Merge tag 'reset-for-v5.20' of git://git.pengutronix.de/pza/linux into arm/late

Reset controller updates for v5.20

Allow reset-simple to be selected under EXPERT and reset-a10sr to be
built under COMPILE_TEST. Add Renesas RZ/G2UL USBPHY binding and a new
driver for the TI TPS380x line of voltage supervisor ICs with manual
reset control.

A patch to make reset-microchip-sparx5 buildable as a module had to be
reverted as that turned out to break MDIO on kswitch-d10.

* tag 'reset-for-v5.20' of git://git.pengutronix.de/pza/linux:
  reset: tps380x: Fix spelling mistake "Voltags" -> "Voltage"
  reset: tps380x: Add TPS380x device driver supprt
  dt-bindings: reset: Add TPS380x documentation
  dt-bindings: reset: renesas,rzg2l-usbphy-ctrl: Document RZ/G2UL USBPHY Control bindings
  reset: reset-simple should depends on HAS_IOMEM
  Revert "reset: microchip-sparx5: allow building as a module"
  reset: a10sr: allow building under COMPILE_TEST
  reset: allow building of reset simple driver if expert config selected
  reset: microchip-sparx5: allow building as a module

Link: https://lore.kernel.org/r/20220729133620.488379-1-p.zabel@pengutronix.deSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/reset/renesas,rzg2l-usbphy-ctrl.yaml

@@ -17,6 +17,7 @@ properties:
   compatible:
     items:
       - enum:
+          - renesas,r9a07g043-usbphy-ctrl # RZ/G2UL
           - renesas,r9a07g044-usbphy-ctrl # RZ/G2{L,LC}
           - renesas,r9a07g054-usbphy-ctrl # RZ/V2L
       - const: renesas,rzg2l-usbphy-ctrl

Documentation/devicetree/bindings/reset/ti,tps380x-reset.yaml

+# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/reset/ti,tps380x-reset.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI TPS380x reset controller node bindings
+
+maintainers:
+  - Marco Felsch <kernel@pengutronix.de>
+
+description: |
+  The TPS380x family [1] of supervisory circuits monitor supply voltages to
+  provide circuit initialization and timing supervision. The devices assert a
+  RESET signal if the voltage drops below a preset threshold or upon a manual
+  reset input (MR). The RESET output remains asserted for the factory
+  programmed delay after the voltage return above its threshold or after the
+  manual reset input is released.
+
+  [1] https://www.ti.com/product/TPS3801
+
+properties:
+  compatible:
+    enum:
+      - ti,tps3801
+
+  reset-gpios:
+    maxItems: 1
+    description: Reference to the GPIO connected to the MR pin.
+
+  "#reset-cells":
+    const: 0
+
+required:
+  - compatible
+  - reset-gpios
+  - "#reset-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    reset: reset-controller {
+        compatible = "ti,tps3801";
+        #reset-cells = <0>;
+        reset-gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
+    };
+...

drivers/reset/Kconfig

@@ -17,7 +17,7 @@ if RESET_CONTROLLER
 
 config RESET_A10SR
 	tristate "Altera Arria10 System Resource Reset"
-	depends on MFD_ALTERA_A10SR
+	depends on MFD_ALTERA_A10SR || COMPILE_TEST
 	help
 	  This option enables support for the external reset functions for
 	  peripheral PHYs on the Altera Arria10 System Resource Chip.
@@ -200,8 +200,9 @@ config RESET_SCMI
 	  firmware controlling all the reset signals.
 
 config RESET_SIMPLE
-	bool "Simple Reset Controller Driver" if COMPILE_TEST
+	bool "Simple Reset Controller Driver" if COMPILE_TEST || EXPERT
 	default ARCH_ASPEED || ARCH_BCM4908 || ARCH_BITMAIN || ARCH_REALTEK || ARCH_STM32 || (ARCH_INTEL_SOCFPGA && ARM64) || ARCH_SUNXI || ARC
+	depends on HAS_IOMEM
 	help
 	  This enables a simple reset controller driver for reset lines that
 	  that can be asserted and deasserted by toggling bits in a contiguous,
@@ -256,6 +257,14 @@ config RESET_TI_SYSCON
 	  you wish to use the reset framework for such memory-mapped devices,
 	  say Y here. Otherwise, say N.
 
+config RESET_TI_TPS380X
+	tristate "TI TPS380x Reset Driver"
+	select GPIOLIB
+	help
+	  This enables the reset driver support for TI TPS380x devices. If
+	  you wish to use the reset framework for such devices, say Y here.
+	  Otherwise, say N.
+
 config RESET_TN48M_CPLD
 	tristate "Delta Networks TN48M switch CPLD reset controller"
 	depends on MFD_TN48M_CPLD || COMPILE_TEST

drivers/reset/Makefile

@@ -33,6 +33,7 @@ obj-$(CONFIG_RESET_STARFIVE_JH7100) += reset-starfive-jh7100.o
 obj-$(CONFIG_RESET_SUNXI) += reset-sunxi.o
 obj-$(CONFIG_RESET_TI_SCI) += reset-ti-sci.o
 obj-$(CONFIG_RESET_TI_SYSCON) += reset-ti-syscon.o
+obj-$(CONFIG_RESET_TI_TPS380X) += reset-tps380x.o
 obj-$(CONFIG_RESET_TN48M_CPLD) += reset-tn48m.o
 obj-$(CONFIG_RESET_UNIPHIER) += reset-uniphier.o
 obj-$(CONFIG_RESET_UNIPHIER_GLUE) += reset-uniphier-glue.o

drivers/reset/reset-tps380x.c

+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * TI TPS380x Supply Voltage Supervisor and Reset Controller Driver
+ *
+ * Copyright (C) 2022 Pengutronix, Marco Felsch <kernel@pengutronix.de>
+ *
+ * Based on Simple Reset Controller Driver
+ *
+ * Copyright (C) 2017 Pengutronix, Philipp Zabel <kernel@pengutronix.de>
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/reset-controller.h>
+
+struct tps380x_reset {
+	struct reset_controller_dev	rcdev;
+	struct gpio_desc		*reset_gpio;
+	unsigned int			reset_ms;
+};
+
+struct tps380x_reset_devdata {
+	unsigned int min_reset_ms;
+	unsigned int typ_reset_ms;
+	unsigned int max_reset_ms;
+};
+
+static inline
+struct tps380x_reset *to_tps380x_reset(struct reset_controller_dev *rcdev)
+{
+	return container_of(rcdev, struct tps380x_reset, rcdev);
+}
+
+static int
+tps380x_reset_assert(struct reset_controller_dev *rcdev, unsigned long id)
+{
+	struct tps380x_reset *tps380x = to_tps380x_reset(rcdev);
+
+	gpiod_set_value_cansleep(tps380x->reset_gpio, 1);
+
+	return 0;
+}
+
+static int
+tps380x_reset_deassert(struct reset_controller_dev *rcdev, unsigned long id)
+{
+	struct tps380x_reset *tps380x = to_tps380x_reset(rcdev);
+
+	gpiod_set_value_cansleep(tps380x->reset_gpio, 0);
+	msleep(tps380x->reset_ms);
+
+	return 0;
+}
+
+static const struct reset_control_ops reset_tps380x_ops = {
+	.assert		= tps380x_reset_assert,
+	.deassert	= tps380x_reset_deassert,
+};
+
+static int tps380x_reset_of_xlate(struct reset_controller_dev *rcdev,
+				  const struct of_phandle_args *reset_spec)
+{
+	/* No special handling needed, we have only one reset line per device */
+	return 0;
+}
+
+static int tps380x_reset_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	const struct tps380x_reset_devdata *devdata;
+	struct tps380x_reset *tps380x;
+
+	devdata = device_get_match_data(dev);
+	if (!devdata)
+		return -EINVAL;
+
+	tps380x = devm_kzalloc(dev, sizeof(*tps380x), GFP_KERNEL);
+	if (!tps380x)
+		return -ENOMEM;
+
+	tps380x->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(tps380x->reset_gpio))
+		return dev_err_probe(dev, PTR_ERR(tps380x->reset_gpio),
+				     "Failed to get GPIO\n");
+
+	tps380x->reset_ms = devdata->max_reset_ms;
+
+	tps380x->rcdev.ops = &reset_tps380x_ops;
+	tps380x->rcdev.owner = THIS_MODULE;
+	tps380x->rcdev.dev = dev;
+	tps380x->rcdev.of_node = dev->of_node;
+	tps380x->rcdev.of_reset_n_cells = 0;
+	tps380x->rcdev.of_xlate = tps380x_reset_of_xlate;
+	tps380x->rcdev.nr_resets = 1;
+
+	return devm_reset_controller_register(dev, &tps380x->rcdev);
+}
+
+static const struct tps380x_reset_devdata tps3801_reset_data = {
+	.min_reset_ms = 120,
+	.typ_reset_ms = 200,
+	.max_reset_ms = 280,
+};
+
+static const struct of_device_id tps380x_reset_dt_ids[] = {
+	{ .compatible = "ti,tps3801", .data = &tps3801_reset_data },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, tps380x_reset_dt_ids);
+
+static struct platform_driver tps380x_reset_driver = {
+	.probe	= tps380x_reset_probe,
+	.driver = {
+		.name		= "tps380x-reset",
+		.of_match_table	= tps380x_reset_dt_ids,
+	},
+};
+module_platform_driver(tps380x_reset_driver);
+
+MODULE_AUTHOR("Marco Felsch <kernel@pengutronix.de>");
+MODULE_DESCRIPTION("TI TPS380x Supply Voltage Supervisor and Reset Driver");
+MODULE_LICENSE("GPL v2");