mmc: at91-mci: remove obsolete driver

The at91-mci driver is not needed anymore since the atmel-mci driver now
supports all Atmel devices.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

MAINTAINERS

@@ -1352,14 +1352,6 @@ S:	Maintained
 F:	drivers/atm/
 F:	include/linux/atm*
 
-ATMEL AT91 MCI DRIVER
-M:	Ludovic Desroches <ludovic.desroches@atmel.com>
-L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-W:	http://www.atmel.com/products/AT91/
-W:	http://www.at91.com/
-S:	Maintained
-F:	drivers/mmc/host/at91_mci.c
-
 ATMEL AT91 / AT32 MCI DRIVER
 M:	Ludovic Desroches <ludovic.desroches@atmel.com>
 S:	Maintained

arch/arm/mach-at91/include/mach/board.h

@@ -70,16 +70,6 @@ struct at91_cf_data {
 extern void __init at91_add_device_cf(struct at91_cf_data *data);
 
  /* MMC / SD */
-  /* at91_mci platform config */
-struct at91_mmc_data {
-	int		det_pin;	/* card detect IRQ */
-	unsigned	slot_b:1;	/* uses Slot B */
-	unsigned	wire4:1;	/* (SD) supports DAT0..DAT3 */
-	int		wp_pin;		/* (SD) writeprotect detect */
-	int		vcc_pin;	/* power switching (high == on) */
-};
-extern void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data);
-
   /* atmel-mci platform config */
 extern void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data);
 

drivers/mmc/host/Kconfig

@@ -270,26 +270,8 @@ config MMC_AU1X
 
 	  If unsure, say N.
 
-choice
-	prompt "Atmel SD/MMC Driver"
-	depends on AVR32 || ARCH_AT91
-	default MMC_ATMELMCI if AVR32
-	help
-	  Choose which driver to use for the Atmel MCI Silicon
-
-config MMC_AT91
-	tristate "AT91 SD/MMC Card Interface support (DEPRECATED)"
-	depends on ARCH_AT91
-	help
-	  This selects the AT91 MCI controller. This driver will
-	  be removed soon (for more information have a look to
-	  Documentation/feature-removal-schedule.txt). Please use
-	  MMC_ATMEL_MCI.
-
-	  If unsure, say N.
-
 config MMC_ATMELMCI
-	tristate "Atmel Multimedia Card Interface support"
+	tristate "Atmel SD/MMC Driver (Multimedia Card Interface)"
 	depends on AVR32 || ARCH_AT91
 	help
 	  This selects the Atmel Multimedia Card Interface driver. If
@@ -298,8 +280,6 @@ config MMC_ATMELMCI
 
 	  If unsure, say N.
 
-endchoice
-
 config MMC_ATMELMCI_DMA
 	bool "Atmel MCI DMA support"
 	depends on MMC_ATMELMCI && (AVR32 || ARCH_AT91SAM9G45) && DMA_ENGINE

drivers/mmc/host/Makefile

@@ -17,7 +17,6 @@ obj-$(CONFIG_MMC_WBSD)		+= wbsd.o
 obj-$(CONFIG_MMC_AU1X)		+= au1xmmc.o
 obj-$(CONFIG_MMC_OMAP)		+= omap.o
 obj-$(CONFIG_MMC_OMAP_HS)	+= omap_hsmmc.o
-obj-$(CONFIG_MMC_AT91)		+= at91_mci.o
 obj-$(CONFIG_MMC_ATMELMCI)	+= atmel-mci.o
 obj-$(CONFIG_MMC_TIFM_SD)	+= tifm_sd.o
 obj-$(CONFIG_MMC_MSM)		+= msm_sdcc.o

drivers/mmc/host/at91_mci.h

-/*
- * drivers/mmc/host/at91_mci.h
- *
- * Copyright (C) 2005 Ivan Kokshaysky
- * Copyright (C) SAN People
- *
- * MultiMedia Card Interface (MCI) registers.
- * Based on AT91RM9200 datasheet revision F.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91_MCI_H
-#define AT91_MCI_H
-
-#define AT91_MCI_CR		0x00		/* Control Register */
-#define		AT91_MCI_MCIEN		(1 <<  0)	/* Multi-Media Interface Enable */
-#define		AT91_MCI_MCIDIS		(1 <<  1)	/* Multi-Media Interface Disable */
-#define		AT91_MCI_PWSEN		(1 <<  2)	/* Power Save Mode Enable */
-#define		AT91_MCI_PWSDIS		(1 <<  3)	/* Power Save Mode Disable */
-#define		AT91_MCI_SWRST		(1 <<  7)	/* Software Reset */
-
-#define AT91_MCI_MR		0x04		/* Mode Register */
-#define		AT91_MCI_CLKDIV		(0xff  <<  0)	/* Clock Divider */
-#define		AT91_MCI_PWSDIV		(7     <<  8)	/* Power Saving Divider */
-#define		AT91_MCI_RDPROOF	(1     << 11)	/* Read Proof Enable [SAM926[03] only] */
-#define		AT91_MCI_WRPROOF	(1     << 12)	/* Write Proof Enable [SAM926[03] only] */
-#define		AT91_MCI_PDCFBYTE	(1     << 13)	/* PDC Force Byte Transfer [SAM926[03] only] */
-#define		AT91_MCI_PDCPADV	(1     << 14)	/* PDC Padding Value */
-#define		AT91_MCI_PDCMODE	(1     << 15)	/* PDC-orientated Mode */
-#define		AT91_MCI_BLKLEN		(0xfff << 18)	/* Data Block Length */
-
-#define AT91_MCI_DTOR		0x08		/* Data Timeout Register */
-#define		AT91_MCI_DTOCYC		(0xf << 0)	/* Data Timeout Cycle Number */
-#define		AT91_MCI_DTOMUL		(7   << 4)	/* Data Timeout Multiplier */
-#define		AT91_MCI_DTOMUL_1		(0 <<  4)
-#define		AT91_MCI_DTOMUL_16		(1 <<  4)
-#define		AT91_MCI_DTOMUL_128		(2 <<  4)
-#define		AT91_MCI_DTOMUL_256		(3 <<  4)
-#define		AT91_MCI_DTOMUL_1K		(4 <<  4)
-#define		AT91_MCI_DTOMUL_4K		(5 <<  4)
-#define		AT91_MCI_DTOMUL_64K		(6 <<  4)
-#define		AT91_MCI_DTOMUL_1M		(7 <<  4)
-
-#define AT91_MCI_SDCR		0x0c		/* SD Card Register */
-#define		AT91_MCI_SDCSEL		(3 << 0)	/* SD Card Selector */
-#define		AT91_MCI_SDCBUS		(1 << 7)	/* 1-bit or 4-bit bus */
-
-#define AT91_MCI_ARGR		0x10		/* Argument Register */
-
-#define AT91_MCI_CMDR		0x14		/* Command Register */
-#define		AT91_MCI_CMDNB		(0x3f << 0)	/* Command Number */
-#define		AT91_MCI_RSPTYP		(3    << 6)	/* Response Type */
-#define			AT91_MCI_RSPTYP_NONE	(0 <<  6)
-#define			AT91_MCI_RSPTYP_48	(1 <<  6)
-#define			AT91_MCI_RSPTYP_136	(2 <<  6)
-#define		AT91_MCI_SPCMD		(7    << 8)	/* Special Command */
-#define			AT91_MCI_SPCMD_NONE	(0 <<  8)
-#define			AT91_MCI_SPCMD_INIT	(1 <<  8)
-#define			AT91_MCI_SPCMD_SYNC	(2 <<  8)
-#define			AT91_MCI_SPCMD_ICMD	(4 <<  8)
-#define			AT91_MCI_SPCMD_IRESP	(5 <<  8)
-#define		AT91_MCI_OPDCMD		(1 << 11)	/* Open Drain Command */
-#define		AT91_MCI_MAXLAT		(1 << 12)	/* Max Latency for Command to Response */
-#define		AT91_MCI_TRCMD		(3 << 16)	/* Transfer Command */
-#define			AT91_MCI_TRCMD_NONE	(0 << 16)
-#define			AT91_MCI_TRCMD_START	(1 << 16)
-#define			AT91_MCI_TRCMD_STOP	(2 << 16)
-#define		AT91_MCI_TRDIR		(1 << 18)	/* Transfer Direction */
-#define		AT91_MCI_TRTYP		(3 << 19)	/* Transfer Type */
-#define			AT91_MCI_TRTYP_BLOCK	(0 << 19)
-#define			AT91_MCI_TRTYP_MULTIPLE	(1 << 19)
-#define			AT91_MCI_TRTYP_STREAM	(2 << 19)
-#define			AT91_MCI_TRTYP_SDIO_BYTE	(4 << 19)
-#define			AT91_MCI_TRTYP_SDIO_BLOCK	(5 << 19)
-
-#define AT91_MCI_BLKR		0x18		/* Block Register */
-#define		AT91_MCI_BLKR_BCNT(n)	((0xffff & (n)) << 0)	/* Block count */
-#define		AT91_MCI_BLKR_BLKLEN(n)	((0xffff & (n)) << 16)	/* Block length */
-
-#define AT91_MCI_RSPR(n)	(0x20 + ((n) * 4))	/* Response Registers 0-3 */
-#define AT91_MCR_RDR		0x30		/* Receive Data Register */
-#define AT91_MCR_TDR		0x34		/* Transmit Data Register */
-
-#define AT91_MCI_SR		0x40		/* Status Register */
-#define		AT91_MCI_CMDRDY		(1 <<  0)	/* Command Ready */
-#define		AT91_MCI_RXRDY		(1 <<  1)	/* Receiver Ready */
-#define		AT91_MCI_TXRDY		(1 <<  2)	/* Transmit Ready */
-#define		AT91_MCI_BLKE		(1 <<  3)	/* Data Block Ended */
-#define		AT91_MCI_DTIP		(1 <<  4)	/* Data Transfer in Progress */
-#define		AT91_MCI_NOTBUSY	(1 <<  5)	/* Data Not Busy */
-#define		AT91_MCI_ENDRX		(1 <<  6)	/* End of RX Buffer */
-#define		AT91_MCI_ENDTX		(1 <<  7)	/* End fo TX Buffer */
-#define		AT91_MCI_SDIOIRQA	(1 <<  8)	/* SDIO Interrupt for Slot A */
-#define		AT91_MCI_SDIOIRQB	(1 <<  9)	/* SDIO Interrupt for Slot B */
-#define		AT91_MCI_RXBUFF		(1 << 14)	/* RX Buffer Full */
-#define		AT91_MCI_TXBUFE		(1 << 15)	/* TX Buffer Empty */
-#define		AT91_MCI_RINDE		(1 << 16)	/* Response Index Error */
-#define		AT91_MCI_RDIRE		(1 << 17)	/* Response Direction Error */
-#define		AT91_MCI_RCRCE		(1 << 18)	/* Response CRC Error */
-#define		AT91_MCI_RENDE		(1 << 19)	/* Response End Bit Error */
-#define		AT91_MCI_RTOE		(1 << 20)	/* Response Time-out Error */
-#define		AT91_MCI_DCRCE		(1 << 21)	/* Data CRC Error */
-#define		AT91_MCI_DTOE		(1 << 22)	/* Data Time-out Error */
-#define		AT91_MCI_OVRE		(1 << 30)	/* Overrun */
-#define		AT91_MCI_UNRE		(1 << 31)	/* Underrun */
-
-#define AT91_MCI_IER		0x44		/* Interrupt Enable Register */
-#define AT91_MCI_IDR		0x48		/* Interrupt Disable Register */
-#define AT91_MCI_IMR		0x4c		/* Interrupt Mask Register */
-
-#endif