	unsigned int input_val;
 	unsigned long config;
 };
 
+/**
+ * struct imx_pin_scu - SCU pin configurations
+ * @mux: the mux mode for this pin.
+ * @configs: the config for this pin.
+ */
+struct imx_pin_scu {
+	unsigned int mux_mode;
+	unsigned long config;
+};
+
+/**
+ * struct imx_pin - describes a single i.MX pin
+ * @pin: the pin_id of this pin
+ * @conf: config type of this pin, either mmio or scu
+ */
+struct imx_pin {
+	unsigned int pin;
+	union {
+		struct imx_pin_mmio mmio;
+		struct imx_pin_scu scu;
+	} conf;
+};
+
 /**
  * struct imx_pin_reg - describe a pin reg map
  * @mux_reg: mux register offset
@@ -99,8 +120,9 @@ struct imx_pinctrl {
 #define IMX_CFG_PARAMS_DECODE_INVERT(p, m, o) \
 	{ .param = p, .mask = m, .shift = o, .invert = true, }
 
-#define SHARE_MUX_CONF_REG	0x1
-#define ZERO_OFFSET_VALID	0x2
+#define SHARE_MUX_CONF_REG	BIT(0)
+#define ZERO_OFFSET_VALID	BIT(1)
+#define IMX_USE_SCU		BIT(2)
 
 #define NO_MUX		0x0
 #define NO_PAD		0x0
@@ -113,4 +135,37 @@ struct imx_pinctrl {
 
 int imx_pinctrl_probe(struct platform_device *pdev,
 			const struct imx_pinctrl_soc_info *info);
+
+#ifdef CONFIG_PINCTRL_IMX_SCU
+#define BM_PAD_CTL_GP_ENABLE		BIT(30)
+#define BM_PAD_CTL_IFMUX_ENABLE		BIT(31)
+#define BP_PAD_CTL_IFMUX		27
+
+int imx_pinctrl_sc_ipc_init(struct platform_device *pdev);
+int imx_pinconf_get_scu(struct pinctrl_dev *pctldev, unsigned pin_id,
+			unsigned long *config);
+int imx_pinconf_set_scu(struct pinctrl_dev *pctldev, unsigned pin_id,
+			unsigned long *configs, unsigned num_configs);
+void imx_pinctrl_parse_pin_scu(struct imx_pinctrl *ipctl,
+			       unsigned int *pin_id, struct imx_pin *pin,
+			       const __be32 **list_p);
+#else
+static inline int imx_pinconf_get_scu(struct pinctrl_dev *pctldev,
+				      unsigned pin_id, unsigned long *config)
+{
+	return -EINVAL;
+}
+static inline int imx_pinconf_set_scu(struct pinctrl_dev *pctldev,
+				      unsigned pin_id, unsigned long *configs,
+				      unsigned num_configs)
+{
+	return -EINVAL;
+}
+static inline void imx_pinctrl_parse_pin_scu(struct imx_pinctrl *ipctl,
+					    unsigned int *pin_id,
+					    struct imx_pin *pin,
+					    const __be32 **list_p)
+{
+}
+#endif
 #endif /* __DRIVERS_PINCTRL_IMX_H */

drivers/pinctrl/freescale/pinctrl-imx7ulp.c

@@ -256,46 +256,8 @@ static const struct pinctrl_pin_desc imx7ulp_pinctrl_pads[] = {
 
 #define BM_OBE_ENABLED		BIT(17)
 #define BM_IBE_ENABLED		BIT(16)
-#define BM_LK_ENABLED		BIT(15)
 #define BM_MUX_MODE		0xf00
 #define BP_MUX_MODE		8
-#define BM_PULL_ENABLED		BIT(1)
-
-static const struct imx_cfg_params_decode imx7ulp_cfg_decodes[] = {
-	IMX_CFG_PARAMS_DECODE(PIN_CONFIG_DRIVE_STRENGTH, 		BIT(6), 6),
-	IMX_CFG_PARAMS_DECODE(PIN_CONFIG_DRIVE_PUSH_PULL,		BIT(5), 5),
-	IMX_CFG_PARAMS_DECODE(PIN_CONFIG_SLEW_RATE,			BIT(2), 2),
-	IMX_CFG_PARAMS_DECODE(PIN_CONFIG_BIAS_DISABLE,			BIT(1), 1),
-	IMX_CFG_PARAMS_DECODE(PIN_CONFIG_BIAS_PULL_UP,			BIT(0), 0),
-
-	IMX_CFG_PARAMS_DECODE_INVERT(PIN_CONFIG_DRIVE_OPEN_DRAIN,	BIT(5), 5),
-	IMX_CFG_PARAMS_DECODE_INVERT(PIN_CONFIG_BIAS_PULL_DOWN,		BIT(0), 0),
-};
-
-static void imx7ulp_cfg_params_fixup(unsigned long *configs,
-				    unsigned int num_configs,
-				    u32 *raw_config)
-{
-	enum pin_config_param param;
-	u32 param_val;
-	int i;
-
-	/* lock field disabled */
-	*raw_config &= ~BM_LK_ENABLED;
-
-	for (i = 0; i < num_configs; i++) {
-		param = pinconf_to_config_param(configs[i]);
-		param_val = pinconf_to_config_argument(configs[i]);
-
-		if ((param == PIN_CONFIG_BIAS_PULL_UP) ||
-		    (param == PIN_CONFIG_BIAS_PULL_DOWN)) {
-			/* pull enabled */
-			*raw_config |= BM_PULL_ENABLED;
-
-			return;
-		}
-	}
-}
 
 static int imx7ulp_pmx_gpio_set_direction(struct pinctrl_dev *pctldev,
 					  struct pinctrl_gpio_range *range,
@@ -326,10 +288,6 @@ static const struct imx_pinctrl_soc_info imx7ulp_pinctrl_info = {
 	.gpio_set_direction = imx7ulp_pmx_gpio_set_direction,
 	.mux_mask = BM_MUX_MODE,
 	.mux_shift = BP_MUX_MODE,
-	.generic_pinconf = true,
-	.decodes = imx7ulp_cfg_decodes,
-	.num_decodes = ARRAY_SIZE(imx7ulp_cfg_decodes),
-	.fixup = imx7ulp_cfg_params_fixup,
 };
 
 static const struct of_device_id imx7ulp_pinctrl_of_match[] = {

drivers/pinctrl/freescale/pinctrl-imx8qxp.c

+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ * Copyright 2017-2018 NXP
+ *	Dong Aisheng <aisheng.dong@nxp.com>
+ */
+
+#include <dt-bindings/pinctrl/pads-imx8qxp.h>
+#include <linux/err.h>
+#include <linux/firmware/imx/sci.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-imx.h"
+
+static const struct pinctrl_pin_desc imx8qxp_pinctrl_pads[] = {
+	IMX_PINCTRL_PIN(IMX8QXP_PCIE_CTRL0_PERST_B),
+	IMX_PINCTRL_PIN(IMX8QXP_PCIE_CTRL0_CLKREQ_B),
+	IMX_PINCTRL_PIN(IMX8QXP_PCIE_CTRL0_WAKE_B),
+	IMX_PINCTRL_PIN(IMX8QXP_COMP_CTL_GPIO_1V8_3V3_PCIESEP),
+	IMX_PINCTRL_PIN(IMX8QXP_USB_SS3_TC0),
+	IMX_PINCTRL_PIN(IMX8QXP_USB_SS3_TC1),
+	IMX_PINCTRL_PIN(IMX8QXP_USB_SS3_TC2),
+	IMX_PINCTRL_PIN(IMX8QXP_USB_SS3_TC3),
+	IMX_PINCTRL_PIN(IMX8QXP_COMP_CTL_GPIO_3V3_USB3IO),
+	IMX_PINCTRL_PIN(IMX8QXP_EMMC0_CLK),
+	IMX_PINCTRL_PIN(IMX8QXP_EMMC0_CMD),
+	IMX_PINCTRL_PIN(IMX8QXP_EMMC0_DATA0),
+	IMX_PINCTRL_PIN(IMX8QXP_EMMC0_DATA1),
+	IMX_PINCTRL_PIN(IMX8QXP_EMMC0_DATA2),
+	IMX_PINCTRL_PIN(IMX8QXP_EMMC0_DATA3),
+	IMX_PINCTRL_PIN(IMX8QXP_COMP_CTL_GPIO_1V8_3V3_SD1FIX0),
+	IMX_PINCTRL_PIN(IMX8QXP_EMMC0_DATA4),
+	IMX_PINCTRL_PIN(IMX8QXP_EMMC0_DATA5),
+	IMX_PINCTRL_PIN(IMX8QXP_EMMC0_DATA6),
+	IMX_PINCTRL_PIN(IMX8QXP_EMMC0_DATA7),
+	IMX_PINCTRL_PIN(IMX8QXP_EMMC0_STROBE),
+	IMX_PINCTRL_PIN(IMX8QXP_EMMC0_RESET_B),
+	IMX_PINCTRL_PIN(IMX8QXP_COMP_CTL_GPIO_1V8_3V3_SD1FIX1),
+	IMX_PINCTRL_PIN(IMX8QXP_USDHC1_RESET_B),
+	IMX_PINCTRL_PIN(IMX8QXP_USDHC1_VSELECT),
+	IMX_PINCTRL_PIN(IMX8QXP_CTL_NAND_RE_P_N),
+	IMX_PINCTRL_PIN(IMX8QXP_USDHC1_WP),
+	IMX_PINCTRL_PIN(IMX8QXP_USDHC1_CD_B),
+	IMX_PINCTRL_PIN(IMX8QXP_CTL_NAND_DQS_P_N),
+	IMX_PINCTRL_PIN(IMX8QXP_COMP_CTL_GPIO_1V8_3V3_VSELSEP),
+	IMX_PINCTRL_PIN(IMX8QXP_USDHC1_CLK),
+	IMX_PINCTRL_PIN(IMX8QXP_USDHC1_CMD),
+	IMX_PINCTRL_PIN(IMX8QXP_USDHC1_DATA0),
+	IMX_PINCTRL_PIN(IMX8QXP_USDHC1_DATA1),
+	IMX_PINCTRL_PIN(IMX8QXP_USDHC1_DATA2),
+	IMX_PINCTRL_PIN(IMX8QXP_USDHC1_DATA3),
+	IMX_PINCTRL_PIN(IMX8QXP_COMP_CTL_GPIO_1V8_3V3_VSEL3),
+	IMX_PINCTRL_PIN(IMX8QXP_ENET0_RGMII_TXC),
+	IMX_PINCTRL_PIN(IMX8QXP_ENET0_RGMII_TX_CTL),
+	IMX_PINCTRL_PIN(IMX8QXP_ENET0_RGMII_TXD0),
+	IMX_PINCTRL_PIN(IMX8QXP_ENET0_RGMII_TXD1),
+	IMX_PINCTRL_PIN(IMX8QXP_ENET0_RGMII_TXD2),
+	IMX_PINCTRL_PIN(IMX8QXP_ENET0_RGMII_TXD3),
+	IMX_PINCTRL_PIN(IMX8QXP_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB0),
+	IMX_PINCTRL_PIN(IMX8QXP_ENET0_RGMII_RXC),
+	IMX_PINCTRL_PIN(IMX8QXP_ENET0_RGMII_RX_CTL),
+	IMX_PINCTRL_PIN(IMX8QXP_ENET0_RGMII_RXD0),
+	IMX_PINCTRL_PIN(IMX8QXP_ENET0_RGMII_RXD1),
+	IMX_PINCTRL_PIN(IMX8QXP_ENET0_RGMII_RXD2),
+	IMX_PINCTRL_PIN(IMX8QXP_ENET0_RGMII_RXD3),
+	IMX_PINCTRL_PIN(IMX8QXP_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB1),
+	IMX_PINCTRL_PIN(IMX8QXP_ENET0_REFCLK_125M_25M),
+	IMX_PINCTRL_PIN(IMX8QXP_ENET0_MDIO),
+	IMX_PINCTRL_PIN(IMX8QXP_ENET0_MDC),
+	IMX_PINCTRL_PIN(IMX8QXP_COMP_CTL_GPIO_1V8_3V3_GPIOCT),
+	IMX_PINCTRL_PIN(IMX8QXP_ESAI0_FSR),
+	IMX_PINCTRL_PIN(IMX8QXP_ESAI0_FST),
+	IMX_PINCTRL_PIN(IMX8QXP_ESAI0_SCKR),
+	IMX_PINCTRL_PIN(IMX8QXP_ESAI0_SCKT),
+	IMX_PINCTRL_PIN(IMX8QXP_ESAI0_TX0),
+	IMX_PINCTRL_PIN(IMX8QXP_ESAI0_TX1),
+	IMX_PINCTRL_PIN(IMX8QXP_ESAI0_TX2_RX3),
+	IMX_PINCTRL_PIN(IMX8QXP_ESAI0_TX3_RX2),
+	IMX_PINCTRL_PIN(IMX8QXP_ESAI0_TX4_RX1),
+	IMX_PINCTRL_PIN(IMX8QXP_ESAI0_TX5_RX0),
+	IMX_PINCTRL_PIN(IMX8QXP_SPDIF0_RX),
+	IMX_PINCTRL_PIN(IMX8QXP_SPDIF0_TX),
+	IMX_PINCTRL_PIN(IMX8QXP_SPDIF0_EXT_CLK),
+	IMX_PINCTRL_PIN(IMX8QXP_COMP_CTL_GPIO_1V8_3V3_GPIORHB),
+	IMX_PINCTRL_PIN(IMX8QXP_SPI3_SCK),
+	IMX_PINCTRL_PIN(IMX8QXP_SPI3_SDO),
+	IMX_PINCTRL_PIN(IMX8QXP_SPI3_SDI),
+	IMX_PINCTRL_PIN(IMX8QXP_SPI3_CS0),
+	IMX_PINCTRL_PIN(IMX8QXP_SPI3_CS1),
+	IMX_PINCTRL_PIN(IMX8QXP_MCLK_IN1),
+	IMX_PINCTRL_PIN(IMX8QXP_MCLK_IN0),
+	IMX_PINCTRL_PIN(IMX8QXP_MCLK_OUT0),
+	IMX_PINCTRL_PIN(IMX8QXP_UART1_TX),
+	IMX_PINCTRL_PIN(IMX8QXP_UART1_RX),
+	IMX_PINCTRL_PIN(IMX8QXP_UART1_RTS_B),
+	IMX_PINCTRL_PIN(IMX8QXP_UART1_CTS_B),
+	IMX_PINCTRL_PIN(IMX8QXP_COMP_CTL_GPIO_1V8_3V3_GPIORHK),
+	IMX_PINCTRL_PIN(IMX8QXP_SAI0_TXD),
+	IMX_PINCTRL_PIN(IMX8QXP_SAI0_TXC),
+	IMX_PINCTRL_PIN(IMX8QXP_SAI0_RXD),
+	IMX_PINCTRL_PIN(IMX8QXP_SAI0_TXFS),
+	IMX_PINCTRL_PIN(IMX8QXP_SAI1_RXD),
+	IMX_PINCTRL_PIN(IMX8QXP_SAI1_RXC),
+	IMX_PINCTRL_PIN(IMX8QXP_SAI1_RXFS),
+	IMX_PINCTRL_PIN(IMX8QXP_SPI2_CS0),
+	IMX_PINCTRL_PIN(IMX8QXP_SPI2_SDO),
+	IMX_PINCTRL_PIN(IMX8QXP_SPI2_SDI),
+	IMX_PINCTRL_PIN(IMX8QXP_SPI2_SCK),
+	IMX_PINCTRL_PIN(IMX8QXP_SPI0_SCK),
+	IMX_PINCTRL_PIN(IMX8QXP_SPI0_SDI),
+	IMX_PINCTRL_PIN(IMX8QXP_SPI0_SDO),
+	IMX_PINCTRL_PIN(IMX8QXP_SPI0_CS1),
+	IMX_PINCTRL_PIN(IMX8QXP_SPI0_CS0),
+	IMX_PINCTRL_PIN(IMX8QXP_COMP_CTL_GPIO_1V8_3V3_GPIORHT),
+	IMX_PINCTRL_PIN(IMX8QXP_ADC_IN1),
+	IMX_PINCTRL_PIN(IMX8QXP_ADC_IN0),
+	IMX_PINCTRL_PIN(IMX8QXP_ADC_IN3),
+	IMX_PINCTRL_PIN(IMX8QXP_ADC_IN2),
+	IMX_PINCTRL_PIN(IMX8QXP_ADC_IN5),
+	IMX_PINCTRL_PIN(IMX8QXP_ADC_IN4),
+	IMX_PINCTRL_PIN(IMX8QXP_FLEXCAN0_RX),
+	IMX_PINCTRL_PIN(IMX8QXP_FLEXCAN0_TX),
+	IMX_PINCTRL_PIN(IMX8QXP_FLEXCAN1_RX),
+	IMX_PINCTRL_PIN(IMX8QXP_FLEXCAN1_TX),
+	IMX_PINCTRL_PIN(IMX8QXP_FLEXCAN2_RX),
+	IMX_PINCTRL_PIN(IMX8QXP_FLEXCAN2_TX),
+	IMX_PINCTRL_PIN(IMX8QXP_UART0_RX),
+	IMX_PINCTRL_PIN(IMX8QXP_UART0_TX),
+	IMX_PINCTRL_PIN(IMX8QXP_UART2_TX),
+	IMX_PINCTRL_PIN(IMX8QXP_UART2_RX),
+	IMX_PINCTRL_PIN(IMX8QXP_COMP_CTL_GPIO_1V8_3V3_GPIOLH),
+	IMX_PINCTRL_PIN(IMX8QXP_MIPI_DSI0_I2C0_SCL),
+	IMX_PINCTRL_PIN(IMX8QXP_MIPI_DSI0_I2C0_SDA),
+	IMX_PINCTRL_PIN(IMX8QXP_MIPI_DSI0_GPIO0_00),
+	IMX_PINCTRL_PIN(IMX8QXP_MIPI_DSI0_GPIO0_01),
+	IMX_PINCTRL_PIN(IMX8QXP_MIPI_DSI1_I2C0_SCL),
+	IMX_PINCTRL_PIN(IMX8QXP_MIPI_DSI1_I2C0_SDA),
+	IMX_PINCTRL_PIN(IMX8QXP_MIPI_DSI1_GPIO0_00),
+	IMX_PINCTRL_PIN(IMX8QXP_MIPI_DSI1_GPIO0_01),
+	IMX_PINCTRL_PIN(IMX8QXP_COMP_CTL_GPIO_1V8_3V3_MIPIDSIGPIO),
+	IMX_PINCTRL_PIN(IMX8QXP_JTAG_TRST_B),
+	IMX_PINCTRL_PIN(IMX8QXP_PMIC_I2C_SCL),
+	IMX_PINCTRL_PIN(IMX8QXP_PMIC_I2C_SDA),
+	IMX_PINCTRL_PIN(IMX8QXP_PMIC_INT_B),
+	IMX_PINCTRL_PIN(IMX8QXP_SCU_GPIO0_00),
+	IMX_PINCTRL_PIN(IMX8QXP_SCU_GPIO0_01),
+	IMX_PINCTRL_PIN(IMX8QXP_SCU_PMIC_STANDBY),
+	IMX_PINCTRL_PIN(IMX8QXP_SCU_BOOT_MODE0),
+	IMX_PINCTRL_PIN(IMX8QXP_SCU_BOOT_MODE1),
+	IMX_PINCTRL_PIN(IMX8QXP_SCU_BOOT_MODE2),
+	IMX_PINCTRL_PIN(IMX8QXP_SCU_BOOT_MODE3),
+	IMX_PINCTRL_PIN(IMX8QXP_CSI_D00),
+	IMX_PINCTRL_PIN(IMX8QXP_CSI_D01),
+	IMX_PINCTRL_PIN(IMX8QXP_CSI_D02),
+	IMX_PINCTRL_PIN(IMX8QXP_CSI_D03),
+	IMX_PINCTRL_PIN(IMX8QXP_CSI_D04),
+	IMX_PINCTRL_PIN(IMX8QXP_CSI_D05),
+	IMX_PINCTRL_PIN(IMX8QXP_CSI_D06),
+	IMX_PINCTRL_PIN(IMX8QXP_CSI_D07),
+	IMX_PINCTRL_PIN(IMX8QXP_CSI_HSYNC),
+	IMX_PINCTRL_PIN(IMX8QXP_CSI_VSYNC),
+	IMX_PINCTRL_PIN(IMX8QXP_CSI_PCLK),
+	IMX_PINCTRL_PIN(IMX8QXP_CSI_MCLK),
+	IMX_PINCTRL_PIN(IMX8QXP_CSI_EN),
+	IMX_PINCTRL_PIN(IMX8QXP_CSI_RESET),
+	IMX_PINCTRL_PIN(IMX8QXP_COMP_CTL_GPIO_1V8_3V3_GPIORHD),
+	IMX_PINCTRL_PIN(IMX8QXP_MIPI_CSI0_MCLK_OUT),
+	IMX_PINCTRL_PIN(IMX8QXP_MIPI_CSI0_I2C0_SCL),
+	IMX_PINCTRL_PIN(IMX8QXP_MIPI_CSI0_I2C0_SDA),
+	IMX_PINCTRL_PIN(IMX8QXP_MIPI_CSI0_GPIO0_01),
+	IMX_PINCTRL_PIN(IMX8QXP_MIPI_CSI0_GPIO0_00),
+	IMX_PINCTRL_PIN(IMX8QXP_QSPI0A_DATA0),
+	IMX_PINCTRL_PIN(IMX8QXP_QSPI0A_DATA1),
+	IMX_PINCTRL_PIN(IMX8QXP_QSPI0A_DATA2),
+	IMX_PINCTRL_PIN(IMX8QXP_QSPI0A_DATA3),
+	IMX_PINCTRL_PIN(IMX8QXP_QSPI0A_DQS),
+	IMX_PINCTRL_PIN(IMX8QXP_QSPI0A_SS0_B),
+	IMX_PINCTRL_PIN(IMX8QXP_QSPI0A_SS1_B),
+	IMX_PINCTRL_PIN(IMX8QXP_QSPI0A_SCLK),
+	IMX_PINCTRL_PIN(IMX8QXP_COMP_CTL_GPIO_1V8_3V3_QSPI0A),
+	IMX_PINCTRL_PIN(IMX8QXP_QSPI0B_SCLK),
+	IMX_PINCTRL_PIN(IMX8QXP_QSPI0B_DATA0),
+	IMX_PINCTRL_PIN(IMX8QXP_QSPI0B_DATA1),
+	IMX_PINCTRL_PIN(IMX8QXP_QSPI0B_DATA2),
+	IMX_PINCTRL_PIN(IMX8QXP_QSPI0B_DATA3),
+	IMX_PINCTRL_PIN(IMX8QXP_QSPI0B_DQS),
+	IMX_PINCTRL_PIN(IMX8QXP_QSPI0B_SS0_B),
+	IMX_PINCTRL_PIN(IMX8QXP_QSPI0B_SS1_B),
+	IMX_PINCTRL_PIN(IMX8QXP_COMP_CTL_GPIO_1V8_3V3_QSPI0B),
+};
+
+static struct imx_pinctrl_soc_info imx8qxp_pinctrl_info = {
+	.pins = imx8qxp_pinctrl_pads,
+	.npins = ARRAY_SIZE(imx8qxp_pinctrl_pads),
+	.flags = IMX_USE_SCU,
+};
+
+static const struct of_device_id imx8qxp_pinctrl_of_match[] = {
+	{ .compatible = "fsl,imx8qxp-iomuxc", },
+	{ /* sentinel */ }
+};
+
+static int imx8qxp_pinctrl_probe(struct platform_device *pdev)
+{
+	int ret;
+
+	ret = imx_pinctrl_sc_ipc_init(pdev);
+	if (ret)
+		return ret;
+
+	return imx_pinctrl_probe(pdev, &imx8qxp_pinctrl_info);
+}
+
+static struct platform_driver imx8qxp_pinctrl_driver = {
+	.driver = {
+		.name = "imx8qxp-pinctrl",
+		.of_match_table = of_match_ptr(imx8qxp_pinctrl_of_match),
+		.suppress_bind_attrs = true,
+	},
+	.probe = imx8qxp_pinctrl_probe,
+};
+
+static int __init imx8qxp_pinctrl_init(void)
+{
+	return platform_driver_register(&imx8qxp_pinctrl_driver);
+}
+arch_initcall(imx8qxp_pinctrl_init);

drivers/pinctrl/freescale/pinctrl-scu.c

+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ * Copyright 2017-2018 NXP
+ *	Dong Aisheng <aisheng.dong@nxp.com>
+ */
+
+#include <linux/err.h>
+#include <linux/firmware/imx/sci.h>
+#include <linux/of_address.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/platform_device.h>
+
+#include "../core.h"
+#include "pinctrl-imx.h"
+
+enum pad_func_e {
+	IMX_SC_PAD_FUNC_SET = 15,
+	IMX_SC_PAD_FUNC_GET = 16,
+};
+
+struct imx_sc_msg_req_pad_set {
+	struct imx_sc_rpc_msg hdr;
+	u32 val;
+	u16 pad;
+} __packed;
+
+struct imx_sc_msg_req_pad_get {
+	struct imx_sc_rpc_msg hdr;
+	u16 pad;
+} __packed;
+
+struct imx_sc_msg_resp_pad_get {
+	struct imx_sc_rpc_msg hdr;
+	u32 val;
+} __packed;
+
+struct imx_sc_ipc *pinctrl_ipc_handle;
+
+int imx_pinctrl_sc_ipc_init(struct platform_device *pdev)
+{
+	return imx_scu_get_handle(&pinctrl_ipc_handle);
+}
+
+int imx_pinconf_get_scu(struct pinctrl_dev *pctldev, unsigned pin_id,
+			unsigned long *config)
+{
+	struct imx_sc_msg_req_pad_get msg;
+	struct imx_sc_msg_resp_pad_get *resp;
+	struct imx_sc_rpc_msg *hdr = &msg.hdr;
+	int ret;
+
+	hdr->ver = IMX_SC_RPC_VERSION;
+	hdr->svc = IMX_SC_RPC_SVC_PAD;
+	hdr->func = IMX_SC_PAD_FUNC_GET;
+	hdr->size = 2;
+
+	msg.pad = pin_id;
+
+	ret = imx_scu_call_rpc(pinctrl_ipc_handle, &msg, true);
+	if (ret)
+		return ret;
+
+	resp = (struct imx_sc_msg_resp_pad_get *)&msg;
+	*config = resp->val;
+
+	return 0;
+}
+
+int imx_pinconf_set_scu(struct pinctrl_dev *pctldev, unsigned pin_id,
+			unsigned long *configs, unsigned num_configs)
+{
+	struct imx_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev);
+	struct imx_sc_msg_req_pad_set msg;
+	struct imx_sc_rpc_msg *hdr = &msg.hdr;
+	unsigned int mux = configs[0];
+	unsigned int conf = configs[1];
+	unsigned int val;
+	int ret;
+
+	/*
+	 * Set mux and conf together in one IPC call
+	 */
+	WARN_ON(num_configs != 2);
+
+	val = conf | BM_PAD_CTL_IFMUX_ENABLE | BM_PAD_CTL_GP_ENABLE;
+	val |= mux << BP_PAD_CTL_IFMUX;
+
+	hdr->ver = IMX_SC_RPC_VERSION;
+	hdr->svc = IMX_SC_RPC_SVC_PAD;
+	hdr->func = IMX_SC_PAD_FUNC_SET;
+	hdr->size = 3;
+
+	msg.pad = pin_id;
+	msg.val = val;
+
+	ret = imx_scu_call_rpc(pinctrl_ipc_handle, &msg, true);
+
+	dev_dbg(ipctl->dev, "write: pin_id %u config 0x%x val 0x%x\n",
+		pin_id, conf, val);
+
+	return ret;
+}
+
+void imx_pinctrl_parse_pin_scu(struct imx_pinctrl *ipctl,
+			       unsigned int *pin_id, struct imx_pin *pin,
+			       const __be32 **list_p)
+{
+	const struct imx_pinctrl_soc_info *info = ipctl->info;
+	struct imx_pin_scu *pin_scu = &pin->conf.scu;
+	const __be32 *list = *list_p;
+
+	pin->pin = be32_to_cpu(*list++);
+	*pin_id = pin->pin;
+	pin_scu->mux_mode = be32_to_cpu(*list++);
+	pin_scu->config = be32_to_cpu(*list++);
+	*list_p = list;
+
+	dev_dbg(ipctl->dev, "%s: 0x%x 0x%08lx", info->pins[pin->pin].name,
+		pin_scu->mux_mode, pin_scu->config);
+}

drivers/pinctrl/intel/pinctrl-baytrail.c

@@ -705,7 +705,7 @@ static const struct byt_pinctrl_soc_data *byt_soc_data[] = {
 	&byt_score_soc_data,
 	&byt_sus_soc_data,
 	&byt_ncore_soc_data,
-	NULL,
+	NULL
 };
 
 static struct byt_community *byt_get_community(struct byt_gpio *vg,
@@ -1838,8 +1838,7 @@ static int byt_pinctrl_probe(struct platform_device *pdev)
 #ifdef CONFIG_PM_SLEEP
 static int byt_gpio_suspend(struct device *dev)
 {
-	struct platform_device *pdev = to_platform_device(dev);
-	struct byt_gpio *vg = platform_get_drvdata(pdev);
+	struct byt_gpio *vg = dev_get_drvdata(dev);
 	int i;
 
 	for (i = 0; i < vg->soc_data->npins; i++) {
@@ -1867,8 +1866,7 @@ static int byt_gpio_suspend(struct device *dev)
 
 static int byt_gpio_resume(struct device *dev)
 {
-	struct platform_device *pdev = to_platform_device(dev);
-	struct byt_gpio *vg = platform_get_drvdata(pdev);
+	struct byt_gpio *vg = dev_get_drvdata(dev);
 	int i;
 
 	for (i = 0; i < vg->soc_data->npins; i++) {

drivers/pinctrl/intel/pinctrl-broxton.c

@@ -526,7 +526,7 @@ static const struct intel_pinctrl_soc_data *bxt_pinctrl_soc_data[] = {
 	&bxt_west_soc_data,
 	&bxt_southwest_soc_data,
 	&bxt_south_soc_data,
-	NULL,
+	NULL
 };
 
 /* APL */
@@ -990,7 +990,7 @@ static const struct intel_pinctrl_soc_data *apl_pinctrl_soc_data[] = {
 	&apl_northwest_soc_data,
 	&apl_west_soc_data,
 	&apl_southwest_soc_data,
-	NULL,
+	NULL
 };
 
 static const struct acpi_device_id bxt_pinctrl_acpi_match[] = {
@@ -1003,18 +1003,13 @@ MODULE_DEVICE_TABLE(acpi, bxt_pinctrl_acpi_match);
 static const struct platform_device_id bxt_pinctrl_platform_ids[] = {
 	{ "apollolake-pinctrl", (kernel_ulong_t)apl_pinctrl_soc_data },
 	{ "broxton-pinctrl", (kernel_ulong_t)bxt_pinctrl_soc_data },
-	{ },
+	{ }
 };
 
-static int bxt_pinctrl_probe(struct platform_device *pdev)
-{
-	return intel_pinctrl_probe_by_uid(pdev);
-}
-
 static INTEL_PINCTRL_PM_OPS(bxt_pinctrl_pm_ops);
 
 static struct platform_driver bxt_pinctrl_driver = {
-	.probe = bxt_pinctrl_probe,
+	.probe = intel_pinctrl_probe_by_uid,
 	.driver = {
 		.name = "broxton-pinctrl",
 		.acpi_match_table = bxt_pinctrl_acpi_match,

drivers/pinctrl/intel/pinctrl-cannonlake.c

@@ -829,19 +829,14 @@ static const struct intel_pinctrl_soc_data cnllp_soc_data = {
 static const struct acpi_device_id cnl_pinctrl_acpi_match[] = {
 	{ "INT3450", (kernel_ulong_t)&cnlh_soc_data },
 	{ "INT34BB", (kernel_ulong_t)&cnllp_soc_data },
-	{ },
+	{ }
 };
 MODULE_DEVICE_TABLE(acpi, cnl_pinctrl_acpi_match);
 
-static int cnl_pinctrl_probe(struct platform_device *pdev)
-{
-	return intel_pinctrl_probe_by_hid(pdev);
-}
-
 static INTEL_PINCTRL_PM_OPS(cnl_pinctrl_pm_ops);
 
 static struct platform_driver cnl_pinctrl_driver = {
-	.probe = cnl_pinctrl_probe,
+	.probe = intel_pinctrl_probe_by_hid,
 	.driver = {
 		.name = "cannonlake-pinctrl",
 		.acpi_match_table = cnl_pinctrl_acpi_match,

drivers/pinctrl/intel/pinctrl-cedarfork.c

@@ -6,7 +6,7 @@
  * Author: Mika Westerberg <mika.westerberg@linux.intel.com>
  */
 
-#include <linux/acpi.h>
+#include <linux/mod_devicetable.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
 
@@ -330,21 +330,16 @@ static const struct intel_pinctrl_soc_data cdf_soc_data = {
 	.ncommunities = ARRAY_SIZE(cdf_communities),
 };
 
-static int cdf_pinctrl_probe(struct platform_device *pdev)
-{
-	return intel_pinctrl_probe(pdev, &cdf_soc_data);
-}
-
 static INTEL_PINCTRL_PM_OPS(cdf_pinctrl_pm_ops);
 
 static const struct acpi_device_id cdf_pinctrl_acpi_match[] = {
-	{ "INTC3001" },
+	{ "INTC3001", (kernel_ulong_t)&cdf_soc_data },
 	{ }
 };
 MODULE_DEVICE_TABLE(acpi, cdf_pinctrl_acpi_match);
 
 static struct platform_driver cdf_pinctrl_driver = {
-	.probe = cdf_pinctrl_probe,
+	.probe = intel_pinctrl_probe_by_hid,
 	.driver = {
 		.name = "cedarfork-pinctrl",
 		.acpi_match_table = cdf_pinctrl_acpi_match,

drivers/pinctrl/intel/pinctrl-cherryview.c

@@ -846,6 +846,19 @@ static int chv_pinmux_set_mux(struct pinctrl_dev *pctldev,
 	return 0;
 }
 
+static void chv_gpio_clear_triggering(struct chv_pinctrl *pctrl,
+				      unsigned int offset)
+{
+	void __iomem *reg;
+	u32 value;
+
+	reg = chv_padreg(pctrl, offset, CHV_PADCTRL1);
+	value = readl(reg);
+	value &= ~CHV_PADCTRL1_INTWAKECFG_MASK;
+	value &= ~CHV_PADCTRL1_INVRXTX_MASK;
+	chv_writel(value, reg);
+}
+
 static int chv_gpio_request_enable(struct pinctrl_dev *pctldev,
 				   struct pinctrl_gpio_range *range,
 				   unsigned int offset)
@@ -876,11 +889,7 @@ static int chv_gpio_request_enable(struct pinctrl_dev *pctldev,
 		}
 
 		/* Disable interrupt generation */
-		reg = chv_padreg(pctrl, offset, CHV_PADCTRL1);
-		value = readl(reg);
-		value &= ~CHV_PADCTRL1_INTWAKECFG_MASK;
-		value &= ~CHV_PADCTRL1_INVRXTX_MASK;
-		chv_writel(value, reg);
+		chv_gpio_clear_triggering(pctrl, offset);
 
 		reg = chv_padreg(pctrl, offset, CHV_PADCTRL0);
 		value = readl(reg);
@@ -912,14 +921,11 @@ static void chv_gpio_disable_free(struct pinctrl_dev *pctldev,
 {
 	struct chv_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
 	unsigned long flags;
-	void __iomem *reg;
-	u32 value;
 
 	raw_spin_lock_irqsave(&chv_lock, flags);
 
-	reg = chv_padreg(pctrl, offset, CHV_PADCTRL0);
-	value = readl(reg) & ~CHV_PADCTRL0_GPIOEN;
-	chv_writel(value, reg);
+	if (!chv_pad_locked(pctrl, offset))
+		chv_gpio_clear_triggering(pctrl, offset);
 
 	raw_spin_unlock_irqrestore(&chv_lock, flags);
 }
@@ -1744,8 +1750,7 @@ static int chv_pinctrl_remove(struct platform_device *pdev)
 #ifdef CONFIG_PM_SLEEP
 static int chv_pinctrl_suspend_noirq(struct device *dev)
 {
-	struct platform_device *pdev = to_platform_device(dev);
-	struct chv_pinctrl *pctrl = platform_get_drvdata(pdev);
+	struct chv_pinctrl *pctrl = dev_get_drvdata(dev);
 	unsigned long flags;
 	int i;
 
@@ -1778,8 +1783,7 @@ static int chv_pinctrl_suspend_noirq(struct device *dev)
 
 static int chv_pinctrl_resume_noirq(struct device *dev)
 {
-	struct platform_device *pdev = to_platform_device(dev);
-	struct chv_pinctrl *pctrl = platform_get_drvdata(pdev);
+	struct chv_pinctrl *pctrl = dev_get_drvdata(dev);
 	unsigned long flags;
 	int i;
 

drivers/pinctrl/intel/pinctrl-denverton.c

@@ -6,7 +6,7 @@
  * Author: Mika Westerberg <mika.westerberg@linux.intel.com>
  */
 
-#include <linux/acpi.h>
+#include <linux/mod_devicetable.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
 
@@ -257,21 +257,16 @@ static const struct intel_pinctrl_soc_data dnv_soc_data = {
 	.ncommunities = ARRAY_SIZE(dnv_communities),
 };
 
-static int dnv_pinctrl_probe(struct platform_device *pdev)
-{
-	return intel_pinctrl_probe(pdev, &dnv_soc_data);
-}
-
 static INTEL_PINCTRL_PM_OPS(dnv_pinctrl_pm_ops);
 
 static const struct acpi_device_id dnv_pinctrl_acpi_match[] = {
-	{ "INTC3000" },
+	{ "INTC3000", (kernel_ulong_t)&dnv_soc_data },
 	{ }
 };
 MODULE_DEVICE_TABLE(acpi, dnv_pinctrl_acpi_match);
 
 static struct platform_driver dnv_pinctrl_driver = {
-	.probe = dnv_pinctrl_probe,
+	.probe = intel_pinctrl_probe_by_hid,
 	.driver = {
 		.name = "denverton-pinctrl",
 		.acpi_match_table = dnv_pinctrl_acpi_match,

drivers/pinctrl/intel/pinctrl-geminilake.c

@@ -445,7 +445,7 @@ static const struct intel_pinctrl_soc_data *glk_pinctrl_soc_data[] = {
 	&glk_north_soc_data,
 	&glk_audio_soc_data,
 	&glk_scc_soc_data,
-	NULL,
+	NULL
 };
 
 static const struct acpi_device_id glk_pinctrl_acpi_match[] = {

drivers/pinctrl/intel/pinctrl-icelake.c

@@ -403,21 +403,16 @@ static const struct intel_pinctrl_soc_data icllp_soc_data = {
 	.ncommunities = ARRAY_SIZE(icllp_communities),
 };
 
-static int icl_pinctrl_probe(struct platform_device *pdev)
-{
-	return intel_pinctrl_probe(pdev, &icllp_soc_data);
-}
-
 static INTEL_PINCTRL_PM_OPS(icl_pinctrl_pm_ops);
 
 static const struct acpi_device_id icl_pinctrl_acpi_match[] = {
-	{ "INT3455" },
-	{ },
+	{ "INT3455", (kernel_ulong_t)&icllp_soc_data },
+	{ }
 };
 MODULE_DEVICE_TABLE(acpi, icl_pinctrl_acpi_match);
 
 static struct platform_driver icl_pinctrl_driver = {
-	.probe = icl_pinctrl_probe,
+	.probe = intel_pinctrl_probe_by_hid,
 	.driver = {
 		.name = "icelake-pinctrl",
 		.acpi_match_table = icl_pinctrl_acpi_match,

drivers/pinctrl/intel/pinctrl-intel.c

@@ -1301,7 +1301,7 @@ static int intel_pinctrl_pm_init(struct intel_pinctrl *pctrl)
 	return 0;
 }
 
-int intel_pinctrl_probe(struct platform_device *pdev,
+static int intel_pinctrl_probe(struct platform_device *pdev,
 			       const struct intel_pinctrl_soc_data *soc_data)
 {
 	struct intel_pinctrl *pctrl;
@@ -1400,7 +1400,6 @@ int intel_pinctrl_probe(struct platform_device *pdev,
 
 	return 0;
 }
-EXPORT_SYMBOL_GPL(intel_pinctrl_probe);
 
 int intel_pinctrl_probe_by_hid(struct platform_device *pdev)
 {
@@ -1469,8 +1468,7 @@ static bool intel_pinctrl_should_save(struct intel_pinctrl *pctrl, unsigned int
 
 int intel_pinctrl_suspend(struct device *dev)
 {
-	struct platform_device *pdev = to_platform_device(dev);
-	struct intel_pinctrl *pctrl = platform_get_drvdata(pdev);
+	struct intel_pinctrl *pctrl = dev_get_drvdata(dev);
 	struct intel_community_context *communities;
 	struct intel_pad_context *pads;
 	int i;
@@ -1531,8 +1529,7 @@ static void intel_gpio_irq_init(struct intel_pinctrl *pctrl)
 
 int intel_pinctrl_resume(struct device *dev)
 {
-	struct platform_device *pdev = to_platform_device(dev);
-	struct intel_pinctrl *pctrl = platform_get_drvdata(pdev);
+	struct intel_pinctrl *pctrl = dev_get_drvdata(dev);
 	const struct intel_community_context *communities;
 	const struct intel_pad_context *pads;
 	int i;

drivers/pinctrl/intel/pinctrl-intel.h

@@ -173,8 +173,6 @@ struct intel_pinctrl_soc_data {
 	size_t ncommunities;
 };
 
-int intel_pinctrl_probe(struct platform_device *pdev,
-			const struct intel_pinctrl_soc_data *soc_data);
 int intel_pinctrl_probe_by_hid(struct platform_device *pdev);
 int intel_pinctrl_probe_by_uid(struct platform_device *pdev);
 

drivers/pinctrl/intel/pinctrl-lewisburg.c

@@ -6,7 +6,7 @@
  * Author: Mika Westerberg <mika.westerberg@linux.intel.com>
  */
 
-#include <linux/acpi.h>
+#include <linux/mod_devicetable.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
 
@@ -308,21 +308,16 @@ static const struct intel_pinctrl_soc_data lbg_soc_data = {
 	.ncommunities = ARRAY_SIZE(lbg_communities),
 };
 
-static int lbg_pinctrl_probe(struct platform_device *pdev)
-{
-	return intel_pinctrl_probe(pdev, &lbg_soc_data);
-}
-
 static INTEL_PINCTRL_PM_OPS(lbg_pinctrl_pm_ops);
 
 static const struct acpi_device_id lbg_pinctrl_acpi_match[] = {
-	{ "INT3536" },
+	{ "INT3536", (kernel_ulong_t)&lbg_soc_data },
 	{ }
 };
 MODULE_DEVICE_TABLE(acpi, lbg_pinctrl_acpi_match);
 
 static struct platform_driver lbg_pinctrl_driver = {
-	.probe = lbg_pinctrl_probe,
+	.probe = intel_pinctrl_probe_by_hid,
 	.driver = {
 		.name = "lewisburg-pinctrl",
 		.acpi_match_table = lbg_pinctrl_acpi_match,

drivers/pinctrl/intel/pinctrl-merrifield.c

@@ -6,7 +6,7 @@
  * Author: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
  */
 
-#include <linux/bitops.h>
+#include <linux/bits.h>
 #include <linux/err.h>
 #include <linux/io.h>
 #include <linux/module.h>

drivers/pinctrl/intel/pinctrl-sunrisepoint.c

@@ -591,15 +591,10 @@ static const struct acpi_device_id spt_pinctrl_acpi_match[] = {
 };
 MODULE_DEVICE_TABLE(acpi, spt_pinctrl_acpi_match);
 
-static int spt_pinctrl_probe(struct platform_device *pdev)
-{
-	return intel_pinctrl_probe_by_hid(pdev);
-}
-
 static INTEL_PINCTRL_PM_OPS(spt_pinctrl_pm_ops);
 
 static struct platform_driver spt_pinctrl_driver = {
-	.probe = spt_pinctrl_probe,
+	.probe = intel_pinctrl_probe_by_hid,
 	.driver = {
 		.name = "sunrisepoint-pinctrl",
 		.acpi_match_table = spt_pinctrl_acpi_match,

drivers/pinctrl/mediatek/Kconfig

@@ -3,7 +3,7 @@ menu "MediaTek pinctrl drivers"
 
 config EINT_MTK
 	bool "MediaTek External Interrupt Support"
-	depends on PINCTRL_MTK || PINCTRL_MTK_MOORE || COMPILE_TEST
+	depends on PINCTRL_MTK || PINCTRL_MTK_MOORE || PINCTRL_MTK_PARIS || COMPILE_TEST
 	select GPIOLIB
 	select IRQ_DOMAIN
 
@@ -17,7 +17,7 @@ config PINCTRL_MTK
 	select OF_GPIO
 
 config PINCTRL_MTK_MOORE
-	bool "MediaTek Moore Core that implements generic binding"
+	bool
 	depends on OF
 	select GENERIC_PINCONF
 	select GENERIC_PINCTRL_GROUPS
@@ -26,7 +26,7 @@ config PINCTRL_MTK_MOORE
 	select OF_GPIO
 
 config PINCTRL_MTK_PARIS
-	bool "MediaTek Paris Core that implements vendor binding"
+	bool
 	depends on OF
 	select PINMUX
 	select GENERIC_PINCONF
@@ -45,8 +45,14 @@ config PINCTRL_MT2701
 config PINCTRL_MT7623
 	bool "Mediatek MT7623 pin control with generic binding"
 	depends on MACH_MT7623 || COMPILE_TEST
-	depends on PINCTRL_MTK_MOORE
-	default y
+	default MACH_MT7623
+	select PINCTRL_MTK_MOORE
+
+config PINCTRL_MT7629
+	bool "Mediatek MT7629 pin control"
+	depends on MACH_MT7629 || COMPILE_TEST
+	default MACH_MT7629
+	select PINCTRL_MTK_MOORE
 
 config PINCTRL_MT8135
 	bool "Mediatek MT8135 pin control"
@@ -77,11 +83,18 @@ config PINCTRL_MT6765
 	default ARM64 && ARCH_MEDIATEK
 	select PINCTRL_MTK_PARIS
 
+config PINCTRL_MT6797
+	bool "Mediatek MT6797 pin control"
+	depends on OF
+	depends on ARM64 || COMPILE_TEST
+	default ARM64 && ARCH_MEDIATEK
+	select PINCTRL_MTK_PARIS
+
 config PINCTRL_MT7622
 	bool "MediaTek MT7622 pin control"
 	depends on ARM64 || COMPILE_TEST
-	depends on PINCTRL_MTK_MOORE
-	default y
+	default ARM64 && ARCH_MEDIATEK
+	select PINCTRL_MTK_MOORE
 
 config PINCTRL_MT8173
 	bool "Mediatek MT8173 pin control"

drivers/pinctrl/mediatek/Makefile

@@ -11,8 +11,10 @@ obj-$(CONFIG_PINCTRL_MT2712)	+= pinctrl-mt2712.o
 obj-$(CONFIG_PINCTRL_MT8135)	+= pinctrl-mt8135.o
 obj-$(CONFIG_PINCTRL_MT8127)	+= pinctrl-mt8127.o
 obj-$(CONFIG_PINCTRL_MT6765)	+= pinctrl-mt6765.o
+obj-$(CONFIG_PINCTRL_MT6797)	+= pinctrl-mt6797.o
 obj-$(CONFIG_PINCTRL_MT7622)	+= pinctrl-mt7622.o
 obj-$(CONFIG_PINCTRL_MT7623)	+= pinctrl-mt7623.o
+obj-$(CONFIG_PINCTRL_MT7629)	+= pinctrl-mt7629.o
 obj-$(CONFIG_PINCTRL_MT8173)	+= pinctrl-mt8173.o
 obj-$(CONFIG_PINCTRL_MT8183)	+= pinctrl-mt8183.o
 obj-$(CONFIG_PINCTRL_MT6397)	+= pinctrl-mt6397.o

drivers/pinctrl/mediatek/pinctrl-mt6797.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Based on pinctrl-mt6765.c
+ *
+ * Copyright (C) 2018 MediaTek Inc.
+ *
+ * Author: ZH Chen <zh.chen@mediatek.com>
+ *
+ * Copyright (C) Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ *
+ */
+
+#include "pinctrl-mtk-mt6797.h"
+#include "pinctrl-paris.h"
+
+/*
+ * MT6797 have multiple bases to program pin configuration listed as the below:
+ * gpio:0x10005000, iocfg[l]:0x10002000, iocfg[b]:0x10002400,
+ * iocfg[r]:0x10002800, iocfg[t]:0x10002C00.
+ * _i_base could be used to indicate what base the pin should be mapped into.
+ */
+
+static const struct mtk_pin_field_calc mt6797_pin_mode_range[] = {
+	PIN_FIELD(0, 261, 0x300, 0x10, 0, 4),
+};
+
+static const struct mtk_pin_field_calc mt6797_pin_dir_range[] = {
+	PIN_FIELD(0, 261, 0x0, 0x10, 0, 1),
+};
+
+static const struct mtk_pin_field_calc mt6797_pin_di_range[] = {
+	PIN_FIELD(0, 261, 0x200, 0x10, 0, 1),
+};
+
+static const struct mtk_pin_field_calc mt6797_pin_do_range[] = {
+	PIN_FIELD(0, 261, 0x100, 0x10, 0, 1),
+};
+
+static const struct mtk_pin_reg_calc mt6797_reg_cals[PINCTRL_PIN_REG_MAX] = {
+	[PINCTRL_PIN_REG_MODE] = MTK_RANGE(mt6797_pin_mode_range),
+	[PINCTRL_PIN_REG_DIR] = MTK_RANGE(mt6797_pin_dir_range),
+	[PINCTRL_PIN_REG_DI] = MTK_RANGE(mt6797_pin_di_range),
+	[PINCTRL_PIN_REG_DO] = MTK_RANGE(mt6797_pin_do_range),
+};
+
+static const char * const mt6797_pinctrl_register_base_names[] = {
+	"gpio", "iocfgl", "iocfgb", "iocfgr", "iocfgt",
+};
+
+static const struct mtk_pin_soc mt6797_data = {
+	.reg_cal = mt6797_reg_cals,
+	.pins = mtk_pins_mt6797,
+	.npins = ARRAY_SIZE(mtk_pins_mt6797),
+	.ngrps = ARRAY_SIZE(mtk_pins_mt6797),
+	.gpio_m = 0,
+	.base_names = mt6797_pinctrl_register_base_names,
+	.nbase_names = ARRAY_SIZE(mt6797_pinctrl_register_base_names),
+};
+
+static const struct of_device_id mt6797_pinctrl_of_match[] = {
+	{ .compatible = "mediatek,mt6797-pinctrl", },
+	{ }
+};
+
+static int mt6797_pinctrl_probe(struct platform_device *pdev)
+{
+	return mtk_paris_pinctrl_probe(pdev, &mt6797_data);
+}
+
+static struct platform_driver mt6797_pinctrl_driver = {
+	.driver = {
+		.name = "mt6797-pinctrl",
+		.of_match_table = mt6797_pinctrl_of_match,
+	},
+	.probe = mt6797_pinctrl_probe,
+};
+
+static int __init mt6797_pinctrl_init(void)
+{
+	return platform_driver_register(&mt6797_pinctrl_driver);
+}
+arch_initcall(mt6797_pinctrl_init);

drivers/pinctrl/mediatek/pinctrl-paris.c

@@ -419,8 +419,8 @@ static int mtk_pctrl_dt_subnode_to_map(struct pinctrl_dev *pctldev,
 
 	pins = of_find_property(node, "pinmux", NULL);
 	if (!pins) {
-		dev_err(hw->dev, "missing pins property in node %s .\n",
-			node->name);
+		dev_err(hw->dev, "missing pins property in node %pOFn .\n",
+			node);
 		return -EINVAL;
 	}
 

drivers/pinctrl/meson/pinctrl-meson-gxl.c

@@ -239,13 +239,9 @@ static const unsigned int eth_link_led_pins[]	= { GPIOZ_14 };
 static const unsigned int eth_act_led_pins[]	= { GPIOZ_15 };
 
 static const unsigned int tsin_a_d0_pins[]	= { GPIODV_0 };
-static const unsigned int tsin_a_d0_x_pins[]	= { GPIOX_10 };
 static const unsigned int tsin_a_clk_pins[]	= { GPIODV_8 };
-static const unsigned int tsin_a_clk_x_pins[]	= { GPIOX_11 };
 static const unsigned int tsin_a_sop_pins[]	= { GPIODV_9 };
-static const unsigned int tsin_a_sop_x_pins[]	= { GPIOX_8 };
 static const unsigned int tsin_a_d_valid_pins[] = { GPIODV_10 };
-static const unsigned int tsin_a_d_valid_x_pins[] = { GPIOX_9 };
 static const unsigned int tsin_a_fail_pins[]	= { GPIODV_11 };
 static const unsigned int tsin_a_dp_pins[] = {
 	GPIODV_1, GPIODV_2, GPIODV_3, GPIODV_4, GPIODV_5, GPIODV_6, GPIODV_7,
@@ -432,10 +428,6 @@ static struct meson_pmx_group meson_gxl_periphs_groups[] = {
 	GROUP(spi_miso,		5,	2),
 	GROUP(spi_ss0,		5,	1),
 	GROUP(spi_sclk,		5,	0),
-	GROUP(tsin_a_sop_x,	6,	3),
-	GROUP(tsin_a_d_valid_x,	6,	2),
-	GROUP(tsin_a_d0_x,	6,	1),
-	GROUP(tsin_a_clk_x,	6,	0),
 
 	/* Bank Z */
 	GROUP(eth_mdio,		4,	23),
@@ -698,8 +690,8 @@ static const char * const eth_led_groups[] = {
 };
 
 static const char * const tsin_a_groups[] = {
-	"tsin_a_clk", "tsin_a_clk_x", "tsin_a_sop", "tsin_a_sop_x",
-	"tsin_a_d_valid", "tsin_a_d_valid_x", "tsin_a_d0", "tsin_a_d0_x",
+	"tsin_a_clk", "tsin_a_sop",
+	"tsin_a_d_valid", "tsin_a_d0",
 	"tsin_a_dp", "tsin_a_fail",
 };
 

drivers/pinctrl/meson/pinctrl-meson8.c

@@ -506,6 +506,32 @@ static struct meson_pmx_group meson8_cbus_groups[] = {
 	GPIO_GROUP(GPIOZ_12),
 	GPIO_GROUP(GPIOZ_13),
 	GPIO_GROUP(GPIOZ_14),
+	GPIO_GROUP(CARD_0),
+	GPIO_GROUP(CARD_1),
+	GPIO_GROUP(CARD_2),
+	GPIO_GROUP(CARD_3),
+	GPIO_GROUP(CARD_4),
+	GPIO_GROUP(CARD_5),
+	GPIO_GROUP(CARD_6),
+	GPIO_GROUP(BOOT_0),
+	GPIO_GROUP(BOOT_1),
+	GPIO_GROUP(BOOT_2),
+	GPIO_GROUP(BOOT_3),
+	GPIO_GROUP(BOOT_4),
+	GPIO_GROUP(BOOT_5),
+	GPIO_GROUP(BOOT_6),
+	GPIO_GROUP(BOOT_7),
+	GPIO_GROUP(BOOT_8),
+	GPIO_GROUP(BOOT_9),
+	GPIO_GROUP(BOOT_10),
+	GPIO_GROUP(BOOT_11),
+	GPIO_GROUP(BOOT_12),
+	GPIO_GROUP(BOOT_13),
+	GPIO_GROUP(BOOT_14),
+	GPIO_GROUP(BOOT_15),
+	GPIO_GROUP(BOOT_16),
+	GPIO_GROUP(BOOT_17),
+	GPIO_GROUP(BOOT_18),
 
 	/* bank X */
 	GROUP(sd_d0_a,		8,	5),
@@ -774,7 +800,7 @@ static struct meson_pmx_group meson8_aobus_groups[] = {
 	GROUP(hdmi_cec_ao,		0,	17),
 };
 
-static const char * const gpio_groups[] = {
+static const char * const gpio_periphs_groups[] = {
 	"GPIOX_0", "GPIOX_1", "GPIOX_2", "GPIOX_3", "GPIOX_4",
 	"GPIOX_5", "GPIOX_6", "GPIOX_7", "GPIOX_8", "GPIOX_9",
 	"GPIOX_10", "GPIOX_11", "GPIOX_12", "GPIOX_13", "GPIOX_14",
@@ -807,7 +833,9 @@ static const char * const gpio_groups[] = {
 	"BOOT_5", "BOOT_6", "BOOT_7", "BOOT_8", "BOOT_9",
 	"BOOT_10", "BOOT_11", "BOOT_12", "BOOT_13", "BOOT_14",
 	"BOOT_15", "BOOT_16", "BOOT_17", "BOOT_18",
+};
 
+static const char * const gpio_aobus_groups[] = {
 	"GPIOAO_0", "GPIOAO_1", "GPIOAO_2", "GPIOAO_3",
 	"GPIOAO_4", "GPIOAO_5", "GPIOAO_6", "GPIOAO_7",
 	"GPIOAO_8", "GPIOAO_9", "GPIOAO_10", "GPIOAO_11",
@@ -994,7 +1022,7 @@ static const char * const hdmi_cec_ao_groups[] = {
 };
 
 static struct meson_pmx_func meson8_cbus_functions[] = {
-	FUNCTION(gpio),
+	FUNCTION(gpio_periphs),
 	FUNCTION(sd_a),
 	FUNCTION(sdxc_a),
 	FUNCTION(pcm_a),
@@ -1030,6 +1058,7 @@ static struct meson_pmx_func meson8_cbus_functions[] = {
 };
 
 static struct meson_pmx_func meson8_aobus_functions[] = {
+	FUNCTION(gpio_aobus),
 	FUNCTION(uart_ao),
 	FUNCTION(remote),
 	FUNCTION(i2c_slave_ao),

drivers/pinctrl/pinctrl-amd.c

@@ -791,8 +791,7 @@ static bool amd_gpio_should_save(struct amd_gpio *gpio_dev, unsigned int pin)
 
 static int amd_gpio_suspend(struct device *dev)
 {
-	struct platform_device *pdev = to_platform_device(dev);
-	struct amd_gpio *gpio_dev = platform_get_drvdata(pdev);
+	struct amd_gpio *gpio_dev = dev_get_drvdata(dev);
 	struct pinctrl_desc *desc = gpio_dev->pctrl->desc;
 	int i;
 
@@ -810,8 +809,7 @@ static int amd_gpio_suspend(struct device *dev)
 
 static int amd_gpio_resume(struct device *dev)
 {
-	struct platform_device *pdev = to_platform_device(dev);
-	struct amd_gpio *gpio_dev = platform_get_drvdata(pdev);
+	struct amd_gpio *gpio_dev = dev_get_drvdata(dev);
 	struct pinctrl_desc *desc = gpio_dev->pctrl->desc;
 	int i;
 

drivers/pinctrl/qcom/pinctrl-sdm845.c

@@ -1300,6 +1300,7 @@ static const struct of_device_id sdm845_pinctrl_of_match[] = {
 static struct platform_driver sdm845_pinctrl_driver = {
 	.driver = {
 		.name = "sdm845-pinctrl",
+		.pm = &msm_pinctrl_dev_pm_ops,
 		.of_match_table = sdm845_pinctrl_of_match,
 	},
 	.probe = sdm845_pinctrl_probe,