Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull arm-soc power management changes from Olof Johansson:
 "Power management changes here are mostly for the omap platform, but
  also include cpuidle changes for ux500 and suspend/resume code for
  mmp."

* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
  ARM: OMAP2+: WDTIMER integration: fix !PM boot crash, disarm timer after hwmod reset
  ARM: OMAP2/3: hwmod data: Add 32k-sync timer data to hwmod database
  ARM: OMAP4: hwmod_data: Name the common irq for McBSP ports
  ARM: OMAP4: hwmod data: I2C: add flag for context restore
  ARM: OMAP3: hwmod_data: Rename the common irq for McBSP ports
  ARM: OMAP2xxx: hwmod data: add HDQ/1-wire hwmod
  ARM: OMAP3: hwmod data: add HDQ/1-wire hwmod
  ARM: OMAP2+: hwmod data: add HDQ/1-wire hwmod shared data
  ARM: OMAP2+: HDQ1W: add custom reset function
  ARM: OMAP2420: hwmod data: Add MMC hwmod data for 2420
  arm: omap3: clockdomain data: Remove superfluous commas from gfx_sgx_3xxx_wkdeps[]
  ARM: OMAP2+: powerdomain: Get rid off duplicate pwrdm_clkdm_state_switch() API
  ARM: OMAP3: clock data: add clockdomain for HDQ functional clock
  ARM: OMAP3+: dpll: Configure autoidle mode only if it's supported
  ARM: OMAP2+: dmtimer: cleanup iclk usage
  ARM: OMAP4+: Add prm and cm base init function.
  ARM: OMAP2/3: Add idle_st bits for ST_32KSYNC timer to prcm-common header
  ARM: OMAP3: Fix CM register bit masks
  ARM: OMAP: clock: convert AM3517/3505 detection/flags to AM35xx
  ARM: OMAP3: clock data: treat all AM35x devices the same
  ...

arch/arm/Kconfig

@@ -2261,7 +2261,7 @@ source "kernel/power/Kconfig"
 config ARCH_SUSPEND_POSSIBLE
 	depends on !ARCH_S5PC100 && !ARCH_TEGRA
 	depends on CPU_ARM920T || CPU_ARM926T || CPU_SA1100 || \
-		CPU_V6 || CPU_V6K || CPU_V7 || CPU_XSC3 || CPU_XSCALE
+		CPU_V6 || CPU_V6K || CPU_V7 || CPU_XSC3 || CPU_XSCALE || CPU_MOHAWK
 	def_bool y
 
 config ARM_CPU_SUSPEND

arch/arm/mach-mmp/Makefile

@@ -9,6 +9,11 @@ obj-$(CONFIG_CPU_PXA168)	+= pxa168.o
 obj-$(CONFIG_CPU_PXA910)	+= pxa910.o
 obj-$(CONFIG_CPU_MMP2)		+= mmp2.o sram.o
 
+ifeq ($(CONFIG_PM),y)
+obj-$(CONFIG_CPU_PXA910)	+= pm-pxa910.o
+obj-$(CONFIG_CPU_MMP2)		+= pm-mmp2.o
+endif
+
 # board support
 obj-$(CONFIG_MACH_ASPENITE)	+= aspenite.o
 obj-$(CONFIG_MACH_ZYLONITE2)	+= aspenite.o

arch/arm/mach-mmp/include/mach/addr-map.h

@@ -31,4 +31,16 @@
 #define SMC_CS1_PHYS_BASE	0x90000000
 #define SMC_CS1_PHYS_SIZE	0x10000000
 
+#define APMU_VIRT_BASE		(AXI_VIRT_BASE + 0x82800)
+#define APMU_REG(x)		(APMU_VIRT_BASE + (x))
+
+#define APBC_VIRT_BASE		(APB_VIRT_BASE + 0x015000)
+#define APBC_REG(x)		(APBC_VIRT_BASE + (x))
+
+#define MPMU_VIRT_BASE		(APB_VIRT_BASE + 0x50000)
+#define MPMU_REG(x)		(MPMU_VIRT_BASE + (x))
+
+#define CIU_VIRT_BASE		(AXI_VIRT_BASE + 0x82c00)
+#define CIU_REG(x)		(CIU_VIRT_BASE + (x))
+
 #endif /* __ASM_MACH_ADDR_MAP_H */

arch/arm/mach-mmp/include/mach/pm-mmp2.h

+/*
+ * MMP2 Power Management Routines
+ *
+ * This software program is licensed subject to the GNU General Public License
+ * (GPL).Version 2,June 1991, available at http://www.fsf.org/copyleft/gpl.html
+ *
+ * (C) Copyright 2010 Marvell International Ltd.
+ * All Rights Reserved
+ */
+
+#ifndef __MMP2_PM_H__
+#define __MMP2_PM_H__
+
+#include <mach/addr-map.h>
+
+#define APMU_PJ_IDLE_CFG			APMU_REG(0x018)
+#define APMU_PJ_IDLE_CFG_PJ_IDLE		(1 << 1)
+#define APMU_PJ_IDLE_CFG_PJ_PWRDWN		(1 << 5)
+#define APMU_PJ_IDLE_CFG_PWR_SW(x)		((x) << 16)
+#define APMU_PJ_IDLE_CFG_L2_PWR_SW		(1 << 19)
+#define APMU_PJ_IDLE_CFG_ISO_MODE_CNTRL_MASK	(3 << 28)
+
+#define APMU_SRAM_PWR_DWN			APMU_REG(0x08c)
+
+#define MPMU_SCCR				MPMU_REG(0x038)
+#define MPMU_PCR_PJ				MPMU_REG(0x1000)
+#define MPMU_PCR_PJ_AXISD			(1 << 31)
+#define MPMU_PCR_PJ_SLPEN			(1 << 29)
+#define MPMU_PCR_PJ_SPSD			(1 << 28)
+#define MPMU_PCR_PJ_DDRCORSD			(1 << 27)
+#define MPMU_PCR_PJ_APBSD			(1 << 26)
+#define MPMU_PCR_PJ_INTCLR			(1 << 24)
+#define MPMU_PCR_PJ_SLPWP0			(1 << 23)
+#define MPMU_PCR_PJ_SLPWP1			(1 << 22)
+#define MPMU_PCR_PJ_SLPWP2			(1 << 21)
+#define MPMU_PCR_PJ_SLPWP3			(1 << 20)
+#define MPMU_PCR_PJ_VCTCXOSD			(1 << 19)
+#define MPMU_PCR_PJ_SLPWP4			(1 << 18)
+#define MPMU_PCR_PJ_SLPWP5			(1 << 17)
+#define MPMU_PCR_PJ_SLPWP6			(1 << 16)
+#define MPMU_PCR_PJ_SLPWP7			(1 << 15)
+
+#define MPMU_PLL2_CTRL1				MPMU_REG(0x0414)
+#define MPMU_CGR_PJ				MPMU_REG(0x1024)
+#define MPMU_WUCRM_PJ				MPMU_REG(0x104c)
+#define MPMU_WUCRM_PJ_WAKEUP(x)			(1 << (x))
+#define MPMU_WUCRM_PJ_RTC_ALARM			(1 << 17)
+
+enum {
+	POWER_MODE_ACTIVE = 0,
+	POWER_MODE_CORE_INTIDLE,
+	POWER_MODE_CORE_EXTIDLE,
+	POWER_MODE_APPS_IDLE,
+	POWER_MODE_APPS_SLEEP,
+	POWER_MODE_CHIP_SLEEP,
+	POWER_MODE_SYS_SLEEP,
+};
+
+extern void mmp2_pm_enter_lowpower_mode(int state);
+extern int mmp2_set_wake(struct irq_data *d, unsigned int on);
+#endif

arch/arm/mach-mmp/include/mach/pm-pxa910.h

+/*
+ * PXA910 Power Management Routines
+ *
+ * This software program is licensed subject to the GNU General Public License
+ * (GPL).Version 2,June 1991, available at http://www.fsf.org/copyleft/gpl.html
+ *
+ * (C) Copyright 2009 Marvell International Ltd.
+ * All Rights Reserved
+ */
+
+#ifndef __PXA910_PM_H__
+#define __PXA910_PM_H__
+
+#define APMU_MOH_IDLE_CFG			APMU_REG(0x0018)
+#define APMU_MOH_IDLE_CFG_MOH_IDLE		(1 << 1)
+#define APMU_MOH_IDLE_CFG_MOH_PWRDWN		(1 << 5)
+#define APMU_MOH_IDLE_CFG_MOH_SRAM_PWRDWN	(1 << 6)
+#define APMU_MOH_IDLE_CFG_MOH_PWR_SW(x)		(((x) & 0x3) << 16)
+#define APMU_MOH_IDLE_CFG_MOH_L2_PWR_SW(x)	(((x) & 0x3) << 18)
+#define APMU_MOH_IDLE_CFG_MOH_DIS_MC_SW_REQ	(1 << 21)
+#define APMU_MOH_IDLE_CFG_MOH_MC_WAKE_EN	(1 << 20)
+
+#define APMU_SQU_CLK_GATE_CTRL			APMU_REG(0x001c)
+#define APMU_MC_HW_SLP_TYPE			APMU_REG(0x00b0)
+
+#define MPMU_FCCR				MPMU_REG(0x0008)
+#define MPMU_APCR				MPMU_REG(0x1000)
+#define MPMU_APCR_AXISD				(1 << 31)
+#define MPMU_APCR_DSPSD				(1 << 30)
+#define MPMU_APCR_SLPEN				(1 << 29)
+#define MPMU_APCR_DTCMSD			(1 << 28)
+#define MPMU_APCR_DDRCORSD			(1 << 27)
+#define MPMU_APCR_APBSD				(1 << 26)
+#define MPMU_APCR_BBSD				(1 << 25)
+#define MPMU_APCR_SLPWP0			(1 << 23)
+#define MPMU_APCR_SLPWP1			(1 << 22)
+#define MPMU_APCR_SLPWP2			(1 << 21)
+#define MPMU_APCR_SLPWP3			(1 << 20)
+#define MPMU_APCR_VCTCXOSD			(1 << 19)
+#define MPMU_APCR_SLPWP4			(1 << 18)
+#define MPMU_APCR_SLPWP5			(1 << 17)
+#define MPMU_APCR_SLPWP6			(1 << 16)
+#define MPMU_APCR_SLPWP7			(1 << 15)
+#define MPMU_APCR_MSASLPEN			(1 << 14)
+#define MPMU_APCR_STBYEN			(1 << 13)
+
+#define MPMU_AWUCRM				MPMU_REG(0x104c)
+#define MPMU_AWUCRM_AP_ASYNC_INT		(1 << 25)
+#define MPMU_AWUCRM_AP_FULL_IDLE		(1 << 24)
+#define MPMU_AWUCRM_SDH1			(1 << 23)
+#define MPMU_AWUCRM_SDH2			(1 << 22)
+#define MPMU_AWUCRM_KEYPRESS			(1 << 21)
+#define MPMU_AWUCRM_TRACKBALL			(1 << 20)
+#define MPMU_AWUCRM_NEWROTARY			(1 << 19)
+#define MPMU_AWUCRM_RTC_ALARM			(1 << 17)
+#define MPMU_AWUCRM_AP2_TIMER_3			(1 << 13)
+#define MPMU_AWUCRM_AP2_TIMER_2			(1 << 12)
+#define MPMU_AWUCRM_AP2_TIMER_1			(1 << 11)
+#define MPMU_AWUCRM_AP1_TIMER_3			(1 << 10)
+#define MPMU_AWUCRM_AP1_TIMER_2			(1 << 9)
+#define MPMU_AWUCRM_AP1_TIMER_1			(1 << 8)
+#define MPMU_AWUCRM_WAKEUP(x)			(1 << ((x) & 0x7))
+
+enum {
+	POWER_MODE_ACTIVE = 0,
+	POWER_MODE_CORE_INTIDLE,
+	POWER_MODE_CORE_EXTIDLE,
+	POWER_MODE_APPS_IDLE,
+	POWER_MODE_APPS_SLEEP,
+	POWER_MODE_SYS_SLEEP,
+	POWER_MODE_HIBERNATE,
+	POWER_MODE_UDR,
+};
+
+extern int pxa910_set_wake(struct irq_data *data, unsigned int on);
+
+#endif

arch/arm/mach-mmp/include/mach/regs-apbc.h

@@ -13,9 +13,6 @@
 
 #include <mach/addr-map.h>
 
-#define APBC_VIRT_BASE	(APB_VIRT_BASE + 0x015000)
-#define APBC_REG(x)	(APBC_VIRT_BASE + (x))
-
 /*
  * APB clock register offsets for PXA168
  */

arch/arm/mach-mmp/include/mach/regs-apmu.h

@@ -13,9 +13,6 @@
 
 #include <mach/addr-map.h>
 
-#define APMU_VIRT_BASE	(AXI_VIRT_BASE + 0x82800)
-#define APMU_REG(x)	(APMU_VIRT_BASE + (x))
-
 /* Clock Reset Control */
 #define APMU_IRE	APMU_REG(0x048)
 #define APMU_LCD	APMU_REG(0x04c)

arch/arm/mach-mmp/irq.c

@@ -23,6 +23,13 @@
 
 #include <mach/irqs.h>
 
+#ifdef CONFIG_CPU_MMP2
+#include <mach/pm-mmp2.h>
+#endif
+#ifdef CONFIG_CPU_PXA910
+#include <mach/pm-pxa910.h>
+#endif
+
 #include "common.h"
 
 #define MAX_ICU_NR		16
@@ -209,6 +216,9 @@ void __init icu_init_irq(void)
 		set_irq_flags(irq, IRQF_VALID);
 	}
 	irq_set_default_host(icu_data[0].domain);
+#ifdef CONFIG_CPU_PXA910
+	icu_irq_chip.irq_set_wake = pxa910_set_wake;
+#endif
 }
 
 /* MMP2 (ARMv7) */
@@ -305,6 +315,9 @@ void __init mmp2_init_icu(void)
 		set_irq_flags(irq, IRQF_VALID);
 	}
 	irq_set_default_host(icu_data[0].domain);
+#ifdef CONFIG_CPU_MMP2
+	icu_irq_chip.irq_set_wake = mmp2_set_wake;
+#endif
 }
 
 #ifdef CONFIG_OF

arch/arm/mach-mmp/pm-mmp2.c

+/*
+ * MMP2 Power Management Routines
+ *
+ * This software program is licensed subject to the GNU General Public License
+ * (GPL).Version 2,June 1991, available at http://www.fsf.org/copyleft/gpl.html
+ *
+ * (C) Copyright 2012 Marvell International Ltd.
+ * All Rights Reserved
+ */
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/time.h>
+#include <linux/delay.h>
+#include <linux/suspend.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <asm/mach-types.h>
+#include <mach/hardware.h>
+#include <mach/cputype.h>
+#include <mach/addr-map.h>
+#include <mach/pm-mmp2.h>
+#include <mach/regs-icu.h>
+#include <mach/irqs.h>
+
+int mmp2_set_wake(struct irq_data *d, unsigned int on)
+{
+	int irq = d->irq;
+	struct irq_desc *desc = irq_to_desc(irq);
+	unsigned long data = 0;
+
+	if (unlikely(irq >= nr_irqs)) {
+		pr_err("IRQ nubmers are out of boundary!\n");
+		return -EINVAL;
+	}
+
+	if (on) {
+		if (desc->action)
+			desc->action->flags |= IRQF_NO_SUSPEND;
+	} else {
+		if (desc->action)
+			desc->action->flags &= ~IRQF_NO_SUSPEND;
+	}
+
+	/* enable wakeup sources */
+	switch (irq) {
+	case IRQ_MMP2_RTC:
+	case IRQ_MMP2_RTC_ALARM:
+		data = MPMU_WUCRM_PJ_WAKEUP(4) | MPMU_WUCRM_PJ_RTC_ALARM;
+		break;
+	case IRQ_MMP2_PMIC:
+		data = MPMU_WUCRM_PJ_WAKEUP(7);
+		break;
+	case IRQ_MMP2_MMC2:
+		/* mmc use WAKEUP2, same as GPIO wakeup source */
+		data = MPMU_WUCRM_PJ_WAKEUP(2);
+		break;
+	}
+	if (on) {
+		if (data) {
+			data |= __raw_readl(MPMU_WUCRM_PJ);
+			__raw_writel(data, MPMU_WUCRM_PJ);
+		}
+	} else {
+		if (data) {
+			data = ~data & __raw_readl(MPMU_WUCRM_PJ);
+			__raw_writel(data, MPMU_WUCRM_PJ);
+		}
+	}
+	return 0;
+}
+
+static void pm_scu_clk_disable(void)
+{
+	unsigned int val;
+
+	/* close AXI fabric clock gate */
+	__raw_writel(0x0, CIU_REG(0x64));
+	__raw_writel(0x0, CIU_REG(0x68));
+
+	/* close MCB master clock gate */
+	val = __raw_readl(CIU_REG(0x1c));
+	val |= 0xf0;
+	__raw_writel(val, CIU_REG(0x1c));
+
+	return ;
+}
+
+static void pm_scu_clk_enable(void)
+{
+	unsigned int val;
+
+	/* open AXI fabric clock gate */
+	__raw_writel(0x03003003, CIU_REG(0x64));
+	__raw_writel(0x00303030, CIU_REG(0x68));
+
+	/* open MCB master clock gate */
+	val = __raw_readl(CIU_REG(0x1c));
+	val &= ~(0xf0);
+	__raw_writel(val, CIU_REG(0x1c));
+
+	return ;
+}
+
+static void pm_mpmu_clk_disable(void)
+{
+	/*
+	 * disable clocks in MPMU_CGR_PJ register
+	 * except clock for APMU_PLL1, APMU_PLL1_2 and AP_26M
+	 */
+	__raw_writel(0x0000a010, MPMU_CGR_PJ);
+}
+
+static void pm_mpmu_clk_enable(void)
+{
+	unsigned int val;
+
+	__raw_writel(0xdffefffe, MPMU_CGR_PJ);
+	val = __raw_readl(MPMU_PLL2_CTRL1);
+	val |= (1 << 29);
+	__raw_writel(val, MPMU_PLL2_CTRL1);
+
+	return ;
+}
+
+void mmp2_pm_enter_lowpower_mode(int state)
+{
+	uint32_t idle_cfg, apcr;
+
+	idle_cfg = __raw_readl(APMU_PJ_IDLE_CFG);
+	apcr = __raw_readl(MPMU_PCR_PJ);
+	apcr &= ~(MPMU_PCR_PJ_SLPEN | MPMU_PCR_PJ_DDRCORSD | MPMU_PCR_PJ_APBSD
+		 | MPMU_PCR_PJ_AXISD | MPMU_PCR_PJ_VCTCXOSD | (1 << 13));
+	idle_cfg &= ~APMU_PJ_IDLE_CFG_PJ_IDLE;
+
+	switch (state) {
+	case POWER_MODE_SYS_SLEEP:
+		apcr |= MPMU_PCR_PJ_SLPEN;		/* set the SLPEN bit */
+		apcr |= MPMU_PCR_PJ_VCTCXOSD;		/* set VCTCXOSD */
+		/* fall through */
+	case POWER_MODE_CHIP_SLEEP:
+		apcr |= MPMU_PCR_PJ_SLPEN;
+		/* fall through */
+	case POWER_MODE_APPS_SLEEP:
+		apcr |= MPMU_PCR_PJ_APBSD;		/* set APBSD */
+		/* fall through */
+	case POWER_MODE_APPS_IDLE:
+		apcr |= MPMU_PCR_PJ_AXISD;		/* set AXISDD bit */
+		apcr |= MPMU_PCR_PJ_DDRCORSD;		/* set DDRCORSD bit */
+		idle_cfg |= APMU_PJ_IDLE_CFG_PJ_PWRDWN;	/* PJ power down */
+		apcr |= MPMU_PCR_PJ_SPSD;
+		/* fall through */
+	case POWER_MODE_CORE_EXTIDLE:
+		idle_cfg |= APMU_PJ_IDLE_CFG_PJ_IDLE;	/* set the IDLE bit */
+		idle_cfg &= ~APMU_PJ_IDLE_CFG_ISO_MODE_CNTRL_MASK;
+		idle_cfg |= APMU_PJ_IDLE_CFG_PWR_SW(3)
+			| APMU_PJ_IDLE_CFG_L2_PWR_SW;
+		break;
+	case POWER_MODE_CORE_INTIDLE:
+		apcr &= ~MPMU_PCR_PJ_SPSD;
+		break;
+	}
+
+	/* set reserve bits */
+	apcr |= (1 << 30) | (1 << 25);
+
+	/* finally write the registers back */
+	__raw_writel(idle_cfg, APMU_PJ_IDLE_CFG);
+	__raw_writel(apcr, MPMU_PCR_PJ);	/* 0xfe086000 */
+}
+
+static int mmp2_pm_enter(suspend_state_t state)
+{
+	int temp;
+
+	temp = __raw_readl(MMP2_ICU_INT4_MASK);
+	if (temp & (1 << 1)) {
+		printk(KERN_ERR "%s: PMIC interrupt is handling\n", __func__);
+		return -EAGAIN;
+	}
+
+	temp = __raw_readl(APMU_SRAM_PWR_DWN);
+	temp |= ((1 << 19) | (1 << 18));
+	__raw_writel(temp, APMU_SRAM_PWR_DWN);
+	pm_mpmu_clk_disable();
+	pm_scu_clk_disable();
+
+	printk(KERN_INFO "%s: before suspend\n", __func__);
+	cpu_do_idle();
+	printk(KERN_INFO "%s: after suspend\n", __func__);
+
+	pm_mpmu_clk_enable();		/* enable clocks in MPMU */
+	pm_scu_clk_enable();		/* enable clocks in SCU */
+
+	return 0;
+}
+
+/*
+ * Called after processes are frozen, but before we shut down devices.
+ */
+static int mmp2_pm_prepare(void)
+{
+	mmp2_pm_enter_lowpower_mode(POWER_MODE_SYS_SLEEP);
+
+	return 0;
+}
+
+/*
+ * Called after devices are re-setup, but before processes are thawed.
+ */
+static void mmp2_pm_finish(void)
+{
+	mmp2_pm_enter_lowpower_mode(POWER_MODE_CORE_INTIDLE);
+}
+
+static int mmp2_pm_valid(suspend_state_t state)
+{
+	return ((state == PM_SUSPEND_STANDBY) || (state == PM_SUSPEND_MEM));
+}
+
+/*
+ * Set to PM_DISK_FIRMWARE so we can quickly veto suspend-to-disk.
+ */
+static const struct platform_suspend_ops mmp2_pm_ops = {
+	.valid		= mmp2_pm_valid,
+	.prepare	= mmp2_pm_prepare,
+	.enter		= mmp2_pm_enter,
+	.finish		= mmp2_pm_finish,
+};
+
+static int __init mmp2_pm_init(void)
+{
+	uint32_t apcr;
+
+	if (!cpu_is_mmp2())
+		return -EIO;
+
+	suspend_set_ops(&mmp2_pm_ops);
+
+	/*
+	 * Set bit 0, Slow clock Select 32K clock input instead of VCXO
+	 * VCXO is chosen by default, which would be disabled in suspend
+	 */
+	__raw_writel(0x5, MPMU_SCCR);
+
+	/*
+	 * Clear bit 23 of CIU_CPU_CONF
+	 * direct PJ4 to DDR access through Memory Controller slow queue
+	 * fast queue has issue and cause lcd will flick
+	 */
+	__raw_writel(__raw_readl(CIU_REG(0x8)) & ~(0x1 << 23), CIU_REG(0x8));
+
+	/* Clear default low power control bit */
+	apcr = __raw_readl(MPMU_PCR_PJ);
+	apcr &= ~(MPMU_PCR_PJ_SLPEN | MPMU_PCR_PJ_DDRCORSD
+			| MPMU_PCR_PJ_APBSD | MPMU_PCR_PJ_AXISD | 1 << 13);
+	__raw_writel(apcr, MPMU_PCR_PJ);
+
+	return 0;
+}
+
+late_initcall(mmp2_pm_init);

arch/arm/mach-mmp/pm-pxa910.c

+/*
+ * PXA910 Power Management Routines
+ *
+ * This software program is licensed subject to the GNU General Public License
+ * (GPL).Version 2,June 1991, available at http://www.fsf.org/copyleft/gpl.html
+ *
+ * (C) Copyright 2009 Marvell International Ltd.
+ * All Rights Reserved
+ */
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/time.h>
+#include <linux/delay.h>
+#include <linux/suspend.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <asm/mach-types.h>
+#include <mach/hardware.h>
+#include <mach/cputype.h>
+#include <mach/addr-map.h>
+#include <mach/pm-pxa910.h>
+#include <mach/regs-icu.h>
+#include <mach/irqs.h>
+
+int pxa910_set_wake(struct irq_data *data, unsigned int on)
+{
+	int irq = data->irq;
+	struct irq_desc *desc = irq_to_desc(data->irq);
+	uint32_t awucrm = 0, apcr = 0;
+
+	if (unlikely(irq >= nr_irqs)) {
+		pr_err("IRQ nubmers are out of boundary!\n");
+		return -EINVAL;
+	}
+
+	if (on) {
+		if (desc->action)
+			desc->action->flags |= IRQF_NO_SUSPEND;
+	} else {
+		if (desc->action)
+			desc->action->flags &= ~IRQF_NO_SUSPEND;
+	}
+
+	/* setting wakeup sources */
+	switch (irq) {
+	/* wakeup line 2 */
+	case IRQ_PXA910_AP_GPIO:
+		awucrm = MPMU_AWUCRM_WAKEUP(2);
+		apcr |= MPMU_APCR_SLPWP2;
+		break;
+	/* wakeup line 3 */
+	case IRQ_PXA910_KEYPAD:
+		awucrm = MPMU_AWUCRM_WAKEUP(3) | MPMU_AWUCRM_KEYPRESS;
+		apcr |= MPMU_APCR_SLPWP3;
+		break;
+	case IRQ_PXA910_ROTARY:
+		awucrm = MPMU_AWUCRM_WAKEUP(3) | MPMU_AWUCRM_NEWROTARY;
+		apcr |= MPMU_APCR_SLPWP3;
+		break;
+	case IRQ_PXA910_TRACKBALL:
+		awucrm = MPMU_AWUCRM_WAKEUP(3) | MPMU_AWUCRM_TRACKBALL;
+		apcr |= MPMU_APCR_SLPWP3;
+		break;
+	/* wakeup line 4 */
+	case IRQ_PXA910_AP1_TIMER1:
+		awucrm = MPMU_AWUCRM_WAKEUP(4) | MPMU_AWUCRM_AP1_TIMER_1;
+		apcr |= MPMU_APCR_SLPWP4;
+		break;
+	case IRQ_PXA910_AP1_TIMER2:
+		awucrm = MPMU_AWUCRM_WAKEUP(4) | MPMU_AWUCRM_AP1_TIMER_2;
+		apcr |= MPMU_APCR_SLPWP4;
+		break;
+	case IRQ_PXA910_AP1_TIMER3:
+		awucrm = MPMU_AWUCRM_WAKEUP(4) | MPMU_AWUCRM_AP1_TIMER_3;
+		apcr |= MPMU_APCR_SLPWP4;
+		break;
+	case IRQ_PXA910_AP2_TIMER1:
+		awucrm = MPMU_AWUCRM_WAKEUP(4) | MPMU_AWUCRM_AP2_TIMER_1;
+		apcr |= MPMU_APCR_SLPWP4;
+		break;
+	case IRQ_PXA910_AP2_TIMER2:
+		awucrm = MPMU_AWUCRM_WAKEUP(4) | MPMU_AWUCRM_AP2_TIMER_2;
+		apcr |= MPMU_APCR_SLPWP4;
+		break;
+	case IRQ_PXA910_AP2_TIMER3:
+		awucrm = MPMU_AWUCRM_WAKEUP(4) | MPMU_AWUCRM_AP2_TIMER_3;
+		apcr |= MPMU_APCR_SLPWP4;
+		break;
+	case IRQ_PXA910_RTC_ALARM:
+		awucrm = MPMU_AWUCRM_WAKEUP(4) | MPMU_AWUCRM_RTC_ALARM;
+		apcr |= MPMU_APCR_SLPWP4;
+		break;
+	/* wakeup line 5 */
+	case IRQ_PXA910_USB1:
+	case IRQ_PXA910_USB2:
+		awucrm = MPMU_AWUCRM_WAKEUP(5);
+		apcr |= MPMU_APCR_SLPWP5;
+		break;
+	/* wakeup line 6 */
+	case IRQ_PXA910_MMC:
+		awucrm = MPMU_AWUCRM_WAKEUP(6)
+			| MPMU_AWUCRM_SDH1
+			| MPMU_AWUCRM_SDH2;
+		apcr |= MPMU_APCR_SLPWP6;
+		break;
+	/* wakeup line 7 */
+	case IRQ_PXA910_PMIC_INT:
+		awucrm = MPMU_AWUCRM_WAKEUP(7);
+		apcr |= MPMU_APCR_SLPWP7;
+		break;
+	default:
+		if (irq >= IRQ_GPIO_START && irq < IRQ_BOARD_START) {
+			awucrm = MPMU_AWUCRM_WAKEUP(2);
+			apcr |= MPMU_APCR_SLPWP2;
+		} else
+			printk(KERN_ERR "Error: no defined wake up source irq: %d\n",
+				irq);
+	}
+
+	if (on) {
+		if (awucrm) {
+			awucrm |= __raw_readl(MPMU_AWUCRM);
+			__raw_writel(awucrm, MPMU_AWUCRM);
+		}
+		if (apcr) {
+			apcr = ~apcr & __raw_readl(MPMU_APCR);
+			__raw_writel(apcr, MPMU_APCR);
+		}
+	} else {
+		if (awucrm) {
+			awucrm = ~awucrm & __raw_readl(MPMU_AWUCRM);
+			__raw_writel(awucrm, MPMU_AWUCRM);
+		}
+		if (apcr) {
+			apcr |= __raw_readl(MPMU_APCR);
+			__raw_writel(apcr, MPMU_APCR);
+		}
+	}
+	return 0;
+}
+
+void pxa910_pm_enter_lowpower_mode(int state)
+{
+	uint32_t idle_cfg, apcr;
+
+	idle_cfg = __raw_readl(APMU_MOH_IDLE_CFG);
+	apcr = __raw_readl(MPMU_APCR);
+
+	apcr &= ~(MPMU_APCR_DDRCORSD | MPMU_APCR_APBSD | MPMU_APCR_AXISD
+		| MPMU_APCR_VCTCXOSD | MPMU_APCR_STBYEN);
+	idle_cfg &= ~(APMU_MOH_IDLE_CFG_MOH_IDLE
+		| APMU_MOH_IDLE_CFG_MOH_PWRDWN);
+
+	switch (state) {
+	case POWER_MODE_UDR:
+		/* only shutdown APB in UDR */
+		apcr |= MPMU_APCR_STBYEN | MPMU_APCR_APBSD;
+		/* fall through */
+	case POWER_MODE_SYS_SLEEP:
+		apcr |= MPMU_APCR_SLPEN;		/* set the SLPEN bit */
+		apcr |= MPMU_APCR_VCTCXOSD;		/* set VCTCXOSD */
+		/* fall through */
+	case POWER_MODE_APPS_SLEEP:
+		apcr |= MPMU_APCR_DDRCORSD;		/* set DDRCORSD */
+		/* fall through */
+	case POWER_MODE_APPS_IDLE:
+		apcr |= MPMU_APCR_AXISD;		/* set AXISDD bit */
+		/* fall through */
+	case POWER_MODE_CORE_EXTIDLE:
+		idle_cfg |= APMU_MOH_IDLE_CFG_MOH_IDLE;
+		idle_cfg |= APMU_MOH_IDLE_CFG_MOH_PWRDWN;
+		idle_cfg |= APMU_MOH_IDLE_CFG_MOH_PWR_SW(3)
+			| APMU_MOH_IDLE_CFG_MOH_L2_PWR_SW(3);
+		/* fall through */
+	case POWER_MODE_CORE_INTIDLE:
+		break;
+	}
+
+	/* program the memory controller hardware sleep type and auto wakeup */
+	idle_cfg |= APMU_MOH_IDLE_CFG_MOH_DIS_MC_SW_REQ;
+	idle_cfg |= APMU_MOH_IDLE_CFG_MOH_MC_WAKE_EN;
+	__raw_writel(0x0, APMU_MC_HW_SLP_TYPE);		/* auto refresh */
+
+	/* set DSPSD, DTCMSD, BBSD, MSASLPEN */
+	apcr |= MPMU_APCR_DSPSD | MPMU_APCR_DTCMSD | MPMU_APCR_BBSD
+		| MPMU_APCR_MSASLPEN;
+
+	/*always set SLEPEN bit mainly for MSA*/
+	apcr |= MPMU_APCR_SLPEN;
+
+	/* finally write the registers back */
+	__raw_writel(idle_cfg, APMU_MOH_IDLE_CFG);
+	__raw_writel(apcr, MPMU_APCR);
+
+}
+
+static int pxa910_pm_enter(suspend_state_t state)
+{
+	unsigned int idle_cfg, reg = 0;
+
+	/*pmic thread not completed,exit;otherwise system can't be waked up*/
+	reg = __raw_readl(ICU_INT_CONF(IRQ_PXA910_PMIC_INT));
+	if ((reg & 0x3) == 0)
+		return -EAGAIN;
+
+	idle_cfg = __raw_readl(APMU_MOH_IDLE_CFG);
+	idle_cfg |= APMU_MOH_IDLE_CFG_MOH_PWRDWN
+		| APMU_MOH_IDLE_CFG_MOH_SRAM_PWRDWN;
+	__raw_writel(idle_cfg, APMU_MOH_IDLE_CFG);
+
+	/* disable L2 */
+	outer_disable();
+	/* wait for l2 idle */
+	while (!(readl(CIU_REG(0x8)) & (1 << 16)))
+		udelay(1);
+
+	cpu_do_idle();
+
+	/* enable L2 */
+	outer_resume();
+	/* wait for l2 idle */
+	while (!(readl(CIU_REG(0x8)) & (1 << 16)))
+		udelay(1);
+
+	idle_cfg = __raw_readl(APMU_MOH_IDLE_CFG);
+	idle_cfg &= ~(APMU_MOH_IDLE_CFG_MOH_PWRDWN
+		| APMU_MOH_IDLE_CFG_MOH_SRAM_PWRDWN);
+	__raw_writel(idle_cfg, APMU_MOH_IDLE_CFG);
+
+	return 0;
+}
+
+/*
+ * Called after processes are frozen, but before we shut down devices.
+ */
+static int pxa910_pm_prepare(void)
+{
+	pxa910_pm_enter_lowpower_mode(POWER_MODE_UDR);
+	return 0;
+}
+
+/*
+ * Called after devices are re-setup, but before processes are thawed.
+ */
+static void pxa910_pm_finish(void)
+{
+	pxa910_pm_enter_lowpower_mode(POWER_MODE_CORE_INTIDLE);
+}
+
+static int pxa910_pm_valid(suspend_state_t state)
+{
+	return ((state == PM_SUSPEND_STANDBY) || (state == PM_SUSPEND_MEM));
+}
+
+static const struct platform_suspend_ops pxa910_pm_ops = {
+	.valid		= pxa910_pm_valid,
+	.prepare	= pxa910_pm_prepare,
+	.enter		= pxa910_pm_enter,
+	.finish		= pxa910_pm_finish,
+};
+
+static int __init pxa910_pm_init(void)
+{
+	uint32_t awucrm = 0;
+
+	if (!cpu_is_pxa910())
+		return -EIO;
+
+	suspend_set_ops(&pxa910_pm_ops);
+
+	/* Set the following bits for MMP3 playback with VCTXO on */
+	__raw_writel(__raw_readl(APMU_SQU_CLK_GATE_CTRL) | (1 << 30),
+		APMU_SQU_CLK_GATE_CTRL);
+	__raw_writel(__raw_readl(MPMU_FCCR) | (1 << 28), MPMU_FCCR);
+
+	awucrm |= MPMU_AWUCRM_AP_ASYNC_INT | MPMU_AWUCRM_AP_FULL_IDLE;
+	__raw_writel(awucrm, MPMU_AWUCRM);
+
+	return 0;
+}
+
+late_initcall(pxa910_pm_init);

arch/arm/mach-mmp/ttc_dkb.c

@@ -17,6 +17,7 @@
 #include <linux/interrupt.h>
 #include <linux/i2c/pca953x.h>
 #include <linux/gpio.h>
+#include <linux/mfd/88pm860x.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -135,7 +136,17 @@ static struct pca953x_platform_data max7312_data[] = {
 	},
 };
 
+static struct pm860x_platform_data ttc_dkb_pm8607_info = {
+	.irq_base       = IRQ_BOARD_START,
+};
+
 static struct i2c_board_info ttc_dkb_i2c_info[] = {
+	{
+		.type           = "88PM860x",
+		.addr           = 0x34,
+		.platform_data  = &ttc_dkb_pm8607_info,
+		.irq            = IRQ_PXA910_PMIC_INT,
+	},
 	{
 		.type		= "max7312",
 		.addr		= 0x23,

arch/arm/mach-omap2/Makefile

@@ -4,7 +4,7 @@
 
 # Common support
 obj-y := id.o io.o control.o mux.o devices.o serial.o gpmc.o timer.o pm.o \
-	 common.o gpio.o dma.o wd_timer.o display.o i2c.o
+	 common.o gpio.o dma.o wd_timer.o display.o i2c.o hdq1w.o
 
 omap-2-3-common				= irq.o sdrc.o
 hwmod-common				= omap_hwmod.o \
@@ -118,16 +118,18 @@ obj-$(CONFIG_ARCH_OMAP4)		+= $(powerdomain-common) \
 					   powerdomains44xx_data.o
 
 # PRCM clockdomain control
-obj-$(CONFIG_ARCH_OMAP2)		+= clockdomain.o \
+clockdomain-common			+= clockdomain.o \
+					   clockdomains_common_data.o
+obj-$(CONFIG_ARCH_OMAP2)		+= $(clockdomain-common) \
 					   clockdomain2xxx_3xxx.o \
 					   clockdomains2xxx_3xxx_data.o
 obj-$(CONFIG_SOC_OMAP2420)		+= clockdomains2420_data.o
 obj-$(CONFIG_SOC_OMAP2430)		+= clockdomains2430_data.o
-obj-$(CONFIG_ARCH_OMAP3)		+= clockdomain.o \
+obj-$(CONFIG_ARCH_OMAP3)		+= $(clockdomain-common) \
 					   clockdomain2xxx_3xxx.o \
 					   clockdomains2xxx_3xxx_data.o \
 					   clockdomains3xxx_data.o
-obj-$(CONFIG_ARCH_OMAP4)		+= clockdomain.o \
+obj-$(CONFIG_ARCH_OMAP4)		+= $(clockdomain-common) \
 					   clockdomain44xx.o \
 					   clockdomains44xx_data.o
 
@@ -187,6 +189,9 @@ ifneq ($(CONFIG_TIDSPBRIDGE),)
 obj-y					+= dsp.o
 endif
 
+# OMAP2420 MSDI controller integration support ("MMC")
+obj-$(CONFIG_SOC_OMAP2420)		+= msdi.o
+
 # Specific board support
 obj-$(CONFIG_MACH_OMAP_GENERIC)		+= board-generic.o
 obj-$(CONFIG_MACH_OMAP_H4)		+= board-h4.o

arch/arm/mach-omap2/clock.c

@@ -439,7 +439,7 @@ void omap2_clk_disable_unused(struct clk *clk)
 		clk->ops->disable(clk);
 	}
 	if (clk->clkdm != NULL)
-		pwrdm_clkdm_state_switch(clk->clkdm);
+		pwrdm_state_switch(clk->clkdm->pwrdm.ptr);
 }
 #endif
 

arch/arm/mach-omap2/clock3xxx_data.c

 /*
  * OMAP3 clock data
  *
- * Copyright (C) 2007-2010 Texas Instruments, Inc.
+ * Copyright (C) 2007-2010, 2012 Texas Instruments, Inc.
  * Copyright (C) 2007-2011 Nokia Corporation
  *
  * Written by Paul Walmsley
@@ -1640,6 +1640,7 @@ static struct clk hdq_fck = {
 	.name		= "hdq_fck",
 	.ops		= &clkops_omap2_dflt_wait,
 	.parent		= &core_12m_fck,
+	.clkdm_name	= "core_l4_clkdm",
 	.enable_reg	= OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1),
 	.enable_bit	= OMAP3430_EN_HDQ_SHIFT,
 	.recalc		= &followparent_recalc,
@@ -3294,8 +3295,8 @@ static struct omap_clk omap3xxx_clks[] = {
 	CLK(NULL,	"gfx_l3_ick",	&gfx_l3_ick,	CK_3430ES1),
 	CLK(NULL,	"gfx_cg1_ck",	&gfx_cg1_ck,	CK_3430ES1),
 	CLK(NULL,	"gfx_cg2_ck",	&gfx_cg2_ck,	CK_3430ES1),
-	CLK(NULL,	"sgx_fck",	&sgx_fck,	CK_3430ES2PLUS | CK_3517 | CK_36XX),
-	CLK(NULL,	"sgx_ick",	&sgx_ick,	CK_3430ES2PLUS | CK_3517 | CK_36XX),
+	CLK(NULL,	"sgx_fck",	&sgx_fck,	CK_3430ES2PLUS | CK_AM35XX | CK_36XX),
+	CLK(NULL,	"sgx_ick",	&sgx_ick,	CK_3430ES2PLUS | CK_AM35XX | CK_36XX),
 	CLK(NULL,	"d2d_26m_fck",	&d2d_26m_fck,	CK_3430ES1),
 	CLK(NULL,	"modem_fck",	&modem_fck,	CK_34XX | CK_36XX),
 	CLK(NULL,	"sad2d_ick",	&sad2d_ick,	CK_34XX | CK_36XX),
@@ -3419,7 +3420,7 @@ static struct omap_clk omap3xxx_clks[] = {
 	CLK(NULL,	"per_48m_fck",	&per_48m_fck,	CK_3XXX),
 	CLK(NULL,	"uart3_fck",	&uart3_fck,	CK_3XXX),
 	CLK(NULL,	"uart4_fck",	&uart4_fck,	CK_36XX),
-	CLK(NULL,	"uart4_fck",	&uart4_fck_am35xx, CK_3505 | CK_3517),
+	CLK(NULL,	"uart4_fck",	&uart4_fck_am35xx, CK_AM35XX),
 	CLK(NULL,	"gpt2_fck",	&gpt2_fck,	CK_3XXX),
 	CLK(NULL,	"gpt3_fck",	&gpt3_fck,	CK_3XXX),
 	CLK(NULL,	"gpt4_fck",	&gpt4_fck,	CK_3XXX),
@@ -3513,21 +3514,9 @@ int __init omap3xxx_clk_init(void)
 	struct omap_clk *c;
 	u32 cpu_clkflg = 0;
 
-	/*
-	 * 3505 must be tested before 3517, since 3517 returns true
-	 * for both AM3517 chips and AM3517 family chips, which
-	 * includes 3505.  Unfortunately there's no obvious family
-	 * test for 3517/3505 :-(
-	 */
-	if (cpu_is_omap3505()) {
-		cpu_mask = RATE_IN_34XX;
-		cpu_clkflg = CK_3505;
-	} else if (cpu_is_omap3517()) {
-		cpu_mask = RATE_IN_34XX;
-		cpu_clkflg = CK_3517;
-	} else if (cpu_is_omap3505()) {
+	if (cpu_is_omap3517()) {
 		cpu_mask = RATE_IN_34XX;
-		cpu_clkflg = CK_3505;
+		cpu_clkflg = CK_AM35XX;
 	} else if (cpu_is_omap3630()) {
 		cpu_mask = (RATE_IN_34XX | RATE_IN_36XX);
 		cpu_clkflg = CK_36XX;

arch/arm/mach-omap2/clock44xx_data.c

@@ -3355,17 +3355,6 @@ static struct omap_clk omap44xx_clks[] = {
 	CLK(NULL,	"auxclk5_ck",			&auxclk5_ck,	CK_443X),
 	CLK(NULL,	"auxclkreq5_ck",		&auxclkreq5_ck,	CK_443X),
 	CLK(NULL,	"gpmc_ck",			&dummy_ck,	CK_443X),
-	CLK(NULL,	"gpt1_ick",			&dummy_ck,	CK_443X),
-	CLK(NULL,	"gpt2_ick",			&dummy_ck,	CK_443X),
-	CLK(NULL,	"gpt3_ick",			&dummy_ck,	CK_443X),
-	CLK(NULL,	"gpt4_ick",			&dummy_ck,	CK_443X),
-	CLK(NULL,	"gpt5_ick",			&dummy_ck,	CK_443X),
-	CLK(NULL,	"gpt6_ick",			&dummy_ck,	CK_443X),
-	CLK(NULL,	"gpt7_ick",			&dummy_ck,	CK_443X),
-	CLK(NULL,	"gpt8_ick",			&dummy_ck,	CK_443X),
-	CLK(NULL,	"gpt9_ick",			&dummy_ck,	CK_443X),
-	CLK(NULL,	"gpt10_ick",			&dummy_ck,	CK_443X),
-	CLK(NULL,	"gpt11_ick",			&dummy_ck,	CK_443X),
 	CLK("omap_i2c.1",	"ick",				&dummy_ck,	CK_443X),
 	CLK("omap_i2c.2",	"ick",				&dummy_ck,	CK_443X),
 	CLK("omap_i2c.3",	"ick",				&dummy_ck,	CK_443X),

arch/arm/mach-omap2/clockdomain.c

@@ -840,7 +840,7 @@ void clkdm_allow_idle(struct clockdomain *clkdm)
 	spin_lock_irqsave(&clkdm->lock, flags);
 	clkdm->_flags |= _CLKDM_FLAG_HWSUP_ENABLED;
 	arch_clkdm->clkdm_allow_idle(clkdm);
-	pwrdm_clkdm_state_switch(clkdm);
+	pwrdm_state_switch(clkdm->pwrdm.ptr);
 	spin_unlock_irqrestore(&clkdm->lock, flags);
 }
 
@@ -924,8 +924,7 @@ static int _clkdm_clk_hwmod_enable(struct clockdomain *clkdm)
 
 	spin_lock_irqsave(&clkdm->lock, flags);
 	arch_clkdm->clkdm_clk_enable(clkdm);
-	pwrdm_wait_transition(clkdm->pwrdm.ptr);
-	pwrdm_clkdm_state_switch(clkdm);
+	pwrdm_state_switch(clkdm->pwrdm.ptr);
 	spin_unlock_irqrestore(&clkdm->lock, flags);
 
 	pr_debug("clockdomain: clkdm %s: enabled\n", clkdm->name);
@@ -950,7 +949,7 @@ static int _clkdm_clk_hwmod_disable(struct clockdomain *clkdm)
 
 	spin_lock_irqsave(&clkdm->lock, flags);
 	arch_clkdm->clkdm_clk_disable(clkdm);
-	pwrdm_clkdm_state_switch(clkdm);
+	pwrdm_state_switch(clkdm->pwrdm.ptr);
 	spin_unlock_irqrestore(&clkdm->lock, flags);
 
 	pr_debug("clockdomain: clkdm %s: disabled\n", clkdm->name);

arch/arm/mach-omap2/clockdomain44xx.c

@@ -51,6 +51,9 @@ static int omap4_clkdm_clear_all_wkup_sleep_deps(struct clockdomain *clkdm)
 	struct clkdm_dep *cd;
 	u32 mask = 0;
 
+	if (!clkdm->prcm_partition)
+		return 0;
+
 	for (cd = clkdm->wkdep_srcs; cd && cd->clkdm_name; cd++) {
 		if (!cd->clkdm)
 			continue; /* only happens if data is erroneous */
@@ -103,6 +106,9 @@ static int omap4_clkdm_clk_disable(struct clockdomain *clkdm)
 {
 	bool hwsup = false;
 
+	if (!clkdm->prcm_partition)
+		return 0;
+
 	hwsup = omap4_cminst_is_clkdm_in_hwsup(clkdm->prcm_partition,
 					clkdm->cm_inst, clkdm->clkdm_offs);
 

arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c

@@ -89,13 +89,3 @@ struct clockdomain wkup_common_clkdm = {
 	.pwrdm		= { .name = "wkup_pwrdm" },
 	.dep_bit	= OMAP_EN_WKUP_SHIFT,
 };
-
-struct clockdomain prm_common_clkdm = {
-	.name		= "prm_clkdm",
-	.pwrdm		= { .name = "wkup_pwrdm" },
-};
-
-struct clockdomain cm_common_clkdm = {
-	.name		= "cm_clkdm",
-	.pwrdm		= { .name = "core_pwrdm" },
-};

arch/arm/mach-omap2/clockdomains3xxx_data.c

@@ -53,9 +53,9 @@
  * 3430ES2 PM_WKDEP_SGX: adds IVA2, removes CORE
  */
 static struct clkdm_dep gfx_sgx_3xxx_wkdeps[] = {
-	{ .clkdm_name = "iva2_clkdm", },
-	{ .clkdm_name = "mpu_clkdm", },
-	{ .clkdm_name = "wkup_clkdm", },
+	{ .clkdm_name = "iva2_clkdm" },
+	{ .clkdm_name = "mpu_clkdm" },
+	{ .clkdm_name = "wkup_clkdm" },
 	{ NULL },
 };
 

arch/arm/mach-omap2/clockdomains44xx_data.c

@@ -430,6 +430,8 @@ static struct clockdomain *clockdomains_omap44xx[] __initdata = {
 	&l4_wkup_44xx_clkdm,
 	&emu_sys_44xx_clkdm,
 	&l3_dma_44xx_clkdm,
+	&prm_common_clkdm,
+	&cm_common_clkdm,
 	NULL
 };
 

arch/arm/mach-omap2/clockdomains_common_data.c

+/*
+ * OMAP2+-common clockdomain data
+ *
+ * Copyright (C) 2008-2012 Texas Instruments, Inc.
+ * Copyright (C) 2008-2010 Nokia Corporation
+ *
+ * Paul Walmsley, Jouni Högander
+ */
+
+#include <linux/kernel.h>
+#include <linux/io.h>
+
+#include "clockdomain.h"
+
+/* These are implicit clockdomains - they are never defined as such in TRM */
+struct clockdomain prm_common_clkdm = {
+	.name		= "prm_clkdm",
+	.pwrdm		= { .name = "wkup_pwrdm" },
+};
+
+struct clockdomain cm_common_clkdm = {
+	.name		= "cm_clkdm",
+	.pwrdm		= { .name = "core_pwrdm" },
+};

arch/arm/mach-omap2/cm-regbits-34xx.h

@@ -79,7 +79,7 @@
 
 /* CM_CLKSEL1_PLL_IVA2 */
 #define OMAP3430_IVA2_CLK_SRC_SHIFT			19
-#define OMAP3430_IVA2_CLK_SRC_MASK			(0x3 << 19)
+#define OMAP3430_IVA2_CLK_SRC_MASK			(0x7 << 19)
 #define OMAP3430_IVA2_DPLL_MULT_SHIFT			8
 #define OMAP3430_IVA2_DPLL_MULT_MASK			(0x7ff << 8)
 #define OMAP3430_IVA2_DPLL_DIV_SHIFT			0
@@ -124,7 +124,7 @@
 
 /* CM_CLKSEL1_PLL_MPU */
 #define OMAP3430_MPU_CLK_SRC_SHIFT			19
-#define OMAP3430_MPU_CLK_SRC_MASK			(0x3 << 19)
+#define OMAP3430_MPU_CLK_SRC_MASK			(0x7 << 19)
 #define OMAP3430_MPU_DPLL_MULT_SHIFT			8
 #define OMAP3430_MPU_DPLL_MULT_MASK			(0x7ff << 8)
 #define OMAP3430_MPU_DPLL_DIV_SHIFT			0

arch/arm/mach-omap2/cminst44xx.c

@@ -32,6 +32,7 @@
 #include "prcm44xx.h"
 #include "prm44xx.h"
 #include "prcm_mpu44xx.h"
+#include "prcm-common.h"
 
 /*
  * CLKCTRL_IDLEST_*: possible values for the CM_*_CLKCTRL.IDLEST bitfield:
@@ -49,14 +50,21 @@
 #define CLKCTRL_IDLEST_INTERFACE_IDLE		0x2
 #define CLKCTRL_IDLEST_DISABLED			0x3
 
-static u32 _cm_bases[OMAP4_MAX_PRCM_PARTITIONS] = {
-	[OMAP4430_INVALID_PRCM_PARTITION]	= 0,
-	[OMAP4430_PRM_PARTITION]		= OMAP4430_PRM_BASE,
-	[OMAP4430_CM1_PARTITION]		= OMAP4430_CM1_BASE,
-	[OMAP4430_CM2_PARTITION]		= OMAP4430_CM2_BASE,
-	[OMAP4430_SCRM_PARTITION]		= 0,
-	[OMAP4430_PRCM_MPU_PARTITION]		= OMAP4430_PRCM_MPU_BASE,
-};
+static void __iomem *_cm_bases[OMAP4_MAX_PRCM_PARTITIONS];
+
+/**
+ * omap_cm_base_init - Populates the cm partitions
+ *
+ * Populates the base addresses of the _cm_bases
+ * array used for read/write of cm module registers.
+ */
+void omap_cm_base_init(void)
+{
+	_cm_bases[OMAP4430_PRM_PARTITION] = prm_base;
+	_cm_bases[OMAP4430_CM1_PARTITION] = cm_base;
+	_cm_bases[OMAP4430_CM2_PARTITION] = cm2_base;
+	_cm_bases[OMAP4430_PRCM_MPU_PARTITION] = prcm_mpu_base;
+}
 
 /* Private functions */
 
@@ -106,7 +114,7 @@ u32 omap4_cminst_read_inst_reg(u8 part, s16 inst, u16 idx)
 	BUG_ON(part >= OMAP4_MAX_PRCM_PARTITIONS ||
 	       part == OMAP4430_INVALID_PRCM_PARTITION ||
 	       !_cm_bases[part]);
-	return __raw_readl(OMAP2_L4_IO_ADDRESS(_cm_bases[part] + inst + idx));
+	return __raw_readl(_cm_bases[part] + inst + idx);
 }
 
 /* Write into a register in a CM instance */
@@ -115,7 +123,7 @@ void omap4_cminst_write_inst_reg(u32 val, u8 part, s16 inst, u16 idx)
 	BUG_ON(part >= OMAP4_MAX_PRCM_PARTITIONS ||
 	       part == OMAP4430_INVALID_PRCM_PARTITION ||
 	       !_cm_bases[part]);
-	__raw_writel(val, OMAP2_L4_IO_ADDRESS(_cm_bases[part] + inst + idx));
+	__raw_writel(val, _cm_bases[part] + inst + idx);
 }
 
 /* Read-modify-write a register in CM1. Caller must lock */

arch/arm/mach-omap2/common.c

@@ -166,6 +166,7 @@ static struct omap_globals omap4_globals = {
 	.prm	= OMAP2_L4_IO_ADDRESS(OMAP4430_PRM_BASE),
 	.cm	= OMAP2_L4_IO_ADDRESS(OMAP4430_CM_BASE),
 	.cm2	= OMAP2_L4_IO_ADDRESS(OMAP4430_CM2_BASE),
+	.prcm_mpu	= OMAP2_L4_IO_ADDRESS(OMAP4430_PRCM_MPU_BASE),
 };
 
 void __init omap2_set_globals_443x(void)

arch/arm/mach-omap2/common.h

@@ -112,6 +112,7 @@ struct omap_globals {
 	void __iomem	*prm;            /* Power and Reset Management */
 	void __iomem	*cm;             /* Clock Management */
 	void __iomem	*cm2;
+	void __iomem	*prcm_mpu;
 };
 
 void omap2_set_globals_242x(void);

arch/arm/mach-omap2/dpll3xxx.c

@@ -142,6 +142,7 @@ static int _omap3_noncore_dpll_lock(struct clk *clk)
 
 	ai = omap3_dpll_autoidle_read(clk);
 
+	if (ai)
 		omap3_dpll_deny_idle(clk);
 
 	_omap3_dpll_write_clken(clk, DPLL_LOCKED);
@@ -186,8 +187,6 @@ static int _omap3_noncore_dpll_bypass(struct clk *clk)
 
 	if (ai)
 		omap3_dpll_allow_idle(clk);
-	else
-		omap3_dpll_deny_idle(clk);
 
 	return r;
 }
@@ -216,8 +215,6 @@ static int _omap3_noncore_dpll_stop(struct clk *clk)
 
 	if (ai)
 		omap3_dpll_allow_idle(clk);
-	else
-		omap3_dpll_deny_idle(clk);
 
 	return 0;
 }
@@ -519,6 +516,9 @@ u32 omap3_dpll_autoidle_read(struct clk *clk)
 
 	dd = clk->dpll_data;
 
+	if (!dd->autoidle_reg)
+		return -EINVAL;
+
 	v = __raw_readl(dd->autoidle_reg);
 	v &= dd->autoidle_mask;
 	v >>= __ffs(dd->autoidle_mask);
@@ -545,6 +545,12 @@ void omap3_dpll_allow_idle(struct clk *clk)
 
 	dd = clk->dpll_data;
 
+	if (!dd->autoidle_reg) {
+		pr_debug("clock: DPLL %s: autoidle not supported\n",
+			clk->name);
+		return;
+	}
+
 	/*
 	 * REVISIT: CORE DPLL can optionally enter low-power bypass
 	 * by writing 0x5 instead of 0x1.  Add some mechanism to
@@ -554,6 +560,7 @@ void omap3_dpll_allow_idle(struct clk *clk)
 	v &= ~dd->autoidle_mask;
 	v |= DPLL_AUTOIDLE_LOW_POWER_STOP << __ffs(dd->autoidle_mask);
 	__raw_writel(v, dd->autoidle_reg);
+
 }
 
 /**
@@ -572,6 +579,12 @@ void omap3_dpll_deny_idle(struct clk *clk)
 
 	dd = clk->dpll_data;
 
+	if (!dd->autoidle_reg) {
+		pr_debug("clock: DPLL %s: autoidle not supported\n",
+			clk->name);
+		return;
+	}
+
 	v = __raw_readl(dd->autoidle_reg);
 	v &= ~dd->autoidle_mask;
 	v |= DPLL_AUTOIDLE_DISABLE << __ffs(dd->autoidle_mask);

arch/arm/mach-omap2/hdq1w.c

+/*
+ * IP block integration code for the HDQ1W/1-wire IP block
+ *
+ * Copyright (C) 2012 Texas Instruments, Inc.
+ * Paul Walmsley
+ *
+ * Based on the I2C reset code in arch/arm/mach-omap2/i2c.c by
+ *     Avinash.H.M <avinashhm@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ */
+
+#include <plat/omap_hwmod.h>
+#include <plat/hdq1w.h>
+
+#include "common.h"
+
+/* Maximum microseconds to wait for OMAP module to softreset */
+#define MAX_MODULE_SOFTRESET_WAIT	10000
+
+/**
+ * omap_hdq1w_reset - reset the OMAP HDQ1W module
+ * @oh: struct omap_hwmod *
+ *
+ * OCP soft reset the HDQ1W IP block.  Section 20.6.1.4 "HDQ1W/1-Wire
+ * Software Reset" of the OMAP34xx Technical Reference Manual Revision
+ * ZR (SWPU223R) does not include the rather important fact that, for
+ * the reset to succeed, the HDQ1W module's internal clock gate must be
+ * programmed to allow the clock to propagate to the rest of the
+ * module.  In this sense, it's rather similar to the I2C custom reset
+ * function.  Returns 0.
+ */
+int omap_hdq1w_reset(struct omap_hwmod *oh)
+{
+	u32 v;
+	int c = 0;
+
+	/* Write to the SOFTRESET bit */
+	omap_hwmod_softreset(oh);
+
+	/* Enable the module's internal clocks */
+	v = omap_hwmod_read(oh, HDQ_CTRL_STATUS_OFFSET);
+	v |= 1 << HDQ_CTRL_STATUS_CLOCKENABLE_SHIFT;
+	omap_hwmod_write(v, oh, HDQ_CTRL_STATUS_OFFSET);
+
+	/* Poll on RESETDONE bit */
+	omap_test_timeout((omap_hwmod_read(oh,
+					   oh->class->sysc->syss_offs)
+			   & SYSS_RESETDONE_MASK),
+			  MAX_MODULE_SOFTRESET_WAIT, c);
+
+	if (c == MAX_MODULE_SOFTRESET_WAIT)
+		pr_warning("%s: %s: softreset failed (waited %d usec)\n",
+			   __func__, oh->name, MAX_MODULE_SOFTRESET_WAIT);
+	else
+		pr_debug("%s: %s: softreset in %d usec\n", __func__,
+			 oh->name, c);
+
+	return 0;
+}

arch/arm/mach-omap2/io.c

@@ -364,24 +364,6 @@ static void __init omap_hwmod_init_postsetup(void)
 #endif
 	omap_hwmod_for_each(_set_hwmod_postsetup_state, &postsetup_state);
 
-	/*
-	 * Set the default postsetup state for unusual modules (like
-	 * MPU WDT).
-	 *
-	 * The postsetup_state is not actually used until
-	 * omap_hwmod_late_init(), so boards that desire full watchdog
-	 * coverage of kernel initialization can reprogram the
-	 * postsetup_state between the calls to
-	 * omap2_init_common_infra() and omap_sdrc_init().
-	 *
-	 * XXX ideally we could detect whether the MPU WDT was currently
-	 * enabled here and make this conditional
-	 */
-	postsetup_state = _HWMOD_STATE_DISABLED;
-	omap_hwmod_for_each_by_class("wd_timer",
-				     _set_hwmod_postsetup_state,
-				     &postsetup_state);
-
 	omap_pm_if_early_init();
 }
 

arch/arm/mach-omap2/msdi.c

+/*
+ * MSDI IP block reset
+ *
+ * Copyright (C) 2012 Texas Instruments, Inc.
+ * Paul Walmsley
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ * XXX What about pad muxing?
+ */
+
+#include <linux/kernel.h>
+
+#include <plat/omap_hwmod.h>
+#include <plat/mmc.h>
+
+#include "common.h"
+
+/*
+ * MSDI_CON_OFFSET: offset in bytes of the MSDI IP block's CON register
+ *     from the IP block's base address
+ */
+#define MSDI_CON_OFFSET				0x0c
+
+/* Register bitfields in the CON register */
+#define MSDI_CON_POW_MASK			BIT(11)
+#define MSDI_CON_CLKD_MASK			(0x3f << 0)
+#define MSDI_CON_CLKD_SHIFT			0
+
+/* Maximum microseconds to wait for OMAP module to softreset */
+#define MAX_MODULE_SOFTRESET_WAIT	10000
+
+/* MSDI_TARGET_RESET_CLKD: clock divisor to use throughout the reset */
+#define MSDI_TARGET_RESET_CLKD		0x3ff
+
+/**
+ * omap_msdi_reset - reset the MSDI IP block
+ * @oh: struct omap_hwmod *
+ *
+ * The MSDI IP block on OMAP2420 has to have both the POW and CLKD
+ * fields set inside its CON register for a reset to complete
+ * successfully.  This is not documented in the TRM.  For CLKD, we use
+ * the value that results in the lowest possible clock rate, to attempt
+ * to avoid disturbing any cards.
+ */
+int omap_msdi_reset(struct omap_hwmod *oh)
+{
+	u16 v = 0;
+	int c = 0;
+
+	/* Write to the SOFTRESET bit */
+	omap_hwmod_softreset(oh);
+
+	/* Enable the MSDI core and internal clock */
+	v |= MSDI_CON_POW_MASK;
+	v |= MSDI_TARGET_RESET_CLKD << MSDI_CON_CLKD_SHIFT;
+	omap_hwmod_write(v, oh, MSDI_CON_OFFSET);
+
+	/* Poll on RESETDONE bit */
+	omap_test_timeout((omap_hwmod_read(oh, oh->class->sysc->syss_offs)
+			   & SYSS_RESETDONE_MASK),
+			  MAX_MODULE_SOFTRESET_WAIT, c);
+
+	if (c == MAX_MODULE_SOFTRESET_WAIT)
+		pr_warning("%s: %s: softreset failed (waited %d usec)\n",
+			   __func__, oh->name, MAX_MODULE_SOFTRESET_WAIT);
+	else
+		pr_debug("%s: %s: softreset in %d usec\n", __func__,
+			 oh->name, c);
+
+	/* Disable the MSDI internal clock */
+	v &= ~MSDI_CON_CLKD_MASK;
+	omap_hwmod_write(v, oh, MSDI_CON_OFFSET);
+
+	return 0;
+}

arch/arm/mach-omap2/omap_hwmod_2420_data.c

@@ -23,6 +23,7 @@
 #include <plat/dmtimer.h>
 #include <plat/l3_2xxx.h>
 #include <plat/l4_2xxx.h>
+#include <plat/mmc.h>
 
 #include "omap_hwmod_common_data.h"
 
@@ -239,6 +240,67 @@ static struct omap_hwmod omap2420_mcbsp2_hwmod = {
 	},
 };
 
+static struct omap_hwmod_class_sysconfig omap2420_msdi_sysc = {
+	.rev_offs	= 0x3c,
+	.sysc_offs	= 0x64,
+	.syss_offs	= 0x68,
+	.sysc_flags	= (SYSC_HAS_SOFTRESET | SYSS_HAS_RESET_STATUS),
+	.sysc_fields	= &omap_hwmod_sysc_type1,
+};
+
+static struct omap_hwmod_class omap2420_msdi_hwmod_class = {
+	.name	= "msdi",
+	.sysc	= &omap2420_msdi_sysc,
+	.reset	= &omap_msdi_reset,
+};
+
+/* msdi1 */
+static struct omap_hwmod_irq_info omap2420_msdi1_irqs[] = {
+	{ .irq = 83 },
+	{ .irq = -1 }
+};
+
+static struct omap_hwmod_dma_info omap2420_msdi1_sdma_reqs[] = {
+	{ .name = "tx", .dma_req = 61 }, /* OMAP24XX_DMA_MMC1_TX */
+	{ .name = "rx", .dma_req = 62 }, /* OMAP24XX_DMA_MMC1_RX */
+	{ .dma_req = -1 }
+};
+
+static struct omap_hwmod omap2420_msdi1_hwmod = {
+	.name		= "msdi1",
+	.class		= &omap2420_msdi_hwmod_class,
+	.mpu_irqs	= omap2420_msdi1_irqs,
+	.sdma_reqs	= omap2420_msdi1_sdma_reqs,
+	.main_clk	= "mmc_fck",
+	.prcm		= {
+		.omap2 = {
+			.prcm_reg_id = 1,
+			.module_bit = OMAP2420_EN_MMC_SHIFT,
+			.module_offs = CORE_MOD,
+			.idlest_reg_id = 1,
+			.idlest_idle_bit = OMAP2420_ST_MMC_SHIFT,
+		},
+	},
+	.flags		= HWMOD_16BIT_REG,
+};
+
+/* HDQ1W/1-wire */
+static struct omap_hwmod omap2420_hdq1w_hwmod = {
+	.name		= "hdq1w",
+	.mpu_irqs	= omap2_hdq1w_mpu_irqs,
+	.main_clk	= "hdq_fck",
+	.prcm		= {
+		.omap2 = {
+			.module_offs = CORE_MOD,
+			.prcm_reg_id = 1,
+			.module_bit = OMAP24XX_EN_HDQ_SHIFT,
+			.idlest_reg_id = 1,
+			.idlest_idle_bit = OMAP24XX_ST_HDQ_SHIFT,
+		},
+	},
+	.class		= &omap2_hdq1w_class,
+};
+
 /*
  * interfaces
  */
@@ -428,6 +490,53 @@ static struct omap_hwmod_ocp_if omap2420_l4_core__mcbsp2 = {
 	.user		= OCP_USER_MPU | OCP_USER_SDMA,
 };
 
+static struct omap_hwmod_addr_space omap2420_msdi1_addrs[] = {
+	{
+		.pa_start	= 0x4809c000,
+		.pa_end		= 0x4809c000 + SZ_128 - 1,
+		.flags		= ADDR_TYPE_RT,
+	},
+	{ }
+};
+
+/* l4_core -> msdi1 */
+static struct omap_hwmod_ocp_if omap2420_l4_core__msdi1 = {
+	.master		= &omap2xxx_l4_core_hwmod,
+	.slave		= &omap2420_msdi1_hwmod,
+	.clk		= "mmc_ick",
+	.addr		= omap2420_msdi1_addrs,
+	.user		= OCP_USER_MPU | OCP_USER_SDMA,
+};
+
+/* l4_core -> hdq1w interface */
+static struct omap_hwmod_ocp_if omap2420_l4_core__hdq1w = {
+	.master		= &omap2xxx_l4_core_hwmod,
+	.slave		= &omap2420_hdq1w_hwmod,
+	.clk		= "hdq_ick",
+	.addr		= omap2_hdq1w_addr_space,
+	.user		= OCP_USER_MPU | OCP_USER_SDMA,
+	.flags		= OMAP_FIREWALL_L4 | OCPIF_SWSUP_IDLE,
+};
+
+
+/* l4_wkup -> 32ksync_counter */
+static struct omap_hwmod_addr_space omap2420_counter_32k_addrs[] = {
+	{
+		.pa_start	= 0x48004000,
+		.pa_end		= 0x4800401f,
+		.flags		= ADDR_TYPE_RT
+	},
+	{ }
+};
+
+static struct omap_hwmod_ocp_if omap2420_l4_wkup__counter_32k = {
+	.master		= &omap2xxx_l4_wkup_hwmod,
+	.slave		= &omap2xxx_counter_32k_hwmod,
+	.clk		= "sync_32k_ick",
+	.addr		= omap2420_counter_32k_addrs,
+	.user		= OCP_USER_MPU | OCP_USER_SDMA,
+};
+
 static struct omap_hwmod_ocp_if *omap2420_hwmod_ocp_ifs[] __initdata = {
 	&omap2xxx_l3_main__l4_core,
 	&omap2xxx_mpu__l3_main,
@@ -468,6 +577,9 @@ static struct omap_hwmod_ocp_if *omap2420_hwmod_ocp_ifs[] __initdata = {
 	&omap2420_l4_core__mailbox,
 	&omap2420_l4_core__mcbsp1,
 	&omap2420_l4_core__mcbsp2,
+	&omap2420_l4_core__msdi1,
+	&omap2420_l4_core__hdq1w,
+	&omap2420_l4_wkup__counter_32k,
 	NULL,
 };
 

arch/arm/mach-omap2/omap_hwmod_2430_data.c

@@ -528,6 +528,23 @@ static struct omap_hwmod omap2430_mmc2_hwmod = {
 	.class		= &omap2430_mmc_class,
 };
 
+/* HDQ1W/1-wire */
+static struct omap_hwmod omap2430_hdq1w_hwmod = {
+	.name		= "hdq1w",
+	.mpu_irqs	= omap2_hdq1w_mpu_irqs,
+	.main_clk	= "hdq_fck",
+	.prcm		= {
+		.omap2 = {
+			.module_offs = CORE_MOD,
+			.prcm_reg_id = 1,
+			.module_bit = OMAP24XX_EN_HDQ_SHIFT,
+			.idlest_reg_id = 1,
+			.idlest_idle_bit = OMAP24XX_ST_HDQ_SHIFT,
+		},
+	},
+	.class		= &omap2_hdq1w_class,
+};
+
 /*
  * interfaces
  */
@@ -838,6 +855,34 @@ static struct omap_hwmod_ocp_if omap2430_l4_core__mcbsp5 = {
 	.user		= OCP_USER_MPU | OCP_USER_SDMA,
 };
 
+/* l4_core -> hdq1w */
+static struct omap_hwmod_ocp_if omap2430_l4_core__hdq1w = {
+	.master		= &omap2xxx_l4_core_hwmod,
+	.slave		= &omap2430_hdq1w_hwmod,
+	.clk		= "hdq_ick",
+	.addr		= omap2_hdq1w_addr_space,
+	.user		= OCP_USER_MPU | OCP_USER_SDMA,
+	.flags		= OMAP_FIREWALL_L4 | OCPIF_SWSUP_IDLE,
+};
+
+/* l4_wkup -> 32ksync_counter */
+static struct omap_hwmod_addr_space omap2430_counter_32k_addrs[] = {
+	{
+		.pa_start	= 0x49020000,
+		.pa_end		= 0x4902001f,
+		.flags		= ADDR_TYPE_RT
+	},
+	{ }
+};
+
+static struct omap_hwmod_ocp_if omap2430_l4_wkup__counter_32k = {
+	.master		= &omap2xxx_l4_wkup_hwmod,
+	.slave		= &omap2xxx_counter_32k_hwmod,
+	.clk		= "sync_32k_ick",
+	.addr		= omap2430_counter_32k_addrs,
+	.user		= OCP_USER_MPU | OCP_USER_SDMA,
+};
+
 static struct omap_hwmod_ocp_if *omap2430_hwmod_ocp_ifs[] __initdata = {
 	&omap2xxx_l3_main__l4_core,
 	&omap2xxx_mpu__l3_main,
@@ -886,6 +931,8 @@ static struct omap_hwmod_ocp_if *omap2430_hwmod_ocp_ifs[] __initdata = {
 	&omap2430_l4_core__mcbsp3,
 	&omap2430_l4_core__mcbsp4,
 	&omap2430_l4_core__mcbsp5,
+	&omap2430_l4_core__hdq1w,
+	&omap2430_l4_wkup__counter_32k,
 	NULL,
 };
 

arch/arm/mach-omap2/omap_hwmod_2xxx_3xxx_interconnect_data.c

@@ -171,3 +171,12 @@ struct omap_hwmod_addr_space omap2_mcbsp1_addrs[] = {
 	},
 	{ }
 };
+
+struct omap_hwmod_addr_space omap2_hdq1w_addr_space[] = {
+	{
+		.pa_start       = 0x480b2000,
+		.pa_end         = 0x480b2fff,
+		.flags          = ADDR_TYPE_RT,
+	},
+	{ }
+};

arch/arm/mach-omap2/omap_hwmod_2xxx_3xxx_ipblock_data.c

@@ -2,6 +2,7 @@
  * omap_hwmod_2xxx_3xxx_ipblock_data.c - common IP block data for OMAP2/3
  *
  * Copyright (C) 2011 Nokia Corporation
+ * Copyright (C) 2012 Texas Instruments, Inc.
  * Paul Walmsley
  *
  * This program is free software; you can redistribute it and/or modify
@@ -12,6 +13,7 @@
 #include <plat/serial.h>
 #include <plat/dma.h>
 #include <plat/common.h>
+#include <plat/hdq1w.h>
 
 #include <mach/irqs.h>
 
@@ -302,3 +304,23 @@ struct omap_hwmod_irq_info omap2_mcspi2_mpu_irqs[] = {
 	{ .irq = -1 }
 };
 
+struct omap_hwmod_class_sysconfig omap2_hdq1w_sysc = {
+	.rev_offs	= 0x0,
+	.sysc_offs	= 0x14,
+	.syss_offs	= 0x18,
+	.sysc_flags	= (SYSC_HAS_SOFTRESET | SYSC_HAS_AUTOIDLE |
+			   SYSS_HAS_RESET_STATUS),
+	.sysc_fields    = &omap_hwmod_sysc_type1,
+};
+
+struct omap_hwmod_class omap2_hdq1w_class = {
+	.name	= "hdq1w",
+	.sysc	= &omap2_hdq1w_sysc,
+	.reset	= &omap_hdq1w_reset,
+};
+
+struct omap_hwmod_irq_info omap2_hdq1w_mpu_irqs[] = {
+	{ .irq = 58, },
+	{ .irq = -1 }
+};
+

arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c

@@ -89,7 +89,8 @@ static struct omap_hwmod_class_sysconfig omap2xxx_wd_timer_sysc = {
 struct omap_hwmod_class omap2xxx_wd_timer_hwmod_class = {
 	.name		= "wd_timer",
 	.sysc		= &omap2xxx_wd_timer_sysc,
-	.pre_shutdown	= &omap2_wd_timer_disable
+	.pre_shutdown	= &omap2_wd_timer_disable,
+	.reset		= &omap2_wd_timer_reset,
 };
 
 /*
@@ -732,3 +733,23 @@ struct omap_hwmod omap2xxx_mcspi2_hwmod = {
 	.class		= &omap2xxx_mcspi_class,
 	.dev_attr	= &omap_mcspi2_dev_attr,
 };
+
+
+static struct omap_hwmod_class omap2xxx_counter_hwmod_class = {
+	.name	= "counter",
+};
+
+struct omap_hwmod omap2xxx_counter_32k_hwmod = {
+	.name		= "counter_32k",
+	.main_clk	= "func_32k_ck",
+	.prcm		= {
+		.omap2	= {
+			.module_offs = WKUP_MOD,
+			.prcm_reg_id = 1,
+			.module_bit = OMAP24XX_ST_32KSYNC_SHIFT,
+			.idlest_reg_id = 1,
+			.idlest_idle_bit = OMAP24XX_ST_32KSYNC_SHIFT,
+		},
+	},
+	.class		= &omap2xxx_counter_hwmod_class,
+};

arch/arm/mach-omap2/omap_hwmod_3xxx_data.c

@@ -418,7 +418,8 @@ static struct omap_hwmod_class_sysconfig i2c_sysc = {
 static struct omap_hwmod_class omap3xxx_wd_timer_hwmod_class = {
 	.name		= "wd_timer",
 	.sysc		= &omap3xxx_wd_timer_sysc,
-	.pre_shutdown	= &omap2_wd_timer_disable
+	.pre_shutdown	= &omap2_wd_timer_disable,
+	.reset		= &omap2_wd_timer_reset,
 };
 
 static struct omap_hwmod omap3xxx_wd_timer2_hwmod = {
@@ -1075,7 +1076,7 @@ static struct omap_hwmod_class omap3xxx_mcbsp_hwmod_class = {
 
 /* mcbsp1 */
 static struct omap_hwmod_irq_info omap3xxx_mcbsp1_irqs[] = {
-	{ .name = "irq", .irq = 16 },
+	{ .name = "common", .irq = 16 },
 	{ .name = "tx", .irq = 59 },
 	{ .name = "rx", .irq = 60 },
 	{ .irq = -1 }
@@ -1100,7 +1101,7 @@ static struct omap_hwmod omap3xxx_mcbsp1_hwmod = {
 
 /* mcbsp2 */
 static struct omap_hwmod_irq_info omap3xxx_mcbsp2_irqs[] = {
-	{ .name = "irq", .irq = 17 },
+	{ .name = "common", .irq = 17 },
 	{ .name = "tx", .irq = 62 },
 	{ .name = "rx", .irq = 63 },
 	{ .irq = -1 }
@@ -1130,7 +1131,7 @@ static struct omap_hwmod omap3xxx_mcbsp2_hwmod = {
 
 /* mcbsp3 */
 static struct omap_hwmod_irq_info omap3xxx_mcbsp3_irqs[] = {
-	{ .name = "irq", .irq = 22 },
+	{ .name = "common", .irq = 22 },
 	{ .name = "tx", .irq = 89 },
 	{ .name = "rx", .irq = 90 },
 	{ .irq = -1 }
@@ -1160,7 +1161,7 @@ static struct omap_hwmod omap3xxx_mcbsp3_hwmod = {
 
 /* mcbsp4 */
 static struct omap_hwmod_irq_info omap3xxx_mcbsp4_irqs[] = {
-	{ .name = "irq", .irq = 23 },
+	{ .name = "common", .irq = 23 },
 	{ .name = "tx", .irq = 54 },
 	{ .name = "rx", .irq = 55 },
 	{ .irq = -1 }
@@ -1191,7 +1192,7 @@ static struct omap_hwmod omap3xxx_mcbsp4_hwmod = {
 
 /* mcbsp5 */
 static struct omap_hwmod_irq_info omap3xxx_mcbsp5_irqs[] = {
-	{ .name = "irq", .irq = 27 },
+	{ .name = "common", .irq = 27 },
 	{ .name = "tx", .irq = 81 },
 	{ .name = "rx", .irq = 82 },
 	{ .irq = -1 }
@@ -1980,6 +1981,56 @@ static struct omap_hwmod omap3xxx_usb_tll_hs_hwmod = {
 	},
 };
 
+static struct omap_hwmod omap3xxx_hdq1w_hwmod = {
+	.name		= "hdq1w",
+	.mpu_irqs	= omap2_hdq1w_mpu_irqs,
+	.main_clk	= "hdq_fck",
+	.prcm		= {
+		.omap2 = {
+			.module_offs = CORE_MOD,
+			.prcm_reg_id = 1,
+			.module_bit = OMAP3430_EN_HDQ_SHIFT,
+			.idlest_reg_id = 1,
+			.idlest_idle_bit = OMAP3430_ST_HDQ_SHIFT,
+		},
+	},
+	.class		= &omap2_hdq1w_class,
+};
+
+/*
+ * '32K sync counter' class
+ * 32-bit ordinary counter, clocked by the falling edge of the 32 khz clock
+ */
+static struct omap_hwmod_class_sysconfig omap3xxx_counter_sysc = {
+	.rev_offs	= 0x0000,
+	.sysc_offs	= 0x0004,
+	.sysc_flags	= SYSC_HAS_SIDLEMODE,
+	.idlemodes	= (SIDLE_FORCE | SIDLE_NO),
+	.sysc_fields	= &omap_hwmod_sysc_type1,
+};
+
+static struct omap_hwmod_class omap3xxx_counter_hwmod_class = {
+	.name	= "counter",
+	.sysc	= &omap3xxx_counter_sysc,
+};
+
+static struct omap_hwmod omap3xxx_counter_32k_hwmod = {
+	.name		= "counter_32k",
+	.class		= &omap3xxx_counter_hwmod_class,
+	.clkdm_name	= "wkup_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE,
+	.main_clk	= "wkup_32k_fck",
+	.prcm		= {
+		.omap2	= {
+			.module_offs = WKUP_MOD,
+			.prcm_reg_id = 1,
+			.module_bit = OMAP3430_ST_32KSYNC_SHIFT,
+			.idlest_reg_id = 1,
+			.idlest_idle_bit = OMAP3430_ST_32KSYNC_SHIFT,
+		},
+	},
+};
+
 /*
  * interfaces
  */
@@ -3059,6 +3110,34 @@ static struct omap_hwmod_ocp_if omap3xxx_l4_core__usb_tll_hs = {
 	.user		= OCP_USER_MPU | OCP_USER_SDMA,
 };
 
+/* l4_core -> hdq1w interface */
+static struct omap_hwmod_ocp_if omap3xxx_l4_core__hdq1w = {
+	.master		= &omap3xxx_l4_core_hwmod,
+	.slave		= &omap3xxx_hdq1w_hwmod,
+	.clk		= "hdq_ick",
+	.addr		= omap2_hdq1w_addr_space,
+	.user		= OCP_USER_MPU | OCP_USER_SDMA,
+	.flags		= OMAP_FIREWALL_L4 | OCPIF_SWSUP_IDLE,
+};
+
+/* l4_wkup -> 32ksync_counter */
+static struct omap_hwmod_addr_space omap3xxx_counter_32k_addrs[] = {
+	{
+		.pa_start	= 0x48320000,
+		.pa_end		= 0x4832001f,
+		.flags		= ADDR_TYPE_RT
+	},
+	{ }
+};
+
+static struct omap_hwmod_ocp_if omap3xxx_l4_wkup__counter_32k = {
+	.master		= &omap3xxx_l4_wkup_hwmod,
+	.slave		= &omap3xxx_counter_32k_hwmod,
+	.clk		= "omap_32ksync_ick",
+	.addr		= omap3xxx_counter_32k_addrs,
+	.user		= OCP_USER_MPU | OCP_USER_SDMA,
+};
+
 static struct omap_hwmod_ocp_if *omap3xxx_hwmod_ocp_ifs[] __initdata = {
 	&omap3xxx_l3_main__l4_core,
 	&omap3xxx_l3_main__l4_per,
@@ -3103,6 +3182,7 @@ static struct omap_hwmod_ocp_if *omap3xxx_hwmod_ocp_ifs[] __initdata = {
 	&omap34xx_l4_core__mcspi2,
 	&omap34xx_l4_core__mcspi3,
 	&omap34xx_l4_core__mcspi4,
+	&omap3xxx_l4_wkup__counter_32k,
 	NULL,
 };
 
@@ -3151,6 +3231,7 @@ static struct omap_hwmod_ocp_if *omap34xx_hwmod_ocp_ifs[] __initdata = {
 	&omap34xx_l4_core__sr1,
 	&omap34xx_l4_core__sr2,
 	&omap3xxx_l4_core__mailbox,
+	&omap3xxx_l4_core__hdq1w,
 	NULL
 };
 
@@ -3170,6 +3251,7 @@ static struct omap_hwmod_ocp_if *omap36xx_hwmod_ocp_ifs[] __initdata = {
 	&omap3xxx_l4_core__usb_tll_hs,
 	&omap3xxx_l4_core__es3plus_mmc1,
 	&omap3xxx_l4_core__es3plus_mmc2,
+	&omap3xxx_l4_core__hdq1w,
 	NULL
 };
 

arch/arm/mach-omap2/omap_hwmod_common_data.h

@@ -38,6 +38,7 @@ extern struct omap_hwmod_addr_space omap2430_mcspi3_addr_space[];
 extern struct omap_hwmod_addr_space omap2_dma_system_addrs[];
 extern struct omap_hwmod_addr_space omap2_mailbox_addrs[];
 extern struct omap_hwmod_addr_space omap2_mcbsp1_addrs[];
+extern struct omap_hwmod_addr_space omap2_hdq1w_addr_space[];
 
 /* Common IP block data across OMAP2xxx */
 extern struct omap_hwmod_irq_info omap2xxx_timer12_mpu_irqs[];
@@ -74,6 +75,7 @@ extern struct omap_hwmod omap2xxx_gpio3_hwmod;
 extern struct omap_hwmod omap2xxx_gpio4_hwmod;
 extern struct omap_hwmod omap2xxx_mcspi1_hwmod;
 extern struct omap_hwmod omap2xxx_mcspi2_hwmod;
+extern struct omap_hwmod omap2xxx_counter_32k_hwmod;
 
 /* Common interface data across OMAP2xxx */
 extern struct omap_hwmod_ocp_if omap2xxx_l3_main__l4_core;
@@ -141,6 +143,7 @@ extern struct omap_hwmod_irq_info omap2_dma_system_irqs[];
 extern struct omap_hwmod_irq_info omap2_mcspi1_mpu_irqs[];
 extern struct omap_hwmod_irq_info omap2_mcspi2_mpu_irqs[];
 extern struct omap_hwmod_addr_space omap2xxx_timer12_addrs[];
+extern struct omap_hwmod_irq_info omap2_hdq1w_mpu_irqs[];
 
 /* OMAP hwmod classes - forward declarations */
 extern struct omap_hwmod_class l3_hwmod_class;
@@ -152,6 +155,8 @@ extern struct omap_hwmod_class omap2_dss_hwmod_class;
 extern struct omap_hwmod_class omap2_dispc_hwmod_class;
 extern struct omap_hwmod_class omap2_rfbi_hwmod_class;
 extern struct omap_hwmod_class omap2_venc_hwmod_class;
+extern struct omap_hwmod_class_sysconfig omap2_hdq1w_sysc;
+extern struct omap_hwmod_class omap2_hdq1w_class;
 
 extern struct omap_hwmod_class omap2xxx_timer_hwmod_class;
 extern struct omap_hwmod_class omap2xxx_wd_timer_hwmod_class;

arch/arm/mach-omap2/powerdomain.c

@@ -981,16 +981,6 @@ int pwrdm_state_switch(struct powerdomain *pwrdm)
 	return ret;
 }
 
-int pwrdm_clkdm_state_switch(struct clockdomain *clkdm)
-{
-	if (clkdm != NULL && clkdm->pwrdm.ptr != NULL) {
-		pwrdm_wait_transition(clkdm->pwrdm.ptr);
-		return pwrdm_state_switch(clkdm->pwrdm.ptr);
-	}
-
-	return -EINVAL;
-}
-
 int pwrdm_pre_transition(void)
 {
 	pwrdm_for_each(_pwrdm_pre_transition_cb, NULL);

arch/arm/mach-omap2/powerdomain.h

@@ -213,7 +213,6 @@ bool pwrdm_has_hdwr_sar(struct powerdomain *pwrdm);
 int pwrdm_wait_transition(struct powerdomain *pwrdm);
 
 int pwrdm_state_switch(struct powerdomain *pwrdm);
-int pwrdm_clkdm_state_switch(struct clockdomain *clkdm);
 int pwrdm_pre_transition(void);
 int pwrdm_post_transition(void);
 int pwrdm_set_lowpwrstchange(struct powerdomain *pwrdm);

arch/arm/mach-omap2/prcm-common.h

@@ -177,6 +177,8 @@
 /* PM_WKST_WKUP, CM_IDLEST_WKUP shared bits */
 #define OMAP24XX_ST_GPIOS_SHIFT				2
 #define OMAP24XX_ST_GPIOS_MASK				(1 << 2)
+#define OMAP24XX_ST_32KSYNC_SHIFT			1
+#define OMAP24XX_ST_32KSYNC_MASK			(1 << 1)
 #define OMAP24XX_ST_GPT1_SHIFT				0
 #define OMAP24XX_ST_GPT1_MASK				(1 << 0)
 
@@ -307,6 +309,8 @@
 #define OMAP3430_ST_SR1_MASK				(1 << 6)
 #define OMAP3430_ST_GPIO1_SHIFT				3
 #define OMAP3430_ST_GPIO1_MASK				(1 << 3)
+#define OMAP3430_ST_32KSYNC_SHIFT			2
+#define OMAP3430_ST_32KSYNC_MASK			(1 << 2)
 #define OMAP3430_ST_GPT12_SHIFT				1
 #define OMAP3430_ST_GPT12_MASK				(1 << 1)
 #define OMAP3430_ST_GPT1_SHIFT				0
@@ -410,6 +414,19 @@
 extern void __iomem *prm_base;
 extern void __iomem *cm_base;
 extern void __iomem *cm2_base;
+extern void __iomem *prcm_mpu_base;
+
+#if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_ARCH_OMAP5)
+extern void omap_prm_base_init(void);
+extern void omap_cm_base_init(void);
+#else
+static inline void omap_prm_base_init(void)
+{
+}
+static inline void omap_cm_base_init(void)
+{
+}
+#endif
 
 /**
  * struct omap_prcm_irq - describes a PRCM interrupt bit

arch/arm/mach-omap2/prcm.c

@@ -42,6 +42,7 @@
 void __iomem *prm_base;
 void __iomem *cm_base;
 void __iomem *cm2_base;
+void __iomem *prcm_mpu_base;
 
 #define MAX_MODULE_ENABLE_WAIT		100000
 
@@ -155,4 +156,11 @@ void __init omap2_set_globals_prcm(struct omap_globals *omap2_globals)
 		cm_base = omap2_globals->cm;
 	if (omap2_globals->cm2)
 		cm2_base = omap2_globals->cm2;
+	if (omap2_globals->prcm_mpu)
+		prcm_mpu_base = omap2_globals->prcm_mpu;
+
+	if (cpu_is_omap44xx()) {
+		omap_prm_base_init();
+		omap_cm_base_init();
+	}
 }

arch/arm/mach-omap2/prminst44xx.c

@@ -18,20 +18,26 @@
 
 #include "iomap.h"
 #include "common.h"
+#include "prcm-common.h"
 #include "prm44xx.h"
 #include "prminst44xx.h"
 #include "prm-regbits-44xx.h"
 #include "prcm44xx.h"
 #include "prcm_mpu44xx.h"
 
-static u32 _prm_bases[OMAP4_MAX_PRCM_PARTITIONS] = {
-	[OMAP4430_INVALID_PRCM_PARTITION]	= 0,
-	[OMAP4430_PRM_PARTITION]		= OMAP4430_PRM_BASE,
-	[OMAP4430_CM1_PARTITION]		= 0,
-	[OMAP4430_CM2_PARTITION]		= 0,
-	[OMAP4430_SCRM_PARTITION]		= 0,
-	[OMAP4430_PRCM_MPU_PARTITION]		= OMAP4430_PRCM_MPU_BASE,
-};
+static void __iomem *_prm_bases[OMAP4_MAX_PRCM_PARTITIONS];
+
+/**
+ * omap_prm_base_init - Populates the prm partitions
+ *
+ * Populates the base addresses of the _prm_bases
+ * array used for read/write of prm module registers.
+ */
+void omap_prm_base_init(void)
+{
+	_prm_bases[OMAP4430_PRM_PARTITION] = prm_base;
+	_prm_bases[OMAP4430_PRCM_MPU_PARTITION] = prcm_mpu_base;
+}
 
 /* Read a register in a PRM instance */
 u32 omap4_prminst_read_inst_reg(u8 part, s16 inst, u16 idx)
@@ -39,8 +45,7 @@ u32 omap4_prminst_read_inst_reg(u8 part, s16 inst, u16 idx)
 	BUG_ON(part >= OMAP4_MAX_PRCM_PARTITIONS ||
 	       part == OMAP4430_INVALID_PRCM_PARTITION ||
 	       !_prm_bases[part]);
-	return __raw_readl(OMAP2_L4_IO_ADDRESS(_prm_bases[part] + inst +
-					       idx));
+	return __raw_readl(_prm_bases[part] + inst + idx);
 }
 
 /* Write into a register in a PRM instance */
@@ -49,7 +54,7 @@ void omap4_prminst_write_inst_reg(u32 val, u8 part, s16 inst, u16 idx)
 	BUG_ON(part >= OMAP4_MAX_PRCM_PARTITIONS ||
 	       part == OMAP4430_INVALID_PRCM_PARTITION ||
 	       !_prm_bases[part]);
-	__raw_writel(val, OMAP2_L4_IO_ADDRESS(_prm_bases[part] + inst + idx));
+	__raw_writel(val, _prm_bases[part] + inst + idx);
 }
 
 /* Read-modify-write a register in PRM. Caller must lock */

arch/arm/mach-omap2/timer.c

@@ -178,13 +178,6 @@ static int __init omap_dm_timer_init_one(struct omap_dm_timer *timer,
 	if (IS_ERR(timer->fclk))
 		return -ENODEV;
 
-	sprintf(name, "gpt%d_ick", gptimer_id);
-	timer->iclk = clk_get(NULL, name);
-	if (IS_ERR(timer->iclk)) {
-		clk_put(timer->fclk);
-		return -ENODEV;
-	}
-
 	omap_hwmod_enable(oh);
 
 	sys_timer_reserved |= (1 << (gptimer_id - 1));

arch/arm/mach-omap2/twl-common.c

@@ -31,6 +31,7 @@
 
 #include "twl-common.h"
 #include "pm.h"
+#include "voltage.h"
 
 static struct i2c_board_info __initdata pmic_i2c_board_info = {
 	.addr		= 0x48,
@@ -47,6 +48,18 @@ static struct i2c_board_info __initdata omap4_i2c1_board_info[] = {
 	},
 };
 
+static int twl_set_voltage(void *data, int target_uV)
+{
+	struct voltagedomain *voltdm = (struct voltagedomain *)data;
+	return voltdm_scale(voltdm, target_uV);
+}
+
+static int twl_get_voltage(void *data)
+{
+	struct voltagedomain *voltdm = (struct voltagedomain *)data;
+	return voltdm_get_voltage(voltdm);
+}
+
 void __init omap_pmic_init(int bus, u32 clkrate,
 			   const char *pmic_type, int pmic_irq,
 			   struct twl4030_platform_data *pmic_data)
@@ -153,6 +166,48 @@ static struct regulator_init_data omap3_vpll2_idata = {
 	.consumer_supplies		= omap3_vpll2_supplies,
 };
 
+static struct regulator_consumer_supply omap3_vdd1_supply[] = {
+	REGULATOR_SUPPLY("vcc", "mpu.0"),
+};
+
+static struct regulator_consumer_supply omap3_vdd2_supply[] = {
+	REGULATOR_SUPPLY("vcc", "l3_main.0"),
+};
+
+static struct regulator_init_data omap3_vdd1 = {
+	.constraints = {
+		.name			= "vdd_mpu_iva",
+		.min_uV			= 600000,
+		.max_uV			= 1450000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE,
+	},
+	.num_consumer_supplies		= ARRAY_SIZE(omap3_vdd1_supply),
+	.consumer_supplies		= omap3_vdd1_supply,
+};
+
+static struct regulator_init_data omap3_vdd2 = {
+	.constraints = {
+		.name			= "vdd_core",
+		.min_uV			= 600000,
+		.max_uV			= 1450000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE,
+	},
+	.num_consumer_supplies		= ARRAY_SIZE(omap3_vdd2_supply),
+	.consumer_supplies		= omap3_vdd2_supply,
+};
+
+static struct twl_regulator_driver_data omap3_vdd1_drvdata = {
+	.get_voltage = twl_get_voltage,
+	.set_voltage = twl_set_voltage,
+};
+
+static struct twl_regulator_driver_data omap3_vdd2_drvdata = {
+	.get_voltage = twl_get_voltage,
+	.set_voltage = twl_set_voltage,
+};
+
 void __init omap3_pmic_get_config(struct twl4030_platform_data *pmic_data,
 				  u32 pdata_flags, u32 regulators_flags)
 {
@@ -160,6 +215,16 @@ void __init omap3_pmic_get_config(struct twl4030_platform_data *pmic_data,
 		pmic_data->irq_base = TWL4030_IRQ_BASE;
 	if (!pmic_data->irq_end)
 		pmic_data->irq_end = TWL4030_IRQ_END;
+	if (!pmic_data->vdd1) {
+		omap3_vdd1.driver_data = &omap3_vdd1_drvdata;
+		omap3_vdd1_drvdata.data = voltdm_lookup("mpu_iva");
+		pmic_data->vdd1 = &omap3_vdd1;
+	}
+	if (!pmic_data->vdd2) {
+		omap3_vdd2.driver_data = &omap3_vdd2_drvdata;
+		omap3_vdd2_drvdata.data = voltdm_lookup("core");
+		pmic_data->vdd2 = &omap3_vdd2;
+	}
 
 	/* Common platform data configurations */
 	if (pdata_flags & TWL_COMMON_PDATA_USB && !pmic_data->usb)
@@ -310,6 +375,70 @@ static struct regulator_init_data omap4_clk32kg_idata = {
 	},
 };
 
+static struct regulator_consumer_supply omap4_vdd1_supply[] = {
+	REGULATOR_SUPPLY("vcc", "mpu.0"),
+};
+
+static struct regulator_consumer_supply omap4_vdd2_supply[] = {
+	REGULATOR_SUPPLY("vcc", "iva.0"),
+};
+
+static struct regulator_consumer_supply omap4_vdd3_supply[] = {
+	REGULATOR_SUPPLY("vcc", "l3_main.0"),
+};
+
+static struct regulator_init_data omap4_vdd1 = {
+	.constraints = {
+		.name			= "vdd_mpu",
+		.min_uV			= 500000,
+		.max_uV			= 1500000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE,
+	},
+	.num_consumer_supplies		= ARRAY_SIZE(omap4_vdd1_supply),
+	.consumer_supplies		= omap4_vdd1_supply,
+};
+
+static struct regulator_init_data omap4_vdd2 = {
+	.constraints = {
+		.name			= "vdd_iva",
+		.min_uV			= 500000,
+		.max_uV			= 1500000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE,
+	},
+	.num_consumer_supplies		= ARRAY_SIZE(omap4_vdd2_supply),
+	.consumer_supplies		= omap4_vdd2_supply,
+};
+
+static struct regulator_init_data omap4_vdd3 = {
+	.constraints = {
+		.name			= "vdd_core",
+		.min_uV			= 500000,
+		.max_uV			= 1500000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE,
+	},
+	.num_consumer_supplies		= ARRAY_SIZE(omap4_vdd3_supply),
+	.consumer_supplies		= omap4_vdd3_supply,
+};
+
+
+static struct twl_regulator_driver_data omap4_vdd1_drvdata = {
+	.get_voltage = twl_get_voltage,
+	.set_voltage = twl_set_voltage,
+};
+
+static struct twl_regulator_driver_data omap4_vdd2_drvdata = {
+	.get_voltage = twl_get_voltage,
+	.set_voltage = twl_set_voltage,
+};
+
+static struct twl_regulator_driver_data omap4_vdd3_drvdata = {
+	.get_voltage = twl_get_voltage,
+	.set_voltage = twl_set_voltage,
+};
+
 void __init omap4_pmic_get_config(struct twl4030_platform_data *pmic_data,
 				  u32 pdata_flags, u32 regulators_flags)
 {
@@ -318,6 +447,24 @@ void __init omap4_pmic_get_config(struct twl4030_platform_data *pmic_data,
 	if (!pmic_data->irq_end)
 		pmic_data->irq_end = TWL6030_IRQ_END;
 
+	if (!pmic_data->vdd1) {
+		omap4_vdd1.driver_data = &omap4_vdd1_drvdata;
+		omap4_vdd1_drvdata.data = voltdm_lookup("mpu");
+		pmic_data->vdd1 = &omap4_vdd1;
+	}
+
+	if (!pmic_data->vdd2) {
+		omap4_vdd2.driver_data = &omap4_vdd2_drvdata;
+		omap4_vdd2_drvdata.data = voltdm_lookup("iva");
+		pmic_data->vdd2 = &omap4_vdd2;
+	}
+
+	if (!pmic_data->vdd3) {
+		omap4_vdd3.driver_data = &omap4_vdd3_drvdata;
+		omap4_vdd3_drvdata.data = voltdm_lookup("core");
+		pmic_data->vdd3 = &omap4_vdd3;
+	}
+
 	/* Common platform data configurations */
 	if (pdata_flags & TWL_COMMON_PDATA_USB && !pmic_data->usb)
 		pmic_data->usb = &omap4_usb_pdata;

arch/arm/mach-omap2/vc3xxx_data.c

@@ -46,6 +46,7 @@ static struct omap_vc_common omap3_vc_common = {
 };
 
 struct omap_vc_channel omap3_vc_mpu = {
+	.flags = OMAP_VC_CHANNEL_DEFAULT,
 	.common = &omap3_vc_common,
 	.smps_sa_reg	 = OMAP3_PRM_VC_SMPS_SA_OFFSET,
 	.smps_volra_reg	 = OMAP3_PRM_VC_SMPS_VOL_RA_OFFSET,

arch/arm/mach-omap2/voltage.c

@@ -73,7 +73,8 @@ unsigned long voltdm_get_voltage(struct voltagedomain *voltdm)
 int voltdm_scale(struct voltagedomain *voltdm,
 		 unsigned long target_volt)
 {
-	int ret;
+	int ret, i;
+	unsigned long volt = 0;
 
 	if (!voltdm || IS_ERR(voltdm)) {
 		pr_warning("%s: VDD specified does not exist!\n", __func__);
@@ -86,9 +87,23 @@ int voltdm_scale(struct voltagedomain *voltdm,
 		return -ENODATA;
 	}
 
-	ret = voltdm->scale(voltdm, target_volt);
+	/* Adjust voltage to the exact voltage from the OPP table */
+	for (i = 0; voltdm->volt_data[i].volt_nominal != 0; i++) {
+		if (voltdm->volt_data[i].volt_nominal >= target_volt) {
+			volt = voltdm->volt_data[i].volt_nominal;
+			break;
+		}
+	}
+
+	if (!volt) {
+		pr_warning("%s: not scaling. OPP voltage for %lu, not found.\n",
+			   __func__, target_volt);
+		return -EINVAL;
+	}
+
+	ret = voltdm->scale(voltdm, volt);
 	if (!ret)
-		voltdm->nominal_volt = target_volt;
+		voltdm->nominal_volt = volt;
 
 	return ret;
 }

arch/arm/mach-omap2/wd_timer.c

@@ -14,6 +14,7 @@
 #include <plat/omap_hwmod.h>
 
 #include "wd_timer.h"
+#include "common.h"
 
 /*
  * In order to avoid any assumptions from bootloader regarding WDT
@@ -25,6 +26,8 @@
 #define OMAP_WDT_WPS		0x34
 #define OMAP_WDT_SPR		0x48
 
+/* Maximum microseconds to wait for OMAP module to softreset */
+#define MAX_MODULE_SOFTRESET_WAIT	10000
 
 int omap2_wd_timer_disable(struct omap_hwmod *oh)
 {
@@ -54,3 +57,45 @@ int omap2_wd_timer_disable(struct omap_hwmod *oh)
 	return 0;
 }
 
+/**
+ * omap2_wdtimer_reset - reset and disable the WDTIMER IP block
+ * @oh: struct omap_hwmod *
+ *
+ * After the WDTIMER IP blocks are reset on OMAP2/3, we must also take
+ * care to execute the special watchdog disable sequence.  This is
+ * because the watchdog is re-armed upon OCP softreset.  (On OMAP4,
+ * this behavior was apparently changed and the watchdog is no longer
+ * re-armed after an OCP soft-reset.)  Returns -ETIMEDOUT if the reset
+ * did not complete, or 0 upon success.
+ *
+ * XXX Most of this code should be moved to the omap_hwmod.c layer
+ * during a normal merge window.  omap_hwmod_softreset() should be
+ * renamed to omap_hwmod_set_ocp_softreset(), and omap_hwmod_softreset()
+ * should call the hwmod _ocp_softreset() code.
+ */
+int omap2_wd_timer_reset(struct omap_hwmod *oh)
+{
+	int c = 0;
+
+	/* Write to the SOFTRESET bit */
+	omap_hwmod_softreset(oh);
+
+	/* Poll on RESETDONE bit */
+	omap_test_timeout((omap_hwmod_read(oh,
+					   oh->class->sysc->syss_offs)
+			   & SYSS_RESETDONE_MASK),
+			  MAX_MODULE_SOFTRESET_WAIT, c);
+
+	if (oh->class->sysc->srst_udelay)
+		udelay(oh->class->sysc->srst_udelay);
+
+	if (c == MAX_MODULE_SOFTRESET_WAIT)
+		pr_warning("%s: %s: softreset failed (waited %d usec)\n",
+			   __func__, oh->name, MAX_MODULE_SOFTRESET_WAIT);
+	else
+		pr_debug("%s: %s: softreset in %d usec\n", __func__,
+			 oh->name, c);
+
+	return (c == MAX_MODULE_SOFTRESET_WAIT) ? -ETIMEDOUT :
+		omap2_wd_timer_disable(oh);
+}

arch/arm/mach-omap2/wd_timer.h

@@ -13,5 +13,6 @@
 #include <plat/omap_hwmod.h>
 
 extern int omap2_wd_timer_disable(struct omap_hwmod *oh);
+extern int omap2_wd_timer_reset(struct omap_hwmod *oh);
 
 #endif

arch/arm/mach-ux500/Makefile

@@ -4,6 +4,7 @@
 
 obj-y				:= clock.o cpu.o devices.o devices-common.o \
 				   id.o usb.o timer.o
+obj-$(CONFIG_CPU_IDLE)          += cpuidle.o
 obj-$(CONFIG_CACHE_L2X0)	+= cache-l2x0.o
 obj-$(CONFIG_UX500_SOC_DB8500)	+= cpu-db8500.o devices-db8500.o
 obj-$(CONFIG_MACH_MOP500)	+= board-mop500.o board-mop500-sdi.o \

arch/arm/mach-ux500/cpuidle.c

+/*
+ * Copyright (c) 2012 Linaro : Daniel Lezcano <daniel.lezcano@linaro.org> (IBM)
+ *
+ * Based on the work of Rickard Andersson <rickard.andersson@stericsson.com>
+ * and Jonas Aaberg <jonas.aberg@stericsson.com>.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/cpuidle.h>
+#include <linux/clockchips.h>
+#include <linux/spinlock.h>
+#include <linux/atomic.h>
+#include <linux/smp.h>
+#include <linux/mfd/dbx500-prcmu.h>
+
+#include <asm/cpuidle.h>
+#include <asm/proc-fns.h>
+
+static atomic_t master = ATOMIC_INIT(0);
+static DEFINE_SPINLOCK(master_lock);
+static DEFINE_PER_CPU(struct cpuidle_device, ux500_cpuidle_device);
+
+static inline int ux500_enter_idle(struct cpuidle_device *dev,
+				   struct cpuidle_driver *drv, int index)
+{
+	int this_cpu = smp_processor_id();
+	bool recouple = false;
+
+	clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ENTER, &this_cpu);
+
+	if (atomic_inc_return(&master) == num_online_cpus()) {
+
+		/* With this lock, we prevent the other cpu to exit and enter
+		 * this function again and become the master */
+		if (!spin_trylock(&master_lock))
+			goto wfi;
+
+		/* decouple the gic from the A9 cores */
+		if (prcmu_gic_decouple())
+			goto out;
+
+		/* If an error occur, we will have to recouple the gic
+		 * manually */
+		recouple = true;
+
+		/* At this state, as the gic is decoupled, if the other
+		 * cpu is in WFI, we have the guarantee it won't be wake
+		 * up, so we can safely go to retention */
+		if (!prcmu_is_cpu_in_wfi(this_cpu ? 0 : 1))
+			goto out;
+
+		/* The prcmu will be in charge of watching the interrupts
+		 * and wake up the cpus */
+		if (prcmu_copy_gic_settings())
+			goto out;
+
+		/* Check in the meantime an interrupt did
+		 * not occur on the gic ... */
+		if (prcmu_gic_pending_irq())
+			goto out;
+
+		/* ... and the prcmu */
+		if (prcmu_pending_irq())
+			goto out;
+
+		/* Go to the retention state, the prcmu will wait for the
+		 * cpu to go WFI and this is what happens after exiting this
+		 * 'master' critical section */
+		if (prcmu_set_power_state(PRCMU_AP_IDLE, true, true))
+			goto out;
+
+		/* When we switch to retention, the prcmu is in charge
+		 * of recoupling the gic automatically */
+		recouple = false;
+
+		spin_unlock(&master_lock);
+	}
+wfi:
+	cpu_do_idle();
+out:
+	atomic_dec(&master);
+
+	if (recouple) {
+		prcmu_gic_recouple();
+		spin_unlock(&master_lock);
+	}
+
+	clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_EXIT, &this_cpu);
+
+	return index;
+}
+
+static struct cpuidle_driver ux500_idle_driver = {
+	.name = "ux500_idle",
+	.owner = THIS_MODULE,
+	.en_core_tk_irqen = 1,
+	.states = {
+		ARM_CPUIDLE_WFI_STATE,
+		{
+			.enter		  = ux500_enter_idle,
+			.exit_latency	  = 70,
+			.target_residency = 260,
+			.flags		  = CPUIDLE_FLAG_TIME_VALID,
+			.name		  = "ApIdle",
+			.desc		  = "ARM Retention",
+		},
+	},
+	.safe_state_index = 0,
+	.state_count = 2,
+};
+
+/*
+ * For each cpu, setup the broadcast timer because we will
+ * need to migrate the timers for the states >= ApIdle.
+ */
+static void ux500_setup_broadcast_timer(void *arg)
+{
+	int cpu = smp_processor_id();
+	clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ON, &cpu);
+}
+
+int __init ux500_idle_init(void)
+{
+	int ret, cpu;
+	struct cpuidle_device *device;
+
+        /* Configure wake up reasons */
+	prcmu_enable_wakeups(PRCMU_WAKEUP(ARM) | PRCMU_WAKEUP(RTC) |
+			     PRCMU_WAKEUP(ABB));
+
+	/*
+	 * Configure the timer broadcast for each cpu, that must
+	 * be done from the cpu context, so we use a smp cross
+	 * call with 'on_each_cpu'.
+	 */
+	on_each_cpu(ux500_setup_broadcast_timer, NULL, 1);
+
+	ret = cpuidle_register_driver(&ux500_idle_driver);
+	if (ret) {
+		printk(KERN_ERR "failed to register ux500 idle driver\n");
+		return ret;
+	}
+
+	for_each_online_cpu(cpu) {
+		device = &per_cpu(ux500_cpuidle_device, cpu);
+		device->cpu = cpu;
+		ret = cpuidle_register_device(device);
+		if (ret) {
+			printk(KERN_ERR "Failed to register cpuidle "
+			       "device for cpu%d\n", cpu);
+			goto out_unregister;
+		}
+	}
+out:
+	return ret;
+
+out_unregister:
+	for_each_online_cpu(cpu) {
+		device = &per_cpu(ux500_cpuidle_device, cpu);
+		cpuidle_unregister_device(device);
+	}
+
+	cpuidle_unregister_driver(&ux500_idle_driver);
+	goto out;
+}
+
+device_initcall(ux500_idle_init);

arch/arm/mm/cache-tauros2.c

@@ -108,6 +108,26 @@ static void tauros2_flush_range(unsigned long start, unsigned long end)
 
 	dsb();
 }
+
+static void tauros2_disable(void)
+{
+	__asm__ __volatile__ (
+	"mcr	p15, 1, %0, c7, c11, 0 @L2 Cache Clean All\n\t"
+	"mrc	p15, 0, %0, c1, c0, 0\n\t"
+	"bic	%0, %0, #(1 << 26)\n\t"
+	"mcr	p15, 0, %0, c1, c0, 0  @Disable L2 Cache\n\t"
+	: : "r" (0x0));
+}
+
+static void tauros2_resume(void)
+{
+	__asm__ __volatile__ (
+	"mcr	p15, 1, %0, c7, c7, 0 @L2 Cache Invalidate All\n\t"
+	"mrc	p15, 0, %0, c1, c0, 0\n\t"
+	"orr	%0, %0, #(1 << 26)\n\t"
+	"mcr	p15, 0, %0, c1, c0, 0 @Enable L2 Cache\n\t"
+	: : "r" (0x0));
+}
 #endif
 
 static inline u32 __init read_extra_features(void)
@@ -194,6 +214,8 @@ void __init tauros2_init(void)
 		outer_cache.inv_range = tauros2_inv_range;
 		outer_cache.clean_range = tauros2_clean_range;
 		outer_cache.flush_range = tauros2_flush_range;
+		outer_cache.disable = tauros2_disable;
+		outer_cache.resume = tauros2_resume;
 	}
 #endif
 
@@ -219,6 +241,8 @@ void __init tauros2_init(void)
 		outer_cache.inv_range = tauros2_inv_range;
 		outer_cache.clean_range = tauros2_clean_range;
 		outer_cache.flush_range = tauros2_flush_range;
+		outer_cache.disable = tauros2_disable;
+		outer_cache.resume = tauros2_resume;
 	}
 #endif
 

arch/arm/mm/proc-mohawk.S

@@ -345,6 +345,41 @@ ENTRY(cpu_mohawk_set_pte_ext)
 	mcr	p15, 0, r0, c7, c10, 4		@ drain WB
 	mov	pc, lr
 
+.globl	cpu_mohawk_suspend_size
+.equ	cpu_mohawk_suspend_size, 4 * 6
+#ifdef CONFIG_PM_SLEEP
+ENTRY(cpu_mohawk_do_suspend)
+	stmfd	sp!, {r4 - r9, lr}
+	mrc	p14, 0, r4, c6, c0, 0	@ clock configuration, for turbo mode
+	mrc	p15, 0, r5, c15, c1, 0	@ CP access reg
+	mrc	p15, 0, r6, c13, c0, 0	@ PID
+	mrc 	p15, 0, r7, c3, c0, 0	@ domain ID
+	mrc	p15, 0, r8, c1, c0, 1	@ auxiliary control reg
+	mrc 	p15, 0, r9, c1, c0, 0	@ control reg
+	bic	r4, r4, #2		@ clear frequency change bit
+	stmia	r0, {r4 - r9}		@ store cp regs
+	ldmia	sp!, {r4 - r9, pc}
+ENDPROC(cpu_mohawk_do_suspend)
+
+ENTRY(cpu_mohawk_do_resume)
+	ldmia	r0, {r4 - r9}		@ load cp regs
+	mov	ip, #0
+	mcr	p15, 0, ip, c7, c7, 0	@ invalidate I & D caches, BTB
+	mcr	p15, 0, ip, c7, c10, 4	@ drain write (&fill) buffer
+	mcr	p15, 0, ip, c7, c5, 4	@ flush prefetch buffer
+	mcr	p15, 0, ip, c8, c7, 0	@ invalidate I & D TLBs
+	mcr	p14, 0, r4, c6, c0, 0	@ clock configuration, turbo mode.
+	mcr	p15, 0, r5, c15, c1, 0	@ CP access reg
+	mcr	p15, 0, r6, c13, c0, 0	@ PID
+	mcr	p15, 0, r7, c3, c0, 0	@ domain ID
+	orr	r1, r1, #0x18		@ cache the page table in L2
+	mcr	p15, 0, r1, c2, c0, 0	@ translation table base addr
+	mcr	p15, 0, r8, c1, c0, 1	@ auxiliary control reg
+	mov	r0, r9			@ control register
+	b	cpu_resume_mmu
+ENDPROC(cpu_mohawk_do_resume)
+#endif
+
 	__CPUINIT
 
 	.type	__mohawk_setup, #function

arch/arm/plat-omap/include/plat/clkdev_omap.h

@@ -34,8 +34,7 @@ struct omap_clk {
 #define CK_243X		(1 << 5)	/* 243x, 253x */
 #define CK_3430ES1	(1 << 6)	/* 34xxES1 only */
 #define CK_3430ES2PLUS	(1 << 7)	/* 34xxES2, ES3, non-Sitara 35xx only */
-#define CK_3505		(1 << 8)
-#define CK_3517		(1 << 9)
+#define CK_AM35XX	(1 << 9)	/* Sitara AM35xx */
 #define CK_36XX		(1 << 10)	/* 36xx/37xx-specific clocks */
 #define CK_443X		(1 << 11)
 #define CK_TI816X	(1 << 12)
@@ -44,7 +43,6 @@ struct omap_clk {
 
 
 #define CK_34XX		(CK_3430ES1 | CK_3430ES2PLUS)
-#define CK_AM35XX	(CK_3505 | CK_3517)	/* all Sitara AM35xx */
 #define CK_3XXX		(CK_34XX | CK_AM35XX | CK_36XX)
 
 

arch/arm/plat-omap/include/plat/dmtimer.h

@@ -259,7 +259,7 @@ struct omap_dm_timer {
 	unsigned long phys_base;
 	int id;
 	int irq;
-	struct clk *iclk, *fclk;
+	struct clk *fclk;
 
 	void __iomem	*io_base;
 	void __iomem	*sys_stat;	/* TISTAT timer status */

arch/arm/plat-omap/include/plat/hdq1w.h

+/*
+ * Shared macros and function prototypes for the HDQ1W/1-wire IP block
+ *
+ * Copyright (C) 2012 Texas Instruments, Inc.
+ * Paul Walmsley
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ */
+#ifndef ARCH_ARM_MACH_OMAP2_HDQ1W_H
+#define ARCH_ARM_MACH_OMAP2_HDQ1W_H
+
+#include <plat/omap_hwmod.h>
+
+/*
+ * XXX A future cleanup patch should modify
+ * drivers/w1/masters/omap_hdq.c to use these macros
+ */
+#define HDQ_CTRL_STATUS_OFFSET			0x0c
+#define HDQ_CTRL_STATUS_CLOCKENABLE_SHIFT	5
+
+
+extern int omap_hdq1w_reset(struct omap_hwmod *oh);
+
+#endif

arch/arm/plat-omap/include/plat/mmc.h

@@ -16,6 +16,7 @@
 #include <linux/mmc/host.h>
 
 #include <plat/board.h>
+#include <plat/omap_hwmod.h>
 
 #define OMAP15XX_NR_MMC		1
 #define OMAP16XX_NR_MMC		2
@@ -195,4 +196,7 @@ static inline int omap_mmc_add(const char *name, int id, unsigned long base,
 }
 
 #endif
+
+extern int omap_msdi_reset(struct omap_hwmod *oh);
+
 #endif

arch/arm/plat-omap/include/plat/omap_hwmod.h

@@ -214,6 +214,7 @@ struct omap_hwmod_addr_space {
 #define OCP_USER_MPU			(1 << 0)
 #define OCP_USER_SDMA			(1 << 1)
 #define OCP_USER_DSP			(1 << 2)
+#define OCP_USER_IVA			(1 << 3)
 
 /* omap_hwmod_ocp_if.flags bits */
 #define OCPIF_SWSUP_IDLE		(1 << 0)